13 best commercial door power supplies

Product description

Features:



1. Ac 9 v ~ 260V, 50 hz ~ 260 hz, DC output standard:12 VDC, 5 A.

2. Can built-in external battery, lock time delay: 0 ~ 15 seconds. (Note: the battery is not including in the package, you should buy it in additional.)

3. Can be connected to an external remote control module, that can separate remote control lock for access control system.

4. Has over-voltage protection, over-current protection, and fault protection. The power supply will automatic shutdown protection if voltage less than 9 v .

5. Applicable to building intercom system, all kinds of inward and outward entrance guard controller, and all kinds of access control electric door lock.





Specifications:

1. Model: DYX-5A

2.Size: aprox. 212x173x70mm (L x W x H)

3. Input Voltage: AC 110 ~ 260 V / 50 ~ 60Hz

4. Output Voltage: DC 12 V / 5A

5. Time Delay: 0 to 15 seconds

6. Poder protection: short circuit/overload/over current over voltage protection

7. Poder: 50W

8. Operating Temperature: -20C~65C

9. Weight: 1.1KG





Package Include:

1 x Access Control Power Supply

1 x Manual

• 1. AC input: Ac 9 v ~ 260V, 50 hz ~ 260 hz, DC output standard:12 VDC, 5 A.
• 2. Support external backup battery 12V 7AH (Not included)
• 3. Set NC / NO outputs, can control various types of electric locks.
• 4. Has over-voltage protection, over-current protection, and fault protection. The power supply will automatic shutdown protection if voltage less than 9V.
• 5. Suitable for building intercom, various entrances access control, particularly suitable for all kinds of electric locks.

User questions & answers

Question:	Should the blue light stay on all the time, or will it go off after battery fully charged
Answer:	Instructions in package very easy to use
Question:	Does this work with NC magnetic lock
Answer:	You could use a single-headed nail. The template has a small built in recess at the edge so you can get a prying tool under there and loosen it up. Not quite as convenient, but not a show stopper.
Question:	Where can i get to read the manual for this libo model: dyx-5a
Answer:	Yes, this is a great jig. The only down side is, it has no place to storage the tiny pins and nails + the bit no last longer (depend on Router speed and kind of wood) 15 to 20 hinges.
Question:	If there is automatic reset when 1110v is restored, does the time delay work in that process as well as when 110v goes off and 12v is activated
Answer:	It is a very sturdy plastic

Product description

The 6202 kit is a four-door access control system with time and attendance. The kit comes with an outdoor IP66 Wiegand only reader and a no-touch exit button for each door plus a four-door network access control TCP/IP controller, doorbell siren, proximity cards, and key tags. The controller comes with software that provides time and attendance, real time of who came in and who came out, a reporting system to view all events and a door restriction system.

• Built for a safe access control system which allows for adding users to maintain access to your 4 doors application. Whether your registered user gains access through proximity key card or key tag, it will be updated in the reporting system.
• The doors can be unlocked to gain entrance by using the reader through key card or key fob (using the RFID built-in). To exit the door, the no-touch exit button connected will allow most locks (not included) to unlock.
• Personalized settings can be programmed based on date, time, and users. You can grant, limit, or deny access based on any parameters you input. The door will remain opened or closed as per the settings implemented.
• Additional doors can be added to the system. Depending on the number of doors to be added, you can purchase one, two, or four doors panel(s).
• VIS-3100: Outdoor IP66 Card Reader Only Compatible with Wiegand 26 Bit. VS-AXESS-4ETL: Four Door Network Access Control Panel System TCP IP Wiegand Desktop Software and Power Supply VIS-7013: No touch Request to Exit Button with Time Delay with LED Light, NC COM NO Outputs (10) VIS-APROXCARD: Prox Key Card (10) VIS-KEYTAG: Prox Key Fob. Installation manual provided.

User questions & answers

Question:	Does this support unlocking via building fire alarm system and if so how. (manual is not clear on alarm inputs wiring
Answer:	The advantage to using a router is that it has a plate on the bottom that will ride along the top of the Ryobi tool. The mortise will be cut to a specific depth, and that depth will be uniform, because the router is kept at the same height over the work. I've never tried using a drill, but it would seem to be very difficult to accomplish a uniform and controlled depth - which is critical to getting the door hung properly in the end
Question:	Where am I able to order more cards for this system
Answer:	Doubt it would most if not all metal doors come pre hung
Question:	What voltage electric door strike should we use with this system? 12v
Answer:	A router bit comes with this kit. It is sized for a 1/4 router collet.

Product features

Welcome to Visionis

The 6202 kit is a four-door access control system with time and attendance. The kit comes with an outdoor IP66 Wiegand only reader and a no-touch exit button for each door plus a four-door network access control TCP/IP controller, proximity cards, and key tags. The controller comes with software that provides time and attendance, real time of who came in and who came out, a reporting system to view all events and a door restriction system.



