13 best thermostat for heat lamp

Product description

Infrared Ceramic Reptile Heat Bulb:

Specifications:

Socket: E26;

Volt: AC 110-120V;

Watts: 150W;

Material: ceramic, NiCrAl;

Diameter of heating surface: 85mm;

Note: 1. Lamp surface temperature is too high, do not directly touch during it works; 2. Before remove it from fixture, please allow at least 1 hour for cool to avoid scald ; 3. Accidents may happen due to improper operation so please use it in a right way and avoid using in damp environment; 4. Please adjust the distance between the lamp and the pets, at least 35cm; 5. Please away from combustible or explosive materials；

Clamp Light:

Specification：

Volt: 120V;

Watt: Accepts up to 150W bulb (E26);

Reflector Diameter: 8.5 inch;

Cord: 6 feet;

18/2 SPT-2 cord clamp light can also be used as a table lamp in your room, garages or art studios, a work light in photography and workshops, amphibians and reptiles pets terrarium heat lamp, and even a growth light for indoor plants.

Warning: The power cord on this product contains chemicals, including lead known to the State of California to cause cancer. Wash hands after use.

Digital Thermostat Controller:

Specifications:

Temperature control range: 40℉-108°F;

Temperature display range: 32℉-140°F;

Rated Voltage: AC 120V 60Hz ;

Max Loading: 8A 1000W ;

Easy plug-in operation with LED illuminated indicator lights & three-prong ground plug. Digital thermostat can also be used to control the temperature of many other appliances as long as they don't exceed the maximum electrical specifications stated above. Simply place the sensors in the area where the temperature needs to be controlled plug the appliance into thermostat, and set the desired temperature.

Abnormal Warning: 1. If thermostat shows "E1", it means that the actual temperature is lower than 0℃ or 32℉; 2. If thermostat shows "E2", it means that the actual temperature is higher than 60℃ or 108℉. 3. If thermostat shows "E3", it means that the temperature sensor is not working properly. Please re-install the sensor；

• Multifunction: great for reptile and amphibian terrariums, incubating poultry heater, can increases blood circulation promoting health and healing.
• Perfect 24h heat source: heat bulb does not emit any visually detectable light, would not disturb pets sleep. 150W, E26 lamp base. Material: ceramic, NiCrAl. To avoid scald, please wait at least 1 hour to cool down after turning off the bulb.
• Multifunctional clamp light: scratch-resistant sleeves covered clamp would not leave marks on your surfaces, 360° adjustment and 8.5inch aluminum reflector can focus light where you need. Volt: 120V, Watt: 150W (E26). have convenient on/off button.
• Temperature range: digital thermostat provides temperature control between 40-108℉, temperature display range: 32-140°F. Support Celsius or Fahrenheit readout. Volt: 120V 60Hz; Max Loading: 8A 1000W. Do not immerse controller or probe into water.
• Package include: 1-pack 150W ceramic heat bulb, 1-pack digital thermostat (easy plug-in operation with LED illuminated indicator lights and three-prong grounded plug), 1-pack clamp light with 8.5 inch reflector.

User questions & answers

Question:	Where should the probe go if I'm using it for a hedgehog setup
Answer:	I just lay mine (I have two; one on each, diagonal end of the cage) on the top of the cage. Then I don't have to worry about my hedgie chewing on the electrical cords. I have thought about placing them under the canvas (the bottom) of the enclosure also. I know that my current readings are slightly warmer than the actual temp where the hegie is due to the fact that the probes are about 7-10 inches above him. These lamps/thermostats work so well. I'm very happy with them. (Note: The digital temp tends to run about 2 degrees cooler than the thermostat setting)
Question:	does it light up or just heat
Answer:	These bulbs are heat only.
Question:	Does the temp control actually adjust the temperature on the ceramic element
Answer:	No. The temp control is like a thermostat and adjusts the environment temp. The ceramic element is either off or on.
Question:	Can 1 thermostat be connected to 2 lamps
Answer:	Thermostats like this have a one time fuse to prevent overload. The thermostat will have a Max amp rating. For instance, I ran two heat mats on this just fine with a splitter but when I added my space heater it exceeded the max amo rating and broke the one time fuse. This fuse is not replaceable.

Product features

Specifications

• Socket: E26
• Voltage: AC 110-120V
• Watts: 150W
• Material: Ceramic, NiCrAl
• Color: Black
• Diameter of heating surface: 85 mm
• Height: 100 mm
• Package Includes: 1-pack 150W ceramic heat bulb

About Clamp Light

1. Supply powerful light anywhere you require it with this 8.5" Clamp Light.
2. It is constructed with a scratch-resistant vinyl sleeve and a spring-powered steel clamp with an adjustable ball joint, which allows you to easily position the lamp almost anywhere.
3. The lamp includes an easy to use, energy efficient on/off switch that saves energy.

• Volt: 120V
• Watt: up to 150W
• Reflector Diameter: 8.5 inch
• Lamp Type: type A lamp (E26)
• Cord: 6 Feet
• Material: Aluminum

Easy to Use

• Fahrenheit Light: It will be lighting when the temperature display in Fahrenheit.
• Celsius Light: It will be lighting when the temperature display in Celsius.
• Heating Light: It will be lighting when the output is working.

