4 best vortex optics night vision scopes

• The Spitfire HD Gen II 3x prism scope offers ultra-fast target acquisition while still being usable even without illumination. The streamlined look and flush mount turret design makes for a smaller, lighter, and faster optic.
• The updated optical design and fully multi-coated lenses provide improved resolution, and cuts chromatic aberration. The prism design and etched reticle solve the distortion problems for users plagued by astigmatism.
• The BDC-4 reticle is built for rapid target and acquisition holdovers out to 650 yards while offering 12 brightness settings; the lowest two settings being ultra-low for use with night-vision equipment.
• The Spitfire HD Gen II prism sight can be mounted at two heights, lower 1/3 co-witness or a “low” mount option.
• Nitrogen purged, the Spitfire HD Gen II is waterproof, shockproof and fogproof; standing up to whatever you throw at it.

User questions & answers

Question:	Does this come with the spring loaded flip lens caps like the original 1x
Answer:	No it has rubber caps that are attached to the battery cover.
Question:	Is this reticle for 300 black out, 5.56, or
Answer:	I presume you are asking about the 3x Gen II prism scope, not the Spitfire red dot. From the Vortex literature, it appears that the BDC was designed for the 5.56/.223 cartridge, since that is the only cartridge mentioned by Vortex.

Product features

Powering Up/Illumination

Press the up (+) or down (-) button to turn on the illumination. Press and hold the up (+) or down (-) button for three seconds to turn illumination off.

To adjust the illumination:

The Spitfire HD Gen II sight offers 12 brightness settings, the lowest two settings being ultra-low for use with night-vision equipment. Adjust the brightness by tapping the up (+) or down (-) button. The sight will return to the last used brightness setting when turned on.

Reticle Focus

1. After mounting the sight, point the sight at a blank white wall or up at the sky.

2. Starting with the fast-focus eyepiece all the way in, glance through the optic. If the reticle is not in focus, rotate the eyepiece out counter clockwise slightly, and look through the optic again.

3. Repeat this process until the reticle is in sharp focus.

Turret Adjustments

The Spitfire HD Gen II features dial adjustments and a reticle scaled in Minute of Angle – MOA. 1 MOA will always subtend 1.047" for each 100 yards of distance. Your optic will have 1 MOA clicks. Each click moves your point of impact roughly 1" at 100 yards, and a 1/4" at 25 yards.

To adjust the settings:

• Turn the elevation or windage dial in the appropriate direction as indicated by the arrows. Rotate the dials in the direction you wish the bullet’s point of impact to go.

Mounting

1. Loosen the base crossbolts and attach the Spitfire HD Gen II to the rail/base with the illumination dials facing toward the rifle’s left.

2. Make sure the recoil lugs are solidly seated in the base groove by pushing the optic forward, towards the end of the muzzle.

3. Be sure the base clamp is hooked around the outside of the rail/base. Torque base screws to 20-22 in-lbs.

Mounting Micro Red Dot Sights (MRDS) - (5x Models Only)

1. Remove the MRDS cover plate by removing the two screws. Retain screws for use with MRDS cover plate.

2. If the Weaver/Picatinny mount is attached to the MRDS, remove the Weaver/Picatinny mount.

3. Install the MRDS to the platform. Install the respective screws for the Viper or Venom and torque to 10-12 in-lbs with blue Loctite.

Product description

Rifle Scope

• The Diamondback Tactical First Focal Plane 4-16x44 stands at the intersection of precision and value, delivering an impressive array of features and performance.
• Extra-low dispersion glass and fully multi-coated lenses transmit a crisp, bright sight picture. The first focal plane, glass-etched reticle keep subtensions accurate throughout the 4x zoom range.
• The precision-glide erector system uses premium components in the zoom lens to ensure smooth magnification changes under the harshest conditions.
• Exposed tactical turrets and a side parallax knob give shooters the tools needed for long distance precision shooting. The fast focus eyepiece allows quick and easy reticle focusing.
• The single piece 30mm tube is shockproof, ruggedly built to withstand recoil and impacts. Strong o-ring seals and nitrogen purging guarantee waterproof and fogproof performance.

