12 best skar audio amps for cars

Product description

The Skar Audio SKv2-1500.1D is a competition grade monoblock class D subwoofer amplifier that was designed to deliver unequivocal performance and power output. As a part of the flagship SKv2 series of amplifiers from Skar Audio, this model utilizes only the highest quality internal components and features advanced engineering enhancements that allow it to outperform anything else on the market in its power class.



Whether you are competing in the SPL lanes, or looking for the absolute best amplifier to power your "daily driver" audio system, look no further - this is the amplifier for you. The SKv2-1500.1D is conservatively rated at 1,500 Watts RMS power, and at max power output can produce more than an astonishing 2,200 watts. In addition to its extreme performance capabilities, this amplifier features an advanced heatsink design that allows for maximum cooling, as well as 4-way protection circuitry, enabling the amplifier to operate efficiently at peak output levels for hours on end.



Furthermore, you'll have full reign over your amplifier with the built-in user control panel, featuring variable adjustment tunings for gain level, subsonic filter, bass boost, low-pass filter, and phase control. Versatility is key, and so you have the ability with the SKv2-1500.1D to run them strapped if desired, which is unique to our SKv2 series of amplifiers. In addition to all the above features, it also has both RCA inputs and outputs so that you can easily daisy chain multiple amplifiers together, and utilizes massive 1/0-gauge power and ground input terminals which allow for maximum current flow and therefore higher power output.



This amplifier comes with a remote subwoofer level control (bass knob) allowing the user to have full control over their bass from the front of the vehicle.

• Competition Grade SPL Class D Monoblock MOSFET Car Power Amplifier
• Peak Power at 1 Ohm: 2,200 Watts | RMS Power at 1 Ohm: 1,500 Watts
• Stable at 1 Ohm, Frequency Response: 15Hz - 270Hz
• Featuring 4-Way Protection Circuitry and 1/0 Gauge Power & Ground Input Terminals for Maximum Current Flow
• User Adjustable Low Pass Filter (Variable): 35Hz - 250Hz, Remote Subwoofer Level Control Included
• Heavy Duty Advanced Heatsink Design Allows for Maximum Cooling & Efficiency | On-board Bass Boost Control (0-9dB)

User questions & answers

Question:	Has anyone ran the skv2 1500.1 at .5 ohms and not blown it up
Answer:	Yes, this amp is shouldn't be your concern. I'd be worried about those 6x9s handling this amp. I say that because though I really like Skar I've had no luck with their 6x9s. Good news is I haven't owned these sk 6x9s so you may be in luck. This amp is powering a pair of audiopipe CSL-6904 6x9 & a pair of Infinity KAPPA-93iX 6x9s in my car with a Skar EVL-15 pushed at 1 ohm with an audiopipe 1500w monoblock & fixing to strap it. The clarity of the 6x9s are wonderful at any level.
Question:	Is this amp good for a kicker 15 inch L7 solar boric dual voice coil at 4 ohms
Answer:	This is a class A/B 4 channel amp. It works great in your application.
Question:	Will these power dual skar audio d
Answer:	Well i dont think it has on board fuses like other amps.. I think higher power amps need an external fuse block to be put in the wire near the amp.. Im no expert tho.. But i would have both the fuse near the battery and near the amp match... Do some more research on the net to make sure you dont have a fuse too big or too small
Question:	Will this work for a sp audio sp12cx dual 2 ohm at 2500 rms? or should i get the skv2 2500 1d
Answer:	I currently run six on just 2 channels. Pay attention to the ohm load and properly set gains with a multimeter prior to playing.

Product description

The Skar Audio RP-75.4AB is a powerful, efficient, and highly reliable four channel class a/b full-range car amplifier. Capable of powering an entire aftermarket upgraded speaker system in a vehicle, it packs the power that will allow you to get loud and let your speakers come alive. Featuring a high speed MOSFET power supply, premium grade internal components, as well as 4-way protection circuitry, the amplifier will operate at the highest levels of performance for hours on end safely. With a depth of adjustable user controls such as the gain, lpf, hpf, crossover, and bass eq, this amplifier is extremely versatile and can be used in so many applications. These advanced user controls will allow you to dial your sound in exactly as you want for perfect clarity, whether running active components or speakers with in-line crossover networks. The class A/B circuitry design of this model allows it to amplify your audio signal with maximum clarity and sound excellence, all while being extremely efficient. Features 8 gauge power and ground input terminal connections for maximum current flow.

