13 best canoe fish finders

Product description

Following in the success of the STRIKER fish finder series, Garmin is proud to announce the new STRIKER fish finders with ClearVü technology. These devices are designed to allow you to mark your favorite fishing spot and easily navigate back to it tomorrow, saving you time and money. STRIKER series fish finders are available in 3.5-, 5- and 7-inch display sizes.Display resolution:480 x 320 pixels

• The power of simple - offers a keyed interface with dedicated buttons. The device is easy to use and easy to install. Available in 3.5-, 5- and 7-inch display sizes.
• Waypoint map - use the waypoint map to easily view, mark and navigate to locations such as brush piles, stumps and docks.
• Chirp sonar - chirp sends a continuous sweep of frequencies which provides a wider range of information. Chirp sonar is able to create crisper fish arches with better target separation.
• Built-in flasher - view your sonar data in the classic flasher format; Ideal for ice fishing or vertical jigging.

User questions & answers

Question:	does it come with the fish finder or is it just the bag and other items
Answer:	It comes with everything you need,the bag, the holder,the battery, the charger,the fish finder with gps tracking, and instructions
Question:	Will this unit show bait fish
Answer:	only if there is big schools
Question:	Planning on having this stricly portable from boat to boat, is it easily installed and removed? Or is drilling required
Answer:	I've take one with me up to Alaska for the last 8 years. Setup is about five minutes on the 14' Lunds we rent up there.After the first time, the transducer cable length is established so stuff it in the side pouch at the end of the day. The rest of the cable stays wrapped up on the hanger inside the portable unit.The unit is very stable and sits nicely on the bench in front of me, even in the bumps.I keep a Scotchbrite pad in another pouch on the unit. Scrub a spot on the transom before sticking the suction cup on.I keep some tiewraps in the side pouch. Use a tiewrap to tie off the transducer cable to something on the boat. The suction cup holds up to 20 mph... until it doesn't. Tiewrapping the cable to the boat keeps the transducer out of the prop.
Question:	What does the bundle come with? Battery? Tranduser for ice fishing
Answer:	STRIKER 4 Dual-beam transducer Tilt/swivel mount Portable bag Base/handle Suction cup mount Foam float Kayak In-hull Transducer Mount Power cable Rechargeable battery AC charger Documentation
Question:	Please i need a trasceduser cable replacement. How much will it cost me
Answer:	Usually we didn't sell the transducer alone. If you already bought fish finder from us before, please contact us through amazon message and we will give you the offer for the transducer alone.
Question:	It works in salt water
Answer:	Yes,this Lucky fish finder can work well in salt water. It is suitable for ocean、lakes and rivers. Hope this helps.
Question:	can you mount the transistor in side the kayak
Answer:	Usually people will fix the transducer on the hull of the kayak (the outside). Because the transducer can only be working when it touches the water.
Question:	Does it work well for ice fishing
Answer:	Yes it works well for ice fishing, although you must drop the transducer below the ice in order for it to read depth accurately. I also found that it has the potential to mis-detect large tube jigs as a fish, but I actually don’t mind that as it tells me how deep my bait is. I also use this with my kayak mounted with the bracket, so I get double duty. Battery life is fantastic even in below zero temps. I’ve been out with it on several outings below freezing and I’m still on the same set of batteries! I would recommend this product.
Question:	What's the RMS on these subs
Answer:	I think it’s 1200 but i am not sure. I have four of them running at 2ohms with a planet audio torq 5000.1 amp. One of the loudest trucks in town.

Product features

Function

• Well understand the water depth and fish location by the portable fish finder.
• The fish finder portable gives you alerts when fish and fish schools passing by.
• 5 modes sensitivity options enable you to use the kayak fish finder in different fishing environments.
• The kayak fish finder can be used in different ways, such as on ice, fixed to kayak, put it into a hole or float it on water surface.
• You can understand the composition of the bottom contour. Sands, rocks and weeks will be shown on the LCD display.

Specification

• 2inch TN/ANTI-UV LCD Display.
• Blue LED Back lighting.
• Measurement Unit: FT/M
• 1.81inch diameter transducer sensor.
• Detect Depth Range: 3ft~328.08ft (0.6m~100m) under sensor.
• Sensor coverage range: 45 degrees beam angle in 200Khz.
• Sensor Operating Temperature: 14°F to 122°F(-10°C-50°C) .
• Cable Length: 25ft (7.62m)
• Powered by: 4 x AAA batteries (not included)

For Kayak Fishing

1. Attach the Side-Scan Adapter to the boat hull using the mounting tabs.
2. Break though the hull of a boat. Place the fishing sonar sensor against the hull bottom 1 inch underwater.
3. The moving speed of kayak should be below 5mph.

For Ice Fishing

1. You should clear the snow on the ice layer. Make sure the surface is smooth enough. Put the LUCKY fish finder portable directly on ice layer to detect fish distribution in purpose of selecting a place to drill a hole.
2. There should be no air between the sensor and the ice and no air between ice layer and the underwater either. Otherwise, the portable fish finder will not work properly.
3. Cut a hole through the ice and put the fishing sonar sensor directly in the water. Enjoy the fishing gear

For Shore Fishing

1. Fixed the removable float on the cable.
2. Cast the fishing sonar transducer into water as far as you can.
3. You can cast the fishing sonar transducer either by your hand or by the fishing rod.

STRIKER 4 Portable Bundle

3.5-inch CHIRP Fishfinder with GPS and Portable Kit.

Navigate Easily with Waypoint Map

Since the STRIKER fishfinder series includes high-sensitivity GPS, you can see your position in relation to waypoints you have marked. Use the waypoint map to easily view, mark and navigate to locations such as brush piles, stumps and docks. It’s also a great tool for finding your way back to the boat ramp.

Check Your Speed on Screen

You can quickly and easily see your boat’s speed on the screen of your STRIKER fishfinder. It’s a great tool to make sure you are trolling at the right speed for the lure you’re using and for a particular fish species. It’s also a good way to tell if you are going the right speed in wake-controlled areas.

Take Your Fishfinder Anywhere

A portable kit is available to protect and carry your STRIKER fishfinder with GPS, so it’s perfect for kayak, canoe or ice fishing. It includes a sealed, rechargeable battery with charger, built-in transducer cable management and storage and suction cup transducer mount and float.

