14 best dirty water submersible pumps

Product description

This portable sump pump is a necessity of every house. Never worry again that your dry basement will be effected on rainy days or any day that the underground water table rises. Submersible sump pumps sit in a water-accumulating sump pit, they pump all excess water away from the house’s foundation. This sump pump’s advantage is that it has a higher base plate which assures the prevention of debris collection in the sump pit. - ½ HP - Maximum flow of 2,000 gallons of water per hour - Adjustable tether switch - Multi fitting elbow - Extra long cord - Sealed specially in order to prevent electrical short circuits while under water. - Portable, does not have to be permanently installed. The purchase of this sump pump will save any home owner thousands of dollars by preventing water in the home’s basement The appliance is intended for pumping rainwater, fresh water, mains water and chlorinated swimming pool water. It must not be used for the drinking water supply or for the delivery of foodstuffs. Explosive, flammable, aggressive or health-hazardous substances and fecal matter must not be pumped. The appliance is not suitable for commercial or industrial use. The appliance is not suitable for continuous running (e.g. permanent circulation in filter systems.) It is also not suitable for use with liquids containing abrasive materials or containing mixtures of dirt, sand, mud or clay. Connections: The connection must be made to earthed sockets which have been properly installed earthed and tested. Main voltage and fuse must comply with the technical data. During operation for swimming pools, garden ponds, and similar places, the appliance must be equipped with a residual circuit breaker (RCCB) with a design fault current of not more than 30 mA. Do not kink, crush, drag, or drive over the mains cable; protect against sharp edges, oil and heat. Extension cables MUST NOT be used.

• Powered By A Durable, Oil-Cooled Electric Motor
• Max Submersion Depth: 16.5FT
• Various Fittings for Outflow Included
• Max Delivery Height: 23FT
• Voltage: 110V/115V, 60Hz

User questions & answers

Question:	Would this one work good for 300 gallon hot tub
Answer:	Probably. My sump is tied into 1.25" PVC pipe, which was a pain. IIRC, there is a universal adaptor that should connect to a garden hose. The instructions note you should not use an extension cord and they refer to an outlet that is properly grounded (GFCI?). For a 300-gal hot tub, you might prefer using a drill-powered pump (less than $10). Connect a hose to each end (tub to pump, pump to yard, etc.) and put a regular drill onto the pump, and they work with little effort. For the record, I let my 500-gal hot tub drain by gravity through a garden hose into the back yard (i.e., away from the foundation).
Question:	where exactly is the float mech - some say attached to cord, and other say will not work unless water is 1 foot above pump
Answer:	It's a bobber switch and in order to operate it under 1 foot, you simply tie the bobber up so that the pump stays on
Question:	How would you connect this to a 3/4 PVC pipe? instead of a flex tube
Answer:	just use the threaded output to pvc
Question:	how do i get this pump warranty information
Answer:	Manufacturers number is 717-887-8799; the pump I purchased has stopped working but they have agreed to replace/exchange it

Product description

DEKO Submersible Water Pump Is Great for Draining Garden Pond, Water Tanks, Pools, Hot Tubs, Flooded Areas, etc. It Will Be A Necessary Tool For Every House.

The pump give you the excellent ability to drain cellars, swimming pool or garden ponds.

Perfect for household and utility applications of transferring water from one place to another.



Specifications:

Power: 750W

Material: Plastic and Metal

Voltage: 110V 60Hz

Qmax:3,302gallon/H（12500L/H ）

H.Max: 26.2ft (8m)

Power Cord Length:16 feet

Type: Water Pump

Diameter of Pipe: 1",G1",1-1/4",G1-1/2"(From Up to Down)

Applications: Garden, Yard,Swimming pool, Pond, Flooded area



Package Contents:

1 * Water Pump

1 * User Manual

• POWERFUL SUMP PUMP:750 Watt, 1 HP motor. Max Lift: 16 Feet; 3302 Gallon Per Hour rating tackles any draining job at a fraction of the time. This pump easily passes solids up to 1" in diameter. GREAT for flooded area, swimming pools, cellars or garden pond.
• MULTI OUTLET SIZE:Compatible with 1-1/4" and 1-1/2" hoses. Three fittings with different diameters for outflow(1",1.25",1.5" ) to choose from according to the flow rate.
• AUTO FLOAT SWITCH:Start/stop automatically. When water level is below 4.7 inch, it will automatically disconnect the power; when water level rises above 4.7 inch, the pump will start again. Cut off immediately when pump fails to pump water to prevent the coil from getting burned.
• HIGH-QUALITY MATERIALS:Thermoplastic composite material is highly rugged. Designed and manufactured in line with the valid safety requirements. Thermoplastic body resists corrosion as there are not exposed metal parts. Lower noise and energy-efficient. Oil free motor requires no maintenance.
• GREAT FOR DRAINING:Great to Drain the Dirty Water from the Pond, Garden Pond, or Water Tanks. Great to move water for garden irrigation or cleaning your yard or road.

User questions & answers

Question:	How big of tank does it nerd to sitin to keep recycling my waterfall and stream? I have it in a 50 gallon barrel but it keeps running out of water
Answer:	I’m using a 20 gal
Question:	will the DEKO 1 ho pump fit into a 7 inch pipe
Answer:	No, the pump is just over 7 inch around. I would say a 9 inch pipe would work
Question:	can it be throttled? Gotta drain a 50k pool with no sewer clean out so it'll have to go in the bathtub drain. Don't wanna have to babysit it all day
Answer:	No. Drains at same speed as long as the water is there
Question:	Can I just screw a garden hose to it
Answer:	garden hose did not fit but I had another attachment that fit well.

