14 best 3d printer electronics board

Product description

3D printer Kit guide: http://osoyoo.com/driver/3D%20printer%20instructions.pdf 

Caution: 

1) The max power supply for these ramps is 12V and the max watts is about 180W. The max watts for the hotbed is about 100W and the max temperature is just 50 degree Celsius. 

2) Do not plug or unplug and wire or module when power is on, do not even touch the board when power is on or your hand has static charge(you can remove static charge by touching metal tap) . 

3) Always double check power wire is properly installed. If you do not follow above move, you may damage the control board and your 3D printer. 

4) Pls confirm the A4988 driver install correctly on Ramps1.4 board. 

5) The endstop pins are Signal-GND-VCC, instead of VCC-Signal-GND like the rest of RepRaps boards. Make sure to wire them correctly. This is done to allow squeezing fatter traces on the printable board.

6) Don't secure Arduino/Ramps with conductive screws through both mounting holes. The screw may cut into the positive trace creating a HIGH current short.

7) Test all electronics thoroughly before placing into service.

8) Do not leave power supplied to electronics unattended, or run machines unattended due to the risk of fire and malfunction.

9) Once you start putting electricity into your RepRap - even at just 12 volts - you have to take basic, common sense precautions to avoid fires. Just in case these fail. test your workshop smoke detector.

Product Specification: 

1) Marlin firmware update: Arduino IDE 1.5.X 

2) This kit consists of a RAMPS 1.4 shield, an Mega 2560 board, five Stepper drivers and a LCD. It can control up to 5 stepper motors with 1/16 stepping precision and interface

User questions & answers

Question:	My makerbot Z18 driverboard is burnt and not avalible. Could this kit be installed in my cabnet and drive the motors
Answer:	This memory card is "Detroit Packing Co." branded. It is not "Nintendo" branded.
Question:	i cannot seem to get this working all steppers are inserted correctly the lcd is connected correctly the board comes on but the lcd just lights upblan
Answer:	First I booted up with the empty card. after windows installed it, I shut my computer down and pluged in my ssd drive. then started up in cmos, to see if it was their, it was. Every thing booted fine. So i ran a speed test and found that it ran 60% slower than my 1.5 onboard sata. Even though it showed as a 6g it does not have the speed. So i now use it for my cd rom. I there is some settings i missed, sure would like to know.
Question:	Hi there, - do you happen to have the schematic on how to set/connect everything up? - where can i download software/drivers? - i am trying to build
Answer:	Sorry, the two slots are NOT standard USB slots. Although, they may look similar they are not. They are both eSATA ports, a kind of USB hybrid. Used to connect external drives. They are faster than USB or the older fire-wire. Look for an external hard drive that uses eSATA. For speed, eSATA is a huge jump over USB. It can be as fast as adding a hard drive straight into your computer.
Question:	my lcd wont come on too tried everything any solution. or any link to the right firmware
Answer:	Updating this answer for modern motherboard and more modern kernels. No, it is not plug-and-play. This card does not support AHCI specification 1.3.1, finalized in 2014, which means it will not work with most modern motherboards, or at least fully. WIth Linux, there is a sort of work-around though, you can set iommu=soft on the grub line (/etc/defaults/grub on Ubuntu and Debian-based). iommu=soft tells the kernel to ignore some of the ATA errors that result due to the failed AHCI commands. Still, if you want a fully working card in modern Linux and hardware, this is not it. Look at LSI.

Product description

Item Type: 5 inch LCD Screen Kit



Resolution: 800×480 pixels



Features:

5V power from host 3D printer controller

2-wire async serial interface with 3.3V signal level (5V tolerant input)

Connections to the external SD card socket that is included on most compatible displays is available via a 10-way ribbon cable connector on version 2.0 PanelDue boards

4-wire cable to connect the PanelDue to your controller board for the serial and power connections



Packge:

1PC * 5" Color Touch Screen

1PC * Cable



Note: Color shading for different monitor settings

• The control board and firmware support size: 5"
• Compatible with DuetWifi Advanced 32 Bit Electronics for 3D Printer, 3D Printing Electronics and CNC Machines
• 5V power from host 3D printer controller, 2-wire async serial interface with 3.3V signal level,.Wire cable to connect the PanelDue to your controller board for the serial and power connections
• Connections to the external SD card socket that is included on most compatible displays is available via a 10-way ribbon cable connector on version 2.0 PanelDue boards
• After-sales Guarantee: each one defective item can have free replace or refund, If need further please feel free to email or Q&A us, we and our engineers are very happy to assist you.

