13 best watts gas heaters

Product description

Watts Floodsafe Water Detector Shutoff for Gas Water Heaters will protect your home or building from excessive water damage due to water heaters leaks or malfunctions. The FloodSafe Water Detector Shutoff is designed to detect the presence of water beneath the water heater and automatically shut off the cold water supply and power source to the water heater, protecting your investment from catastrophic water damage.

• Shuts off the water supply to your water heater, securing the leak, but further protects by shutting off heater's power
• Audible and visual alarm to alerts owner of water heater leaks
• Can be connected to remote monitored alarm services
• Resettable: not a one-time use device
• For standing pilot gas valve, right-hand thread thermocouple (3/4-Inch size pipe)

User questions & answers

Question:	Is this for a standing pilot gas water heater, or can it be used with an electronic ignition such as a power vented water heater
Answer:	The Watts Floodsafe can be used on gas water heaters that has a standing pilot or Pizo ignitor. Not sure if it will work on gas water heater with electronic ignition with a glow stick ignitor.
Question:	Is this a lead free device
Answer:	I work for a plumbing company and we tested this exact Watts Floodsafe product at the beginning of 2013. At the time, it did not indicate that the brass valve was lead-free compliant. However, as of January 4, 2014, The Reduction of Lead in Drinking Water Act (Federal Public Law 111-380) mandates that any fixture, fitting, etc. sold in the United States that comes into contact with potable water must contain less than 0.25% of lead by weight. Therefore, according to the law, manufacturers, retailers, distributors, etc. cannot sell products that do not meet the new Federal guidelines after January 4th of this year. Many companies that sell these type of products are indicating on the product, packaging, manuals, etc. that the product is lead-free compliant. Watts is a reputable company in the plumbing industry and they advertised that they started converting their inventory over to lead-free compliant products some time ago. However, I recommend checking with the company to make sure that the product is lead-free compliant.
Question:	can this be used to shut off main water supply for the whole house
Answer:	In theory, yes, but you would have to place it at the entrance pipeline that comes into your house. The main issue you have to face is where to place the single water sensor that comes with the unit. An ideal system would have a number of sensors that could be placed under every source of water, such as the dishwasher, clothes washer, etc. It would also be great if that system used wireless sensors and sent an alert via email to your phone. I don't know any reasonably priced system that does those things.

Product description

This Smart Technology electric tankless water heater is configured as a "whole home" model for climates where incoming water temperature is 67°F and above. This model is well suited for heating up to 2-Gallon per minute, which is the equivalent of one shower head (with a 1.5 gpm flow) and one sink with a low inlet water temperature of 67°F and an output setting of 105°F. Digital Temperature Control allows you to set your temperature in increments of 1 Degree. This model can also be used in colder climates as a Point of Use for a sink or other low flow application. All tankless water heaters are sized based on flow rate and temperature rise, and there is a direct relationship between the two. So if used in a cold area requiring a high temperature rise, it will be more limited in the amount of fixtures (gallons per minute) it can heat at one time compared to a warmer climate. When sized properly this water heater will provide endless hot water and only consume the energy needed, giving the user complete control. Prior to purchase and installation please verify this model is the right size for the expected demand and electrical requirements. The ECO 11 requires a minimum 125 amp electrical panel for installation with 60 amp double pole breaker connected to set of #6 awg wire. Plumbing connections are 1/2" compression fitting with the option of 1/2" NPT adapter included. For additional assistance please feel free to contact our support center at 877-474-6473.



NOTE : 11Kw at 220 is equal to 13kw at 240. .Activation Flow : 0.3 GPM

From the Manufacturer

This Smart Technology electric tankless water heater is configured for climates where incoming water temperature is 67 Degree F and above. This model is well suited for heating up to 2-Gallon per minute, which is the equivalent of one shower head (with a 1.5 gpm flow) and one sink with a low inlet water temperature of 67 Degree F. Digital Temperature Control allows you to set your temperature in increments of 1 Degree. This model can also be used in colder climates as a Point of Use for a sink or other low flow application. Prior to purchase and installation please verify this model is the rights size for your hot water needs and electrical requirements.

