14 best tile blades

• ★FIT SIZE: Outer Diameter: 115mm (4.5 inch). Thickness: 1.2mm. Suitable for most tile saws and hand-held angle grinders with a 7/8" Arbor.
• ★HIGH PERFORMANCE: Tanzfrosch tile cutter blade outer edge is plenty strong, X teeth offer fast and smooth cutting. Thicker center to avoid vibrations and wobbling. High-Performance diamond matrix provides long life and enhanced material removal.
• ★COMPATIBLE MODELS: It can be used on different types of angle grinders and tile cutters for Wet and Dry cutting.
• ★WIDE APPLICATIONS: Tanzfrosch tile cutter blade is designed for cutting porcelain, ceramic tile, granite, sandstone quartz, marble, brick, slate, cement backer board . It will be a perfect partner for tile installers and general homemade DIYers.
• ★BUY WITH CONFIDENCE: If any of our products fail to meet your expectations, please get in touch with us and we will try our best to resolve the issue.

User questions & answers

Question:	Does this require water for cutting
Answer:	It should fit all grinders. It fits right on most grinders, it comes with a spacer to put on in case needed for a smaller shaft spindle
Question:	Will this fit a Porter Cable 7 inch wet tile saw
Answer:	Technically it can cut through concrete, but since concrete floors are generally much much harder than tiles, brick and concrete slaps ( which are what these blades intended to cut), dont expect the blades to last very long. I recommend doing it slowly and using little bit of water to prolong the life of the blades.
Question:	This fit dewalt grinder
Answer:	As with most corded drills and grinders, when the trigger is released, the grinder wheel continues to spin down to a stop.
Question:	Will it cut through a concrete floor? I want to cut out a line where its cracking and then bang it out to have a straight cut
Answer:	That's tough a vacuum works the best I think as the shroud limits depth of wheel alot we have used boshe hepa guard and vacuum on this grinder

Product features

Package Included:

3 x Diamond Saw Blade

Product description

4" Porcelain saw Blade

Size:4inch

Arbor:22.23mm

Thickness:1.2mm

Segment Height:10mm

Blade Length:105mm

Application:Porcelain tile, Granite ,Marble,stone ,ceramic

• Universal for dry or wet cutting
• X teeth offer fast and smooth cutting
• High temperature extraction diamond blade has a long service life.
• Super thin porcelain saw blade with free chips for cutting,Match with hand-held machine
• Available for cutting porcelain,ceramic tile,granite, sandstone quartz ect

User questions & answers

Question:	What is the RPM for this blade
Answer:	Not sure
Question:	What is the return policy
Answer:	Looks simple
Question:	Hi i was trying to used this blade on my 7 inch chicago electric bridge tile saw the saw keeps cutting out once the blade ii on the saw (whats wrong
Answer:	1. Is the saw powerful enough to turn a blade that size when cutting? 2. If you have a hand held saw then you might be binding the blade 3. Is the blade on backwards....i e wrong rotation
Question:	What is the return policy
Answer:	I've never had to return a blade, so I don't know - but I imagine it's probably like other Amazon items - easy!

• ✸FIT SIZE: Outer Diameter: 115mm (4.5 inch). Core: 22MM(Come with 20MM Ring). Thickness: 1.2mm. Suitable for most tile saws and hand-held angle grinders with a 7/8" and 4/5" Arbor.
• ✸COMPATIBLE MODELS: It can be used on different types of angle grinders and tile cutters for Wet and Dry cutting.
• ✸WIDE APPLICATIONS: Universal for dry or wet cutting. Adust diamond saw blade is engineered for extremely smooth cutting of porcelain, granite, marble, ceramic tile, etc. It will be a perfect partner for tile installers and general homemade DIYers.
• ✸HIGH PERFORMANCE: Super thin and unique X-style teeth for high performance, offer fast and smooth cutting. Thicker center to avoid vibrations and wobbling.
• ✸EXTREMELY RELIABLE: Thank you so much for your great support on us. Product quality and customer satisfaction is our top priority. But if you are not satisfied with your purchase or you have any questions, please feel free to contact us at any time. We're happy to help.

