14 best craftsman stud finder

Product description

CRAFTSMAN Stud sensor works on surfaces covered in wallpaper and fabric. Edge detection to help locate stud edges of both wood and metal stud.

• Depth range of 3/4 inch through drywall, works on surfaces covered in wallpaper and fabric
• Edge detection to locate stud edges of both wood and metal stud
• Shock resistant and water resistant body for durability and long life
• Takes 9 volt battery
• Full Lifetime Warranty, refer to "Warranty and Support" section below for full details
• Battery not included

User questions & answers

Question:	What kind of batteries does this need
Answer:	This unit takes a 9 volt battery
Question:	is it a good stud finder for mounting a TV
Answer:	No, it isn’t a good stud finder at all. Spend $10 more at Lowes for one that actually works.

Product description

This CRAFTSMAN Stud sensor detects center of stud for accruate results, detects wood and metal up to 1-1/2 inches and up to 2 inches in metal. This stud sensor also has auto calibration for consistent readings, detects presence of live AC, and the center marking pin provides a visual reminder of stud location.

• Detects center of stud for accurate results
• Detects wood and metal studs up to 1-1/2inches Deep
• Auto calibration for consistent readings
• Detects presence of live AC
• Center marking pin provides a visual reminder of stud location
• Thin Profile for Ergonomics and Storage
• LED Arrows and Audible Notifications of Stud Location
• Full Lifetime Warranty, refer to "Warranty & Support" section below for full details

User questions & answers

Question:	Can this device locate a wood stud up to 3 inches
Answer:	Had to look long and hard to find the weight of this chair...Wish manufacture had mentioned it...i feel this is an important point
Question:	Where was this made
Answer:	When the tape is in the unlocked position, it will retract back into its case.
Question:	Does the 3-inch depth version have rubber feeling grips or is it hard black plastic
Answer:	I think it's about an inch. Only lasted me a couple weeks at work. Blade snapped at the 7' mark.

• Depth range of 3/4 inch through drywall, works on surfaces covered in wallpaper and fabric
• Edge detection to locate stud edges of both wood and metal stud
• Shock resistant and water resistant body for durability and long life
• 1) magnified center block vial for durability and accuracy
• 2) extruded aluminum body for strength and lightweight
• 3) over-molded rubber end caps for non-marring leveling and shock resistance

Product description

This CRAFTSMAN metal and wood stud Finder detects center of stud for accurate results up to 3/4-in depth and has auto calibration for consistent readings. In addition, detects the presence of live AC.

• Detects center of stud for accurate results
• Detects wood and metal studs up to 3/4inches Deep
• Auto calibration for consistent readings
• Detects presence of live AC
• Thin profile for ergonomics and storage
• LED Arrows and Audible Notifications of Stud Location
• Full Lifetime Warranty, refer to "Warranty & Support" section below for full details

User questions & answers

Question:	Can it detect properly through plywood walls
Answer:	Has a company name on it from Huntersville NC in USA but honestly I do not know if it was manufactured there nor can I guarantee where it originally came from. We order it from Irwin Tools is all I can say for sure.

Product description

We're on the level with our laser levels for construction. CRAFTSMAN leveling, measuring, and stud finding tools are accurate, compact, and easy to use. Laser levels are available in red or highly visible green laser beam options. Cross lines are perfect for installation of partitions, shelves, cabinets, tile, and flooring. Our laser level with integrated stud sensor combines two tools in one, its detects both wood & metal studs as well as Live AC. In addition, it also projects a horizontal laser line. Other models can accurately identify stud edges or center points as well as energized wires. This laser distance measurer works off AA batteries and provides accuracy measurements at the click of a button. Two out of the three will also allow for easy area and volume calculation capabilities.

• VERSATILITY: 2-in-1 laser level tool & stud sensor
• SELF-LEVELING LASER LEVEL: Laser levels automatically
• ACCURACY: 1/8-inch accurate construction laser
• CONVENIENCE: Automatic reference for angled lines
• VISIBILITY: 20 ft. Visible Range
• STUD LOCATION FINDER: Center marking channel for marking stud location
• Laser Class II @ ≤1mW @630~680 nm
• Limited Lifetime Warranty, refer to "Warranty & Support" section below for full details

User questions & answers

Question:	Is this item manufactured in usa or is it chinese
Answer:	We attached ours to folding beach chairs. We placed them where they wouldn't impede unfolding. Just play around with it. It isn't hard to figure out.

