14 best table saw with folds

Product description

The DEWALT DW7451 compact table saw stand delivers the best of both worlds: solid construction for a safe work environment and a compact, folding design for easy transport and storage. Heavy-duty tube steel construction provides the strength you need for safe operation. Integrated support bar hardware holes for secure fastening of saw to the stand. This stand is lightweight; it folds flat for easy handling, storage, and transport. Designed for use with the DW7480 compact job site table saw, Dcs7485 60V table saw and DW745 compact table saw. Backed by a 3-Year limited warranty.

• Heavy-Duty tube steel construction provides the strength you need for safe operation
• Upport bar hardware holes for secure fastening of saw to the stand
• Lightweight; folds flat for easy handling, storage, and transport
• Designed for use with the DW7480 compact job site table saw, Dcs7485 60V table saw and DW745 compact table saw

User questions & answers

Question:	does anyone have instructions to put the saw on the stand? #dwe
Answer:	You can view or download instructions via https://servicenet.dewalt.com/Products/Detail?productNumber=DW7451
Question:	I have the dwe7490. what is the correct stand for that model
Answer:	You can order stand #N272401 online or via the following link: https://servicenet.dewalt.com/Parts/Detail/320318
Question:	Do the legs adjust for uneven ground
Answer:	No, the legs are not adjustable.
Question:	Do this stand is foldable pretty easy for transportation
Answer:	Yes, it folds up very easily. However, it is bolted to the table saw, and it will not fold when attached, (which is good thing when you are using it!). What I do, when I haul this table saw, is just lay it on its side (with the stand attached) in the bed of the truck. It saves me unbolting the stand to haul it, and bolting it together again to to use it at the job site. The table saw that fits this stand is very light, so moving or lifting it with the stand on is no problem.

Product features

DEWALT DW7451 Compact Table Saw Stand

The DEWALT DW7451 table saw stand delivers the best of both worlds: solid construction for a safe work environment and a compact, folding design for easy transport and storage. Featuring heavy-duty tube steel construction that can support the stress of tough saw jobs, this stand is designed for use with the DWE7480 (10" Compact table saw) DCS7485 (60V 8 1/4" Table Saw) and the DW7450 (10" Compact table saw). DEWALT DW745 10-inch compact job site table saw. Integrated support bar hardware holes make it easy to secure the saw to the stand for confident operation.

Product description

The C10RJS 10" jobsite table saw features a 15-Amp motor with 4,500 RPMs, and is engineered for rip-sawing and cross-cutting of ordinary wood, hardwood, plywood and composite wood materials.



The fold & roll stand is designed with sturdy legs for easy set up and breakdown, providing stability while in use.



The stand also incorporates wheels to ensure the user can maneuver through tough terrain with ease.



The C10RJS features soft start, an electric brake and a large working table size with telescoping table extension that can support a max rip capacity of 35" to the right.



Capable of a 3-1/8" cut at 90 degrees and 2-1/4" cut at 45 degrees, this user-friendly table saw is an ideal choice for any workshop or jobsite.

• TABLE SAW: 10-Inch Table Saw with Stand
• INCLUDES: Table saw, 10-Inch 40-Tooth Carbide Tipped Blade, Blade Guard, Push Stick, Wrenches, Kickback, Rip Fence and Miter Gauge Assemblies, Outfeed Support
• MOTOR: Powerful 15 Amp motor with 4,500 RPM for tackling the toughest cutting applications.Table Material:Aluminum
• BEVEL: 0° to 45°: for cuts ranging from 3-1/8 In. (0°) to 2-1/4 In. (45°)
• TABLE SIZE: 28-3/4" x 22" working table top with outfeed support of 28-3/4" x 2" for easy and stable material support
• CUT CAPACITY: Capable of a 3-1/8 In. cut at 90 degrees and 2-1/4 In. cut at 45 degrees
• TECHNOLOGY: Featuring soft star and electric brake

User questions & answers

Question:	Hat is difference between this and more expensive version
Answer:	Depending on the models, Orbi pro supports 4 to 6 max satellites per base. SXK80 and SRR60 both support 6 satellites max. Please try to rearrange the positions of the current satellites and check if it removes the coverage holes before buying new satellites. Adding more satellites reduces the efficiency of mesh as all of the satellites share the same air-frequency. We have improved automatic detection and switching between wireless and wired backhaul in recent releases. Please upgrade your firmware to the latest.
Question:	does this come with a rack and pinion fence
Answer:	Yes. SRR60, SXR80 can be run in AP (Access point mode). Then your original router will be the NAT and DHCP server. While Orbi Pro will be Layer 2 Mesh Access point
Question:	mine has a broken bracket that mounts the gear for the rip fence. Can I get a replacement or do i need to send back a 105lb saw
Answer:	If you use the SRC60 satellite (wallmount) model, it has a wired 1G port with PoE option and if that port is used to connect it to the router, then the third radio is also freed up for fronthaul and there will be a 4x4, i.e. 1,733Mpbs available.
Question:	Metabo, i am looking for an oval dado blade insert for my c10rjs? Not the rectangular pice for the c10rj. I can't find it anywhere. Thank you
Answer:	I don’t know but I do know that I switched my three labs to It one year ago and they are quite healthy and love it.

Product features

Telescoping Table Extension

Supports 35" of ripping capacity to the right and 22" to the left.

Bevel Range of 0 Degree to 45 Degrees

For cuts ranging from 3-1/8" (at 0 degree) to 2-1/4" (at 45 degrees).

Oversized Power Switch with Emergency Off Safety Cover

Designed at knee level for immediate shut down as an added safety feature.

Stable and durable fold & roll stand

Ensures accurate cuts with less wobble and provides for easy transport.

Product description

The BORA Speedhorse is the ultimate upgrade for your job site, workspace, or workshop. Pro carpenters, woodworkers, and contractors everywhere can rely on the fast setup and easy teardown of the Speedhorse. Simply deploy the legs with the touch of a button and set up is complete, making it 30 times faster than other brands on the market. With no assembly required, it is are ready to use right out of the box. The legs fold up (in any order) into the metal beam, allowing for easy storage and convenient transport. It also has a handle that makes it even easier to grab and go. The pre-drilled metal top allows you to screw in 2 x 4’s for a sacrificial top.