• 500-Watt MOSFET 4-Channel Class A/B Power Car Amplifier
• RMS Power at 2 Ohms: 125 Watts x 4 Channels
• RMS Power at 4 Ohms: 75 Watts x 4 Channel
• User Adjustable Controls: Gain, Variable LPF, HPF, Bass EQ Switch (0, +6, +12 dB)
• 4 Way Protection Circuitry | Frequency Response: 20 Hz - 20,000 Hz
• Signal to Noise Ratio: 105 dB

User questions & answers

Question:	Will this amp power 4 skar audio sk 6x9s good i got 2 skar audio vvx 15s on a skar rp 2000.1d and i don’t want the bass to drown out the voice
Answer:	It’s close to 2 feet long.
Question:	Would this amp be appropriate for skar audio vxi65 360-watt 6.5" 2-way component speaker system
Answer:	Not on this model amplifier. The 1 and 2 channel skar audio amplifiers come with a bass nob.
Question:	What size fuse this amplifier carry
Answer:	Yes if you wanted to. You just leave the other channel open. Or use channel 1 and 2, then bridge channel 3 and 4.
Question:	Can i run 8 speakees on this
Answer:	I really don't know, however, this thing is a beast! Running 4 six inch JL marine speakers in my boat and only using 150 watts/ channel. Very clean and awesome volume in an open cockpit. Just purchased 4 Skar speakers, an 8" sub and 5 channel for my camper, all Skar Audio.. very happy with the performance and love the low cost

Product description

Skar Audio engineered the SKA7EQ 7 band 1/2 DIN car audio graphic equalizer so that you can finally take full control over your car audio listening experience, dialing the sound into perfection. Featuring two sets of RCA inputs (main and a selectable auxiliary input), this EQ takes your input signal and allows you to modify and adjust the sound to your liking. The output signal is then delivered via the high voltage (up to 7V max) pre-amp RCA outputs for the Front, Rear, and Subwoofer channels (the subwoofer out-put channel features an independent volume control knob on the front of the unit as well). 7 fully adjustable -12 dB to +12 dB EQ bands (50 Hz, 125 Hz, 320 Hz, 750 Hz, 2. 2 kHz, 6 kHz, 16 kHz) with built-in fader control.

• 6 Channel 7-Band High Performance Car Audio 1/2 DIN Pre-Amp Electronic Equalizer
• Featuring 2 (Balanced & Selectable) RCA Inputs - Main and Auxiliary (Aux w/ Variable Gain Control) | THD: 0. 005%
• High Voltage (Max Output Voltage - 7V) Gold Plated Pre-Amp RCA Outputs - Front, Rear, and Subwoofer (with Variable Subwoofer Level Control on Front of EQ)
• 7 Fully Adjustable -12 dB to +12 dB EQ Bands (50 Hz, 125 Hz, 320 Hz, 750 Hz, 2. 2 kHz, 6 kHz, 16 kHz) with Built-in Fader Control
• Take Full Control Over Your Car Audio System with this EQ | Signal-to-Noise Ratio: 100 dB, Low Pass Frequency Switch: 60 Hz / 120 Hz
• Includes Installation Mounting Brackets and Hardware | 20 dB Headroom Eliminated Signal Overload
• Included components: Installation Brackets and Hardware

