12 best mill lathe drill combo

Product description

The Mill/Drill Head PF 230 converts your Lathe PD 250/E into a machining center. The Mill/Drill Head PF 230 comes with a column size 1 3/8" x 15 3/4" (35 x 400mm) including the necessary mounting bracket and bolts to attach it to the Lathe PD 250/E. The lathe's top slide is then replaced with the table (supplied with the Mill/Drill Head PF 230). The table has a size of 4 5/16" x 2 3/4" (110 x 70mm) and 3-T slots 15/32" x 15/64" x 15/64" (12 x 6 x 6mm). The lathe now functions as a compound table, with X-Y travel being longitudinal and cross-wise respectively. Three collets of sizes 15/64" - 5/16" and 25/64" (6, 8, 10mm) are included. Technical data: 110 - 120V, 60Hz, 140W (0.1877hp), speeds 280 - 550 - 870 - 1,200 - 1,500 and 2,200rpm. Note: Lathe not included.

From the Manufacturer

Proxxon mill/drill head PF230 converts your 34004 proxxon lathe into a machining center. The mill/drill head PF230 comes with a column size 1-3/8-Inch by 15-3/4-Inch (35 by 400mm) including the necessary mounting bracket and bolts to attach it to the lathe PD230/E, number 34004. The lathes top slide is then replaced with the table (supplied with the mill/drill head PF230). The table has a size of 4-5/16-Inch by 2-3/4-Inch (110 by 700mm) and 3 T-slots 15/32-Inch by 15/64-Inch by 15/64-Inch (12 by 6 by 6mm). The lathe now functions as a compound table, with X-Y travel being longitudinal and cross-wise respectively. Three collets of sizes 15/64-Inch, 5/16-Inch and 25/64-Inch are included.

• Precision proxxon engineering for top quality machinery
• 110 - 120V, 60Hz, 140W (0.1877hp), speeds 280 - 550 - 870 - 1,200 - 1,500 and 2,200rpm
• The lathe functions as a compound table, with X-Y travel being longitudinal and cross-wise respectively
• Three collets of sizes 15/64" - 5/16" and 25/64" (6, 8, 10mm) are included.

User questions & answers

Question:	will this machine mill horizontically while indexing vertically? like cutting a spiral pieces
Answer:	No idea about glue, I would just buy another one because the glue might not last
Question:	Hi this is machine 110 volt or 220 volt
Answer:	Not common...or mine, which seems superbly built, is an aberration...
Question:	There are no tolerances shown. Can you please provide them
Answer:	I’m inclined to think they are replaceable because each blade is attached to the handle with 2 Phillips screws. I gave not attempted to find replacement blades.
Question:	Is This a whole milling machine
Answer:	Yes 2 foil cutters, 1 black and 1 white

• The table is suitable for Mini Drill and drill bracket series. It can also apply to other suitable machine.
• The work table is composed of several adjustable dovetail slotaluminum alloy composition, can guarantee the minimumspace and ensure the accuracy
• The working table comes with three T shaped groove, standard size is 15x8x6mm.
• X axis travel : 200mm,Y axis travel : 50mm, Distance between grooves : 34mm
• Working table size : 310mmx90mm, Height : 80mm (including two working clamp)

User questions & answers

Question:	Is this good enough to mill a polymer 80 percent lower
Answer:	Absolutely! I used carbide cutters and got really great results.
Question:	Will this fit on a Proxxon MF
Answer:	My lathe did not come with tools or gears, the basic metric tool will work the key for spindle head, you can use an old socket tool and grind to fit
Question:	Does this read in inches
Answer:	yes,this mini power motor lathe tool kit can process metals,turning tool is high - speed steel material, can process soft, non - ferrous, precious metals,ect
Question:	Will this fit on a dremel
Answer:	You can search the CNC parts that you want to buy in our shop Jectse us, or send a picture of the product to us by email, we will help you to find this product.

Product features

Miniature precision multifunction Milling Machine Bench drill Vise Fixture worktable X Y-axis adjustment Coordinate table

Type : BG6300 working table

T solt : have three t solts

Solt size: 15mmx8mmx6mm

Mounting hole distance : two holes 93mm away from the nearest is the middle is 98mm,the distance is 112mm

Zero adjustment handwheel rotates a circle : 1.25mm.one lattice equal is 0.05mm

Apple to : Mini drill and drill bracket series and other suitable machine

Product description

Top Quality M2 HSS



Drill accurate center holes in material prior to turning, or use as a starter bit for accurate holes in stock. Sizes 1, 2, 3, 4 and 5, 60° tip angles.