Product features

Product description:

The water pumps give you the excellent ability to drain cellars, swimming pool or garden ponds.

Perfect for household and utility applications of transferring water from one place to another.

DEKO 1HP 3302GPH 750W Submersible Pump

Design and manufacture according to effective safety requirements.

Applicable Scene : Remove stagnant water from any environment, suitable for use in farms, flat roofs, swimming pools, fountains, flooded basements, and drainage in typical residential or commercial water transfer applications.

Multiple hose fitting

Three outlet with different to choose from(1" ,1-1/4" ,1-1/2")

Power motor

Strong suction and filtration capabilities, even in sewage.

Semi-hidden handle

Hand-designed handle for easy carrying,occupy little space.

Lower noise

Under 30DB, lower noise and energy efficiency.

Product description

Superior Pump builds pumps that are truly Built to Last and are 100 percent factory tested. Superior Pump uses quality components including solid copper motor windings, heavy duty stainless steel jacketed shaft seals, double o-ring seals on motor plate, and electronically controlled split capacitors. Superior Pump model 91250, 1/4 HP thermoplastic submersible utility pump with 10 foot power cord and ¾-inch garden hose adapter, will move water up to 1800 gallons per hour. Equipped with suction screen to filter out large debris and handles up to 1/8-inch solids with ease. Base of the pump is designed to fit the hub of a standard 6-inch floor drain. This pump is UL/CUL listed and CSA certified and backed by a 1 year warranty.

From the Manufacturer

Superior Pump is a family owned and operated Pump Company specializing in residential / light commercial duty pumps. Headquartered in Minneapolis, Minnesota, Superior Pump was founded in 1999 after spending years in the pump industry dating back to the 70's, and with a plumbing background starting in St Paul Minnesota dating all the way back to 1885. Superior Pump adheres to our strong core family values, selling the absolute highest quality product possible. Known for building durable pumps, Superior Pump concentrates on quality throughout the engineering, manufacturing and testing processes. Quality products, strong warranties, excellent USA based customer service - Superior Pumps Built to Last!

• 1/4 HP Utility pump moves up to 1,800 gallons per hour; pump will lift water up to 25' of vertical height
• Tough thermoplastic construction; 10' cord length
• 1-1/4 inch NPT discharge for high capacity pumping; includes 3/4 inch garden hose adapter
• Removable suction screen and handles up to 1/8 inch solids
• Superior Pumps are Built to Last, engineered with quality components and are 100% factory tested

User questions & answers

Question:	What's the PSI or max head (pumping vertical height) of this pump
Answer:	A quick Google search of "Superior Pump 91250" yields the manufacturers specs. I do not see PSI listed but "Pumps will lift water up to 25' of vertical height" I belive answers your question...there is a chart on the "Performance" tab that shows 30 GPM at 0' lift and 2 GPM at 25' lift...with flow rates every 5' listed.http://superiorpump.com/products/utility/91250.html
Question:	Does it have an automatic shut off
Answer:	The pump does not have an automatic shut off. I added a float switch because I wanted it to pump out a sink that had a slow-running clogged drain where I had the washing machine. When the sink was mostly pumped out the float switch turned off the pump. It worked great for a couple years until I got around to dealing with snaking the drain which didn't have an easy clean-out. This is a good pump, since the sink drain got taken care of, we've been using the pump to pump koi pond water over a 5' fence to our neighbor's garden using about 150' of garden hose. The pump runs continuously for 5+ hours without issues in this process.
Question:	Will clothes washer hoses fit on this pump
Answer:	The pump itself fits a garden hose nicely. You can buy the attachment package listed next to it for the converter piece. It only came to around $8.00. It also comes with a larger hose. I didn't need it for my spa but if you need to empty a washer or bigger pool it seems like it would come in handy. Hope that helps. Good luck. :-)
Question:	Can this be user to flush a tankless heater with vinigar
Answer:	I bought the pump for this very reason. I'm not sure if it is rated to handle vinegar, but at the price I figured I'd try it and see. I have two tankless water heaters, and I wanted a pump that could clean out both at the same time and this pump certainly does the job. I have a hose that runs from the pump, into a splitter. From the splitter I have two hoses going to each water heater (one hose per water heater). Even pushing water through two hoses, it still has a strong flow, with each hose pushing about the same flow as the water hose faucet outside your house opened wide open (guestimate). The splitter I have allows me to adjust the flow rate by closing off some valves if it is too strong. For just one water heater, i would think this pump is too strong (as it REALLY moves water), but I'm not a plumber so I couldn't say for sure. If I were to do it again, I think I would have purchased the 1/4 HP pump, or even the 1/5HP for cleaning out water heaters with vinegar. I cleaned out my water heater this week for the first time using this pump. I let it run for 2 hrs, and I noticed that it got warm (about the temp of a warm-to-hot bath). I'm not sure if that is normal, but thought I'd let you know.

Product features

Superior Pump 91250 1/4 HP Thermoplastic Utility Pump

Superior Pump builds pumps that are truly Built to Last. Superior Pump uses quality components including solid copper motor windings, heavy duty stainless steel jacketed shaft seals, double o-ring seals on motor plate, and electronically controlled split capacitors. Superior Pump model 91250, 1/4 HP thermoplastic submersible utility pump will move water up to 1800 gallons per hour. Equipped with suction screen to filter out large debris and handles up to 1/8 inch solids with ease. This pump is UL/CUL listed (E238091, by UL, 2019) and CSA certified (230584, by CSA, 2019)

Construction and Discharge

• Thermoplastic construction is corrosion resistant and offers years of performance and reliability.
• 1-1/4 in. NPT discharge.
• 3/4 in. Garden hose adapter.

