13 best dayton outdoor heaters

Product description

Product Details: Electric Utility Heater, Heater Voltage 208/240VAC, 5.0/3.3 3.7/2.5 kW, 17065/11372, 12800, 8533 BtuH, 1 Electric Heater Phase, 20.8/13.8 17.8/12.0 Amps AC, 60 Hz, Temp. Rise 71 Degrees F, Air Flow 210 cfm, Width 21 In., Depth 8 In., Height 16 In., Housing Material Steel, Heater Housing Finish Painted, Features Thermostat, Totally Enclosed Permanently Lubricated Fan Motor, High/Low Heat Selector Switch, Fan Only Switch

• Features: Thermostat
• Warranty (Years): 1
• Height: 16"
• Width: 21"
• Depth: 8"

User questions & answers

Product description

Lightweight heater requires no electricity for operation, heats open areas quickly, and is for use in well-ventilated or outdoor areas. Features adjustable heat setting from Low to High, flame safety system, and piezo ignition. Gas tank not included. Portable Gas Heater, LP, 50000/200000 BtuH This product contains a chemical that is regulated under California Proposition 65. Warning: This product contains a chemical known to the State of California to cause cancer. Warning: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm. -

User questions & answers

Product description

This tubular gas fired direct spark propeller unit heater is designed to be suspended within the space to be heated. It operates on NG or LP gas with the included conversion kit, and is field-convertible for separated combustion with an approved vent kit. Multitapped rails allow multiple O.C. distances. ETL Certified in accordance with both Categories I and III venting requirements. Approved for installation in residential garage, commercial, and industrial environments. 24V thermostat required; available separately. Power venting allows horizontal venting through side walls Tubular heat exchanger and single burner designNote: For altitudes above 2000 ft., consult owner's manual prior to installation for proper adjustments. Use single- or double-wall vent pipe when venting vertically, or single-wall pipe when venting horizontally. This heater is not to be connected to ductwork. Gas Unit Heater, NG/LP, 75000 BtuH, 30" W

• USA

Product description

Ideal for residential garage and workshop areas, this heater features automatic thermal protection and a built-in thermostat. The aluminized paint finish provides corrosion resistance. Sspnd Elct Wl/Ceil Heatr, 12-1/2"H, 240V

• USA

Product description

Dynamically balanced blower mounts in any position and operates with minimal noise and vibration, to maintain cfm at higher static pressures. Open motor has cast-aluminum end shields for greater heat dissipation, resulting in less downtime and longer service life. Ball bearings. Not for use with speed controllers.

User questions & answers

Product features

Dayton Rectangular Permanent Split Capacitor OEM Specialty Blower

Dynamically balanced blower mounts in any position and operates with minimal noise and vibration, to maintain CFM at higher static pressures. Open motor has cast-aluminum end shields for greater heat dissipation, resulting in less downtime and longer service life. Ball bearings. Not for use with speed controllers.

Dayton PSC and Shaded Pole Blowers

Many jurisdictions and localities have codes and regulations governing sales, construction, installation, and/or use of products for certain purposes, which may vary from those in neighboring areas. While Dayton attempts to assure that its products comply with such codes, it cannot guarantee compliance, and cannot be responsible for how the product is installed or used. Before purchase and use of a product, review the product applications, and all applicable national and local codes and regulations, and be sure that the product, installation, and use will comply with them.

OEM Blowers

The blowers are exact replacements for many OEM blowers with the same physical footprint. Forward curve wheels driven by Dayton motors are rated for continuous duty with all-position mount. These units incorporate balanced ball or sleeve-bearing motors with cast aluminum end shields. This provides greater heat dissipation and protection, reducing down time due to component failure and accidental damage. Direct drive blower wheels are dynamically balanced to reduce noise and vibration and to maintain CFM at higher static pressures.

Product description

Direct OEM replacement blower mounts in any position and maintains cfm at higher static pressures. Open motors with cast-aluminum end shields dissipate heat to help reduce downtime and extend service life. Ball bearings. Not for use with speed controllers.

• 115 vac
• Oem specialty blower
• Ul recognized us and canada (E47479), ce
• Includes discharge mounting flange and inlet cover

User questions & answers

Product features

Dayton Rectangular Permanent Split Capacitor OEM Specialty Blower

Dynamically balanced blower mounts in any position and operates with minimal noise and vibration, to maintain CFM at higher static pressures. Open motor has cast-aluminum end shields for greater heat dissipation, resulting in less downtime and longer service life. Ball bearings. Not for use with speed controllers.