With Visionis, you get peace of mind. Our security systems are built with you, the customer, in mind. Our access control products are built with high standards for optimum performance and reliability to ensure your satisfaction. The mindset at Visionis is to combine a modern feel with the inventive ingenuity. This allows us to provide you with a product that gives and maintains its quality and protects you all at once. Visionis is simply technology within your reach.



Before purchasing, it is recommended that the customer checks with their local fire authority to see if there is any additional product they may need in order to comply with the local fire codes. We are not responsible for the improper installation of our product(s) or any type of fees that can be incurred by not complying with your local fire authority.



We recommend that at the time of install, you set everything up on a work bench to make sure everything is ready to go before. These products and their user-friendly design will have you secured and protected very soon!

• Includes CD software
• Power supply and power cord included
• Install wires are not included
• This software is not compatible with MAC computers, only with Microsoft.

Security Built for You

Get Secured

Know Your System

The reader is a slim Wiegand output proximity reader. It is waterproof and works with IP66. It has Wiegand 26-37 bits output with a default of 26 bits. You can only use EM cards with this product. Mifare cards and other types of cards may not be compatible. It has reading range of 7cm (2.75 in.) and a working temperature ranging from -40F to 140F. The proximity cards and key tags in this kit can be programmed to the reader quickly to use right away. If you need more, you can always order extra cards or tags.

• Color: Black
• Operating Voltage: 9~24V DC
• Frequency: 125KHz
• Card Type: EM card
• Reading Distance: 7 cm (2.75 in.)
• Output Format: Wiegand 26 bits (26~37 bits available upon request)
• Operating Temperature: -40°C ~ 60°C (-40°F ~ 140°F)
• Standby Current: < 25mA
• Operating Humidity: 10%~95% RH
• Index of Protection: IP66
• Dimensions: 102L x 48W x 20H (mm) – 4.01L x 1.88W x 0.78H (in.)

Product description

Features of access board:

Communication: TCP/IP

Software Supportable Database: Access & SQL

Power Supply Input: DC/12V

Input Format of Reader: Wiegand 26-40 bit (All 125KHz or 13.56MHz card reader with compatible protocol)

Quantity of Readers: 4 units

Door Controlled: 4 door (Get in the door by swiping card, and get out door by button)

Quantity of Users: 20,000 users

Quantity of Event Buffers (offline): 100,000 event buffers

Max Distance from Reader to Controller: 100m/328ft (suggestion distance 80m/262ft)

Alarm for Long Time Door Open, Unlawful Entry, Intimidate

Fire and alarm linkage: If no connection with the expansion board, only has software interface alarm, and drive the computer speaker. If connected with expansion board, is able to alarm by hardware, if connected with strengthened expansion board, then is able to Security alarm

Compulsive open and close door at long time: Yes

Open door in remote distance: Yes

Inter block: Yes

Anti pass back and tail: Yes

Multi card open door: Yes

Open long time at specified time: Yes

Urgency locking: Yes

First card unlocking: Yes

Features of power box:

Built-in reverse surge protection and Short-circuit protection function

With charge and discharge function,can add a 7AH 12V lead-acid battery,can meet the needs of an electric mortise lock,a card reader and a controller to work 35 hours after power failure (External battery not included)

Setting automatic protection function, built-in fuse

Two +12V and two GND terminals

Specifications of power box:

Input: AC110V/60Hz

Output: DC12V/3.5A

Power: 40W

12V/24V Adjustable Output: No

Size: 371Lx259Wx78Hmm

Weight: 3.3Kg / 5.5lb

Package:

1 x Access Control Board

1 x Power Supply Box

1 x CD

• ✅Input Voltage: AC110V (Power's Transformer with UL-Recognized)
• ✅Control of memory up to 20,000 user / Up to 100,000 event buffers
• ✅Network communication via TCP/IP
• ✅Input Format of Reader: Wiegand 26-40 bit (All 125KHz or 13.56MHz card reader with compatible protocol)
• ✅Software Supportable Database: Access & SQL

User questions & answers

Question:	We have a shop with irregular hours. Can an external signal, such as a manual switch keep open and disable the tamper sensor
Answer:	Yes, it will work with both NC lock and NO lock.
Question:	How many controllers can i have on one lan and all still work together
Answer:	We will send the user manual together with the device. If you want to see it in advance, please contact our Customer Services.
Question:	Can a 12V lithiun ion battery be used instead of a lead acid battery
Answer:	Don't need to worry about this problem.
Question:	How do I wire mag locks to the professional grade controller? I'm used to 12+/- for power and 12v+/- for locks and daisy chaining th
Answer:	I am not sure which is the small bore attachment but I have used to of them and it works just great and I really love this tool!