Multiple discharge hookup options

• Easily hook up to a Garden Hose* or Discharge hose* (*not included)
• Easy to transport using the carrying handle.
• 10 ft. power cord.

Intake Screen

• Intake screen filters out debris from entering the impeller. This helps reduce the clogging and prolongs the life of the pump.
• Easily to clean and is removable.

Motor and Performance

Motor:

• 1/4 HP Superior Pump continuous duty, thermally protected - split capacitor motor

Performance

• 1800 Gallons per hour at 0'
• 1200 Gallons per hour at 10'
• 540 Gallons per hour at 20'

Product description

The Tsurumi HSZ2.4S-62 is a semi-vortex submersible trash pump with agitator. It has a Urethane Semi Vortex Impeller for maximum durability and pump performance. It has an attached float switch for automatic operation. The optional accessories are: vertical discharge Coupling.

• 2-inch discharge and attached float switch for automatic operation
• 1/2-inch horse power
• 110/220 voltage
• 5.4 amps
• 20-foot cable length

User questions & answers

Question:	What’s the difference between 1 pack and 16/3 besides the $200 difference
Answer:	No the hose cant be cut, you'll loose all your investment and she might leave you. These hose ain't loyal
Question:	I want to use this to drain a pool that has a LOT of leaves in it. Do I need the 3 inch discharge for this
Answer:	Yes
Question:	How much gph it pumps
Answer:	23.5 inches
Question:	what voltage
Answer:	1 3/4

Product features

HSZ2.4S Auto Electric Submersible Pump

Automatic trash pump designed to pump sand, solids and debris with minimal wear and clogging.

About Tsurumi: The Pump Technology That The World Trusts

Tsurumi introduced its overseas strategy in the 1960s. Our technical capabilities gained recognition first in Asia in the 1970s and then in the United States and Europe in the 1980s.

Following these initial successes, we sought to accelerate the overseas strategy through our International Sales Division. Remarkable successes in fields including construction, civil engineering, mining, industrial wastewater, domestic wastewater, sewage treatment, flood control, facilities designed to bring people into closer contact with water, and scenery creation have proven Tsurumi’s creativity and capability to the world.

Today Tsurumi has expanded its bases of operations and is active in 45 countries and regions. In addition to supporting a variety of worksites, our high-performance pump products are widely used in large-scale national projects, where they fulfill their roles reliably.

Product description

The Tsurumi HS2.4S-62 is a semi-vortex submersible trash pump with agitator. The built-in shaft mounted agitator suspends solids. The urethane semi Vortex impeller is for maximum durability and pump performance. It features a double inside mechanical seal with sic faces that provides longest operational life. The oil lifter provides lubrication of the seal faces. (Patent pending) the V-ring seal protector protects mechanical seal from abrasive particles.

• 2-Inch discharge
• 1/2-inch horse power
• 110/220 voltage
• 5.4 amps
• 20-Foot cable length

User questions & answers

Question:	I'm looking to pump sand out so I can pull my boat up to the lift. With this pump work
Answer:	it is a submersible pump so long as the plug don't get wet
Question:	I need to pump out a pool that has leaves in it, will this work
Answer:	I use mine outdoor, submerged. The only thing I hear is thrush of water over my waterfall. And I have run it 24/7 for over a year with no problems. I bought a second one to drain my jacuzzi. Great product, & very dependable.
Question:	What is max distance it will push the water
Answer:	Not sure quarter inch too small half inch too big. Ended up using half inch tube with half inch hose clamp works great.
Question:	What is max distance it will push the water
Answer:	If your not concerned about how long it takes, I used it to pump out a much smaller volume and had to switch to a different pump. I used a Master submersible utility pump, model 540094-01, 1/4 HP, also available on Amazon, but about 4x more expensive. The FREESEA was taking forever. The Master pump has a garden hose size output.

Product description

DEKO Submersible Water Pump Is Great for Draining Garden Pond, Water Tanks, Pools, Hot Tubs, Flooded Areas, etc. It Will Be A Necessary Tool For Every House.

The pump give you the excellent ability to drain cellars, swimming pool or garden ponds.

Perfect for household and utility applications of transferring water from one place to another.



Specifications:

Power: 750W

Material: Plastic and Metal

Voltage: 110V 60Hz

Qmax:3,302gallon/H（12500L/H ）

H.Max: 26.2ft (8m)

Power Cord Length:16 feet

Type: Water Pump

Diameter of Pipe: 1"",G1"",1-1/4"",G1-1/2""(From Up to Down)

Applications: Garden, Yard,Swimming pool, Pond, Flooded area



Package Contents:

1 * Water Pump

1 * User Manual

• Great Performance: The submersible sump pump has professional-grade power. 1HP motor. Max Lift: 16 Feet; 3302 Gallon Per Hour rating tackles any draining job at a fraction of the time. This submersible water pump easily passes solids up to 1" in diameter.
• High Quality Materials: The sump pump is made of high quality thermoplastic composite material,which is anti-corrosion, acid and alkali resistant and waterproof. The higher base plate assures the prevention of debris collection in the sump pit.
• Auto Float Switch: Start/stop automatically. When water level is below 4.7 inch, it will automatically disconnect the power; when water level rises above 4.7 inch, the sump pump submersible will start again. Cut off immediately when pump fails to pump water to prevent the coil from getting burned.
• Ingenious Design: Compatible with 1-1/4" and 1-1/2" hoses. Three fittings with different diameters for outflow(1",1.25", 1.5") to choose from according to the flow rate. Built in thermal overload protection ensures the utility pump operates within spec for longer durability.
• Wide Application：Great for flooded area, swimming pools, cellars or garden pond. High Performance Energy-efficient Pumps designed for use in Ponds, Fountains, Waterfalls, Hydroponic systems, Irrigation systems and water features.

