12 best fulton trailer jacks

Product description

Fulton XP10 0101 Trailer Jack is designed for use with marine and utility trailers. Fulton brand tongue jacks are time-tested and application-proven. Features Z-MAX 600 Superior Plating corrosion protection. Bolt-on, includes all necessary mounting hardware and 1/2" pull pin. Sturdy 6" Poly wheel. The Fulton brand bolt-thru swivel mount uses 3-D formed heavy-gauge steel stampings and a proprietary bushing material for a mount with minimal deflection and maximum support. Mount fits up to a 3" x 5" trailer frame. Capacity: 1200 lbs., Travel: 10", Retracted Length: 12.5", Extended Length: 22.5" (Measured Center of Mount to Bottom of Wheel) Top Clearance: 10.5" (Measured Center of Mount to Top of Jack) 5 Year Limited Warranty.

• Bolt-On Swivel Tongue Jack, 1200 lbs. capacity
• Bolt-Thru mount with minimal deflection and maximum support
• Sturdy 6" Poly wheel, 1/2" swivel pull pin
• Hardware included to mount up to a 3" x 5" trailer frame
• Z-MAX 600 superior plating corrosion protection

User questions & answers

Question:	when turning the trailer, does the wheel and yoke pivot independently of the shaft or does it and the shaft pivot as a unit
Answer:	This is the same as any swivel caster that you would find on a piece of furniture. Only the wheel and its housing turns. The only movement that the shaft does is up and down.
Question:	Where is this made
Answer:	I don't know. Their website is a bit vague on where they are located, but it appears to be in the US.I can tell you the jack is incredibly well made. I bought mine last August and have enjoyed it tremendously. I used to use a trailer dolly to move my 4 x 8 open trailer around until I got the Fulton jack. Now I just easily roll it around with the attached jack.I had installed the jack too close to my bumper and it contacted it during a turn, knocking off the black plastic cap on the top of the tube. Without it, rainwater would get into the gear area. So I called Fulton and told them what I had done (making sure they knew it was my fault) and they apologized for the problem and sent me 2 replacement caps for FREE. Talk about great customer support!So, where is it made? Don't really know. Is it WELL made? Absolutely! After of almost a year of use it still works flawlessly.
Question:	how much lift from bottom of tire to middle of frame bracket
Answer:	Min 12" Max 22"
Question:	is jack easy to crank up and down
Answer:	Yes, I have the jack on my utility trailer. It is easy to crank. It cranks up and down slowly but surely.

Product description

Fulton, the industry leader for high performance marine jacks, is proud to introduce a revolution in trailer jack engineering. The F2, designed for use with marine, recreational and utility trailers, continues the Fulton heritage of innovation rethinking every feature and challenging industry conventions. The result is a reengineered high quality product that will transform the industry. It's so strong and reliable that Fulton is backing it with an unprecedented. Limited lifetime warranty.

• Corrosion resistant coatings cover internal and external components - will hold up in harsh environments
• Ergonomic design - crank, release pin and integrated wheel wedge are made of strong, engineered plastic for a comfortable touch
• Twin track wheel design with 1600 pounds capacity, 10 inch screw travel, 8 inch mount travel
• Limited lifetime warranty

User questions & answers

Question:	I have a 2017 nitro z18 bass boat. is this the one that will fit my trailer
Answer:	I bought the single wheel model 1600 for my 18 ft bw dauntless. If your z18 means 18 ft then you should have no problem with the 1600 single wheel~
Question:	have they upgraded the cheap plastic wheels to rubber ones yet
Answer:	Not to my knowledge. Bought mine less than a year ago and plastic
Question:	how tall can the trailer get
Answer:	The overall height depends on the length of the trailer.
Question:	Does this item include mounting hardware
Answer:	Yes this is the best system on the market

Product features

Fulton F2 Trailer Jacks—Twin Track, Wide Track, Foot Plate Models

Fulton, the industry leader for high performance marine jacks, has introduced a revolution in trailer jack engineering. The F2 series, designed for use with marine, recreational, and utility trailers, continues the Fulton heritage of innovation, rethinking every feature, and challenging industry conventions. The result is reengineered, high-quality products that are transforming the industry. They’re so strong and reliable that Fulton is backing them with an unprecedented Limited Lifetime Warranty.