NOTE: Please note that the controller can only be used to power off heating equipment at setting temperature and does not increase the heating power of the heating equipment

• ✓ EFFORTLESS HEATING SETUP: Simply set the temperature probe, plug-in the controller, and use the large 3-button interface to choose your desired temperature setting. Digital display supports units in both Fahrenheit and Celsius. Note: the controller is designed to have a 2-3 degree buffering zone before powering on again after reaching set temperature.
• ✓ EASE OF MIND: Handy LED heating and power indicator lights allow you to see the controller’s status even in total darkness. Controller features a convenient hanging tab, and a bright, easy-to-read display inside a tough plastic housing.
• ✓ RUGGED CONSTRUCTION: The cord for the temperature probe and grounded 3-prong plug measure an extended 6 feet in length, designed to suit almost any application you can imagine.
• ✓ VARIETY OF USES: Our thermostat controller can be used for seedling germination, rooting, brewing, heating, fermentation, and more, keeping your various environments in their ideal temperature range.
• ✓ SAFE & RELIABLE: Our thermostat controller is ETL listed, and rigorously tested for quality control and safety. Conforms to UL Std No. 60730-1, 60730-2-9. Temperature control range is 40-108°F, temperature display range is 32 -140°F. Rated Voltage is 120VAC 60Hz, Max Loading: 8.3A 1000W. Do not immerse controller or probe into water.

User questions & answers

Question:	Is there an instructional video on how to put the temperature controller and heating pad together? Or an instructions pamphlet
Answer:	Hello, you can plug the heating pad to this controller and set the desire temperature, place the sensor to where you want the temperature to be controlled(for example, into the soil) then it should start working. You can find the manual of this controller here: https://centurytimer.com/product_resources/BNQ-T7BH/Instruction-Manuals-for-Web-BNQ-T7BH.pdf
Question:	Can a heat lamp be plugged into it and control the heat like if it was a mat
Answer:	Is this accurate with a heat lamp?
Question:	Is it normal for this to make an audible clicking noise when it turns on? Just got mine set up and it clicks when it turns on
Answer:	Is there anyway to disable that clicking sound? I just got mine today and its right next to my bed so its really irritating clicking on and off every 5 minutes.
Question:	can this be used for 2 che lamps
Answer:	With the wattage and amperage it says it can supply it should easily be able to handle 2 lamps. Just run a strip off the plug and only have them 2 lamps controlled by the thermostat. AGAIN, as long as it will handle what they say it can handle. A 100watt bulb should only pull just under 1 amp.

Product features

BN-LINK Digital Heat Mat Thermostat Controller

BN-LINK Digital Thermostat Controller is your perfect solution to providing constant optimum temperature for a variety of uses. Our thermostat controller has an easy plug-in operation with LED Illuminated Indicator Lights & Three-Prong Ground Plug.

Effortless Set-Up

A manual is included with our thermostat controller. But with the simple interface, it won't be needed! Please follow these instructions:

1. Plug in the thermostat controller
2. Press and hold the "Set" button to enter the temperature setting
3. Press the UP/DOWN button to adjust the target temperature
4. Press the "Set" button again to complete the process

**Please note that there is a 2-3 degree buffering zone for the thermostat controller to turn your appliance on again**

Switch Between Temperature Units

To toggle between Fahrenheit or Celcius:

• Press and hold the DOWN button for 3 seconds for Celcius
• Press and hold the UP button for 3 seconds for Fahrenheit

Simply Plug Your Appliance In

Our BN-LINK heating thermostat controller has a simple design for the convenience of our customers. Plug in your appliance and watch our thermostat controller maintain the optimal temperature you've set for your needs.

Keep Your Pets Warm

Maintain perfect temperature control in reptile terrariums and small pet enclosures. Place the temperature probe where the heat source will target and watch your pets stay warm and happy.

Great for Seedling and Plant Germination Projects

Grow with BN-LINK. Our thermostat controller is ideal for maintain rooting temperatures in a tray and dome.

Variety of Uses

Help give your aquatic life a comfortable environment with the help of our thermostat controller.

Easy to Mount

With the mounting holes on the back of the thermostat controller, it allows you to customize your area. Mount anywhere you need the thermostat controller to be.

• 🥇🥇【Convenient Design】Plug and play, easy to use. Support °C/°F display.
• 🥇🥇【Dual Relay Output】Be able to connect with refrigeration and heating equipment at the same time.
• 🥇🥇【Dual Display Window】Be able to display measured temperature and set temperature at the same time.
• 🥇🥇【Buzzer Alarm】High and low temperature alarms are available when the temperature is over or the sensor is with issue.
• 🥇🥇【Safety】Maximum output load: 1100W(110V). It is with temperature calibration and compressor delay which can protect your refrigeration.

User questions & answers

Question:	Can I make my deep freeze into a fridge if I plug this into it
Answer:	As far as I know this is only for reptiles, but I’m no expert on mammals. I’d recommend finding one made specifically for young mammals.
Question:	Can I plug another heat belt into the cold outlet? I have one setup right now, would rather not buy another temp controller
Answer:	100% natural phosphorus free oyster shell calcium carbonate
Question:	Have a glass door cooler want to keep temp at 55 willthe probe wire conform to the door
Answer:	The whole is pretty small
Question:	Is the probe waterproof and usable to control homebrew strike water temp
Answer:	No it can’t be hung as it is. If you add some Velcro or some other adhesive yourself it could easily be hung. But as is no.