User questions & answers

Question:	How can you hook this to standard garden hose
Answer:	My small existing hose I push through the hole in the bracket, wrap the plastic and garden hose with strong holding tape together and use a small clamp and tighten it, It works. But being able to have an adapter on a small hose would save a lot of time or having the hose pushed out from the water pressure. Hope it helps because I went through this process 2/3 times before I got it right. Smile
Question:	Is this pump safe to be use with saltwater for aquarium? Would like to use to transfer from 1 holding tank to another
Answer:	I used it as a pump for a homemade pool filtration system for an 8000 gallon above ground pool that ran continuously for 5 weeks straight. Pool salts, sand, pine needles, and algae didn't stop this unit from working. A little salty water won't do anything to this unit.
Question:	Can you control the the pressure on the pump
Answer:	No it’s factory set
Question:	how do I connect this to a standard garden hose The attachments to a standard garden hose you would find at Walmart or any other hardware store do not
Answer:	Yes there is no way I could see to attach a garden hose. In the video in posted to my by review I show the pump projecting the water into the yard. I really couldn’t find any pump that showed a hose connection

Product description

FEATURES:

Newly Designed 2018 model

(UL) APPROVED/CE LISTED/CUL/GS

Suitable for Both indoor and outdoor

Powerful 20,000 liters per hour

Runs quietly and is extremely reliable

Minimum vibration and is completely submersible

Oil free, grease free magnetic motor to avoid pollution in your water

Removable upper and lower cover for easy cleaning

Comes with everything you need, simply plug-in and ready to use

Extra long 33ft (UL) cord with 3 different size prongs



Specification:

Power: 400 Watts

Voltage: 110V/60Hz

Discharge bore: 38mm Inlet Size: 1.5”

Outlet Size: 1.5”

Power Cord Length: 33FT

Dia of Pipe:1",1-1/4",1-1/2"

Material: Metal,Thermoplastic

Max Drainage Depth: 16.4ft(5m)

Dimensions: 12.6"(L) x 7"(W) x 8"(H)

Horsepower: 1/2 HP, Max Flow Rate: 2115GPH(8000l/h)

• 【Auto Float Switch】Start/stop automatically. When water level is below 4.7 inch, it will automatically disconnect the power; when water level rises above 4.7 inch, the pump will start again. Cut off immediately when pump fails to pump water to prevent the coil from getting burned.
• 【Higher Base Plate】 The higher base plate assures the prevention of debris collection in the sump pit, thermal overload protection ensures the pump operates within spec for longer durability.
• 【Multi Outlet Size】Compatible with 1-1/4" and 1-1/2" hoses. Three fittings with different diameters for outflow(1” ,1.25”, 1.5”) to choose from according to the flow rate.
• 【Do A Great Job】 400 Watt, 1/2 horsepower motor. Max Lift: 16 Feet; 2115 Gallon Per Hour rating tackles any draining job at a fraction of the time. This pump easily passes solids up to 1/2" in diameter. GREAT for flooded area, swimming pools, cellars or garden pond
• 【No maintenance needed】 Thermoplastic composite material is highly rugged. Designed and manufactured in line with the valid safety requirements. Thermoplastic body resists corrosion as there are not exposed metal parts. Lower noise and emergy-efficient. Oil free motor requires no maintenance.

User questions & answers

Question:	I need pump out my jacuzzi that has between 500 and 700 gallons. Would this be sufficient for that
Answer:	Yes I pumped out my inground pool with it
Question:	why does the pump motor start and stop when i turn the float switch one way or the other
Answer:	It’s supposed to do that, the float is the on and off switch.
Question:	Can this be powered by my vehicle using an inverter
Answer:	That should be possible, assuming that you have an inverter or a large enough size. The pump claims a 400W motor, but when considering motor inrush current and such, I would suggest one at least 600 watts continuous or more.
Question:	what’s the blue side attachment in the picture
Answer:	The blue side attachment is a float to stop the pump when the water is gone

Product description

FEATURES:

1.115V/60Hz,1HP powerful heavy duty copper wire motor,max capacity of flow rate 3435GPH. Max depth for pump working under water is 23FT. Max particle size is 1 INCH. Max water temperature is 35℃ and max ambient temperature is 40℃. Build-in overload thermal protector with automatic reset which means this pump can rework after cooling down for a while.



2.Our pump has a float switch which means pump can switch on or off automatically. When water level reach more than approximate 21.65 inch from bottom in water,the pump will start to work automatically and when water level goes down below approximate 9.45inch,the pump will switch off. If you want to continue pumping water,you can hold up float. Once water level down below the hole of pump bottom and cannot pump water out any more,you should put float switch down or pull out the plug,otherwise pump motor will burn out. The minimum water level what this pump can leave is 1.56 inch.