• Lifetime warranty
• Save up to 60-percent on your water heating cost with an ECOSMART electric tankless water heater
• Never run out of hot water with an ECOSMART tankless water heater
• Patented Self Modulating Technology and design
• ECOSMART tankless water heaters are 99.8-percent energy efficient.Uniform Energy Factor:0.98

User questions & answers

Question:	Ours has only been in service for less than a year - will not adjust temperature to anything above 85 Deg. F. What do you think is the problem ? kds
Answer:	My only guess is that the rheostat (variable resistor) that the temperature adjustment knob is attached to may be faulty. If that isn't it then I don't know. Sorry.
Question:	The warrenty says that this unit must be installed by a licensed electrician and plumber, for them to honor the "life time warrenty." why
Answer:	Hello Bob, The reason is the same as why an innumerable number of gadgets around the world have that little "warranty void if removed" label. Because getting inside of one requires a certain level of training and expertise. Same with this unit. GadgetsGo is an authorized Ecosmart dealer. Kind regards,HenryGadgetsGo
Question:	My house is wired 110V. What additional items do I need to purchase for the conversion
Answer:	Just to expand slightly on prior answers, normally a residential service feed is 240 volts between the two incoming hot legs. There is also a neutral leg, which (hopefully) has zero potential with reference to ground. The voltage between either one of the hot legs and the neutral leg is 120 volts. The 120 volt circuits in your house are connected to one or the other of the two hot legs, and only one. An attempt is made to assign circuits to the two hot legs in a way that will roughly balance the load between them. The other side of a 120 volt circuit is connected to the neutral leg. There is additionally a safety ground run with the circuit, which also ties into the panel. Certain devices require more power (work product of current and voltage) than is practical to deliver using a 120 volt circuit. Common examples are your clothes dryer, and your electric stove. These devices are powered by both hot legs, with a difference in potential of 240 volts. This water heater is also such a device.STRONG BUT FRIENDLY WARNING: If you did not already know this, please don't make wiring this water heater your learning opportunity with electricity. Hire someone who knows how to do it right. Cutting corners, especially with higher currents and voltages, can lead to equipment damage, fire, and electrocution. Electricity is not magic, and you can certainly learn how to do many common wiring tasks safely on your own, but today is not the day to begin that journey. You need properly sized components, properly installed, and connected to an adequate service. Also, if you really, really foul up, you could conceivably wind up making that morning shower more energizing than you ever imagined, if you get what I mean. So newly aspiring electricians should go fix their grandmother's favorite table lamp instead. Once they have that working they can use it to to start reading books about electricity, residential wiring, and eventually, books about this stuff: http://amazon.com/s/ref=nb_sb_ss_c_0_8?url=search-alias%3Dstripbooks&field-keywords=nec+code&sprefix=nec+code%2Caps%2C164 . Of course, you still have to know not to nick conductors when you strip them, and other trade craft like that ; ) . Like almost everything in life that is fun, electricity will hurt you. Sort of like all those people you dated for a while, and then wished later you had never met.
Question:	what amp breaker is required
Answer:	The National Electrical Code requires conductors and overcurrent protection to be sized at 100% of the manufacturer's branch circuit recommendation for tankless electric water heaters. A 60 amp breaker is the same price as a 40 or 50, it is the wire that costs more. #6 AWG wire is required for a 60 amp circuit. If you undersize the wire it could overheat and catch fire. Protect your family and follow the manufacturer's sizing for this, or any other, electrical device. Your family's lives are worth the extra money. 

Product features

3 Smart Steps for Endless Hot Water

Step 1: Determining your average inlet water temperature is important, this allows you to determine how well your unit will perform in your desired location. A lower inlet water temperature will require a higher kilowatt product.