• Top Quality M2 HSS
• Drill accurate center holes in material prior to turning, or use as a starter bit for accurate holes
• Sizes 1, 2, 3, 4 and 5, 60° tip angles.

User questions & answers

Question:	do the numbers on the bits correspond to numbered drill sizes
Answer:	Nope. They are numbered #1-#5 No imperial or metric sizing is indicated
Question:	Are these made to fit in standard R8 collets
Answer:	I would use them in a drill chuck to save time , as long as they run true a collet is not needed. They are designed to put a starting point for a drill bit.
Question:	Are these good for drilling steel and iron metals or would they not hold up
Answer:	Yes. They are good for drilling metal. My are holding up well.
Question:	Where is this product made
Answer:	Nothing about where they are made on the label, and only "HSS #1 -#5 on the tools themselves. But they work great in my lathe or drill press.

Product description

The unit is supplied with a stable base of cast iron. Both vertical column and compound table are of treated, high quality aluminum. All axes are play-free and have adjustable slides. The headstock, made of die-cast aluminum, houses the 24 pole balanced special motor and provides stability even at high operating speeds. This stability facilitates the use of the finest cutters. Six triple slit, hardened MICROMOT steel collets come with the machine and cover shank sizes of 1/32", 1/16", 5/64", 3/32", 7/64" and 1/8" (1.0, 1.5, 2.0, 2.35, 3.0, 3.2mm). The table is fitted with three T-slots of the 15/32" x 15/64" x 13/64" (12 x 6 x 5mm) MICROMOT-norm. An adjustable ruler scale eases the positioning of the work piece. All hand wheels are zero adjustable with 1 revolution = 1/32" (1.0mm), 1 division = .002" (0.05mm). Technical data: Speed 5,000 - 20,000rpm; Table Size 7 7/8" x 2 3/4" (200 x 70mm); X-Y Travel 5 17/64" and 1 13/16" (134 and 46mm); Vertical Travel 2 3/4" (70mm); Footprint Size 5 7/64" x 8 55/64" (130 x 225mm) Height 13 25/64" (340mm); Max. Power 1/8hp (100W); Volts 110 - 120V AC, 60Hz; Weight 15.5 lb (7kg)

Proxxon micro mill MF 70 - This small and beautiful unit is ideal - the accurate mill for lab, optician, jewelry, electronic and model building projects. Mill is made with a cast iron base. The vertical column and compound lathe are treated, high quality aluminum. All axes are play-free and have adjustable slides. The headstock, made of die cast aluminum, houses 24 pole balanced special motor and provides stability even at high operating speeds. This stability facilitates the use of the finest cutters. Comes with 6 triple slit hardened steel collets 1/32-Inch, 1/16-Inch, 5/64-Inch, 3/32-Inch, 7/64-Inch and 1/8-Inch (1.0, 1.5, 2.0, 2.35, 3.0 and 3.2mm) table has three T-slots and an adjustable ruler scale which eases the positioning of work-piece. All hand wheels are zero adjustable with one revolution equals 3/64-Inch (1.0mm) 1 division equals .002-Inch (0.05mm).

From the Manufacturer

Proxxon micro mill MF 70 - This small and beautiful unit is ideal - the accurate mill for lab, optician, jewelry, electronic and model building projects. Mill is made with a cast iron base. The vertical column and compound lathe are treated, high quality aluminum.