Product features

Dual Display

• Temperature Control Range：-50~120 °C / -58~248 ° F
• Temperature Resolution：0.1 ° C / 0.1° F
• Temperature Accuracy：±1°C (-50 ~ 70°C) / ±2°F (-58 ~ 160° F)

Heat or Cool Socket

• Temperature Control Mode：On/Off Control, Heating and Cooling
• Input Power：100 ~240VAC, 50Hz/60Hz
• Temperature Control Output：Max. 10A, 100V ~240V AC
• Relay Contact Capacity：Heating (10A, 100-240VAC)/Cooling (10A, 100-240VAC)

Plug & Play

• Buzzer Alarm：High and Low Temperature Alarm
• Ambient Temperature：-30~ 75 ° C / -22~ 167 ° F
• Dimension (Main Body)：140x68x33mm (5.5x2.7x1.3 inch)

Temp Probe

• Sensor Type：NTC sensor (Including)
• Sensor Length：2m / 6.56ft
• Input Power Cable Length：1.5m ( 5ft )

Application

• 👏👏【Convenient Design】Plug and play, easy to use. Support reading with Centigrade or Fahrenheit.
• 👏👏【Dual Display Window】Be able to display measured temperature and set temperature at the same time.Temperature calibration, over-temperature and sensor fault alarm. Maximum output load: 1200W (110V).
• 👏👏【Dual Time Cycle Setting】Can be set different temperature from day and night on the basis of the physical needs of animals and plants during 24 hours.
• 👏👏【Only Heating】Temperature Control Mode: On/Off Control. Please note it is only heating controller without cooling function. Both of the plugs can control the heating. But totally could not over 1200W.
• 👏👏【Sensor Length 】2m / 6.56ft

User questions & answers

Question:	Does this only do heat? Is there a model that is soley for cooling
Answer:	Yes. It is only do heat and the time. We have one for cooling. It is ITC-308.http://www.amazon.com/Inkbird-Itc-308-Temperature-Controller-Thermostat/dp/B011296704/ref=pd_sim_sbs_328_1?ie=UTF8&refRID=00PW2766SPNECBNVYWR0&dpID=417y0W4HFmL&dpSrc=sims&preST=_AC_UL160_SR160%2C160_
Question:	Does this product measure the humidity as well as the temperature
Answer:	Sorry, this ITC-306T cannot measure the humidity. However, we have a combination product that can control temperature and humidity. Pls see the link (https://www.amazon.com/dp/B01N56KEU6). Thanks!
Question:	Do I have to reset it every 24 hours? Or onceset is it good to go
Answer:	Once set, it stays set, even after power outages (of which I've had several since getting mine.)
Question:	Basically I am trying to keep the temperature between 80 and 85 degrees, this includes a heater and fan. How do I set this
Answer:	I initially found the flyer a little difficult to understand, but basically you have to set 2 variables, the target temperature and the temperature differential. So you would set the target temperature to 85 and the differential to 5 degrees. Thus if current tmp >= target - differential it shuts off. If current_tmp

Product features

Specification

• Temperature Control Range：-50~99 ℃，-58 ~ 210 °F
• Temperature Resolution：0.1°F
• Temperature Accuracy：± 2 °F (-58 ~ 160 °F)
• Temperature Control Mode：On/Off Control, Heating
• Input Power：100 ~ 240VAC, 50Hz/60Hz
• Temperature Control Output：Max. 10A, 100V ~240V AC

Packing list

• ITC-306T Temperature Controller*1
• Instructions*1

Product description

1. How Pymeter control temperature?

Temperature controller is actual Heating/Cooling controller, thus MUST SET ON-Temp to turn ON Heating/Cooling, and MUST SET OFF-Temp to turn OFF Heating/Cooling.

Heating starts at LOW Temp [ON-Temp(1oN, 2oN)], stops at HIGH Temp [OFF-Temp(1oF, 2oF)], thus for heating MUST SET 1oN(2oN) LESS than 1oF(2oF);

In heating mode, 1oN(2oN) is the minimum temp you allow, 1oF(2oF) is the maximum temp you allow.

Cooling starts at HIGH Temp [ON-Temp(1oN, 2oN)], stops at LOW Temp [OFF-Temp(1oF, 2oF)], thus for cooling MUST SET 1oN(2oN) GREATER than 1oF(2oF).

In cooling mode, 1oN(2oN) is the maximum temp you allow, 1oF(2oF) is the minimum temp you allow.

2. Reading temp is inaccurate?

Every Pymeter controller is calibrated before come out of factory, it is reading temp accurately!

Please don't compare it to common inaccurate thermostat、thermometer or temp gun. If you doubt Pymeter controller accuracy, please calibrate with ice-water mixture (it is 32F when ice is melting), and you will see which device is accurate then.

3. Beeper keeps sounding?

Probably it is the Alarm settings ( AL、AH、d7 ) you set are NOT the right temperature you want. AL is low temperature alarm(it sounds when current temp is AL or Lower), AH is high temperature alarm(it sounds when current temp is AH or Higher), d7 is difference alarm(it sounds when the temp deviation between sensor 1 and sensor 2 is over d7). If you don't need alarm function, please don't change the values of AL、AH、d7, the default values usually won't trigger alarm. You can factory reset by switching temp unit from F to C in setting.

Please download User Manual PDF in Product information.