Step 2: Next you will determine how many applications your unit can run simultaneously at your chosen location inlet water temperature. Tankless electric water heaters are sized for maximum simultaneous use, not maximum fixtures in your home.

Step 3: Determining specifications and electrical infrastructure is important because without the correct infrastructure your unit may not fit into your breaker panel.

Product description

This Watts gas water heater supply line kit comes complete with everything you need. It includes two stainless steel supply lines, two brass compression adapters for copper pipe connection, and yellow sealing tape. Ideal for installation of new water heaters, or replacement of existing connectors. For safest results, it is recommended that a new gas supply line be used each time a new water heater is installed.

• Complete kit
• Long-lasting stainless connectors included
• Includes 24-Inch stainless steel gas flex line
• Easy to install
• The wetted surface of our Lead Free products contacted by consumable water contain less than one quarter of one percent (0.25 Percent) of lead by weight

User questions & answers

Question:	Does anyone know the diameter of the water connectors? Are they 3/4" or 1"? Thanks
Answer:	Yes I installed on a 40 galon water heater
Question:	What is the length of the water lines
Answer:	Yes
Question:	so were they 1/2" lines with 3/4" adapters? previous question not answered
Answer:	I am not sure about the number but it was a perfect fit for my 40 gallon Whirlpool hot water heat.

Product description

WATTS WATER TECHNOLOGIES GIDDS-1030401 Potable Water Expansion Tank, Model #Plt-5, Stainless Steel Nipple, 2.1 Gallon, Lead Free

• This product is highly durable
• This product adds a great value
• This product is manufactured in United states

User questions & answers

Question:	Rv parks pressure varies. have my incoming pressure set at 40psi. but when using the pump, it comes on at 35psi, & off at 60psi. is this a fit 4 us
Answer:	May be helpful, but the pump run pressure range of 15psi is probably normal
Question:	What is the connection size
Answer:	The fitting connection is 3/4" NPT threads.
Question:	if this tank comes recharged at 20 psi can I add air too it if needed? the watts I have now is recharged at 40 but is bad now
Answer:	Yes air can be added. There is a valve stem at the bottom of the tank. As I recall, I brought the pressure up to 40 lbs. I checked out their website to see what I use for my well pump switch that runs 40 to 60 lbs.
Question:	This tank will be used on an rv, do any of the tank suppliers offer either a wall mount or cradle type floor mount for the heavier tanks? thanks, ray
Answer:	Hi Ray, I purchased the same expansion tank, and mounted it on my wall. The bracket I used was called Hydro Claw, by storm king. Its not cheap at about $35 to $40, but it is a well made, heavy duty bracket. Very nice looking install. Even my plumber buddies are very impressed! Highly recomend. Good luck, and stay safe. Jeff H.

Product description

This Watts 3/4-Inch Lead Free Brass FPT Temperature and Safety Pressure Relief Valve is a self-closing temperature and pressure safety relief valve used for hot water heaters. It provides temperature relief at 210-Degree F and pressure relief at 150 psi.

From the Manufacturer

This Watts 3/4-Inch Lead Free Brass FPT Temperature and Safety Pressure Relief Valve is a self-closing temperature and pressure safety relief valve used for hot water heaters. It provides temperature relief at 210-Degree F and pressure relief at 150 psi.

• Provides the least expensive and proven means for protection
• 3/4-Inch valve body length, 1-1/8-Inch long shank
• Self-closing safety valve for hot water heaters
• 3/4-Inch MPT male pipe thread inlet and female outlet
• 150 psi maximum