Experience the Clarity of CHIRP

STRIKER 4 fishfinder includes a Garmin CHIRP (77/200 kHz) transducer, which provides a visibly higher level of clarity and detail for fish and structure than traditional 77/200 kHz transducers.

Instead of sending just 1 single frequency, CHIRP sends a continuous sweep of frequencies, ranging from low to high, then interprets them individually upon their return. Since the frequencies provide a wider range of information, CHIRP sonar technology can create crisper fish arches with greater target separation.

You also can upgrade to high-performance Garmin CHIRP technology, which provides crystal-clear sonar images with even more remarkable target separation and resolution from shallow to deeper depths. For better fishing, bottom contours are more visible, even at higher speeds, and signal noise can be suppressed at greater depths to provide a more timely interpretation of what’s below.

Product description

Following in the success of the Striker fish finder series, Garmin is proud to announce the new Striker fish finders with ClearVu technology. These devices are designed to allow you to mark your favorite fishing spot and easily navigate back to it tomorrow, saving you time and money. Striker series fish finders are available in 3.5-, 5- and 7-inch display sizes. Display resolution: 480 x 320 pixels.

• Clear Vu scanning Sonar shows you more of what is in the water around your boat; This high frequency sonar gives near photographic images with detailed representations of objects, structure and fish
• The power of simple offers a keyed interface with dedicated buttons; The device is easy to use and easy to install; Available in 3.5, 5 and 7 inch display sizes; Water rating IPX7
• Waypoint map: Use the way point map to easily view, mark and navigate to locations such as brush piles, stumps and docks; Maximum depth 1,600 feet freshwater, 750 feet saltwater; Current draw at 12 volt: 0.23 Ampere
• Chirp Sonar sends a continuous sweep of frequencies which provides a wider range of information; Chirp Sonar is able to create crisper fish arches with better target separation
• Built in flasher: View your sonar data in the classic flasher format; Ideal for ice fishing or vertical jigging. Display size: 1.9 x 2.9 inches (4.9 x 7.3 centimeter); 3.5 inches diagonal (8.7 centimeter)

User questions & answers

Question:	Does this come with a transducer
Answer:	Yes mine came with a transducer. It came with everything needed to set up and be ready to go as if you never had a fish finder before. Although the two wire clamps to hold your cable for the transducer are fragile, I recommend getting new ones
Question:	Does this unit also give depth readings of the water
Answer:	Yes! Depth, temperature, speed you're moving, time of day etc. this is an awesome unit for the price
Question:	does the power source (12 volt i've read) come with the package, or do i need to purchase that
Answer:	Yes you can and I have done just that. You can get it all here on Amazon. There are plenty info doing just this on the internet. Just assemble these parts. Here is what I have. When done I have it mounted via Scotty #141 Kayak/SUP Transducer Mounting Arm with Gear-Head https://www.amazon.com/gp/product/B0174X6T5A/ref=oh_aui_search_detailpage?ie=UTF8&psc=1 Battery is https://www.amazon.com/gp/product/B006LO9XHA/ref=oh_aui_search_detailpage?ie=UTF8&psc=1 The box it fits in is https://www.amazon.com/gp/product/B011ZB4NLO/ref=oh_aui_search_detailpage?ie=UTF8&psc=1 Switch is https://www.amazon.com/gp/product/B011ZB4NLO/ref=oh_aui_search_detailpage?ie=UTF8&psc=1 Uxcell a12110200ux0689 Waterproof Connector Cable Gland is https://www.amazon.com/gp/product/B00AOBGQ26/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
Question:	Does it has map of Middle East Kuwait
Answer:	yes but its top secret

Product features

STRIKER 4

3.5-inch CHIRP Fishfinder with GPS.

Navigate Easily with Waypoint Map

Since the STRIKER fishfinder series includes high-sensitivity GPS, you can see your position in relation to waypoints you have marked. Use the waypoint map to easily view, mark and navigate to locations such as brush piles, stumps and docks. It’s also a great tool for finding your way back to the boat ramp.

Check Your Speed on Screen

You can quickly and easily see your boat’s speed on the screen of your STRIKER fishfinder. It’s a great tool to make sure you are trolling at the right speed for the lure you’re using and for a particular fish species. It’s also a good way to tell if you are going the right speed in wake-controlled areas.

Take Your Fishfinder Anywhere

A portable kit is available to protect and carry your STRIKER fishfinder with GPS, so it’s perfect for kayak, canoe or ice fishing. It includes a sealed, rechargeable battery with charger, built-in transducer cable management and storage and suction cup transducer mount and float.

Experience the Clarity of CHIRP

STRIKER 4 fishfinder includes a Garmin CHIRP (77/200 kHz) transducer, which provides a visibly higher level of clarity and detail for fish and structure than traditional 77/200 kHz transducers.

Instead of sending just 1 single frequency, CHIRP sends a continuous sweep of frequencies, ranging from low to high, then interprets them individually upon their return. Since the frequencies provide a wider range of information, CHIRP sonar technology can create crisper fish arches with greater target separation.

You also can upgrade to high-performance Garmin CHIRP technology, which provides crystal-clear sonar images with even more remarkable target separation and resolution from shallow to deeper depths. For better fishing, bottom contours are more visible, even at higher speeds, and signal noise can be suppressed at greater depths to provide a more timely interpretation of what’s below.

• Waterproof : The portable fish finder is waterproof in rains. No need to worry the splashes makes the display damaged any more. Even though the portable fish finder dropped into the river or lake, the fish finder would be floating on the water surface. You just need to put the handheld fish finder in open air after fishing to avoid water vapor generated inside display because of the temperature differences.
• Water Depth & Fish Location : You can easily get to know the water depth when the sonar transducer fully in the water. If you attached the sonar transducer to the hull your boat or kayak, you will know the water depth distribution of a specific area when the boat or kayak is moving. It will be easier to find a good position for fishing. Meanwhile, you could also know the approximate fish location and fish size by the portable fish finder display.
• Stable Sonar Transducer : The sonar transducer of the portable fish finder is working stable and reliable both in freshwater and saltwater. It offers a 45° beam angle underwater in 200Khz which supports maximum 328ft/100m water depth detection. There is a 25ft/7.62m extension cable and an anti-fish bite plastic float comes with the sonar transducer. The portable fish finder is USB rechargeable by a built-in lithium battery.
• Data Display : The fish finder displays water depth and temperature on the left top. The measurement unit can be freely changed in FT/M and ℉/℃. Besides water depth and fish location, you can also choose a particular underwater area to watch the size and location of the fishes.
• Ideal for Fishing : LUCKY waterproof fish finder is widely applied in ice fishing, kayak fishing, boat fishing and bank fishing. The portable fish finder can be working for 5~6 hours continuously after fully charged. Once the battery save mode is turned on, it could be working even longer than 10 hours.