• Quiet, precise and vibration-free for fatigue free use
• Low weight and slim design, without ever compromising performance
• High quality precision tools

User questions & answers

Question:	Is it programmable
Answer:	I really don't remember if the clamps came with it or not. It did come with the complete set of collets and wrenches. I have 2 sets of clamps so maybe one set came with it, I know I had to buy the little milling vise, and a drill chuck. Everything for this machine is pretty expensive but first quality. I have a bigger milling machine now, and I will be selling my MF70, but only because it was too small for the bigger steam engines I am building.
Question:	Does the MF70 ship from Amazon with clamps to hold the work to the table
Answer:	Mine says "Made in EU"
Question:	Is this a Chinese made machine? Another website says it is from Luxembourg
Answer:	I don't think it would --the chuck will not let you get a big enough milling bit into it
Question:	Would this machine be adequate for milling AR-15 lower receivers
Answer:	5pcs/Set M3 M4 M5 M6 M8 HSS counterbore for socket head cap screws all 5 different sizes and came in separate plastic tubes used mine on aluminum worked fine

Product features

Proxxon 37110 Micro Mill MF 70

The Proxxon micro mill MF 70 does intricate and detailed tasks with ease. From lab work to tasks for opticians, jewelry and model building projects, this tool is a boon! This precision mill is easy to work with as it can be placed in a tabletop. Adjustable, portable and simple to operate, this mill makes all detailed projects hassle-free.

Stable and Adjustable

You will be able to position the mill according to the task with ease as it is engineered to provide stability at high operating speeds. Combine the ultimate utility and precision with the Proxxon 37110 Micro Mill MF 70.

Product description

Features:

Machine tool with powerful motor, the motor box and spindle box for conjoined structure. Main parts: such as the spindle box, tailstock, long stand, size slider, motor blade, gear, connecting block are made of metal materials, with belt protection cover. Center height is 75mm and distance between centers is 135mm, motor speed normally drops to 2000rpm when using the lathe to machine metal. Maximum motor power is 60W by using more powerful motor. Turning tool is high - speed steel material, can process soft, non - ferrous, precious metals. By using central block, the diameter can be expanded to 50mm.

Specification:

Condition: 100% brand new

Metal: Metal

Weight: 4990g/176oz

Motor Speed: 12000rpm

Input Voltage/Current/Power: 12V DC/5A/60W

X-Axis travel: 32mm

Z-Axis travel: 145mm

Max Diameter of Machined Material: 100mm

Length of Machined Material: 135mm

Machining Accuracy: 0.07mm



Package Includes:

1 x Mini Lathe

1 x Adapter 

1 x Power Cord

1 x Accessory Package

1 x Machine Bottom Plate

1 x User Manual

• Machine tool with powerful motor, the motor box and spindle box for conjoined structure.
• Main parts: such as the spindle box, tailstock, long stand, size slider, motor blade, gear, connecting block are made of metal materials, with belt protection cover.
• Center height is 75mm and distance between centers is 135mm, motor speed normally drops to 2000rpm when using the lathe to machine metal.
• Maximum motor power is 60W by using more powerful motor.
• Turning tool is high - speed steel material, can process soft, non - ferrous, precious metals. By using central block, the diameter can be expanded to 50mm.

User questions & answers

Question:	is good for metal
Answer:	The existing tool is .164 square by ~ 2" long. It can be reshaped with a grinding wheel. There wasn't a extra tool order form with the unit. There are cutter sets available from Grizzley and Harbor Freight Tools, but I have not ordered yet
Question:	Where can you buy the parts for the converted over to cnc thanks in advance
Answer:	It has a pass through hole but only 6mm
Question:	can this lathe process titanium, brass, tungsten, damascus steel etc
Answer:	8X8mm
Question:	does it come with any metal cutting tools
Answer:	120v

Product description

Parameters:



Maximum workpiece turning diameter of the machine: 125mm



Maximum length of the piece: 180 mm



Maximum workpiece turning diameter on the tool holder: 60mm



Spindle through the hole diameter: 9mm



Spindle cone: MT.1



Number of treated metric threads: 8



Metric thread processing range: 0.4-1.5mm



Number of treated wires: 8



Inch thread range processing: 0.0028-0.0055 1 / n "



Longitudinal feed level: 2



Longitudinal feed for spindle mandrel: 0.07-0.14 mm



Tailstock travel: 18mm



Tailstock cone: MT.1



Spindle speed range: 560-2500 rpm Level 5



Maximum drilling diameter: 6 mm



Distance from the end face of the spindle to the work surface: 120-180 millimeters



