12 best fog makers

• ♦ WIDELY USE - AGPtEK fogger machine indoor HS0056 can add a great amount of mist to your pond or water tank to filter the bad smell with ultrasonic technology. You can put the fountain atomizer in your pond, rockery, fish tank, vase, tank, etc. It will create a magical atmosphere. Especially perfect for Halloween and other holidays.
• ♦ WATERPROOF - The ultrasonic foger is waterproof and the length of the power adapter cable is long enough. Ideal for indoor or outdoor fountains, water feature, and office use.
• ♦ ENVIRONMENTAL PROTETION - Our plant humidity fogger can provide large amount of mist. Aerosolized amount≥400mL/H.No heat or chemicals used.
• ◆ EASY TO OPERATE - No heat or chemicals should be used in this led fog machine. This fog machine for fountains is easy to operate, put this water mister in the water and then the mist will appear.
• ♦ SAFE TO USE - The voltage of AGPtEK mist makers is 24V, so it's safe to use.

User questions & answers

Question:	Is there any way to have it not splash as much? Makes puddles in my snake terrarium
Answer:	All you need to do is use a god size jug or jar with a sealable top. On the lid Drill a hole to run the misters wire through, a larger hole half inch or whatever size tube you want to push the fog through. And one more hole that you will run an aquarium air hose through that has an air stone places at the bottom of your jug and air pump hooked up on the outside. After putting your wires and tubes through silicone seal around your drill holes to make your jar air tight. Put the large tube where you want the fog and fire up the air pump and fogger. Since it’s in an Air tight container the bubbles being blown through the air stone will create pressure in the sealed jug. The pressure will push that fog nice and thick ansywhere you want it to go. Have fun everyone !
Question:	Is it strong enough to have a tube attached to it and produce smog through the tube? Not a long tube it would be about 12in
Answer:	Your water level is most likely too low. I have to keep adding more water every couple hours or it doesn't make the mist.
Question:	The one I got doesn't have the water level sensor and after being on for a while it stops making mist and starts flashing just the red light
Answer:	I use it in a five gallon bucket and the mist is so thick I cant see the bucket or water but it only works properly with the float.
Question:	How much volume can the mist generated fill? Looking for something to use in a large cauldron for Halloween
Answer:	Yes

• ♦ WIDELY USE - AGPtEK fountain atomizer can add a great amount of mist to your pond or water tank to filter the bad smell with ultrasonic technology. You can put it in your pond, rockery, fish tank, vase, tank, etc. This fogger machine indoor will create a magical atmosphere. Especially perfect for Halloween and other holidays.
• ♦ WATERPROOF - The ultrasonic foger is waterproof and the length of the power adapter cable is long enough. Ideal for indoor or outdoor fountains, water feature, and office use.
• ♦ ENVIRONMENTAL PROTETION - Our plant humidity fogger can provide large amount of mist. Aerosolized amount≥400mL/H.No heat or chemicals used.
• ♦ SAFETY & EASY TO OPERATE - Put this mini mist maker in the water then the mist appears and the voltage is 24V so it’s safe to use. NOTE: Please DO NOT TOUCH THE WATER when it works.
• ♦ CUSTOMER SUPPORT - We strive to offer superior customer service and technical support. If you have any questions, please don’t hesitate to contact us, we respond email within 24 hours.

User questions & answers

Question:	Will this make enough fog or mist to overflow a 22" X 17" container for a holloween prop
Answer:	I dont know how you are able to get persons name. Maybe try to contact the seller. I just did happy birthday
Question:	Does the mist maker make much/any noise
Answer:	Email the seller they fedex them overnight. It’s ridiculous that they can’t send everything they advertise
Question:	What is the difference between this one and the aluminum one
Answer:	All Monarch Rain Chains work with any Monarch Adapter. The key is to measure your gutter so you buy the correct adapter, Large or Standard. I hope this answers your question.
Question:	how deep can this be placed under water and still produce fog
Answer:	we had to modify it to fit ... my downspout was square-ish and this is definitely not. so truthfully, I can't answer. We had to cut the plastic of the downspout opening to make it work. not a perfect solution, more of a work-around

