9 best rf spectrum analyzers

• Spectrum Analyzer with two inputs, high quality MF/HF/VHF input for 0.1MHZ-350MHz, lesser quality UHF input for 240MHz-960MHz
• Built-in calibration signal generator that is used for automatic self test and low input calibration.
• Switchable resolution bandpass filters for both ranges between 2.6kHz and 640kHz.Color display showing 290 scan points covering up to the full low or high frequency range.
• When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 0.1MHZ-350MHz, UHF square wave output between 240MHz-960MHz.
• Connected to a PC via USB it becomes a PC controlled Spectrum Analyzer.Bulit-in rechargeable battery allowing a minimum of at least 2 hours portable use

User questions & answers

Question:	Does it come with the touch screen pen
Answer:	Yes, a small plastic pen.
Question:	Is this suitable for testing tv vhf and uhf signal strength
Answer:	Not an expert on TV VHF and UHF, but I believe the TinySA range covers the UHF and VHF spectrum. With some calibration and manual setting (research on YouTube) it will provide accuracy that meets most needs. It is not a $2500 SA, so expect a certain amount of "ok, but its only $50 bucks". Also, ATTENUATE if signal strength/input is expected to be high. Again, research videos with professional testing from engineers. There's plenty of help online.
Question:	can this be used to display and analyze noise on an AC power line
Answer:	You might be better off with an oscilloscope. The TinySA does not have high input impedance and a direct measurement on the power line would likely damage it (and be very unsafe).
Question:	is there a linux-based version of the app
Answer:	Yes,it support

Product features

The tinySA is a small spectrum analyzer, primarily intended for 0.1MHz to 350MHz

Specification: * Display resolution 320*240 pixels * Screen diagonal 2.8" * 16 bits per RGB pixels * Resistive touch control * Jog switch control * USB serial port control * Optional TTL USART port (SW not yet implemented) on the internal PCB * Linear power supply to avoid switching noise.

USB Charging

Charging time max 1 hour on 500mA minimum USB port or USB charger.Operation on fully charged battery for at least 2 hours

PC Control

The USB interface implements the Serial over USB (CDC) protocol and there is a large set of commands that can be invoked over the serial interface. These command can be used to perform measurements or update internal settings. The driver for Windows will install automatically after connecting to a Windows PC. The driver for Linux is built into the kernel

• [Impressive frequency range] – Scan and diagnose any frequency starting in low frequency 50KHz up to high frequency 6.1GHz, with no gaps or limitations. Offering this wide operating range, it can detect all WiFi, cell stations and phones, IoT, HAM bands, Digital radio and TV, ISM bands, Drone links and pretty much all wireless technologies used in todays demanding communications world.
• [Robust design and instant power up] – A fully armored metallic enclosure provides robust mechanical strength and the high quality baked varnished paint provides a unique glossy finish. The device is designed and manufactured to last many years of demanding usage in the field, with internal rechargeable Lithium battery for hours of continuous usage.
• [Advanced features] – Included advanced high-resolution Spectrum Analyzer mode, WiFi Analyzer mode, Tracking SNA. Internal firmware is continuously updated with additional features and functions to improve the device capabilities.
• [Free Computer software] - When connected to a Windows, Linux or Mac computer the analyzer can display advanced high resolution graphics, including Power Meter and Spectrum Analyzer real time charts, historical charts, save data to CSV files and export to other tools such as WW6 or MatLab, define markers and limit lines and much more. Free open source API and libraries are available to customize your own applications and services.
• [Tracking mode enabled] – When combined with RF Explorer Signal Generator the analyzer can perform full tracking SNA to define Gain, Attenuation and SWR for 1 and 2 port RF devices such as filters, amplifiers and antennas.

User questions & answers

Question:	Does this have a usb-c port
Answer:	Hello, unfortunitly this unit doesn't have a USB-C port. It comes with a Mini USB Cable. I hope that this helps.

Product description

LATNEX  SPA-6G is a handheld digital spectrum analyzer and RF explorer that works in all popular frequency bands. 

It is based on a highly integrated frequency synthesizer and double balanced mixer which offers high performance, compact size, low consumption and low cost. It has been designed to be used equally well outdoor and indoor, and can be connected to a PC for extra functionality using standard mini-USB 2.0 connector. 