Distance from central spindle to column area: 125 mm



Drilling and milling head rotation angle: 360 °



Spindle speed range: 500-2500 rpm 10 levels



Drilling and milling vertical lifting head stroke: 60 mm



Working surface width: 60mm



T-slot work bench width: 8mm



Working surface length: 85mm



Spindle sleeve movement quantity: 40mm

• Maximum workpiece turning diameter of the machine: 125mm
• Maximum length of the piece: 180 mm
• Maximum workpiece turning diameter on the tool holder: 60mm
• Spindle through the hole diameter: 9mm
• Spindle cone: MT.1

Product description

This M1111 Milling Machine has all of the important features of the M1110, but with a few extra time-saving luxuries. However, this mill is further fortified with a quick-tilt headstock for horizontal milling, 1 HP brushless motor, a multi-function digital depth scale on the quill, push-button speed control and digital spindle tachometer. The quick reversing tapping feature also makes hole threading simple. Just put the machine in tapping mode, start the tap, and when the thread is completed, push the button at the end of the rack levers and the spindle reverses, immediately withdrawing the tap from the hole. The back-lit digital tachometer tells you the precise spindle speed for matching tooling and material. All of these extra features make the M1111 Milling Machine one of the most sought after machines available! Made in an ISO 9001 factory.

• 1HP, 220v, Brushless DC Motor w/ Step-Up Transformer, 110v Operation
• Push button motor control for forward, reverse, tapping and off
• Variable Speed: 100 - 1750 RPM
• R-8 Spindle Taper
• Over 14" Headstock Movement

User questions & answers

Question:	I'm not trying to nit-pick: one pic has z (vertical) dial or crank on the left-the other one has it on the right. Which is it
Answer:	55 mm
Question:	does the spindle have power feed
Answer:	Yes it should, inside diameter of the clamp is 55mm
Question:	Can I plug it into an standard 110 Volts outlet
Answer:	Hello Betty the hole size is 2 and 7/8 We had to put them on for insurance reasons."only when the inspector shows up" Take care .Jim
Question:	how well can it mill steel? is it too light duty to be useful for mild steel
Answer:	This drill press uses a 60 watt bulb. The light socket included is for 110 volt use only. If the socket is used while operating at 220 volt the light bulb will explode, potentially causing serious personal injury.

Product features

Shop Fox M1111 Deluxe Milling Machine

This M1111 Milling Machine has all of the important features of the M1110, but with a few extra time-saving luxuries. However, this mill is further fortified with a quick-tilt headstock for horizontal milling, 1 HP brushless motor, a multi-function digital depth scale on the quill, push-button speed control and digital spindle tachometer. The back-lit digital tachometer tells you the precise spindle speed for matching tooling and material. All of these extra features make the M1111 Milling Machine one of the most sought after machines available.

Surface Ground Cast-Iron Table

This machine has a precision-ground cast iron milling table that can travel 5-3/4 by 15-1/2 inches, along with a hand wheel and fully geared lift system that can raise and lower the headstock up to 14-3/4 inches. In addition, the headstock can tilt up to 90 degrees for horizontal milling.

Longitudinal Feed

The longitudinal feed, or X-axis is moved by the handwheel at the end of the table. The handwheel easily moves the table in both directions side-to-side. One complete revolution of the handwheel moves the longitudinal feed 0.100 inch for precision adjustments. The scale included on the front of the table is for use when a tight tolerance is not required. The longitudinal feed can be locked in position by a table lock located on the front of the table.

Cross Feed

The cross feed or Y-axis is moved with the handwheel located on the front of the table base and operates in the same fashion as the longitudinal feed for precise front-to-back adjustments.

Digital Readout and Control Panel

The M1111 features a front-mounted emergency stop button, a see-through chip guard with a safety switch, and a quick-reversing tapping function which allows you to create threaded holes.

Tapping Mode

The quick reversing tapping feature also makes hole threading simple. Just put the machine in 'tapping mode', start the tap, and when the thread is completed, push the button at the end of the rack levers and the spindle reverses, immediately withdrawing the tap from the hole.

Brushless Motor and Variable Speeds

The Shop Fox M1111 mill contains a 1-horsepower, brushless DC motor and a push-button speed control that deliver variable speeds between 100 and 1,750 revolutions per minute (RPM). A back-lit digital spindle tachometer tells you the tool's precise spindle speed so that you can set it to just the right speed for your project.

Product description

The table is suitable for Mini Drill and drill bracket series.

It can also apply to other suitable machine.