User questions & answers

Question:	Will this fit a 40gal Bradford White
Answer:	Your best bet is to get the number off the tag and see if you can match that up on the Watts website. There are many, many types and brands of water heater and multiple models within brands. You'll be more likely to get the exact right one with the original part number.
Question:	I can't fine the 3/4 LF100XL-DP-150 part on Watt's site, is this a typo and it should be 3/4 LF100XL-4 M7 (Watts ordering code
Answer:	look up LF100XL-DP-TT-150 The main difference between this one and part number 0550600, is that it has a 4" probe where this has a 3" probe.
Question:	Watts tech support told me I need order code # 0556000 - is that the same as 0958208 which is on the back of this item
Answer:	The two part numbers are not the same. The spec is slightly different. From what I see, they told you to get the one with a 4" probe, while this one has a 3" probe. That could make a difference if your water heater has thick insulation. Otherwise the specs are pretty similar. This is the one they told you. https://www.watts.com/products/plumbing-flow-control-solutions/relief-valves/temperature-and-pressure-relief-valves/lf100xl/lf100xl-150210 This is the one from Amazon your are asking about. https://www.watts.com/products/plumbing-flow-control-solutions/relief-valves/temperature-and-pressure-relief-valves/lf100xl/dp-tt-34 Amazon does not appear to have the model number they told you, however, they do have some different brands with otherwise the same, with a 4" probe. I would suggest comparing the specs of other substitute models with those listed for what they told you. Just make absolutely certain, the temp and pressure specs match. These are a safety device that keeps your water heater from blowing up! If the one you have now seems OK but is leaking very slightly, you can sometimes clean them up. Take it out, flip the lever so it is open, then soak it in some vinegar for an hour or two, then flush it out. Usually, some deposits get caught in the valve seat so it doesn't close tightly. If it's not to scaled up, they will often clean up and seal again. If it's relieving on you frequently, you may have some other problem with the water heater. GOOD LUCK!
Question:	My current valve is 100xl-4 m7. is this the same valve
Answer:	yes it is.

Product description

The Watts Hot Water Recirculating Pump provides hot water at every faucet or shower when needed, eliminating wasted water and saving up to 15,000 gallons per year. It is easy to install on any water system and requires no additional piping. The unique design of the pump ensures quiet, maintenance-free operation. The system includes a built-in 24 hour, a dual setting programmable timer to activate the pump only when needed. Please note this will not work with a tankless water heater.

From the Manufacturer

The Watts Premier hot water recirculation pump puts hot water at every tap when you want it. Saves up to 15,000 gallons per year. The pump brings convenience and savings to your home, giving you hot water instantly at every faucet, when you need it. This unique product is easy to install and not only provides you with the convenience of hot water when you need it, but saves an average of over 11,000 gallons per year. *May not work with a tankless water heater.

• Kit includes a pump with timer with 10' cord, 2 adapters with rubber washers, valve mounting screws, sensor valve, and two 12-inch supply lines
• Voltage: 120 volts, Item Weight: 8.5 pounds. Overall Dimension: 6.2 x 6 x 5 inches
• Provides hot water at every faucet or shower when needed and helps eliminate wasted water
• Easily installs to existing plumbing and is maintenance-free
• 24-hour programmable timer activates pump when you need it