User questions & answers

Question:	What is the measurement of the mounting hole
Answer:	I can't see how a 93.5 inch blade could possibly fit a saw intended for a 95 inch one.
Question:	Is this blade suitable for cutting porcelain
Answer:	Great blade for me. Have used it on 1/2 up to 3 inch stock. Very steady.
Question:	Will this fit the Dremel tile saw
Answer:	Yes. The 137.224240 can be fitted with blades from 91.5" to 93.5" and 1/8" to 1/2".
Question:	what tools will this work with? An angle grider
Answer:	While I am unsure what "gir" is, this blade is excellent at resawing. I purchased it to resaw white oak into 3/16 x 1 1/2 strips for laminating frames for building a cruising sailboat. After about 500 feet I needed to clean the blade...but it remained sharp.

Product features

Diamond Saw Blade

Adust super thin diamond blades are designed for cutting porcelain, ceramic tile, granite, sandstone quartz, marble, brick, slate and cement backer board.It will be perfect partner for tile installer and general home made DIYers. Wear all applicable safety gear when using these discs (eyes/ears/face/hands/body/etc).

• Size: 4"/4.5"/5"
• Outer Diameter(mm): 105mm / 4 inch, 115mm / 4.5 inch, 125mm / 5 inch
• Segment Height: 10mm
• Core Thickness(mm): 1.2mm
• Rpm: 8000-11000
• Arbor: 7/8"-5/8" (22.23mm-20mm)
• Cutting: dry and wet cutting
• Application: Porcelain tile, Granite ,Marble,stone ,ceramic

Super Thin Diamond Saw Blade

1.2mm super thin turbo mesh rim design not only provides faster cutting, but also ensures a longer service life.Suitable for most tile saws and hand-held angle grinders with a 7/8" or 5/8" Arbor.

X Teeth Turbo Mesh Rim Design

X teeth design provides fast smooth precise clean excellent cutting performance. less dust, less vibration.which can bring higher work efficiency and economic benefits.

Universal For Dry or Wet Cutting

Universal For Dry or Wet Cutting.Using water when cutting with Adust Diamond saw blades, which helps the blades longevity.The water cools down the blade from heating and decreases the friction in the cutting zone by flushing out all the debris of the materials cut; it also reduces the dust produced from the cutting.

Product description

Products Name: Diamond Saw Blade

Package Quantity: 5Pcs

Material: Diamond and Metal

Size: Diameter 4"/105 mm,Inner hole 15.88mm

• Universal for dry or wet cutting.
• Super thin turbo mesh rim diamond blade provide fast, precise, smooth and chip-free cutting experience for you.
• Thicker center to avoid vibrations and wobbling. High Performance diamond matrix provides long life and enhanced material removal.
• Diamond blade can be used as porcelain tile blade, ceramia tile blade, granite blade and other thin masonry blade.
• Quantity:5pcs/Lot

User questions & answers

Question:	is this wet or dry
Answer:	Saw does not draw water ... used outdoor garden hose connected to the included hose adapter. You can turn water on/off with valve on saw.
Question:	can i print this ad page
Answer:	Hi Peter I just baughtbthis alpha saw 2 months ago to cutc1 1/4 granite slab it is nade by alpha tools in USA and it is a beast I had to call to CSR and they build and work in USA. Have fun with this tool its amazing
Question:	What is the arbor size and does it come with adaptor rings
Answer:	No, I would recommend the Flex wet saw. It lasts longer and does the 45 degree angle cuts.
Question:	Can this be used to cut stone tile
Answer:	No, solo hace cortes al hilo. No hace cortes de inglete.

Product description

Hot sintered continius rim turbo cutting ceramic saw blade matched with hand-held machine,and widely used for cutting porcelain tile, ceramic tiles, stonce prcess or construciton. . Universal for dry or wet cutting; . X teeth offer fast and smooth cutting; .Super thin porcelain saw blade with free chips for cutting

• Universal for dry or wet cutting.
• X teeth offer fast and smooth cutting.
• Super thin turbo mesh rim diamond blade provide fast, precise, smooth and chip-free cutting experience for you.
• Thicker center to avoid vibrations and wobbling. High Performance diamond matrix provides long life and enhanced material removal.
• Diamond blade can be used as porcelain tile blade, ceramia tile blade, granite blade and other thin masonry blade.

User questions & answers

Question:	Can I use this to cut a wine bottle
Answer:	Yes, it could be used for cut a little glass.
Question:	Will this fit on a dremel
Answer:	we don't think so our blade fit on dremel 3000 for you need to match right arbor.
Question:	Will this work with the dewalt angle grinder (model dcg413b) with arbor size
Answer:	It does have .625 arbor size but is intended to be used in a saw making straight line cuts. If you don't stay in a straight line it will bind and may damage the workpiece. I would not recommend using it in an angle grinder.
Question:	Does it works in angle grinder
Answer:	Won’t work on a 4” grinder.