Product description

Specifications:

Brand: Anet

Suitable for: Anet A8 3D Printer

Voltage Input: 12V

Mainboard Size: 10 * 9.5 * 2cm / 3.9 * 3.7 * 0.8in    

Mainboard Weight: 63g / 2.2oz

Package Size: 12 * 11 * 3cm / 4.7 * 4.3 * 1.2in

Package Weight: 80g / 2.8oz



Package List:

1 * Mainboard



Note:

Please pay more attention to the circuit diagram showed in the picture before mount it.

User questions & answers

Question:	Will this work for a prusa i
Answer:	I don't know about High Sierra, but I believe it should. This card is working great on a Mac Pro 2010 with the latest firmwares using Mojave OS. Speeds are around 300 Mb/sec. One caveat though, if you connect more than one device to the usb port, the speed decreases.
Question:	Can this board be upgraded to Marlin? If so which Guide works best for this board
Answer:	Hello. Regrettably, unless Windows is being run in a virtual environment, this will not work on windows via Bootcamp on a Mac Pro.
Question:	Does this product have a USB port
Answer:	Hello, yes this card would work with Windows 7 and would need a driver in order to work which can be found here https://support.frescologic.com/portal/en/kb/articles/latest-drivers
Question:	If i buy a 3d printer mainboard, is there a video tutorial, or manual? i'm afraid i do not know how to install it
Answer:	Hello! USB 3.0 was renamed to USB 3.1 gen 1, which is the standard the card is built to. This would be limited to the 5Gbps. USB 3.1 gen 2 is capable of 10Gbps, but we do not currently have a card that supports that.

• Upgraded Silent Mainboard V4.2.2: Ender 5 Pro 3d printer comes with upgraded V4.2.2 silent Mainboard with TMC2208 drivers, allowing for quieter and more precise printing performance.
• Metal Extruder Kit: Ender 5 Pro adopts Creality metal extruder which has better stronger pressure to pushing filament into printer nozzle, improving the printer's performance.
• Capricorn Premium XS Bowden Tubing: Imported Capricorn blue tube with high temperature resistant makes feeding smoother and ensure great printing texture.
• Brand Power Supply: Built-in brand power supply, heat up the hot bed to 110℃ in 5 minutes.
• Semi-Assembled Kits: Ender 5 Pro comes with several partially assembled kits, very easy to assemble and allow you to learn about the basic construction of 3D printer. OFFICIAL SERVICES: Comgrow team provides you lifetime technical assistance and 24 hours professional customer service.

User questions & answers

Question:	Does Ender 5 come with Slic3r configuration file
Answer:	Mine came with one for Cura on the SD card. On the card in the "2.Software and USB Driver\CURA\Cura3.4.1" directory there is a file named creality_Ender5.def.json. I installed the newest Cura (3.6 as of writing this) and copied the file to "C:\Program Files\Ultimaker Cura 3.6\resources\definitions" (if you're using windows, v3.6, and the default install location) and the profile for the Creality Ender-5 was there to select when I started Cura.
Question:	Does this printer read stl or do i have to write g code
Answer:	It reads g-code. If you use a slicer program like Cura Ultimaker, it will slice the model and write the g-code. You can then, using the SD card, import it to your printer!
Question:	In the description for the 5 pro, it says it comes with upgraded motherboard as V1.1.5 as well the V4.2.2 . So which one does it come with currently
Answer:	V.1.1.4 is the mother board with the basic ender 5. It is not a silent motherboards which is one of the upgrades. It also has fixed glitches that the origional ender 5 has. Not sure what else is different except faster processes
Question:	Where can you get the glass bed for this? when i search i only see the ender 3 and ender 3 pro. will that work on the ender
Answer:	The glass bed for the ender 3 is the same bed for the ender 5. The bed isn't printer specific, they are sold by size. Since the x and y build area are the same for the 3 and the 5, the glass bed is the same. 235mmx235mm

Product features

Upgraded Silent Motherboard V4.2.2

Ender 5 Pro is the upgragded version of Ender 5. There are THREE components that are listed below have been improved.

> Upgraded Silent Mainboard V4.2.2 with TMC2208 drivers, allowing for quieter and more precise printing performance.

