13 best kreg tape measures

Product description

The Kreg 1/2-Inch Self-Adhesive Measuring Tape fits snugly into the indentation on the topside of the Kreg Top Trak and Heavy Duty Trak aluminum extrusions, but with its self-adhesive backing, the tape can be used virtually anywhere. The metallic tape is highly scuff resistant, can be trimmed to length with household scissors, and reads right-to-left.

From the Manufacturer

This 1/2" wide, self-adhesive measuring tape fits snugly into the indentation on the topside of our Top Trak and Heavy Duty Trak. Metallic tape is highly scuff resistant and can be trimmed to length with a scissors. Be sure to choose the correct tape orientation...left-to-right reading to the right of the saw blade, right-to-left reading to the left of the saw blade.

• Accurate and durable self-adhesive measuring tape
• Interfaces perfectly with the Kreg Top Trak and Heavy-Duty Trak
• Trim to length with household scissors
• Scuff resistant
• Manufacturer's limited 30-day warranty
• Right-to-left reading

User questions & answers

Question:	How hard is it to remove the tape and adhesive residue
Answer:	I never tried 20 files, only tried up to 6 files, but I think this is correct, 30 points per file total 600 points
Question:	Why is this cheaper on the sp website
Answer:	No, it doesn't do multiplication or square foot calculations. This Bosch's most basic laser measure in the GLM series. You can spend more for more full-featured units. Amazon carries them.
Question:	Is this tape right to left reading for the left side of the blade
Answer:	Thank you for your question. To change the unit of measure on the GLM 15, turn off the unit and while unit is off press and hold the button, on the display you will see "unit" and it will be alternating from m to ft/in. Once you get to the unit of measure that you want, let go of the button. It will stay how you have it selected, until you change it. For further assistance, contact us at 1-877-BOSCH99 (1-877-267-2499) from M-F 7a-7p CST.
Question:	How long is it
Answer:	Yes, the measurement starts starts from the rear of the unit. Just place it flush against one side of the frame and you are good to go.

Product features

Kreg 1/2-Inch Self-Adhesive Measuring Tape

• 1/2" (13mm) wide, self-adhesive tape
• Right-to-left reading
• Highly scuff-resistant metallic
• Easily trimmed with scissors
• Compatible with Kreg Top Trak & HD Trak

Product description

This 1/2" wide, self-adhesive measuring tape fits snugly into the indentation on the topside of our Top Trak and Heavy Duty Trak. Metallic tape is highly scuff resistant and can be trimmed to length with a scissors. Be sure to choose the correct tape orientation...left-to-right reading to the right of the saw blade, right-to-left reading to the left of the saw blade.

• 1/2" (13mm) wide, self-adhesive tape
• Left-to-right reading
• Highly scuff-resistant metallic
• Easily trimmed with a scissors
• Compatible with Kreg Top Trak & Heavy-Duty Trak

User questions & answers

Question:	Does this repeat after certain increments or is it 12 continuous feet
Answer:	There is a "Peak Level" button on the front that you press to see the peak level. The peak level is the highest value recorded by the unit and can be reset by pressing the "reset button". Peak level will only record 11 ppm and over. Long term exposure to 9 ppm and over is considered dangerous.
Question:	Is the first 12 inches graduated to 1/32" and the rest to
Answer:	Typically we ship FedEx but we can make arraignments for DHL.
Question:	will this work with Rockler track
Answer:	This is correct
Question:	I want to mount this on a 2 inch circular tube. Will it bend to form to the tube
Answer:	You can create DXF-files on the DISTO

Product features

Kreg KMS7724 12' Self-Adhesive Measuring Tape (Left-Right Reading)

This 1/2" (13mm) wide self-adhesive measuring tape fits snugly into the indentation on the topside of the Kreg Top Trak and the Kreg Heavy-Duty Trak. This metallic tape is highly scuff resistant and can be trimmed to length with scissors.