User questions & answers

Question:	How would you wire this to a head unit that has a front, rear and subwoofer channel? Would you only use the front and rear and toss the other set of r
Answer:	So with only one input from the head unit does the eq convert it to front and rear sound? What I mean do you loose the rear sound or does it just double and split the front channel?
Question:	Does this product light up
Answer:	Yes it lights up blue cleaned up my audio very well
Question:	Anyone els experiencing a popping noise when you take key out ignition if so any ideas on how i can stop it? I already tried grounding it to radio
Answer:	Had the same issue with ankther brand EQ. Problem went away when I switched the positive from the EQ and attached it to the yellow cable straight to battery not the red to ignition. That should fix it.
Question:	How would you do the power wire i see theres one in picture with a fuse but isint that to short
Answer:	Hello, No the Red wire with fuse holder is not to short. The longer side of the Red wire goes to the Scar SKA7EQ, On Back of the SKA7EQ is the power, ground, and Remote terminal. The Red wire will be extended with a 14awg wire to your power source. Source could be the car battery, or an Accessory fuse circuit of 10 amps 12volts DC current. Extending this red wire is Normal in the audio installation world. The coupling will be needed to successfully butt the two wires together and crimp both sides, if u like install the double red wire size with Heat Shrink Tubbing, then Couple the wires with the "Butt Connector" , slide the heat shrink over it and heat the heat shrink with a Heat Gun, or powerfully hair dryer, then run the Red wire to the Accessory, or Battery positive Red Terminal. The same thing for the ground wire, black wire has no fuse in line so Run from your battery Negative Terminal Black, to the Scar SKA7EQ next to the Red wire, and Tighten it down to the SKA7EQ. The Remote wire is "In the business of Audio Installation" Traditionally Blue, Or Purple, Strip 4mm, or 3/8" and Install it into the Scar SKA7EQ at the R terminal, R stands for "Remote" or "Trigger" this Blue, Or Purple wire goes to your amplifier, and at the amplifier you will see a Positive terminal, a Negative Terminal and the R, "Remote" terminal the Blue or Purple Remote wire tightens onto the amp in the R terminal spot. The wire should be all 14 AWG for this. Wiring your amps u should at least use 4awg for both Power and Ground, Directly to the car/boat/atv Battery. Use small spools of OFC Copper, Red Positive, Black Negative, and Blue/Purple Remote from amazon, You have to have Amplifiers in your system to use the SKA7EQ. Get an Amplifier install kit, plus the three spools of 20ft of 14 AWG Red, Black, Blue from amazon....Good Luck.

Product description

Scar Audio engineered the RP-1500.1DM marine amplifier to be unrivaled in both performance and reliability compared to anything else on the marine market its' class. Designing the most efficient, well built, high quality amplifiers is where we start here at Scar Audio, and that is exactly what is delivered in the RP-1500.1DM. The RP-1500.1DM is 1-ohm stable and utilizes a wide array premium internal components that make it extremely powerful and reliable - such as its high speed MOSFET power supply and advanced, marine grade, PCB board layout. Conservatively rated at 1,500 watts RMS power at a 1-ohm load, with the capabilities of reaching beyond 2,300 watts at max power output, this amplifier is great for powering the sub stage on your boat/UTV. Furthermore, the oversized 4-gauge power and ground terminals found on the amplifier allow for maximum current flow and therefore higher power output and more efficient operation. You'll have full reign over your amplifier with the built-in user control panel, featuring a bass EQ switch (0, +6, +12dB), and variable adjustment tunings for gain level, low-pass filter, and subsonic filter. In addition to all the above features, this model also features 4-way protection circuitry, which will give the user the peace of mind knowing they are protected against damage to the amplifier for various reasons - including electrical shortage, overheating, low voltage, and more. Our marine amplifiers feature a special marine coating internally that allow them to withstand the harshest conditions for long lasting use. This amplifier comes with a remote subwoofer level control (bass knob) allowing the user to have full control over their bass from anywhere on the watercraft.

• Marine Class D MOSFET Monoblock Power Amplifier
• Peak Power at 1 Ohm: 2,300 Watts | RMS Power at 1 Ohm: 1,500 Watts
• Fully Marini zed with Waterproof Coating on Circuit Board & Rust Proof Painting on Mechanical Case
• Frequency Response: 20Hz - 250Hz, On-board Bass EQ Switch with +6 or +12dB boost at 45Hz
• Featuring 4-Way Protection Circuitry and 4 Gauge Power & Ground Input Terminals for Maximum Current Flow
• Stable at 1 ohm | Remote Subwoofer Level Control Included
• Highly Efficient Heatsink Design allows for Maximum Reliability & Performance

User questions & answers

Question:	Where is the 80hz mark on the Lp filter and the 20 onthe subsonic filter
Answer:	Of course, it is compatible
Question:	Is it bridgable
Answer:	No it doesn’t have anything to hold it shut. It isn’t magnetized either. When I carry it I just put my hand around the whole thing.
Question:	Will this work well on my single 18 skar sdr 1200 watt 1 ohm sub
Answer:	Save your money, these covers are prone to fail. I bought 3 in span of 2 years. All 3 failed, either keyboard stopped working or the shell cracks unable to hold the ipad.
Question:	whats the diffrence between this and a car amp? can i put this in my car
Answer:	Model ML0V2LL/A I have a 12.9 iPad Pro and it fits perfectly...but it is in Spanish not English so some of the keys are a bit odd for me...