It comes with two SMA connectors and three antennas: Nagoya NA773 wideband telescopic antenna for all Sub-GHz frequencies, a rubber duck 5.8 GHz and a whip helical for 2.4GHz band. Additional, specific band antennas may be needed to cover efficiently some of the frequencies supported. The unit offers coverage for most used communication frequency range such as WiFi, Bluetooth, Wireless Audio and Video, LTE, GSM, GPRS, Satellite, CATV, DTV, etc. 

The SPA-6G Combo package includes the SPA-6G spectrum Analyzer and an aluminum protective and carrying case as well as additional accessories. This Aluminium carrying case allows you to protect your  device and keep all the parts and components organized.

* TWO YEARS WARRANTY with full support includes free Firmware upgrades.

• IMPRESSIVE WIDE FREQUENCY BAND from 15MHz-2.7GHz and 4.85GHz-6.1GHz.
• WIFI ANALYZER MODE Allow you to identify Wifi issues and find the optimized channel or the best place for your routers or access-points to be places.
• MORE ADVANCED FUNCTIONALITY AVAILABLE for the SPA-6G RF explorer by connecting to a Windows or MAC PC using the free downloadable professional software with Waterfall 3D and 2D elements.
• BONUS DELUXE CARRY CASE included in this value SPA-6G combo kit. This Aluminum hard carrying case provide you with an easy and convenient way to protect and transport your spectrum analyzer and keep all the parts and components organized.
• 100% MONEY BACK GUARANTEE ensures this will quickly become your favorite no-risk purchase.

User questions & answers

Question:	what type Lithium ion battery
Answer:	Hello, Li-ion polymer rechargeable battery. Rated Voltage: 3.7V Normal Capacity: 1000mAh
Question:	Does it come with factory calibration certificate
Answer:	Hello thank you for reaching out to us. Yes it does come with a calibration certificate.
Question:	Is this a real time spectrum analyzer
Answer:	Yes. It does much of what an expensive lab instrument does for a fraction of the cost. It has fixed resolution of 112 data points at 200 ms sweep time.
Question:	work on smartmeters
Answer:	Hello, The LATNEX spectrum analyzer will accurately measure the RF signal emitted from the smart meter. Please do not hesitate to contact us in case you need assistance with measuring the smart meter signal.

• 2.4 GHz and 5 GHz Spectrum Analyzer views all interference including ZigBee, Bluetooth, Baby Monitors, etc
• Android, iOS, Mac, PC Supported
• Scan and Troubleshoot Wi-Fi
• SSID’s and RSSI
• 802.11 and ZigBee Channel Guides

User questions & answers

Question:	Does it capture Z band
Answer:	No, but WiPry 790 covers Z-Wave: 868.42 MHz for Europe and 908.43MHz for US.
Question:	What is the difference between wipry 5x and wipry 2500x
Answer:	Good question: one key difference is that the WiPry 5x is no longer offered (although there are a few legacy units still floating around in select markets). It has now been replaced by the WiPry 2500x. Some differences: WiPry 2500x has AAA batteries (minimizes the impact to phone battery) and as a result is slightly larger.
Question:	Will this work on ax/ac protocols? i have a wifi interference problem that's annoying af, can't seem to find the problem
Answer:	Hello, yes this should work for what you are looking to use it for. I hope that this helps.
Question:	What is the DC voltage range for a battery charger? There is no information in their app or manual re the charger, and it doesn't come with one
Answer:	The connector is a USB Micro B and should provide 5v, 100mA. The circuit will accept any voltage from 2.6 to 9v.

Product features

Portable Field Tool

WiPry 2500x can help make your Wi-Fi awesome, and it can be done on-the-go. Just download the free app (WiPry) from either the App Store or Google Play to see how it works!

See The Invisible RF Landscape!

WiPry 2500x visualizes SSID's as well as all RF activity on both 2.4 & 5 GHz. This includes: baby monitors, cordless phones, garage door openers, and microwave ovens (to name a few)

Improves Wi-Fi Speed & Reliability

WiPry 2500x will help improve the grade of your wireless environment by helping you: avoid interference, educate customers, identify interference sources, optimize the channel, and undo / relocate hardware.

Works with iOS, Android, PC, Mac

Oscium’s WiPry 2500x is compatible with iOS, Android, PC and Mac. This cross platform solution is perfectly portable as are all Oscium’s tools. And now, it’s possible to use whichever host device you prefer. Oscium's software applications are all free. There's no licensing fee and there's no subscription so it's easy to use your WiPry 2500x.