User questions & answers

Question:	How many amps is the pump
Answer:	The pump runs at .22 Amps, and recommended supply current of 2.5 Amps. A standard 15 Amp wall socket is all that you need to plug it into. The .22 Amps the pump indicates maximum start up current, actual running current will be somewhat lower. Inrush current is always higher, when the motor has to start up, actual running current will be lower, example a 1 HP motor will have an inrush current of about 34 Amps, just until the motor reaching normal operating speed then it drops down to around 7.5 Amps, quite a bit lower, but the breaker needs to be able to handle the inrush currents.
Question:	can i used without the sensor valve
Answer:	Yes.As long as you have a return line running back to your water heater. You do not need a separate return line at every faucet. You need one return line. Follow your hot water pipe to the end (last branch takeoff), cut in a tee and run pex or copper. At the bottom of your tank style water heater there is a small, usually plastic valve. Remove that valve and screw in a 3/4" brass or stainless pipe nipple. Then install a tee inline with side outlet looking up and in the end of the tee put a brass drain valve to replace the crappy plastic one if applicable. The side connection on the tee you installed is where you will connect your return line you just ran. I did not notice if this pump had a built in check valve but if not you may want one to prevent water from flowing through both the hot water main and the hot water return to the faucet nearest the end. Water will follow the path of least resistance so the last branch on the main usually ends up being similar in distance to the water heater from either line. As a result water can back feed up the return line and will bring the cold water entering the tank with it. This is especially true when a second source of hot water is being used at the same time hence the need for a check valve.
Question:	If the pump is on, and the water is hot, the sensor valve closes, right? Isn't the pump trying to push water against a totally closed line
Answer:	This type of pump is designed to operate with zero flow, and it actually uses a little less electricity when it is not moving water. When the sensor valve closes, the pump does not move any water. When the sensor valve reopens, the pump moves water from the hot water line into the cold water line.
Question:	So what this does is move the hot water through the pipes constantly, not just when you need it? Seems like an energy suck. Is it
Answer:	If you run this all the time you will likely increase your water heating costs significantly as you are turning your pipes into a big radiant heater. You can use the built in timer to only have it come on at set periods, but this will only work if you have a very fixed schedule. I attacked this another way. I plugged the unit into a TP-Link HS110 Smart plug that is Alexa controlled. I can just say turn on hot water pump or turn off hot water pump when I want to control it. But that was not good enough for me. I found that if this pump ran for four minutes it would give me hot water at the distant shower that I wanted, so I did the following. I wrote a routine to turn on the pump, wait four minutes and then turn it off. While I can run this by voice, I bought the new Amazon Alexa Button, they are about $14 for a two pack. The button is battery operated and communicates to another Alexa device. Just before I take a shower I push the button and within four minutes the water will be hot without having to run water.

Product features

Includes Everything Needed

Pump with timer and 10 ft. electric cord, two adapters with rubber washers, valve mounting screws, sensor valve, two 12 in. supply lines

Easy Installation

Easy to install, usually less than one hour.

Save Money

Save money, up to 10% of your water bill annually.

Product description

This lead free tankless service valve kit is designed to simplify the installation, maintenance and operation of tankless water heaters. This 3/4 inch tankless hot and cold water heater valve set with female thread connection and no spring check facilitates isolation of the water heater from the water lines, water heating purging and draining. It replaces up to 18 fittings and 16 connections used in typical tankless water heater installations. It features a lead free copper silicon alloy body, full-port quarter-turn ball valve with color-coded T-handle, virgin PTFE seats, purge and drain valve with a hose connection and tethered brass cap, FPT union connection to water heater and FPT connection to waterline. The pressure rating is 600 psi (41. 4 bar) WOG. Features: Replaces up to 18 fittings and 16 connections used in typical tankless water heater installation Optional pressure relief and check valve Simplifies the installation, maintenance, and operation of tankless water heaters Hot and cold valves certified to NSF/ANSI 61From the Manufacturer: Designed to simplify the installation and maintenance of tankless water heaters, the Watts Series THW Tankless water heater valves replace up to 18 fittings and 16 connectors used in typical tankless water heater installations. Available in two valve sets for both hot and cold water with 3/4-inch female threaded union brass fittings.

From the Manufacturer

This Watts Series THW Tankless water heater valves are designed to simplify the installation and maintenance of tankless water heaters They replace up to 18 fittings and 16 connectors used in typical tankless water heater installations Available in two valve sets for both hot and cold water with 3/4-inch female threaded union brass fittings