Product description

The item is Black & Decker BDL190S BullsEye Auto-Leveling Interior Line Laser with Stud Sensor . Used for Test & Measurement, Levels. The product is manufactured in China. Amazon.com The Black & Decker BDL190S BullsEye Auto-leveling Interior Line Laser and Stud Sensor Combination Tool is an ideal tool for hanging pictures, detecting wood and metal studs, locating live A/C wires, and installing decorative items. With patented auto-leveling technology, this leveler is actually two tools in one--an auto-leveling laser level and a stud sensor. Its auto-leveling laser levels automatically without adjustments and projects horizontal laser lines. Other features include a stud sensor to detect wood, metal, studs, and live A/C wires and an easy to read LCD display. Categorized as a class II laser, this laser level comes backed by a 2-year limited warranty.

The Black & Decker BDL190S BullsEye Auto-leveling Interior Line Laser and Stud Sensor Combination Tool is an ideal tool for hanging pictures, detecting wood and metal studs, locating live A/C wires, and installing decorative items. With patented auto-leveling technology, this leveler is actually two tools in one--an auto-leveling laser level and a stud sensor. Its auto-leveling laser levels automatically without adjustments and projects horizontal laser lines. Other features include a stud sensor to detect wood, metal, studs, and live A/C wires and an easy to read LCD display. Categorized as a class IIIR laser, this laser level comes backed by a 2-year limited warranty.

• Two tools in one--an auto-leveling laser level and a stud sensor
• Detects wood, metal, studs and live A/C wires
• Patented auto-leveling technology
• Easy to read LCD display
• 2-year limited warranty
• This is a Class 3R laser product, Power output ≤ 5mW
• Laser Class IIIa, <5mW @ 633nm-670nm

User questions & answers

Question:	Does it really come with a case? Some say it does, some say it does not. Which is it
Answer:	The clear display package it comes in is considered to be the “case”. The display package opens up like a book once you cut the black band keeping the two sides together. If you’re expecting a traditional nylon case, then you will be disappointed. I was disappointed when I found out there was no nylon case, but the provided packaging works just fine for me now. Thank you.
Question:	Can the device put out correct vertical lines if turned 90 degrees
Answer:	No, only horizontally. When you go vertical the laser isn't a sharp line
Question:	Does this come with a case
Answer:	yeah, the plastic case it comes in is the case. Not a fan
Question:	How does the unit afix to the wall
Answer:	A hanger is included to attach to the wall

Product features

BullsEye Auto Leveling Laser

- BullsEye auto-leveling technology

- Two tools in one to simplify hanging and mounting projects

- Levels automatically for precise BullsEye results

- Projects horizontal level line

- Stud sensor detects wood and metal studs plus live A/C wires

- LCD Display Easy To Read

• The Most Accurate Wall Scanner- Tavool specializes in stud finder for years and adopts the most Advance Sensors Technology for accurately & quickly locating studs wood metal AC wires! In all modes, this wall scanner always detect and indicate the Live AC Wire. Whether you are a professional, homeowner or a DIY enthusiast, you can find great use in this electronic stud scanner
• 4 IN 1 Multiplication Plus Deep Detection - This digital wall scanner includes four different scanning modes for woods, beam, joist, metals, AC wires and deeply embedded objects behind floor, ceiling, wall. Stud mode detects wooden beams and joists in drywall up to 1.2 inches. Metal mode detects pipe , rebar, aluminum and copper up to 1.57 inches.Deep mode detects wood and metal parts located up to 1.77 inches while 85~240 volt AC current for voltage and live electrical lines up to 2.36 inches
• Upgrade Design of LCD Screen - Displaying the Desired Stud Material As Well As the Precise Position of the Stud - The Tavool digital stud scanner features large LCD display together with the big sound to detect the accurate location of stud metal Ac wires. When find the material, the LCD display will indicate the direction and the intensity of sound tells whether you are more close to the target. The fast detection saves users time and efforts, making the task completion EASIER
• Automatic Calibration and Ergonomic Grip for Comfortable Use - Turning on the stud finder and Completing Calibration. The automatic calibration before using provides users with maximum reliability and accuracy. Then put it on the wall. The wood beam finder will flash once it has picked up the edge of a stud.The ergonomic design of this wall stud finder makes it comfortable to hold from any angle
• Professional Design with Top Quality - Tavool has been dedicated to Research and develop stud finders for many years, and we have a professional team and mature productions process. This stud joist finder wall detector can quickly locate the metal wood AC wire that are hidden in the walls, floors and ceilings of your house, help you find the exact stud while installing TVs, cabinets, garage shelves etc.

User questions & answers

Question:	Is there an instruction manual online? I misplaced the manual that came in the box
Answer:	Si puede solicitar un manual de instrucciones en [email protected]
Question:	Will this locate studs behind bathroom tiles
Answer:	If your tile wall has cement backer board, then this device will not work. If your tile is backed by sheetrock, then it will probably work unless your tile is took thick. I wouldn't trust it to locate pipes behind tile, so take care if you're working in a bathroom.
Question:	Is the battery included
Answer:	No the 9volt battery is not included.
Question:	Can this detect a stud behind plaster walls
Answer:	This tud finder can quickly locate metal, studs, joists, pipes, live AC wire behind all kinds of walls floors and ceilings but except the cement board wall, you can use it on popcorn ceilings, plaster walls, textured surfaces,etc

Product features

Stud Scan Detection

Deep Scan Mode scans through 2 layers of drywall up to 1.5 in. (38 mm) deep. DeepScan Mode is a higher sensitivity scanning mode that should be used when there are extra layers of wallboard or paneling. To minimize false positives and/or finding other objects further behind the wall that may not be a stud, always start your scan in StudScan Mode first.