Product description

The Skar Audio EVL-12 D4 12" dual 4-ohm subwoofer redefines the conception of low-end sound reproduction. The engineering that went into developing the EVL series is simply amazing, and it shows in the sound quality and performance that this subwoofer demonstrates. The EVL Series can deliver incredibly accurate and powerful bass, due to a variety of advanced design features that make this subwoofer unique and in a class of its own.

Conservatively rated at 2,500 watts peak power, the EVL-12 D4 features a massive high flux, double stack ferrite motor structure - which delivers the driving force behind the tremoring lows this subwoofer can produce. Combine the motor with the black coated 3" high temperature voice coil of this driver, as well as the advanced air flow cooling design of the basket, and it quickly becomes evident why this woofer is capable of being played at the highest levels of output for hours on end.

Furthermore, the high roll foam surround incorporated into the design of this subwoofer is one of the reasons it can produce those ultra-low-end frequencies with such responsiveness. The suspension design of this subwoofer features the EVL's signature red, single damper, two-layer spider - which connects to the coil former with premium stitched lead wires. All these incredible features make this EVL subwoofer the unequivocal choice when looking for a high-quality car subwoofer.

Dual 4-ohm voice coil impedance, Peak Power: 2,500 Watts, RMS Power: 1,250 Watts, Frequency Response: 25-250 Hz, Sensitivity: 85.3 dB Fs: 40 Hz, Xmax: 23.5mm (one-way). Subwoofer Mounting Depth: 7.75", Subwoofer Cut-Out Diameter: 11.25".

• Peak Power: 2,500 Watts | RMS Power: 1,250 Watts
• 3" High Temperature Dual 4-ohm Voice Coil with Black Coating
• Competition Grade Paper Cone & High Roll Foam Surround | Fs: 40 Hz
• Premium Suspension Featuring the EVL Series Signature Red Two Layer Spider
• Deep, Low, Extremely Responsive Bass | Sensitivity: 85.3 dB
• Frequency Response Range: 25 Hz - 250 Hz | Xmax: 23.5 mm (one-way)

User questions & answers

Question:	Will these work in a dual cp212-w0v3 box without hurting the subs or box
Answer:	my ipad is Air 2 and itsin English
Question:	Will 2 of these handle a taramps 5k at 1ohm
Answer:	If it has smart connector on it yes. (Look on bottom of iPad). Check all pictures on Amazon to see it.
Question:	What is the mounting depth on a 10in
Answer:	Yes.
Question:	I want to buy 2 of these subwoofers, should i get Dual 2 ohm or 4 ohm? And whats the true rms for these subwoofers
Answer:	yes, it can works with iPad Air 3 10.5" 2019

Product features

Product Specifications

• Dual 4 Ohm Voice Coil Configuration
• Peak Power: 2500 Watts
• RMS Power: 1250 Watts
• Competition Grade Pressed Paper Cone
• 3" High Temperature CCAW Voice Coil
• Frequency Response: 25 Hz - 250 Hz
• Sensitivity: 85.3 dB
• Xmax: 23.5 mm
• Mounting Depth: 7.75"

Product description

Skar Audio designed the SDR-1X12D2 loaded subwoofer enclosure package for those who seek ultimate performance in subwoofer-bass fidelity. This package offers a simplified option to add a competition-grade subwoofer system, without the guesswork involved in designing it from scratch. The custom enclosure features one, SDR-12 D2 subwoofer, which is pre-loaded and wired up inside of a custom single 12" vented enclosure. We also include the perfect amplifier in this package to power your new subwoofer with the Skar Audio RP-800.1D, which comes with a premium 4 gauge amplifier wiring kit to make installing the amplifier hassle free. This custom enclosure used in this package was engineered by Skar Audio specifically for the subwoofer that is loaded in it, ensuring perfect sound and compatibility. Every subwoofer is different, and it is so critical when buying a subwoofer to ensure that the subwoofer and enclosure are an ideal match, or you will lose sound quality and output. The enclosure features a unique kerf port design, allowing for extreme levels of bass output. Furthermore, the enclosure is finished in premium grade black carpet for a sleek appearance and features the Skar Audio logo in white on the top surface of the box. The subwoofer comes pre-wired and loaded inside of the enclosure allowing for an easy and hassle free installation. The dual 2-ohm woofer is wired up inside of the enclosure so that the final impedance load is configured for 1-ohm at the terminals.