Twin Track Trailer Tongue Jack

Maintenance free. Designed to eliminate the need for lubrication and maintenance

Corrosion resistant coatings cover internal and external components that will hold up in harsh environments.

Ergonomic design: crank, release pin, and integrated wheel wedge are made of strong, engineered plastic for a comfortable touch.

Twin track wheel design with 1600 lb. capacity, 10-inch screw travel, 8-inch mount travel.

Sealed and lubricated one-piece gearbox.

Limited Lifetime Warranty.

Wide Track Trailer Tongue Jack

Corrosion resistant coatings cover internal and external components will hold up in harsh environments.

Ergonomic design: crank, release pin, and integrated wheel wedge are made of strong, engineered plastic for a comfortable touch.

Wide track wheel design with 1600 lb. capacity, 10-inch screw travel, 8-inch mount travel.

Sealed and lubricated one-piece gearbox.

Limited Lifetime Warranty.

Trailer Tongue Jack with Foot Plate

7-inch diameter heavy duty articulating footplate for superior stability.

Articulating ball and socket connection between jack and footplate accommodate uneven surfaces.

13-inch of swivel mount height adjustment.

Bolt-on version includes hardware for 4-inch and 5-inch frames.

Handle hold-Up secures handle to jack tube when in stowed position.

Limited Lifetime Warranty.

A-Frame Tongue Jack--requires F2 Coupler

Versatile handle orientation mounting options: front, driver side or passenger side.

Removable foot/wheel options (purchase separately): 7-inch round articulating footplate with 2,000 pounds lift capacity, 7-inch diameter twin track wheel with 1,600 pounds lift capacity, 8-inch diameter wide track wheel with 1,600 pounds lift capacity.

Limited Lifetime Warranty.

Product description

Designed for use with marine and utility trailers, Fulton brand XP tongue jacks are time-tested and application-proven. their bolt-on versions include all necessary mounting hardware. XP 15 mount features 1/2 inch pull pin. The Fulton brand XP bolt-thru swivel mounts (U.S. PAT. 6,302,381) use 3-D formed heavy-gauge steel stampings and a proprietary bushing material for a mount with minimal deflection and maximum support. Mounts have multiple mounting positions up to a 3 inch x 5 inch trailer frame. 8 inch diameter wheel, handle and wheel are shipped unassembled.

• Capacity: 1500 pounds
• Travel Distance Length: 10 inch, Retracted Length: 13 inch, Extended Length: 23 inch (measured from center of mounting plate, to bottom of wheel)
• Clearance: 12.4 inch (measured from center of mounting plate to top of jack)
• Z-MAX 600 Zinc finish to resist corrosion
• Limited 5 Year Warranty

User questions & answers

Question:	were are Fulton Product manufactured
Answer:	Thankyou for your inquiry. It's a pleasure to assist you. Fulton is manufactured by Cequent Performance Products. The XP15 jack is made in China.
Question:	what is the measurement of this jack from the bottom of the wheel to the bottom of the trailer when fully retracted
Answer:	Not sure why this is a relevant question as this is a swing-away jack. When you hook up to your tow vehicle just swing it and stow it so it is parallel to the trailer. But having said that an eyeball measurement is close to 11 1/2 inches.
Question:	I currently have a Fulton center bolt that needs replaced is the mounting standard
Answer:	Yes,mine was a center bolt also , this one has brackets that mount to the trailer not a center bolt. I would say this,my handle already broke so I’m in need of a new one, I would spend a little more money to get a better one next time.
Question:	Is this jack or the finish able to withstand salt water
Answer:	Nothing can really withstand salt water completely, but if you spray it down after trailering it should last a long time. Proper maintenance is crucial

Product description

Patent pending TruTurn 360 system delivers best in class castering performance. Raises and lowers 35 percent faster than the competition with 20 percent more screw travel than conventional jacks. Grease fittings in key locations for easy lubrication. Patented inner and outer tube bushings provide a tight fit and lessen tube drag and a Premium Sharkskin finish for optimum corrosion resistance. Features stylized handles with soft touch grips. 8 inch diameter spoked wheel, handle and wheel are shipped unassembled.

