14 best insulation materials

Product description

5/16" thick with two outer layers of aluminum foil. Each foil layer is bonded to a tough layer of polyethylene for strength. Reflects up to 97% of radiant heat with an R-value up to 14.3 depending on application. Excellent vapor barrier for below grade. Can be used for radiant floors, crawl spaces, duct insulation, metal buildings, basement walls & attics. Square edge roll double bubble foil both sides 5/16" thick with two outer layers of aluminum foil Each foil layer is bonded to a tough layer of polyethylene for strength Reflects up to 97% of radiant heat with an R-value up to 14.3 depending on application Excellent vapor barrier for below grade Can be used for radiant floors, crawl spaces, duct insulation, metal buildings, basement walls & attics. Easy applied with tape & staples. Specifications Size: 24" x 10'.

• Inhibits or eliminates condensation
• Nontoxic/no carcinogenic
• Does not require Protective clothing, goggles, or respirator

User questions & answers

Question:	Temperature rating
Answer:	According to the manufacturer's web site -60 to 180 Fahrenheit.
Question:	would this be good for a well house insulator? if not what would b good
Answer:	I would say no. This is for small things that don't need much insulation. I would say a board type insulation like Tyvec would be a better choice for a well house.
Question:	I want to make custom fit side window covers for may car. Do the edges need to be sealed/wrapped with tape to keep from ripping/fraying/etc
Answer:	I would say that is not necessary. The material is stromg and does not tear easily. However, I made tabs from blue 3M masking tape to make it easier to remove the Reflectix window cover from the windows. If you should happen to cut your cover a bit small making a tape edging solves that problem. Check out YouTube for some good ideas on using Reflectix for window coverings...lots of good pointers.
Question:	Would this help keep heat out if put on inside of windows (AZ
Answer:	You bet! That's what I did with it. I measured windows inside the van, cut the material out about 1/2-3/4" larger than the window size, top and bottom, then just push it into the window and smooth it into shape in the area. Trimmed little bits until it fits snugly. Then I wrote on each piece with marker pen to denote which window it goes in. You can easily take them out for driving, and then put them back when you are storing or parking in the sun. It covered the two back door and two side door and two overhead windows in overcab area. Would need larger size if you have more windows.

• The cost effective 80 mil automotive butyl and foil sound deadening! You are not just buying an excellent quality product but also saving more than 20% comparing to competitors as well!
• Now the material is 1,5 times thicker that will get you 1,5 times more effective insulation. Mat66 80 mil is 1,5 times better in comparison to sound deadening material of 50 mil. The thicker the material the more performance you get!
• Automotive self-adhesive insulation consists of butyl. Mat66 sound deadening mat has a total weight of 0.5 lbs/1sqft. This weight ensures maximum efficiency and sound insulation that could be possibly gained from 80 mil thickness material. Mat66 80 mil is light weighted sound deadening material!
• Car insulation Mat66 has a special indicator as to if it is installed correctly. The special embossing on the foil must be rolled out with a roller till it is plain smooth, then you'll be 100% sure that the soundproofing is set correctly and professionally! The sound dampening material comes in handy size sheets which make it easier in terms of cutting and installation process!
• Sound deadening material specifications: Nominal thickness 80 mil; Total coverage area of 36 sq.feet; Number of sheets in the stack 34; Nominal sheet Size 15.7x9.8 inch. Roller is not included.

User questions & answers

Question:	Does this product contain Asphalt
Answer:	We recommend covering the entire floor for it to be the most effective and double layer on the wheel wells.
Question:	Will it stick to plastic of a UTV
Answer:	Yes, you can install a headliner on top of Noico 80 mil 10 sqft material.
Question:	Does this come with the tool to roll on
Answer:	No smell or odor other than the initial opening of the package, I did however allow a day for it to dissipate before installing (has been installed for 30+ days in FL sun). Use caution when installing as mix will come out the edges & stick to roller. Use metal tape to seal edges.
Question:	How come what i just ordered was nothing like it was before i ordered 2 packs but this stuff is definitly not 80mil and there was no where near 36sqft
Answer:	Yes it should stick just fine as long as you make sure it's clean and free of debris. I'd guess 2 packs would be pretty close for 1 door (20 sq ft total)