• All-in-One Complete SDR Series Loaded Subwoofer Complete Bass Package
• Peak Power: 1,200 Watts, RMS Power: 600 Watts
• Includes x1 Skar Audio SDR-1X12D2 Single 12" Loaded 1,200 Watt Vented Subwoofer Enclosure
• Includes x1 Skar Audio RP-800.1D Class D 800 Watt Monoblock Amplifier
• Includes x1 Skar Audio SKAR4ANL-CCA 4 Gauge Complete Amplifier Wiring Kit

User questions & answers

Question:	Would this fit somewhere in my 2004 Chevy Silverado 2500hd duramax without taking up more than one seat
Answer:	Yes
Question:	How many channels does the amp have
Answer:	I’d say anywhere for 18 to 20 gauge it’s very thin but haven’t had a problem with this kit
Question:	Does this include a remote subwoofer volume control
Answer:	No, you have to have a large gauge crimper.
Question:	Does this fit in my 2015 Honda Accord
Answer:	I know this post is from 2 months ago. But you need to figure everything in RMS wattage. Not Peak. I have a SKAR 1200.1. 1200 watts RMS but it hits abt 2500 peak on the amp Dyno@1ohm. This kit is adequate for my setup. This kit is OFC. 2500 watts RMS no but if your amp is 2500 peak. Yes this is enough. Also depends if your amp is class B or a Class D amp. Class D Amps are abt 75% efficient Total RMS wattage divided by 0.75 then divided by 13.8 gives your total current draw of your amp. If you have a class A/B change that number to 0.50 and do the same calculation. A good rule of thumb. Take the fuse ratings on your amp and add them up. Multiply by 10 and that’s usually your real RMS not what is advertised on the amp. If it has no onboard fuse the owners manual will tell you the recommended fuse size and multiply that by 10. I’d say this 17 foot kit would be fine 1200-1500 Watts RMS. If it’s closer to 1500 watts just buy a 150 AMP fuse for this kit on amazon for 4-5$ and you should be good. Always rake distance into account too. 16-18ft of 4 gauge OFC is fine. But if you go over 18ft you need 2 gauge or 0 gauge.

Product description

Skar Audio created this custom loaded enclosure package to deliver powerful, deep, and tight bass in an all-in-one competition-grade system. This package features two, 12-inch, dual 4-ohm, Skar Audio SDR Series subwoofers, which are pre-loaded and wired up inside of a custom dual 12" ported enclosure. Next, we pair the loaded enclosure of this package with the Skar Audio RP-1200.1D Class D mono-block amplifier, the perfect amplifier to power your new system and matched for perfect compatibility and power handling with the included subwoofers. Finally, we include a premium Skar Audio 4 Gauge OFC premium amplifier wiring kit to install your new system, making installation hassle free. The Skar Audio SDR series of subwoofers were designed to deliver hard hitting, low spectrum sound. Featuring a high flux ferrite motor, these versatile 12-inch woofers are conservatively rated at 1,200 watts max power each. When looking for a system that delivers low end frequencies with authority, look no further. This is the perfect solution for a daily driver that can handle whatever is thrown at it, offering unmatched reliability and sound quality. The enclosure housing the subwoofers features a unique kerf middle port and split chamber woofer design, allowing for extreme levels of bass output. Furthermore, the enclosure is finished in premium grade black carpet for a sleek appearance and features the Skar Audio logo in white on the top surface of the box. This package was put together by our installation experts to ensure compatibility and allow for an easy installation. We take the guess work out of pairing the components of your system up, and make it easy to get the bass you've always wanted in your ride.

• All-in-One Complete SDR Series Loaded Subwoofer Complete Bass Package
• Peak Power: 2,400 Watts, RMS Power: 1,200 Watts
• Includes x1 Skar Audio SDR-2X12D4 Dual 12" Loaded 2,400 Watt Vented Subwoofer Enclosure
• Includes x1 Skar Audio RP-1200.1D Class D 1,200 Watt Monoblock Car Subwoofer Amplifier
• Includes x1 Skar Audio SKAR4ANL-OFC 4 Gauge Premium OFC Complete Amplifier Wiring Kit

User questions & answers

Question:	Will this fit in a 2017 ford GT
Answer:	That one I'm not to sure on. But ford GT, nice... You could stop by and we can check it out...lol. Good luck.
Question:	Will this fit in a 2020 hyundai sonata trunk
Answer:	It will if your trunk is 40”wide by 20”deep and 16” tall
Question:	will it fit in a 2006 altima
Answer:	Yes
Question:	Will it fit in a 2005 double cab Tacoma
Answer:	I would say yes. But will not leave much room at all.