Product description

SAFEGUARD SUPPLY ERA SERIES - UNPARALLELED WIRELESS RANGE & SIGNAL STRENGTH>b>

The ERA-UTDCR wireless doorbell for office & home utilizes cutting edge technology which allows the signal to penetrate materials such as metal, reinforced concrete, brick, stone, stucco, glass, steel, and other restrictions typical wireless door bells have issues with. The range is field tested at up to 4000' - NOT line of sight but passing through the aforementioned objects - even through separate buildings not attached to the structure. The push button is made of thick, durable & waterproof ABS material that provides durability & is able to be painted to the color of your liking.



HOME & COMMERCIAL DOOR CHIME THAT ALLOWS YOU TO ADD 12VDC COMPONENTS TO HELP YOU MEET YOUR NEEDS

Do you have a home that needs a loud wireless doorbell to cover all areas of your house either inside or out? Do you need a doorbell for the hearing impaired? Are you a convenience store, retail store or business in need of a commercial doorbell entry alert chime where the door chimes when door opens for business in noisy environments such as a warehouse, manufacturing or plant facility? This unit has a receiver which 12VDC contacts to power virtually any 12VDC accessory such as a firebell, buzzer, strobe light, siren, etc). It also C relay. The wireless transmitter has N/O, N/C relay that can be used with other devices that are self powered.



Specifications

Range: Up to 4000 ft Sounds: 12 Tunes Volume: Adjustable Knob Control (0db - 95db) Receiver Power: Plug In Class 2 UL LISTED AC Transformer (120v 60Hz 18Watts) Receiver Outputs: 12VDC, N/O, N/C Relay Transmitter Power: 1 x 3V CR2 battery Transmitter Outputs: "C" Relay



Package Includes 1 x Push Button Transmitter 1 x Door/Window Contact Sensor 1 x Plugin Chime Receiver 4 x Screws 1 x 3V CR2 battery 1 x User Manual

• 🔔 INCREDIBLY STRONG, POWERFUL & LOUD DOORBELL: Heavy duty, waterproof wireless door chime transmitter signal penetrates objects that other long range wireless doorbell systems simply can't - even travels through several reinforced concrete walls as well as separate buildings. Adjustable volume control from mute up to 95db. Effective even in the largest homes & commercial buildings.
• 🔔 DUAL FUNCTION TRANSMITTER: Can be used as a typical Doorbell Chime push button or as a magnetic door chime where door chimes when door opens making it perfect for a retail door chime, store door entry chime, gate alert, warehouse doorbell or even window alarm.
• 🔔 INTEGRATION WITH 12VDC DEVICES REGARDLESS OF MANUFACTURER: Only this wireless door chime gives you the ability to add 12VDC devices (strobes, buzzers, sirens, bells, etc) with 12VDC outputs - 1 per each of the 4 zones. Transmitter features N/O, N/C relay & plug in receiver has “C” relay.
• 🔔 EXPANDABLE, CONFIGURABLE & SIMPLE INSTALLATION: Easily pair an unlimited number of transmitters to a receiver - each receiver has 4 zones, allowing for one of 12 melodies per zone. Easy, hassle-free pairing transmitter to receiver.
• 🔔 A WIRELESS DOORBELL FOR HOME OR BUSINESS WITH COUNTLESS USES: Door announcer, call button for elderly, magnetic door entry alert security contact sensor for gates & windows, classroom doorbell, wireless panic button to alert one or multiple rooms or locations far away.

User questions & answers

Question:	Do you sell a receiver alone? We want to add to our unit we just purchased. Only need one doorbell but two receivers for different parts of building
Answer:	Hello Randall, the N505AUTM/ST contains one switch and one magnet. The picture simply shows the different configurations ... cable up/down or left/right you will have no loss of gap. Best regards, Nascom
Question:	Can I put more than one transmitter on a doorbell
Answer:	I went to Google and found your answer - https://www.nascominc.com/index.php/lanotattachments/download/file/id/95/store/1/n505autm_1.pdf
Question:	Is it likely to work within a distance of 500m, with houses in between and 10m altitute difference
Answer:	yes, it has only 2 wires
Question:	Can I chain multiple receivers together to extend the range even further
Answer:	Switch is normally closed when lined up with magnet.

Product features

A Powerful & Versatile Door Chime That Will Surpass Your Expectations

COMMON APPLICATIONS

• Residential Dwellings - Homes, Apartments, Condominiums, Manufactured Housing, Townhouses, Duplexes
• Retail Establishments - Chain Department Stores, Convenience Stores, Salons, Pizza, Ice Cream & Sandwich Shops, Auto Parts Stores
• Industrial Facilities - Warehouses, Manufacturing & Production Facilities, Construction & Supply Yards, Labs
• Government - Schools, State & Federal Facilities Police & Fire Departments, Military Installations, Public Buildings & Parks
• Business - Banks, Offices, Mom & Pop Small Town Businesses
• Secured Areas - Money Rooms, Storage Rooms,Sensitive Inventory

STANDARD PUSH BUTTON OPERATION

When a visitor pushes the doorbell, chime receiver will sound instantaneously. Button is completely weatherproof & can be painted