User questions & answers

Question:	What comes in the 6-24-50 scope box
Answer:	I purchased the 4-16x44. That package included scope, sun shade and a glass cleaning cloth.
Question:	Best scope ring height for bolt action use
Answer:	My custom 700 Rem,.Bolt Gun. 308 Palma chambered @155 grains. General Plasterized Hart barreled Beast uses a 20 moa Leupold mount .... With ....Medium Height... vortex rings...... For my Hog Killin 56mm. Vortex
Question:	Is the scope specifically made for a certain caliber
Answer:	No, it’s either Designed to work with Minutes of angle or mill radians the multiplayer for minutes of angle aka MOA is 1.047 or roughly 1 inch at 100 yds and with the 1/4 MOA turrets that’s roughly 1/4” at 100 yds both in elevation (up and down) and Windage (left to right) milliradian aka MRAD one milliradian is 3.6” at one hundred yards and the value of each click is 1/10th of a mil so each 1/10th is .36 of one inch for people new to scopes the MOA is usually easier to use however both measurements are angular so at 200 yds one MRAD is 7.2” and 1 MOA IS 2.094” to answer you’re question further the answer is no they are not Bullet drop compensation Reticles aka BDC but there is great information out there on how to better use you’re Reticle for range finding and instead of adjusting the turrets instead use the reticle like a BDC and use hold over values
Question:	Does anyone have any data to support using this on a win 300 mag platform? curious if it can handle the recoil forces. thanks
Answer:	I use Talley mounts and have it on a Remington Sendero in 300 win mag continues to hold zero after 500 rounds

Product description

The incredible features of the AMG UH-1 Gen II are matched only by its tough, tenacious performance. Absolute zero image distortion and an impressive sight picture with unobstructed view ensure rapid, instinctual target acquisition. The XR Plus fully multicoated windows and holographic elements are built to last and promote optimal light transmission. All sensitive components are protected in the sights base increasing durability, while eliminating the need for an obstructive secondary shroud.

• The AMG UH-1 Gen II is a close-quarters solution built for military and law enforcement shooters, offering an incredibly fast holographic display to conquer any situation, now with four night-vision compatible settings and a dedicated night-vision button.
• With the UH-1 Gen II, you get an improved sight picture through the enlarged viewing window, making target acquisition even faster, and easy battery changes with the toolless battery cover, plus a lighter load at just 11 ounces.
• The lightning-quick EBR-CQB reticle is designed to dominate in close, and our FHQ technology virtually eliminates stray light emissions for zero forward signature.
• An integrated, quick-release mount makes the sight easy to install and puts the optic at lower 1/3 cowitness height on either Weaver or Picatinny rails. Rugged construction withstands recoil and impact.
• Ultra-hard, scratch-resistantant ArmorTek coating protects exterior lenses from scratches, oil and dirt. O-ring seals help to provide waterproof and fogproof performance in the field.

User questions & answers

Question:	What's the Waterproof rating? Ipx7? Ipx
Answer:	Yes it comes with the chain
Question:	What is the size of the sight window (e.g. lens)? i'd like to compare to the eotech xps2 which has a 21.6mm window (0.85 inches
Answer:	Hey Kala...good idea using the bike grips...I have been a bit annoyed re the foam "slip"issues, the bike grips should eliminate the problem... good job!
Question:	No shake and wake
Answer:	Dear Sir/Madam,Thank you for your interest in our product and contacting us.The length of the rope is 1.1 meters (43.3 inches).We hope that our response answers your inquiry. If there is anything unclear, please don't hesitate to contact us.Very best regards.
Question:	Can someone please post a picture on how it looks in NV mode
Answer:	Use tennis tape, just as good and lasts longer.

Product features

Night-Vision Button

To set the UH-1 to night-vision mode, press and hold the NV button. Adjust the illumination setting to your preferred brightness. Press and hold the NV button to return to the last daylight illumination setting. The UH-1 will return to the last NV setting used the next time you return to NV mode.

Note: When in night-vision mode, the reticle will only be visible with the use of a night-vision unit.

Windage & Elevation

Use a coin or flat-head item to turn the dials to adjust for point of aim. For both dials, one click will change the point of aim approximately ½ MOA when zeroing. One full rotation of either dial will change the point of aim approximately 16.5 MOA—approximately 8.25" at 50 yards or 16.5" at 100 yards when zeroing.

Note: When adjusting, you may encounter increased resistance. This means you’ve reached the end of the adjustment range and should not turn the dial more.

Battery

One CR123A battery powers the UH-1. To remove the tool-less battery cap, flip up the tab and turn the cap counterclockwise. Install the battery with the positve (+) end going into the unit. Replace the battery cap.

The UH-1 will automatically shut off after 14 hours if no button is pressed. The 14-hour Auto Shutoff feature can be disabled.

Integrated Quick-Release Mount

1. To open the mount, depress the lock button and swing the quick-release mount lever 90 degrees to the open position.

2. Position the UH-1 down onto the rail at desired location. Place the lever side onto the rail first, then rotate the unit so it is flush on the rail. Apply forward (towards the muzzle) pressure on the unit. Move mount lever back to closed position.

