10 best electric wire for outlet

Product description

For general wiring of homes, stores, and shops. Southwire Romex Brand SIMpull NM-B (nonmetallic-sheathed) cable may be used for both exposed and concealed work in normally dry locations at temperatures not to exceed 90°C (with ampacity limited to that for 60°C conductors) as specified in the 2011 National Electrical Code. NM-B cable is primarily used in residential wiring as branch circuits for outlets, switches, and other loads. NM-B cable may be run in air voids of masonry block or tile walls where such walls are not wet or damp locations. Voltage rating for NM-B cable is 600 volts.

• Coated in patented SIMpull Cable Jacket for easier pulling, stripping, and installation
• Primarily used in residential wiring as branch circuits for outlets, switches, and other loads
• UL Listed type NM-B
• 14 gauge, 2 conductors with ground, 25' per coil
• Made in America

User questions & answers

Question:	what is different than
Answer:	We just turned it on and left it. Worked the summer. Auto ON and off
Question:	I want to use this to pull an existing indoor outlet to create an outdoor outlet to a covered protected patio.Is this ok as long as it never gets wet
Answer:	It's under the top of the solar panel-- small bulb. We love this lantern. It's beautiful when lit up. We use it on the ground though or hanging.
Question:	Since thinner gauge is more flexible and easier to pull & re-run, would 2x 14- 2 replace 1x 12-2 gauge
Answer:	you can leave them outdoors and they will still wotk, Beautiful pattern and waterproof to boot.
Question:	Can i use this as replacement wire for the datacomm 50-3323-wh-kit as sold on amazon
Answer:	The product is metal 8.8 inch with the handle, 3.4 inches wide

Product features

Southwire’s Wire and Cable: A Constant Innovator For Your Installation Needs

Southwire continues to innovate to bring solutions to the electrical industry as one of the leading manufactures of wire and cable. With nearly 70 years of experience, our wire and cable products are designed to help simplify installation, reduce labor and material costs, while assisting to create a safer work environment.

Product description

Leviton T5320-W straight blade tamper resistant duplex receptacle, 125 V, 15 A, 2 pole, 3 wire, 1 pack, white.

From the Manufacturer

Leviton's duplex receptacles are designed for a chic appearance, quick installation and durability. The impact-resistant thermoplastic design allows for a long service life and high performance in homes, offices, schools and other settings. 15 Amp, 125 Volt, Tamper Resistant, Duplex Receptacle, Residential Grade, Grounding, White.

• Shutter mechanism inside the receptacle blocks access to the contacts unless a two-prong plug is inserted, helping ensure hairpins, keys, etc., will be locked out
• TR symbol on residential receptacles assures they meet the 2008 NEC requirement
• Ultrasonic heavy-duty construction offers long, trouble-free service life
• Heavy-gauge, rust-resistant steel mounting strap
• Shallow design for maximum wiring room
• Wallplate sold separately

User questions & answers

Question:	Can I replace a two prong outlet with this one
Answer:	Yes. I replaced three two pronged outlets with three of these in my home and they work perfectly.
Question:	Should these be used with outlet covers or without? We have a home with standard receptacles and plastic covers that go into the slots now
Answer:	Covers are not needed with this outlet. As stated in the product description:Shutter mechanism inside the receptacle blocks access to the contacts unless a two-prong plug is inserted, helping ensure hairpins, keys, etc., will be locked out
Question:	Are these for copper wire only? Or both copper and aluminium
Answer:	14 AWG solid copper, 12 AWG solid copper or copper clad
Question:	My first time buying outlets, if I get these will I need to know anything about the ones I'm replacing or are these sort-of universal
Answer:	Standard home outlets are 15AMP, the only time you’d really need a 20AMP outlet is if your home is equipped to handle heavy duty construction equipment. Best way to confirm if your home can handle a 20 AMP fuse is to check your circuit breaker and it should say it on there.

Product features

Leviton T5320-W Straight Blade Tamper Resistant Duplex Receptacle

Leviton's duplex receptacles are designed for a chic appearance, quick installation and durability. The impact-resistant thermoplastic design allows for a long service life and high performance in homes, offices, schools and other settings.