MAGNETIC DOOR CONTACT OPERATION

When used as a door or window contact, you will be immediately notified when someone opens the door or window

PANIC TRANSMITTER OPERATION

Immediate notification when transmitter is activated to alert others

Product description

DC12V 3A/ 5A Access Control Power Supply

very suitable for door access control system and video intercom system



Product Features:

1. This DC12V power supply with 3A and 5A, white and black color optional.

2. With Control, Push, GND, DC12V, NC, NO port, can be work with all kinds of electrick locks.

3. With 0-15 seconds time delay adjustable.

4. Working input valtoge of AC90-260V, more freedom.

5. Made of metal, high quality.

6. Looks very pretty

7. Less Power consumption, and high power. Small switching transistor



Kindly note: 3A can control 1 electric lock, 5A can control 2 electric locks.

Small and sturdy body

Cast-iron paint power supply shell, drop-resistant and impact-resistant, sturdy protection circuit board, side heat dissipation design, stable and safe continuous operation.

New upgrade stabilizing transformer

High-power stable transformer, using high-quality copper wire, more stable use, output power can meet access control, electric mortise lock / magnetic lock work at the same time.

Delay adjustable

New upgraded power delay design, adjustable time is 0 ~ 15 seconds



Products include:

White 5A Power Supply*1

• Access Control Power Supply Transformer Door Access Control system Switch Power Supply 3A 5A AC90-260V High Quality.
• Cast-iron paint power supply shell, drop-resistant and impact-resistant, sturdy protection circuit board, side heat dissipation design, stable and safe continuous operation.
• High-power stable transformer, using high-quality copper wire, more stable use, output power can meet access control, electric mortise lock / magnetic lock work at the same time.
• Delay adjustable.New upgraded power delay design, adjustable time is 0 ~ 15 seconds
• 3A can control 1 electric lock, 5A can control 2 electric locks.

Product description

SAFEGUARD SUPPLY ERA-DOOR ANNOUNCER DOOR MOTION SENSOR CHIME FOR BUSINESS

The ERA-DOOR ANNOUNCER is a highly reliable, durable and extremely simple to use & install motion detector door bell sensor for business that was exclusive to select large convenience, retail, fast food & sub sandwich stores. Safeguard Supply has made this door chime motion sensor is available to everyone. It is simple to install & requires no maintenance. This door sensor unit produces a non-offensive sound to notify you that someone has entered or passed through the monitored zone.



ENTRANCE ALERT DOOR CHIME OPERATION:



Simply install a 9V battery (not included), select the desired chime sound (or use default setting) & mount the wireless motion sensor door chime over the entry way using the included mounting bracket, adjust the lens angle to cover the area you want to cover. When the wireless door sensor with chime detects the combination of movement & heat (passive infrared, PIR) it triggers the unit to emit a sound. This wireless doorbell system works great for door that aren’t always closed or a hallway area where a contact entrance sensor could not be used. With this product, the sound emits from the device itself using the enclosed speaker.

Another feature of this product that distinguishes it from other PIR sensors on the market is the unique mounting bracket that allows you to tilt the sensor lens approximately 160 degrees to ensure the invisible beam covers the area you want to pick up. For example, in a retail store, you may want to rotate the unit so that the lens is angle in towards the door to minimize “bleed” into area with a lot of foot traffic.



PRODUCT FEATURES:

* 3 Sounds

* 4 sound levels to 95dB

* Low Battery Indicator



THE ERA-DOOR ANNOUNCER BUSINESS DOORBELL INCLUDES:



1 X All In One PIR SENSOR WIRELESS DOOR ENTRY CHIME UNIT

Bracket & Screws

Manual

1 Year Warranty

• 🔔 Self Contained & easy to use motion sensor doorbell alert system chimes immediately at the door when customers walk in
• 🔔 Dependable wireless door chime for business entrance alert requires no wiring, no programming, & works even when power goes out
• 🔔 Do It Yourself maintenance free wireless entry alert chime for business with long life battery can be installed in a minute
• 🔔 Coveted for it's simplicity & reliability, this USA designed PIR commercial door buzzer was previously only available to select fast food, sandwich & convenience stores
• 🔔 Extremely Inexpensive yet highly effective industrial grade motion door chime door annunciator is backed by a 1 year full replacement warranty

User questions & answers

Question:	can you set it to quiet? I just need a gentle note when my wife walks in behind me in the home office so she doesn't startle me
Answer:	No, the work indicator will not go off. But when the battery is fully charged, it will automatically stop charging.