Product description

Outer Diameter(mm):115mm /4.5 inch

Segment Height:10mm

Core Thickness(mm):1.2mm

Rpm:8000-11000

Quality:A class

Arbor:7/8"-5/8" (22.23mm-20mm)

Cutting:dry and wet cutting

Application:Porcelain tile, Granite ,Marble,stone ,ceramic





Our main products are diamond segments, saw blades, wire saws,diamond abrasive, flexible diamond polishing pad, floor polishing pads, cup wheels, profiling wheels, CNC-profiling wheels, drill bits, finger router bits, brushes, abrasive blocks and electroplated tools, with various specifications.

All these products have reached internationally advanced standard and are widely used for cutting, grinding or polishing granite, marble, concrete, asphalt, refractory, porcelain and glass.

All of our products are under strict quality control.

• Universal for dry or wet cutting
• X teeth offer fast and smooth cutting
• Super thin porcelain saw blade with free chips for cutting,Match with hand-held machine
• Available for cutting porcelain,ceramic tile,granite, sandstone quartz ect
• Size:115 x 10 x 1.2 x 22.23 mm,Thickness:1.2mm,Outer Diameter:115mm /4.5 inch.Suitable for most tile saws and hand-held angle grinders with a 7/8" or 5/8" Arbor.

User questions & answers

Question:	Can this cut through a concrete slab
Answer:	Yes, It can cut through the concrete slab easily.
Question:	Will this blade cut through roof tile that is approximately 1/2” thick
Answer:	Yes it will.like a hot knife cutting through butter. Get a hydro sponge same kind of sponge tile setters use.get some water on the sponge while your cutting let spong touch the side of the blade as your cutting.What this does is keeps the blade free of the fine dust and will also prevent small chipping of your roof tile..you will be impressed on how well these blades cut..make sure you use the sponge.if u don't what happens is the diamonds on the blade will get clogged up with fine dust and won't cut near as clean. Hope this info helps
Question:	will this cut glass
Answer:	This is not worth buying. The cutting edge is dangerous, as it separates when cutting
Question:	The Rubi blades of similar design are not designed to cut a radius according to the distributor I feel with. Are these
Answer:	The blue blades suck, the edge was chipping off after like4 or 5 cuts. Don’t waste your money. I bought 6 , still have 5. They are dangerous, not worth getting hurt. The red ones are awesome. Buy those Jerry

Product features

Universal For Dry or Wet Cutting

Universal For Dry or Wet Cutting

Using water when cutting with GoYonder Diamond saw blades, which helps the blades longevity.The water cools down the blade from heating and decreases the friction in the cutting zone by flushing out all the debris of the materials cut; it also reduces the dust produced from the cutting.

X Teeth Turbo Mesh Rim Design

X teeth design provides fast smooth precise clean excellent cutting performance. less dust, less vibration.which can bring higher work efficiency and economic benefits.

Super Thin Diamond Saw Blade

1.2mm super thin turbo mesh rim design not only provides faster cutting, but also ensures a longer service life.Suitable for most tile saws and hand-held angle grinders with a 7/8" or 5/8" Arbor.

Wide Application

GoYonder super thin diamond blades are designed for cutting porcelain, ceramic tile, granite, sandstone quartz, marble, brick, slate and cement backer board.It will be perfect partner for tile installer and general home made DIYers.Wear all applicable safety gear when using these discs (eyes/ears/face/hands/body/etc).

Product description

HIGH-TECH mesh turbo rim circular saw blade for cutting material like marble, tile. Designed with super-thin X rim to minimize material waste and achieves highest aggressiveness.

Package included:

5 x 4” diamond cutting blade(Comes with 4/5 inch(20mm) adapters)



Feature:

Super thin 1.2mm segments.

X Mesh Turbo teeth offer fast and smooth cutting.

High temperature extraction.

No Chipping for cutting.

Long service life.

For cutting porcelain, ceramic tile, granite, sandstone quartz, etc.



Note:

Please make sure your tool size before you purchase.