Metal Scan Detection

Tavool wall canner will locate metal studs in StudScan, DeepScan, and Metal Scan Modes. Since Tavool stud finders are looking for a change in density behind drywall, not a particular material, in StudScan and DeepScan Modes the detector will react to metal studs the same as it would for wooden studs.

After you detect the center of a object, Please Use Metal Scan to determine if the previous reading in Stud scan was a wood stud, metal stud, or pipe.

Live AC Wire Detection

AC Wire detection indicates the presence of live, unshielded electrical wiring up to 2 inches (51 mm) deep. In all modes, this wall scanner always detect and indicate the Live AC Wire.

Note: AC Wire Detection works in both StudScan / DeepScan / MetalScan Modes. The AC Wire Detection Icon will flash when live, unshielded wires are detected.

Step 1:Calibrate the tool before every scan

After choose the mode, press and hold the scan button( on the side of the tool) to calibrate this tool. Wait for the reducing bars disappeared and beep to confirm calibration has completed.

In stud/deep mode, put it on the wall where you want to detect to calibrate it ;In AC/Metal mode, put it in the air to calibrate it.

Step 2: Scan the wall

Hold down the button, then move the stud finder along the wall slowly, if shake or lift the scanner accidently, the device needs to be re-calibrate.

The narrow on the screen togather with the beep signal alter, guides you to find the location of the stud.

Step 3: Find the location of the stud

When the signal bar is full and the beep alarm is loudest, it means you have found the center of an object.Mark it with your pencil.

Then choose the Metal Scan mode to test whether it is a metal. After you confirm that it is not a metal, it means that you found the center of a stud. (More details refer to the above description of "Metal Scan Detection")Then you can drill it to hang thing

Product description

There are two tips to ensure the wall scanner never trick you again

1. Go slowly: To be effective, stud finders need to be properly calibrated. First, place yours on the wall and turn it on — you can usually do this by holding in a button. Let the stud finder read the density of the material (this will only take a second or two and you will hear the sound of " beep"), then slowly move it from side to side. Go back and forth over the wall a few times, starting from a different spot with each pass. Mark each stud you discover with a pencil. We recommend finding three and using a tape measure to make sure they are the same distance apart. This will help you avoid false positives.

2. Always double-check: After you have marked your studs and where you want to drill your holes, you should use something to poke into the wall to ensure you actually marked a stud. We would recommend doing this by hand, rather than using a power tool, as you will have a better feel for what’s inside the wall. You can also tap a small nail into the wall; get past the drywall without the nail “falling in” and you’ve found a stud. The last thing you should do before drilling is poke a little hole to the left and right of where you want to drill and make sure you are still on the stud. This will ensure you are centered on a stud, and not just clipping its side (and possibly hitting electrical wiring).

• 🔨 7 in 1 Multi Detection Function: Upgraded wall scanner features detection for wood stud mode, deep stud scan, metal objects mode (iron and non-ferrous metals), copper conductors mode (live), and with the added benefit of detecting moisture in wood and building materials helping you quickly & easily locate wood metal studs joists beams metal pipes rebar & live AC wire behind walls floors ceilings
• 🔨 Accurate Center Finding : Features large LCD display together with the big sound warning to detect the accurate location of the objects. Stud finder will beep once it has run to the center of a stud. Automatic calibration before using provides users with maximum reliability & accuracy and easy to finder the center of the stud
• 🔨 Upgraded Measurement Modes: The ability to measure the moisture content of wood and building materials can be of great help in wood processing, water damage repair, and home renovation. Also, air temperature can be sensed and displayed in 2 modes, including ℉ and ℃
• 🔨 Make DIY Home Project Easier: our wall detector sensor is lightweight, long-lasting and convenient to use in your home, office, workshop. Makes all of your DIY home projects easier such as mounting your TV, bathroom cabinet, photo frame, garage racks etc.
• 🔨 US-based Customer Service: We are ready to provide the accurate stud finder at a great value and glad to answer your pre-purchase and use questions. If you run into questions, our US-based customer care team 7 days a week to help you out