Product description

SAFEGUARD SUPPLY WIRELESS ENTRY ALERT CHIME FOR BUSINESS SERIES - THE ERA-MOTION DOOR CHIME WIRELESS DOOR BELL ALARM:



The ERA-MOTION DOOR CHIME is a wireless motion sensor door chime that's designed to monitor all types of entrances, even those where the door sometimes remains open. This doorbell alert system is an ideal door bell for office, retail stores, convenience stores, & warehouses. It also provides coverage in open areas & narrow areas such as hallways, dock doors, asiles, sensitives areas, etc. When someone walks through the door chime motion sensor detection area (such as a entry door, customer waiting area, dressing room, check out lane, dock door or virtually any area where the entry sensor is located) the ERA-PIR wireless door sensor transmits a signal up to 4,000' away to the ERA-DCRX wireless entrance alert door chime receiver. Each ERA-DCRX plug in receiver is capable of pairing with four entrance sensor transmitters per zone. You may add as many entry chime receivers as needed. Each zone will play 1 of 12 melodies you assign to the zone so you can easily distinguish which door opening chime sensor was activated. For example, you may program zone 1 to a door or area and have it play a simple ding-dong sound, while zone 2 is programmed to a different location which plays the Westminster Chime sound. The receiver features a volume control button allowing you to turn the unit off, mute the unit, and set to four different sound levels, with max sound approximately 95 dB. In addition, each zone on the receiver features a live 12V DC output that allows you to add sirens, strobes, firebells, and buzzers to increase the sound or add bright visual indicators. The receiver also features 1 x C-form relay assignable to any combination of zones.



BUSINESS DOORBELL KIT:



1 x Motion Doorbell Sensor

1 x Commercial Door Bell Wireless Receiver

1 x Manual

1 x Mounting Bracket & Screws

1 x 1 Year Warranty

• 🔔 The ERA-Motion Door Chime commercial door buzzer incorporates the latest technology that other inferior entrance chime door annunciator units do not, making it the ideal door bell sensor for business
• 🔔 A long range wireless doorbell 4000' signal penetrating reinforced concrete, wood, steel, stucco, metal which traverses multiple walls, floors & even unattached buildings
• 🔔 Unique passive infrared door motion sensor chime technology which eliminates most false alarms caused by other inferior entry alert chime systems
• 🔔 95dB Loud door chime plug in receiver with 12 melodies & volume control that can be adjusted to be heard in the quiet offices or the noisiest warehouses.
• 🔔 Unlike other wireless door entry systems, the ERA-PRDCR commercial door chime can function as a powerful door bell alarm out of the box or futher expand the system, take advantage of the form-c relays or add 12VDC accessories

User questions & answers

Question:	If I bought 2 of these, would both alarms go off if only 1 door is opened? I have 2 doors and 2 different locations
Answer:	Thank you for your question. Please see our variety of different packs of Proximity cards: https://www.amazon.com/s?k=Proximity+cards&me=A2NZ38D3X8QI1T&ref=nb_sb_noss
Question:	Stupid question but the instructions say to remove the four screws on the back of the receiver to replace the battery? No screws. How do you do it
Answer:	Thank you for your question. Yes, 12Vdc.

• Developed and designed by Visionis, this 2 door access control panel allows you to monitor up to two doors in your system. Depending on what type of keypad or reader (not included) you have connected, the panel can read fingerprint, pin code, key card or tag (via RFID).
• Users can be registered to gain entrance. All activity will be recorded and accessible in the reporting system via the software.
• Software will allow to personalize settings for each user based on date and time. You can grant, limit, or deny access based on the information set. Detailed information provided in the manual.
• Additional doors can be added to the system. Depending on the number of doors to be added, you can purchase one, two, or four doors panel(s).
• Metal box is included. 12V 8.5 Amp Power supply included. Power cord included. Circuit breaker switch included. Tamper switch included. The software is not compatible with MAC computers, only with Microsoft.

User questions & answers

Question:	Does this come with door magnets and card swipes
Answer:	I currently have 6 and they all work great
Question:	Do I need a computer with the software running 24-7 to use this board in order to work properly
Answer:	12V lithiun ion battery could do the job.thanks.
Question:	Can I use an electric strike instead of Magnetic Lock
Answer:	As to the wiring between the power supply and magnetic lock, please refer to the below link: https://www.amazon.com/vdp/f9f1f63ac6504c17bd4d32cb46b88468. Thanks.
Question:	Can i add multiple door open periods for a single day? such as open from 8am - 9:30am then again from 11am til noon and 5pm til 9pm
Answer:	Dear customer, There is an alarm input that you can put it with the alarm system but since we do not sell fire systems we can not support it. Thnank you

Product features

Welcome to Visionis

With Visionis, you get peace of mind. Our security systems are built with you, the customer, in mind. Our access control products are built with high standards for optimum performance and reliability to ensure your satisfaction. The mindset at Visionis is to combine a modern feel with the inventive ingenuity. This allows us to provide you with a product that gives and maintains its quality and protects you all at once. Visionis is simply technology within your reach. We offer free tech support in English and Spanish.

Security Built for You

Get Secured

Product description

SAFEGUARD SUPPLY ERA-PORTABLE DOORBELL - DOOR DINGER FOR BUSINESS & HOME ENTRY DOOR BELL



This door entry chime for business & home entrance alert can be used as a push button where someone pushes a button to ring the portable chime receiver or as a door contact alarm where the door chimes when door opens.