• 【SIZE】Outer Diameter: 105mm(4 inch). Thickness: 1.2mm.
• 【COMPATIBLE MODELS】Suitable for most tile saws and hand-held angle grinders with a 4/5" or 5/8" Arbor. It can be used on different types of angle grinders and tile cutters for Wet and Dry cutting.
• 【FAST & SMOOTH CUTTING】X teeth offer fast and smooth cutting. Thicker center to avoid vibrations and wobbling.
• 【HIGH PERFORMANCE】The Turbo-Mesh rim provides extremely smooth cutting finish on porcelain, marble, and ceramic tile. The Mesh rim design allows for less friction and more efficient heat dispersion. High-Performance diamond matrix provides long life and enhanced material removal.
• 【WIDE APPLICATION】It's designed for cutting porcelain, ceramic tile, granite, sandstone quartz, marble, brick, slate, cement backer board, etc. It will be a perfect partner for tile installers and general homemade DIYers.

User questions & answers

Question:	Does it fit makita 4” grinder
Answer:	This works best with a 4.5 angle grinder or 5" angle grinder
Question:	Will this cut 20mm outdoor porcelain please
Answer:	Yes, as long as it is a right-spin bey. The beys might fall off more frequently because it was not the original launcher, which is kind of annoying.
Question:	So is the bore size 16m without the spacer removed
Answer:	With 50 plus years of woodworking experience I would say that this should not cause any problems. Using this blade size for over a year on my saw, I have not had any problem at all. Cutting great.
Question:	What is the maximum RPM of the wheel
Answer:	Really depends on what you usually use the saw for. For woodworking, I always have a spare 1/8" fine tooth blade for intricate cuts, a 1/4' 6tpi skip tooth for general cutting and a 3/8"-1/2" 4-6 tpi for ripping available. Cool blocks are a great addition to any saw. Keep your tension right for each blade width and enjoy that saw!

Product description

This DeWalt tile saw blade is used to produce chip-free, clean cuts on a variety of hard, ceramic materials. The diamond matrix is designed specifically for wet applications as on a tile saw.

DeWalt Ceramic Tile Blades are designed with an optimized cutting matrix. The high diamond concentration provides for a faster cut rate while the high quality of the diamonds provide longer blade life. The consistent diamond distribution and concentration provide high performance. A high-quality steel core reduces distortion at high operating temperatures and also reduces the vibration.

From the Manufacturer

DEWALT tile saw blades are used to produce chip-free, clean cuts on a variety of hard, ceramic materials. The diamond matrix is designed specifically for wet applications as on a tile saw. DEWALT Ceramic Tile Blades are designed with an optimized cutting matrix. The high diamond concentration provides for a faster cut rate while the high quality of the diamonds provide longer blade life. The consistent diamond distribution and concentration provide high performance. A high quality steel core reduces distortion at high operating temperatures and also reduces the vibration.

• Extended performance diamond matrix provides long life and enhanced material cutting
• Continuous rim design provides chip free cutting in all types of tile
• XP2 and XP4 blades designed specifically for high power tile saws, allowing quick, free, low heat, and straight cutting
• XP2 and XP3 blades with laser cut expansion slots eliminate blade warping due to heat build-up
• Premium XP2 and XP4 cutting matrix means XP2 gives 2 x-feets the life of standard blades, XP4 gives 4x-feets the life of standard blades

User questions & answers

Question:	HAs anyone cut brick Pavers with this? Want to know how it does
Answer:	Made in China...
Question:	Will this cut glass bottles
Answer:	Any
Question:	what is the blade thickness
Answer:	Yes, it will work with an adjustable drill chuck...
Question:	Will this blade cut asphalt
Answer:	Not really，the drill bits are pretty tough，ceramics gone through just like woods.

Product description

Quality industrial grade diamonds and easy-to-use color coding system. Applications include cutting in ceramic, slate. For use in tile saw.

• 5/8-Inch arbor
• Designed for clean cuts in most tile materials
• Tensioned steel core for stability
• Consistent diamond content and even distribution

User questions & answers

Question:	Has anyone used this blade to sharpen carbide tipped combination blades
Answer:	What do you mean by bond
Question:	can this blade cut metal
Answer:	It will work fine for cutting wine bottle and the like (thicker glass). If you feed into the blade slowly you will get a smooth chip free cut. The thinner the glass being cut, the more prone to chipping and cracking it will be.
Question:	can I use this to cut agates and other stones
Answer:	The blade does not impact the voltage. It is the arbor (the hole in the center) that matters.
Question:	How does this do with porcelain tile? I see that they mention "slate and ceramic on the blade itself. All of my work it with porcelain
Answer:	The label on the blade says it's good to 6000 RPM. But you wouldn't be able to read the label until you buy the blade and you wouldn't buy it until you knew what it's RPM limit is. Glad to help!