• The cost effective 50 mil automotive butyl and foil sound deadening! You are not just buying an excellent quality product but also saving more than 20% comparing to competitors as well!
• Now everyone can easily eliminate the annoying road noise in the vehicle. We've designed the product that pretty efficiently handles the rattle and reduces noise while being affordable to almost everyone. Kilmat would deaden the entire car for the same money that would be enough to only insulate the doors using the expensive brands material.
• Automotive self-adhesive insulation consists of butyl. KILMAT sound deadening has a total weight of 0.35 lbs/1sqft. This weight ensures optimum efficiency and sound insulation that could be possibly gained from 50 mil thickness material. KILMAT 50 mil is light weighted sound deadening material!
• Car insulation KILMAT has a special indicator as to if it is installed correctly. The special embossing on the foil must be rolled out with a roller till it is plain smooth, then you'll be 100% sure that the soundproofing is set correctly and professionally! The sound dampening material comes in handy size sheets which make it easier in terms of cutting and installation process!
• Sound deadening material specifications: Nominal thickness 50 mil; Total coverage area of 50 sq.feet; Number of sheets in the stack 47; Nominal sheet Size 9.8x15.7 inch. Roller is not included.

User questions & answers

Question:	I want to use it under the headliner of the car. should i use some adhesive to apply this product kilmat to the ceiling? it would go a headlined over
Answer:	Kilmat 50 mil material is self adhesive, there is no need for additional adhesive to be applied to install it to the roof of a car, It's important to clean, dry and degrease a metal surface prior to installation of Kilmat 50 mil to it. Make sure to thoroughly press it down to the metal surface with a roller until the special embossment on the foil is plain and smooth.
Question:	What is R valuer
Answer:	i'm no expert. I would venture to say between 5 and 8 R value
Question:	What's the R value
Answer:	Yeah almost nothing. Found out the hard way. I saw peoole saying it's used for thermal insulation also. Did most of my van with other stuff there rely good but decided to giveth the last 20 percent worth this. And when I step on it like steering in the metal. No difference.
Question:	For application to underside of car hood, should I also use a spray adhesive
Answer:	There should not be a problem adhering Kilmat 50 mil to the underside of the hood without using additional spray adhesive, thus we do not recommend any additional spray adhesives. Make sure to clean and degrease the surface prior to installation.

Product description

Frost King Natural Cotton Denim Insulation - No itch insulation. Made from 100% recycled denim. This multipurpose insulation is natural and completely nonirritating. Effective uses include insulation, cushioning, and noise dampening. This easy-to-use insulation can be cut or torn to fit pipes and ducts, walls in between joists, etc. Mold-resistant, mildew-resistant, fire-resistant. No warning or precautions necessary; can be handled/installed with no need for gloves, goggles, masks. Plus it is because it is 100% recyclable. 16" W. x 1" thick x 48" L. - Size: 16 In. x 48 In., Material: 100% Recycled Denim, Thickness: 1 In., Pkg Qty: 1, Package Type: Bag

• Use For Insulating, Cushioning, And Noise Dampening
• Safe Alternative - No Gloves, Face Mask, Or Goggles Needed
• Cut Or Rip To Fit Pipes And Ducts, Walls, And Much More
• Brand Name: Frost King

User questions & answers

Question:	How many fleece liners could i make out of what comes in 1 pack of this
Answer:	Its super thin and I think it's 1 sheet... (could have been 2 , can't remember, was a while back - check the product details!!) not sure what you're looking for but I was using for soundproofing and was a disappointment. It's a tiny thin sheet of denim. The "1 inch" thickness is more like a 1/4 inch. Better to buy foam at a foam shop. I've had bad luck on Amazon with foam/denim products.
Question:	Does this smell
Answer:	No odor at all
Question:	Could I use this as an eco filler for a quilt ? Is it purely shredded denim or has it been pre treated with any chemicals
Answer:	Yes
Question:	What is the R value
Answer:	It says the R value is 4 on the package which means resistance to heat flow. The higher the R value,the greater the insulating power. Thats all I can find. I dont know if that number is higher or lower.