This battery operated door alarm is a completely wireless doorbell kit needing no wiring, no plug in, and no external power source. The entrance chime weatherproof transmitter operates on a long life battery and the entrance door chime portable receiver operates by a rechargeable battery which included a USB cable & plug in brick. 6-7 day battery standby time depending on usage.



The wireless portable doorbell receiver can be set to vibrate, sound only, or vibrate & sound mode with 12 melody selection & adjustable volume to 80dB. If you happen to miss a alert, the portable door bell stores a time & event log. A LED backlight is activated when triggered



Although this unt was designed as a commercial door bell to pass through structures, multiple walls & floors that your typical imported wireless doorbell cannot, it's also very useful in large homes at a fraction of the cost to have an electrician wire an expensive solution. This unit has 3/4 to 1 mile operating range allowing the signal to pass through reinforced concrete, block, brick, stone, metal & steel.



The ERA-PORTABLE DOORBELL system can be used with any Safeguard Supply ERA series wireless transmitters (push button, door contact, driveway sensor, indoor motion alert and receivers). It can easily be expanded to fit your needs from very basic to sophisticated. Regardless of use, programming is straightforward and uncomplicated.



WIRELESS DOORBELL KIT INCLUDES:



1x ERA-UTX Push Button (3.38"x1.94"x0.81") / Contact Sensor (2"x0.56"x0.38")



1 x Portable Battery Operated Receiver (4"x1.5"x0.75")



1x Seller 1 Year Replacement Warranty

• 🔔 PORTABLE DOORBELL THAT PACKS A PUNCH 4"X1.5" DESKTOP, POCKET OR CLIP ON USE: you will instantly be alerted by 4"chime and/or vibrating notification with mute & volume control to 80dB
• 🔔 POWERFUL BATTERY OPERATED DOOR BELL WITH NO WIRING, NO OUTLETS & NO COMPLICATED PROGRAMMING: Completely wireless battery operated door chime kit includes receiver and weatherproof push button & door contact sensor
• 🔔HERCULEAN STRENGTH FOR USE IN LARGE HOMES & CONDOS, WAREHOUSES, HOSPITALS & MANUFACTURING FACILITIES: Signal penetrates reinforced concrete wall, block, metal, steel, brick & traverses multiple walls & floors
• 🔔 DON'T BE LIMITED BY GENERIC LOWER QUALITY & PRICED ENTRANCE ALERT IMPORTS: Powerful enough for use as a business doorbell yet effective enough for a hearing impaired door bell for the deaf as well as extremely noisy locations
• 🔔 ENGINEERED, SOLD & SHIPPED WITH PRIDE FROM A USA SMALL BUSINESS: Looking for a business door chime or a entry door chime for your home, we develop every Safeguard Supply product in house with pride and use them on a daily basis in our North Georgia veteran owned business.

• Main advantage is: Can remotely open door easily for visitor, It's No need walking to door to open Lock, Just a simple press on the remote control button. Include totally 3 remotes, and can easily add more.
• Remote open distance is about 100 feet. Press button to let visitor in, simple and very convenient.
• 600lbs force electric magnetic lock, Also include Z+L bracket, can install for both Inswinging or out-swing door.
• With professional power unit(100-240V input, DC 12V/3A output) to power on the whole system, door open time can be adjusted; With Metal push to exit button, just press it to open lock when going out.
• Provide detail video guide/wire diagram/manual, also provide live support for ever, you can easily setup this system.

Product features

600lbs Magnetic Lock Open Door Inward and Outward 1 Door Access Control Systems with 1 for 3 Remote Control +ZL Bracket +110V Power Unit +Exit Button

Power Supply:

• This AC 110V--240V Power supply controller is a transformer which provides stable output voltage for remote access controller, lock.
• Can reduce the load of access controller,save wiring to reduce the hidden trouble.
• Set NC/NO outputs, can control various types of electric locks.
• Based delay control circuit, lock time can be in 0-15 seconds.
• The circuit board has remote control port.
• Input Voltage: AC 110~220V
• Input Frequency:50-60Hz
• Output Voltage: DC 12V/3A
• Adjustable Locking Delay:0-15sec
• Dimension: 5.43L x 3.62W x 1.50H(in)/138L x 92W x 38H(mm)

Wireless Receiver:

• Channels :1 Channel
• Operating Voltage :12V
• Static State Work Current :< 6mA
• Received Sensitive :-105dBm
• Max Input Current :< 10A

Electric Magnetic Lock:

• Voltage/Current: 12V/500mA
• Lock body size: 9.84L x 1.89W x 0.98H(inch); Plate size: 7.09L x 1.50W x 0.47H(inch)
• It is a high-performance 600lbs holding force electric magnetic lock which suit for many access control system.
• NC mode(Locked while supplied with power).
• Performance testing: 1000000 times aging test.
• Suitable for :wooden door, metal door, etc.
• Safety function: built-in voltage spike suppressor
• Anti-residual magnetism designed.Design without mechanical failure.MOV provides reverse current protection.
• High strength stainless steel material,anodized aluminum housing.
• Dual insulative housing increase the holding force.