Product description

Mini Mist Maker, Mister Fogger Water Fountain Pond Fog Machine Atomizer Air Humidifier, Indoor Fountain Mister Foggers

• PULACO Mist Maker can create dense mist for your small pond or water tank in seconds, it is 100% water mist, smelless and colorless, use electro and ultrasonic technology. You can put it in your pond, rockery, fish tank, vase, birdbath, etc. It creates a magical atmosphere.
• Mist maker cable length: 7.0 ft, (3.0 ft attach to adapter, 4.0 ft attach to mist maker)
• 【Easy to use】: Put it in the water then the mist come out and it is 24 V voltage safe design. Install the mist maker under water depth 2-2.8 inches (water level: 0.6inch between mist maker sensor and water surface)
• 【Note】 Ensure the water at high quality, use clean tap water, water quality deterioration may influence the lifetime. Please switch off the power before Movement or maintenance. Mist Maker should be fully submerged in water. Do not put your hands cover above the centre mist while it working, it may causing discomfort. Mist maker can not working continously over 8 hours.

User questions & answers

Question:	so only tap water ?? no needs special water or mineral water or fog maker liquid
Answer:	Yes, just tap water enough.
Question:	Can you keep it one one color
Answer:	No. It goes through all the colors.
Question:	What style plug is this? us or european? i just had to return one that showed a is plug but was actually a european plug
Answer:	I use it in the US, so I’m assuming it’s a US plug.
Question:	if i use it on water can my reptile is drink it ?? or the water is drinkable for other animals on a Pond
Answer:	Yes. I have one for my iguana tank and one for my fire skink. They work great for this.

Product features

Installation:

• 1. Take out the mist maker and AC/DC adaptor, connect the DC plug.
• 2. Install the mist maker under water depth 2-2.8 inches (Best working water level: 0.6inch between mist maker sensor and water surface) and plug-in the adpator.
• 3. There is a cable cap on the power cord, adjustable, thats for prevent mist gathered into water droplets, flows out and affect other devices.

Application

PULACO Mist Maker, using ultrasonic electronic technology to make the water molecules into fog molecules.smelless and colorless. Perfects for being used in your pond, botanical garden, rockery, fishtank, vase, pool.,etc. It will create a magical atmosphere. Easy to operate, put it into the water, then the mist appears. Ideal for indoor or outdoor fountains, water feature, and office use.

• WIDELY USE - SURPRIZON fountain atomizer can add a great amount of mist to your pond or water tank to filter the bad smell with ultrasonic technology. You can put it in your pond, rockery, fish tank, vase, tank, desktop fountain, etc. This fogger machine indoor will create a magical atmosphere. Especially perfect for Halloween and other holidays.
• EASY TO OPERATE - Put this mini mist maker in the water then the mist appears and the voltage is 24V so it’s safe to use. NOTE: Please DO NOT TOUCH THE WATER when it works.
• ENVIRONMENTAL PROTETION - Our humidity fogger can provide large amount of mist. Aerosolized amount≥400mL/H.No heat or chemicals used. Fast and safe shipping from US, delivery time: 4-6 working days.
• WATERPROOF - The ultrasonic foger is waterproof and the length of the power adapter cable is long enough. Ideal for indoor or outdoor fountains, water feature, and office use.
• NOTE - Ensure the water at high quality, use clean tap water, water quality deterioration may influence the lifetime. Please switch off the power before commissioning or maintenance. Mist Maker should be fully submerged in water.

User questions & answers

Question:	Will i get electricuted if i touch the water when powered on
Answer:	No you will not get electrocuted if you touch the water, but don't touch the mister's top while it's running. I found out the hard way, it bites!