• 1/2" (13mm) wide self-adhesive tape
• Left-to-right and right-to-left reading options
• Highly scuff-resistant metallic
• Easily trimmed with scissors
• Compatible with Top Trak & HD Trak

Product description

Metric 3.5 meter tape, self adhesive and fits snugly into the indentation on the topside of our Top Trak and Heavy Duty Trak. Metallic tape is highly scuff resistant and can be trimmed to length with scissors.

• 3.5 meter tape
• Metallic, scuff resistant
• Self-Adhesive
• Trim with scissors
• Right to left reading

User questions & answers

Question:	Are inches labeled on this product
Answer:	Carbon monoxide is a gas that will be given off as an incomplete combustion product. One has to make a bunch of assumptions to really answer this question: That there is not a lot of air flow, that the room is not configured or ventilated so there is no mixing, etc. In my opinion, if you put these into a room where there is a chance of combustion (where there is a fireplace or heater, in a kitchen, in a garage) in a normal private residence you will be covered. You can't expect one in the garage to cover the area in the basement or one in an upstairs bedroom to cover a downstairs rec room with a fireplace. One of these in some kind of industrial area of >30,000 square feet would look kind of silly. This is why I bought and installed several. But keep in mind, I am not an expert and if this is a critical issue please check for the specs with the manufacturer.
Question:	What is the product width in mm
Answer:	Unfortunately, I had to replace an old unit different model with this one and my neighbor did it for me and he was forced to drill new holes as this replacement unit holes didn't line up with the old ones. I am sorry I don't know the exact dimensions. I didn't do the installation.
Question:	how wide
Answer:	Misleading answer. The answer saying “Does this detect propane?” And the answer was “No, only carbon monoxide. This is from www.propane101.com. Carbon Monoxide (CO) is responsible for almost 25% of all propane related fatalities. Carbon Monoxide is the product of incomplete gas combustion often because appliances are improperly adjusted. Properly functioning propane appliances will produce what is called an "ideal burn" during combustion and present no danger of Carbon Monoxide poisoning. Carbon Monoxide poisoning can lead to severe injury and even death.

Product description

Features a self-adhesive backing and fits into the indentation on the top side of the Kreg Top Trak and Heavy Duty Trak. Metallic tape is scratch resistant and can be trimmed to length with scissors.

• Features self-adhesive backing
• Fits into indentation on top side of Kreg Top Trak and Heavy Duty Trak
• Scratch resistant metallic tape can be trimmed to length
• Left to right reading
• Size: 12.7 mm (1/2 inch) wide

Product description

1/2" wide self-adhesive measuring tape fits snugly into the indentation on the topside of Top Trak and Heavy Duty Trak. Metallic tape is highly scuff resistant and can be trimmed to length with scissors. Be sure to choose the correct tape orientation; left-to-right reading to the right of the saw blade, right-to-left reading to the left of the saw blade.

• 1/2" wide
• Reads left to right
• 3.5m in length
• Self-adhesive

User questions & answers

Question:	How long is it
Answer:	Hello Peter,Yes, this tape is meant to be used on the left side of the blade. Hope that helps!
Question:	will this tape rust
Answer:	Hello, The tape is twelve feet long. Thanks!
Question:	Is this tape mm or inches
Answer:	We just had a model CO600 from 2013 sound its end of life alarm, so nearly 8 years on the previous model.

Product description

Metric 3.5 meter tape, self adhesive and fits snugly into the indentation on the topside of our Top Trak and Heavy Duty Trak. Metallic tape is highly scuff resistant and can be trimmed to length with scissors.

• 3.5 meter tape
• Metallic, scuff resistant
• Self-Adhesive
• Trim with scissors
• Left to right reading

User questions & answers

Question:	how wide is this tape
Answer:	Hello, I am not sure exactly how you are planning to use it on the 2" tubing, but I do think that it is flexible enough to conform to the 2" tubing. Thanks!
Question:	Are the centimeter markings continuous. In other words, at the 100 cm mark, does it continue to 101, 102, 103, etc. up to 350 cm
Answer:	just use an citris adhesive removal or lacquer thinner.
Question:	la cinta esta en centimetros o pulgadas
Answer:	What's the sp website. I need to buy 2 of these cheaper if I can. Thanks for reply

Product description

Our patented Swing Stop easily sets the distance between the end of the board and the saw blade for amazing cutting accuracy and repeatability. The curved design of the Swing Stop allows a board to bypass the stop automatically by simply sliding the board into the stop’s face. The Swing Stop features an adjustable lens cursor much lick that found on a high-quality table saw rip fence that can be “zeroed out” to assure pinpoint accuracy.