• ✓【Dual Probes】Quite different from other thermostats, Pymeter temperature controller is equipped with 2 waterproof accurate sensors, make it possible to control 2 sockets for heater and cooler at the same time or separately.
• ✓【Dual Sockets】Each outlet has independent temperature controlled switch and it intelligently identify heating or cooling mode via ON & OFF set-point, it is very easy and flexible to keep target at desired temperature range.
• ✓【Safe and Reliable】Support High and Low Temperature Alarm; Temperature Difference Alarm, this is very helpful to keep target safe from malfunction of any one probe. Cooking fishes NEVER happen!
• ✓【Enhanced Functions】Power-Off Memory; Power-On Delay; Temperature Calibration.
• ✓【Widely Used】Pre-wired, just plug in and play, suitable for various applications: kimchi refrigerator, garage freezer, carboy heater, home brew kit, chicken coop water heater, water chiller, swamp cooler, seedling heat mat, reptile heating pad, heat lamp, oven thermostat, beer brewing kit, fermenter fermentation bucket, heat mat for plants, grow tent heater etc.

User questions & answers

Question:	The max temp is 210 Fahrenheit correct
Answer:	Yes, correct.
Question:	How do I change the probes from cool to heating in settings? What buttons do I press in what order
Answer:	Cooling and heating are relevant to the "turn on at 'x' temp" and "turn off at 'x' temp" if it is not working in your preference currently, try switching some measurements in opposites of each other.
Question:	How do we get a "Free New Replacement" as mentioned below
Answer:	Please contact support on www-pymeter .com or send message to us on Amazon directly.
Question:	Can you send me a copy of the instructions? Mine didn’t come with any
Answer:	Sorry for that. Please read/download the instruction via this link: https://www.pymeter.com/PY-20TT-User-Manual.pdf, any further question, just message us on Amazon directly :)

Product features

Pymeter Heating and Cooling Temperature Controller

Pymeter Digital Temperature Controller is easy to use, safe & reliable dual outlets thermostat. It is used as over temperature protection or automatic temperature control system with various electric appliances such as heaters for Reptile, Aquarium, Greenhouse, Home Brew, Fermentation, Accelerating Germination, Plant Grow Tent, Pet Breeding, Incubation, BBQ, Terrestrial Heat Control, Aquarium Cooling Fan, Electric Radiator, Electric Oven, etc.

Advantage compare to other Thermostat:

Parameters

Temperature Range: -50~99°C/ -58~210°F; Temperature Resolution: 0.1°C/ 0.1°F

Controller Dimension: 8.26x2.16x1.57 inch; Temperature Accuracy: ±1°C/ ±1°F

Input: 85~250VAC, 50/60Hz; Output: 85~250VAC, MAX 10A

Buzzer Alarm: High/Low Temperature, Differential Temperature, Sensor Fault

Input Power Cord: 4.5ft; Sensor Cable: Waterproof Sensor x2; 2m/ 6.56ft.

Widely Applied

Product description

iPower heating pad thermostat can provide constant customized seed germination, crawling and brewing temperature. It is ideal for maintaining the rooting temperature in the tray and dome. It is very suitable for maintaining the required fermentation temperature in home breeding and is very suitable for temperature control of reptiles and small pets. The heating pad controller is compatible with all heating pads, but optimized for iPower seedling heating pads:

1. Digital temperature controller for heating pad

2. Provide a constant temperature for the living environment of specific crops

3. Specifications: 120V / 60HZ / 1000W

4. LED indicator light and three-hole grounding plug are easy to operate

5. Convenient LED heating and power indicator light allows you to check the status of the controller even in complete darkness

6.Can be used with iPower heat mat to make a warm and comfortable growth environment for your reptile even in cold winter



NOTE:

1. Do not immerse the digital controller or thermostatic sensor probe in liquid or very wet soil

2. Abnormal warning: If the thermostat displays "E1", it means the actual temperature is below 0 ° C or 32 ° F. If the thermostat displays "E2", it means the actual temperature is higher than 60 ° C or 108 ° F. If the thermostat displays "E3", it means the temperature sensor is not working properly, please reinstall the sensor.

Do not submerge Plug heat mat into thermostat Plug in thermostat power cord and set maximum desired temperature Heat mat thermostat can also be used to control the temperature of many other appliances as long as they don't exceed the maximum electrical specifications stated above. Simply place the sensors in the area where the temperature needs to be controlled plug the appliance into thermostat and set the desired temperature



INSTRUCTIONS:

1. To adjust the temperature setting, press and hold the "SET" button for 3 seconds to enter the temperature selection mode

2. To display in degrees Celsius, press and hold the "Down" button for 3 seconds press and hold the "UP" button for 3 seconds to display the temperature in Fahrenheit

3. Press the "UP" or "DOWN" button to adjust the temperature you want to set

4. Press the "SET" button again. This completes the set temperature

• Technical specifications: 120 volts/ 8. 3 Max amps /60 Hz/ 1000 Watts. Easy plug-in operation with LED illuminated indicator lights & three-prong grounded plug
• Temperature range: digital thermostat provides temperature control between 40 ° F-108 ° F (5-42 ° C). Temperature display range: 32 -140 ° F (0-60 ° C)
• Applicable occasions: used for seed germination, rooting, reptiles, home brewing and fermentation, providing a constant custom temperature to obtain the ambient temperature you need
• Ease of mind: handy LED heating and power indicator lights allow you to see the controller’s status even in total darkness
• Balanced temperature environment: set the temperature you need to get a uniform ambient temperature, so that your plants or animals are in a comfortable environment

User questions & answers

Question:	How to set temperature tolerance
Answer:	Read instructions
Question:	Is the probe waterproof? Will it rust in water
Answer:	They are NOT made for aquariums submerged in water but the tip is made of stainless steel so rust should not be a problem.
Question:	Will this work with heat lamps
Answer:	No heat mats only.
Question:	If i’m using a heat lamp on my bearded dragons tank, where do i put the prob? on the side of the glass or on the ground
Answer:	Definitely try and put the probe on the bottom of the enclosure, Make sure it's buried in his substrate so he doesn't get accidentally wrapped up in the wire. Also, make sure the wire is taped to the side of his enclosure as tight as possible for the same reason. I use under the tank heaters for my pythons, so trun the probe down the outside of.his enclosure and put.the probe between the bottom of his tank and the heater so there's no chance that he could get wrapped up in the wire .