The Perfect Blend of Performance & Portability

System Requirements (Software):

• iOS version 7.0+
• Android version 6.0+
• Windows 7+
• Mac OS 10.10+ (Yosemite)

System Requirements (Hardware):

• iOS Lightning Devices (iPad, iPhone, iPod)
• Android Devices with USB OTG
• Windows/Mac USB 2.0

Advanced Reporting

Oscium's WiPry 2500x auto-analyzes your wireless environment and provides a report highlighting everything you need to know:

• grade channeling for your Wi-Fi network (using A through F, just like in school!)
• signal to noise ratio (perfect for knowing whether VoIP or video streaming is possible)
• play / record (helpful in capturing intermittent issues)
• birth certificates (tracks Wi-Fi health)
• view environment over time using waterfall mode

Product description

RF Explorer 6G COMBO+ is the most powerful Spectrum Analyzer model, covering the full 6GHz range starting at 50KHz up to 6.1GHz with no gaps or limitations.

When compared to the standard 6G Combo model, the new SLIM design offers an outstanding robust enclosure with strong metallic body and shiny varnished paint, a more convenient USB connector on the side and larger internal battery capacity.

Features

• Internal LNA amplifier and selectable attenuator for additional power range handling.
• Low frequency support from 50KHz covering LF, MF, HF, VHF and UHF
• High frequency support covering all range up to 6.1GHz with no gaps.
• New HELP and SET buttons to improve user interface and PRESET configuration selection with 2-clicks
• Ideal choice for all usable HAM bands.
• Pocket size and light weight
• Solid metal case with high quality varnished paint
• Spectrum Analyzer mode with Peak Max and Hold, Normal, Overwrite and Averaging modes
• High capacity internal Lithium battery for 10hs+ of continuous run, rechargeable by USB
• Multi-platform Windows/Linux/MacOS Open Source software and API libraries

• ✔️ Frequency band: 50KHz - 960MHz and 240MHz - 6.1GHz;Amplitude resolution: 0.5dBm
• ✔️ Wifi Analyzer mode for the 2.4GHz and 5GHz bands
• ✔️ Free Mac and Windows software for analysing RF and WiFi networks using Waterfall 3D and 2D
• ✔️ Aluminium carrying case allows to to protect your RF Explorer device and keep all the parts and components organized
• ✔️ Full support and 2 year warranty

User questions & answers

Question:	anybody use the software on a mac
Answer:	It connects directly to your cars sound system, you can purchase a speaker wiring harness for you specific make and model vehicle, as well as wire stripper to help you strip and connect the wires. So to answer your question no it does not need an amplifier, although you can purchase and install one if you want too.
Question:	The product description says: "frequency band: 15mhz-2.7ghz and 4.85ghz-6.1ghz". does that mean it cannot measure between 2.7 ghz and 4.85 ghz
Answer:	Try using a different cable, my father had a similar issue with his old Ipod. A new cable fixed the issue immediately.
Question:	Will this grab dsss pulse spread spectrum? and for more convenient utility is there an app to download to utilize an ipad for field work
Answer:	It comes with a small mic, other than that no remote controller unfortunately.
Question:	Will this device detect nuclear radiation
Answer:	Can run speakers 4-8 ohm

• Multiple high sensitivity sensors installed for detecting Power line, Smart meter, Cell phone, Microwave etc.
• Identify/recognize the common possible sources, such as Power line, Cell Tower, Microwave, Static etc.
• Safety suggestion lets you understand current situation instantly.
• Detects 5G network signal and RF up to 10Ghz
• Built-in RF Spectrum analyzer and GQ RF Browser for real time RF monitoring.

User questions & answers

Question:	All i want to know if this detector gq emp-390 will detect 5ghz wifi signal and 5g cell phone
Answer:	Yes it will detect 5GHz signal but not in all modes of operation. If it is the predominant source then the general Radio Frequency RF mode reading will reflect it. If it is a source mixed with others than all sources will be reported together as one value (sum/average over time...unknown. most likely average). It will not detect it in spectrum analyzer, by frequency, and show it's individual power level. Spectrum analyzer will detect 2.4GHz wifi. 5GHz is out of range of spectrum analyzer as is everything greater than 2.5GHz. It might detect presence of 5GHz data packet bytes in digital mode but I don't know for sure, have not tested this.
Question:	Can it tell you how much emf your cell phone emits
Answer:	yes it does, in 3 scales. some readings read a voltage per meter and another is electro-magnetic reading, I searched through alot and after receiving this I found it to be the best affordable technology in its class, and it even automatically identifies the difference between cell phone and power line EMF in digital readable format.
Question:	Will this device analyze a 5 gig wifi signal like it does a 2.4 or
Answer:	Yes, it does analyze 5 Ghz frequencies. If you are asking whether it will analyze 5G as in 5th generation Millimeter Waves, the answer is NO.. 5th Generation 5G will use frequencies between 30Ghz and 300Ghz... You can get one that costs about $40,000... As in, they are not available to the public .
Question:	Is the 5g wifi signal the same as the new 5g cell phone signal? will it measure the new 5g phones? it is confusing: it says: "rf up to 10 ghz
Answer:	The 5G wifi is referring to 5Ghz Wifi, and it is covered by this meter RF band. The 5G cell phone network is referring to 5th Generation cell phone network, it is nothing to do with 5GHz, basically its base band is much higher than 5Ghz