• Capacity: 1500 pounds
• Travel Distance Length: 12 inch
• Patent Pending TruTurn 360 Castering System
• XLT Premium Sharkskin finish for protection from salt water and salt spray elements
• Swing Away, Bolt-On (Mounting Hardware Included)

User questions & answers

Question:	Is the wheel all plastic or what is it
Answer:	Plastic, but larger diameter than the jack it replaced. I am happy with the jack overall. And the plastic wheel seems more than tough enough for my trailer situation.
Question:	Does it come with mounting hardware
Answer:	Yes it comes with all mounting you will need
Question:	Could someone please give me the dimensions of the bolt hole pattern ? Is it the same as the F2 version
Answer:	Yes
Question:	Does the wheel turn independently from the rest of the jack? The one I have now the wheel is attached to the inner shaft
Answer:	Yes, the wheel turns independently from the housing. It spins a full 360 deg. Great product!

Product description

Bolt-On design 5000 pounds capacity heavy duty square jack, includes drop leg with footplate for maximum 35 inch extended length and minimum 6.5 inch retracted length (measured from center of mounting plate). Mounting hardware for 4 inch, 5 inch and 6 inch frame Included. Z-MAX 600 Zinc finish to resist corrosion.

• Lift capacity 5000 pounds
• Drop leg design with a 6 inch x 8 inch footplate
• Mounting hardware for 4 inch, 5 inch and 6 inch trailer frame
• Travel: 28 inch (includes drop leg) Clearance: 18.5 inch (center of mounting plate to top of jack) Retracted: 6.5 inch Extended: 35 inch (center of mounting plate to bottom of footplate)
• Z-MAX 600 Zinc finish to resist corrosion

User questions & answers

Question:	Can the gears be lubricated periodically
Answer:	The gears are packed in a heavy duty grease from the manufacturer and normally are not in need of further greasing. But the top cap on the unit can be removed with some effort and grease could then be applied with a grease gun. Alternatively a hole could be drilled above the crank handle & a press in grease fitting could be installed. But as I mentioned the unit comes pre greased with a heavy duty grease and greasing is not normally needed.
Question:	Will the 5000 lb it fit a 3" by 5" trailer
Answer:	I purchased this Jack and have a center tongue rail that is 3x5” and it fits perfectly. I’ve had the jack for a couple years now and is still in good condition without any rusting.
Question:	Do they make a caster wheel I can put on instead of the flat foot
Answer:	No, not for this jack. A foot offers much higher capacity and better stabilization than a wheel would at that kind of weight ratio. Hope this helps. Bert CampRigid Hitch Amazon Sales
Question:	Whats the warranty on this item? I have mine for under 2 years and alrrady the crank broke
Answer:	There's a link in the product info block here on Amazon to the PDF warranty document. The warranty is for 5 years.

Product description

Fulton XPD15 0101 Trailer Jack is designed for use with marine and utility trailers. Fulton brand tongue jacks are time-tested and application-proven. Features Z-MAX 600 Superior Plating corrosion protection. Bolt-on, includes all necessary mounting hardware and 1/2" pull pin. Sturdy Dual 6" poly wheels. The Fulton brand bolt-thru swivel mount uses 3-D formed heavy-gauge steel stampings and a proprietary bushing material for a mount with minimal deflection and maximum support. Mount fits up to a 3" x 5" trailer frame. Capacity: 1500 lbs., Travel: 12", Retracted Length: 13", Extended Length: 25" (Measured Center of Mount to Bottom of Wheel) Top Clearance: 14.4" (Measured Center of Mount to Top of Jack) 5 Year Limited Warranty.