Product features

Easy to Use

- Fahrenheit Light: It will be lighting when the temperature display in Fahrenheit.

- Celsius Light: It will be lighting when the temperature display in Celsius.

- Heating Light: It will be lighting when the output is working.

Switch Temperature Display

Adjust Temperature Setting

Product Specification

Germination Helper

iPower heat mats work perfectly on starting seed, even for beginners. They increase the success of seed starting by warming the root area 10-20 degree Fahrenheit over ambient temperature. The seeds will germinate better in a warm environment.

Terrarium Warmer

iPower heat mats is also applied in heating the pet terrariums. With the help of iPower Heat Mat Thermostat, the heat mats power can be controlled to provide a accurate temperature for your reptile pets.

DIY Your Brewing

Do you want to DIY a homemade wine? iPower heat mats working with the iPower Heat Mat Thermostat can control the heating for your wine containers to provide an accurate and appropriate temperatures to ferment.

Product description

Thermostat, heat, material- bi-metal (sensor), amperage rating- 13 amp, poles- 1, thermostat type- single pole model, voltage rating- 125 vac, temperature rating- -10 - 100 deg f, series- kt.

• Rugged Steel Case
• Voltage Rating: 125 VAC
• Temperature Rating: -10 - 100 DEG F
• Series: KT

User questions & answers

Question:	What are the dimensions of this item
Answer:	Yes.
Question:	Nrtl (nationally recognized testing laboratory) certification? (ul, etl, etc
Answer:	45~60 CM or 17.7 ~ 23.6 INCH. Thanks.
Question:	The one that we received measures the temperature (degrees) in celsius, not fahrenheit. do you have a unit that is in fahrenheit
Answer:	Mercury vapor in this reptile uvb uva heat lamp bulb.
Question:	can it be used exterior
Answer:	Any fixture with E26/E27 socket support 120V and size of the bulb(5.31 Inch Deep, 3.74 Inch Diameter), thanks.

Product features

TPI KT121 Industrial Series Thermostat, SPST Heat Only, 6' Cord/Plug

Thermostat, heat, material- bi-metal (sensor), amperage rating- 13 amp, poles- 1, thermostat type- single pole model, voltage rating- 125 vac, temperature rating- -10 - 100° F, series- KT.

About TPI Corporation

For over 69 years TPI Corporation has been known as America's Comfort Conditioning Company. TPI Corporation is an OEM manufacturer of electric heat equipment, process heat ovens, ventilation products & fans, lighting equipment, and custom thermostatic controls. TPI Corporation is a privately held organization provide quality products manufactured in the United States.

• ✓ MAINTAIN OVERALL HEALTH AND WELL-BEING OF REPTILES --- Habitats for these ectothermic animals must be kept within the Preferred optimum temperature range (POTR) to keep up with life in captivity. Heat is necessary for reptiles so that they’ll be able to reproduce, maintain a healthy immune system and have efficient blood circulation. Improper heating can make your herps susceptible to illnesses as it can negatively affect digestion, decrease appetite and may increase stress level.
• ✓ MULTIFUNCTIONAL WARMING TOOL --- Aside from providing an ideal terrarium temperature for your reptiles, this heat mat thermostat can be used for seed germination, aquarium, incubators, reptile enclosures, barbecue fermentation, and home beer brewing. Additionally, this device can be utilized to regulate the temperature of other appliances provided they don’t exceed maximum electrical specifications.
• ✓ PROVIDES CONTROLLED AND PRECISE LEVEL OF TEMPERATURE FOR TERRARIUMS --- As creatures that solely rely on outside sources to warm themselves, reptiles need to live in optimal temperature in their habitats. SunGrow Reptile Heat Controller can be used to maintain the required temperature in your herp’s environment. Its precise digital control feature makes it possible for users to closely control and monitor any kind of heat mat inside your bearded pet’s enclosure.
• ✓ EASY PLUG-IN OPERATION --- Easy to use with convenient plug and play design, it supports Celsius and Fahrenheit display with a temperature range of 5-40℃/ 42-108°F. It features LED illuminated indicator lights. Temperature can also be set by using the up and down button.
• ✓ UNIVERSALLY COMPATIBLE WITH ALL HEAT MATS --- With its three-prong grounded outlet, you can plug most heat mats, lamps or any warming device for your terrarium. Please note that heating equipment plugged into this thermostat should not exceed a total of 1000 watts.