• SET-UP IN 1.6 SECONDS: The Bora Speedhorse is the only sawhorse on the market with lever quick-release deploy technology, offering instant setup and teardown that is 30x faster than conventional sawhorses
• BEST-IN-CLASS CAPACITY: These sawhorses can support up to 1500 lbs each, which means a hefty 3000 lbs together! This is 200 lbs. more than the leading competitors. A working height of 30 inches tall puts your project within easy reach. Come ready to out of the box with no assembly is needed to use.
• FAST TEAR DOWN: To tear down your worksite, just pull the levers on each end and fold the legs up. Unlike standard sawhorses, these have non-sequential legs, so It doesn't matter which leg is folded first.
• LONGER, PRE-DRILLED TOP: The pre-drilled metal top allows you to screw in 2x4's as makeshift brackets to a worktop. This prolongs the life of your equipment and protects it from damage. The extra-long length of 45 inches provides maximum stability.
• AWARD WINNING SAW HORSE: The Bora Portamate Speedhorse is Winner of the 2019 Pro Tool Innovation Award in the Sawhorses & Tables category. Buy the best and add it to your cart now!
• TWO PACK: Set of 2 Speedhorse Sawhorses to get you setup with the best work support on the job.

User questions & answers

Question:	How do you "rip" cut wood boards in half length wise without cutting into the sawhorses using a circular mini saw? what's the best technique/tool
Answer:	I lay a 3/4 in thick plywood over the 2 horses. Then I put 2 boards (even 2 x 4) as a spacer to raise up your board that you are cutting. I use a straight edge to make sure my cut is straight. Clamp the board down that you want to cut......this way the sawblade will go thru the board you are working on, but not thru the board over the sawhorse or the sawhorse itself.
Question:	Any reason to buy these over the toughbuilt brand? They are quite a bit cheaper, and the legs look a little sturdier. Advantages/disadvantages
Answer:	Only $20 cheaper for the toughbuilt. The toughbuilt have to be manually opened, and can only be closed in one order. The bora opens with one hand/one switch, and it doesn't matter which legs you close first.
Question:	When used with another unit, how far apart are the 2x4's when 2 are placed in the slots in the end
Answer:	The spacing of the 2x4 slots is 41.5”
Question:	How stable are these-i've used the toughbuilt brand and they seem to rock around alot
Answer:	Not stable. They have a decent front-to-back sway. Caught me by surprise when I got them out of the box. Similar observation by others on YouTube.

Product features

Instant Set-Up Bora Speedhorse

The Bora Portamate PM-4500 Speedhorse is the ultimate upgrade for your job site, workspace, or workshop. Shave precious time off site setup and tear down so you can get to work faster and complete jobs more efficiently. The Speedhorse deploys 30x faster than conventional sawhorses — just pull the release button in the middle of the frame and you are ready to go!

Instant set-up saves you valuable time on every project!

The Bora Speedhorse sets up 30x faster than conventional sawhorses. Simply release the legs with the lever and in 1.6 seconds you are ready to begin working.

Instant Set Up

Time is never an issue when you are using the Bora Speedhorse as your work support stand. All you need to do is enable the quick-release legs and in about one second you are ready to start!

Flexible Workspaces

Having flexibility on the job site is key to working efficiently. Speedhorse lets you set up quickly and doesn't slow you down when you need to move!

Incomparable Weight Capacity

The Bora Speedhorse is best in show for its weight capacity. It leads the race with a capacity of 1500 lbs, 200 lbs more than it's leading competitors. That means that with a pair of sawhorses you can support an incredible 3,000 lbs!

Versatile

The Speedhorse allows you to get your job done fast. Setup and tear down are a breeze and the units can be adapted for use as a work table or the tried and true sawhorse.

TIme Saver

Longer, pre-drilled top — More length means more stability. The pre-drilled metal top allows you to screw in a 2x4 as a sacrificial top, saving your equipment from damage.

Non-Sequential Leg Folding

Save time setting up and tearing down! The non-sequential leg folding means you can fold the legs up in any order. No more wasted time figuring out which leg folds first.

Long LIfe

The pre-drilled metal top allows for a 2x4 to be added as a makeshift top. This will increase the life of your Speedhorse be protecting the metal top against regular wear and tear. Adding a sacrificial board also protects your cutting tools to minimize the chance that they will hit the metal frame.

2x Material Slots

Speedhorse comes standard with 2x material slots on each end of the beam. Drop your boards in each slot to connect two Speedhorses. This enables you to create work tables that get the job done!

Product description

10" Jobsite Table Saw - Model 10010.001 HIGHLIGHTED BENEFITS: Soft start feature reduces motor noise and vibration as well as greatly increases the motor life. Rapid blade elevation for quicker set-up. 2 in 1 Machine. Blade can be replaced with a sanding disc for greater versatility. 2-year mechanical and 1-year electrical warranty Lighted overload indicator prevents motor damage and will protect if the blade is blocked. Variable speed motor is easy to adjust and produces constant torque over the entire RPM range. Magnetic switch prevents unwanted start after power interruption. FEATURES: Rip fence features L-shaped attachment for use with thin stock. Fence lock for safe transportation, On-board tool and accessory storage. Left tilt blade for added safety. Spindle lock for quick blade replacement. Blade guard features a quick release for easy blade access Riving knife included for non-through cuts. Built in 2-1/2" port for efficient dust management. Adjustable rear material support safely handles large work pieces. Constant torque feature allows heavy sanding with 10" disc at any speed. Fold-up stand features roller wheels for easy transportation at jobsite. Lightweight aluminum table for easy transportation. All accessories included at no extra cost: Sanding Disc 10" 40 tooth carbide tip blade Riving knife Miter gauge Zero clearance table insert Dado insert Optional Accessories: 10010.A005 - Blade Table Inserts 10010.A004 - Dado Table Insert Specifications Model 10010.001 Blade Diameter: 10" Arbor Diameter: 5/8" Max Dado Size: 13/16" x 8" Maximum Depth of Cut at 90°: 3-1/8" Maximum Depth of Cut at 45°: 2-1/4" Maximum Rip to Right of Blade: 28" Variable Speed Blade or Disc RPM: 2,000 - 4,000 Table Size: 25-3/16" x 22-7/16" Table Height: 34" Dust Port Diameter: 2-1/2" Motor (Torque Compensation VFD): 2HP 115V Net Weight lbs.: 90