• TANKLESS WATER HEATER VALVE KIT: Watts LFTWH-FT-HCN service valve kit for tankless water heater valves simplify the installation, maintenance and operation of tankless water heaters.
• SERVICE VALVE KIT FOR TANKLESS WATER HEATER: The tankless water heater service valve kit replaces up to 18 fittings and 16 connections used in typical tankless water heater installations, color-coded tee handle. Optional pressure relief and check valve.
• MULTIPLE CONNECTION VALVE KIT: They are available in two valve sets or as a single valve with female threaded, union or quick-connect end options. The service valve kits are available with or without a relief valve. Facilitate service and maintenance with cold water inlet and hot water outlet valves certified to NSF/ANSI 61.
• LEAD FREE VALVE KIT: The wetted surface of our Lead Free products contacted by consumable water contain less than one quarter of one percent (0.25 percent) of lead by weight.
• WATER SERVICE VALVE KIT: Purge/drain ports allow regular cleaning to remove scale build-up. The kit includes LF4L - Lead free poppet type pressure relief valves for protection against excessive pressure and LFTWH - Lead Free Tankless Water Heater Valves.

User questions & answers

Question:	What type of fittings are on the inlet and outlet side of the unit
Answer:	standard 3/4 pipe your choose of copper,pvc,. etc
Question:	Is the drain valve threaded outlet 3/4 or 1/2 inch
Answer:	if it says it is a 3/4" Service Valve Kit - all fittings are 3/4"...
Question:	how do i stop it from leaking at union
Answer:	Have you tried plumbers tape? Sometimes you have to wrap the plumbers tape around the threading several times to get a good seal.
Question:	Inline filter for a Tempra tankless water heater
Answer:	Not sure you need a inline filter, you can get a kit to flush your tankless once a year , with vingar or they sell cleaner made for them. It's two shut off valves on the in and out of unit , also nice to have if you need to have work done on unit .

Product features

Service Valve Kit

Replaces up to 18 fittings and 16 connections used in typical tankless water heater installations, color-coded tee handle.

3/4" Valve Set

This 3/4 inch tankless hot and cold water heater valve set with female thread connection and no spring check facilitates isolation of the water heater from the water lines, water heating purging and draining.

Pressure Rating

The pressure rating is 600 psi.

Product description

High BTU gas connector for use with boilers, commercial water heaters, gas meters, gas packs/rooftop HVAC units, furnaces, and tankless water heaters

From the Manufacturer

This Dormont gas connector is CSA Design Certified domestically and internationally for indoor and outdoor use with natural, manufactured, mixed, liquefied petroleum, and LP-gas air mixtures Durable, naturally corrosion-resistant 304 stainless steel construction offers an exclusive no-neck design to increase flexibility Quality flared end fittings create a metal to metal seal to ensure integrity in critical applications Manufactured domestically in the USA, all Dormont gas connectors are 100 percent leak tested to ensure consistent quality you can trust.

• Designed for: High BTU applications such as; Commercial hot water heaters, Outdoor back-up generators, Tankless water heaters, Commercial Furnace or Bolier
• Included Adapters - 90-4041- - 3/4 In.ID Flare X 3/4 In. MIP (Tapped 1/2 In. FIP) - 90-4042- - 3/4 In.ID Flare X 3/4 In. FIP
• 290,900 BTU
• 100% Factory leak tested
• 304 Stainless Steel flexible tubing with plated steel end fittings
• Indoor or Outdoor Use
• CSA Approved
• BAA Compliant

User questions & answers

Question:	Have 199,000btu tankless wtr heater 3/4" tapered male & 3/4" female valve supply line will this work? Or any suggestions
Answer:	I have it supplying a 400.000 btu pool heater. It has flare adapters and pipe threads. Should work. By tapered I think you mean flare.
Question:	Gas pressure rating
Answer:	I used on propane 12lb pressure its higher then natural gas the flex are full flow 3/4" very durable higher quality price is good. Thank you
Question:	Is this is just a steel or brass coragated hoses with a coating on it? Or a stainless steel polyethelene coated hose flexible like a garden hose
Answer:	It is a braided stainless steel/ hose covered with a plastic exterior.
Question:	are the ends supposed to swivel? the pvc coating keeps the flare nuts from turning
Answer:	sorry one end swivel

Product features

Dormont: A Gas Safety Company

Your most basic home needs, such as gas heat, kitchen range, dryer, hot water, and standby generator power, rely on a tested, durable connection system—and the safety of your home and family depends on the quality of the connectors you choose. At Dormont, we make every connector as if we were going to install it in our own homes.