• ♦ Multi-Appliable Scene -- AGPTEK Mist Maker can used in your pond, fountain, rockery, fish tank, vase, tank, etc. It will create a magical atmosphere. Especially perfect for Halloween and other holidays.
• ♦ Mini Size Large Capacity of Mist - Our fountain atomizer can produce large amount of mist although it. Aerosolized amount≥400mL/H.No heat or chemicals used.
• ♦ Ultrasonic Technology -- When putting this plant humidity fogger into your pond or water tank, it can add a great amount of mist t to filter the bad smell with electro and ultrasonic technology.
• ♦ Safe & Easy-Operated -- The voltage of AGPTEK mist makers is 24V, so it’s safe to use. Put it in the water then the mist appears.
• ♦ Long Cable -- The cable length of this ultrasonic foger is 210 cm(90cm attach to adapter, 120cm attach to mist maker), long enough to use in different scene. Ideal for indoor or outdoor fountains, water feature, and office use.

User questions & answers

Question:	can you use esscencial oils in the water you fog
Answer:	I used waterproof paint (ordered on Amazon).
Question:	Can it be use with live animals
Answer:	Hi most permanent markers are good as far as paint we use UV screen printing ink brand Nazdar you may find from screen printing supplier thanks

Product description

Specification:

Material: ABS plastic

Aerosolized amount:≥300mL/H

12 changing LED light.

Input: 110-240V, 50/60Hz(With a US AC/DC adapter)

Output: DC 24V, 700mA

Disc: 1.8inch.

Mist Maker Size: 1.8inch diameter, 1.8inch tall

Cable Length: 210 cm (82 inch) (90cm attach to adapter, 120cm attach to mist maker) , 3.5mm in diameter

How to Use:

1. DO NOT touch the atomizing slice while the Mist Maker is working.

2. Please SWITCH OFF the power before any movement or maintenance.

3. Keep the nozzle 2-3CM under the water level to get the best atomization effect.

4. Ensure the water is in high quality, use clean tap water.(not work for the distilled water)

5. The atomizing slice is consumable, and its service life is≥3000 hours. If the mist decreases, please clean the atomizing slice with a cotton swab(no need to use any detergent).Always keep it clean.

Package included :

1 x Mist maker(disc Not included)

1X removable splash guard

1 x AC-DC adapter (US plug)

• Fitnate mist maker can add a great amount of mist to your pond or water tank to filter the bad smell with electro and ultrasonic technology. You can put it in your pond, rockery, fish tank, vase, birdbath, etc. It creates a magical atmosphere. Especially perfect for Halloween and other holidays.
• Removable waterproof Buckler which can prevent the water spilling out so You can enjoy the magical environment without worrying water spilling everywhere.
• Our Mister Fogger can provide large amount of mist. Aerosolized amount≥300mL/H.No heat or chemicals used.
• Easy to operate. Put it in the water then the mist appears and the voltage is 24V so it’s safe to used.
• We believe our first responsibility is to the customers who patronize our store. We strive to offer superior customer service, technical support. You can be assured that you will receive a first class customer service and best shopping experience in using our store. We respond email in 1- 24 business hours.

User questions & answers

Question:	Lights just blink and no mist
Answer:	Yes, you can open the fan to clean the blades. Always unplug the fan before cleaning. Do not allow water to drip on or into the motor housing. Thank you.
Question:	Can this be used out of water
Answer:	I use the stationery and a Overbed Table https://www.amazon.com/dp/B01M0LEHAB enriches my new dorm. Very cool!
Question:	how long can you leave this on for
Answer:	I rescued one of these fans from a free pile and it was making a rattling sound upon startup. Removing the cage and applying couple drops of 3-in-1 motor oil to the motor shaft completely resolved the problem. Recommend doing this every year for any fan you have as regular maintenance.
Question:	Where can I buy the plastic "buckler
Answer:	That is a good question. This fan needs to be plugged in and does not run on batteries. If you have any other questions please do not hesitate to contact our consumer relations team by emailing us at [email protected]. Thank you.