Amperage: 15 A, Blade Type: Straight Blade, Color: White, Device Type: Duplex Receptacle, Feature: Tamper-Resistant, Grounding: Grounding, NEMA: 5-15R, Pole: 2, Termination: Quickwire Push-In & Side.

Product description

For general wiring of homes, stores, and shops. Southwire Romex Brand SIMpull NM-B (nonmetallic-sheathed) cable may be used for both exposed and concealed work in normally dry locations at temperatures not to exceed 90°C (with ampacity limited to that for 60°C conductors) as specified in the 2011 National Electrical Code. NM-B cable is primarily used in residential wiring as branch circuits for outlets, switches, and other loads. NM-B cable may be run in air voids of masonry block or tile walls where such walls are not wet or damp locations. Voltage rating for NM-B cable is 600 volts.

• Coated in patented SIMpull Cable Jacket for easier pulling, stripping, and installation
• Primarily used in residential wiring as branch circuits for outlets, switches, and other loads
• UL Listed type NM-B
• 12 gauge, 2 conductors with ground, 25' per coil
• Made in America

User questions & answers

Question:	would this work to run a plug for a 8ooo btu air cond
Answer:	wire gauge size
Question:	Will this wire pull through a 1/2 inch PVC conduit
Answer:	I'm not an electrician nor do I know code in your area so my opinion has little value. In general, you can pull this to an outside wall and use an outdoor covered gfci outlet on 15 amp circuit or covered gfci sockets (hinge covers). If it is covered patio and you are asking about running this wire exposed to the elements, the wire would be fine BUT, technically you cannot according to code because the ground wire inside the jacket is not coated like the hot and neutral are. If it were exposed to some sort of liquid spill, splash or otherwise it could harm the connection. The other reason is that since it is not protected in a wall, it is exposed to things hitting it, scuffing it, possibly nicking the jacket and into the wire. I suppose you could run you wire out of harms way and mount your gfci outlets higher for less chances of harm to them. Bottom line in a covered situation that does not get wet, the main threat is accidental human damage.
Question:	Im running a 30a hook up for my camper this will work right
Answer:	How much current will you be drawing on the circuit? 14 gauge wire carries 5 amps less than 12 gauge wire. Ampacity is the maximum current that a conductor can carry continuously under the conditions of use without exceeding its temperature rating. Current is measured in amperes or “amps”. You must use the correct size wire for the current (load) requirement of the circuit to prevent the wire from overheating.
Question:	Can I use this wire with a 40amp 240v breaker for a 240v 2000w wallheater
Answer:	No

Product features

Southwire’s Wire and Cable: A Constant Innovator For Your Installation Needs

Southwire continues to innovate to bring solutions to the electrical industry as one of the leading manufactures of wire and cable. With nearly 70 years of experience, our wire and cable products are designed to help simplify installation, reduce labor and material costs, while assisting to create a safer work environment.

Product description

Safety is the number one priority on any job site. Sperry Instrument's testing equipment can be put to good use ensuring that electrical equipment is properly installed and safe to operate. The condition of electrical installations can be established when contractors use test equipment. Any test unit that can be used to measure or review an application without coming in contact with a live conductor is a necessity. Testing equipment can be put to good use ensuring that electrical equipment is properly installed and safe to operate. Faulty installations can be lethal; the condition of electrical installations can be established when contractors use test equipment. Sperry Instrument is pleased to offer an innovative full feature line of test equipment designed to make electrical work faster and safer. The electrical testers below accurately identify and capture circuit continuity and voltage measurements. These testers are ideal for any electrical professional or to have at home.

From the Manufacturer

Non contact sensing circuit.