Product features

Frost King CF1 "No Itch" Natural Cotton Multi-Purpose Insulation, 16 x 1 x 48-Inch

With Frost King Natural Cotton Insulation, you don't need gloves, a face mask or goggles - it's completely safe and easy to install, yet provides maximum insulating power.

Cut it, rip it or just fit it into your ducts, walls or anyplace that needs a quick bit of insulating. It comes in different sizes and lengths to fit your needs.

• ★ Siless VIBRO 50 mil is ultimate quality sound deadening insulation. Designed for the automotive industry as an industrial sound damping material for applications that need extreme performance, it is well suited to the demanding car enthusiast as well.
• ★ Advanced Formulation - SILESS VIBRO Damping Material consists of newly invented Bmastic, technologically most advanced and efficient sound deadening composition on the market today.
• ★ Value - SILESS VIBRO Damping Material is just under $1.29 per sqft, priced to be cost effective, when compared to similar products on the market. Car soundproofing does not have to be expensive to work!!
• ★ Ease of Installation — SILESS VIBRO Damping Material is easy to install with a “peel and place” application. Simply trim the pieces to fit, peel and place and hand roll to ensure good adhesion. No messy spray-on paints or adhesives are needed to install this product.
• ★ SILESS VIBRO specifications — Thickness 50 mil, Each sheet size 23.6x15.94 inch. Installation instruction is included in the box.

User questions & answers

Question:	Does your material absorb water? How to make sure that rust not coming between it and metal
Answer:	Thank you for your question. If Siless is installed properly using our instructions, rolled and fully applied to the area, there is absolutely no worry for rust after installation. As a piece of mind, we would recommend installation of special aluminum tape on the top.
Question:	If I remove it in the future, paint on the car would be damaged
Answer:	Thank you for your question. Yes, you can remove it in the future using a heat gun, and whatever residue would be left, you can use solvent to remove it completely. If paint wasn’t damaged before, it wouldn’t be damaged after removal.
Question:	is this all butyl rubber
Answer:	Thank you for your question. Yes, It is butyl and foil.
Question:	is this made in USA
Answer:	Thank you for your question. Unlike many sellers on Amazon who sell their products from China, Siless products are proudly made in the Ukraine, one of the closest United States ally in the world.

• Closed Cell Foam: OIL and Waterproof LINER closed-cell polyethylene foam is the best for car, Siless with an adhesive layer 100% ensures optimum efficiency and thermal insulation that could be possibly gained. The price of 1 sqft of Siless Liner with similar characteristics is more then three times cheaper! Excellent quality for less money!!
• Heat Blocker and Vibration Deadener: Effectively blocks 98% of radiant heat transfer. Siless Liner is a very versatile insulation material with excellent thermal barrier properties that will block engine, exhaust, & summer heat, ensure your vehicle stays cooler in the summer and warmer in the winter, making your ride more pleasant!
• Lightweight, Waterproof: It is a waterproof light-weight thermal deadener with highly compressible closed cell foam formulation, it absolutely doesn’t absorb moisture and has no odor, and it’s flexible which make it easy to install with or without roller.
• The operating temperature of the material is the same as of the rubber foam up to 215 degrees Fahrenheit.
• SILESS Liner specifications: Self-adhesive foam rolls (closed cell PE foam) with waterproof glue. Thickness 157 mil / 0.157 inches / 4mm. Number of rolls in the package - 1. Total coverage area - 36 ft². Each roll size - 15.74 x 330.7 inches.