The work table is composed of several adjustable dovetail slot aluminum alloy composition, can guarantee the minimum space and ensure the accuracy

Table size: 365 × 200 mm. Weight: 6.8 kg

X axis distance is 350 mm. Y axis distance is 100 mm.

Hand Wheel Scale Per Ring is 3 mm.



Package includes:

1 Pc of Milling table of Heavy Version

• The table is suitable for Mini Drill and drill bracket series. It can also apply to other suitable machine.
• It can also apply to other suitable machine. The work table is composed of several adjustable dovetail slot aluminum alloy composition, can guarantee the minimum space and ensure the accuracy.
• Table size: 365 × 200 mm. Weight: 6.8 kg
• X axis distance is 350 mm. Y axis distance is 100 mm. Hand Wheel Scale Per Ring is 3 mm.

User questions & answers

Question:	What is the actual X-axis travel distance for the heavy version
Answer:	3.0625" overall height (3 1/16")
Question:	Why does the medium model have more X &Y travel than the large model
Answer:	metal
Question:	What is the length and width of the cast iron base
Answer:	Thank you raising your concerns. The 2.5" milling vise is not included. You will need to purchase another 2.5" milling vise. What You Get: Milling Working Cross Table *1; Accessories box *1(hexagon wrench *1, standard fixture *1, M8 bolts and nuts *2); Manual *1. Any question, please don’t hesitate to let me know. Thank you for your attention to this product.
Question:	As this unit sits on a bench. What is the approximate height from the bench to the top of the table? Thanks
Answer:	I bought my clamps at harbor freight and Grainger supply

Product description

Remember when power tools were actually powerful? WEN’s 8-inch swing, 5-speed drill press is small but powerful enough to drill through metal, wood, plastics, and other materials. Max drill capacity is 1/2” in 1” thick cast iron. When you need accurate, repeatable holes, this tool will do the job more conveniently and precisely than a hand held drill. The perfect size for the shop and portable enough to take to the job. Constructed with a rigid frame consisting of cast iron: head, table, and base ensuring accurate holes. Its powerful induction motor features ball bearings for an extended life and it all comes together with smooth and balanced performance even at high speeds. The ½” chuck with JT33 spindle taper gives you versatility with a variety of bits. Worktable bevels 45° left and right for those tricky operations for the perfect right angles consistently. The base contains predrilled holes for mounting onto a bench or work stand. The slotted table allows for mounting clamps and vises for effective workholding. Since 1951, WEN has proudly produced innovative powered tools focused on value delivering meaningful features that will help you complete and enjoy the work as much as the project. Remember when you could drill holes in any material with ease? Remember WEN.

• Includes a 1/2-inch keyed chuck and onboard key storage
• Operates at 5 different speeds: 740, 1100, 1530, 2100, 3140 RPM
• Spindle travels up to 2 inches with easy to read, locking linear depth stops for accurate and repeatable drilling operations.Cord Length (ft.):6
• Durable 1/3 HP induction motor develops ample torque and power
• 6-1/2 x 6-1/2" worktable is height adjustable and bevels up to 45 degrees left & right
• Swing: 8 inch. Motor: 120V, 60Hz. Horsepower: 1/3 HP.

User questions & answers

Question:	ease of putting together
Answer:	It's really easy to put together. Just took me round 5-10 minutes.
Question:	What is the maximum width of material you are drilling (from drill center to hitting the pole
Answer:	i think the varied answers come from questions getting sent to people who have purchased different sizes. I noticed some of the reviews are also for other models. This item, the WEN 4208 has an 8-inch swing. So, you can drill the center of an 8- inch diameter object, or about 4- inches from drill center to body. The WEN 4210 & the WEN 4212 have 10- inch swings. Anyone trying to drill the center of a 9- inch wheel would need one of these models. This 4208 is a Great drill for the money. i like that the head can be swung over the edge of a work bench, which allows for drilling into long stock. Like into the bottom center of a 36" post. The beveling work table is another great feature & one i did not have on the press this will replace. If you have the space, consider the WEN 4214 with 12-Inch swing. it is still small enough to be bench top, but you can drill the center of 12- inch/ bowls & table tops.
Question:	Can you rotate the drill press on this unit 90 degrees, so that it hangs off the edge of the workbench, to drill into the ends of longer pieces of stock
Answer:	Yes you can, just be careful when ever you do this.
Question:	does it drill round holes
Answer:	I only drill square holes with mine.