> Metal Extruder Frame is stable in feeding in filaments and wear-resisting, hence, we get better printing quality.

> Imported Capricorn Bowden PTFE Tubing.

Metal Extruder Kit

Ender 5 Pro adopts Creality metal extruder which has better stronger pressure to pushing filament into printer nozzle, improving the printer's performance.

Capricorn Premium XS Bowden Tubing

Imported Capricorn blue PTFE tube with high temperature resistant makes feeding smoother and ensure great printing texture.

Brand Power Supply

Built-in brand power supply, heat up the hot bed to 110℃ in 5 minutes.

Y axis with dual shaft

Y axis with dual shaft, which makes the output more stable, effectively solve the problem of shock imbalance caused by printing for a long time.

220X220X300 Printing Size

220X220X300 Printing Size,implement more printing requirements, creat multiple models.

Removable Building Surface

Ender 5 Pro comes with removable building surface, which makes the models to be removed more easily.

• Meanwell Power Supply: Ender 3 Max comes with UL Certified power supply which with a stable output ensuring the temperature fluctuations are minimized and protecting your printer from unexpected power surges. It can heat the hot bed to 110℃ in around 10 minutes.
• Tempered Carborundum Glass Platform: Enable the hotbed heat up quicker and prints adhere better without the warping. Ultra smoothness even on the first layer.
• All Metal Extruder, Filament Detector, Dual Cooling Fans in Hot End Kit 2 Sides : promotes better printing result, prevent filament wasting and reduces filament blockage
• Silent Motherboard. Backed by TMC2208 silent driver, reduce noise and wobbling during printing, smoother motion and quieter printing process.; BL touch installation also is available(not included in package, you can buy one if you need. Please flash firmware first if you use a BLTouch).
• Quick Installation: Creality ender 3 max comes almost assembled, which is much easier to assemble than Ender 3. You only need to spend few minutes to attach the gantry with four screws, the screen, filament spool holder, portable handle and plug in some wires.

User questions & answers

Question:	what motherboard is in this one 4.22 or
Answer:	I can not speak specifically on the MakerBot since I don't have one but I will say that this kits components have become a standard used in all types of printers around the world in my opinion... The 2560 and ramps board setup has been a proven option in the 3D Printer community for a long time now. I am using mine on a large format printer build from scratch and I am recording the progress on YouTube. You can see how I am using the kit at PaPaw'sProjects... I don't think you can go wrong... Good Luck!
Question:	Which bl touch works for this
Answer:	if you are using Marlin, you need to define the display correctly and include the display library. If you think you have that right in the firmware, try switching the cables. If you have them backwards, the display will take two to three seconds for the backlight to turn on but you will get a blank screen. Power down, switch them, and power back up. If your backlight comes on almost immediately but the display is still blank, you have the cables right need to fix something in the firmware.
Question:	How hot can the hotend get
Answer:	Ramps1.4 3D printer circuit connection graph: http://osoyoo.com/2016/07/03/reprap-3d-printer-circuit-connection-graph/RAMPS 1.4 3D printer board Marlin firmware installation guide: http://osoyoo.com/2016/06/29/ramp1-4-board-for-reprap-3d-printer-firmware-installation-guide/
Question:	Is it prebuilt
Answer:	Arduino based Marlin firmware

Product features

Generous Print Volume

300*300*340mm printing size is larger ender 3, ender 3 v2 and ender 5.

Branded Meanwell Power Supply

Safe and secure. 350W-24V meanwell power supply ensure fast heating up the hot bed.

Models Are Removed More Easily

Add a tempered glass plate above hot bed. Better adhesion, easier removal after cooling and less wrapping.

DIY BLTouch Installation

It has reserved room for BLTouch bed-leveling probe, you can install it yourself if you wish. NOTE:BLTouch is not included in package. Please flash firmware version first if you need to use BLTouch.

Foldable Filament Holder

This filament mount can be rotated 90 degrees in one direction, can save space and make your desktop utilization higher.

Resume Printing Function

The machine can automatically resume printing after power-offer or filament breakage. Less worries on print failure.