• Soft start feature reduces motor noise and vibration as well as greatly increases the motor life.
• Rapid blade elevation for quicker set-up. Light weight aluminum table for easy lifting.
• Magnetic switch prevents unwanted start after power interruption. Variable speed motor is easy to adjust and produces constant torque over the entire RPM range.
• All accessories included at no extra cost: Sanding Disc, 10” 40T Carbide Tip Blade, Riving Knife, Miter Gauge, Blade Table Insert, Push Stick
• Fold-up stand features roller wheels for easy transportation at jobsite.

User questions & answers

Question:	Is this essentially the same saw as the Grizzly G
Answer:	This jobsite has variable speed with soft start motor. In addition, it comes standard with sanding disc and 10" blade. This is basically a 2in1 machine that we recently launch last year.
Question:	How wide is the stand at the wheels? I have a tight space I would need to move it through
Answer:	It'd be 24" wide.
Question:	Does it have dust collection port
Answer:	Yes, this saw has a built in 2-1/2” port for efficient dust management.
Question:	How tall is the machine when collapsed? I need to fit it in my truck under the bed cover, which is
Answer:	25” with wheels and legs attached. It would fit under your cover if you unbolted the legs when you’re done.
Question:	Can you plug this saw into a 240V outlet
Answer:	It is only for 120 volts AC. The motor will burn-up if you try.
Question:	What is the Max cutting depth of this saw, will it handle 4x4's
Answer:	No. The saw at its highest point is only 3 1/4 inches from table to the tip of the blade. In order to cut anything thicker you would need to flip the wood over to finish the cut.
Question:	is blade included
Answer:	Yes, a blade is included
Question:	I want to build a crosscut sled. What is the distance from the front of the blade to the end of the T-rail in front
Answer:	I ran the blade all the way up and measured from the edge to the blade at 7 3/4". Measured from edge to the opening in the throat plate 7 1/2". Hope you enjoy your saw as well as I do mine.

Product features

DEWALT 10-Inch Jobsite Table Saw with 32-1/2-Inch Rip Capacity and Rolling Stand

The DWE7491RS 10" Jobsite Table Saw 32 - 1/2" Rip Capacity, and a Rolling Stand has a 15 Amp motor and 32-1/2" rip capacity to allow cutting of large and hardwood materials. Features tool-free guarding component adjustments and fast, accurate fence adjustments. Rolling stand designed for easy set up and breakdown with excellent stability.

FEATURES

• Rack & Pinion Telescoping Fence System Make fence adjustments fast, smooth and accurate
• Patented material support, can be used for narrow rip cuts
• Rolling stand designed for easy set up and breakdown with excellent stability
• Telescoping fence rails retract to create a small, portable package
• Flip over ripping fence allows for narrow rip cuts

• 2-1/2" Dust Collection Port easily connects to a vacuum for efficient dust extraction
• 3-1/8" depth-of-cut at 90 and 2-1/4" at 45
• 21-7/8" X 26 - 3/8" table provides superior material support

60-Tooth Crosscutting and 32-Tooth General Purpose 10-Inch Saw Blade

FEATURES

• Thin kerf design for smooth, fast cutting
• Ultra sharp construction carbide for long life and clean cuts
• Anti-kick back shoulder increases durability and helps prevent binding

Product description

The Bora centipede support stand is a sturdy, portable workbench and saw table base. Made of heavy-duty steel, It sets up in seconds. When you’re ready to leave the job site, It folds down into a compact, lightweight carry bag for easy transport and space-saving storage system. Featuring a unique metal frame design, each support is constructed of multiple steel Struts that rest directly between the load and ground. This structure offers rigid stability while keeping even the thinnest sheet materials from sagging. Various accessories can be used with the equipment Stand, from Sawhorse to planning tables. Bora tools designs to maximize your utility, comfort, and convenience.

• SAW-HORSE SOLUTION - made of heavy duty steel construction, The centipede is a foldable work stand that can be set up as a large portable workbench at any job site
• COMEPLETE KIT - The full set comes with the following accessories: 4 quick Clamps to keep your materials firmly in place, 4 X-shaped brackets which hold standard 2x4 boards steady, and a sturdy carry bag
• WORK HEIGHT - the working height is 30 inches tall: Large enough to lay a 4ft x 8ft wood board on top. It’s expandable by simply adding risers (not included) for an increased working height. It supports up to 6, 000 pounds of power tools and machinery
• VERSATILE FUNCTIONALITY - Choose from 4 sizes, CK6S, CK9S, CK12S and CK15S. The larger the base, the more weight the table can hold. The wider sizes allow you to complete 2 jobs at once
• INSTANT SET UP – this stand is ready to use right out of the box, no Assembly required. It takes just seconds to set up. When the job is done, it conveniently folds up for easy storage and transport
• CK22T Table Top - Now available for a portable work top option with 3/4-inch bench dog holes
• Depending on the size of your Centipede workstand, you may need more than one Tabletop for full coverage. CK6S needs 1, CK9S needs 2, CK15S needs 4.