Product features

FITNATE Electronic Mist Maker with Splach Guard

Removable waterproof Buckler which can prevent the water spilling out so You can enjoy the magical environment without worrying water spilling everywhere.

Mini Size to hold on hand

• MIni Size
• Easy to put in the mini container

6.5 Feet Connection Cable

Connection Cable:6.5 FeetFogger Size:1.8x1.8 InchSplash Guard:3 Inch

AC-DC adapter 24V US Plug

Electric-Powered

12 LED Flashing Light

• Input: 110-240V, 50/60Hz(With a US AC/DC adapter)
• Output: DC 24V, 700mA
• Disc: 1.8inch.
• Mist Maker Size: 1.8inch diameter, 1.8inch tall
• Aerosolized amount:≥300mL/H
• Cable Length: 210 cm (82 inch) (90cm attach to adapter, 120cm attach to mist maker) , 3.5mm in diameter
• Removable waterproof Buckler which can prevent the water spilling out so You can enjoy the magical environment without worrying water spilling everywhere.

How to Use:

1. DO NOT touch the atomizing slice while the Mist Maker is working.

2. Please SWITCH OFF the power before any movement or maintenance. 3.Keep the nozzle 2-3CM under the water level to get the best atomization effect.

4. Ensure the water is in high quality, use clean tap water.(not work for the distilled water)

5. The atomizing slice is consumable, and its service life is≥3000 hours. If the mist decreases, please clean the atomizing slice with a cotton swab(no need to use any detergent).Always keep it clean.

Garden

Rockery Landscape

Indoor Office

• WIDELY USE – FITNATE Aluminum mist maker can add a great amount of mist to your pond or water tank to filter the bad smell with ultrasonic technology. You can put it in your pond, rockery, fish tank, vase, tank, etc. It will create a magical atmosphere. Especially perfect for Halloween and other holidays.
• EASY TO OPERATE,-Upgrade vision,put in the water and the voltage is 24V, then lots of mist appears.
• ENVIRONMENTAL PROTETION - Our Mister Fogger can provide large amount of mist. Aerosolized amount≥400mL/H.No heat or chemicals used.
• SAFETY & EASY TO OPERATE - Put it in the water then the mist appears and the voltage is 24V so it’s safe to use.NOTE: Please DO NOT TOUCH THE WATER when it works.
• CUSTOMER SUPPORT - We strive to offer superior customer service and technical support. If you have any questions, please don’t hesitate to contact us, we respond email without 24 hours.

User questions & answers

Question:	I was under the impression this could used outdoors but the a/c adapter says for dry location use only. Am I missing something
Answer:	You can use to outdoor, but need to protect the A/C adapter. Becacuse this item need to plug. Thank you for the question. If you need more help,please kindly contact [email protected]. Thank you very much!
Question:	In one place you said 250 ml/h in other you say 400 ml/h. What if it runs out of water? What is the cost of replacement disks
Answer:	It is 250ml. We sorry for the trouble caused. We has revise it. Thank you very much for the question.
Question:	What is the droplet size
Answer:	It is 2.1cm, and this design just for make more fog. If you need more help,please kindly contact [email protected]. Thank you for the question.Have a nice day!
Question:	How long does it take to evaporate a specific amount of water
Answer:	I bought this to put a mist in my frogs terrarium and wasn’t able to use it because it vaporized a glass of water in a few minutes. This would be perfect for a tub at Halloween or a pond but not for a small cup.

Product features

Upgraded-Lots Foggy Effect

We upgrade it and mist maker can add a great amount of mist to your pond or water tank to filter the bad smell with ultrasonic technology.It also add the mist chip to enlarge its lifetime.

Don't touch

Don't touch the atomizing slice while the mist maker is working. The ultrasonic frequency exceeds the human body’s frequency range, so your finger may feel numbs if you touch, but please know that its Not Electric Leakage. our product’s voltage is 24V so it’s safe to used in the water.