Product description

Features:

1 Two-phase stepper motor single-phase current 1.2A (peak value is 2.0A) Motor operation can be adjusted 2 Support Step/DIR interface and SPI interface two control methods

3. Motor input voltage range: 4.75-36V

4. The input voltage of the logic interface is: 3-5V

5 subdivided into 256

6. Noise-free operation combining efficiency and motor torque

7 High-precision sensorless motor load detection

8. Reduce energy consumption by 75%

9, high load drive is not out of sync

TMC2208 single-axis stepper motor driver chip, power tube built-in drive current 1.4A peak current 2A, voltage range

4.75V-36V, 256 subdivisions; with patented technology spreadCycle high chopping frequency, dcStep locked rotor detection technology, coolStep current dynamic adjustment technology, can save 70% energy

Flexible microPlyer interpolation unit, the module can provide up to 256 microsteps/step resolution, even at pulse speed

Sinusoidal control can still be achieved in systems with limited rates; due to stealthChop fine tone technology is widely used in 3D printing

Use, so the design of these components is also compatible with existing 3D printer electronics, eliminating the costly cost of redesign

use. Both components have pulse/direction inputs and can be operated completely autonomously. Configuration is achieved via digital input.

Can replace the original TMC2100 with lower calorific value

Shipping list:

TMC2208 drive module, 1 block

Heat sink, 1 piece

Potentiometer adjustment screwdriver, 1

• TMC2208 is an ultra-quiet two-phase stepper motor drive chip, continuous drive current 1.4A, peak current 2A, voltage range 4.75V-36V, 256 subdivision.
• The flexible microPlyer interpolation unit provides up to 256 subdivisions, allowing perfect sinusoidal control even in systems with limited pulse frequencies; these are also designed because stealthChop2 ultra-quiet technology is widely used in 3D printing.
• Compatible with existing 3D printer electronics, eliminating the expensive costs of redesign. It can replace the original TMC2100 A4988 DRV8825 LV8729, lower heat, especially for 3D printing market.
• With this adapter you can test your SilentStepStick or flash the TMC2208 SilentStepStick with an USB-to-serial converter.
• Setting Method: With the TMC2208 Configurator you can change the settings and program the OTP (One-Time-Programmable) memory of a Trinamic TMC2208 via the UART interface.

Product description

Description:



Specification:

CNC Shield Board:

1.PWM Spindle and direction pins

2.4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)

3.2 x End stops for each axis (6 in total)

4.Coolant enable

5.Uses removable A4988 or DRV8825 compatible stepper drivers

6.Compact design

7.Stepper Motors can be connected with 4 pin molex connectors or soldered in place

8.Please note that this is an unassembled kit and Basic soldering skills are needed



DRV8825 Stepper Motor Driver:

1.A simple steps and direction control interface

2.Six different steps resolutions: full step, half step, 1/4-step1/8-step1/16-step, 1/32-step

3.CAN interface directly with 3.3 V and 5 V systems

4.Over-temperature thermal shutdown, overcurrent shutdown, undervoltage lockout

5.Short to ground short circuit load protection



Board for Arduino:

1.MCU: ATmega328

2.USB interface: ATmega16U2

3.Operating voltage: 5V

4.Digital I/O pins: 14 (including 6 with PWM capability)

5.Analog input pins: 6

6.I-I/O pin output current: 40mA max

7.3.3V output current: 150mA max

8.Flash memory: 32kB (0.5kB used by bootloader- included)

9.Static RAM (SRAM): 2kB

10.EEPROM: 1kB

11.Clock speed: 16MHz



LCD 2004 Smart Controller:

Easy connect it to your Ramps board using the "smart adapter" included.



Package included:

1 x CNC Shield Board Ramps 1.4

1 x Board for Arduino

1 x LCD 2004 Smart Controller

1 x L type adapter plate

2 x FC cable

5 x DRV8825 Stepper Motor Driver

5 x Heatsink

6 x Endstop Mechanical Limit Switch with Cables

• 3D Printer Accessories Set meets most needs. Including CNC Shield V3.0, Board for Arduino, A4988 StepStick Stepper Motor Module.
• The 3D printer stepper motor shield V3 can be used as driver expansion board for engraving machines and 3D printers.
• It has in total 4 channel slots for DRV8825 stepper motor driver modules for driving 4 channel of stepper motors.

User questions & answers

Question:	What stepper driver come with this kit
Answer:	yes,of course.this item included manual and you can watch the video on youtube.