Product description

Skar Audio designed the sdr-1x10d2 complete loaded Subwoofer Enclosure bass package for those who seek ultimate performance in subwoofer-bass fidelity. The custom enclosure features one, SDR-10 D2 subwoofer, which is pre-loaded and wired up inside of a custom single 10" Vented enclosure. We also Include the perfect amplifier in this package to power your new subwoofer with the Skar Audio RP-800.1D, which comes with a premium 4 gauge amplifier wiring kit To make installing the amplifier hassle free.

• All-in-one complete SDR series loaded Subwoofer complete bass package
• Peak Power: 1, 200 watts | RMS Power: 600 watts
• Includes x1 Skar Audio sdr-1x10d2 single 10" Loaded 1, 200 watt vented subwoofer enclosure
• Includes x1 Skar Audio rp-800.1D class D 800 watt mono-block amplifier
• Includes x1 Skar Audio skar4anl-cca 4 gauge complete amplifier wiring kit
• Included Components: X1 Skar Audio Sdr-1X10D2 10-Inch Loaded Subwoofer Enclosure;X1 Skar Audio Rp-800.1D Class D Monoblock Subwoofer Amplifier;X1 Skar Audio Skar4Anl-Cca 4 Gauge Amplifier Wiring Kit

User questions & answers

Question:	I bought the 10 inch sub package. Where should the subsonic level be set? Is the box tuned enough for the sub to leave it set at zero
Answer:	No, it only works with the smart connector on the 9.7” iPad Pro.
Question:	How long does it take this order to ship
Answer:	I have owned this keyboard since the iPad released and I can say the following. It is a fantastic, spillproof, relatively quiet if not silent if you do not type fast and hard, and super slim keyboard attachment to your iPad Pro. It feels great to type on. Very strong magnet stays attached to the iPad, has never fallen off or failed to hold the weight even if held upside down. The one thing I will say that is negative is this. After all this time, either with an update, or just something faulty between the connection of they keyboard and the iPad, I keep getting a pop up error when they are connected (at times) saying accessory not recognized. This shouldn’t take away from 2 years of a almost perfect keyboard. Just thought I would mention it. 100% recommend it.
Question:	Does this amplifier have a high level input or do I need to purchase a separate converter to use with my stock radio
Answer:	Yes! This is one of the best cases for the iPad pro. It's protected all the way around the iPad and, when closed up, is secure and protected 100%
Question:	Will heat humidity deteriorate this sub
Answer:	realy dont know. I have not one iPad 6th to try it on

Product features

Product Specifications

• Includes Subwoofer Pre-Loaded Into Subwoofer Enclosure
• Skar Audio SDR-10 D2 - 10" Dual 2 Ohm Subwoofer
• Peak Power: 1,200 Watts
• RMS Power: 600 Watts
• Frequency Response: 30 - 300 Hz
• 2.5" Hight Temperature Copper Voice Coil

Skar Audio RP-800.1D Monoblock Amplifier

• Max Power @ 1 Ohm: 1,200 Watts x 1 Channel (14.4v)
• RMS Power @ 1 Ohm: 800 Watts x 1 Channel (14.4v)
• Working Voltage: 8.5V - 14.4V
• 4 Gauge Power and Ground Terminals
• MOSFET Power Supply
• Remote Bass Knob & Wire Included
• 4 Way Protection Circuitry: Thermal, Voltage, Speaker, DC
• Fuse Rating: 80 Amp
• Dimensions: 11.75" (Length) x 6.25" (Width) x 2.25" (Height)

Product description

Skar Audio created this custom loaded enclosure package to deliver powerful, deep, and tight bass in an all-in-one competition-grade system. This package features two, 10-inch, dual 4-ohm, Skar Audio SDR Series subwoofers, which are pre-loaded and wired up inside of a custom dual 10" ported enclosure. Next, we pair the loaded enclosure of this package with the Skar Audio RP-1200.1D Class D mono-block amplifier, the perfect amplifier to power your new system and matched for perfect compatibility and power handling with the included subwoofers. Finally, we include a premium Skar Audio 4 Gauge OFC premium amplifier wiring kit to install your new system, making installation hassle free. The Skar Audio SDR series of subwoofers were designed to deliver hard hitting, low spectrum sound. Featuring a high flux ferrite motor, these versatile 10-inch woofers are conservatively rated at 1,200 watts max power each. When looking for a system that delivers low end frequencies with authority, look no further. This is the perfect solution for a daily driver that can handle whatever is thrown at it, offering unmatched reliability and sound quality. The enclosure housing the subwoofers features a unique kerf middle port and split chamber woofer design, allowing for extreme levels of bass output. Furthermore, the enclosure is finished in premium grade black carpet for a sleek appearance and features the Skar Audio logo in white on the top surface of the box. This package was put together by our installation experts to ensure compatibility and allow for an easy installation. We take the guess work out of pairing the components of your system up, and make it easy to get the bass you've always wanted in your ride.