User questions & answers

Question:	Does this item make a click sound when it turns the heating element on or off
Answer:	It does but it is not very loud. It does have a light that shows if it is heating or not.
Question:	Does this work with heat bulbs
Answer:	Yes
Question:	Does this have to be used with a heating mat or will it just tell me the temperature of the tank is it’s not connected to a mat
Answer:	It will read temp without a mat.. But for all that just buy a digital thermometer....and save a buck
Question:	Where do you put the prob for monitoring temp on heating matt
Answer:	Mine was on the center of the heat mat

Product features

A WORLD OF WARMTH

Reptiles are dependent on outside sources to warm or cool them. This is the reason why their habitats should have the proper temperature range. Failure to do so may result in serious illnesses or worse, even death. It is important to take note that before you even bring one home, it is necessary to set up the entire terrarium and heating system first. Ensure that your enclosure has a stable temperature for at least two weeks before placing your herp inside.

Reptile Heat Controller by SunGrow, when used with heat mats, can provide a controlled and precise level of warmth your pets require to thrive. They need to get a suitable temperature so that your bearded pets will be able to easily move its muscles to catch prey, escape form danger and properly digest food.

QUICK SET-UP & PROGRAMMING

With its Plug and Set installation process, you will be able to explore uncomplicated yet fully rewarding functional benefits of this thermostat. Below are simple steps to guide you during set-up:

MATERIAL & TECHNICAL SPECIFICATIONS:

• Material: ABS
• Color: Black
• Packaging: 1pc/Pack (Box)
• Size: 5.3” x 3” x 1.7”
• Wire length: 71“
• Power: 1000W
• UV: 120V
• Max Va：8.3A
• Temp：42-108°F (5-40℃)

Caution: Please keep away the probe or thermostat away from water.

Product description

Infrared Ceramic Reptile Heat Bulb:

Specifications:

Socket: E26;

Volt: AC 110-120V;

Watts: 100W;

Material: Ceramic, NiCrAl;

Diameter of heating surface: 85mm ;

Note: 1. Lamp surface temperature is too high, do not directly touch during it works; 2. Before remove it from fixture, please allow at least 1 hour for cool to avoid scald ; 3. Accidents may happen due to improper operation so please use it in a right way and avoid using in damp environment; 4. Please adjust the distance between the lamp and the pets, at least 35cm; 5. Please away from combustible or explosive materials；

Digital Thermostat Controller:

Specifications:

Temperature control range: 40℉-108°F;

Temperature display range: 32℉-140°F;

Rated Voltage: AC 120V 60Hz ;

Max Loading: 8A 1000W ;

Easy plug-in operation with LED illuminated indicator lights & three-prong ground plug. Digital thermostat can also be used to control the temperature of many other appliances as long as they don't exceed the maximum electrical specifications stated above. Simply place the sensors in the area where the temperature needs to be controlled plug the appliance into thermostat, and set the desired temperature.

Abnormal Warning: 1. If thermostat shows "E1", it means that the actual temperature is lower than 0℃ or 32℉; 2. If thermostat shows "E2", it means that the actual temperature is higher than 60℃ or 108℉. 3. If thermostat shows "E3", it means that the temperature sensor is not working properly. Please re-install the sensor；

• Temperature range: digital thermostat provides temperature control between 40 ° F-108 ° F (5-42 ° C). Temperature display range: 32 -140 ° F (0-60 ° C).
• Operating instructions: simple operation, with only three buttons, you can easily switch the temperature you need or unit of measurement. Handy LED heating and power indicator lights allow you to see the controller’s status even in total darkness.
• Perfect 24h heat source: heat bulb does not emit any visually detectable light, would not disturb pets sleep. 110-120V,100W, E26 lamp base. Material: ceramic, NiCrAl. To avoid scald, please wait at least 1 hour to cool down after turning off the bulb.
• High thermal efficiency: it emits infrared light without luminescence, and it also has a health care effect on animals while keeping warm，solid ceramic original.
• Package includes: 1-pack 100W ceramic heat lamp bulb, 1-pack digital thermostat controller.

Product description

Infrared Ceramic Reptile Heat Bulb: Specifications: Socket: E26Volt: AC 110-120VWatts: 100WMaterial: Ceramic, NiCrAl Diameter of heating surface: 85 mm Note: 1. Lamp surface temperature is too high, do not directly touch during it works. 2. Before remove it from fixture, please allow at least 1 hour for cool to avoid scald. ; 3. Accidents may happen due to improper operation so please use it in a right way and avoid using in damp environment. 4. Please adjust the distance between the lamp and the pets, at least 35cm. 5. Please away from combustible or explosive materials. Digital Thermostat Controller: Specifications: ; Temperature control range: 40-108°FTemperature display range: 32-140°FRated Voltage: AC 120V 60HzMax Loading: 8A 1000WEasy plug-in operation with LED illuminated indicator lights & three-prong ground plug The cord of the temperature probe and grounded three-prong plug is 6 feet ETL certification is proof that a product complies with widely-accepted safety standards Digital thermostat can also be used to control the temperature of many other appliances as long as they don't exceed the maximum electrical specifications stated above. Simply place the sensors in the area where the temperature needs to be controlled plug the appliance into thermostat, and set the desired temperature. Abnormal Warning: 1. If thermostat shows "E1", it means that the actual temperature is lower than 0 degree Celsius or 32. 0 degrees Fahrenheit. 2. If thermostat shows "E2", it means that the actual temperature is higher than 60. 0 degrees Celsius or 108. 0 degrees Fahrenheit. 3. If thermostat shows "E3", it means that the temperature sensor is not working properly. Please re-install the sensor. Clamp Light: Specification：Volt: 120VWatt: Accepts up to 150W bulb (E26)Reflector Diameter: 8. 5 inch Cord: 6 Feet 18/2 SPT-2 Cord UL Listed Clamp light can also be used as a table lamp in your room, garages or art studios, a work light in photography and workshops, amphibians and reptiles pets terrarium heat lamp, and even a growth light for indoor plants. Warning: The power cord on this product contains chemicals, including lead known to the State of California to cause cancer. Wash hands after use.