User questions & answers

Question:	Will this stud finder detect studs behind lath and plaster walls
Answer:	Due to the irregularities thickness of plaster, maybe it is difficult to locate studs by using Stud scan modes, change it to Metal Scan mode to locate the metal nail on the stud to estimate the stud position. If you have further questions, feel free contact us via email
Question:	What is the moisture detection function
Answer:	It can detect moisture in wood and building materials and provide better service to more DIY workers.
Question:	Can it detect ac wire behind the bricks wall
Answer:	Thanks for your question. Yes, it can detect AC wire behind the bricks wall. If you have any other questions, please feel free to contact us: [email protected]
Question:	What is the moisture detection function
Answer:	Moisture detection function means the wall scanner can detect moisture in wood and building materials and provide better service to more DIY workers. If you have any questions in the using, feel free contact us via email on the manual

Product features

PERLESMITH STUD FINDER - Make Your DIY Home Project Easier

Stud Scan

Stud scan mode: Locates the center and edges of wood and metal studs up to 3/4 in. (19mm) deep.

Deep Stud scan mode: Locates the center and edges of wood and metal studs up to 1 ½ in. (38mm) deep.

Metal Scan

Metal Scan mode: Detects metal up to 2 2/5 inches (60mm) deep.

Use this Metal Scan Mode to locate and avoid hazards, such as pipes, behind walls and determine if a stud is wood or metal.

AC Wire Scan

AC wire Scan mode: Detects live unshielded AC wires up to 2 inches (51mm) deep.

For Safety, in all modes, this wall scanner always detect and indicate the Live AC Wire.

Tip: WireWarning Detection works in both StudScan / DeepScan / MetalScan Modes. The WireWarning Detection icon will show when live, unshielded wires are detected.

Step 1: Calibrate

After selecting the desired mode, place this tool flat against the wall, then press SCAN BUTTON to start calibration.

Tip: It is important to wait for the calibration to complete (2-3 seconds) every time before moving the scanner.

Step 2: Moving

The decreasing bars will disappear and buzzer will beep, indicates the calibration is completed. Continue to keep the tool flat against the wall and begin scanning according to the arrow.

Step 3: Center Finding

Continue sliding, a full bars arrow with CENTER words will display, and beep sounds after locating the center of the stud.

If the thickness of the surface is unknown, you can start with Deep Stud scan mode first, and then choose a more suitable Scan Mode to improve the accuracy.

Product description

From BLACK & DECKER, detects wood studs up to 3/4" thick. For ease of use, sensor lights and beeps when stud is detected. Requires two AA batteries (included). use for detecting wood studs. Orange with BLACK.

Black & Decker's Stud Finder is a simple, yet indispensable tool that detects the location of studs up to 3/4-inch thick. This compact, easy-to-use stud finder operates by moving over the surface of the wall. LED lights on the stud finder light-up to accurately indicate the location of studs.

From the Manufacturer

Black & Decker Stud Sensor takes the guesswork out of locating wood studs to hang pictures, install closet shelving, run chair railing and more. Whether you are a pro, do-it-yourselfer or decorator, this Stud Sensor will help you get the job done faster and easier. Stud Sensors detect studs through walls by sensing the differences in wall density between studs and the hollow spaces in your walls. This Stud Sensor has both audible and visual indicators that show when the edge of a stud is located. It is always best to hang shelves, photographs, artwork and other items securely into the studs in your walls. If these items are secured only in the drywall, nails and anchors can come loose under their own weight over time. With the diameter of a stud being less than 1-inch thick and studs being placed either every 16 inches or 24 inches, depending on the construction of your home, it isn't always easy to guesstimate a stud's location. Without a stud sensor you can only guess where studs may be hidden under your walls. This usually results in driving a nail or anchor between the studs in the empty spaces in your walls, leaving holes.

• Plastic
• Made in the USA or Imported
• Detects studs edge-to-edge up to 3/4" thick
• Leds Flash and the device beeps when studs are located
• Ergonomic design
• Included Components: AA Batteries
• Stud sensor with LED indicators for accurate stud locating

User questions & answers

Question:	I hae this model stud sensor and just put new batteries in it (twice) and it still will not light up. What can I do to make it work?????Tony
Answer:	Did you leave batteries in it while stored? If so, battery acid may have corroded contacts. You may have to replace it. Always store without batteries. I haven't had this issue yet. Just my experience with other electronics.
Question:	this black & decker™ sf100 wood stud finder works exclusively with wood studs
Answer:	Yes, SF100 detects wood studs in walls up to 3/4-inch thick.
Question:	Is this dishwasher safe
Answer:	No, it is not dishwasher safe.
Question:	Will this work on metal studs
Answer:	No, SF100 detects Wood Studs up to 3/4" thick.