Item Specifications

1. Mist Maker Size: 1.5" diameter, 0.98" tall
2. Aerosolized amount:≥400mL/H
3. Disc:0.49".
4. Input: 110-250V, 50/60Hz,Output: DC 24V, 700mA
5. Cable Length: 7.2 inch totally

Product description

Description:

Mist Maker Size: 3.5 cm diameter, 4cm tall.

Disc: 1.6cm.

Output Voltage: 24V DC.

With a US AC/DC adapter .

Input: 110-250V, 50/60Hz

Output: DC 24V, 700mA

Cable Length: 210 cm (82 inch) (90cm attach to adapter, 120cm attach to mist maker) , 3.5mm in diameter.

Package included :

1 x Mist maker

1 x AC-DC adapter (US plug)

Points for attention:

1. Do not turn over the Mist Maker When the switch is turned on, keep upright, or it may damage the atomizer.

2.Please ensure that the daily running time is less than 10 hours, otherwise the life of atomizing slice will be shorted.

3. Don't touch the atomizing slice while the Mist Maker is working.

4. Ensure the water at high quality, use clean tap water.(water quality deterioration may influence the lifetime)

5. Please switch off the power before Movement or maintenance.

6. The atomizing slice is consumable,and its service life is¡Ý3000 hours.If marked reduction of Mist present, please clean atomizing slice with a cotton swab(don't need to use any detergent).Keep it clean.

Note:

The product of the nozzles upper part, the water injection mouth more than 2-3 cm best, not less than nozzles, also cannot too higher than nozzles

• Add a stunning mist effect to your pond or water tank to filter the bad smell with electro and ultrasonic technology;
• Ideal for indoor or outdoor fountains, water feature, and office use.
• Easy to operate, put in the water and the voltage is 24V, then the mist appears.
• Atomization Amout: ¡Ý400mL/H
• Mist Maker Size: 4.6 cm diameter, 4.2cm tall

User questions & answers

Question:	Do i need to buy a flot for it
Answer:	You would need an external enclusure or docking station that has its own power supply. A USB adapter only does not have enough power to control the drive.
Question:	Which diameter is accurate for the head that doesn't have LEDs? 3.5cm or 4.6cm
Answer:	back up your data the motor is starting to fail
Question:	What depth of water would need be to cover this? I plan to put it in the bottom of a 10 gallon aquarium that I will be using for a terrarium
Answer:	its up to you. i hoarded all my old computer parts over the years so i never had a shortage for projects.
Question:	How big is the ultrasonic disc on this? Can it be replaced? Thanks
Answer:	If you’re using this as a boot drive for windows 7 then you’re probably not going to be able to have a partition larger than 2 TB. To have a boot partition larger than 2 TB it must use a GPT partition table as opposed to a master boot record. Search the Internet for “windows 7 boot drive larger than 2tb”

• [HEAT UP QUICKLY] 400-watt high-efficiency heater block warms up in 4-5 min and leaves little residues, which helps to extend the service life of machine.
• [LARGE TANK CAPACITY & 0.3OZ/MIN FLUID CONSUMPTION] 300ml (10.1 oz.) tank capacity lasts between 1 and 3 hours depending on use; 0.3oz/min (7.5ml/min) fluid consumption quickly transforms your environment.
• [PORTABLE] measured at 9.1” x 4.3” x 4.5” and weighing 3.5 lb., this fog machine highly portable for smaller venues of area use.
• [LONG WIRE & OUTPUT DISTANCE] 9.8ft.wire control & 6.6~9.8ft.output distance let you position your fogger where you need it, ready to create the ideal effect you want.
• [100% SAFETY & SUPERIOR QUALITY] CE and RoHS approval, ABS environmental materials, safer metal wire; made for use with quality water-based fog fluid.

Product features

Huge Output & Wide Coverage

• After less than 5 minutes of preheating, our smoke machine begins to cover 7–10 feet with a mass of fog, improving your parties, performances, and more!