• - Quickly and accurately sets the distance between the end of the board and the saw blade
• - Allows for amazing accuracy and repeatability when cutting boards to length
• - Uniquely designed curved face allows stop to swing out of the way when not in use

User questions & answers

Question:	Does this fit a Dewalt 715 miter saw
Answer:	Hello, The tape is 1/2" wide. Thank You, Billy H Kreg Tech Support.
Question:	Is the cursor adjustable like on a table saw fence
Answer:	Hello, It is 12 continuous feet. Thanks!
Question:	Does this stop work with the extrusion used for the Band Saw Fence
Answer:	It is 1/16" all the way through.
Question:	will this fit an Incra miter gauge
Answer:	It's just a self adhesive tape measure that is 1/2" wide. So if the track you're using is at least 1/2" wide it should work fine.

Product features

Kreg Standard Swing Stop

• Add repeatable accuracy to your miter saw, band saw, table saw fence, router table, and more with this versatile Swing Stop. It holds your desired measurement precisely, and swings out of the way easily when you want to cut without it.
• The Swing Stop features a precision lens cursor with a hairline indicator that allows you to set dimensions exactly. Plus, the cursor is adjustable so you can easily fine tune the Swing Stop to your tool.
• When you want to use the Swing Stop, it stays where you set it thanks to its rugged aluminum construction and high-quality bushings that prevent deflection. When you want the Stop out of the way, simply swing it up or slide your board into the front of the curved foot, and the Swing Stop will pop up out of the way for an unobstructed cut. The foot also has a small breakaway section that allows you to modify it easily to work on a fence that has an auxiliary face.

Product description

Fastcap Self-Adhesive 16' Measuring Tape Reversible Left or Right Read

• Left and right read in one tape
• 16' long or cut in half for 8' on either side
• SpeedTape – ultra strong adhesive
• Standard measurements

User questions & answers

Question:	would this tape lie flat enough for use on a table saw fence rail
Answer:	Not if kept inside. Plus only if the finish is scratched, allowing moisture to penetrate the finish.
Question:	What material is the rule made of? Is it metal or plastic film? What is the thickness of the material
Answer:	Kreg sells both, but the ones I've used/use are in inches. Remember to specify measures from the left to right or reverse, right to left.
Question:	does the tape read one continuous meassurement of 0 -12' or is it broken into smaller "sections" such as 2 - 0-6' readings
Answer:	The tape is labeled in metric, and will measure in centimeters, up to 3.5 Meters. It does not have inches labeled.
Question:	How wide is it
Answer:	Hello, The width of this tape is 12.7mm. Thank you, Kreg Tech Support

Product description

Komelon F12 12-Foot Stick and Measure Flat Tape Measure

From the Manufacturer

The Stick and Measure Flat Tape Measure is a 12-Foot by 1/2-Inch steel tape measure blade that features a strong adhesive backing. It can be applied to any clean flat surface and will stay in place indefinitely. This tape can be cut to length and is perfect for multiple applications such as sewing tables, work benches, as height gauging tape, on table saws, shipping tables or fishing boats.

• 12-Foot by 1/2-Inch Steel Blade
• Self Adhesive Back
• Can be cut to desired length
• Package Dimension : 17.78 cms L x 11.43 cms W x 2.03 cms H

User questions & answers

Question:	is this tape work on saltwater boat to measures the fish
Answer:	The Tapes are 1/2" wide.
Question:	Is this in feet and inches, or just inches? I am looking for just inches
Answer:	Yes. La numeración continúa tal como lo describes 100, 101, 102 .... 200, 201, 202 etc
Question:	does this repeat every 12 inches or run through to 12 feet
Answer:	Está en centímetros.
Question:	is this a right to left or left to right tape it is for my table saw
Answer:	You can order different lengths, 3', 6', etc...