Product features

Bosch Diamond Blades

All Bosch diamond blades start with a formulation that emphasizes consistent diamond content and even distribution. A hardened and tensioned steel core provides rigidity and stability during cutting; and blades are designed to extend the life and enhance user comfort. Bosch engineers develop custom combinations of metals and industrial-grade diamonds to produce blades for specific concrete- and masonry-cutting applications.

Segmented Rim

For the fastest cuts in concrete, block, brick and stone.

Turbo Rim

For fast, smooth cuts in concrete, masonry and stone.

Continuous Rim

The cleanest cuts, best for tile and stone.

Go the Distance

Bosch diamond blades are designed for tough professional applications.

Superior Performance

Delivers clean, accurate cuts in a variety of different abrasive materials.

Tuckpointing

Standard and sandwich tuckpointing blades provide quick and consistent grout and mortar removal.

Concrete Surfacing

Segmented and turbo diamond cup wheels are optimized for material removal and fine finishing applications.

• New Mesh Turbo Rim design increases cooling and dust extraction with minimal chipping.
• Supreme Grade diamond rim for fast cutting with long life on a wide range of materials including porcelain tile, ceramic tile, granite, marble, slate, terrazzo, engineered stone and similar materials.
• Specs are 7" diameter X .055 thick with a diamond-7/8"-5/8" universal arbor for use on all tile saws, circular saws and hand-held grinders. Wet cutting.The extra thick reinforced core is made from heat-treated hi-speed steel.
• Super Thin (.055) cutting rim greatly improves cutting performance and results in first-class cuts!
• This diamond blade has a lifetime warranty with free return shipping. If it ever breaks, warps, cracks or shows any indication of a material defect (being used for its intended purpose), or if the bond between the diamond segment and the steel core becomes separated at any time, it will be replaced free of charge!

User questions & answers

Question:	will this blade fit my dewalt wet saw
Answer:	Yes, they provide 7/8" arbor and 2 rings to change to other size.

Product features

Cyclone Supreme Super Thin Diamond Saw Blade for Cutting Porcelain Tiles, Granite, Marble, & Ceramics for use with Tile Saws, Angle Grinders and Circular Saws

Delta Diamond's Cycle Supreme Super Thin Diamond Blades offer a new mesh turbo rim design that increases cooling and dust extraction with minimal chipping. The extra thick reinforced core is made from heat-treated hi-speed steel to provide extra stability for extra hard materials.

Product description

Porcelain Saw Blade 4in

Size:4"(105mm)

Arbor:7/8"-5/8"

Segment Height:10mm*1.2mm

• Package 3pcs.
• Universal for dry or wet cutting.
• X teeth offer fast and smooth cutting.
• Thicker center to avoid vibrations and wobbling. High Performance diamond matrix provides long life and enhanced material removal.
• Diamond blade can be used as porcelain tile blade, ceramia tile blade, granite blade and other thin masonry blade.

Product description

The beast porcelain tile blades are designed to cut porcelain, Marble, Granite, and ceramic tiles. The thin kerf cutting edge allows for a clean, fast cut with virtually No chipping. The beast porcelain tile blades are engineered with a reinforced silent core hub which ensures straight cuts and greatly reduces noise.

• CONTINUOUS RIM CONFIGURATION – For clean and precise cuts wet cuts of porcelain and stone tiles
• EXPERT DESIGN – The thin Kerf cutting edge eliminates chipping while cutting. The beast porcelain tile blades are engineered with a reinforced silent core hub which ensures straight cuts and reduces noise. Intended to cut porcelain,, marble, granite, an ceramic tiles
• BUILT FOR THE PROFESSIONAL – This is the ideal diamond saw blade for tile workers, construction workers, carpenters, general contractors, serious DIYers, and tradesmen
• EQUIPMENT – Designed to be used on hand grinders, circular saws, hand held saws and chop saws
• WET SAW BLADE – For wet use only

User questions & answers

Question:	HOw long did the blade last cutting porcelain tiles? DOes it make clean cuts
Answer:	YES, it's standard 16mm bore.
Question:	This is a 5/8 harbor
Answer:	12000
Question:	Does it really work
Answer:	It can be 5/8 or 7/8.
Question:	How thick is the blade (kerf
Answer:	yes

Product features

About Lackmond

For over two decades, Lackmond has provided high-quality professional diamond tools for cutting, drilling and grinding to meet the needs of today’s most demanding markets. From our modest beginning as Lackmond R&D to our evolution as Lackmond Products, Inc. in 1994, our name has been synonymous with high quality diamond products. Our commitment to research and development is unmatched; we continually test new diamonds and powders to ensure our products exceed your expectations. Our product portfolio offers a wide range of diamond tools and equipment including: saw blades, core bits, grinding wheels, tungsten carbide saw blades for wood and metals (ferrous and non-ferrous), high quality German carbide drill bits, concrete saws, tile saws, core drill rigs, and much more.