• VERIFIES VOLTAGE PRESENSE: Verifies the presence of AC Voltage prior to working on electrical installation or troubleshooting (GFI6302 and VD6504)
• DURABLE: Hi-Impact Resistant ABS housing with soft over-molded rubber grips with a compact ergonomic design (GFI6302 and VD6504)
• QUICKLY READ: Bright color-coded neon lights for easy visual indication (GFI6302)
• CIRCUIT SENSING: Non-Contact sensitivity detects 50-1000V AC and patented battery self-test feature (VD6504)
• AUDIBLE AND VISIBLE INDICATOR: 360° visual and beeping audio Non-Contact Voltage Detection (VD6504)
• RATED: CAT Rating III 300V, C-UL US (GFI6302), CAT Rating III 1000V, IV 600V, (VD6504) 10 ft Drop and 250 lb Crush (GFI6302 and VD6504)

User questions & answers

Question:	The volt sensor is so sensitive it goes off near an outlet. Is that normal? I thought I could stick it in the slots to find out which side was hot
Answer:	Yes, you can insert the tip of this tool into the slots of an outlet then press the button and it will tell you which side is hot. You can also use it to test the wires in a circuit if you are unsure which is the hot lead. If the wires are connected to the switch, outlet etc touch the tip to the bared wire at the contact point and it will tell you if it is hot. You can also just touch the insulation covering the wires to get a reading too. Try to keep the wires you are testing separted by a few inches if possible, this will help prevent any false reading you might get by voltage seepage from the insulated hot lead. If you didn't know - the hot wire in a circuit is usually black, red or maybe some other dark color, the white is the neutral or return and the green is the ground. Start by testing the dark wire first but as a precaution be sure the check the white also - someone may have wired in incorrectly and that could be a hot lead. I've had - well had, until I left it someplace - one of these for years and it's a good useful tool. So I gotta get another one now, and I'm getting one of these.
Question:	Can this be used as a circuit breaker finder
Answer:	You could use them to find a circuit breaker, if you had someone to watch the tester, while you went through your panel turning off and on your breakers untill you found the one that controlled that circuit. If you didn't want to do that then you will need to buy an circuit breaker finder kit.
Question:	does this tester work on low-voltage landscape lighting wires
Answer:	The non contact voltage tester will.
Question:	can it tell the diffrence between 220v and 110v
Answer:	If you can’t tell the difference 110v and 220v .You Dont Need A Meter.

Product features

Non-Contact Voltage Tester

This unit allows the user to verify the presence of AC voltage prior to working on an electrical installation or during troubleshooting without requiring physical contact with live electrical conductors. The fully insulated probe tip eliminates the risk of contacting live electrical wires while the patented battery check feature designed into the unit ensures tester and batteries are operating properly, virtually eliminating false negative readings.

Sperry Instruments GFCI Outlet Tester

When you need a GFCI Outlet tester that's compact, provides comfort for repeated use and tests seven different wiring conditions with a press of a button, reach for the Sperry GFI6302.

Product description

The Leviton line of residential plugs and connectors has been expanded with the addition of a grounding model available in four colors: Black, Gray, Orange and White and our best-selling 515PV and CV in Orange. Leviton Plugs and Connectors are rugged, easy to wire and feature brass plug blades and connector contacts for maximum conductivity.

• Ideal for replacement of plugs on tools, appliances and extension cords
• Hinged design provides fast, easy assembly
• Rugged PVC plug and connector resists moisture and chemicals
• Built-in cord grip adjusts automatically for use with 18-12 AWG.
• Total Power Outlets: 1