• Duet 2 Wifi is an advanced 32 bit electronics for the control of 3D printers and other CNC machines. It has the same features as the Duet 2 Ethernet other than providing a WiFi connectivity rather than etherne;Tips:This board is a little complication, if you are begineer, we don't suggest you order it.
• Reproduction/modification is not endorsed or supported in any way by Think3dPrint3d or Escher3d".
• Support network function, Dedicated Wifi module, connect via PC, tablet or smartphone on the same network to the on board web interface.
• Powerful 32 Bit Processor, improve its performance highly.（Please note:did not comes with SD card,you need to buy it by yourself, thanks for your understanding)
• After Sales Guarantee: each one defective item can have the free replace or refund, need more help please feel free to contact us, we and our engineers will try our best to assist you.

User questions & answers

Question:	Will this operate on 24v power supply (ender 3 pro) without a dc buck-boost
Answer:	Yes. I run on 24V. You can verify by looking at the diagram for VIN (power in). It specifies the range of 12V to 25V.
Question:	How is this better than using a Raspberry Pi
Answer:	This is a printer controller board, a Raspberry Pi isn't...
Question:	What are the drivers? Are they 2080? Is this a good replacement for the Creality boards
Answer:	Super quiet TMC2660 stepper drivers, up to 256 microstepping, creality boards is A4988 driver, more noise. so It is good replacement for creality boards.
Question:	Are the dimensions and mounting holes the same as the genuine Duet 2 Wifi so I can use the same printed case
Answer:	Yes the dimensions and connector layout are the same.

Product features

1. How to Connect Wifi to Duet 2 WiFi V1.04?

Step 1: Create a new file named "startwifi" in the macros folder of the SD card with content of M552 S1, which you could use to connect the wifi directly by clicking it.

Step 2: Star the WIFI with M552 S1

Step 3: Remember the wifi account and password with M587

Finshed: Select “ Startwifi” as soon as the board starts, it will connect the wifi directly.

3.How to Wire Cooling Fan in Duet 2 WiFi V1.04

Please pay attention to the voltage of your fan and make sure that the wiring of your fan is in the right place referring to picture.

Wiring of Duet 2 Wifi V1.04 and BL-Touch

Basic usage of the duet 2 wifi are listed above.

If there is still some doubt for your usage, we are right here to assist you.

• TMC2208 is an ultra-quiet two-phase stepper motor drive chip, continuous drive current 1.4A, peak current 2A, voltage range 4.75V-36V, 256 subdivision.
• The flexible microPlyer interpolation unit provides up to 256 subdivisions, allowing perfect sinusoidal control even in systems with limited pulse frequencies; these are also designed because stealthChop2 ultra-quiet technology is widely used in 3D printing.
• Compatible with existing 3D printer electronics, eliminating the expensive costs of redesign. It can replace the original TMC2100 A4988 DRV8825 LV8729, lower heat, especially for 3D printing market.
• With this adapter you can test your SilentStepStick or flash the TMC2208 SilentStepStick with an USB-to-serial converter.
• The adapter comes with stackable headers, so you can use it direct on your 3D printer board. The tester is pre-configured for standalone operation on an USB to serial adapter (VIO-VM jumper closed).

User questions & answers

Question:	UART mode ready? or it needs furter modification
Answer:	It is prebuilt to 4 parts and you just need spend few minutes to build it.
Question:	How tall are the heatsinks
Answer:	It is similar to the anet a8 it might work
Question:	will they work for a10m
Answer:	Yes, this board can be upgraded to Marlin. I currently have the board running Marlin 1.1.8 without an issue. As for guide, I'm not quite sure what you mean, but to install Marlin on the board I wa5ched a YouTube video by Joe (3DMN) to assist-pretty sude it was a video about addint the BLTouch.
Question:	When i set the direction pin high, the motor works exactly like it should. when i set the direction pin low, the motor doesn't work at all. why
Answer:	It has the standard USB 2.0 Printer Port.

Product features

3D Printer Stepper Motor Driver

MC2208 V1.2 is an ultra-quiet two-phase stepper motor drive chip

continuous drive current 1.4A

peak current 2A

voltage range 4.75V-36V

256 subdivision

The flexible microPlyer interpolation unit provides up to 256 subdivisions, allowing perfect sinusoidal control even in systems with limited pulse frequencies

These are also designed because stealthChop2 ultra-quiet technology is widely used in 3D printing

Specifications :

Interface: Step/Dir

Configuration: CFG Pins or UART

Native Microsteps: up to 1/256

MicroPlyer Microsteps: 1/256

Logic Voltage (VIO): 3-5V

Motor Voltage (VM): 4.75-36V

Motor Phase Current max: 1.2A RMS, 2.0A Peak

Note :

TMC2208 V1.2 driver needs extra fan to cool it, otherwise the high temperature may destroy it.