Transmitter (Remote Control):

• Material :plastic
• Color : gray
• Range :approx 60 ~ 100 feet

Metal Push to Exit Button:

• Dimensions: 80Lx30Wx23H(mm)
• Standard Structure: alloy panels, metal buttons
• Electrical performance: 3A @ 36VDC
• Contact output: NO / COM contacts
• Temperature: -20 ~ +50oC
• Suitable Humidity: 0 ~ 95% (relative humidity)
• Panel processing: alloy panels, high temperature paint echanical Life 500000 tests
• Weight: 0.1kg

Product description

Electric Strike Remote Unlock, TMEZON Narrow Type Electric Door Lock with Power Supply Control for Home Office Wood Metal Door NC Mode Fail Safe DC 12V Access Control & Audio Video Door Phone Intercom Systems

• 【Multiple scope use】This lock applies to office buildings,wooden doors,stainless steel doors, fire doors,residential Entrance doors,Intelligent electric cabinet,storage cabinet and anode mechanical lock or ball-type supporting the use of locks.
• 【Easy installation and Product Benefits】embedded and easy installation,beautiful appearance. The electromagnetic part of the selection of high-quality magnetic materials and built special treatment, long hours does not produce residual magnetism to ensure normal use.
• 【Specification standard】There is CE Certificate by European Union and testing to 1000000 cycles, holding force up to 500 kg. Don't need to worry the safety of home or office.

• Control 1 door, get in the door by swiping card or key fob, and get out door by push to exit button. Can store/download/check entry records and generate report by professional management software.
• Control of memory up to 20,000 user / up to 100,000 logs. Auto open/close at any pre-set time during any day. Support "who" can enter which door at certain time, authorized access control.
• The FRID reader is waterproof, less than 0.2 second response speed, 5-10cm proximity range.The electric magnetic lock is with 600lbs/280kg holding force.Powerful IP Management Software.
• Have smart phone APP to open lock remotely.App operate system: iOS & Android.Desktop USB reader,read card number into software so that easy programming/register user. Detail video guide and wire diagram make all easily, you can DIY.
• Network communication via TCP/IP. Software Supportable Database: Access & SQL Server. Support win7/win8/win10 both 32 and 64 bit system.

User questions & answers

Question:	what app does this use? Can I have multiple doors
Answer:	You can regulate the volume. I am assuming that the lowest volume setting is very quiet.
Question:	Can the rfid reader log which card opened the door at what time? can i use my own programmable rfid cards? does the software include access controls
Answer:	Yes, you can add a an external shunt switch but, adjusting the door schedule in the software application is, by far, a better solution...

Product features

1 Door Access Control System with 600lbs Magnetic Lock 110V Power Supply Box RFID Reader Push Exit Button USB Enroll Reader RFID Card & RFID Key Fob

• Basic funtion: swipe card/key fob open door.
• Easily add/delete/activate/disable the user open privilege by professional management software.
• Support phone app to open door locally or remotely.
• Can be used for high security area, the control board as master unit is put inside room.
• Can check/download/export the detail history entrance record.
• Allow access for certain door at certain time for different users.
• Can keep door auto open during business hour and then auto close at set time.Support holiday security control.
• Can swipe certain times to keep open and swipe certain times to close door.
• Can be used for user attendance check also.
• A lot other features such as anti-pass back, 1st card open, multi-card open .etc.
• ......

Power Supply Box:

• Power：60W
• Rated Current：5A
• Input Voltage：110V-240V, can be used all over the world.
• Output: DC12V to power on the whole System(11－14V can be fine-tuned).
• Color of the box：black
• Size of the box：279mm * 234mm * 67mm
• Also act as the cabinet for the control board.
• With power cable to insert to electric outlet box.

1 Door Network Access Control Panel:

• Control 1 door,get in by swipe card/key fob, input PIN code or use card + PIN, and get out door by exit button.
• Door controlled : 1
• Support 1 or 2 readers.
• Control of user capacity up to 20,000 user / up to 100,000 history records.
• Network communication via TCP/IP.
• Access control management software includes all-in-one-card management system, such as normal shift and multi-shifts time attendance management system,meeting attendance management system,ect.
• Application software support win7/win8/win10 32bit and 64 bit, not support MAC.
• Support web interface(no advanced control, can add/delete user and check records .etc basic function).
• Support phone app to open door even you are not there.
• Record never lost in case of power failure.