User questions & answers

Question:	Why does this product title include "Not Available" in its title when it shows as fully available below? Please do not post titles such as this
Answer:	The actual cord is exactly 34”, then when you add the length of the elongated plug, it just over 3ft. Looks neat and clean. I love it.
Question:	Can this be used outdoors
Answer:	yes
Question:	Where do you route the green wire? Does it run right up along the outside of the white piece? Looks like a tight fit between the case screw and wht pc
Answer:	Not yet. Just White.
Question:	need 1 for a 10/3 gauge wire
Answer:	Not sure why they sat and his. I am using mine on a horizontal. M aybe because they are worried about tg wire being bent...not sure but it's working fine
Question:	Is the 3' really 3 feet long, meaning 36", or is it actually less? i've found this is the case with some extension cords
Answer:	If its 110 volt yes, if it is 220 volt you will need 12/3. As long as it doesn't draw more than 20 amps, I would think an 8000 but air conditioner word be 110 volt and draw less than 20 amps.
Question:	Can this be used with gfci outlet
Answer:	Look at your local code. We are not allowed to pull romex through any conduit in our county
Question:	Does this come in black
Answer:	12 gauge is 20 amp cable. If you are desiring a 30 amp circuit you require 10 gauge as a minimum. There are a lot of great books for a low price on wiring available that cover these matters in detail for the average person with no electrical training. You might look around for the Black and Decker text used for cheap. Just remember that for a camper you will be looking at the rough weather and exterior methods and material as well.
Question:	why can not use on horizontal plugs
Answer:	Yes, it is possible to carry a 2000w 240V load on a 12/2 NM-B cable like this one. No, it will not pass an electrical inspection. The breaker must protect the wire, and if someone comes along and adds load to your heater circuit they could easily overheat the 12/2 and the 40A breaker would just let it fry as long as it never pulls 40 amps. Neither #12 nor #10 is good for 40 amps - both would overhead on a 35A load. You can drop down the breaker to a 240V 20A circuit breaker and both the cable and the load would be protected. It still would not pass inspection because of the improper color coding of this 12/2 cable. If the next owner of your home calls an electrician to rewire the house, he will think that your wall heater is 120V because standard household color coding is : black = +120 volts (Bus A) white = 0 volts (neutral wire) red =-120V bare = equipment ground (no current flow in during normal operation) That is why people are advising you to use 12/3 or 14/3 cable - 3-conductor Romex-type cables have a red jacketed wire in the bundle which is the proper color to use alongside the black cable for the two "hot" wires in a 240-volt circuit. This NM-B cable has an insulation rating of 600V, so it can tolerate 240V operation. I have used 12/2 to feed a 240V circuit - I fed the cable from a 240V 20A circuit breaker and used a red felt-tip permanent marker to color the white wire. This still would not pass an electrical inspection but it addresses the safety issues associated with serving your heater with 12/2 cable as long as the wire remains dry. I don't know the National Electrical Code well enough to say whether or not a black electrical tape on the white wire would pass an electrical inspection - that is also a obvious signal that the white wire is not a neutral wire. The calculations of 8.3 amperes drawn by your 2000-watt heater are correct. Using a 15A 240V breaker instead of 20A would introduce no further safety issues. Please do not use 12/2 to serve this load unless you mark the circuit as 240V in a can't-miss-it fashion, or the next person who tries to work on your wiring may assume that the white wire had 0 volts on it when it actually has 240 volts relative to the black wire - you may forget about it yourself and hurt yourself or your property sometime in the future. Misidentified wire is a cruel wiring mistake to leave behind. Happy wiring!

Product features

Sleek Socket Ultra-Thin Electrical Outlet Cover with 3 Outlet Power Strip and Cord Management Kit, 3-Foot

With the space saving 3 foot version sleek socket, less is more. Less clutter. Less hazards. Less obstacles.

The sleek socket is a home decor product that completely hides ugly, unsafe and bulky plugs and cords via a unique ultra-thin design that's about the thickness of a pencil on top of an outlet. Up to 90% thinner than traditional plugs, the sleek socket is thinner than the average baseboard.

The sleek socket drastically reduces, and in some cases completely eliminates obstructions between furniture and traditional plugs attached to an outlet. Now move furniture flush against the wall!

Every sleek socket includes an adhesive cord management kit of neatly and firmly secure the cord to the wall. The included one inch adhesive cord clips adhere to your wall for a snug fit.

LESS Clutter

LESS Obstacles

LESS Hazards

More Small Space Room

A small change, yet BIG impact.

The elegant design of the patented sleek socket enhances home decor and provides unmatched aesthetics around the outlet by eliminating ugly plugs and cords that clash with the color of the wall around the outlet.

Leviton 3W102-E Not Available Clamptite Hinged Straight Blade Cord Connector

The Leviton line of residential plugs and connectors has been expanded with the addition of a grounding model available in four colors: Black, Gray, Orange and White and our 515PV and CV in Orange. Leviton Plugs and Connectors are rugged, easy to wire and feature brass plug blades and connector contacts for maximum conductivity.