User questions & answers

Question:	What is the warranty on this product
Answer:	Hello, we provide one-year warranty for this product. If there are any quality problems with the product, please contact our customer service team directly via Amazon email.Hope this helps.
Question:	So this cant be attached to the bottom of a pontoon?! Based on the description, Thats why we bought this. But after receiving, this is just a bobber
Answer:	Usually, the fish finder could be attached to the hull of the kayak directly, because there usually be a hole on the hull of kayak. However, if you can't attach the transducer to the bottom of your pontoon, please contact our customer service through amazon message, and we will help you out with your problem.
Question:	will this mount under a kayak from walmart
Answer:	Yes, this fish finder is suitable for kayaking fishing, you can fix the sonar transducer to the hull of the kayak or by LUCKY transducer arm mount.
Question:	I know this will pick up fish and bottom topographical image's. Will it show your bait so you know how far down you are
Answer:	Hi,this waterproof fish finder could detect your bait if your bait keep moving and the sensitivity of your fish finder be adjusted to full.

Product features

Advantages

• The display of the portable fishing finder is waterproof against rains or splashes. Even thought it was dropped in the water, the display will not be damaged.

Anti-corrosion Material

• The portable fish finder can be used either in freshwater or saltwater. You just need to dry it in open air after fishing,and it will prolong the life time of this fishing gadgets.

Anti-fish Bite Sonar Transducer

• We choose polymer plastics for the float instead of the foam. The surface of the sonar transducer is much more smooth, and it is difficult for the fish bite.

Ice Fishing

1. Clear the snow and put the sonar transducer on the smooth ice layer. Then the fish distribution under the ice layer could be displayed on the portable fish finder host.
2. There should be no air between the sensor and the ice and no air between ice layer and the underwater either. Otherwise, the portable fish finder will not work properly.
3. Cut a hole through the ice and put the sonar transducer directly in the water and enjoy the ice fishing

Kayak Fishing

1. Fix the sonar transducer to the hull of the kayak or by LUCKY transducer arm mount.
2. Put the sonar sensor submerged completely in the water and you will get useful fishing data on your portable waterproof fish finder.

Boat Fishing

1. Attach the Side-Scan Adapter to the boat hull using the mounting tabs.
2. Break though the hull of a boat. Place the fish finder transducer against the hull bottom 1 inch underwater.
3. The moving speed of kayak should be below 5mph.

Bank Fishing

1. Fixed the removable float on the cable.
2. Cast the fishing sonar transducer into water as far as you can.
3. You can cast the fishing sonar transducer either by your hand or by the fishing rod.

• ◆ Fishes and bottom contour readout: LUCKY fish finder portable detects and displays water depth, approximate fish location, short & tall weeds, sand & rocks on bottom. Fish finder portable design gives you another option to hang it around neck.
• ◆ The kayak fish finder suits for variety fishes fishing environments: It can be used for off shore fishing, kayak fishing, ice fishing, lake fishing, sea fishing and so on. You can also use handheld fish finder on the moving kayak with speed below 5mph.
• ◆Depth readout: The fish finder portable detector range is in a 45°cone underwater. The detection of depth range is from 3ft(1m) to 328ft (100m) below fishing sonar transducer. The water depth can be shown either in feet or meter. The fishing sonar sensor is with 25 ft cable and removable transducer float.
• ◆ Small portable fish finder with powerful functions: 5 modes sensitivity options; battery save mode; backlight mode; fish and fish school alarm. Normally fishing depth finder supports 4-5 hours continuous working with brand new batteries. Open battery save mode can be working even longer.
• ◆ Warranty Policy: We offer 12 months warranty for LUCKY fish finder portable. It will be one of your best fishing kayak accessories. Any questions before or after purchase, please feel free to contact us via Amazon message (response within 24 hours every day online).

User questions & answers

Question:	Please i need a trasceduser cable replacement. How much will it cost me
Answer:	no, you will need a big one. Jack-Hammer would be best.
Question:	It works in salt water
Answer:	I'am not sure about basalt rock but to give you a example it was slow braking 8" concreat but did the job.I have used it on many projects it works very well.
Question:	can you mount the transistor in side the kayak
Answer:	If it is a steel rod, then most likely. This thing will easily break rocks. You will need some kind of driver bit to fit it. If the rod is very long it may be difficult to lift the tool above the rod to get it started.
Question:	Does it work well for ice fishing
Answer:	Some type of cast metal, not plastic.

Product features

Function

• Well understand the water depth and fish location by the portable fish finder.
• The fish finder portable gives you alerts when fish and fish schools passing by.
• 5 modes sensitivity options enable you to use the kayak fish finder in different fishing environments.
• The kayak fish finder can be used in different ways, such as on ice, fixed to kayak, put it into a hole or float it on water surface.
• You can understand the composition of the bottom contour. Sands, rocks and weeks will be shown on the LCD display.

Specification

• 2inch TN/ANTI-UV LCD Display.
• Blue LED Back lighting.
• Measurement Unit: FT/M
• 1.81inch diameter transducer sensor.
• Detect Depth Range: 3ft~328.08ft (0.6m~100m) under sensor.
• Sensor coverage range: 45 degrees beam angle in 200Khz.
• Sensor Operating Temperature: 14°F to 122°F(-10°C-50°C) .
• Cable Length: 25ft (7.62m)
• Powered by: 4 x AAA batteries (not included)

For Kayak Fishing

1. Attach the Side-Scan Adapter to the boat hull using the mounting tabs.
2. Break though the hull of a boat. Place the fishing sonar sensor against the hull bottom 1 inch underwater.
3. The moving speed of kayak should be below 5mph.