User questions & answers

Question:	Enough for 4 doors
Answer:
Question:	What color is the exposed side
Answer:
Question:	How does this compare to noico products? Seem pretty close in product
Answer:
Question:	What is the width of the roll
Answer:

Product description

The Thermo-Tec Adhesive Backed Heat Barrier protects parts and components from radiant heat. It can be used in applications to protect painted surfaces, plastic parts or any component from the damaging effects of radiant heat. Adhesive Backed Heat Barrier is made up of woven silica with a flexible aluminized finish. The highly reflective surface of the material is capable of withstanding radiant temperatures up to 2000 degrees Fahrenheit. The adhesive backed side handles direct and continuous temperatures up to 300 degrees Fahrenheit. The adhesive backed composite construction material can easily be applied to any surface or wrapped around a hose or wire to make a clean professional appearance.

• Protect parts and components, like painted surfaces and plastic parts, from damaging radiant heat
• Made up of woven silica with a flexible aluminized finish
• Highly reflective surface of the material is capable of withstanding radiant temperatures up to 2000 degrees Fahrenheit
• Adhesive backed side handles direct and continuous temperatures up to 300 degrees Fahrenheit
• Can easily be applied to any surface or wrapped around a hose or wire to make a clean professional appearance

User questions & answers

Question:	How thick is the material
Answer:	Once peeled and pasted, it is maybe the thickness of say, an average envelope with one single letter size paper folded in 3 inside, give or take. It isn't very thick but it seems to do the job and even pasted upside down (in my case on the outside bottom of my saddlebag an inch over my exhaust pipe) it holds very nicely. Mine has been there for now six months and 5,000 miles with a few biblical rain storms. Good stuff.
Question:	Can this be used to cover a hot air heating vent? I want to prevent the hot air from entering into rooms
Answer:	by itself I would think the adhesive side wouldn't last too long against the air flow. Now if you paste it on some board that you then screw on top of the vent, I don't see why not. Just a guess for what that's worth.
Question:	Can I use this to wrap a leaking muffler
Answer:	No. Muffler has comes out at pressure. Look at the products website and it well tell you for sure. If it doesn't say you can't, it doesn't mean you can
Question:	Has anyone actually wrapped (direct contact) this product around an exhaust header? If so, your experience & assessment would be much appreciated. thx
Answer:	I doubt if there is any product made to wrap around headers for the purpose of keeping heat from other products. You want your headers to dissapate heat. If you have rubber control arms or your tubes are so close to metal, stater etc that they execessively heat then you buy protection for that. You protect ancillary parts against the heat of your headers.

Product features

Thermo-Tec 13575 Adhesive Backed Aluminized Heat Barrier, 12" x 24"

The Adhesive Backed Heat Barrier protects parts and components from radiant heat. It can be used in applications to protect painted surfaces, plastic parts or any component from the damaging effects of radiant heat. Adhesive Backed Heat Barrier is made up of woven silica with a flexible aluminized finish. The highly reflective surface of the material is capable of withstanding radiant temperatures up to 2000°F. The adhesive backed side handles direct and continuous temperatures up to 300ºF. The adhesive backed composite construction material can easily be applied to any surface or wrapped around a hose or wire to make a clean professional appearance.

Product description

Description:



Insulation Mat Acoustic Dampening Heat, Sound deadener Sound Proof Sticker



100% Brand New

Metal:PE with aluminum and self-adhesive

Covered with Alumium foil

Thickness: 6mm

Strong sound insulation and absorption performance,heat insulation, damping and

Reducing energy consumption with strong performance of heat insution

Strong self-viscous performance

Strong shock resistance

Making sound more centralized and harmony by changing the way of sound transmission



Installation:

1, Remove the door panels

2, Install the screws back in original place, it will easy be found when you mount, avoiding holes be covered

3, With roller tools will make insulation materials and sheet metal firm fit, and play best adhesive, damping performance

4, According to the effect you want choose construction program, only single Soundproof/Damping Plate or single Heat Noise Insulation Cotton or Both them.