• ✅【High Quality】 High-impact resistant thermoplastic face and back body eliminate cracks, breaks and callbacks, create a finger-safe application before, during and after installation, and offer long, trouble-free service life.
• ✅【Universal Application】 These outlets are suitable for installation in various locations from home offices, business buildings, public areas, and more where only require a 15 Amp outlet.
• ✅【Easy Installation】 Designed for quick push-in wire and side wire. Break-off plaster ears for best flush alignment. Break-off tabs allow easy two-circuit conversion. Shallow dimensions allow for maximum wiring space in the junction box with other outlets and switches.
• ✅【UL & CUL LISTED】 Designed and tested in accordance with UL498 requirements.
• ✅【Self-Grounding】 A green grounding screw and self-grounding clip provide for automatic grounding in the junction box, protecting you from electrical shock.

Product features

ELEGRP Standard Decorative Receptacle

Perfect Decor Anywhere

Ideal for areas, such as homes, offices, business buildings, airports, schools, public restrooms, hospitals, and hotels.

All-Thermoplastic Body

Thermoplastic Face and Back Body, Fade Resistant

750℃ Flame Resistant, High-impact Resistant

Self-Grounding and Break-off Plaster Ears

•Green Grounding Screw

•High Impact Resistant Thermoplastic Material

•Self-grounding Clip

•Break-off Plaster Ears

Product description

The RT250 is an electrical receptacle tester that tests the wiring conditions at an electrical outlet and inspects GFCI devices. The LCD displays the voltage, identifies the wiring fault, and the time required to trip a GFCI device. It is designated for use with North American 3-wire 120V electrical outlets. GFCI electrical circuit tester inspects GFCI devices. Large LCD display shows voltage, wire faults, and GFCI trip time. Identifies common wiring faults on North American 120V outlets. Bright green and red LEDs illuminate for visual indicators. CAT II 135V safety rating. Durable 6.6-Foot (2 m) drop protection. For use on 3-wire, North American 120V electrical outlets only. For more than 160 years, Klein Tools has manufactured premium-quality, professional-grade hand tools that deliver the performance, durability and precision needed to get the job done right. Our family of engineers, workers and craftsman continue to put six generations of expertise into every tool we create by using only the highest quality materials, superior workmanship, and keeping manufacturing as close to home as we can. Klein isn't just the name of our company, it's also our family name. And since we're an American company that's family-owned and family-run, you know you can count on us to be here tomorrow. Klein Tools doesn't just make great products, we make great products that stand up to the demands of the professionals who use them every day ... Since 1857.

• GFCI RECEPTACLE TESTER FEATURES LARGE LCD READOUT. View results instantly without the need to look at a chart to understand results. In addition to a clear LCD readout, bright green and red LEDs illuminate to show correct or faulty wiring
• TEST TRIP TIME OF GFCI IN SECONDS. Find out if the trip breaker is functioning and how long it takes to trip
• DETECT AND IDENTIFY COMMON WIRING FAULTS. Conditions are Wired Correctly, Open Ground, Open Neutral, Open Hot, Dual Open (Neutral & Ground), Reversed Hot/Ground, and Reversed Hot/Neutral. The Dual Open condition is patent pending
• AUTO-HOLD FUNCTION IS CONVENIENT FOR HARD-TO-REACH OUTLETS. Simply remove tester to view the reading
• SAFE AND DURABLE TESTER FOR INSPECTIONS IN NORTH AMERICAN 120V OUTLETS. CAT II 135V safety rating and 6.6-foot (2 m) drop protection

• TAMPER RESISTANT - design prevents children from inserting hairpins, keys or other unwanted objects into the electric socket, keeping your home and loved ones safe.
• FITS MOST ELECTRICAL BOXES - These self grounding receptacle outlets employ a compact design measuring 1 3/8 x 4/1/8 x 1", contains breakable plaster ears for easy installation.
• EXTRA DURABLE - Made with strong heat resistant polycarbonate thermo-plastic body, this residential grade receptacle outlet with wall plate is built to last!
• UL LISTED, 15 Amp, 125 Volt, 3 Wire, 2 Pole. Self Grounding. VETERAN OWNED.
• LIFETIME REPLACEMENT WARRANTY - Iron Forge Cable stands behind all of its products 100%. If anything ever goes wrong with this outlet, we will replace it with a new one.