Don't connect the motor when measuring the voltage, otherwise it is easy to burn the driver.

Power should be connected when measuring voltage, do not just connect USB power supply.

Package Includes:

5 X TMC2208 V1.2 Stepper Motor Driver

5 X Heat Sink

1 X Screwdriver

Product description

Description:



Specification:

3D Printer Controller Board RAMPS 1.6:

1 It can be extended to LCD and other parts.

2 There are heater and fan MOSFET outputs and 3 thermistor interfaces

3 5A additional security and component protection fusion

4 Heated bed controls additional 11A fuses

5 Applied to 5 stepper drive board

6 Design of plate pin socket can be easily replaced or removed for future design

7 I2C and SPI pins are available for future expansion

8 Servo connectors are used for connecting limit stops, motors and light-emitting diodes. These connectors are gold-plated and have a rated current of 3A, which is very compact.

9 The LED will light when the heater has output

10Choose 2 motors to connect to Z Prusa Mendell



A4988 Driver:

Simple step and direction control interface;

Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step;

Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated;

Voltage to achieve higher step rates;

3.3 and 5 V compatible logic supply

Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay);



Board for Arduino:

Operating Voltage: 5V

Input Voltage (recommended):7-12V

Input Voltage (limits):6-20V

Digital I/O Pins: 54 (of which 14 provide PWM output)

Analog Input Pins: 16

DC Current per I/O Pin: 40 mA

DC Current for 3.3V Pin: 50 mA



Package included:

1 x RAMPS 1.6 Board

1 x Board for Arduino

1 x 12864 LCD Display Controller

1 x LCD Smart Adapter

5 x A4988 Stepper

1 x 40pin Dupont Cable Female to Female

1 x 40pin Dupont Cable Female to Male

• 【Upgraded Version】same structure as Ramps 1.5, have new 2pin connectors, have a good Heatsink above MOS tube in order to give a better function to heat dissipation, the Power is larger, the largest power will be up to or 270W.
• 【12864 LCD】The intelligent controller includes an SD card reader, rotary encoders and a 20-character × 4 line LCD display. You can easily connect it to your RAMPS 1.6 board using "smart adapter" included.
• 【Board for Arduino】Operating Voltage: 5V, Input Voltage (recommended):7-12V, Input Voltage (limits):6-20V,-Digital I/O Pins: 54 (of which 14 provide PWM output)
• 【Package include】 1 x RAMPS 1.6 Board,1 x Board for Arduino,1 x 12864 LCD Display Controller,1 x LCD Smart Adapter,5 x A4988 Stepper,1 x 40pin Dupont Cable Female to Female,1 x 40pin Dupont Cable Female to Male

User questions & answers

Question:	Can you run 2 stepper motors from the z axis output
Answer:	The highest hot end temperature of hot end is 260 degree but we don't suggest to print at the highest temp. PLA printing temperature is 195-210.

• ★All in one-piece design and solid stable black metal frame with quickly user interface touchscreen controls and easy replacement filament spool.
• ★Strong adhesion flexible BDG heated print-bed, no worry of first layer's adhesion, easy to remove the model and no masking tape needed.
• ★Self-developed motherboard, upgraded filament sensor and strong memory print function - filament run-out detection which allows you to know when you should change the filament and resume print from where the print was stopped by power failure or accidently sd card out.
• ★Support 1.75mm ±0.03 PLA/ABS filament and compatible with STL, OBJ, G-Code format. Moreover Cura(Win/Linux/Mac)/JGcreat(Windows 64bit) software are supported.
• ★SD card and USB connectivity, easy operation. State: All items out are tested by our professional engineer strictly, good performance and out. As owner of JGmaker diy 3d Printer, professional technology and best after-sale service are guaranteed.

Product features

JGMAKER Large 3D Printer A5S 305x305x320mm

• Layer thickness : 0. 1-0. 3mm
• Filament Diameter: 1. 75mm
• Print speed：10-150mm
• nozzle diameter: 0. 4mm
• Machine weight: 13. 8KG
• Packing weight:16.8kg
• Packing size:26*24*11in
• Resume print : yes
• Filament run out detection: yes
• Colorful touch screen: yes

Modular assembly,easy and fast assembly

A5S comes with three big modulars : the frame, the Y-axis box and filament holder, simple construction of the whole machine.