• Multifunction: great for reptile and amphibian terrariums, incubating poultry heater, heat bulb can increase blood circulation promoting health and healing.
• Perfect 24h heat source: heat bulb does not emit any visually detectable light, would not disturb pets sleep. 100W, E26 lamp base. Material: ceramic, NiCrAl. To avoid scald, please wait at least 1 hour to cool down after turning off the bulb.
• Multifunctional clamp light: scratch-resistant sleeves covered clamp would not leave marks on your surfaces, 360° adjustment and 8.5inch aluminum reflector can focus light where you need. Volt: 120V, Watt: 150W (E26). have convenient on/off button.
• Temperature range: digital thermostat provides temperature control between 40-108℉, temperature display range: 32-140°F. Support Celsius or Fahrenheit readout. Volt: 120V 60Hz; Max Loading: 8A 1000W. Do not immerse controller or probe into water.
• Package include: 1-pack 100W ceramic heat bulb, 1-pack digital thermostat (easy plug-in operation with LED illuminated indicator lights and three-prong grounded plug), 1-pack clamp light with 8.5 inch reflector.

User questions & answers

Question:	How long does this take to heat up? After an hour its still not getting hot
Answer:	They do vary in size but it is a large bag and last quite some time depending on how much you feed your dragon. I would not just feed your dragon these. Give them a varied diet of fruits, vegetables and protein such as meal worms and crickets.
Question:	Should this che be put on a dimmer or a thermostat for reptiles
Answer:	Yes, they have the same nutritional value as live crickets. I feed them to My Bearded Dragon once or twice a week and he likes them but prefers the meal worms.
Question:	is this with boa constrctor
Answer:	its straight calcium, no expiration date on this
Question:	What is the temperature range? Can you use this for baby duckling
Answer:	D3 cannot be digested properly and can build up in your reptiles' system and kill them, as for licked from a bowl - not sure about that but you dust them on crickets and your type of worm food and they ingest it like that.

Product features

Specifications

• Socket: E26
• Voltage: AC 110-120V
• Watts: 100W
• Material: Ceramic, NiCrAl
• Color: Black
• Diameter of heating surface: 85 mm
• Height: 100 mm
• Package Includes: 1-pack 100W ceramic heat bulb

About Clamp Light

1. Supply powerful light anywhere you require it with this 8.5" Clamp Light.
2. It is constructed with a scratch-resistant vinyl sleeve and a spring-powered steel clamp with an adjustable ball joint, which allows you to easily position the lamp almost anywhere.
3. The lamp includes an easy to use, energy efficient on/off switch that saves energy.

• Volt: 120V
• Watt: up to 150W
• Reflector Diameter: 8.5 inch
• Lamp Type: type A lamp (E26)
• Cord: 6 Feet
• Material: Aluminum

Easy to Use

• Fahrenheit Light: It will be lighting when the temperature display in Fahrenheit.
• Celsius Light: It will be lighting when the temperature display in Celsius.
• Heating Light: It will be lighting when the output is working.

NOTE: Please note that the controller can only be used to power off heating equipment at setting temperature and does not increase the heating power of the heating equipment

Product description

Infrared Ceramic Reptile Heat Bulb:

Specifications:

Socket: E26;

Volt: AC 110-120V;

Watts: 150W;

Material: Ceramic, NiCrAl;

Diameter of heating surface: 85mm ;

Note: 1. Lamp surface temperature is too high, do not directly touch during it works; 2. Before remove it from fixture, please allow at least 1 hour for cool to avoid scald ; 3. Accidents may happen due to improper operation so please use it in a right way and avoid using in damp environment; 4. Please adjust the distance between the lamp and the pets, at least 35cm; 5. Please away from combustible or explosive materials；



Digital Thermostat Controller:

Specifications:

Temperature control range: 40℉-108°F;

Temperature display range: 32℉-140°F;

Rated Voltage: AC 120V 60Hz ;

Max Loading: 8A 1000W ;

Easy plug-in operation with LED illuminated indicator lights & three-prong ground plug. Digital thermostat can also be used to control the temperature of many other appliances as long as they don't exceed the maximum electrical specifications stated above. Simply place the sensors in the area where the temperature needs to be controlled plug the appliance into thermostat and set the desired temperature.

Abnormal Warning: 1. If thermostat shows "E1", it means that the actual temperature is lower than 0℃ or 32℉; 2. If thermostat shows "E2", it means that the actual temperature is higher than 60℃ or 108℉. 3. If thermostat shows "E3", it means that the temperature sensor is not working properly. Please re-install the sensor；

• Temperature range: digital thermostat provides temperature control between 40 ° F-108 ° F (5-42 ° C). Temperature display range: 32 -140 ° F (0-60 ° C).
• Operating instructions: simple operation, with only three buttons, you can easily switch the temperature you need or unit of measurement. Handy LED heating and power indicator lights allow you to see the controller’s status even in total darkness.
• Perfect 24h heat source: heat bulb does not emit any visually detectable light, would not disturb pets sleep. 110-120V,150W, E26 lamp base. Material: ceramic, NiCrAl. To avoid scald, please wait at least 1 hour to cool down after turning off the bulb.
• High thermal efficiency: it emits infrared light without luminescence, and it also has a health care effect on animals while keeping warm，solid ceramic original.
• Package includes: 1-pack 150W ceramic heat lamp bulb, 1-pack digital thermostat controller.