Product features

New display maximizes the amount of information

• All-in-One display lets you see reading from all sensors at once.
• Advanced features and multi-sensors to ensure best detection from EMF, EF and RF.
• Compact design for easy testing and measurement.
• Safety suggestion lets you understand current situation instantly.
• Radiation source recognition provide fastest way to find out the radiation source.

Classic display option is quick to adapt application

• With traditional analog style display, the data becomes even easier and faster to understand.
• Left and right vertical bars are also indications of the EF and EMF radiation level in glance.
• Safety suggestion in large font for easier reading.
• Real Time clock displays current time for time sensitive testing.
• Front LED visualizes alarm when triggered.

Real-Time EMF EF Graph

• Presents exact changes of EMF and EF radiation level been detected in past 45 seconds.
• The right side of graph shows a reading for both EMF and EF.

RF Spectrum Analyzer

• Advanced users are able to use built-in RF Spectrum Analyzer to discover the RF signal power in a specific frequency.
• This graph shows two RF signal that has been detected at same time: Microwave oven and WiFi signal.

RF Browser

• GQ RF Browser is a unique feature of GQ EMF detector. The real-time graph is based on high sensitivity sensors.
• This graph shows a close by cell phone that just received a text message.

Real-Time Power Distribution Histogram

• RF power distribution is another important factor to let us understand how the RF radiation power distributed during the period.
• This graph shows the highest RF power is 6.47% of total at 0.049 milliWatts per square meter during the testing period.

Product description

User interface:

Display resolution 320*240 pixels

Screen diagonal 2.8"

16 bits per RGB pixels

Resistive touching control

Jog switch control

USB serial port control

Optional TTL USART port (SW not yet implemented) on the internal PCB

Linear power supply to refrain switching noise

 

The input/output specification of the tinySA is split over the 4 modes.

Low input mode spec:

Input frequency range from 100KHz to 350MHz.

Input impedance 50 ohm when input attenuation set to 10dB or more.

Selectable manual and automatic input attenuation between 0dB and 31dB in 1dB steps.

Absolute maximum input level without attenuation of +10dBm.

Absolute maximum input power with 30dB attenuation of +20dBm for short period.

Input intercept point of third order modulation products (IIP3) with 0dB attenuation of +15dBm.

1dB compression point at +2dBm with 0dB attenuation.

Power detector resolution of 0.5dB and linearity ver-sus frequency of +/-1dB.

Absolute power level accuracy after power level calibration of +/-1dB.

Lowest discernible signal using a resolution bandwidth of 30KHz of -102dBm.

Frequency accuracy equal to the selected resolution bandwidth.

Phase noise of -90dB/Hz at 100KHz offset and -115dB/Hz at 1MHz offset.

Spur free dynamic range when using a 30KHz resolution bandwidth of 70dB.

Manually selectable resolution filters of 3, 10, 30, 100, 300, 600KHz. Automatic selection of one of the 57 resolution filters.

On screen resolution of 51, 101, 145 or 290 measurement points.

Scanning speed of over 1000 points/second using largest resolution filters.

Automatic optimization of actual scanning points to ensure coverage of the whole scan range regardless of the chosen resolution bandwidth.