Product description

There are two tips to ensure the wall scanner never trick you again

1. Go slowly: To be effective, stud finders need to be properly calibrated. First, place yours on the wall and turn it on — you can usually do this by holding in a button. Let the stud finder read the density of the material (this will only take a second or two and you will hear the sound of " beep"), then slowly move it from side to side. Go back and forth over the wall a few times, starting from a different spot with each pass. Mark each stud you discover with a pencil. We recommend finding three and using a tape measure to make sure they are the same distance apart. This will help you avoid false positives.

2. Always double-check: After you have marked your studs and where you want to drill your holes, you should use something to poke into the wall to ensure you actually marked a stud. We would recommend doing this by hand, rather than using a power tool, as you will have a better feel for what’s inside the wall. You can also tap a small nail into the wall; get past the drywall without the nail “falling in” and you’ve found a stud. The last thing you should do before drilling is poke a little hole to the left and right of where you want to drill and make sure you are still on the stud. This will ensure you are centered on a stud, and not just clipping its side (and possibly hitting electrical wiring).

• 🔨 5 in 1 DEEP DETECTION FUNCTION: our wall scanner wood stud finder features 5 scanning modes respectively. Includes 1/2” stud scan, 1” stud scan, 1.5” stud scan, metal scan & AC scan. Helps you quickly & easily locate wood, metal studs, joists, beams, metal pipes, rebar & live AC wire behind walls, floors, ceilings
• 🔨 HELPFUL LCD DISPLAY & SOUND WARNING: this wall detector features a large LCD display & sound warning to help detect the accurate location of the objects. Saves you lots of time by displaying the desired stud center & the precise position of the stud
• 🔨 HIGHLY COMPATIBLE: our wall stud finder sensor is lightweight, long-lasting and convenient to use in your home, office, workshop. Makes all of your DIY home projects easier such as mounting your TV, bathroom cabinet, photo frame, garage racks etc.
• 🔨 AUTOMATIC CALIBRATION AND SIMPLE USE: turn on the stud finder and complete calibration by placing it on the wall. The finder will flash and beep once it has picked up the edge of a stud. Automatic calibration before using provides users with maximum reliability & accuracy
• 🔨 COMFORTABLE ERGONOMIC DESIGN: the ergonomic design means you can hold the wall scanner in your hand comfortably. Strong grip let’s you hold the electric stud finder tightly & keep it moving correctly to get more accurate results. Suitable for all types of people

User questions & answers

Question:	Can I use this wall detector to check the metal studs
Answer:	Thanks for your question. Yes, this stud finder wall scanner can easy locate metal studs on your wall. If you have any other questions, please feel free to contact us: [email protected]
Question:	I want to find stud behind the wall, is it hard to use
Answer:	Thanks for your question. Our wall scanner wood stud finder has 5 scanning modes . Includes 1/2” stud scan, 1” stud scan, 1.5” stud scan, metal scan & AC scan. It can helps you quickly and easily locate wood, metal studs, joists, beams, metal pipes, rebar & live AC wire behind your walls. If you have any other questions, please feel free to contact us: [email protected]
Question:	Will this stud finder locate metal studs
Answer:	Thanks for your question. Yes, our wall scanner stud finder can help you easily locate metal studs behind your walls. If you have any other questions, please feel free to contact us: [email protected]
Question:	I want to install the TV wall mount, can I use this stud finder to locate wooden stud
Answer:	Thanks for your question. Yes, you can use this stud finder wall detector to locate wood studs in your wall. If you have any other questions, please feel free to contact us: [email protected]

Product features

5 IN 1 STUD FINDER WALL SCANNER - MAKE YOUR DIY HOME PROJECTS EASIER

Step 1: Calibrate the device before every scan

After choose the mode, press and hold the scan button( on the side of the device) to calibrate this device. Wait for the reducing bars disappeared and beep to confirm calibration has completed.

In stud/deep mode, put it on the wall where you want to detect to calibrate it ;In AC/Metal mode, put it in the air to calibrate it.

Step 2: Move along the wall

Hold down the button, then move the stud finder along the wall slowly, if shake or lift the scanner accidently, the device needs to be re-calibrate.

The arrow on the screen will guide you to find the direction of the stud.

Step 3: Find the center of the stud

When the signal bar is full and the beep alarm is loudest, it means you have found the center of an object. Mark it with your pencil.

Then choose the Metal Scan mode to test whether it is a metal. After you confirm that it is not a metal, it means that you found the center of a stud. Then you can drill it to hang things.

STUD SCAN AND DEEP SCAN

Use Stud Scan Mode to find the center or metal studs up to 1.5 in. (38 mm) deep.

DeepScan Mode is a higher sensitivity scanning mode that should be used when there are extra layers of wallboard or paneling. To minimize false positives and/or finding other objects further behind the wall that may not be a stud.

In order to get the accurate results, please always start in Stud Scan Mode when looking for studs.

METAL SCAN

Wall scanner will detect metal up to 2.36 in. (60 mm) deep.