Dayton PSC and Shaded Pole Blowers

Many jurisdictions and localities have codes and regulations governing sales, construction, installation, and/or use of products for certain purposes, which may vary from those in neighboring areas. While Dayton attempts to assure that its products comply with such codes, it cannot guarantee compliance, and cannot be responsible for how the product is installed or used. Before purchase and use of a product, review the product applications, and all applicable national and local codes and regulations, and be sure that the product, installation, and use will comply with them.

OEM Blowers

The blowers are exact replacements for many OEM blowers with the same physical footprint. Forward curve wheels driven by Dayton motors are rated for continuous duty with all-position mount. These units incorporate balanced ball or sleeve-bearing motors with cast aluminum end shields. This provides greater heat dissipation and protection, reducing down time due to component failure and accidental damage. Direct drive blower wheels are dynamically balanced to reduce noise and vibration and to maintain CFM at higher static pressures.

Product description

Compact modular heater features high-intensity ceramic burner, highly polished aluminum reflector, and water-resistant circuitry. Commercial Infrared Heater, NG, 90, 000 This product contains a chemical that is regulated under California Proposition 65. Warning: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm. -

• USA
• Banned in MA

Product description

Good for restaurant patios, entryways, porches, mezzanines, vestibules, etc., and outdoor residential use. Uniform infrared pattern quickly heats people, objects, and the surrounding air. Wind- and rain-protected design with grille. Constructed with water-resistant electrical components.Note: Winds in excess of 5 mph may require additional heaters to obtain desired comfort levels. Infrared Patio Heater, NG

• USA

Product description

OEM Blower, Outlet Shape Rectangular, With/Without Flange With Flange, Wheel Dia. 2-15/16", Wheel Width 1-7/8", CFM @ 0.000-In. SP 30, CFM @ 0.100-In. SP 25, CFM @ 0.200-In. SP 21, CFM @ 0.300-In. SP 16.5, CFM @ 0.400-In. SP 3, Voltage 115, Hz 60, Phase 1, Full Load Amps 0.51, RPM 3233, Bearing Type Ball, Motor Type Shaded Pole, Motor Enclosure Open, Motor Insulation Class B, Thermal Protection Auto, Lead Length 13", Conduit Box No, Max. Ambient Temp. 104 Degrees F, Max. Inlet Temp. 104 Degrees F, Inlet Dia. 2-9/16", Outlet Height 1-5/8", Outlet Width 1-9/16", Overall Height 4-5/8", Overall Width 3-1/2", Overall Depth 4-1/2", Wheel Type Forward Curve, Drive Type Direct, Mounting Position All Position, Housing Finish Enamel, Housing Material Rolled Steel, Housing Color Gray, Agency Compliance UL Recognized US and Canada (E47479), CE, Replaces 4C760, Includes Discharge Mounting Flange.WARNING: California ResidentsThis product can expose you to chemicals including Styrene, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

User questions & answers

Product description

Portable standard electric jobsite and garage heaters have a tubular heating element for high-efficiency heating and use fan-forced air to distribute heat throughout the space. These heaters are protected with an internal thermal cutout, which shuts off the heater in the event of overheating and can be manually reset when the temperature returns to normal. These heaters have a unit-mounted thermostat.Portable electric jobsite and garage heaters provide warmth to jobsites and garages. They don't give off fumes, so they don't require venting. They're more powerful than office heaters to safely warm workers in cold conditions. They can be plugged into an outlet that corresponds to their voltage rating. These units have built-in temperature controls. Prtbl Elct Job/Garage Heatr, 15" L, 120V This product contains a chemical that is regulated under California Proposition 65. Warning: This product contains a chemical known to the State of California to cause cancer. Warning: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm. -

User questions & answers

Product description

Infrared Gas Tube Heater Indoor Outdoor Gas Type NG 50000 BtuH Length 260 In. Width 18-1/8 In. Height 8-1/2 In. Radiant Pipe 20 ft. Heater Voltage 120VAC 60 Hz 4.8 Amps AC Min Mounting Height 10 ft. Clearance to Combustibles (In.) Behind 1-45 Deg. 8 Clearance to Combustibles (In.) Below 0 Deg. 47 Clearance to Combustibles (In.) Front 1-45 Deg. 39 Clearance to Combustibles (In.) Sides 0 Deg. 9 Clearance to Combustibles (In.) Top 0 Deg. 6

Product description

PSC Blower, 2 Speed, Forward Curve, Direct Drive, Wheel Dia 5 1/8 In, CFM @ 0.000-In SP 428/293, Voltage 115, 60 Hz, Single Phase, Full Load Amps 1.1/0.85, RPM 1500/1085, Max Inlet Temp 104 Deg F, Overall Height 9 3/8 In, Overall Width 9 1/4 In, Overall Depth 8 9/16 In, Includes Discharge Mounting Flange.

User questions & answers