• Bolt-On Swivel Tongue Jack, 1500 lbs. capacity, with an additional 2" of travel
• Bolt-Thru mount with minimal deflection and maximum support
• 6" Dual Wheel, 1/2" swivel pull pin
• Hardware included to mount up to a 3" x 5" trailer frame
• Z-MAX 600 superior plating corrosion protection

User questions & answers

Question:	If this doesn't fit, can I return it
Answer:	Fit what? I mounts on 3 to 5 inch frames. To fit the 5 inch it is turned 90 degrees for mounting.
Question:	How good is the warranty? Mine just had the handle fall out on the way to the lake. Not acceptable
Answer:	had this happen to 3 of these jacks. The handle falls out and you are screwed........
Question:	what is the advantage or disadvantage of a trailer jack with dual (2) wheels
Answer:	It’s been an advantage for us. With a 24ft trailer, 19ft boat, 2900lbs. It’s been far easier handling the trailer to push into a tight garage opening. The single wheel originally on trailer would drag and was hard to pivot. Using a mallet to pivot the old single wheel was a pain, drag marks on drive.
Question:	How easily will this turn? What I mean is, with the wheel in straight alignment with the trailer tongue, how difficult to move the tongue sideways
Answer:	harder to turn with both wheels, a single wheel jack works better for turning.

Product description

Fulton TJ1200 Trailer Jack is designed for use with marine and utility trailers. Fulton brand tongue jacks are time-tested and application-proven. Features Z-MAX 600 Superior Plating corrosion protection. Bolt-on, includes all necessary mounting hardware and 3/8" pull pin. Sturdy 6" Poly wheel. The Fulton brand retaining ring swivel mount offers minimal deflection and maximum support. Mount fits up to a 3" x 5" trailer frame. Capacity: 1200 lbs., Travel: 10", Retracted Length: 12.7", Extended Length: 22.7" (Measured Center of Mount to Bottom of Wheel) Top Clearance: 11.4" (Measured Center of Mount to Top of Jack)

• Bolt-On Swivel Tongue Jack, 1200 lbs. capacity
• Sturdy 6" Poly wheel, 3/8" swivel pull pin
• Hardware included to mount up to a 3" x 5" trailer frame
• Z-MAX 600 superior plating corrosion protection
• Limited 5 Year Warranty

User questions & answers

Question:	What is the center to center distance of the horizontal holes on the mounting plate? I need 6" center to center or 5.5" between the inside edges of holes
Answer:	If you go on the website it gives you a template with the dimensions. As it happens, my trailer is two states away at this time and I can't measure for you.
Question:	Is this Jack assembled with the snap ring
Answer:	I suppose so......I've never had the occasion to take it apart.
Question:	How do I warranty it out after 12 months it has completely failed even after filling it with a tube of grease when brand new
Answer:	get in touch with the dealer, or anyone that sells the jack-----by the way, how did it fail??
Question:	Can yon provide a CAD model of this trailer jack
Answer:	No. That is proprietary information.

Product description

FULTON F2 MARINE AND RECREATIONAL JACKS1,600 lb. Wide TrackIncludes Handle Hold-Up & Wheel Wedge Features, & Bolt-On Mounting Hardware for 3" x 3" & 3" x 4" FramesFulton, the industry leader for high performance marine jacks, is proud to introduce a revolution in trailer jack engineering. The F2, designed for use with marine, recreational and utility trailers, continues that Fulton heritage of innovation rethinking every feature and challenging industry conventions. The result is a reengineered high quality product that will transform the industry. It's so strong and reliable that Fulton is backing it with an unprecedented LIMITED LIFETIME WARRANTY.Maintenance free - designed to eliminate the need for lubrication and maintenance.Corrosion resistant coatings cover internal and external components - will hold up in salt water and other harsh environments.Ergonomic design - crank, release pin and integrated wheel wedge are made of strong, engineered plastic for a comfortable touch.Stylish design - compliment your boat and customize your trailer's styling.Sealed and lubricated one-piece gearbox.LIMITED LIFETIME WARRANTY

• Boat Length - Max (Feet) NONE
• Boat Weight - Max (Lbs) NONE
• Pull Strength (lbs) NONE
• Vertical Lift (Pounds) NONE
• Gear Ratio NONE