User questions & answers

Question:	Could this be used as a stage riser? With a drummer and drum set on it
Answer:	The specs on Amazon states that it can handle up to 6,000 pounds of machinery and tools. You be the judge, what is the weight of the drum set and whomever will play them? Will there be others on that stage? In my opinion, if what you put on it is stationary and one person sits on the drum set, nit and that's it, it could work okay. If you are going to have more than one person on it bouncing around like some musicians do, I'd be concerned....there is a big difference between stationary objects on it and bouncing around. My big centipede expands slightly beyond 4'x8' and two edges along the perimeter can be unsupported. If you do use this as a riser, I recommend that you ensure that the entire perimeter of whatever you place on the centipede is supported and the centipede does not expand beyond 4'x8'.
Question:	Can the 4x8 be expanded to just 4x4 or other sizes smaller than 4x
Answer:	No it can't. The 4x8 must be fully expanded as designed. Only when fully expanded can the Centipede support very heavy workloads.
Question:	Has anyone used this with their track saw
Answer:	I did. And I should of adjusted the saw blade depth cause I nicked the plastic holders but you live and you learn. Worked very good by the way. That's the reason I bought it
Question:	What are the dimensions of the unit when collapsed
Answer:	9 x 15 x 38 inches

Product features

4' x 8' Work Support Table

The Bora Centipede CK15S Workstand is the most flexible solution for your job site, work space, or workshop. It turns into a 4ft x 8ft workstation in seconds-no assembly required.

Flexible yet tough, the Centipede allows you to create a custom work space to fit your needs, wherever that may be. Use it at the beach for a dining table, a place to set gardening tools in the yard, or on your job site to look at plans while someone else saws. The options are endless!

Flexibility

Today’s workspace needs to be flexible. Centipede allows you to change locations and setups to suit the task at hand. Whether you are on the job or in the workshop, you will have the support needed to get the job done while doing your best work.

Table Top Option Now Available

The CK22T table top securely fastens to the P-Top's on your work stand with the 6x quick twist locks (included with purchase) for a portable work top option. Table top has 3/4-inch dog holes and the dimensions are 24" x 48" (610 mm x 1200 mm) – same size as the CK6S. It is hinged in the middle for easy clean up and transport.

Tackle Any Size Job

Centipede is built for the big jobs with it's innovative design and functional accessories. Instant setup and rugged construction allows you to grind, saw, cut and more.

Unbeatable Weight Capacity

Jaw dropping weight capacity means you can rely on your Centipede during crunch time. Each model delivers thousands of pounds of capacity without sacrificing portability or ease of setup.

CK15S Work Stand

The 15 Strut portable work stand is an easy solution for jobs where you have limited space, need quick set up and take down, and a work station that moves around the work site with you.

4) 2x4 Support Brackets

Get quick cuts without clamping when using the X-shaped 2x4 support brackets, four pieces included with your purchase. Designed to fit standard 2x4 boards on the edge or face, these X-shaped cups will allow you to spend less time setting up and more time working.

4) Quick Clamps

Quick Clamps keep your materials securely held in place when when inserted into the P-Top on your Bora Centipede work stand. Quick clamps fit in standard 3/4 in, bench dog holes.

Carry Bag

Made of rugged canvas with a sturdy yet comfortable strap, this bag will fit your CK15S and accessories. Keep your equipment safe and dry when you need to transport or store it for later.

Product description

If you have a miter saw, then the PM-4000 folding miter saw stand is exactly what you need. Designed to work with nearly every make and model miter saw or chop saw, this strong, stable stand will allow you to setup wherever you wish – quickly, easily, and safely. Whether it’s a jobsite or your driveway, you’ll appreciate being able to work exactly where you need to. This is a contractor grade miter saw stand, but priced for the homeowner. But don’t let the low cost fool you – this is a high quality piece of equipment, with tubular steel construction, and a whopping 500lb capacity, so you can handle the big jobs with ease. The quick attach mounts make attaching and detaching the saw simple, and the adjustable 13” tall material supports can be in or out to support material ten feet long. But here’s the kicker – it’s not only lightweight, but it folds up for easy transport and storage, making this one of the most versatile miter saw stands on the market. An optional Wheel Kit is available (PM-7004) for added mobility, and extra tool mounts (PM-7002 – 20-in long and can be adjusted along the width to fit most saws) are also available allowing you to expand the use of your stand to other tools in your shop.

From the Manufacturer

If you have any questions about our product, please contact us by emailing [email protected] or calling 1-866-588-0395.

• A cut above - The Bora Portamate PM-4000 is the best, most practical, hassle-free stand you’ll find for miter saws or chop saws. Constructed of tubular steel with a powder-coated finish, This rugged yet lightweight saw stand can support up to 500 lbs. And is compatible with Miter saws up to 12 inches, including compound sliding saws.
• Cut out for convenience - setup is quick and simple, as the folding legs swing Under the center portion and are secured by pins that snap into position. Stand folds up for easy transport, storage and carrying from your vehicle to the worksite. Folded size is 43. 5" W x 20" D x 6. 5" H and Weighs only 30 lbs. Without a saw.
• Switch gears & mount add tools - quick-attach saw mounts allow for easy mounting of your saw, as well as other tools which you can switch around, set up and take down quickly – hardware is included. Additional mount sets sold separately offer a wider variety of tools that you can use with your PM-4000 stand.
• Makes the cut – our PM-4000 saw stand was specially designed to provide the ideal ergonomic working height of 36 inches, so professional contractors and day's can work safely and comfortably while making cuts with absolute precision and secure stability.
• Any way you cut it – Buy with confidence knowing that you are backed by our 1-year . If for any reason, you're not 100% satisfied with your purchase, let US know, and we'll make it right.

User questions & answers

Question:	Anyone have a slick way to set up a stop block on this for repetitive cuts of the same length
Answer:	One way to do this is to create a sub-fence that attaches to the fence of your miter saw. The sub-fence needs to be long enough to rest on the outrigger arms and accommodate your cut length. Once you have that in place you can clamp a block or other type of stop to the false fence. Position the stop where you need along the sub-fence and then you can do repetitive cuts. If you have any more questions regarding this product, please call the manufacturer at 248-588-0395 or send us an email at [email protected]. Thank you
Question:	can we use it with the Hitachi 10" miter saw with laser
Answer:	I have a hitachi C10FCH2 10" with laser. I needed to use the offset mounting brackets that came with the stand.Worked great
Question:	How can you order replacement bolts to lock down the saw
Answer:	The carriage bolts are 8MM, but 5/16" will work fine as long as you get new nuts as well. Like it was said, you can get those at any hardware store for less than $2. I had to replace mine, since the supplied bolts were a little too long for my old saw's base.
Question:	What is the assembled dimensions of the stand w/o the arms extended? I am looking for the dimensions between the feet when open. Thanks
Answer:	The top frame of the stand is 8-3/4" deep and 44 "wide. At the floor the outside dimensions are 54-3/8" wide by 24-3/4 deep. Since the legs slope outward and are about 1-1/4" square you could get the inside dimension by subtracting 2-1/2". If you need to put something under the stand you must allow for the slope of the legs. The arms extend about 36" each side. The two support beams for the saw or other tool are 20" long and extend about 4'' over the front top 44" beam and 7" behind the rear top beam. I use a DeWalt 12 miter saw on mine and have found the stand to be strong and stable.