Product features

Powerful. Versatile. Compact.

Remember when power tools were actually powerful? WEN’s 8-inch 5-Speed Drill Press is compact enough to limit space on your work bench but powerful enough to drill through metal, wood, plastics, and more. Drill up to a 1/2-inch hole in heavy-duty cast iron. Its powerful induction motor features ball bearing construction for an extended life, providing smooth and balanced performance even at high speeds. The 1/2-inch JT33 chuck gives you versatility with a variety of bits while the worktable bevels up to 45° left and right. Constructed with a rigid frame and a cast iron head, table, and base, ensure accurate holes and convenient drilling operations every time. Remember when you could drill holes in any material with ease? Remember WEN.

Locking Depth Adjustment

Set the depth adjustment knobs to limit your spindle travel for accurate and repeatable drilling operations.

Beveling Worktable

Bevel the worktable 45° left and right for precisely angled holes.

Onboard Key Storage

Place your chuck key on the attached key storage to make sure it is alway there when you need it.

1/2-inch Keyed Chuck

The JT33 chuck accepts drill bits up to a 1/2-inch in size to meet the needs of a variety of projects.

Product description

The MICRO Mill FF 230 is a small, accurate milling system used to mill, drill and countersink steel, cast iron, aluminum, brass and plastic. The headstock swivels through 360°, indicated on a scale. Height is adjustable. One revolution equals 1/32" (1mm) travel, 1 division equals .002" (0,05mm). The quill and headstock may be locked in position, which is essential when milling. The powerful permanent magnet motor drives via a poly-v-belt, yielding high torques, especially at lower speeds. The machine comes with three collets of 15/64", 5/16" and 25/64" (6, 8 and 10mm). The solid table has a size of 10 5/8" x 3 5/32" (270 x 80mm) and is T-slotted to 15/32" x 15/64" x 13/64" (the MICROMOT norm of 12 x 6 x 5mm). Technical data: Speeds 280 - 550 - 870 - 1,200 - 1,500 - 2,200rpm; Table Size 10 5/8" x 3 5/32" (270 x 80mm), Column Size Ø 1 3/8" x 15 3/4" long (35 x 400mm); X-Y Travel 6 11/16" x 2 9/16" (170mm x 65mm); Overall Height 20" (500mm); Volts 110 - 120V AC, 60Hz; Weight 41 lb. (17kg) Important: For best results when milling, it is recommended to lock the headstock. This is easily done via the FF 230's lock levers.

From the Manufacturer

Proxxon micro mill FF230 is a small, accurate milling system used to mill, drill, and countersink steel, cast iron, aluminum, brass, and plastic. The headstock swivels through 360-Degree indicated on a scale. Height is adjusted via a zero adjustable hand wheel, also used as a fine feed when milling. One revolution equals 1/32-Inch (1mm) travel, 1 division equals .002-Inch (0.05mm). The quill and headstock may be locked in position, which is essential when milling. The powerful permanent magnet motor drives via a poly-v-belt, yielding high torques, especially at lower speeds. The machine comes with three collets of 15/64-Inch, 5/16-Inch and 25/64-Inch (6, 8, and 10mm). The solid table has a size of 10-5/8-Inch by 3-5/32-Inch (270 by 80mm) and is T-slotted to 15/32-Inch by 15/64-Inch by 13/64-Inch.

• Quiet, precise and vibration-free for fatigue free use
• Low weight and slim design, without ever compromising performance
• High quality precision tools
• Model Number: 34108

User questions & answers

Question:	Are there any cnc conversion kits for this? i'm looking to make a circular hole on an aluminum phone case. suggestions
Answer:	No, they are not the same. Galaxy S6 Lite released in 2020 ONLY. If you have purchased the tablet in 2019, then this case will NOT FIT your tablet correctly.
Question:	Con que voltaje trabaja
Answer:	No.
Question:	How does this compare to the micro mill mf 70 from proxxon
Answer:	Please identify the exact model of your tablet first. If it shows SM-P610/P615, then this case will fit your tablet. Otherwise no. You can use the settings menu to locate it. Here's how: Browse to SETTINGS > GENERAL > ABOUT DEVICE Your model number will be listed
Question:	Is the ff 230 suitable for tapping light metals and plastics? it would need a reverse switch, and depth control. what tips do you have for tapping
Answer:	Yes, it works with iPhone 7. It is not suggested to put on any protective phone case. Please find the item size here: https://images-na.ssl-images-amazon.com/images/I/61myErXQ7CL._SL1500_.jpg