User-Friendly Design

• The clear gauge lets you easily track the device's fluid level while the built-in fuse prolongs its service life by preventing power surges and overheating.

Precise Temperature Control

• Our advanced smoke machine precisely controls its temperature using a built-in thermostat to ensure full atomization of the fog. Its fan and vents efficiently disperse the heat created to keep it running smoothly for years.

Add In Fog Fluid

Pour your professional fog fluid into the tank until it fills 50–80% of the tank. Never add any flammable liquids.

• Fluid Consumption: 1.5 tsp/min. (7.5 mL/min)
• Output Distance: 6.5–10 ft. (2–3 m)
• Tank Capacity: 10 fl. oz. (300 mL)

Power Switch

Flipping the power switch gets the machine running and starts the preheating process that will allow it to efficiently atomize your fog juice into a massive cloud bank.

Remote Control

The light on the wire remote turns red when preheating is over and the machine is ready to go. Press the button and your fog will begin to flow out from the front nozzle.

• WIDELY USE – FITNATE Three-head mist maker can add a great amount of mist (Ups to 1500ML/H) to your pond or water tank to filter the bad smell with ultrasonic technology. You can put it in your pond, rockery, fish tank, vase, tank, etc. The magical mist maker comes with 12LED changing colors Lights create a magical atmosphere for your pond or aquarium in any Holidays.
• EASY TO OPERATE-Upgrade visions, put in the water (2 ~ 3cm lower than the horizontal plane) and the voltage is 24V, then lots of mist appears. staff float also included.
• ENVIRONMENTAL PROTETION –This Fogger can provide large amount of mist. Aerosolized amount≥1500mL/H. No any chemicals used.Note:Do not touch the Atomizer head when used,
• SAFETY & EASY TO OPERATE - Put it in the water then the mist appears and the voltage is 24V so it’s safe to use. When the item is short of water during operation, it will be powered off in time, safe and reliable.
• CUSTOMER SUPPORT - We strive to offer superior customer service and technical support. If you have any questions, please don’t hesitate to contact us, we respond email without 24 hours. Three additional atomizing discs and changing tools are equipped to extend the service life of the Ultrasonic Mist Maker.

Product features

Points for attention:

• 1. Don't touch the atomizing slice while the Mist Maker is working.
• 2.Please ensure that the daily running time is less than 10 hours, otherwise the life of atomizing slice will be shorted.
• 3. Please use clean tap water.(water quality deterioration may influence the lifetime) Distilled water and purified water do not work
• 4. Please switch off the power before Movement or maintenance.
• 5. The atomizing slice is consumable, If it dot not fogged anymore, please replace the atomizing disc with the tool provided.(The fogger head is relatively tight. You can use the Small screw driver to pass through the small hole of the fogger head to open it.)

Features:

Material: ABS plastic

With LED Changing color lights

Input: 110-220V, 50/60Hz(With US AC/DC adapter including)；Output: DC 24V, 700mA

Maximum evaporation: 1500ml/H

Environment temperature:+1℃~45℃

Use water depth:6-9cm (2 23/64’’-3 35/64’’)

Size:φ70*45mm (2 3/4‘’*1 49/64‘’)

Product description

Warning Tips:

1. Keep water level higher 0.8~1.2inch depth than the mist maker.
2. It will heat a bit of when using, so don’t use it in fish tank.
3. Don't touch the atomizing slice while the mist maker is working.
4. Do not turn over the mist maker when it is in working statue.
5. Please turn off the power before movement or maintenance.
6. Please don’t touch water when it works.The frequency exceeds the human body’s frequency range, so your finger may feel numbs if you touch, but please know that its. Not Electric Leakage. Our product’s voltage is 24V so it’s to use in the water.