• All-in-One Complete SDR Series Loaded Subwoofer Complete Bass Package
• Peak Power: 2,400 Watts
• RMS Power: 1,200 Watts
• Includes x1 Skar Audio SDR-2X10D4 Dual 10" Loaded 2,400 Watt Vented Subwoofer Enclosure
• Includes x1 Skar Audio RP-1200.1D Class D 1,200 Watt Monoblock Car Subwoofer Amplifier

User questions & answers

Question:	Do i need a second battery for this amp
Answer:	[email protected] they have been a great help to me will respond within 24 hours M-F
Question:	Does this come with a base adjustment knob
Answer:	Yes hp on works on the channel you switch it to channel 5 shouldn’t have that option

Product description

Skar Audio introduces the SDR-2X12D4 Dual 12-inch loaded Vented subwoofer enclosure to cater to the audiophile who wants a competition grade system in their Vehicle without all of the headache involved with designing it from the ground up. This loaded enclosure features two of our extremely popular SDR-12 D4 1, 200 Watt Max power subwoofers which combined come in at 2, 400 watts Max power for the pair. The subwoofers come pre-loaded and wired up inside of this custom dual 12" Ported enclosure, which features a unique kerf middle port and split chamber woofer design, allowing for extreme levels of bass output. Furthermore, the enclosure is finished in premium grade black carpet for a sleek appearance and features the Skar Audio logo in white on the top surface of the box. This enclosure was engineered by Skar Audio specifically for the subwoofers that are loaded in it, ensuring perfect sound and compatibility. Every subwoofer is different, and it is so critical when buying subwoofers to ensure that the subwoofers and enclosure are an ideal match, or you will lose sound quality and output. With this loaded Subwoofer Enclosure model, All of those concerns are eliminated, making it easier than ever to add powerful aftermarket bass to your vehicle. The dual 4 ohm subwoofers are wired up inside of the enclosure so that the final Impedance Load is configured for 1-ohm at the terminals (one terminal cup). peak power: 2, 400 watts, RMS power: 1, 200 watts. Enclosure Dimensions: Width: 37.875", Depth #1: 18.75" (Bottom depth), depth #2: 16.75" (Top depth), height: 14.25"

• SDR Series 12-inch Dual 4-ohm loaded Subwoofer Enclosure
• Peak Power: 2,400 Watts | RMS power: 1,200 Watts
• Pre-wired Internally for a 1 Ohm Final Impedance Load at the Terminals for an Easy Installation
• Custom Vented Enclosure Made of High Strength 5/8" MDF and Finished in Premium Black Carpeting
• Double Front Baffle (1.25") with Countersunk subwoofer design for Flush and Attractive Appearance
• Ported Enclosure Tuned at 32 Hz for Deep and Accurate Bass

User questions & answers

Question:	Will this fit in a 17 Chevy premier pushed to the back of the seats
Answer:	Hello. There is no mute setting. In the battery compartment there is a setting for how many beeps you would like when the alarm goes off (3-60) and a setting for how loud you want the beeps (low to high).
Question:	Will these fit in a 2008 dodge avenger
Answer:	There is a setting in the battery compartment for low to high. The highest setting is loud, so I would recommend it as a kitchen timer.
Question:	Would these fit in a 2017 honda civic ex-l
Answer:	First you can rotate clockwise,then zore counterclockwise to turn ring off.
Question:	Do these move lots of air
Answer:	This is very quiet. This is the most satisfying timer I have ever bought. I bought it for my eight-year-old son. He likes it very much. Because there is no noise to distract him

Product features

Product Specifications

• Includes Subwoofers Pre-Loaded Into Subwoofer Enclosure
• Skar Audio SDR-12 D4 - 12" Dual 4 Ohm Subwoofers
• Peak Power: 2,400 Watts (pair) | 1,200 Watts (each)
• RMS Power: 1,200 Watts (pair) | 600 Watts (each)
• Frequency Response: 32 - 300 Hz
• 2.5" High Temperature Copper Voice Coil

Product description

Engineered and designed in the USA by Skar Audio engineers, the VX35-ST 500 Watt 3. 5-inch high compression titanium bullet tweeters are unmatched in performance and sound. Sold as a set of 2, these bullet style super tweeters are so powerful you might think you're in a concert hall when hearing them for the first time. It doesn't stop there however, the accuracy of the high frequencies reproduced by these tweeters is unparalleled, making them the top choice among audio enthusiasts.