• Dual input and output: 0.1MHz-350MHz low-quality MF/HF/VHF input, 240MHz-960MHz high-quality lower UHF input. Band-pass filter with switchable resolution, suitable for the range between 2.6KHz and 640KHz
• 2.8 inch TFT color display: it can display 290 scanning points, covering the entire low or high frequency range. The input step attenuator for MF/HF/VHF input is 0dB to 31dB
• With signal generator function: when not used as a spectrum analyzer, it can be used as a signal generator, MF / HF / VHF sine wave output between 0.1MHz-350MHz, UHF square wave output between 240MHz-960MHz
• Connect to PC via USB, it becomes PC controlled spectrum analyzer.
• Can be carried for at least 2 hours

User questions & answers

Question:	can , i...use this to align a parabolic 2.4 ghz.antenna to a wifi cell tower
Answer:	Hello, The ISM Combo Spectrum Analyzer will measure frequencies between 240MHz - 960 MHz and also 2.35-2.55GHz. This unit will not align a parabolic 2.4 GHz antenna to a wifi cell tower.
Question:	Good for detecting 5g
Answer:	The unit I ordered is limited to the 2.4Ghz ISM band and sub-Ghz cellular bands. Don't know if the company makes a 5G version. Also the device works very well for my use and is unusually accurate for a handheld device.
Question:	Does it demodulate the signal so you can listen to the signal either from the computer or standalone unit
Answer:	No it does not. It will simply show all the frequencies that are being used for a given frequency range and their signal strength. It is not an actual receiver.
Question:	Wierd questuon i know but i have a semi hobby semi pro lifestyle they would say. it's weird so i'll just say it. does it detect ghosts
Answer:	Only if they are using an RF radio to communicate. And Yes it is a weird question.

• 【Input Frequency Range】Spectrum Analyzer with two inputs, high quality MF/HF/VHF input for 0.1MHZ-350MHz, lesser quality UHF input for 240MHz-960MHz.
• 【2-in-1】Built-in calibration signal generator that is used for automatic self test and low input calibration.When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 0.1MHZ-350MHz, UHF square wave output between 240MHz-960MHz.
• 【2.8inch Touching Display Screen】Switchable resolution bandpass filters for both ranges between 2.6kHz and 640kHz.Color display showing 290 scan points covering up to the full low or high frequency range.
• 【PC Controlled 】Connected to a PC via USB it becomes a PC controlled Spectrum Analyzer.Bulit-in rechargeable battery allowing a minimum of at least 2 hours portable use.
• 【Package List】1x Tiny Spectrum Analyzer;2 x 20cm RF Cable;1 x USB Cable;1 x Touching Screen Paddle;1 x SMA Female to Female Connector;1x Touchscreen Pen;1 x SMA Telescopic Antenna.

User questions & answers

Question:	Will this product work with older versions of windows, like xp or windows
Answer:	Dear friend,good day. Thank you so much for your question. But we are so sorry to tell you that this Spectrum Analyzer Handheld is only supported windows systems above windows 7 (including windows 7),but not XP. Apologize for any inconvenience. Thank you so much for your understand. Best wish Any question, feel free to contact us and we will reach you at the soonest.
Question:	Can this unit be used on a tv antenna system to measure signal levels
Answer:	Dear friend,good day. Thank you so much for your question. But we are so sorry to tell you that this Spectrum Analyzer Handheld can not be used on a tv antenna system to measure signal levels. Apologize for any inconvenience. Thank you so much for your understand. Best wish Any question, feel free to contact us and we will reach you at the soonest.
Question:	Are there only two possible settings for resolution bandwidth or can i set resolution bandwidth to any value between 2.4 khz and 640 khz
Answer:	Dear friend,good day. Thank you so much for your question. The TinySA Spectrum Analyzer can be settings any resolution bandwidth between 100kHz to 960MHz. Of course,you can set resolution bandwidth to any value between 2.4 khz and 640 khz. I sincerely hope that it can help you well. Any question, feel free to contact us and we will alway there for you. Best wish

Product features

Handheld Tiny Spectrum Analyzer TinySA 2.8inch Touch Screen,Portable Frequency Analyzer 0.1MHz~ 960MHz MF/HF/VHF UHF Input, Signal Generator

Specification: Display resolution 320*240 pixels Screen diagonal 2.8" 16 bits per RGB pixels Resistive touch control Jog switch control USB serial port control Optional TTL USART port (SW not yet implemented) on the internal PCB Linear power supply to avoid switching noise.

4 Modes for Input/Output

Low input mode : 100kHz to 350MHz High input mode : 240MHz to 960MHz Low output mode : 100kHz to 350MHz(Sinus) High output mode : 240MHz to 960MHz(Square wave)

Optional square wave output with fundamental at -25dBm connected to high input/output. Frequency can be set to 1MHz, 2MHz, 4MHz, 10MHz, 15MHz or 30MHz.