• Material: 100% eco-friendly material.
• Tape size: 61cm / 24 inches
• Waterproof, clear markings, easy to clean, easy to use.
• Reed left to right
• Adhesive Backed Tape Measure--Reads right to left

User questions & answers

Question:	how wide is the inch tape
Answer:	I built a mitre fence using the Kregel track for the swing stop. For my woodworking putting it on the saw wouldn’t work for me.
Question:	Do they offer a right to left version of this tape
Answer:	The question is not clear to me, but if your asking if this system could be installed on a table saw fence, I would yes with some work. One problem that might arise would be that the swing arm might not be long enough to reach the table top when dropped into place so might be ineffective for thinner materials.
Question:	Will it stick to plastic
Answer:	The Kreg Standard Swing Stop will work with the fence on the Kreg Bandsaw Fence.
Question:	How wide is it
Answer:	Yes the Kreg Swing Stop will fit into the T slot on the miter gauge's fence. However, the T slot is located on the front of the fence and the Swing Stop is really designed to be affixed to a T slot on the top. As a result, the stop's foot rests on the saw's table top several inches away from the fence. If the Swing Stop is being used as a "stop", this shouldn't be a problem if the board being cut is at least 3 inches (and preferably 3 1/4") wide.

Product features

61cm 24'' Adhesive Tape Measure

• Convenience: We can stick it anywhere.
• Durable: They're not only waterproof but also not afraid of sun exposure
• A variety of styles: 1.start from left to right 2.start from right to left

Silver Adhesive Tape Measure

Silver Adhesive Tape Measure

Golden Adhesive Tape Measure

Tips:

1. Please wipe clean with a damp cloth before sticking.

2. Paste it after drying.

3. Start by sticking from one end and then slowly pressing it to the other end, in order to reduce bubble generation.

Product description

From The Manufacturer: The Kreg Multi-Mark Is An Incredibly Handy Multi-Purpose Marking And Measuring Tool, Perfect For A Wide Variety Of Household And Jobsite Applications. The Multi-Mark Features Three Different Scale Configurations, A Built-In Level, A Handy 3/16” Reveal Gauge, And Much More… Whether You Need To Transfer A Measurement For That Last Ceramic Tile, Layout Some Mitered Corners, Or Just Straighten A Few Simple Picture Frames, The Multi-Mark Is The Only Tool You’Ll Need To Get The Job Done. Features: , 3 Scale Configurations , Imperial And Metric Scale , Built-In 3/16" Reveal Gauge , Torpedo Level , Durable And Compact Design.

From the Manufacturer

The Kreg multi-mark is an incredibly handy multi-purpose marking and measuring tool, perfect for a wide variety of household and jobsite applications. The multi-mark features three different scale configurations, a built-in level, a handy 3/16-Inch reveal gauge. With this tool you can layout mitered corners, set 3/16-Inch reveals, transfer measurements , align/square your projects, set bit/blade heights , layout wall studs, use as a basic rule, marking for layout and use as a simple level.

• From the manufacturer: The Kreg Multi-Mark is an incredibly handy multi-purpose marking
• The Multi-Mark features three different scale configurations, a built-in level, a handy 3/16” reveal gauge
• Item is manufactured in United States
• Wide variety of measuring and marking functions
• 3 Unique scale positions
• 3/16-Inch offset for door trim
• Cumulative scale for transferring measurements
• Perfect for general layout

User questions & answers

Question:	Is it metal or plastic
Answer:	No, the DB210 can use the Micro and Heavy-Duty bits but not the plug cutters.Ben BolluytKreg Tech Support
Question:	Is the marking tool in imperical and metric
Answer:	The Kreg Foreman will only make 15 degree angled pocket-holes in material thicknesses from 1/2" to 1 1/2".
Question:	does it have a marking gauge for joinery
Answer:	the kerf is 1/4" also known as cutting length on this bit. the cutting depth is 1/2".
Question:	Is this in any way an angle finder too
Answer:	I would hazard a guess that if you want to cut deeper you would have to use a tool (bit) with a larger diameter cutting blade.