Use this Metal Scan Mode to locate and avoid hazards, such as pipes, behind walls and determine if a stud is wood or metal.

For maximum accuracy, press and hold the Power Button while holding the scanner away from the surface. Once a short beep sounds confirming calibration complete, place against the surface to be scanned. Make sure to continue to hold the Power Button.

AC WIRE SCAN

Wire Warning detection indicates the presence of live, unshielded electrical wiring up to 2 inches (51 mm) deep.

For Safety, in all modes, this wall scanner always detect and indicate the Live AC Wire.

Note: WireWarning Detection works in both StudScan / DeepScan / MetalScan Modes. The WireWarning Detection Icon will show when live, unshielded wires are detected.

• ★【5 in 1 Multi-Function Mode】Compared with other stud sensors, Meterk stud finder not only featuring detection for wood stud exact mode, wood stud deep mode, metal objects mode (iron and non-ferrous metals), copper conductors mode (live), but also detection for moisture in the wood and building materials, offering a wider range of detection performance
• ★【Locate the Center of Stud !】Meterk stud finder can be used to find the center of the stud in just once the operation. When the stud sensor is approaching the center of the stud, the signal strength will increase and accompany the sound. At the center, the center icon "+" will appears and the signal strength shows 100% full on the screen. However, other products need to be operated twice in the left and right direction to find the center by looking for the edge of the stud
• ★【Wood Exact/Deep Mode】Stud sensor can detect metal, wood and live cables in walls, ceilings, and floors. Wood exact mode scans through one layer of drywall up to 0.79 inches (20mm) thick. Deep mode scans through 2 layers of drywall up to 1.50 inch (38 mm) deep. Deep stud scan mode is a higher sensitivity scanning mode that should be used when there are extra layers of wallboard
• ★【Convenient Design】Meterk sensor detector has a mute setting, which is very convenient for those who think that the alarm sound is annoying or use it somewhere in the library. This sensor detector has a large LCD display, the backlight function supports to detect studs even in dark environments. Whether you are a professional, a homeowner or a DIY enthusiast, you can find good uses in it
• ★【Make Your DIY Homework Easier !】 This wall detector quickly locates the center of the material, helping you avoid danger when installing TV, cabinets, garage racks, and more. The ability to measure the moisture content of wood and building materials can be of great help in wood processing, water damage repair, and home renovation. 1 x Meterk stud finder, 2 AAA battery, 1 x portable bag, 1 x user manual, 1 x warranty card( 24 month ).

User questions & answers

Question:	Can this detect roof rafters through roof shingles
Answer:	No dosent work
Question:	What is the moisture detection function
Answer:	It can detect moisture in wood and building materials and provide better service to more DIY workers.
Question:	How about the product warranty
Answer:	24-month warranty and you can contact them if stud detectors have quality problems occur during the warranty period.
Question:	What are the maximum depth of the metal tube and copper conductor
Answer:	copper conductors(live): 50mm /1.97 inch, ferrous metals: 60mm /2.36 inch, non-ferrous metals(copper): 50mm / 1.97 inch

Product features

Step 1

* Short press the power button on the Meterk stud sensor.

* Short press the wood detection mode button to enter the wood stud detection mode, the wood detection mode is the exact model.

* Long press this button to switch to the wood deep detection mode.

(The maximum detection depth of the "exact" mode is a 20mm/0.79 inch, and the maximum detection depth of the "deep" mode is 38mm/1.50 inch).

Step 2

* When the stud sensor starts to approach the stud, it will always be accompanied by a sound, the signal percentage scale on the right side of the screen will gradually increase, and the distance will be displayed on the screen will gradually shorten.

* When the positioning symbol "+" appears on the screen, indicating that the center of the stud has been found, mark it with the pen at the groove.

* Note! At this time, you cannot directly drill in the second step!

Step 3

* Since Meterk stud sensor is looking for a change in density behind drywall, not a particular material. In stud scan and deep scan modes the detector will react to metal studs the same as it would for wooden studs.

* To ensure that the object detected in the second step is a wood stud, switch to the metal mode for testing again. In the metal mode, if nothing happens on the screen, it means that the object found by the second step stud sensor is wood.

* At this time, you can rest assured and start your DIY and drilling work !

Metal / AC Wire Scan Detection - Avoid the Metal / Wire Behind the Wall for Punching

Step 1: When the Meterk stud sensor is close to the metal/wire, the display scale bar on the screen will gradually rise and make a sound, when the distance displayed on the screen becomes at 6cm, it means that the product has started to detect metal. At this time, it should be marked with a pen at this position, and the mark point is "1" (as shown).

Step 2: The stud sensor will continue to move from the marker point "1" position for a distance, and the distance displayed on the screen will be shortened. When the center icon "+" appears on the screen, it represents metal/ The wire is positioned just below the center of the stud sensor.