Product features

BORA Portamate PM-4000 Folding Miter Saw Stand

Designed for the contractor and DIYer alike, the PM-4000 Portable Folding Miter Saw Stand makes it easy to work where the job is—from the commercial construction site to the driveway or garage.

Quick Setup & Takedown

Folds up for easy transport, storage and carrying from your truck or van to the work site. Folded size is 43-1/2in (W) x 20in (D) x 6-1/2in (H) and weighs only 30 lbs - without saw.

Extra Tool Mounts make Easy Tool Switches

Change your tools easily with quick attach mounts. Additional mounts (sold separately) allow you to have a wide variety of tools that can mount quickly and easily to your PM-4000 stand.

Comfortable Work Height

Stands at an ideal working height of 35 inches to make your work safe and efficient. This design increases stability and accuracy.

Upgrade as Needed

You can easily add more maneuverability to your Bora Portamate PM-4000 Miter Saw Stand with our PM-4004 dual wheel upgrade kit, which is sold separately. The dual 6-inch diameter wheels make navigating through the jobsite a smooth ride, rather than an added project. This optional add-on kit includes two 6-inch wheels, hardware and installs. No drilling needed - just snap, and secure wheels to the PM-4000 miter saw stand, and it's ready to roll!

Universal Tool Mounts (included)

• Minimum distance between bolt centers: 6-1/2 in. (16.5 cm)
• Maximum distance between bolt centers: 18 in. (45 cm)
• Fits any width between saw mounting holes as tool mounts are not connected
• Offset wings accommodate saws where front/back mounting holes are not in-line to each other

PM-4000 Specs

• Extending arms adjust from 45 in. (114 cm) to 114 in. (290 cm)
• Height from top to bottom: 35 in. (89 cm)
• Width from front leg to back leg: 53-3/4 in. (136.5 cm)
• Max capacity: 500 lbs.

• CONVENIENT AND SAFE: It features a roller head with triple functions, a material stop, ball bearing roller and directional roller. With 8 independent, multi-directional, smooth rollers material can move from front to back and side to side with perfectly level alignment every time. Custom feet keep stand stable and secure when locked.
• HEAVY DUTY STEEL CONSTRUCTION: All-purpose tool designed to support and move large, heavy material, such as plywood or pipes. 2 inch down tubes create an extremely strong structure, while the galvanized steel rollers allow materials to glide smoothly on top.
• COMPACT AND ADJUSTABLE: Height lever that easily locks and unlocks to effortlessly adjust work position anywhere from 27.5 inches to 43 inches at full extension. Legs fold flat for compact storage.
• BUILT TO LAST: Designed to withstand the most rugged work environments, it’s like having an extra set of hands in your work shop, providing the support you need and it is covered by our limited lifetime warranty to the original purchaser against defects in material or workmanship.
• USA QUALITY CONTROL: ToughBuilt products are designed, engineered, tested, and inspected in the USA to ensure high quality. You can be sure that you're getting the toughest Saw Stand on the market.

User questions & answers

Question:	how much weight can the roller stand/support stand hold
Answer:	The TOUGHBUILT S200 roller stand can hold a maximum weight of 100 lbs.
Question:	Does it have a built in stopper
Answer:	Don't know. What do you mean by a built in stopper?
Question:	What I the dimensions of the roller? Some customers said that roller don't turn, so does it turn or not
Answer:	The roller is approximately 11 1/2 inches in length and about 2" in diameter. It does indeed roll/turn quite freely. In case you wondered, here are the rest of the pertinent dimensions as well: Height (shortest) about 27", height (fully extended) about 44", footprint when open and in use 20"X17". Hope this helps.
Question:	can the post for the roller be removed to be cut down? It looks like a reasonably priced stand but is too tall for the main machine we need it for
Answer:	the "rollers" don't roll they're stationary, but they can be removed completely from the stand..at least mine can.

Product features

ToughBuilt Value

Some people think that to get the best of anything, you have to pay a lot. That doesn't work for us. We're tradesmen, designers, engineers, and manufacturing experts. We take pride in value engineering every ToughBuilt tool to give you unprecedented performance. Like you, we work hard to work smarter. We take pride in providing building quality and innovation.



Your ToughBuilt



ToughBuilt is inspired by you and is designed from its inception to make your work easier and more efficient. We are dedicated to delivering innovation to you. The journey of creating the best tools is just the beginning. Our intention is to provide an avenue for each of our customers to have a voice in improving what we do. We welcome your participation and any constructive criticism or comments that may help us improve and build better tools.

 

TB-S210 3-IN-1 Roller Stand

The ToughBuilt 3-in-1 Roller Stand is an ideal, all-purpose tool designed to support & move large, heavy material, such as plywood or pipes, any way you need it. It features a roller head with triple functions: a material stop, ball bearing roller & directional roller. With 8 independent, multi-directional, smooth rollers material can move from front to back & side to side with perfectly level alignment every time. This roller stand has easily adjustable height from 27.5” to 43” inches at full extension. The 3-in-1 Roller Stand is like having an extra set of hands in your work shop, providing the support you need.



Features and Benefits

•  3 in 1 head adjusts to use ball bearings, roller or sliding plate.
•  Quickly adjust height from 27.3-43.9".
•  Folds flat for easy storage.
•  Galvanized steel rollers provide support & smooth movement.
•  2” box tube frame creates an extremely strong structure.
•  Custom feet keep stand stable and secure.
•  Heavy-duty steel construction provides strength and support.