Product description

Baileigh mill drill lathe have a small shop and always looking for more room. How about combining three larger machines into one. Baileigh Industrials unique mill drill lathe is the answer for anyone looking to get maximum versatility from the tools. Combines 3 machines into one small package, giving the operator the choice for milling, drilling, or performing lathe operations and opening up floor space for more tools. Although the MLD is small in stature, it has all the features that an operator would want in a 3 in 1 combination machine. Precision ground and hardened ways ensure long life and years of machining on the MLD-1030. Adjustable RPM from 50-2000 and includes a digital read out for accurate cutting speed. Being that the leath features two powerful 110V 1HP motor that allows you to operate anywhere there is a standard outlet. There is one motor for the lathe and mill independently. This gives for longer life and less wear and tear on the motors. Steady rest, follow rest, three jaw chuck, and four jaw chuck are just a few of the options that come standard on this mill drill lathe. The milling and drilling head of the mill drill lathe is as sturdy as any on the market. It head itself feature a column style base with adjustable depth. A digital readout will help to keep the depth of cut a precise as possible. A robust MT-2 taper is also standard of the MLD-1030. Specifications - Range of longitudinal feed per revolution: 0.003-0.008-inches; Range of metric threads: 0.4-3.5 millimeters; 50-2000 rpm variable speed; 1.1-inches spindle bore; 8-56 TPI range of inch threads; 2-inches top slide travel; 5-19/64-inches width of bed; 2-inches spindle stroke. 2-inches tailstock quill travel; MT 2 taper of spindle bore; MT 4 taper of tailstock quill; swing over bed 9-3/4-inches; swing over cross slide 5.7-inches; maximum distance spindle to column 6.5-inches; maximum distance spindle to table 11-inches; cross slide travel 4.5-inches; distance between centers 29-1/2-inches.

• 120 Volts power
• Mill, drill and lathe all in one
• lathe features adjustable rpm from 50-2000 and includes a digital read out for accurate cutting speed
• 2-inches spindle stroke
• 29-1/2-inches distance between centers

User questions & answers

Question:	It says 7 in spindle to table? Would it spin 13 inch
Answer:	No
Question:	does it come with the stand
Answer:	It has several nuts on the back of the chuck you can remove.

Product features

Sheet Metal Stand

Includes a sheet metal stand, but you can also use this mill drill lathe on your bench top.

Lathe Digital Read Out

Adjustable lathe speed from 50 to 2,500 rpm with a digital read out for precise cutting.

Traditional Drill Press

Yoke on stationary mill allows you to drill as on a traditional drill press.

Product description

The table is suitable for Mini Drill and drill bracket series.

It can also apply to other suitable machine.

The work table is composed of several adjustable dovetail slotaluminum alloy composition,

can guarantee the minimum space and ensure the accuracy.

The working table comes with 3 # Hexagonal wrench * 1,

exquisite equipment * 1, M8 * 30

Zero adjustment handwheel rotates a circle of 1.50 mm. A lattice is equal to 0.05mm.

Adjustable for X direction:190mm,

Adjustment for Y direction:67mm



Package includes:

1 Pc of Milling Table of Medium Version.

• The table is suitable for Mini Drill and drill bracket series. It can also apply to other suitable machine.
• The work table is composed of several adjustable dovetail slotaluminum alloy composition, can guarantee the minimum space and ensure the accuracy.
• The working table comes with 3 # Hexagonal wrench * 1, exquisite equipment * 1, M8 * 30
• Zero adjustment handwheel rotates a circle of 1.50 mm. A lattice is equal to 0.05mm.
• Adjustable for X direction:190mm, Adjustment for Y direction:67mm

User questions & answers

Question:	What are the dimensions of the slots
Answer:	The heart is about an inch. I used them to cut cheese for a charcuterie board.
Question:	Will this be ok to hold something about 6kg
Answer:	Yes but they are small. They are about the diameter of a cucumber.