Step 3: When the instrument is slowly moving away from the object, the display scale will slowly drop and the distance displayed on the screen will become 6cm again. At this position, mark it again with the pen and mark it as “2” (as shown). .

Step 4: There is a metal/wire in the area formed between the marked points "1" and "2".

Note: Before starting the drilling work, you should avoid this area!

Moisture Measurement

• Meterk stud sensors measure the moisture of wood and building materials. If you need to freeze this value, just press the "HOLD" button.
• Wood moisture measurement range: 5%-50%/±2%, building materials: 1.5%-33%/±2%. (There are two test pins at the bottom of the instrument)

Mute Setting

• Press the 1 and 2 buttons at the same time tset the sound to mute. There for people who think the alarm sound is annoying or to use it in someplace like a library.

Make Your DIY Homework Easier!

• This wall detector quickly locates the center of the material, helping you avoid danger when installing TV, cabinets, garage racks, and more. The ability to measure the moisture content of wood and building materials can be of great help in wood processing, water damage repair, and home renovation.

Product description

PrvnPro Stud finder sensor tool has a 2 inch backlit display and a sound indication for detecting wood, metal, and alternating currents. PrvnPro stud finder tool has a rubberized and ergonomic grip and easily glides along walls. PrvnPro stud finder is the ideal tool for any professional contractor or any at home DIY project.

• Yellow and Black Finish
• Wall scanning stud finder tool with sound indicator has three modes that detects wood, metal, and alternating currents.
• 2 inch LED backlit display
• Rubberized ergonomic grip
• Dimensions: 6-Inch L x 2. 74-Inch W x 1. 25-Inch D

Product features

Woos Stud Scan

Wood mode can scan wood studs up to 1.5-inches wide.

Metal Scan

Metal mode can detect pipes or metal studs avoiding hazards before drilling into walls.

AC Wire Scan

Alternating Currents mode can detect electrical wiring inside of walls.

Product description

Whether you’re hanging a picture, mounting a TV, renovating part of your home, or working as a professional contractor, you need to know what is on the other side. Our stud finder is one of those tools that you will eventually need. PERLESMITH stud finder can help you finish your DIY home project well. The wall detector features large LCD display, ergonomic design and multi-sense technology for accurate detection of both metal and wooden studs. It will also detect live wiring up to two inches into walls and metal up to 2.36 inches deep. The five scanning modes (1/2” stud scan, 1” stud scan, 1.5” stud scan, metal scan & AC scan) make it ideal for both tradesmen and home carpenters. With this device, you can immediately find a suitable place on the wall without making any extra holes

There are two tips to ensure the wall scanner never trick you again

1. Go slowly: To be effective, stud finders need to be properly calibrated. First, place yours on the wall and turn it on — you can usually do this by holding in a button. Let the stud finder read the density of the material (this will only take a second or two and you will hear the sound of " beep"), then slowly move it from side to side. Go back and forth over the wall a few times, starting from a different spot with each pass. Mark each stud you discover with a pencil. We recommend finding three and using a tape measure to make sure they are the same distance apart. This will help you avoid false positives.

2. Always double-check: After you have marked your studs and where you want to drill your holes, you should use something to poke into the wall to ensure you actually marked a stud. We would recommend doing this by hand, rather than using a power tool, as you will have a better feel for what’s inside the wall. You can also tap a small nail into the wall; get past the drywall without the nail “falling in” and you’ve found a stud.

• 🔨 Upgraded 5 in 1 Stud Finder Wall Detector: wall scanner wood stud finder features 5 scanning modes respectively. Includes 1/2” stud scan, 1” stud scan, 1.5” stud scan, metal scan & AC scan. Helps you quickly & easily locate wood, metal studs, joists, beams, metal pipes, rebar & live AC wire behind walls, floors, ceilings
• 🔨 Clear LCD Display & Sound Warning: stud detector features a large LCD display & the beeping sound to help you get a more accurate result in both visible and audible way. Saves you lots of time by displaying the desired stud center & the precise position of the stud
• 🔨 To Be DIYer: our wall stud finder sensor is lightweight, long-lasting and convenient can be applied to various wall surfaces, from lath, wallpaper wood flooring, painted walls, acoustic ceiling, etc. Makes all of your DIY home projects easier such as mounting your TV, bathroom cabinet, photo frame, garage racks etc.
• 🔨 Comfortable Ergonomic Design: the ergonomic design means you can hold the wall scanner in your hand comfortably. Strong grip let you hold the electric stud finder tightly & keep it moving correctly to get more accurate results. Suitable for all types of people
• 🔨 Automatic Calibration & Simple Use: Just press the scan button to start calibrate and it will complete the moment the BEEP sound and screen shows disappear. Calibration before using provides users with maximum reliability & accuracy. If you have any questions in the process of using, feel free let us know