Dimensions

Closed position: W 16.93 x D 3.54 x H 30.91”

Open, low position: W 16.93 x D 22.05 x H 27.36-43.90"



Weight: 11.95 lbs

 

Product description

The C10RJ 10" Jobsite Table saw features a 15-Amp motor with 4,500 RPMs, and is engineered for rip-sawing and cross-cutting of ordinary wood, hardwood, plywood and composite wood materials. The fold & roll stand is designed with sturdy legs for easy set up and breakdown, providing stability while in use. The stand also incorporates wheels to ensure the user can maneuver through tough terrain with ease. The C10RJ table saw features soft start, an electric brake and a large working table size with telescoping table extension that can support a max rip capacity of 35" To the right. Capable of a 3-1/8" Cut at 90 degrees and 2-1/4" cut at 45 degrees. This user-friendly table saw is an ideal choice for any workshop or jobsite.

• Same tools. New name. Hitachi power tools has renamed to Metabo HPT
• Telescoping table extension supports 35" Of ripping capacity to the right and 22" To the left
• Soft start function reduces noise and recoil at start-up.Table Material:Aluminum
• Equipped with a 3/4" T-slot miter gauge that features a large scale with adjustable positive stops at 0, 15, 30, 45 and 60 degrees to the left and right to help guide material accurately for a truer cut
• Direct drive Universal 15 amp motor produces 4, 500 RPM to power through the toughest ripping applications
• 8 x 13/16" Dado capacity allows for simple dado cuts
• Oversized power switch with emergency off safety cover is designed at knee level for immediate shut down as an added safety feature

User questions & answers

Question:	How is this saw
Answer:	Ones are outside dimensions and the smaller one is the inside dimensions
Question:	Does this saw cut 47 degrees
Answer:	It will work on anything with a 2 inch reciever.
Question:	I bought a used Hitachi table but when i got i home i plug it in and only thing that happened you could hear a humming sound from the motor but it wo
Answer:	The overall dimensions are 54X27 including the hitch. Inside dimensions of the cargo area are about 52X17.
Question:	Skilsaw portable stand
Answer:	Yes but I had to purchase an extender because if was too low to the ground. Hope this helps

Product features

Telescoping Table Extension

Supports 35" of ripping capacity to the right and 22" to the left.

Bevel Range of 0 Degree to 45 Degrees

For cuts ranging from 3-1/8" (at 0 degree) to 2-1/4" (at 45 degrees).

Oversized Power Switch with Emergency Off Safety Cover

Designed at knee level for immediate shut down as an added safety feature.

Stable and durable fold & roll stand

Ensures accurate cuts with less wobble and provides for easy transport.

Product description

The ToughBuilt C550 Sawhorse and Jobsite Table is durable, rugged and offers unparalleled value. Constructed of 100% high-grade steel, this sawhorse has a remarkable 1100 lb. capacity alone, and 2200 lb. per pair. Features 2x4 support arms that transform 2 sawhorses into a solid jobsite table. Also includes innovative material support pegs that allow upright storage of materials and easy cutting. It also has easy-to-fold steady feet for all-surface use. With fast-open legs, setup is straightforward and simple. Powder-coated and zinc-plated steel prevents corrosion and withstands rigorous environments. This folding sawhorse includes an easy carry handle for effortless transport and rolled edges for safety and comfort.

Set Contains:

1 x Sawhorse

• HEAVY DUTY FOLDING SAWHORSE — Constructed from 100 percent high-grade steel, this sawhorse is rugged and capable for your most demanding jobs. Alone it has an incredible 1100 lb. capacity. When paired with a second table, it has a 2200 lb. capacity per pair.
• CREATE A STURDY JOBSITE TABLE — Durable sawhorse has 2 x 4 support arms, when deployed transform two sawhorses into a solid and sturdy jobsite table. Adjustable height legs quickly configure to your work. Has quality material support pegs and pivoting feet that adjust to your needs.
• FOLDS TO AN EASY CARRY SIZE — Strong steel legs fold into a convenient collapsible size. Platform has rounded edges for safety and security. Easy grip handle allows effortless carry to jobsite. Excellent workbench for construction, firewood cutting, drywall, and other tasks.
• U.S.A QUALITY CONTROL —Designed, engineered, tested, and inspected in the USA to ensure high quality. You can be sure that you're getting the toughest sawhorse around.
• BUILT TO LAST — Constructed from powder-coated and zinc-plated steel, you'll never have to worry about corrosion. Withstands the most rigorous environments, and it’s covered with our limited lifetime warranty to the original purchaser against defects in material or workmanship.

User questions & answers

Question:	Is the price for a pair of hirses or one horse. There are two conflicting answers
Answer:	Good so far... have not used it much.. it needed a tiny bit of tweaking but it was easy... assembly was easy also, read the manual first before you start that will make it go fast..
Question:	How tall are these extended all the way
Answer:	Yes
Question:	Is this price for 1or
Answer:	It might be your start switch look on you tube for explanation of trouble with on off switch. I called hitachi and they sent me a new one that I replaced myself
Question:	Is it for the pair or just one?? I'm so confused... For every person that answers for the pair it gets countered with a reply for one
Answer:	Has its own stand

Product description

The 10-inch Heavy Duty Worm Drive Table Saw is the latest addition to SKILSAW’s table-saw lineup. SKILSAW’s legendary Worm Drive power train delivers superior torque, an aggressive 3-5/8-inch depth of cut, and 30 ½-inch rip capacity. Tear through plywood and slice 4x with ease and precision. The rack and pinion system makes fence adjustments quickly and smoothly for accurate cuts. SKILSAW’s patented Dual-Field Motor runs cooler so it can work harder, longer. The rugged stand delivers dependable stability, and the sixteen inch wheels easily take the stairs and roll over uneven surfaces to just about anywhere you need to set up and let it rip.