5, You can also use on car roof floors, hood , firewall, chassis, trunk room, trunk lid and so on.. Do not cover the chassis wiring or air holes.

• Strong sound insulation and absorption performance,heat insulation, damping and
• Keeps Heat In-Cold Out in the Winter, Keeps Cold in-Heat Out in the Summer.In the winter, the engine temperature is very high, but outside is very low when driving, which make car parts damaged easier
• The surface high-fiber cloth is fiberglass. Heatproof .Block transmit sunlight, engine, exhaust pipe heat to the cab, reduce air conditioning energy consumption, saving fuel
• Slow down the car paint ageing.Because of hot weather, the front outer cover through the direct sun, high temperature inside and outside the engine, accelerated paint aging
• You can also use on car roof floors, hood , firewall, chassis, trunk room, trunk lid and so on.. Do not cover the chassis wiring or air holes.

User questions & answers

Question:	How strong is the adhesive backing? I want to use it around the furnace in my house, which sucked the original insulation off the wall. Will it stick
Answer:	We are sorry but all our materials, incuding Noico RED 315 mil 20 sqft, are intended for automotive application only. We recommend looking for residential type of insulation in a construction store.
Question:	Could this be used for your engine bay
Answer:	Please note that adhesion side of Noico Red 315 mil material is red. Whereas the non-stick side (finish surface) that might be visible is grey.
Question:	how water resistant is this
Answer:	Yes there are Fumes,For my trailer Floor/Sleeping Area i used Foam Reflective instulation,the Foam lined not bubble And to be thin its Soft.+ reflects heat back
Question:	What do you he’s of be strong enough to put on an exhaust heat shield
Answer:	We do not recommend to use any spray adhesive type of spray material over the layer of Noico Red due to peculiarities of the finishing surface of this material, it's difficult to anticipate how well the glue will adhere to both Noico Red and the headliner's material .

• Closed Cell Foam: OIL and Waterproof Liner closed-cell polyethylene foam is the best for car, Siless with an adhesive layer 100% ensures optimum efficiency and thermal insulation that could be possibly gained. The price of 1 sqft of Siless Liner with similar characteristics is more then three times cheaper! Excellent quality for less money!!
• Heat Blocker and Vibration Deadener: Effectively blocks 98% of radiant heat transfer. Siless Liner is a very versatile insulation material with excellent thermal barrier properties that will block engine, exhaust, & summer heat, ensure your vehicle stays cooler in the summer and warmer in the winter, making your ride more pleasant!
• Lightweight, Waterproof: It is a waterproof light-weight thermal deadener with highly compressible closed cell foam formulation, it absolutely doesn’t absorb moisture and has no odor, and it’s flexible which make it easy to install with or without roller.
• The operating temperature of the material is the same as of the rubber foam up to 215 degrees Fahrenheit.
• SILESS Liner specifications: Self-adhesive foam rolls (closed cell PE foam) with waterproof glue. Thickness 157 mil / 0.157 inches / 4mm. Number of rolls in the package - 2 x 7.5 sqft. Total coverage area - 15 ft². Each roll size - 15.74 x 68.68 inches.

User questions & answers

Question:	For the seller: Would this work in my transmission tunnel (old matting has fallen off)? If you do not know, please don't answer
Answer:	I did not stick mine directly to the wall. I used and adhesive from Lowes called "Power Grab" and stuck mine to a sandwich of two acoustic insulation boards with sound blocking vinyl in between. (Many thanks to the company that showed their product in a cut away view) then I glued the BXI panels to that. My panels are 1 foot by 4 feet and are arranged in two colors green on top and white on the bottom. Good luck on your project!
Question:	Are there chemical additives to the Polyethylene to make it flame retardant? If so, what are they
Answer:	They do not work to block traffic noise on windows. I purchased this product, did not change the noise level at the window next to my desk.
Question:	How long? How wide
Answer:	Not unless you covered the entire wall with them
Question:	so just to confirm. I can use this for the hood of my car
Answer:	Good enough