For Ice Fishing

1. You should clear the snow on the ice layer. Make sure the surface is smooth enough. Put the LUCKY fish finder portable directly on ice layer to detect fish distribution in purpose of selecting a place to drill a hole.
2. There should be no air between the sensor and the ice and no air between ice layer and the underwater either. Otherwise, the portable fish finder will not work properly.
3. Cut a hole through the ice and put the fishing sonar sensor directly in the water. Enjoy the fishing gear

For Shore Fishing

1. Fixed the removable float on the cable.
2. Cast the fishing sonar transducer into water as far as you can.
3. You can cast the fishing sonar transducer either by your hand or by the fishing rod.

• Lucky New Arrival Fishing Fish Finders: This portable fish finders detects and shows fish location with water depth, short & tall weeds, sand & rocks. The color LCD display of the kayak fish finder is visible under sunshine. Backlight enable the fishing sonar for night fishing.
• Muti Functional Fish Finders: Five assistant settings are available on this portable fish finders. Adjustable sensitivity; battery save mode; backlight mode; fish and fish school alarm and battery indicator.
• Detecting Depth: The portable fish finders works with wired transducer with a 25ft cable wire. The detecting depth range of the fishing sonar is from 3ft(1m) to 328ft (100m) with 45°detecting degree. The depth unit can be switched from “M” to “FT” if long press enter button for 5 seconds.
• Long Working Time Fishing Fish Finder: This portable depth finder uses 4 AAA batteries. Normally this fish finders for kayaks can continue working for 4-5hours with brand new batteries. If you select battery saving mode, the kayak fish finder will keep working more time.
• Wide Applications Portable Depth Finder: This fish finder for kayaks is designed to be omnipotent. You can use this portable depth finder for various fishing occasions like boat fishing, kayak fishing, sea fishing, ice fishing and so on.

User questions & answers

Question:	Is it able to detect the thermocline
Answer:	No, the portable fish finders are unable to detect the thermocline.
Question:	Will it detect a single fish or does it have to be more than one to be detected
Answer:	I will detect a single fish, but it may look like multiple fish as they scroll to the left.
Question:	What is the accuracy of fish By that I mean. Has anyone actually had proof that there were fish down where it said there were
Answer:	It tells me all the time that there's fish around but I don't ever get a bite
Question:	does this detect your lure as its going down
Answer:	Hello, this fish finder detects by reflection of sound waves. If your lure is within the detection range, when the sound wave encounters it, the display screen can indicate the depth of the water layer where it is. Hope this helps.

• 【Fishes and Contour Readout】The fish finder portable detects and displays water depth, approximate fish location, fish size, short & tall weeds, sand & rocks on bottom.
• 【Suitable for Various Fishing Ways】It can be used for off shore fishing, kayak fishing, ice fishing, lake fishing, sea fishing , river fishing, and so on. It will be one of your best fishing accessories.
• 【Depth Readout】 The fish finder portable detector range is in a 45°cone underwater. The detection of depth range is from 3ft(1m) to 328ft (100m) below fishing sonar transducer. The fishing sonar sensor is with 25 ft cable and removable transducer float. Water depth shows by meters/feet.
• 【Powerful Functions】5 modes sensitivity options; battery save mode; backlight mode; fish alarm; unit of measure. Normally fishing depth finder supports 4-5 hours continuous working with brand new batteries. Open battery save mode can be working even longer.
• 【Durable EVA Case】Hard EVA case is handy and comfortable hand carry strap. Enjoy your next trip and adventure together with your important gadget, very organize and spot it within seconds and easy to carry too, your device will perfectly fit inside ad our protective and specialized storage just for your device.

User questions & answers

Question:	Hi, can you mount the transistor in side the kayak
Answer:	I usually fix the transducer on the hull of the kayak (the outside). Because the transducer can only be working when it touches the water.
Question:	is the fish finder waterproof, meaning if it falls into the water will it still work
Answer:	No it's not waterproof.
Question:	Is there a longer cable or extension
Answer:	Not yet
Question:	How long does the battery last
Answer:	According to my experience, you can use it for about 4 hours continuously If you put in brand new batteries

Product features

Features:

1. Sonar beam: 200KHz sonar beam with stable signal, effectively prevent signal disturbance.
2. Fish alarm: Allow you to instantly capture the fish without watching the float for a long time.
3. Selectable sensitivity: Easy to select the information of fish according to your different needs.
4. Powerful functions: Battery save mode, Fish depth scale and fish size distinguish, Parameter setting memory
5. Underwater structure displays: Deliver the information and environment of beneath the surface and help identify fish targets.

Ice Fishing

1. You should clear the snow on the ice layer. Make sure the surface is smooth enough. Put the fish finder portable directly on ice layer to detect fish distribution in purpose of selecting a place to drill a hole.
2. There should be no air between the sensor and the ice and no air between ice layer and the underwater either. Otherwise, the portable fish finder will not work properly.
3. Cut a hole through the ice and put the fishing sonar sensor directly in the water. Enjoy the fishing gear

Kayak Fishing

1. Attach the Side-Scan Adapter to the boat hull using the mounting tabs.
2. Break though the hull of a boat. Place the fishing sonar sensor against the hull bottom 1 inch underwater.
3. The moving speed of kayak should be below 5mph.

River Fishing

1. Place the transducer and float in your hand, and toss underhand.
2. Use a pole to guide the transducer to a desirable position.
3. Add a float kit on the cable to allow the cable to float on top of the water.
4. Neatly wind up the excess cable.

Shore Fishing

1. Fixed the removable float on the cable.
2. Cast the fishing sonar transducer into water as far as you can.
3. You can cast the fishing sonar transducer either by your hand or by the fishing rod.

Attention:

1. It will turn off automatically if the depth display reads "---" continuously for 5 minutes.
2. The transmitter is waterproof, but the receiver (unit with screen) is not waterproof, so please do not submerge or spray the fish finder screen with water.
3. It can not be used to detect bait fish(motionless) or fish that is smaller than 10cm.
4. When use this fish finder on moving boat, please make sure the moving speed is slowly (lower than 5 mph).
5. Extremely cold weather will impact the performance of the product. It is suggested that you keep the unit in temperatures above 0 degrees during operation.
6. Strong waves, suspended matter and muddy water,will affect the performance.