BEAST Pro

Hard Porcelain.

Product description

DEWALT DW4701 Industrial 4-1/2-Inch Dry or Wet Cutting Continuous Rim Diamond Saw Blade with 7/8-Inch Arbor

The DEWALT DW4701 is a great addition to your 4-to-4-1/2-inch grinders. With an advanced diamond matrix, this blade provides a longer life and improved grinder application. It’s designed for consistency, with a straight and dependable depth of cut and a greater life span by 100 times more than the industry standard. Use this blade on a variety of tough applications, including concrete, stone, granite, brick, and tile. It measures 4-1/2-inches in diameter with a 5/8-inch and 7/8-imch arbor. This grinder accessory must be used with the DW4705 4-inch or 4-1/2-inch guard with show and the DW4717 4-inch flange or DW4706 4-1/2-inch flange.

From the Manufacturer

DEWALT DW4701 Industrial 4-1/2-Inch Dry or Wet Cutting Continuous Rim Diamond Saw Blade with 7/8-Inch Arbor

• Extended performance diamond matrix provides 350 times the life of conventional abrasives
• Ideal addition to 4-to-4-1/2-inch grinders
• Continuous rim turbo design provides optimal use in brick, block, and tile
• Large diamond segments with cobalt ideal for use across various product applications
• Works with concrete, stone, granite, brick, and tile

User questions & answers

Question:	will it cut threw I beams
Answer:	No
Question:	Will this blade cut granite,corian,marble and ceramic tile
Answer:	For the blade to function properly no water is needed but should wear a good mask and safety goggles because substantial cement dust is generated.
Question:	Can this blade, eith a 7/8" arbor be used with the d28402 grinder which has a 5/8" arbor
Answer:	Yes
Question:	According to specs -Works with concrete, stone, granite, brick, and tile. Will this blade cut metal
Answer:	Yes, cuts most any type of stone countertops. Go slowly to avoid chipping the edge.

• Dry or wet cutting,with 1"-20mm-5/8" arbor
• Designed for cutting porcelain tile ceramic granite marble brick ect
• Our delivery time is about 7-15 days from China
• Super Thin X Turbo Segments provide chip free cutting
• Reinforced ring core on both side of blade, make cutting more stable and get better finishing

User questions & answers

Question:	Does the 10inch blade include a 5/8th arbor washer? The images only show a 1 and a 7/8th arbor option
Answer:	This blade was meant for stone/tile type materials, but if you have a light gauge metal (wire mesh/alum siding) it will probably do in a bind. But I would not recommend it for heavy gauge metals (steel door/iron bars etc; you will need a metal cutting blade instead).
Question:	Can it be used to cut wine bottles
Answer:	You sure can, granite is no problem and that's about as hard as stone's get. Cuting thick stuff make sure you use it wet, dry cuts on thick stuff will wear it out a lot quicker but it'll last a long time cutting with water.
Question:	does this blade come in with a 1 inch arbor
Answer:	I have used it with both ceramic and porcelain tile and it worked well with both.

Product features

Suitable for Dry/Wet Cuts

• Blades are made of high hardness turbo diamond Segment and high-strength steel with multi-hole design,
• which could enhance heat dissipation, chip removal and reduce noise,
• You could use them in Dry/Wet Condition

Super Thin X Turbo Teeth Design

• Super Thin X Teeth Turbo design not only provides faster and smooth cuts, but also ensures chip fee cuts with less dust and longer working life,
• which can bring higher work efficiency and economic benefits

Reinforced Ring Core

• Both sides of Blades contain Reinforced Ring Core, which could make cutting more stable and get better finishing
• With the bore of 1"-20mm-5/8", suitable for most tile saws with 1"-20mm-5/8" arbor

Wide Application

• Designed for cutting Porcelain/Tile/Ceramics/Brick/Granite/Marble/Rock/Masonry/Quartz/Stones/Slate/Cement/All Similar Materials.

• Suitable for tile installer and general home made DIYers, Please wear all applicable safety gear when using these discs (eyes/ears/face/hands/body/etc).