• 3.5-inch High Compression Titanium Bullet Super Tweeters
• Max Power: 500 Watts
• RMS Power: 300 Watts
• The Max power rating, for each tweeter is 250 Watts, for a total of 500 Watts.
• 1" High Temperature Kapton Voice Coil with In-line Capacitor Crossover
• Impedance: 4 Ohms and Frequency Response: 2.2K-20KHz

User questions & answers

Question:	is the mounting diamitor 3.5 inches
Answer:	Go direct to the amp but adjust the gain level.
Question:	Is the delivery timely
Answer:	Tweeters use a lot less power than the mids; running a 4 ohm speaker in parallel with a 4 ohm tweeter will give you a 2 ohm load - ON PAPER - but in reality the amp is mostly "feeling" the burden of the speaker. I've always ignored the ohm rating of tweeters, and just worry about the larger speaker load.
Question:	fits corolla
Answer:	Yes
Question:	Why is Amazon changing the due dates on delivery
Answer:	120 watts total not rms watts

Product description

Skar Audio introduces the SDR-3X8D2 triple 8-inch loaded vented subwoofer enclosure for those seeking extreme bass output in their car audio system but who are limited by space in their vehicle. Featuring three of the Skar Audio SDR-8 700 Watt dual 2-ohm subwoofers, this 2, 100 Watt max power loaded enclosure was engineered to get loud and low. Achieve head turning levels of bass output with this loaded enclosure and let size and space limitations be a thing of the past. The three dual 2-ohm subwoofers come pre-loaded and wired up inside of this custom triple 8" ported enclosure with a final impedance load of 1. 33-ohms to a single speaker terminal cup located on the backside of the enclosure. This competition grade ported enclosure was designed for ultra responsive, low end frequency response, with all three drivers utilizing a single large shared chamber that shares two advanced slot ports located on opposites sides of the rear of the enclosure. We engineer our products to not only sound great, but to stand the test of time - which is why we construct this enclosure out of only the finest grade medium density fiberboard (MDF). Furthermore, the craftsmanship and build quality of this enclosure are world class and exemplified top to bottom. One such example of this being a double front baffle for enhanced strength that also doubles as a design enhancement allowing the subwoofers to be mounted with a flush finish. Finally, the loaded enclosure is finished in a premium black carpeting that features the Skar Audio logo centered across the top surface of the box. Peak Power: 2, 100 Watts, RMS Power: 1, 050 Watts.

• 2, 100 Watt Max Power Triple 8" Loaded Vented Subwoofer Enclosure
• Features x3 8-inch SDR-8 D2 700 Watt Max Power Dual 2-ohm Car Subwoofers
• Enclosure was Engineered for Extreme Bass Output with it's Dual Slot Ports and Single Internal Subwoofer Chamber
• High Strength MDF Box Construction (5/8") with a Dual Layer (1. 25") Countersunk Subwoofer Baffle
• Ported Enclosure Tuned at 46 Hz for Deep and Accurate Bass
• Subwoofers are Pre-wired Internally for a Final Impedance Load of 1. 33 Ohms

User questions & answers

Question:	Can I get this with the 900 watt
Answer:	The keyboard only works for the iPad Pro 9.7” 2016 model. No it will not work for the iPad 6th gen.
Question:	What’s a good amp to power these subs with
Answer:	It should because that is the correct size. Check the long side of the iPad (opposite the volume controls) for 3 round connector dots. If you have those it will work. This is the best keyboard I ever used!
Question:	Will these fit facing up towards the hatch in the trunk of my 92 camaro rs
Answer:	Clam Case has a cover for the back of the iPad (iPad inserts into it). It also allows 360* motion so you can sit it up like a backwards L or upside down V.
Question:	What is the height of the box? And can it fit in trunk of 2016 camaro convertible
Answer:	No, the keys are not backlit