• Legendary worm drive gearing with 3-5/8 inch depth of cut and 30-1/2 inch rip capacity
• Precision rack and pinion fence system makes fence adjustments quickly and smoothly for accurate cuts
• Rugged rolling stand with 16 inch Wheels and easy-load handles delivers unsurpassed mobility
• Dust port elbow contains debris to 1 area for clean-up
• Outfeed and left support allow for larger cuts to be made by 1 person

User questions & answers

Question:	Can you install a vacumm
Answer:	Good afternoon. From what I can find the RK7321 is a heavier built unit with a little more metal and less plastic and includes a wall mount which is not indicated with the RK7323.
Question:	What are the dimensions of the saw unit when off the stand/cart? I’m wanting to store the stand and saw separate for space considerations
Answer:	I bought the saw for just this reason, and was dissatisfied enough that I sent the saw back. The specs say that it will cut wood 1½" wide. Standard pinewood derby cars are 1¾" wide, so they're out of spec, and I can tell you from experience that it's definitely too much for the saw to handle. Even trying to make vertical cuts through the car body, which is only 1¼" tall, is too much for this saw. I tried a bunch of other scrap pieces of wood of varying widths, and with varying (better quality) blades than are included in the kit. I couldn't get the saw to make satisfactory cuts on anything wider than ½". So if you want to make pinewood derby cars, you're better off spending $50 more or so for a small band saw.
Question:	Does anyone know how big is the shipping box? I want to order this to my postal box and I need to know if I can load it in my trunk
Answer:	I have found 1.5 " to be the maximum. I have cross cut 2 x 3s, & ripped a 2x2 (32" long) down to create a custom 1 1/8" for repairing a hollow door--- However that long rip cut took about 10 minutes, using a 'fast' cut blade. It is very slow going on a rip cut-- like 1 mm per 2 seconds. I would expect it would also be very slow on 1" hardwood. It is okay for crosscuting lumber & scroll work & custom part making (slow cuts)... But not a heavy duty machine for production parts
Question:	Is skilsaw spt70wt-01 the same saw as skilsaw spt99-11 just without the stand/wheels
Answer:	It's made of hard black plastic.

Product features

10 In. Heavy Duty Worm Drive Table Saw

The 10-inch Heavy Duty Worm Drive Table Saw is the latest addition to SKILSAW’s table-saw lineup. Featuring the legendary Worm Drive power train this table saw delivers superior torque that rips through wood with ease. With an aggressive 3-5/8-inch depth of cut, and 30-1/2-inch rip capacity this table saw can handle materials without bogging down. The heavy-duty table saw has a best-in-class 15-amp Dual-Field Motor that powers and keeps the motor cool through continuous cuts and ripping through full sheets of plywood and 4x material.

The rack and pinion system makes fence adjustments quickly and smoothly for accurate cuts. The rugged stand delivers dependable stability, and the 16 In. wheels easily take stairs and roll over uneven surfaces to just about anywhere the saws needs to set up. Ideal for applications such as ripping and cross-cutting. Works with soft, hard and engineered woods.

Included with the SPT99-11 is rolling stand, 24-Tooth SKILSAW carbide blade, miter gauge, smart guard system including anti-kickback device, dust elbow, insert plate, push stick, wrench and rip fence.

Legendary Gear Train

The newest addition to the SKILSAW table saw family, the heavy-duty table saw has the legendary worm drive gearing. It has a powerful 15 Amp motor and a 5,000 no-load RPM.

Accurate Cuts

The rack and pinion systems quickly adjusts settings for accurate cuts.

Minimal Cleanup

The dust port connects to a standard 2-1/2 in. vacuum hose. The included dust elbow allows for minimal clean-up.

Durable Stand

The stand easily goes anywhere on the jobsite. Featuring 16 in. wheels this stand can handle uneven surfaces, go over stairs and be pushed into the bed of a truck without having to remove the saw from the stand. Also has built-in left side support for cutting large material.

Product description

Utilising patented Evolution multipurpose cutting technology, the RAGE 5-S multipurpose table saw will easily cut steel, aluminium, wood and plastic using just one blade. The cut is fast clean and accurate, producing no burr and virtually no sparks when cutting steel. There is no heat build-up either, so the material is cool and can be handled straight away. This product gives the user an opportunity you can not find with any other table saws. The RAGE 5-S features a powerful hi-torque motor, clear and precise angle settings for mitre and bevel cutting. Additionally, the blade height can be adjusted for cutting a variety of materials. Furthermore, the built-in wheels allow for easy transportation/portability and the folding stand allows for easy storage. The RAGE 5-S is supplied with a R255-TCT multipurpose blade (28 teeth), with a 255 mm blade diameter and 25.4 mm bore diameter.

• Multi-material: Japanese tungsten carbide tipped (TCT) blade included cuts steel, aluminium, wood with embedded nails, plastic and more
• Powerful: 15 A optimised gearbox and blade system, increases motor and blade life to cut through a variety of materials with ease
• Accurate: Rip cutting, assisted by an adjustable, full-length, parallel fence with measuring rail guide; 0 degrees - 45 degrees bevel tilt and 60 degrees - 60 degrees mitre covers all common cutting angles
• R255-TCT multi-material blade (28 teeth) included
• 3 years limited warranty

User questions & answers

Question:	Where can i buy Replacement blades
Answer:	I'm sure it can, but I wouldn't personally do it with this machine. I recently had an issue with my planer where the straight-knife cutterhead was damaged. That's a long story in itself. Anyways, under warranty I had a certified Jet mechanic replace the cutterhead with a new one, which is the same operation you'd do if you replaced it with a helical head. He had a VERY hard time doing it and it even involved his machinist making him a special tool just to disconnect the cutterhead from the gearbox. Not only that, you'd never get your money back out of it. So, if you want a helical head I'd recommend spending the extra money to buy the helical-head version of this planer. This is the path I wish I would've taken.
Question:	Does this saw come with stand
Answer:	You might check to see if blades are installed the right way !!!
Question:	can you cut laminateflooring with this blade
Answer:	Clean your rollers. I use rubbing alcohol and a lintfree cloth. Its a pain to do but makes all the diffrrence. Note that the rollers only move when the machune is running so i carfully clean what a can then flip the machine on and off again quick and wait till it stops and clean. I usually have to repeat that 5 or 6 times to get the entire roller. Careful to as thise blades show no mercy to gloved hands. Dont ask how i know but they did slice thru a 20 dollar pair of gloves like they were paper.
Question:	Can you cut datos with this saw
Answer:	There are three blades in the pack. And they are double sided, so you can flip them and have a new plane surface. Easy to do.