User questions & answers

Question:	Does it work on plaster walls
Answer:	No. This model does not detect electrical wiring. I don't think Franklin has a model for detecting electrical current. However it is the best I have found that can detect wall studs accurately.
Question:	Does this work on ceilings
Answer:	Hello, Sadly, the T6 is not capable of sensing through tile.
Question:	Where is this made
Answer:	Hello, Yes, it tends to be even more accurate with metal studs. Our stud finders sense density, and since metal is more dense than wood, the reading will tend to be more accurate on metal studs. Thank you for your inquiry. Best regards, The Franklin Sensors Team

• This latest stud finder features 5 Modes-- 1/2 inch scan mode locates the center and edges of wood and metal studs up to 1/2 inch deep; 1 inch scan mode locates the center and edges of wood and metal studs up to 1 inch deep; Deep scan locates the center and edges of wood and metal studs up to 1.5inch deep; Metal scan detects metal (Ferrous and Non-Ferrous Metal) up to 2.36 inch deep; AC scan detects live unshielded AC wires up to 2 inch deep.
• Upgraded Smart Sensor: The stud finder adopts intelligent micro-sensor chip with highest sensitivity, which can detect accurately and quickly
• Digital stud detector features large LCD display together with the big sound warning to detect the accurate location of the objects. When find the material, the LCD display will indicate the direction and the intensity of beeping tells whether you are more close to the target. The fast detection saves users time greatly.
• Easy Calibrate: :Press the Scan button to start calibration, the decreasing bars will disappear and buzzer will beep one time and the calibration is completed. Keep tool flat against the wall and do not rock, tilt, or press hard when slowly sliding across the surface being scanned.Once the edge of the stud is picked up, the stud finder will beep. The multi-function stud finder uses state-of-the-art sensor technology to accurately and quickly position rivet wood metal AC wires!
• This stud Indicates the live AC wire in all modes to avoid potentially serious mishaps, let the drill no longer be dangerous. detector quickly locates wood, metal and AC wires hidden in the walls, floors and ceilings of the house. It can work on different wall surfaces, such as lath, wallpaper wood flooring, acoustic ceiling, painted walls, etc. helping you avoid danger when installing TVs, cabinets, garage racks, etc.

User questions & answers

Question:	Will this detect Knob and Tube wires
Answer:	No it will not
Question:	where is this made
Answer:	dont know,does not say on product,did not keep box stud finder was packaged in.
Question:	I can’t find my doorbell transformer. Will this help with the drop ceiling in the basement
Answer:	It pinpoints wiring
Question:	Does this work correctly for you? Mine is ~1.5in off from stud's. Not sure if product sucks or mine's faulty
Answer:	I tried mine first on a wall where I knew where the studs were located already and it correctly identified them.

Product features

An accurate stud finder has great help on DIY home Project, No matter whether you’re hanging a picture, mounting a TV or renovating part of your home.

This stud finder features 5 stud modes to meet your multi detection needs. it is perfect for normal scanning of drywalls and finding joists, beams, and studs in almost all types of stud walls, for example, finding studs on drywalls, plaster wall, finding the beams in the ceiling, floor, locating metal behind walls or other surfaces, even locating metal/screws behind tiles.

Stud Scan

This Stud finder has 3 modes to detect wood and metal up to 1.5inch(38 mm), please detect in Stud Mode first to minimize false positives or find other objects further behind the wall that may not a stud

Metal Stud

The metal Stud can be detected in stud scan and deep stud Scan, you need use mental scan to confirm before reading in Stud Scan or Deep Stud Scan was a wood Stud or Mental Stud

AC Wire Scan

In this mode detect live, unshielded AC wires, electrical wires up to 2 inches (51 mm) deep.

For Safety, in all modes, this wall scanner always detect and indicate the Live AC Wire.

Note: Wire Warning Detection works in both StudScan / DeepScan / MetalScan Modes. The Wire Warning Detection Icon will flash when live, unshielded wires are detected.

Step 1:Calibrate the tool before every scan

Important notice:calibrate it before every scan

Please insert a 9V Battery( not included in package), press Power Button to turn on the tool. put it on the wall where you want to detect, and choose the Scan Mode, then press the Scan Button to start calibration, the decreasing bars will disappear and buzzer will beep one time and the calibration is completed. Note: It is important to wait for calibration to complete(2-3 seconds)

Step 2: Scan the wall

then move the stud finder along the wall slowly, if shake or lift the stud finder accidently, the device needs to re-calibrate.

The narrow on the screen together with the beep signal alter, it means you to find the location of the stud.

Step 3: Find the location of the stud

When the signal bar is full and the beep alarm is loudest, it means you have found the center of an object.Mark it with your pencil.

Then choose the Metal Scan mode to test whether it is a metal. After you confirm that it is not a metal, it means that you found the center of a stud