Tips about mist maker service life:

1. Do not drop any essential oils in when using.
2. Atomizing slice is consumable, and its service life is about 3000 hours.
3. Please ensure that daily working time should be less than 10 hours, otherwise the lifespan of atomizing slice will be shorted.
4. Ensure the water at high quality, use clean water.(water quality may influence the lifetime)
5. For the good of mist make performance and service, please change clean water in every week, and use soft cloth to clean the mist maker sensor and head, and do not scratch the mist maker sensor or head with sharp tools.

Specifications:

• Material: Aluminum
• Aerosolized amount:≥400mL/H
• Input: 110-240V, 50/60Hz
• Output: DC 24V, 700mA

Package included:

• 1x mist maker
• 2x mist maker disc
• 1x key
• 1x stand
• 1x instruction
• 1x US plug adapter

• WIDELY USE - This mist maker fogger can create a thick steam effect. You can put it in Halloween cauldron, pond, rockery, vase, tank, water fountain, etc
• WATERPROOF - This mini fog maker is waterproof and its power cable is long enough. It's ultra quiet and auto shuts off when the water is gone
• THICK MIST EFFECT - Aerosolized amount ≥400mL/H. It produces a nice amount of misty fog to create a magical atmosphere on Halloween and other holidays
• NO WATER ALL OVER - A detachable stand is supplied for no water going all over
• EASY TO USE - Voltage is 24V so it can be used in the water. Plugged it in, lights come right on and the mist starts right up.

Product description

Mist Maker, Indoor Fountain Mister Foggers, Small Pond Fog Machine Atomizer Air Humidifier Perfect f

• PULACO mist maker can create dense mist for your pond or water tank in seconds, it is 100% water mist, smelless and colorless, use electro and ultrasonic technology. You can put it in your pond, rockery, fish tank, vase, birdbath, etc. It creates a magical atmosphere.
• 【Easy to use】: Put it in the water then the mist come out and it is 24 V voltage safe design. Install the mist maker under water depth 2-2.8 inches (water level: 0.6inch between mist maker sensor and water surface)
• 【Mist maker cable length】: 7.0 ft, ( 3.0 ft attach to adapter, 4.0 ft attach to mist maker)
• 【Note】 Ensure the water at high quality, use clean tap water, water quality deterioration may influence the lifetime. Please switch off the power before Movement or maintenance. Mist Maker should be fully submerged in water. Do not put your hands cover above the centre mist while it working, it may causing discomfort. Mist maker can not working continously over 8 hours.

User questions & answers

Question:	I bought this in October and it quit working today. What happened
Answer:	Mine quit working about 10 days of use (we use it for our Gecko). Perhaps distilled water is the way to go?
Question:	does this unit have an auto off when the water gets low
Answer:	Yes. It does shut off when water is low
Question:	Plugged it in put in water , not working and no leds . should i use distilled water
Answer:	Distilled water is not necessary. If your Mist Maker is not working when plugged in and immersed in water, it might just be defective. We tried different receptacles for the water to make sure that the device was covered.
Question:	How can I make this stop splashing so much? The rubber “adjuster” doesn’t do much
Answer:	That I'm not sure. I'm using mine in a bowl that has an additional piece that sits over the mister, that way it bubbles up under this additional piece. So, it just drips back into the bowl. Look it up. There called misting bowls. I bought this for that bowl. My mister died. This replacement works great.

Product features

Installation:

1. Take out the mist maker and AC/DC adaptor, connect the DC plug.

2. Install the mist maker under water depth 2-2.8 inches (Best working water level: 0.6inch between mist maker sensor and water surface) and plug-in the adpator.

3. There is a cable cap on the power cord, adjustable, thats for prevent mist gathered into water droplets, flows out and affect other devices.

Application

PULACO Mist Maker, using ultrasonic electronic technology to make the water molecules into fog molecules.smelless and colorless. Perfects for being used in your pond, botanical garden, rockery, fishtank, vase, pool.,etc. It will create a magical atmosphere. Easy to operate, put it into the water, then the mist appears. Ideal for indoor or outdoor fountains, water feature, and office use.