Built-in Calibration Signal Generator

Built-in calibration signal generator that is used for automatic self test and low input calibration.When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 0.1MHZ-350MHz,UHF square wave output between 240MHz-960MHz.

PC Control

The USB interface implements the Serial over USB (CDC) protocol and there is a large set of commands that can be invoked over the serial interface. These command can be used to perform measurements or update internal settings. The driver for Windows will install automatically after connecting to a Windows PC. The driver for Linux is built into the kernel.

2.8inch Touching Display Screen

Switchable resolution bandpass filters for both ranges between 2.6kHz and 640kHz.Color display showing 290 scan points covering up to the full low or high frequency range.

Built-in 650mAh Battery

Charging time max 1 hour on 500mA minimum USB port or USB charger.Operation on fully charged battery for at least 2 hours.

Product description

Triplett's Wi-Fi Hound 2.4 GHz & 5 GHz Portable RF Professional Spectrum Analyzer is designed to help you troubleshoot and isolate problems that impact the quality of your wireless networks. No engineering degree needed! With its user-friendly display, you will properly analyze the wireless environment and successfully troubleshoot. Designed for live environments and thanks to its Zigbee capabilities (802.11.15.4) this tool is a must for home and business automation systems. The Wi-Fi Hound helps you isolate problems that impact the quality of your wireless networks. Especially interference from non-Access Points or competing wireless networks. As a Spectrum Analyzer, it displays everything in the 2.4 GHz and 5 GHz radio spectrum; including signals broadcasted from Wireless Networks, Bluetooth, Zigbee devices, external radio signals, machinery signals and more! This perfectly portable device is the ideal solution for field techs and wireless professionals. You can use the Wi-Fi Hound during your initial Site Survey at a new location to quickly optimize channel and power settings on your Access Points and see what other things may cause problems. Founded in 1904, U.S.-based Triplett Test Equipment continues to be on the leading edge of specialized testers. Whether supplying vital test equipment to the U.S. Signal Corps during WWII, or providing the railroad industry with essential testers to ensure the safety of their crews and the public, Triplett prides itself on developing innovative, reliable, and durable test equipment that also won't break the bank. Triplett's catalog contains a wide array of test equipment parts and accessories such as multimeters, voltmeters, cable testers, security cameras and security camera accessories, wire cable mapping kits, video monitors, and other specialty testers. They serve industries such as HVAC, security, electronics and electrical, telecom, and more.

• Troubleshoot and analyze all your Wi-Fi issues - displays everything in the 2.4 Ghz and 5 Ghz spectrum, including Zigbee, so you can isolate problems that impact your network
• Use the WiFi Hound during your initial site survey at a new location to quickly optimize channel and power settings on your Access Points
• Designed for live environments with an adjustable refresh rate
• Ideal for smart homes and businesses
• Data visualization and reporting

Product features

Analyze Your Wi-Fi

With its user-friendly display, troubleshoot and analyze all your Wi-Fi issues. Displays everything in the 2.4 Ghz and 5 Ghz spectrum, including Zigbee, so you can isolate problems that impact your network.

Designed For Live Environments

Detect and isolate problems that impact the quality of your wireless environments, exposing crowded networks and noisy interferences, including Bluetooth, microwaves, and more. Perfect for Initial Site Surveys to optimize channel & power settings.

Data Visualization and Reporting

Display number of SSIDs, BSSIDs, RSSIs, APs, Graded Channels in Use, and non-overlapping Open Channels. Additionally, create Full-Color Custom Reports that are branded to your company, showing all of the captured data.

Ideal for Home and Business Automation

Thanks to its Zigbee capabilities (802.11.15.4) this tool is a must for home and business automation systems. The Wi-Fi Hound helps you isolate problems that impact the quality of your wireless networks.

Spectrum Analyzer for 2.4 GHz & 5 GHz, including Zigbee

Advanced filters include: Select specific wireless channel, Adjustable RSSI View Range, Focus in on a single AP by Mac Address, Show Broadcast Type (n, g, ac, etc.), Show Channel Number.

Snapshot Feature instantly shows you SSIDs detected, APs detected, Channels, and Non-overlapping Channels Open.

Table View includes Custom sort and hold functions, Type of AP (e.g., Ruckus, Ubiquiti, Cisco, etc), Screen capture to add data to your reports, and Document Your Findings.

Create Custom Reports that are full-color and custom-branded to your company. Include captured data, clients & location details, and send completed reports to your clients instantly.