Package Included :

1. Fish Finder Display
2. Sonar Sensor (Transducer) with 25ft cable
3. Removable Transducer Float with Rubber Stopper
4. Transducer Side-Scan Adapter
5. Stainless Bolt and Wing Nut
6. Neck Strap
7. Operation Manual
8. Hard Travel Case

• Shows you what is in the water: Detects and displays water depth, approximate fish location (suits for all sorts of fish), short & tall weeds, sand & rocks on seabed. Suitable for fishing from a kayak, off the dock, and ice fishing. You can use the fish finder on moving kayak with slowly speed below 5mph (make sure the bottom of the transducer is horizontal).
• Easy to Use: Toss the transducer into water and turn on the display unit, it will show you the water depth and approximate fish depth if fish schools passing by. It has 5 user selectable sensitivity; battery save mode; backlight mode ; fish alarm; unit of measure. Setting can be saved when turned off.
• Very portable that you can take it anywhere: It comes with neck strap that allow you to wear it around neck when you are busy on the kayak. And you can easily store the fish finder in your tackle box. The fishfinder is powered by 4 AAA batteries. It lasts 4-5 hours with new batteries in continuous use. It can be used in fresh water as well as salt/sea water.
• Accurate Depth Reading: The fish finder use sonar to detect water depth and fish location. Sonar Frequency is 200 kHZ. Detectable area is 45 degrees beam angle under the sonar transducer. Detectable depth range is from 3ft/1m to 328ft/100m below the sonar transducer.
• Warranty and Brand Support: The Venterior Portable Fish Finder is covered by a 2-year Warranty. Any issue of the fish finder after purchase, please don't hesitate to contact our brand support (warranty card comes with product in package), we will response within 24 hours every day online.

User questions & answers

Question:	Does the display light up at night
Answer:	Hello. Yes, this amplifier will support two subwoofers. You will need to make sure that each subwoofer does not exceed 400 watts peak power.
Question:	Can you use it from the shore
Answer:	Hello. I would recommend purchasing a monoblock amplifier to power your subwoofer. The R4004 is a 4 channel amplifier that would work better for your speakers.
Question:	Will this work fishing in the jetty
Answer:	Dimensions of the R4002 are 10.79" x 10.43" x 2.25".
Question:	Will it work for ice fishing
Answer:	It depends on what ohm speakers you have

Product features

Finding fish is much easier then ever before

For kayak/boat fishing, it is very important to know well about the depth of the water around your boat. The Venterior fish finder use sonar of 200 kHZ to detect and locate depth and bottom contour as well as fish directly below the transducer. The reading shows on display is very easy to read and understand.

25ft cord enables you to use it in different fishing environments

It includes a 25ft cord with round sonar transducer and removable transducer float, which enables you to fish from a kayak, off the dock, or on bridge with the fish finder. If you are fishing off your kayak and the cord is too long for you, you can coil the rest of the cord.

Easy to use

Toss the transducer into water and turn on the display unit, it will show you the water depth and approximate fish depth if fish schools passing by.

ICE FISHING

1. If you would like to check the area for depth or fish before cutting the hole, please clear away snow to expose the ice surface.

2. The ice must be clear, free from air bubbles, voids, cracks, etc.

3. Place a small amount of liquid water on the ice and set the transducer on the water, allowing the unit to freeze to the ice.

4. Cut a hole through the ice and place the transducer directly in the water.

KAYAK FISHING

3 different ways to use the fish finder from a kayak/boat:

1. Toss the transducer and float into the water off the boat side.

2. Attach the side-scan adapter to the boat hull, and attach the transducer to the adapter.

3. Attach the transducer to a handle or a transducer mounting Arm, lower the transducer into the water.

SHORE/PIER FISHING

1. Place the transducer and float in your hand, and toss underhand.

2. Use a pole to guide the transducer to a desirable position.

3. Add a float kit on the cable to allow the cable to float on top of the water.

4. Neatly wind up the excess cable.

FISHING GIFT

If you are looking for some useful fishing gear that can be given as a gift on Valentine’s Day, birthdays, Father’s Day or Mother’s Day, this portable fish finder is one of the best choices. If your family/lover/friend is an avid angler, this makes a great Christmas gift for he/she can go out and use it immediately. They can go fishing off boat in Summer and go ice fishing in Winter with this Venterior portable fish finder.

• Ice Fishing : This portable fish finder model is an ideal choice for ice fishing. The blue housing wrapped up the transducer so that the sonar sensor could better penetrate the ice layer in winter. Meanwhile, the housing design could make the transducer avoid the interference and improved performance up to 30% compared to the other portable fish finders.
• Water Depth Display : The portable fish finder could display many useful data for fishing, such as water depth, fish location, weeds, rocks, sands and so on. You can judge the approximate types of fish and fish schools by the water depth readout of the portable fish finder from your fishing experience.
• Portable & Handheld : The portable fish finder is easy to use and operate. You can either put it in your pocket or hang it around your neck. The fish finder portable supports battery save mode, so that it could make the fish finder working continuously even more than 6 hours in ice fishing, sea fishing and so on. The blue backlight allows display visible in sunlight or in the dark.
• Underwater Detection Range : The fish finder portable detection range is in a 45° beam angle underwater. The detection range of the sonar sensor is 3ft(1m) to 328ft (100m) below the fishing sonar transducer. The water depth could be displayed either in feet or meter. You can freely switch the measurement unit by pressing the "Enter" button of the portable fish finder.
• Wide Applications : The fish finder portable could be applied in various fishing environments, such as ice fishing, sea fishing, bank fishing, lake fishing and so on. The blue housing could be easily removed from the transducer. Moreover, the wired transducer could also be attached to the hull of the boat or kayak directly.

User questions & answers

Question:	Rechargeable or battery
Answer:	This handheld fish finder needs 4 x AAA batteries(Not included in the package).This wired fish finder is not rechargeable.

• 【Fishes and Contour Readout】The fish finder portable detects and displays water depth, approximate fish location, fish size, short & tall weeds, sand & rocks on bottom.
• 【Suitable for Various Fishing Ways】It can be used for off shore fishing, kayak fishing, ice fishing, lake fishing, sea fishing , river fishing, and so on. It will be one of your best fishing accessories.
• 【Depth Readout】 The fish finder portable detector range is in a 45°cone underwater. The detection of depth range is from 3ft(1m) to 328ft (100m) below fishing sonar transducer. The fishing sonar sensor is with 25 ft cable and removable transducer float. Water depth shows by meters/feet.
• 【Powerful Functions】5 modes sensitivity options; battery save mode; backlight mode; fish alarm; unit of measure. Normally fishing depth finder supports 4-5 hours continuous working with brand new batteries. Open battery save mode can be working even longer.
• 【Package Included】1. Fish Finder Display 2. Sonar Sensor (Transducer) with 25ft cable 3. Removable Transducer Float with Rubber Stopper 4.Transducer Side-Scan Adapter 5. Stainless Bolt and Wing Nut 6.Neck Strap 7.Operation Manual.