• FIRE PROOF INSULATION: Ceramic fiber blanket insulation, rated to 2400 F
• PRODUCT SPECIFICATIONS: 1/2" Thick x 12" X 24", density 8 lb/ft3, made in the USA
• USES: Wood stove baffle, fireplace, pellet stove, chimney, furnace, boiler, pizza ovens and forge
• USES: Brazing, soldering, welding, foundry, kiln, refractory, glass blowing, and jewelry making
• SAFETY: See Important Safety Information below

User questions & answers

Question:	Can this be cut with scissors? Replacing a circular asbestos baffle inside a marine kerosene heater
Answer:	As long as the scissors are sharp, it shouldn't be a problem. I cut mine with a box cutter without any problems.
Question:	Can this be used to make a homemade Raku kiln
Answer:	Yes, this is the right material.
Question:	Can it be used for fire pit insulation between burner and bottom of cast fire pit
Answer:	Yes, this will work well for that application
Question:	I’m thinking about lining my foundry with this. Do I need a coating for it? Can it withstand a constant propane torch on it
Answer:	Don't know about a propane torch, but it doesn't need any coating in the wood burner, and it gets hot enough inside to melt aluminum at least, possibly more.

Product features

Kaowool Ceramic Blankets

High temperature stability: Kaowool ceramic insulation blanket withstands direct flame, continuous use at 2200 ℉, intermittent use at 2400 ℉. Above 2400 ℉ it will begin to shrink, become brittle and eventually melt at 3200 ℉.

Thermal conductivity: The R-value is approximately 2.5 per inch. For a 1000 ℉ hot face with 1" of insulation, expect the cold face of the insulation to be 220 ℉.

Installation: Mechanical fastening or high temperature adhesive such as sodium silicate, refractory cement or RTV silicone.

Quality: Made from premium 8lb density Cerablanket that has high insulating value, strength & durability. Made in the USA by ISO 9001 certified Morgan Thermal Ceramics.

Chemical composition: 46% alumina, 54% silica and less than 1% impurities.

Uses: Fireplace insert insulation, baffle blankets, wood stove insulation, kiln insulation, blacksmith forge, pizza ovens, brazing, soldering blanket, welding, pellet stove, chimney lining, furnace insulation, boiler, foundries, refractory wool , glass blowing, jewelry making, fireproof doors, fireplace insulation, muffler packing.

Product history: Kaowool was the original ceramic blanket which has been improved and replaced by Cerablanket. Cerablanket has lower impurities and is superior to Kaowool in all properties. This listing is Cerablanket.

Also known as: Kaowool, Inswool, Durablanket, Cerablanket, TaoFiber, Fiberfrax, Ceramic Wool

• The cost effective 150 mil closed cell foam sound deadening material on Amazon! You are not just buying an excellent quality product but also saving more than 20% comparing to competitors as well!
• Noico 150 mil is a very versatile insulation material with excellent thermal barrier properties. It is the best way to make the car cool and quiet! It’s easy to cut and install!
• Noico 150 mil has the same characteristics and excellent noise insulator properties as rubber foam. It absolutely doesn’t absorb water & has no odor unlike polyurethane foam. It has a very low weight, oil and petrol resistant. The sound deadener material allows you to deal with both, cold and the heat. This is especially important in hot climate areas. Well-insulated interior is a pledge of high comfort while in vehicle.
• The operating temperature of the material is the same as of the rubber foam – up to 190 degrees Fahrenheit. DO NOT use this product as heat shield for mufflers, catalytic converters, DPF and more. In this case, you need to use special materials designed for 900-3000 degrees F.
• Sound deadening material specifications: Nominal thickness 150 mil; Total coverage area of 36 sq. feet; Number of sheets in the stack 34; Nominal sheet Size 15.7x9.8 inch.