Product description

Fulton XP15L 0101 Trailer Jack is designed for use with marine and utility trailers. Fulton brand tongue jacks are time-tested and application-proven. Features Z-MAX 600 Superior Plating corrosion protection. Bolt-on, includes all necessary mounting hardware and 1/2" pull pin. Sturdy 8" spoked wheel. The Fulton brand bolt-thru swivel mount uses 3-D formed heavy-gauge steel stampings and a proprietary bushing material for a mount with minimal deflection and maximum support. Mount fits up to a 3" x 5" trailer frame. Capacity: 1500 lbs., Travel: 12", Retracted Length: 13", Extended Length: 25" (Measured Center of Mount to Bottom of Wheel) Top Clearance: 14.4" (Measured Center of Mount to Top of Jack) 5 Year Limited Warranty.

• Bolt-On Swivel Tongue Jack, 1500 lbs. capacity, with an additional 2" of travel
• Bolt-Thru mount with minimal deflection and maximum support
• Sturdy 8" spoked wheel, 1/2" swivel pull pin ; Handle Style: Sidewind
• Hardware included to mount up to a 3" x 5" trailer frame. Pull Pin Diameter-0.5 inch
• Z-MAX 600 superior plating corrosion protection

User questions & answers

Question:	Does the caster rotate indepedently
Answer:	The wheel will swivel 360 degrees.
Question:	Newbie to trailer jacks...what is the benefit of 12” lift vs those with
Answer:	The height of the back end of the car or truck and the hitch you will be be using. The trailer will need to be jacked up above the hitch to disconnect. Also keep in mind uneven ground.
Question:	What material is the wheel made of? Is this jack sturdy enough to hold up on a two-horse trailer
Answer:	Hi Larry: The trailer I own weighs about 3200 pounds dry and this jack supports it well. Unsure about a two-horse trailer. I would suggest calling the manufacture with the total weight of your trailer and asking them if this jack is sturdy enough to support your trailer. I would hate to say yes and it wasn't able to work for you.Dan
Question:	How long is this jack in the retracted and extended positions (including wheel)? Thanks
Answer:	It's in the product description: Travel: 12", Retracted Length: 13", Extended Length: 25" (Measured Center of Mount to Bottom of Wheel) Top Clearance: 14.4"

Product description

Designed for use with marine and utility trailers, Fulton brand tongue jacks are time-tested and application-proven. Our bolt-on versions include all necessary mounting hardware. For weld-on versions include all necessary mounting hardware. For weld-on applications, we offer two styles of mounts for both 1/2" and 3/8" pull pin models. The Fulton brand bolt-thru swivel mounts (U.S. PAT. 6,302,381) use 3-D formed heavy-gauge steel stampings and a proprietary bushing material for a mount with minimal deflection and maximum support. All mounts fit up to a 3" x 5" trailer frame.

• Strong proprietary bushing materials
• Stable-formed heavy-gauge steel construction
• Weight Capacity: 1200 lbs.
• Travel: 10"
• 6" Poly wheels

User questions & answers

Question:	Does this Jack come with mounting hardware
Answer:	Mine did not. I used the hardware from the old one
Question:	What is the measurement from the bottom of the tongue to the bottom of the wheel when fully extended
Answer:	ZIEMAN TRAILER-A LITTLE OVER 22 INCHES
Question:	does this jack pivot up parallel with the tongue
Answer:	Yes
Question:	Does it have grease fitting
Answer:	Yes it has a grease fitting. Looks like a standard fitting for most grease guns.

Product description

Fulton XLT Jacks are loaded with premium features. This Trailer Jack is Powered through 7-way or dedicated common battery (with winch), or manual override using standard tools in case of power loss. The patented spring-loaded drop leg pull-pin design positions quickly with 22" total travel. SHARKSKIN Premium Finish is environmentally friendly and self-healing, provides maximum corrosion resistance, and is specially formulated for use in salt water environments and other demanding climate applications. Easy to install, simply bolt on to frame and hook up wiring. Includes mounting hardware for up to 5" high trailer tongues and backed by Fulton's 5 Year Limited Warranty. With more than 100 years of impeccable performance, the Fulton line of trailer jacks, winches, and couplers has become the industry standard for light and medium-duty trailering. Suited for all environments, Fulton performs best when the weather is at its worst. When innovative design is combined with quality and value, the result is a brand that is the obvious choice for recreational and marine applications everywhere.