User questions & answers

Question:	Is this Bluetooth or Wifi
Answer:	Neither, this is wired fish finder. The display in main image can be connected with the transducer part included in the package.
Question:	Does this have to be used on a boat? Or can you use it without a boat
Answer:	I think you could also use this fish finder for fishing off the dock or on the bridge if the depth of the water you are fishing is deeper than 3ft.
Question:	I would like to know can this be used for crabbing
Answer:	Yes, of course you can also used for fishing crab with this fish finder
Question:	Can it works off a Bridge
Answer:	Depends on how tall the bridge is. s long as the height of the bridge is within 22ft and the water depth is deeper than 3ft, the fish finder can works off the bridge. I did use it off a bridge. works great.

Product features

Features:

1. Sonar beam: 200KHz sonar beam with stable signal, effectively prevent signal disturbance.
2. Fish alarm: Allow you to instantly capture the fish without watching the float for a long time.
3. Selectable sensitivity: Easy to select the information of fish according to your different needs.
4. Powerful functions: Battery save mode, Fish depth scale and fish size distinguish, Parameter setting memory
5. Underwater structure displays: Deliver the information and environment of beneath the surface and help identify fish targets.

Ice Fishing

1. You should clear the snow on the ice layer. Make sure the surface is smooth enough. Put the fish finder portable directly on ice layer to detect fish distribution in purpose of selecting a place to drill a hole.
2. There should be no air between the sensor and the ice and no air between ice layer and the underwater either. Otherwise, the portable fish finder will not work properly.
3. Cut a hole through the ice and put the fishing sonar sensor directly in the water. Enjoy the fishing gear

Kayak Fishing

1. Attach the Side-Scan Adapter to the boat hull using the mounting tabs.
2. Break though the hull of a boat. Place the fishing sonar sensor against the hull bottom 1 inch underwater.
3. The moving speed of kayak should be below 5mph.

River Fishing

1. Place the transducer and float in your hand, and toss underhand.
2. Use a pole to guide the transducer to a desirable position.
3. Add a float kit on the cable to allow the cable to float on top of the water.
4. Neatly wind up the excess cable.

Shore Fishing

1. Fixed the removable float on the cable.
2. Cast the fishing sonar transducer into water as far as you can.
3. You can cast the fishing sonar transducer either by your hand or by the fishing rod.

Attention:

1. It will turn off automatically if the depth display reads "---" continuously for 5 minutes.
2. The transmitter is waterproof, but the receiver (unit with screen) is not waterproof, so please do not submerge or spray the fish finder screen with water.
3. It can not be used to detect bait fish(motionless) or fish that is smaller than 10cm.
4. When use this fish finder on moving boat, please make sure the moving speed is slowly (lower than 5 mph).
5. Extremely cold weather will impact the performance of the product. It is suggested that you keep the unit in temperatures above 0 degrees during operation.
6. Strong waves, suspended matter and muddy water,will affect the performance.

Package Included :

1. Fish Finder Display
2. Sonar Sensor (Transducer) with 25ft cable
3. Removable Transducer Float with Rubber Stopper
4. Transducer Side-Scan Adapter
5. Stainless Bolt and Wing Nut
6. Neck Strap
7. Operation Manual

• ★The portable fish finder, with 2.4inch TFT color LCD screen, can detect and display underwater contour, water depth, water temperature and fish size with depth. It has two user modes: WIRELESS/SIMULATION. You can try all functions in simulation mode and go fishing in wireless mode.
• ★The wireless sonar transducer, with fish attractive lamp, makes it easier to detect fishes. It has a transparent replacement cover, so you can see where the sensor is even in the dark.
• ★The wireless fish finder supports 196FT(60m) wireless operating range(There is an antenna on the left top of the hand held, please pull it out), 147FT(45m) depth detection. You can go fishing in different ways with it, such as ice fishing, river fishing, sea fishing, fishing off the shore, kayak fishing or fishing in the night.
• ★Various features settings: detect sensitivity, screen brightness, depth range, zoom, depth alarm, fish alarm, fish icon, units alter and language choose.
• ★Both of the wireless fish finder and the sonar are rechargeable. Come with a USB cable for charging. The hand held can last 4 hours with full charge and the sonar sensor can last 10 hours with full charge.

User questions & answers

Question:	Are there assesories to buy with this product
Answer:	yes, the package contain all assesories and the display device.
Question:	Can it be used in saltwater
Answer:	Dear Amazon customer, yes, it can.
Question:	Can this be slow trolled from a boat
Answer:	Depends on the speed. Very slow yes, less than 3 mph otherwise it just drags and from experience affects accuracy.
Question:	How is the screen in bright sunlight
Answer:	I would love to help but we haven't had any weather good enough to say for sure, (I haven't had it on the water yet). From what I have seen it looks really good.

Product features

Wireless Sonar Sensor

The wireless sonar ball of the wireless fish finder comes with 2 fish attractive lamps. It can help you find the fishes more easily.

The detect angle of the sonar transducer is 90, and the detect depth is from 0.7m(2.3ft) to 45m(147ft).

The wireless operating distance of the depth sounder can reach to 60m(196ft).

Warm tip: please pull the antenna out when you detect fishes in the water.

Portable Fish Finder with Clear Screen

Give you the information including water depth, water temperature, fish size, fish depth, underwater countour and you can easily read it on the screen.

Portable and handheld. You can easily take it to go fishing.

Warm tip: the sonar sensor is waterproof, but the hand held Lucky fish finder is not. Please do not submerge or spray the wireless fish finder screen housing with water or use chemical to clean.