User questions & answers

Question:	what is the abrasion resistance of this material to be used in a trunk space
Answer:	This material is just foam with adhesive backing. It needs something on top of it to protect it. Typically you would put mass loaded vinyl on top of it as part of a butyl, foam, vinyl sandwich for the best sound deadening and resonance control. You can also just put carpet over it.
Question:	What is the max temp rating for this product? What could I use to insulate up to 900*F
Answer:	Noico RED 150 mil temperature limits are from -49 degrees F to +190 degrees Fahrenheit. In your situation, you need to use special materials designed for 900-3000 degrees F. We're sorry, but we do not carry such type of materials.
Question:	Can i use this on the hood of my 82 wagoneer
Answer:	DEI has hood liners. I have their silver one which is working great and hasn't peeled off in the 6 months I've had it on. And it cut down on engine noise a lot. It's only like $60 on amazon last I checked. Their black version is newer.
Question:	So this is a secondary layer to work together with kilmat or something? And would it place on top of it or on the other side
Answer:	If you want to use Noico Red 150 mil material in combination with butyl based sound deadening material, then the installation plan will be as follows: 1 layer: butyl based sound deadening material with thickness around 80 mil installed on pre-cleaned and degreased metal surface of a vehicle; thoroughly pressed down to the metal surface with a roller 2nd layer: Noico Red 150 mil installed on top of the layer of butyl based material Please note, all sound deadening materials are to be installed only from the interior side.

Product description

EZ Cool Car Insulation Kit(Includes 100 Sq. Ft Insulation, 25' Foil Tape): Heat and Sound Automotive Insulation For Your Car EZ Cool Is part of the Super Shield Family of products and is the ideal Insulation for Hot Rods, Street Rods, Race Cars, Vintage Autos, Trucks, Vans, Motor Homes, Boats, and More. For use in Automotive Firewalls, Car Doors, Headliners, Hoods and Speaker Boxes. This foil and waterproof foam (not Bubble packaging Material) product helps by reducing road and vibration noise, Lowering heat in cab or hood and providing water protective membrane everywhere it is adhered to. Super Shield EZ Cool is indoor air quality approved and mold and mildew resistant. Pliable and moldable for easy application with 25 Feet of pure foil tape for seams included. Spray adhesive at limited areas holds everything in place as EZ Cool is extremely lightweight. Used in IROC Series as well as newly constructed Ambulance, Firetruck and Military vehicles EZ Cool provides heat and sound reduction for comfort. 10 foot kit is ideal for either firewall, doors, headliner or hood. 25 foot Kit available for when you are doing multiple applications on the same car. Super Shield EZ-Cool Car Insulation Kit(Includes 100 Sq. Ft Insulation, 25' Foil Tape): Heat and Sound Automotive Insulation For Your Car Restoration Projects Puncture, Crush and Water Resisant Lightweight, Flexible, Easy to cut and Handle Long Lasting, Non Toxic Stops Heat, Deadens Sound, Won't Absorb Moisture

• Vehicle Insulation Kit - Thermal Sound Deadener 100 Sqft (4x25) - Lightweight Automotive Heat Barrier w/ 25ft of Foil Tape and Razor
• Thermal Heat Barrier: Reflects 99.97% Heat Transfer / R8 / Radiant Barrier and R Value in 1
• Sound Deadener: Reduces Sound Transfer / Vibrations / Noises Throughout
• Material: 1/4 inch Thick / Water Proof and Weather Proof / Will Not Discolor or Fade / Strong / Durable / Light Weight / Flexible / Easy to Work With
• Made in USA / SHIPS From USA / Ships Super Fast

User questions & answers

Question:	What is the thickness
Answer:	EZ Cool is 3/16 inch thick
Question:	Can this be used as a vapor barrier over Thinsulate? (in a camper van conversion
Answer:	I used it as a vapor/reflective barrier over fat max then thinsulate. It works really well for both temp and noise. I wouldn’t skip the fatmat or Kilmat layer.
Question:	Is the foam in the middle closed-cell foam
Answer:	Yes it is a closed cell polyethylene micro foam.
Question:	Hello there l, how many i need to do in a complete new dodge challenger
Answer:	The 4' x 25' roll should cover all of the inside of your Challenger