As a leading inventor and manufacturer of safe, high-quality stainless steel gas connectors, Dormont has earned the reputation as one of the foremost experts in safe gas connectivity for the home. We have been the industry-leading manufacturer of the broadest line of high-quality, safe, and long-lasting stainless steel gas connectors for decades, and will continue to be an innovative, reliable source for residential gas solutions for decades to come.

Dryer and Water Heaters

Tubing is durable, flexible, and corrosion-resistant.

Home Appliances

• Ranges
• Stoves
• Furnaces
• Boilers

Commercial Applications

• Commercial Hot Water Heaters
• Commercial Furnaces
• Commercial Boilers
• Rooftop Units
• Standby Generators

Gas Hearth

Approved for indoor and outdoor use with stationary gas appliances.

Product description

Watts LFTWH-UT-HC-RV Tankless Water Heater Valve Set with Relief Valve is designed to simplify the installation, maintenance, and operation of tankless water heaters. This economical valve set provides all necessary valves and fittings required for typical tankless water heater installations and facilitates easier water heating, purging, and draining. It includes a hot and cold valve set with spring check valve, a pressure relief valve set at 150 psi, full port quarter turn ball valve, 3/4 in. union connection to the water heater, and 3/4 in. union with threaded tailpieces for connection to the plumbing line. Lead Free* construction to comply with Lead Free* installation requirements. The pressure rating is 600 psi.

• Simplifies installation and operation of gas or electric tankless water heaters
• Lead Free* copper silicon alloy body
• Color-coded ball valves
• Quarter-turn purge and drain valve
• Easy to install

Product description

This Watts stainless steel corrugated water heater connector is used to connect electric or gas water heaters to supply. The corrugated design offers the highest flexibility and flow available providing a kink-free connection. These connectors also provide a built-in dielectric sleeve to eliminate the need for a separate dielectric union. Built-in stainless iron.pipe threaded swivel adapters allow a sweat-free installation.

From the Manufacturer

This Watts stainless steel corrugated water heater connector is used to connect electric or gas water heaters to supply. The corrugated design offers the highest flexibility and flow available providing a kink-free connection. These connectors also provide a built-in dielectric sleeve to eliminate the need for a separate dielectric union. Built-in stainless iron.pipe threaded swivel adapters allow a sweat-free installation.

• Corrugated stainless steel water heater connector 12-Inch length and 3/4-Inch FIP by FIP
• Built-in threaded swivel adapters
• Highly flexible corrugated stainless steel
• Max pressure 125psi

User questions & answers

Question:	Do you need a dielectric union when connecting these to a copper supply line
Answer:	if i can help anyone i will
Question:	What is the Temperature rating for these Watts connectors
Answer:	yes
Question:	Is the interior wall plastic or steel
Answer:	yes
Question:	It looks like these have smaller inside diameter than an equivalent straight 3/4" copper pipe. Can someone verify this
Answer:	Not sure Sorry

Product description

This Dormont gas connector is CSA design certified domestically and internationally for indoor and outdoor use with natural, manufactured, mixed, liquefied petroleum, and lp-gas air mixtures durable, naturally corrosion-resistant 304 stainless steel construction offers an exclusive no-neck design to increase flexibility quality flared end fittings create a metal to metal seal to ensure integrity in critical applications manufactured domestically in the USA, all Dormont gas connectors are 100 percent leak tested to ensure consistent quality you can trust.

From the Manufacturer

This Dormont gas connector is CSA Design Certified domestically and internationally for indoor and outdoor use with natural, manufactured, mixed, liquefied petroleum, and LP-gas air mixtures Durable, naturally corrosion-resistant 304 stainless steel construction offers an exclusive no-neck design to increase flexibility Quality flared end fittings create a metal to metal seal to ensure integrity in critical applications Manufactured domestically in the USA, all Dormont gas connectors are 100 percent leak tested to ensure consistent quality you can trust.