You only need to assemble a few screw, less than 30 minutes to build the printer

360° Sheet Metal Frame

All-in-one design,stable and durable sheet metal frame, delicate and simple, 1 minute fast assemble, quick user interface touchscreen, offering great UI experience.

Filament run out detection

Filament run out detection: The machine beeps when your filament runs out to allow you to change the filament and avoid a failed print

Resume Printing

Power Failure Protection: resume printing from where the last print was stopped due to power failure.

Save your time and cost

Big Build Area

Build area: 305mm*305mm*320mm

With small machine size, while getting a big build area. Enjoy your printing.

Product description

Feature:

7. Both the in-line driver jack and the external drive port are included, more expandable and more selective.

8. Compatible with a variety of drivers and special modes (the uart mode of the TMC2208, the SPI mode of the TMC2130, etc.), with a dedicated port reservation, and the wiring settings are more concise and convenient.

9. Support a variety of open source firmware, continue the smoothieware firmware used in the original s series motherboard, for SGen-L can also support the marlin2.0 version of the firmware.

10. High-quality circuit boards are used, and the corresponding pins of each interface are marked with silk marks, making it easier to identify and modify.

11. A dedicated power chip is used to support 12V-24V power input.

12. Support LCD 12864, MINI12864 and other control panels for display control.

13. Can be used with the full range of MKSTFT touch screens.

Specification:

Item Type: Motherboard

Motherboard Model: For MKS SGen-L Mounting

Hole Size: Approx. 102 x 76mm / 4.0 x 3.0in

Microprocessor: 32-Bit Cortex M3 (LPC 1768/100Mhz)

Input Voltage: 12V~24V

Motor Driver: TMC2130/2208/2100, 4988/8825

Temperature Sensor Interface: NTC100K/PT100

Display: Support MKS TFT Series Screen and LCD Screen

Support for Print File Format: G-Code

Recommended Software: For Cura/Simplify3d/Pronterface/Repetier-Host

Firmware Update: TF Card Update

Support Machine Structure: For XYZ/Delta/Kossel/Ultimaker/Corexy

.w-e-text table td,.w-e-text table th,.wang-edit-text table td, .wang-edit-text table th{border: .5pt solid #000;};.w-e-text table,.wang-edit-text table{border: 1px solid #000 !important;}

Package List:

MKS SGEN L V1.0 x 1 USB Data Cable x 1 TMC2208 Silent Drive x 5 Heat Sink x 5 Screwdriver x 1

• TMC2208 single-axis stepper motor driver chip, power tube built-in drive current 1.4A, peak current 2A, voltage range 4.75V-36V, 256 subdivision.
• With patented for spreadCycle high chopping frequency, for dcStep/stallGuard2 locked-rotor detection technology, for coolStep current dynamic adjustment technology, can save 70% energy.
• StealthChop's quiet and flexible microPlyer interpolation unit provides up to 256 microsteps/step resolution, perfect for sinusoidal control even in systems with limited pulse rates.
• Since stealthChop fine-tuning technology is widely used in 3D printing, the design of these components is also compatible with existing 3D printer electronics, eliminating the costly cost of redesign.
• Both components have pulse/direction inputs for full autonomous operation. Configuration is achieved through digital input. It can replace the original TMC2100 with lower calorific value, which is especially suitable for the 3D printing market.Adopt 32-bit Cortex-M3 LPC 1768 master chip, 100MHZ frequency, strong computing power, performance greatly improved.

Product description

➤ Item Description:

      ✔ Bootloader installed (ISP/USB Arduino).

      ✔ TMC2208 drivers is super quiet.

➤ Features:

      ✔ With speicial power chip, support 24V power input

      ✔  The circuit board is optimized by circuit, effectively solve the heating problem

      ✔ Can work with E/Z/Y/X axis motor

      ✔ With USB interface, easy to operate

      ✔ Replacement board for Ender-3 220*220*250mm 3D Printer

      ✔ Compatible with Creality Ender 3, Ender 3 Pro, cr-10, Ender 5 3D printer. PLEASE NOTICE: It only preinstalls the Ender-3 firmware, if you want to install it in your Ender 3 Pro or Ender 5, need to flash the Ender 3 Pro / Ender-5 firmware.