3.Please note that this pump is not suitable for 24hours continuous running such as powering garden water features or fountains as other sellers may imply. For the first time use,you should submerge pump inclined downward in water to discharge air completely.



4.The pump is widely usefor flooded area,swimming pool,garden pond and so on. Able to drain infiltrating water,cesspools or reservoirs,decanting water and clean,dirty or muddy swimming pools. It is a necessity for a house and you will never worry the basement flood again.



SPECIFICATION:

Stainless Steel Housing

Voltage/Frequency: 115V/60Hz

Horsepower: 1HP

Max Flow Rate: 3435GPH

Max Supply Height: 24FT

Max Submersible Depth: 23FT

Max Particle Size: 1 INCH

Power Cord Length: 25FT



PACKAGE CONTENT:

1x submersible pump

1x outlet connector

1x user manual

• Submersible pump for clean/dirty water with UL Plug and copper wire motor
• Voltage: 115V-60Hz ;Power: 1HP
• Max Flow Rate: 3435GPH;Max Delivery Height: 24FT ;Cord Length: 25FT
• Build-in overload thermal protector with automatic reset. Each pump has a float switch
• Discharge Fittings: 1" & 1-1/4" & 1-1/2". Not designed for continuous running.

User questions & answers

Question:	I have a 10x10x10 hole i need the pump to fit in. Will it fit and can it run for up to 10 hours. We have pretty long hard rainstorms
Answer:	The box it came in is 9x7 unit is 14” tall, only had to run mine for 8 hours so don’t know about 10 hours
Question:	What size is this pump
Answer:	its about a foot tall and 7 or 8 inches across. I drained my pool and it worked well. i got an actual rate of about 600 gph
Question:	Can someone please help me? i have the pump in 30” of water in a koi pond. i turn it on when we have company. it won’t turn on & trips gfi. help
Answer:	If it trips the GFCI, then take it out of service immediztely. If you are using an extension cord with it, e sure the connection is not laying in water, or is wet.
Question:	What is the outside diameter of this pump
Answer:	The top and bottom black plastic parts are 6 1/4". The stainless steel body is 5 1/2". This pump is very well made, and the cord is extra long.

Product description

FEATURES:

1.115V/60Hz,1.5HP powerful heavy duty copper wire motor,max capacity of flow rate 4250GPH. Max depth for pump working under water is 23FT. Max paricle size is 1 INCH. Max water temperature is 35℃ and max ambient temperature is 40℃. Build-in overload thermal protector with automatic reset which means this pump can rework after cooling down for a while.



2.Fully stainless steel pump body and pump bottom which will be not easy to rust and not easy to be broken,then can use the pump longer. Also the stainless steel body is easy to clean.



3.When water level reach more than approximate 21.65 inch from bottom in water,the pump will start to work automatically and when water level goes down below approximate 9.45 inch,the pump will switch off. If you want to continue pumping water,you can hold up float. Once water level down below the hole of pump bottom and cannot pump water out any more,you should put float switch down or pull out the plug,otherwise pump motor will burn out. The minimum water level what this pump can leave is 1.96 inch.



4.Please note that this pump is not suitable for 24hours continuous running such as powering garden water features or fountains as other sellers may imply. For the first time use,you should submerge pump inclined downward in water to discharge air completely.



5.The pump is widely usefor flooded area,swimming pool,garden pond and so on. Able to drain infiltrating water,cesspools or reservoirs,decanting water and clean,dirty or muddy swimming pools. It is a necessity for a house and you will never worry the basement flood again.



SPECIFICATION:

Stainless Steel Housing and S.S. Pump Bottom

Voltage/Frequency: 115V/60Hz

Horsepower: 1.5HP

Max Flow Rate: 4250GPH

Max Supply Height: 32.8FT

Max Submersible Depth: 23FT

Max Particle Size: 1 INCH

Power Cord Length: 25FT



PACKAGE CONTENT:

1x submersible pump

1x outlet connector

1x user manual

• Fully Stainless Steel Submersible pump for clean/dirty water with UL Plug and Copper wire motor
• Voltage: 115V-60Hz ;Power: 1.5HP
• Max Flow Rate: 4250 GPH;Max Delivery Height: 32.8FT ;Cord Length: 25FT
• Build-in overload thermal protector with automatic reset. Each pump has a float switch
• Discharge Fittings: 1" & 1-1/4" & 1-1/2". Not designed for continuous running.

User questions & answers

Question:	Can you connect a 1-1/2” npt fitting and pipe at discharge
Answer:	Yes
Question:	What is the diameter of the pump I have a 5 and a 1/2 inch opening
Answer:	The diameter of the pump is around 6.25inch.
Question:	is it us gallon or imperial gallon
Answer:	It is US gallon.
Question:	What is the warranty on this pump
Answer:	I don’t know but I have been using for over a year with no problems

Product description

Prostormer water pump is featured by a durable thermoplastic housing, max lift of 26 feet and max delivery rate 3700GPH, this submersible pump is ideal

for draining water from flooded basements, water wells, garages, garden pond.  Also great for pool changing work with its 16.5-feet heavy-duty power cord.