• The cost effective 80 mil automotive butyl and foil sound deadening! You are not just buying an excellent quality product but also saving more than 20% comparing to competitors as well!
• Now the material is 1,5 times thicker that will get you 1,5 times more effective insulation. Noico 80 mil is 1,5 times better in comparison to sound deadening material of 50 mil. The thicker the material the more performance you get!
• Automotive self-adhesive insulation consists of butyl. Noico sound deadening has a total weight of 0.7 lbs/1sqft. This weight ensures maximum efficiency and sound insulation that could be possibly gained from 80 mil thickness material. Noico 80 mil is full weighted sound deadening material!
• Audio insulation Noico has a special indicator as to if it is installed correctly. The special embossing on the foil must be rolled out with a roller till it is plain smooth, then you'll be 100% sure that the insulation is set correctly and professionally! The sound dampening material comes in handy size sheets which make it easier in terms of cutting and installation process!
• Sound deadening material specifications: Nominal thickness 80 mil; Total coverage area of 10 sq.feet; Number of sheets in the stack 10 (sheets are folded); Nominal sheet Size 14,5x10 inch. Roller is not included.

User questions & answers

Question:	does the entire floor needs to covered for this to be effective
Answer:	I believe all PC case fans run on 12 volts
Question:	Can headliner be applied on top of this
Answer:	Yrs
Question:	Notice any smell or odor
Answer:	Mine (the 101 model) did *NOT* come with any screws. Fortunately I have a box of loose screws at work...
Question:	Can i use this on a wooden door at home? How many do i need
Answer:	I am not using Cooler Master, but corsair H110 (also 280mm cooler). It fits on the top, except one problem: Water pipe clearance is small and I decided to move DVD drive to external one. If you do not mind bending the water pipe, it fits, but I am not so happy about the fact that water pipe touches the dvd drive.

• ★ Siless VIBRO 80 mil is ultimate quality sound deadening insulation. Designed for the automotive industry as an industrial sound damping material for applications that need extreme performance, it is well suited to the demanding car enthusiast as well.
• ★ Advanced Formulation - SILESS VIBRO Damping Material consists of newly invented Bmastic, technologically most advanced and efficient sound deadening composition on the market today.
• ★ Value - SILESS VIBRO Damping Material is just under $1.53 per sqft, priced to be cost effective, when compared to similar products on the market. Car soundproofing does not have to be expensive to work!!
• ★ Ease of Installation — SILESS VIBRO Damping Material is easy to install with a “peel and place” application. Simply trim the pieces to fit, peel and place and hand roll to ensure good adhesion. No messy spray-on paints or adhesives are needed to install this product.
• ★ SILESS VIBRO specifications — Thickness 80 mil/ 0.08 inches/ 2mm, Coverage area - 36 ft², Number of sheets in the box - 14, each sheet size - 23.6x15.94 inches. The installation instructions are included in the package but a roller isn't.

User questions & answers

Question:	The chart shows I need 34sqft for a ram crew cab . Does that include inside the doors too? Also, the 36sqft says it has 14 sheets, is that correct
Answer:	Thank you for your question. Yes, the box of Siless Vibro 80 mil 36 sqft has 14 sheets in it. The chart shows that you would need 85 sqft a ram crew cab. 34 sqft would be enough to do doors.
Question:	is this made in china
Answer:	Thank you for your question. Unlike many sound deadening materials currently sold on Amazon from China and Russian Federation, Siless sound deadening mat made in Ukraine.
Question:	Could you use this to keep music room noise from bothering neighbors? Specifically, could you put it on a wall
Answer:	You could put it on walls. But as for suppressing noise from a neighbor, I don't think so. It's best to use acoustical tile for rooms.
Question:	Can this be used a a heat sheild for a Wood stove
Answer:	Thank you for your question. Siless 80 mil sound deadening mat is not recommended to be used as a heat shield for wood stove.