User questions & answers

Question:

Do these have the plate under the side screws, or do they require wrapping the wire around the screw

Answer:

THIS PLUG WILL WORK WITH A MAXIMUM OF 14 GAUGE WIRE -- THE CORD CLAMP & COVER WILL NOT CLOSE COMPLETELY WHEN USING ANYTHING LARGER THAN 14/3 SJT/SJO (14-gauge/3-conductor) CORDS/CABLES. The largest cord I could safely use with this Leviton Plug was a 14/3 SJTW cord & had to firmly close the cover with one hand while tightening the screw. If you need to replace the plug on a 12/3 12-gauge or 10/3 10-gauge electrical cord - I *highly recommend* using one of the larger, round Leviton plugs w/ the cord clamp that tightens independently from the plug housing. -- Those plugs will handle Cords up to 0.590" Diameter. -- Anything Larger than 0.590" Diameter, and you will be forced to use the Leviton Industrial "Black & White" Plugs, which feature an insert in the cord clamp/strain relief -- you can remove the insert to allow for use of larger cords up to 3/4" (0.750") in Diameter. Thank You All & Please Be Safe When Working With Electricity❗⚡🔌⚡

Product features

Iron Forge Cable Electrical Wall Outlets

Our residential grade outlets are built safe, easy to install, and are a go-to item for inside homes.

They match any decor and look great in kitchens, living rooms, bathrooms, and offices.

Compact Design

The compact design fits most electrical boxes, so you can rest assured they will work in any room in your house.

Made Durable

Made with strong polycarbonate and a durable design, our receptacle outlets and light switches are built to last.

UL Listed and Veteran Owned

15 Amps

125-127 Volts

3-Wire

Single and 3-Way Pole Options

Residential Grade

Heat Resistant

• 【15 Amp Flanged Inlet】: No oxidation for the Nickel coated copper pole on the plug, made of premium copper and Nylon plastic to avoid the damage of UV degradation and chemicals, rugged and durable for indoor and outdoor.
• 【Easy Reliable Installation】: 2" Hole size required, 4 long Stainless Steel screws will fix straight blade flanged inlet on the hole or wall more tightly. No gap on the edge!
• 【 Weatherproof Cover】: ETL approved, and the rv electrical outlet cap and back cover will protect it from the rain storm, snows, dust and even works well in Western Colorado winters, without crack and leak.
• 【No Need to Wire Up】 : The male receptacle is already wired up by 2 x 14AWG 18 inch extension cable with NEMA5-15R. Just plug in to connect the power.
• 【Widely Compatible】: As a generator or battery charger plug to energize your electrical devices. Widely used in trailer, camper, RV, car, boat, marine, block heater,home, bumper, recessed outlet box, etc

User questions & answers

Question:	Drill size for screws
Answer:	Yes, yes. It's right there in the very first line of the items name (in the Larger fonts) - "Leviton 3W102-E Not Available....". I need one - will order and see!
Question:	Do yousell this item with 3 plugs
Answer:	I would not recomend outdoor use. There is no seal water would easily enter and short or corrode the internal contacts. I suppose one could fill the thing with liquid electrical tape, as its called. But thatcis not its constructed purpose.
Question:	The description and photo show "thread body design for hole tightened" .... does this mean that there is a threaded plastic nut that is included
Answer:	I just went straight up and over, and then just work the screw between the wires when you go to close up the plug

Product features

WELLUCK 15Amp 250V AC Port Plug

• Waterproof ,Dust Proof and UV Proof
• Anti-Oxidation Copper Pole
• 4 Screws Holes Fixing System (No Gap Between Wall and Flange Edge)
• Wired Up Already
• Thread Body Design For Hole Tightened

Easy Installation

Plug-N-Play

Directly plug in. No hand wiring or cable modification required.

Dual Extension Cords

Y splitter adds extra length to your current electronic device cords.