Specifications:

Voltage: 120V~60Hz

Power: 1HP

Delivery Rate Max.: 3700GHP

Delivery Height Max.:26Ft

Immersion Depth Max.: 23Ft

Power Cord Length:16.5 feet

Weight: 7.2Lbs

Diameter of Pipe: 1",1-1/4",1-1/2" (From Up to Down)

Applications: Garden, Yard,Swimming pool, Pond, Flooded area

• ⚡⚡PROSTORMER SUBMERSIBLE WATER SUMP PUMP⚡⚡
• 🔥【Good Drainage Effect】Suitable for Pool, Pond, Garden, Flooded Cellar, Aquarium, Irrigation and other places.
• 🔥【1HP High Power】Prostormer Sump Pump uses 1HP power, which is more efficient than ordinary 3/4HP sump pump; Max 3700 Gallon Per Hour rating tackles any draining job at a fraction of the time.
• 🔥【Multi Outlet Sizes】3 different diameters outlets (1 inch ,1-1/4 inch, 1-1/2 inch) to adapte for different size hoses as needed according to the flow rate. The bigger the flow is, the wider the outlet should be.
• 🔥【Keep Open Mode】When you put the float switch locked on the sump pump, the sump pump will keep working all the time. Once the pump can not pump any water, you should cut off the power immediately to prevent the coil from getting burned.
• 🔥【Automatic ON/OFF Mode】The float switch should be unlocked from the pump. When the water level rises above the pump, the pump will start working automatically under the control of float switch. When the pump fails to pump water, it will automatically disconnected the power.
• 🔥【Sealing Structure & Durable Construction】The sump pump features a durable sealing structure and the durable thermoplastic body keeps the pump from corrosion. The higher base plate which assures the prevention of debris collection in the sump pit.

User questions & answers

Question:	what kind of warranty does it have
Answer:	PROSTORMER 1HP Submersible Sump Pump provides free replacement service within one year.
Question:	Can i leave this on the vinyl lined pool stairs all winter and have it automatically lower water after lots of rain
Answer:	It is recommended that you store the Prostormer sump pump when it is not in use to avoid damage.
Question:	What is the watts
Answer:	about 700 watts

Product features

Multi Outlet Sizes

3 different diameters outlets (1 inch ,1-1/4 inch, 1-1/2 inch) to adapte for different size hoses as needed according to the flow rate. The bigger the flow is, the wider the outlet should be.

Automatic Float Switch

When the float switch is unlocked from the pump, if the pump fails to pump water, it will aotomatically disconnect the power. If the water level is higher than the pump, the pump will start again.

Keep Open Mode

When you put the float switch locked on the sump pump, the sump pump will keep working all the time. Once the pump can not pump any water, you should cut off the power immediately to prevent the coil from getting burned.

Higher Base Plate

The pump has a higher base plate which assures the prevention of debris collection in the sump pit.

Product description

1/2 hp, submersible, non-clogging, vortex design utility pump, pumps up to 2500 gph at 0', corrosion resistant reinforced thermoplastic housing, volute & impeller, bottom suction design filters debris & removes water down to 1/4 inch of surface, passes up to 1/2 inch solids, 1 1/4 inch nps high volume discharge with 3/4 inch Garden hose Adapter, easy access handle for portability. This product is assembled in the USA.Easy installation and easy handling.

The Wayne 1/2 HP 1680 GPH submersible utility water pump can handle material up to 1/2-inch thick without getting clogged. It can pump out 2600 gallons per hour, with a bottom suction that takes out water to within an eighth of an inch of the surface. Glass reinforced thermoplastic for the housing, volute, and impeller prevents rust, the 3/4-inch adjustable discharge adapter easily connects to garden hoses, and an easy-access handle provides complete portability. Wayne backs its pump with a one-year limited warranty.

• 1/2-horsepower submersible utility water pump can handle material up to 1/2-inch thick without clogging
• Removes water within 1/8-inch of surface
• Glass reinforced housing prevents rust
• Connects to garden hose with 3/4-inch adjustable discharge adapter
• 1-year limited warranty.Requires 2 5/8 inch of water to prime

User questions & answers

Question:	What is the PSI of this pump? ...Or what height does it pump up water? I don't see that spec
Answer:	I have re-read the documentation that accompanies the pump and nowhere does it state PSI or head (height) capability. My experience with draining a 500 gallon holding tank: discharge is not high pressure, less than a hose connected to the house; it will pump at least an 8' head. The pump did not deliver 2500 gph.
Question:	Anyone use this for dirty water and how did it handle it? Did the debris pass thorough or clog it
Answer:	The first thing is what you mean by "dirty", that's the problem. I have used this pump for very dirty water full of leaves, branches, and muck and it definitely clogs without the modifications I describe following. The main thing that restricts what passes through this pump is the size on the intake port on the bottom of the pump which is only a little over an inch. The port has to be kept small to maintain the vortex inside the lower bell of the pump. It is the vortex that moves the water, not the impeller like other pumps! This means that if you have a lot of small particles, it is possible for a clog to occur at the elbow at the output port shown in the picture. More likely, however, the clog will occur at the smaller intake port. Generally speaking, anything that can make it through the intake port will exit if there is not some restriction at the output port. This means, for maximum dirty water flow, you have to do two things. First, swap out the provided elbow meant for connecting a garden hose, and attach a system of standard 1 1/4" pvc pipe from your local hardware store. If you want to connect to a hose, use an adapter at the end of the pvc pipe (or better yet, use a flexible large diameter discharge hose sold on Amazon). The second thing you need to do is prevent objects larger than the intake port on the bottom of the pipe from trying to enter the pump (such as leaves, etc.) To do this, place a metal 1/4" or 1/2" metal screen across the bottom of the pump held in place with duct tape. Then, ideally, place a couple of 1/2" or so stick at the bottom to prevent the pump from sitting on the bottom of whatever you are pumping out. If you do both these thing, this pump is fantastic and can move a lot of water at impressive pressure for an immersible pump of it's size! Worse case, the attached bottom screen will clog and then you just have to lift the pump and sweep your hand across the bottom to remove the debris. If not do not do both of things I have mentioned, it will clog very easily due to the small intake port and if you use the restrictive elbow provided! I have used many different kinds of pumps of all types and this is best consumer type dirty water pump I have used but you need to make the modifications that I have mentioned which are very simple and cheap. I can try and post a picture of my modifications.
Question:	Do I need a garden hose attachment or does it come with one ? Also, if there isn't a float, what kind and where do I get one? Thanks
Answer:	It comes with 3/4-inch adjustable discharge adapter and connects to garden hoses. I unscrewed the 3/4 " adapter to fasten a pvc adapter on my pump so I was able to use 1 1/4 " corogated plastic hose when pumping water off my pool cover. It works faster with the larger plastic hose. Sorry I do not have any info about floats.
Question:	What is the lift
Answer:	Lift is how far ABOVE the pump it will pump liquid. example: 10 ft. lift means it will pump liquid 10 ft. above the level of the pump. Normally the higher the lift, the lower amount it will pump.