Product features

Powerful 15A Motor

Cut through up to 1/4" mild steel thanks to Powerful 15A hi-torque motor with optimized gearbox & blade system

45° Bevel Capability

Achieve a 45° finish on your workpiece by turning the bevel wheel at the front. Use the detents to reach the required angle every time!

Sliding Table

When making a cut using the sliding table, ensure the anti-vibration clamp is secure to achieve a clean, precise cut

Built-In Table Extensions

Left and right table extensions support wide work-pieces with a table surface area of 47-1/4 x 25-3/16" when fully extended

Easy to Transport & Store

Thanks to the collapsible frame, foot pedal and wheels, going from cutting, to storing the RAGE5-S is a very quick & easy process

Effective Dust Extraction

Keep your workshop clean! With Integrated dust ports above and below the blade, dust is captured when fitted to a vacuum system

Mild Steel

Cut weld-ready mild steel, whether that be 1/4" sheet or tube material (round & square)

Wood with Nails

Cut through hardwood, softwood, reclaimed timber. Even wood with embedded nails!

Aluminum

Cuts through aluminum materials such as checker plate or cable tray with virtually no heat or sparks!

Plastics

Cuts through plastics such as acrylic sheets & drainage tubing cleanly without burning or melting

Product description

The DEWALT DWE74911 Rolling Table Saw Stand is designed for easy setup and break down with excellent stability. This stand is lightweight for enhanced mobility and portability. It features durable steel construction, and is designed for easy loading and unloading into and out of vehicle. Can be used with DWE7490X, DWE7491RS, DWE7499GD, DWE7480 and DW745.

• Durable steel construction
• Easy setup and break down with excellent stability
• Designed for easy loading and unloading into and out of vehicle

User questions & answers

Question:	Will this work with a dcs7485t
Answer:	Hi, thank you for your inquiry, The PDP Xbox One LVL 1 Chat Gaming Headset can be used with any Xbox remote with a 3.5 mm headphone jack input as well as any smartphone or other device with a headphone jack. Hope this helps. PDP Customer Experience
Question:	Is this stand compatible with the dewalt dwe7485 8-1/4 in. compact jobsite table saw
Answer:	Chat and game volume
Question:	does it work for flexvolt table saw
Answer:	Yes you can.. I've owned mine for about 2 weeks now and I have zero problems with it.. it works great
Question:	Can this stand work for a dewalt dwe
Answer:	No you do not. We have two Xbox one controllers. First generation needs adapter. Second generation does not.

Product description

The DEWALT DWST11031 Adjustable Metal Legs Sawhorse is designed with a high quality combination of metal and plastic for a load capacity of up to 2500 lbs per pair. This sawhorse has a unique mechanism with easy slide movements with clear large numbers to indicate height. for work on uneven surfaces. This unit has rubber inserts on legs, and upper ruler for stability, along with a V-groove ruler for work with lumber or pipes.

• Imported from: Israel
• POWER TOOLS
• Commercial Brand: DEWALT
• High quality combination of metal and plastic
• Load capacity of up to 2500 lbs per pair
• Legs can be adjusted separately
• V-groove ruler for working with lumber or pipes

User questions & answers

Question:	hi is the metal aluminum or steel? thanks
Answer:	The metal is steel.
Question:	Adjustable hieght? What is the minimum and maximum heights? I assume 32.7 inches is the maximum height; however, if it's adjustable, what is the min
Answer:	The minimum is 31 inches and the maximum height is 39 inches. I hope this helps
Question:	Where can I buy replacement parts
Answer:	Unfortunately there are no replacement parts for the this saw horse.
Question:	how large is t5he top
Answer:	27 x 1 5/8

Product description

The new Bosch GTA500 is exclusively designed for use with the Bosch GTS1031 Table saw. Featuring a solid and durable All steel design, Solid center of gravity for maximum performance. Its tool free functionality allows the attach and detach saw in seconds and its light weight of 14 lbs. Makes it easy to carry.

From the Manufacturer

The Bosch GTA500 Tool-free Folding Table Saw Stand is a perfect accessory to accompany your GTS1031 10 in. Portable Jobsite Table Saw. The stand features a tool-free Functionality - Attach and detach saw in seconds, without tools. All-steel design, solid center of gravity for maximum performance.

• Exclusive compatibility with GTS1031
• Attach and detach saw stand in seconds, without tools
• Folds flat for convenient for transport and storage
• Solid and durable – all-steel design with solid center of gravity for maximum performance
• Light weight – weighs only 14 pounds and can be easily carried one-handed

User questions & answers

Question:	What are the dimensions of the stand when it is folded
Answer:	I needed to of the same horses and I got one of each So that's why I don't want em no more
Question:	Does this work for the Bosch 4000 10" table saw
Answer:	They are 28 3/4 tall, 41 1/2 wide
Question:	I usually buy bosch but i got a dewalt dw745 table saw. now they've discontinued the stand for it. anybody know if this will work with it
Answer:	i don't know about this one it is from i difference supply the one i bought is below and it stated 2pack 2-Pack TOUGHBUILT C550 41.5-Inch Steel Folding Portable Heavy Duty Sawhorse Jobsite Table
Question:	What height is the top of the GTS 1031 while it is on this stand
Answer:	March 2021 The Home Depot price is exactly the same as Amazon. They sell this product individually, NOT a two pack, unless you buy 2 @ $35 each. $70 plus tax for a pair.

Product features

Bosch GTA500 Folding Stand for 10-Inch Portable Jobsite Table Saw

The new Bosch GTA500 is exclusively designed for use with the Bosch GTS1031 table saw. Featuring a solid and durable all steel design, solid center of gravity for maximum performance. Its tool free functionality allows the attach and detach saw in seconds and its light weight of 14 Lbs. makes it easy to carry.