Heavy Duty AC Port Plug

Self-Tapping

Simply flush mount with 4 screws

More Durable

Nickel Coated Copper. Anti Oxidation

Snap-fit Cap

Keeps out rain,snow and ice

Package Include

1* Flanged Inlet Receptacle with extension NEMA 5-15R Y splitter cord (15 Amp 125V NEMA 5-15 Inlet )

4* 1.02" Multi Purpose Stainless Steel Screws

1* Silicone Waterproof Cap

1* PP Back Cover

1* Hand Book

• 【Large Compatibility】This power strip surge protector tower( rated current 13A) is designed with adaptable voltages: 110V-240V. It will automatically adapt to the wall out voltage it is plugged in. Used in the United States (110-125V), its max power is 125V x 13A = 1625W.(Calculation Formula: P=UI.) This vertical power strip tower with large compatibility, max wattage up to 3000W, will absolutely meet your needs!
• 【Upgraded Design USB Port】Our tower power strip outlet has a double layer USB port special design. 0-2.1A/port, 4.2A in total. With smart IC technology, the USB slots are able to detect the plugged devices and automatically provide them the fastest possible yet safe charging current within the output capability. This USB power bar can charge 4 iPhones, or 2 iPhones+1 iPad plus, or 2 iPads at a time! (iPhone: 5V 1A; iPad: 5V 2.1A)
• 【All-Round Protection Technology】 With a built-in 900J surge protector, this USB multi-outlet strip will filter the minor surges in the circuit and shut it off when an overwhelming surge like that caused by lightning occurs. The overload/short-circuit protector at the bottom of the tower base will pop up to cut off power when it overloads or shorts. Unplug all devices and press them down to reset the power strip tower.
• 【Space Saving and Cord Retractable】 The innovative tower shape utilizes the vertical space and allocates the outlets evenly on four sides with them wide-spaced, which is perfect even for large and bulky power plugs and adapters. Another space-saving design is the retractable 6.5ft cord in the tower base, with which you can pull out the needed length and leave the rest inside for better balance.
• 【Energy Saving】This wire adjustable USB power strip surge tower has a portable handle, energy-saving independent switches, overload warning LED indicators.

Product features

Surge Protector Tower

There is an internal surge protector plus power switches on this electrical socket tower, which will automatically off if there is a surge (/lightning). Also off when it's overloaded, over-current, or over-heated. Later, you need to press the switch and reset it.

（But we should have safety awareness, we ought to unplug the appliances whenever a surge/lightning appears since nobody can predict how strong lightning will be, and all the surge protector is throwaway just like the fuse.）

The Number of Devices Can Be Charged:

(With 2.1A max per port, 4.2A total)

A: 4 iPhones

B: 2 iPhones+1 iPad

C: 2 iPads (iPhone: 5V 1A, iPad: 5V 2.1A.)

Power Tower by Other Brands

(Most are 2.1A max per port, 2.1A in total)

A: 2 iPhones

B: 1 iPad

Check and you will find most of their USB ports are in vain.

1382℉ Fire-retardent

This USB charging station is made of ABS+PC fireproof material, UL94 V-0, the highest level fire-retardant material, it's very safe and value for money.

In addition, it utilized a high-quality copper sheet with an integrated structure that the tight plug can be plugged in for about 10,000 times without becoming loose or falling out to better prevent from causing sparks and/or a fire.

A Hidden Overload Protection Button at the Bottom Is Great Help!

For better protecting you and your home, there is a Hidden Overload Protection designed at the bottom, which is safe with no high pitched sounds. When this 10-outlet power strip is overloaded, it will automatically power-off, so that your expensive devices will not be damaged. After that, you just need to re-set it, the power strip will instantly turn on again!

Retractable Cable Hide at the Bottom

The over 6ft extension cord can be hidden at the bottom of this vertical power strip so that you can better organize the mess extra cable of this standing power strip tower to have a well-ordered room! Thus you will never be annoyed by the messy wires which will sometimes suddenly trip you up to make everything a mess!

LED Indicator & Power Switch on Each Layer

The high security LED indicator will flash to warn you if the power strip is close to being overloaded. So that you can reduce the use of the devices over time, and prevent your devices from damage, which ensures safety for you! In addition, you can turn off the independent switch on each layer for energy saving when not in use.