Shore Fishing

Kayak Fishing

Sea Fishing

Ice Fishing

• Waterproof : The sonar fish finder is waterproof in rains. No need to worry the splashes makes the display damaged any more. Even though the sonar fish finder dropped into the river or lake, the fish finder portable would be floating on the water surface. You just need to put the wireless fish finder in open air after fishing to avoid water vapor generated inside display because of temperature differences.
• Wireless & Castable : The sonar transducer supports max 328ft wireless operation and max 147ft water depth detection. The sonar ball is lightweight and compact and you don’t need long heavy cable anymore. Moreover, there is a small hole on the sonar transducer so that you can tether with your fishing line and cast it onto water easily.
• Water Depth & Data Display : The sonar fish finder displays water depth, fish approximate location, fish size (small,middle,big), water temperature, bottom contour and so on. Besides that, you can also choose a particular underwater area on the display to learn each data more accurately. The measurement unit can be freely switched in FT/M and ℉/℃.
• Sonar Transducer with Attractive Lamp : The sonar transducer works with 125Khz in a 90 degrees beam angle. The wireless fish finder will alerts when the sonar ball detects fish or fish schools. Even more, you will get alarm when it detects shallows. You can put the replacement transparent cap on the sonar ball which will be glowing in the dark, so you will easy to know where the sonar ball is when night fishing.
• Ideal for Fishing : LUCKY sonar fish finder is widely applied in ice fishing, kayak fishing, boat fishing and bank fishing. The wireless fish finder can be working for 5~6 hours continuously after fully charged. Once the battery save mode is turned on, and it could be working even longer than 10 hours.

User questions & answers

Question:	is there a battery in the hand unit
Answer:	no rubber mounts (80mm pure wings 2)
Question:	Can it be used on a boat in motion
Answer:	There are 3 pin variants and 4 pin PWM variants. Also, standard and high speed versions. I recommend visiting the manufacturers website to help determine which version fits your needs.
Question:	Can this be used for saltwater fishing from small boat
Answer:	use a buck converter
Question:	Could you drop this in an ice fishing hole
Answer:	yes

Product features

Advantages

• The display of the sonar fishing finder is waterproof against rains or splashes. Even thought it was dropped in the water, the display will not be damaged.

Anti-corrosion Material

• The sonar fish finder can be used either in freshwater or saltwater. You just need to dry it in open air after fishing, and it will prolong the life time of this fishing gadget.

Advanced Sonar Ball

• The sonar transducer ball is USB charging in compact design. When it is working in the water, the glowing bobber will attract more fish and fish schools.

Ice Fishing

Kayak Fishing

Boat Fishing

Bank Fishing

Product description

This is a wireless, castable and rechargeable fish finder with clear color screen for avid fisherman. It is suitable for trolling from a kayak or boat, casting from the shore or using for ice fishing. You will be able to learn the depth, temperature and bottom contour of water that don't have topographical maps and find where the fish are in the them.

Feature:

1. The handhold units and the sonar sensor both are rechargeable

2. Easy to use: tether the sensor with fishing line (not included) and cast it onto water.

3. 20-level Sensitivity (high detection accuracy)

4. 10-level backlight brightness.

5. Two Background Mode: White and Black

Specification:

1. Display

Display Size: 2.6inches

2. Sonar & Radio

Depth Range: 2.6-131FT/0.8-40M

Sonar Frequency: 125KHZ

Sonar Beam Angle: 105 degree

Radio Frequency: 433MHz

Operational Temperature: 14°F to 122°F(-10°C to 50°C)

3. Power Supply:

Display Unit: Built in Polymer battery 3.7V

Sensor: Built in Polymer battery 3.7V

Battery Life of Display:

If backlight set to be 10%, the battery life will last about 6 hours ( fully charged );

If backlight set to be %100, the battery life will only last about 3 hours( fully charged ).

Battery Life of Sensor:6-8 hours ( fully charged ).

Attention/Tips:

1. The cover/top of the sensor should be removed when charging, and should NOT be removed when used.

2. Its reading might be interfered by other high power sonar fish finder close to your fish finder.

3. The wireless fish finders are on the same frequency. If two fish finder are close, the display unit might read the other one's sonar.

4. Please make sure battery is fully charged before use.

5. Please prevent the sensor from crashing into rocks or other hard items.

6. Strong waves, suspended matter and muddy water, might affect its performance.

• Wireless and castable: No more long & heavy cable for transducer. Clear Color Screen: it comes with clear color TFT LCD display (2 screen background colors selectable - black and white), which enables you to read the screen in bright sunlight or at night. It applies to lake, river, sea and other fishing environment. Suitable for trolling from a kayak or boat, casting from the shore or using for ice fishing.
• It detects and displays water depth, water temperature, fish size (small/medium/big), fish depth, and bottom contour. It has Work and Simulation Mode. Measure units of depth and temperature can be converted. Sonar Beam Angle: 105 degree. Depth Range: 2.6-131FT/0.8-40M. Wireless Distance Range: 262FT/80M.
• No need to drill hole in your boat hull to install the sensor any more. Two small holes on the wireless sensor allow you to tether with your fishing line and cast it onto water as far as you want.
• Note: 1. Press and hold 3 seconds to turn on the display. 2. The sensor will turn on automatically when cast into water. 3. When the sensor is off, its battery Indicator on the display is incorerct. Red indicator light on the sensor will turn off when it is fully charged. If you would like to check the sensor's battery status from the display, please put the sensor in water. It will turn on when it floats on water. The sensor's battery Indicator on the display will then display correctly.
• Warranty and Brand Support: The Venterior Portable Fish Finder is covered by a 2-year Warranty. Any issue of the fish finder after purchase, please don't hesitate to contact our brand support (warranty card comes with product in package), we will response within 24 hours every day online.

User questions & answers

Question:	Is the handheld device waterproof
Answer:	No, it is not waterproof. But we offer waterproof resistant bag for the handheld device. You can refer to the bundle with this item or search "B08P513DW2" on Amazon.
Question:	Can i use it ice fishing
Answer:	Yes. It can be used for ice fishing.
Question:	Does this really have 105 degree beam angle
Answer:	yes it is also very accurate
Question:	Just used this for first time. Ran a 6 inch swimbait about 4-5 ft under it. Nothing. Anyone have any thoughts
Answer:	It will not detect bait and show it as fish on the screen. The sonar fish finder will only detect swimming fish. Besides that, please make sure your turn on the fish symbols feature of the fish finder. If you turn off the fish symbols feature, it will only show water depth and will not display fish on the screen. Please rest assured, all Venterior fish finder is eligible for a 2-year warranty. If you have any questions or need any warranty or technical support, please feel free to contact our brand support on the warranty card. Sincerely, Venterior