User questions & answers

Question:	Can i use this inside my chicken coop? we have baby chicks and want to use inside small chicken coop (separate from the hens
Answer:	Good price fast delivery then. But not now. Packages bring shipped by mail. Not ok
Question:	Where is it made
Answer:	I use this bulb for my bearded dragon, we also have a 100w. So you can use both.
Question:	How far does the heat reach i have 36×18×36 enclosure
Answer:	I would read on what kinda heat it needs. My tortoise needs 80-90 ° So I got a 100 watt bulb. I live in a apartment and I use my central air so my house is cold. When I turn off the ac I use a 75 ° bulb and I get 80 °. I use a regular bulb during the day and a night bulb (purple) during the night these are less stressful for the reptiles. Make sure you have a thermometer and it is put somewhere it can get a accurate reading if your light is too low it cold be too hot if it's to high it cold be colder. Hope this answers your question.
Question:	will this fit a 5.5 inch heat lamp
Answer:	It can. Did not have good luck with these. Very short life.

• 【WiFi-Enable】Inkbird Smart Temperature Controllers support WiFi connection and control.
• 【APP Features】Temp graphs, alarms, ℃/℉ switch & timer. All can be set through the Inkbird Pro app.
• 【Double Outlets】Supports plug-in 2 heating devices, like 2 heaters(1200W 10A Max).
• 【Digital Displays】Both the measured temp & set temp are displayed on Inkbird temperature controller.
• 【2 Cycle Timer】Inkbird ITC-306T temperature controller supports 2 cycle timer in 24 hours.

• PROFESSIONAL RELIABILITY AND RESULTS: Regulates and maintains your preferred temperature within a control range of 40–108 ºF（ Temperature display range is 32 -210°F）; perfect for professional horticulturalists or the budding grower. Comes with a sensor probe so you can reliably track the temperature of your plant’s roots
• HIGH-QUALITY CONSTRUCTION: With an easy-to-grip hexagonal shape and made of an extra-fortified plastic, components will not rust or malfunction under tough conditions
• ZERO-EFFORT SET UP & OPERATION: The controller comes with a manual but you won’t need to read it! Using just 3 buttons, you can set a temperature or change the display between Fahrenheit/Celsius in seconds
• USE, HANG, FORGET: Our controller comes with a hanging tab and wall mount along with a convenient angled socket to keep cords untangled and neat. Guaranteed to keep your growing operation perfectly balanced, as all things should be
• COMPATABILITY & SAFETY GUARANTEED: Compatible with any heat mat and ready to plug in to North American outlets. VIVOSUN always stands behind its products and cares for you—if you have any questions or concerns contact our friendly customer service staff

User questions & answers

Question:	Is the probe ok with saltwater
Answer:	Instructions state "do not immerse temp probe in liquid" so no .
Question:	how to switch from °F to °C
Answer:	Hold down on the up and down buttons at the same time
Question:	Is this a thermostat with a mat or does it work with any other mat
Answer:	It is just a thermostat. It works with anything heat outputting, like a heating lamp. The probe senses the temperature and turns the power on or off to whatever you plug into it.
Question:	how many mats can be connected to this
Answer:	There is only one outlet on the thermostat. However, being that the thermostat is rated for 1000 watts, you can connect a power strip and connect multiple heating mats provided you do not exceed the units power rating. Just to be safe, I wouldn't plug in more than half the rated power (i.e. 500 watts). But for those 17 watt heating mats, that's a lot of mats!

Product features

Digital Seedling Heat Mat Thermostat Controller

• The easy-to-grip hexagon controller is made of extra-fortified plastic and high-quality components that won’t malfunction under tough conditions.
• Clear, minimalist display, detailed finishing, smooth edges, and tactile buttons demonstrate the controller’s superior craftsmanship.
• Compatible with standard North American outlets and plugs: the secure-fit 3-prong grounded socket grips plugs tightly.
• Electrical specs: 120 Volts/60 HZ/8.3 max Amps/max Wattage 1,000 W.

Hanging Tab

Hang the controller however you want from the eyelet tab. It can hang flush with the wall or from a variety of hook sizes.

Power Cord and Sensor

Enjoy more installation flexibility with a 5.8FT power cord and 6.4FT probe cord. It is ideal for where you have it located (no where near a plug).

3 Prong Outlet

The angle of the outlet keeps cords from getting tangled. This UL certified 3 prong grouded outlet support a 1000Watt load.

Suction Cup

The adjustable suction cup lets you easily stick the thermostat probe to a wall or terrarium.

Germination Kit

Combined with VIVOSUN thermostat, put the probe into the seed trays. It helped facilitate a 100% germination rate and you will find all your seeds germinated faster then before.

Reptile Warmer

Can be used with VIVOSUN heat mat to make an warm and comfortable growth environment for your reptile even in cold winter.

Fermentation Helper

It is perfect for your set up to keep wine or kombuchat at a perfect temperature. With VIVOSUN thermostat controller,you don't have to make sure its overheating.