      ✔ Driver: TMC2208 drivers. Marlin 1.1.8 and Bootloader installed,the firmware can be modified by ARDUNO with USB cable.

      ✔ Thermal runaway protection is enabled. The Board is Optimized by Circuit, effectively solve the Heating Problem.

➤ Specifications:

      ✔ Voltage: Takes 24V input voltage

➤ Package Included:

      ✔ 1x Ender-3 Silent Mainboard(V1.14)

• ✔✔ Thermal runaway protection is enabled. The Board is Optimized by Circuit, effectively solve the Heating Problem.
• ✔✔ The circuit board is optimized by circuit, to effectively solve the heating problem --- Can work with E / Z / Y / X axis motor.
• ✔✔ Spare board for Ender-3 220 * 220 * 250mm 3D printer. Compatible with the Creality Ender 3 3D printers.
• ✔✔ Driver: TMC2208 driver. Marlin 1.1.8 and bootloader installed, the firmware can be changed by ARDUNO via USB cable.
• ✔✔ With USB interface, easy to operate.

• 【 Creality Ender 5 Pro 3D Printer 】With three upgrade Features, V1.1.5 Silent Mainboard, Metal Extruder Frame, Premium PTFE Tube. Solid cube frame and Semi-assembled kits easy to install, it ensures a better printing quality.
• 【 V1.1.5 Silent Mainboard 】Ender 5 Pro Upgrade Motherboard CV1.1.5 Silent Mainboard with TMC2208 Driver, Marlin 1.1.8 and Bootloader installed, Thermal runaway protection is enabled.
• 【 Metal Extruder Frame 】The metal extruder have better stronger pressure to pushing filament into printer nozzle, and longer lasting heat, will not clogged the Extruder.
• 【 Premium PTFE Tube 】Upgrade Capricorn Bowden PTFE Tubing, High Temperature Resistance-Heat, good flexibility, abrasion resistance, chemical resistance, to better improve the printer's performance.
• 【After-sales Services】With 1 year warranty, good customer service, if you have any question , please feel free to contact us, we will reply to you as soon as possible.

User questions & answers

Question:	Does this printer have a 4.3inch touch screen
Answer:	I think this happened to me too. Make sure you are using the logic ground and not the motor ground.
Question:	This printer's hot bed can't reach 100 degrees. Is that normal
Answer:	DRV8825
Question:	Which filaments does it work with
Answer:	It's 4.2.2
Question:	What size of filament is recommended for this printer
Answer:	All Creality BLTOUCH can works for this printer, but pay attention to the mouting brackets which is not same as ender 3 mount brackets.

Product features

Why Choose Our Printer ?

• 1, Our printer was produced by Creality 3D, quality was very good .
• 2, We provide good after sale service, if you have any question , please feel free to let us know, we will reply to you as soon as possible.

Ultra-mute Motherboard

• Upgraded motherboard which produces less noises, it uses creality 3D 4-layer PCB with solid filter and capacitor for better ESD protection and more stable performance TMC ultra-quiet drive 256 subdivision for finer printing.

Metal Extruding Unit

• We creatively use metal extruding unit, which is stable in feeding in filaments and wear-resisting , longer lasting heat, will not clogged the extruder, We get better printing quality.

Imported Blue Teflon Tube

• Capricorn Premium PTFE Bowden Tubing, High Temperature Resistance-Heat, good flexibility, abrasion resistance, chemical resistance, to better improve the printer's performance.

Double Y-Axis Design

• Ender 5 Pro has a double y-Axis control system with synchronous operation and stable output to avoid vibrations resulting from long-time printing.

High-standard V-solt Profile

• Ender 5 pro employs V-slot profile and pulley for stable and smooth operation, low noise, wear-resistant and a longer service life.

Removable Platform

Ender 5 Pro rolled DIY machine model and whole machine working into one with enhanced stability. A single machine, two different experiences.

Modular Design DIY Fun

• Ende 5 Pro has modular parts to assemble by yourself to meet the assembly requirements of enthusiasts like you.

Applications

Buyers Show

There are many reasons if you can not get a perfect printing model, like the temperature setting or hot bed leveling. But we are always here to help you solve the problem, in this situation, you can send us some pictures or videos to let us know. And we will try our best to solve for you, we are happy to help you.