3. Check lever closing tension. Lever should close with moderate pressure using thumb or finger. It should not require excess force to close. If lever won’t close, closes with excess force, or seems extremely easy to close with little or no tension, proceed to step 4.

4. To adjust the tension, move the lever back to the open position. Using a flat head screwdriver or similar device, turn the adjustment nut left or right to loosen or tighten. Make small adjustments of one or two clicks, then check lever closing tension. It may be necessary to repeat this process a few times until proper tension is achieved.

Product description

When situations demand split-second target acquisition and maximum field of view, mount up the StrikeFire II and shoot—both eyes open. Feature-rich, versatile and reliable, the StrikeFire II is a great choice for shooters who want a quality red dot sight. Available in multiple reticle colors.

• The Strikefire II Red/Green Dot is a rugged, reliable red dot sight that is at home in a variety of shooting applications. It allows the shooter to operate between two dot colors and ten brightness settings to easily adjust for changing conditions
• Fully multi-coated lenses provide a clean and bright, unobscured point of view. Unlimited eye relief allows for rapid target acquisition. Max Elevation Adjustment- 100 MOA. Max Windage Adjustment- 100 MOA
• The single-piece chasis is compact and lightweight but still delivers shockproof performance withstanding both recoil and impact. Nitrogen purging and o-ring seals ensure fogproof and waterproof performance
• An offset cantilever mount is provided; allowing you to move the sight forward to be used in conjunction with a magnifier and backup iron sights all on the same rail
• With aesthetics and functionality in mind, the power controls are at the rear of the Strikefire for easy access. The Strikefire II runs off a CR2 battery.

User questions & answers

Question:	Will this fit on my AK with the mount that it comes with
Answer:	It is supposed to be BTR-2, but I received a simple 3 dot drop down instead.
Question:	What's the difference between this the 501 and the 505. Does this come with the Cantilever Mount
Answer:	Yes its included
Question:	What is the moa on this
Answer:	Yes, good for close and medium range
Question:	does this have the tall mount compatible to the AR or the short mount for rifles
Answer:	No

Product features

StrikeFire II Red/Green Dot Sight (SF-RG-501)

When situations demand split-second target acquisition and maximum field of view, mount up the StrikeFire II and shoot—both eyes open. Feature-rich, versatile and reliable, the StrikeFire II is a great choice for shooters who want a quality red dot sight. Features sleek rear-facing controls for power on/off and easy adjustment of ten dot intensity levels—lowest two settings are night-vision compatible. Automatically returns to the last dot intensity used when powered up. The 30mm aluminum alloy chassis provides extra-high recoil rating and is waterproof and fogproof. Strike fast!

The lower 1/3 co-witness cantilever mount model is ideal for rifle platforms, positioning the optic bore center 40 mm above the base surface.

Red/Green Dot Reticle

The 4 MOA Red/Green Dot is ideal for situations that demand split-second target acquisition. Choose among ten variable illumination settings—the lowest two settings are night-vision compatible.

The key thing to remember when shooting with the StrikeFire II red dot is to keep both your eyes open! Shooting with both eyes open allows you to take full advantage of your peripheral vision to get on target very quickly. Eye placement is not critical. As long as you can see the dot, you’ll hit your target!

Windage and Elevation Adjustments

The StrikeFire II red dot incorporates elevation and windage dials with audible clicks. Each small click will move the point-of-impact 1/2 Minute of Angle (MOA). 1/2 MOA will correspond to 1/2 inch at 100 yards, 1/4 inch at 50 yards, 1/8 inch at 25 yards, etc.

Adjust the elevation and windage settings:

1. Remove the dial covers.

2. Use the raised bar on the dial cover, a coin or screw driver to make the adjustments.

3. Turn the adjustment dial in the appropriate direction as indicated by the arrow on the dial. Move the dial in the direction you wish the bullet’s point-of-impact to change.

Mounting the StrikeFire II

To get the best results from your StrikeFire II red dot, proper mounting is essential and, although not difficult, the correct steps must be followed. Your firearm will need to be equipped with a Picatinny or Weaver style rail/base.

To attach the included cantilever ring mount:

1. Attach the lower part of the cantilever ring mount to the rail/base and make sure this is solidly seated in the base groove. To prevent recoil injury, position the ring so that you have at least four inches of eye relief.

2. Be sure the base clamp is hooked around the outside of the rail/base. Press downward and forward toward the muzzle. Then, firmly tighten the base clamp hex nut.

3. Place the StrikeFire II on the lower part of the cantilever ring mount with the adjustment control buttons facing the shooter. Tighten ring cap screws evenly until all are snug—use caution so as not to over-tighten. Once the screws are tightened, the StrikeFire II should not move on the rail/base.