Product description

Features:



- 1 HP 750W submersible dirty clean water pump, with float switch and 25ft power cord, to help move dirty water away, for household or utility use

- Powerful Pump - Powered by a 1 HP oil-cooled electric motor for draining 3434 gallon per hour quickly

- Safe Use - Built-in automatic power shut off mechanism by auto float switch for preventing the coil from getting burned when pump fails to pump water

- Durability - Engineered Resin Construction for long serving time under water

- Wide Application - Great for household or utility use, such as swimming pools, cellars, garden pond or flooded road



Specifications:



- Overall Dimension(LxWxH): 6 9/16" x 6 1/4" x 14 3/8" (16.7 x 15.8 x 36.5 cm)

- Power Supply: 115V/60Hz/750W (1HP)

- Cable length: 24 11/12 ft (760 cm)

- Q.Max: 3434 gph (13000L/H)

- H.Max: 26 1/4 ft (800 cm)

- Max Submersible Depth: 23 ft (700 cm)

- Diameter of Hose: 1", G1", 1 1/4", G1 1/2" (From Up to Down)

- Max Drainage Temperature: 35ºC

- Max Particle Size: 1 3/8" (3.5 cm)

- Material: PP Plastic, Copper Wire



Package Contents:



- 1x Water Pump

- 1x Manual

• UL CERTIFICATION: 1 HP 750W submersible dirty clean water pump with float switch and 25ft power cord, a safe standard for Swimming Pool Pumps, Fountain Pump, Filters etc. Buy our Sump Pump with Confidence to help move dirty water away, for household or utility use
• SAFE USE: Built-in automatic power shut off mechanism by auto float switch for preventing the coil from getting burned when pump fails to pump water
• DURABLE & STURDY: Heavy duty engineered Resin Construction for long serving time under water, can prolong this submersible pumps life expectancy
• 1 HP WATER PUMP: Powered by a durable oil-cooled electric motor,runs, H.Max: 26 1/4ft, draining 3434 gallon per hour quickly
• WIDE APPLICATION: Ideal for handling such tasks as draining water from a basement or a shallow flooded area, draining or refilling your swimming pool, pond or simply a bath tub, great for household or utility use, such as swimming pools, cellars, garden pond or flooded road

User questions & answers

Question:	How long is the electric cord and what size hose pipe can you use
Answer:	Dear customer, the electric cord length is 25ft, it can fit these hose pipes: 1",G1",1-1/4",G1-1/2"(From Up to Down).
Question:	How many gallons of water does this pump move per hour
Answer:	Not sure but it removes about a foot per hour in my standard built in pool
Question:	What size tubing should I buy to use with this
Answer:	The diameter of pipe can be 1", G1", 1-1/4", G1-1/2" (From Up to Down). You can select one size based on your preference.
Question:	Anyone have a copy of the manual? I can't find it online. Trying to finally close the pool and it won't start for some reason
Answer:	I can't figure out how to copy pictures into this section. And the instructions aren't that good - the english used has incorrect grammar so take that into consideration as well. So I'll type what I think you may need to know. Before using the pump again, first "soak" it so that any possible dirt residues do not block the appliance. Submerge pump at an angle into the liquid so that no air pocket forms on the underside of the appliance. Suction would be prevented by this. Once the pump is submerged, it can be righted again. It also says that we should be using a rope to lower it into the water and not using the main cable..... Minor faults are often sufficient to cause a malfunction.... Pump does not run ----check cables, plug, socket and fuse. Motor defective? contact service partner. Automatic power-off low water level float - manual vertical float motor normal power, start the pump without water, will damage the water pump, manual vertical float when use must be care (I typed this as manual listed it, bad/incorrect grammar, makes no sense) Cleaning the suction area - clean all accessible insides of the casing. Remove fibers which have wound around the rotor shaft by opening the pressure connection. Remove stubborn contamination with a brush and detergent. It also says to if you unable to correct a fault yourself, please contact our technical support directly. BUT there is no number listed anywhere in the 8 page manual. Sorry! This is all the manual says. Not a good manual...

Product features

Yescom 1 HP Submersible Water Pump

Our submersible pool pump features powerful, high efficiency, sturdy construction, lower maintenance costs and works quietly. Ideal for handling such tasks as draining water from a basement or a shallow flooded area, draining or refilling your swimming pool, pond or simply a bath tub.