Product description

At Hummingbird, innovation is the core of everything we do. The new HELIX Series is no exception-delivering our full array of technologies, including the intuitive REFLEX interface, precise Broadband CHIRP, incredible Imaging SONAR and the mapmaking power of Auto Chart Live. Fueled by DNA that is unmistakably Hummingbird, the HELIX Series also features a jaw-dropping industrial design. From top to bottom, it's plain to see that finding fish runs in this family. HELIX 5 CHIRP GPS G2 HELIX 5 Series 410210-1 ​The HELIX 5 CHIRP GPS G2 with our new user interface and operating system, features ​a brilliant 800H x 480V, 5" 256 color display with backlight. CHIRP Dual Beam PLUS sonar with 4000 watts PTP power output, Precision Internal GPS Chart plotting with built-in Anima cartography with a micro SD card slot for optional maps or for saving waypoints. Maximize your angling experience with the Hummingbird HELIX 5 CHIRP GPS G2 fish finder system. ​CHIRP Frequencies (Out of Box Transducer)83 kHz:  75-95 kHz200 kHz:  175-225 kHzMaximum Depth:  1500 feetCHIRP Frequencies (Optional Purchase Transducer)Low: 28-75 kHzMed: 75-155 kHzHigh: 130-250 kHz83/200: 75-155/130-25050/200: 28-75/130-250Maximum Depth:  2500 feet

• 5-Inch Color WVGA Display
• CHIRP Dual Beam PLUS Sonar. Power Output RMS : 500 Watts. Power Draw : 615 mA
• Precision Internal GPS Chart plotting with built-in Anima cartography
• Micro SD card slot for optional maps or for saving waypoints
• Target Separation - 2.5 Inches

User questions & answers

Question:	Does this come with a screen cover
Answer:	No it doesn't come with a screen cover.
Question:	This shows that smart strike is included with this unit. Where do I find that option
Answer:	Go to the hummingbird web site or contact the help site by phone
Question:	what is a SD card? where do you get them? and why do i want one
Answer:	SD card is the same card you used in camera a few years back. they store information and slide into a slot on many things like computers and fish finders. they are about 3/4 inches by 1 inch in size and costs about $10.
Question:	How long is the transducer cable? I want to put this on my 20 ft pontoon boat
Answer:	I don't know the specific length, you would need to check the specifications or with the manufacturer. I did install it on my 21' pontoon and it was just long enough to reach the console mounted unit.

Product features

Humminbird HELIX 5 G2 Series Fish Finders

There’s no such thing as 'too early' or 'too far.' High expectations go with the territory. The HELIX 5 Series answers the call with an uncompromising widescreen color display. Available on select models, Humminbird CHIRP Digital Sonar and Imaging Sonar reveal the lake bottom, while GPS mapping, AutoChart Live and Humminbird Basemap show you the way.

Feature for feature, it has what it takes to win the day. Do you? No doubt.

Includes transducer and mounting hardware, power cable and gimbal mounting bracket.

2D Sonar

If your goal is to locate and see fish more clearly, start here. Humminbird’s 2D sonar offerings are far from two-dimensional. Whether you’re fishing freshwater lakes, coastal waters or the ice, you’ll find the right solution for your environment and prey.

SwitchFire

SwitchFire lets you control the way your returns appear. With two display modes—Max Mode and Clear Mode—you can choose how much detail, including fish, structure and thermoclines, you want to see or un-see.

Dual Beam

With a wide beam for more search area or a narrow beam for more precision, DualBeam shows you fish and the bottom. DualBeam Plus lets you combine the two beams for even more detail.

Digital CHIRP

CHIRP stands for 'Compressed High Intensity Radar Pulse.' That’s a fancy way of saying it can show you fish that other forms of 2D sonar can’t. How’s that? CHIRP scans the water for fish similar to the way the seek function on your truck’s radio scans the airwaves for FM stations. By covering a wide range of frequencies, CHIRP produces more accurate, more detailed returns of fish, structure and the bottom.

Imaging - It's all in the details

Amazing Humminbird Imaging sonar shoots high-frequency beams below the surface to reveal structure, cover and contours with crystal clarity.

Side Imaging - Nowhere to Hide

Gain an unprecedented, side-to-side perspective on the world below the surface with Side Imaging. In an instant, the ultra-thin beam scans the area to the left and right of your boat location. The return image for each slice is then added to the images taken immediately before and after to build an incredible view of the lake bottom. (image displays MEGA Side Imaging)

Down Imaging - Look Out Below

Get a fish-eye’s view of what’s happening below your boat with Down Imaging. These incredible images are created with high-frequency sound waves emitted in ultra-thin slices. The sonar returns from these waves produce a 'portrait.' As you patrol the water, you’ll watch timber, brush, bridge pilings, rocks and any other structure pop with stunning detail. (image displays MEGA Down Imaging)

Built-In Basemap - Ready to fish, right out of the box

We’ve enhanced our standard Basemap to deliver more detail and a superior angling experience. The Humminbird Basemap is built into all SOLIX Series and GPS-equipped HELIX Series G2/G2N models. Based on freshwater data from LakeMaster and NOAA, the most-trusted saltwater source, these accurate maps provide you with a clear view of underwater terrain. Identify buoys, daymarkers, hazards, marinas and countless other navigation aids and points of interest with our comprehensive icon system. You’ll also see contours, depth markings and, for coastal areas, spot soundings. On the water, confidence is key. And the Humminbird Basemap delivers.

Autochart Live - Create your map-sterpiece (On select models)

Build richly detailed maps of your favorite fishing spots in real time with Humminbird AutoChart Live, available on the SOLIX Series and all GPS-equipped HELIX Series models. Map the water as you drive the boat, with eight hours of built-in recording time. Once your map is live, view it with vegetation, bottom hardness and depth contours to locate the best fish-holding areas. Also, use it with i-Pilot Link Follow and other patented Humminbird LakeMaster features. The future of digital charting has arrived. Better get on board.

Navigation - Built-In GPS

Get unparalleled GPS technology out of the box. Many Humminbird fishfinders have our powerful Precision GPS/WAAS receiver built right in and provides fast position fixes accurate within 2.5 meters. For those models without it, there are several options: Add the Humminbird Precision GPS/WAAS receiver for permanent GPS capability on your boat. Use Humminbird’s adapter and the NMEA output on your own handheld GPS unit, or use Humminbird’s InterLink to allow two fishfinders to access one GPS receiver.