Electromagnetic Lock:

• Voltage/Current: 12V/500mA
• Lock body size: 9.84L x 1.89W x 0.98H(inch); Plate size: 7.09L x 1.50W x 0.47H(inch)
• It is a high-performance 600lbs holding force electric magnetic lock which suit for many access control system.
• NC mode(Locked while supplied with power).
• Performance testing: 1000000 times aging test.
• Suitable for :wooden door, metal door, etc.
• Safety function: built-in voltage spike suppressor
• Anti-residual magnetism designed.Design without mechanical failure.MOV provides reverse current protection.
• High strength stainless steel material,anodized aluminum housing.
• Dual insulative housing increase the holding force.

RFID Reader:

• Size:101x43x16(mm)/3.98x1.69x0.63(inch)
• Less than 0.2 second response speed, 5-10cm proximity range.
• Built-in antenna & LED (double color LED) & loud speaker (buzzer).
• DC 9V-16V working voltage,standard 12V; 70mA working current.
• Real time data transfer.
• It's water-proof.

Push to Exit Button:

• Mechanical Life: > 500000 times
• Operating Temperature: -20C ~ 55C
• Panel Material: Hard Plastic
• Dimension: 86Lx86W(mm)
• Easy wire, just connect the two contacts to P1/GND for DOOR1, P2/GND for DOOR2 ...

• Control 4 doors, get in the door by swiping card or key fob, get out door by push to exit button. Can store/download/check history entry records and generate report by professional management software.
• Control of memory up to 20,000 user / up to 100,000 logs. Auto open/close at any pre-set time during any day. Support "who" can enter which door at certain time, authorized access control.
• The FRID reader is waterproof, 5-10cm read range. The electric magnetic lock is with 600lbs holding force. Control board is TCP/IP based communication, provide professional designed power cabinet box.
• Have smart phone APP( iOS & Android) to open door remotely. Desktop USB reader,read card number into software so that easy programming/register user. Detail video guide and wire diagram make all easily, you can DIY.
• Network communication via TCP/IP. Software Supportable Database: Access & SQL Server. Support win7/win8/win10 both 32 and 64 bit system.

User questions & answers

Question:	Is it possible to add this hardware to a System Galaxy software
Answer:	Yes, I use an electric strike and not magnets. I use fail secure strikes so power is sent only when its needed to be opened.
Question:	How many volts run from the control panel to the magnetic lock? Is it low voltage or does an electrician need to wire it
Answer:	yes
Question:	What if in 3 years I need new key fobs? What frequency is it or what type of replacements can I get for this system
Answer:	You can have it either way. Each transmitter can be set to one or both receivers. If set to one, then only that receiver will sound the alarm when the matching transmitter triggers. If set to both, then both receivers will sound the alarm. It is your choice.
Question:	we have 12 doors that we want access control on. can we link 3 of your systems together
Answer:	The user manual it reads "Remove the screw located on the backside of the case using a Phillips head screwdriver (see figure 1). Once the screw is removed, open the case". Are you sure you are looking at the right manual?

Product features

4 Doors Access Control Systems with 600lbs Magnetic Lock 110V Power Supply Box RFID Reader Push Exit Button USB Enroll Reader RFID Card & RFID Key Fob

• Basic funtion: swipe card/key fob open door.
• Easily add/delete/activate/disable the user open privilege by professional management software.
• Support phone app to open door locally or remotely.
• Can be used for high security area, the control board as master unit is put inside room.
• Can check/download/export the detail history entrance record.
• Allow access for certain door at certain time for different users.
• Can keep door auto open during business hour and then auto close at set time.Support holiday security control.
• Can swipe certain times to keep open and swipe certain times to close door.
• Can be used for user attendance check also.
• A lot other features such as anti-pass back, 1st card open, multi-card open .etc.
• ......

Power Supply Box:

4 Doors Network Access Control Panel:

Electromagnetic Lock:

• Voltage/Current: 12V/500mA
• Lock body size: 9.84L x 1.89W x 0.98H(inch); Plate size: 7.09L x 1.50W x 0.47H(inch)
• It is a high-performance 600lbs holding force electric magnetic lock which suit for many access control system.
• NC mode(Locked while supplied with power).
• Performance testing: 1000000 times aging test.
• Suitable for :wooden door, metal door, etc.
• Safety function: built-in voltage spike suppressor
• Anti-residual magnetism designed.Design without mechanical failure.MOV provides reverse current protection.
• High strength stainless steel material,anodized aluminum housing.
• Dual insulative housing increase the holding force.

RFID Reader:

• Size:101x43x16(mm)/3.98x1.69x0.63(inch)
• Less than 0.2 second response speed, 5-10cm proximity range.
• Built-in antenna & LED (double color LED) & loud speaker (buzzer).
• DC 9V-16V working voltage,standard 12V; 70mA working current.
• Real time data transfer.
• It's water-proof.

Push to Exit Button:

• Mechanical Life: > 500000 times
• Operating Temperature: -20C ~ 55C
• Panel Material: Hard Plastic
• Dimension: 86Lx86W(mm)
• Easy wire, just connect the two contacts to P1/GND for DOOR1, P2/GND for DOOR2 ...