At Yescom, we strive to provide our customers with great products.

Durable Material

• Sturdy and Solid construction
• UL Safety

Great Powerful Sump Pump

• Power Supply: 115V/60Hz/750W (1HP)
• Heavy duty motor runs underwater about 23ft，empties and fills your pond with ease

Quiet pond pump

• Very silent and quiet, you can't hear the motor run if you’re 10 or 15 feet away

Product description

Our ADX line of pumps features a new and game-changing water sensor ON/OFF, there's no need for a float switch anymore with this design.

Never worry again about the flooding or about the pump working dry and damaging the motor. After 1 -3 minutes of the sensor being dry, the pump will turn itself off automatically to prevent jamming and pump some remaining water..

This is our dirty water model with this system, it can pump up to 26ft and a maximum of 81 gpm. 110v/1.5hp.

It's suitable for use in reduced spaces, it offers exceptional power in a small, durable frame and it can easily fit inside small openings of 10 inch diameter or larger. Designed to drain standing water from any environment, it's ideal for flooded basements, farm use, draining standing water from swimming pools, fountains, typical residential or commercial water transfer applications.

Dimensions 6.5"D x 7.5"W x 14"H

Warning: This pump is designed to be used with a lay-flat hose and the adapter included features connections for only that type of hose. A regular garden hose is not recommended for this model.

• Dirty water sump pump.
• New water sensor technology replaces old float switch systems making it fully automatic.
• 4 adjustable start and stop positions for the sensor, when the sensor gets wet it starts the pump, when it gets dry it stops it.
• High quality stainless steel casing. Pumps Starts Automatically between 7.5 & 11 inches.
• 2 year warranty with us directly.

User questions & answers

Question:	Does this pump have to be in a sump or can it sit on a basement floor
Answer:	Hi, no, this model that's not have a check valve, regards - Oscar PREMIUMPUMPSUSA
Question:	this pump died
Answer:	Hello, I do not see these specifications in the manual. The only thing I read concerning temperatures was to clean and store unit during frost conditions. I live in FL, so frost is not a real concern for me. As I mentioned in my review, the manual is not very good.
Question:	How low does it pump before it shuts off. Can you turn the water sensor off
Answer:	Hi! Yes, Palestine is labeled.
Question:	Would it fit inside an 8” pvc pipe? (vertical pipe with the pump on the bottom). it would be under ground (inside the pvc pipe) about 15 feet
Answer:	Hi there, we've been using a cotton/polyester blend for the last few years, but actually just switched to a 100% polyester variety because of how well it has been performing for us! So as we transition into this new material you may receive one or the other, but if you're reading this more than a few weeks later you will likely get a poly version.

Product description

Features: - Compatible with Flat PVC Hose in 0.98’’ and 1.26’’ inches - Screw Thread in NPT1-1/4’’and NPT5/8’’ - Auto Float Switch: Start/Stop Automatically - Rugged and High-Quality Materials - Designed and Manufactures with Valid Safety Requirements - Lower Noise and Energy-Efficient - Oil-Free Motor, Requires no Maintenance - Thermoplastic Body Resists Corrosion - Great to Drain the Dirty Water from the Pond, Garden Pond, or Water Tanks - Perfect for Household & Utility Applications of Transferring Water from One place to Another What's in the Box: - Water Pump - Power Adapters Technical Specs: - Power Supply: 400W (0.5HP) - Construction Material: Engineered ABS and Metal - Power Output: AC 110V 60Hz - Qmax: 1,980 gallon/H (7,500L/H ) - H.Max: 26.25ft. (8 Meters) - Power Cord Length: 16 feet - Type: Water Pump (blue) - Diameter of Pipe: Screw thread in NPT1-1/4” & NPT5/8”. Flat PVC Hose in 0.98’’ and 1.26’’ inches - Applications: Garden, Yard, Swimming pool, Pond, Flooded Area - Product Dimension (L x W x H): 6.2’’ X 6.1’’ 12.4’’ –inches

• POWERFUL SUCTION: This 400W powerful sump pump submersible has a Qmax of up to 1,980 gallons per hour (7,500L/H) and H.Max of up to 26.25ft. (8 Meters) and can easily tackle any draining job in just a short period of time
• RESISTS CORROSION: The basement sump pump submersible is made with heavy-duty engineered ABS and metal construction material and it features a highly rugged thermoplastic body that resists corrosion to withstand years of repeated use
• MULTI SIZE OUTLET: SereneLife water pump is compatible w/ flat PVC hose in 0.98" & 1.26" inches & it is equipped w/ screw thread in NPT1-1/4" and NPT5/8". Perfect for household & utility applications of transferring water from one place to another
• AUTO FLOAT SWITCH: This submersible pump with float is designed & manufactured w/ valid safety requirements. Features sump pump float switch that automatically starts/stop the pump and can be set by adjusting the float switch in its latching holder
• VERSATILE APPLICATION: Has a lower noise operation and highly energy-efficient. Features an oil-free motor and requires no maintenance. Great for draining the dirty water from the swimming pool, basement flood, tub, garden pond, or water tanks

User questions & answers

Question:	What size check valve and where to buy
Answer:	The thermal overload protection is a last line of defense to protect the motor and prevent a fire if the pump runs dry, or locks up due to something getting stuck in the impeller. It is not meant to routinely turn the pump on and off. For that application you should use a sump pump with a built-in float switch.