• Features a patented spring-loaded drop leg pull-pin design that position quickly with 22 inch total travel
• Sharkskin premium finish for optimal corrosion resistance and corrosion resistant stainless steel internal ACME screw
• Manual override using standard tools in case of power loss
• Easy to install - simply bolt to frame and hook up wiring
• Includes mounting hardware for up to 5 inch high trailer tongues

User questions & answers

Question:	I’m assuming this has 2 wire DC that can be wired to a typical 4 wire plug most vehicles have
Answer:	Correct just a negative and positive.
Question:	what is the HP of the motor or What size in line fuse do you recommend
Answer:	30 amp fuse.
Question:	How is the 22" of total travel determined? Some say it has only 14" of travel. What makes up the additional length besides the 8" drop leg
Answer:	The leg has like 6 holes that you can drop or raise as needed for the extra travel. I have a 4x4 with a 6" lift and I have more than enough travel on the jack.
Question:	Are there instructions somewhere for powering via the 7-way connector on the tow vehicle? I can't seem to find them
Answer:	You cannot power by 5 or 7 pin do to ampdraw and to small gauge wire on truck. Technically you have to have external battery or run your own harness from vehicles battery to the rear location as dedicated power supply

Product description

Fulton XLT jacks are loaded with premium features. Each XLT jack features the patent pending TruTurn 360 system that delivers best in class castering performance. They raise and lower 35 percent faster than the competition and have 20 percent more screw travel than conventional jacks. Patented inner and outer tube bushings provide a tight fit and lessen tube drag. Grease fittings are located in key locations for easy lubrication. Ergonomic stylized handles, with soft-touch grips, offer greater comfort. Sharkskin premium finish is environmentally friendly and self-healing, provides maximum corrosion resistance, and is specially formulated for use in salt water environments and other demanding climate applications. Backed by Fulton's 5 year limited warranty. With more than 100 years of impeccable performance, the Fulton line of trailer jacks, winches, and couplers has become the industry standard for light and medium-duty trailering. Suited for All environments, Fulton performs best when the weather is at its worst. When innovative design is combined with quality and value, the result is a brand that is the obvious choice for recreational and marine applications everywhere.

• Patent pending TruTurn 360 system delivers best in class Castering performance; raises and lowers 35 percent faster than the competition; 20 percent more screw travel than conventional jacks
• Patented inner and outer tube bushings provide a tight fit and lessen tube drag; grease Fittings in key locations for easy lubrication; stylized handles with Soft-Touch grips for greater comfort
• Sharkskin finish is environmentally friendly and self-healing; provides maximum corrosion resistance; specially formulated for use in salt water environments and other demanding climate applications
• 1, 500 lb. Rating; fits trailer frames up to 3 inches x 5 inches; weighs 19 lbs., has 12 inches of travel, 14.5 inch Retracted length, 26.6 inch extended length, 15.9 inch ground clearance
• Requires Fulton p9012-00 weld-on mount & hardware kit (sold separately) for installation on trailer frame; backed by Fulton's 5 year limited warranty
• Fit type: Vehicle Specific

User questions & answers

Question:	Does the bracket weld on or bolt on
Answer:	I should have answered the weld on plate is welded to the trailer and has to be purchased separately I think, it has one bolt in the center that this jack attaches to...I replaced another Fulton so my bracket was already welded to the trailer.
Question:	What size wheel is this
Answer:	8 inch
Question:	I already have a weld on mount on my yamaha sx230 trailer, would this jack be the same as a bolt on if just using the center swivel bolt to install
Answer:	Depends upon the configuration of your mount? The P-9012 weld-on mount is NOT included with this jack. The measurements of the P-9012 is 4-1/2" wide X 4-1/2" tall with 3" bolt hole centers. It can be found here on Amazon. https://www.amazon.com/dp/B004RBVNC2?ref=myi_title_dp
Question:	Is there a way to get a replacement rubber top cap for this hitch
Answer:	you can find replacement at etrailer.com