• Designed for: Clothes Dryers and Water Heaters
• Included Adapters - 90-2031- - 1/2 In.OD Flare X 1/2 In. MIP (Tapped 3/8 In. FIP) - 90-2032- - 1/2 In.OD Flare X 1/2 In. FIP
• 71,100 BTU
• 100% Factory leak tested
• 304 Stainless Steel flexible tubing with plated steel end fittings
• Indoor or Outdoor Use
• CSA Approved
• BAA Compliant

User questions & answers

Question:	Does this hose behave like a piece of rope and return to straight after bending or will it hold its new shape after it has been bent,like a flex hose
Answer:	I recommend checking on searsparts.com.
Question:	Is a flexible rubber hose safe to use with propane
Answer:	Yes, it works.
Question:	Can I use the yellow hose to hook up my gas fireplace logs , as long as it not on or above flames
Answer:	Yes, these are the same parts.
Question:	I already have one 3 foot hose and need more hose to be able to move the stove. Can I just screw this on to the existing hose
Answer:	yes that is the model i bought it for in fact ... it will

Product features

Dormont: A Gas Safety Company

Your most basic home needs, such as gas heat, kitchen range, dryer, hot water, and standby generator power, rely on a tested, durable connection system—and the safety of your home and family depends on the quality of the connectors you choose. At Dormont, we make every connector as if we were going to install it in our own homes.

As a leading inventor and manufacturer of safe, high-quality stainless steel gas connectors, Dormont has earned the reputation as one of the foremost experts in safe gas connectivity for the home. We have been the industry-leading manufacturer of the broadest line of high-quality, safe, and long-lasting stainless steel gas connectors for decades, and will continue to be an innovative, reliable source for residential gas solutions for decades to come.

Dryer and Water Heaters

Tubing is durable, flexible, and corrosion-resistant.

Home Appliances

• Ranges
• Stoves
• Furnaces
• Boilers

Commercial Applications

• Commercial Hot Water Heaters
• Commercial Furnaces
• Commercial Boilers
• Rooftop Units
• Standby Generators

Gas Hearth

Approved for indoor and outdoor use with stationary gas appliances.

Product description

Used in water heater and hot water storage tank applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters up to 105,000 BTU/hr. Features a bronze body with NPT male inlet and NPT female outlet connections, unique thermostat with special thermo-bonded coating, and a test lever. ASME rated and CSA listed. Temperature Relief: 210 degrees F (99 degrees C), Pressure Relief Range: 75 to 150psi (5.2 to 10.3 bar).

• Features a unique thermostat with special thermo-bonded coating
• Thermostat is accurate and proven

User questions & answers

Question:	What is the diameter of the threaded area
Answer:	This valve has a 3/4" NPT thread. A 3/4" NPT pipe thread has an outside diameter of 1.050 inches. Hope this information helps.
Question:	What is the length of the temperature probe
Answer:	Sorry, I did not measure the length of the probe. The new valve was the exact same make and model of the leaking valve I replaced. My water heater is a 50 gallon unit, the length of the probe would not have been an issue. The valve was a bargain compared to other sources.
Question:	My oem watts 100xl says it's a 8 inch probe...... haven't removed it yet to verify, but is this that long
Answer:	It is an exact 100xl oem replacement. Open with confidence. Great product.
Question:	Will this replace a t&p valve for a state industries model # es655dortgw water heater
Answer:	The T&P valves for home water heaters are standard in most ways. They have 3/4" threads for the inlet and outlet and 150 psi pressure relief setting. The only difference is the length of the stem. The stem is the portion of the valve with the male (external) threads. Some have almost no distance from the threads to the body of the valve and some have up to a couple of inches. Look at the one on you unit and buy one with a similar stem length. A little too long is OK. Too shot can be a problem.