Product features

Multi-Mark

Product description

4 Pieces self-adhesive measuring tape sticky steel ruler tape 1/2 x 40 inch, 1 m left-right reading



Simple to apply:

You can use scissors to cut the adhesive metal tape measure to the size you need, then simply peel and paste.



Widely applicable:

Sticky measure ruler with adhesive backing can be stuck to almost all working surfaces, your workbench, sawing machine, drawing table or any other place for easy measurement.



Specifications:

Material: steel

Color: as picture shown

Size:

Length: 1 m/ 40 inch

Width: 1/2 inch

Scale: cm and inch



Package contains:

4 x Self-adhesive measuring tapes



Note:

Please allow a little error on the size due to manual measurement.

• Reliable material: our sticky measuring tapes are made of quality precision steel for durability and long-lasting use
• Features: the self-adhesive steel measuring tape reads left to right; Length: 1 m/ 40 inch; Width: 1/2 inch; Scale: cm and inch
• Wide application: sticky measure ruler with adhesive backing can be stuck to almost all working surfaces, your workbench, sawing machine, drawing table or any other place for easy measurement
• Easy to use: you can use scissors to cut the adhesive metal tape measure to the size you need, then simply peel and paste
• Package includes: 4 pieces of 1 meter self-adhesive steel measuring ruler tape, enough quantity to meet your different needs

User questions & answers

Question:	Will it stick to the plastic folding tables
Answer:	This a flexible metal rule. It is approximately 1/16" thick.
Question:	What is the accuracy rating of Weewooday-Measuring Tape-01 tape measure
Answer:	0-16'
Question:	anyone know if this works well with kreg top track on a cross cut sled
Answer:	7/8" wide

Product description

Steel precision tape measure that sticks to almost any surface. Lies flat, cuts to size with scissors. Useful on a work bench, butcher block, drafting table, radial arm saw Whenever repetitive measurements are required.

• Starrett Measure Stix provides a tape measure that sticks to almost any work surface for convenient, at a glance measurements.
• High quality precision steel rule is flat with permanent adhesive back
• Cut to size with scissors
• Mount on workbenches, saw tables, drafting tables, etc.
• 1/2" width has an inch/foot face (1/16" divisions)
• Produced with permanent adhesive back that sticks to almost any work surface for convenient, at-a-glance measurements
• Mounts on work benches, saw tables, drafting tables, etc.

User questions & answers

Question:	Is this tape white like most of the other starrett tapes
Answer:	It is in linear inches with the feet marked above it. In other words at 5 feet it reads 60 inches. So the inches do not repeat 1-12.
Question:	Why isn't this left to right reading tape priced at $6.24 with prime shipping like starrett measure stix sm412wrl
Answer:	Consecutive feet are marked and the inches are cumulative so 4ft shows 48 inches and 5ft shows 60 and so forth.
Question:	why does is say 3/4 when it is only 1/2 inch
Answer:	It is numbered left to right
Question:	Does this product come in either reading "left to right" or "right to left". I need both ways for a cut off saw. If not, where can I purchase them
Answer:	Yes. That's what I'm using it on. Clean the fence with solvent before you apply this tape.

Product features

Starrett Measure Stix

Measure Stix are manufactured with high quality precision steel for extended service use. It is produced with a permanent adhesive backing that will stick to almost any work surface providing convenient, at-a-glance measurements. They can be mounted on work benches, saw tables, drafting tables, and more. Left to right or right to left print orientation.

Quality First

Manufactured of high quality precision steel for extended service use.

Adhesive Back

Produced with permanent adhesive back that sticks to almost any work surface for convenient, at-a-glance measurements.

Mounting Capability

Mounts on work benches, saw tables, drafting tables, and more.