14 best 10 inch car subwoofers

• Subwoofer and Enclosure Features: Rockville RV10.1D Single 10” Bass Enclosure System With matching Mono Block Amplifier. 500 Watts Peak Power / 175 Watts RMS CEA-2031 Rating.
• Single 10” Bass Enclosure System with matching Mono Block Amplifier. Quasi Transmission Line Cabinet Design. Bonded, Stapled and Braced 3/5" MDF Cabinet. Computer Designed, Under-Side Bass Reflex, Aero-Port System.
• Angled at 15% for near perfect in vehicle bass alignment.
• Exterior: Logo embroidered high quality aviation grade tweed carpet. Mono, gold-plated push style, speaker terminal. High-Power, High-Efficiency 10" Subwoofer. Injection Molded, Talc Filled, Brushed Polypropylene Cone.
• High Excursion Butyl Rubber Surround. 3-D Molded Dust Cap. Linear Progressive Spider System. 4 Layer, High Power, Aluminum Voice Coil. Bumped and Vented Magnet Motor Structure. RMS Power: 175 Watts CEA-2031 Rating.
• Amplifier Features:.1200 Watts Peak Power. Power Output: 200 Watts RMS CEA-2006 Power @ 4-ohm and 97dBA (Reference: 1Watt into 4 ohms).
• Frequency Response: 15Hz - 20KHz (-3dB). RMS Power: 400 Watts @ 2 ohms. 4 Ohm Mono-Block Class A/B. High Speed MosFET Power Supply with 50 Volt Rail. BiPolar Audio Transistor Output Section. RCA Line Input. RCA Line Output - Full Range.

User questions & answers

Question:	can i use the amp with 2 Dual 12 inch speakers
Answer:	Yes you can. Just ensure that the amp is mounted where it can get some flow of air
Question:	Will it work with a 2002 Toyota Highlander with stock stereo
Answer:	Of course any system can work with a stock stereo just make just you know how to install or get a professional
Question:	Can it fit on a Dodge Challenger
Answer:	Measure
Question:	I plugged and wired everything up correctly and it doesn’t work!!! Can someone please help me
Answer:	did you test it before you put everything back in? after you wire everything you should just hook the speakers up and test them to make sure you're good... if you aren't getting any power i would check your wiring and make sure the ground is good.. and everything is up to par.. if your stereo doesn't have power either then you should make sure it's connected properly to the harness.. Make sure your wires are color matched properly.. make sure you have the right wiring harness for your car... ask the question again with more details if you haven't already fixed it.... installed these and they work beautifully

Product features

Rockville RV10.1D 500w 10" Loaded Car Subwoofer Enclosure+Mono Amplifier+Amp Kit

Product description

Kicker 43C104 Comp 10" 300 Watt SVC 4-ohm Car Audio Subwoofer Woofer Sub C104

• 10-INCH SUBWOOFER: One Kicker Comp 10 Inch Car Audio Subwoofer for serious bass power
• 300 WATTS MAX POWER: MAX Power Handling: 300 Watts; RMS Power Handling: 150 Watts
• SINGLE VOICE COIL: Single voice coil 4 ohm impedance, 86.2 dB sensitivity, and 30 - 500 Hz frequency response; High temp coil wire and strong steel basket with coil cooling perimeter venting
• RIGID INJECTION MOLDED CONE: Features super rigid, injection molded cone with 360 degree back bracing; Ribbed and double stitching on surround for strength at high excursion
• SPECIFICATIONS: Mounting depth: 5.06 inches; 45 ounce magnet structure; Vented pole piece for heat dissipation; Durable spiraled tinsel leads; Spring loaded terminals; Weight: 9 pounds; Manufacturer warranty: 1-year warranty

User questions & answers

Question:	I want to Iso-seal these subs. Will the cones on these subs handle that kind of set up
Answer:	Yes, they will work either way. I have them in a sealed enclosure in my sons car.
Question:	Is a 1.0 cubic feet sealed box for under the rear seats be ok for 2 of these
Answer:	No, you need to build a larger box, than one cubic foot
Question:	would it sound good on a 1000 watt sony xplod
Answer:	I believe so. I have a 400watt Blaupunkt bridged and it sounds great. It is in the back of a Jeep Wrangler unlimited
Question:	What's the mounting depth
Answer:	According to Crutchfield, the top mount depth is 5". Bottom mount N/A, I guess due to the outside frame.

Product description

We are an authorized Rockford Fossae dealer! This Pair of **ROCKFORD FOSGATE R2D2 10** 1000 Watt 10" 2 Ohm Prime Series DVC Subwoofers deliver optimum Rockford Fossae sound quality. Each R2D2 10 subwoofer features a Mica injected polypropylene cone, a Stamp Cast basket with spider venting, 12 gauge compression terminals, anodized aluminum voice coil former, PVC trim ring, a linear spider with 16 gauge tinsel leads, and a Dual Voice Coil that provides greater installation flexibility. Let these two ROCKFORD FOSGATE R2D2 10 1000 Watt 10" 2 Ohm Prime Series DVC Subwoofers supply your vehicle with thumping bass! Read the Owner's Manual [here][1] Read the Specifications [here][2] [1]: rockfordfosgate /reach/library/2011/5_Subwoofers/1230_56566_01_PrimeR2Sub MAN. pdf [2]: rockfordfosgate /reach/library/2011/5_Subwoofers/RFPB_R2D2 10 Strive. pdf @[video](p1 dgCyvOZs)

• NEW Pair **ROCKFORD FOSGATE R2D2 10** 1000 Watt 10" 2 Ohm Prime Series DVC Subwoofers
• Max power: 500 watts for each Sub (1000 watts for the pair)
• Rams power: 250 watts for each Sub (500 watts for the pair)
• Quantity: 2 subwoofers total
• Size: 10"

User questions & answers

Question:	Does rockford fosgate make grilles to fit the r2d
Answer:	I'm not sure. Most speaker grills are to shallow, the speaker will hit it.
Question:	How would I wire these subs for a 2000 watt peak Rockville amp db
Answer:	Get 2000 watt speakers
Question:	Would this work for rockford 10" subs that are max 500 watt and ram 250 watt
Answer:	Yes they will .I would recommend purchasing the Rockford fosgate prime 500 watt 1 channel Amp and wire both subs in random to 1 ohm each , I have the same setup in my Silverado and it really hits hard actually gets your hair on your arms to vibrating.
Question:	Mounting depth
Answer:	little over 5"
Question:	Could I use this speaker to replace an 800 watt 10” subwoofer
Answer:	Most likely... they can take a lot of watts...

Product description

The Skar Audio SDR-10 D4 10" dual 4-ohm subwoofer was engineered to dish out reliable, hard hitting, and low spectrum sound. Featuring a high flux ferrite motor, this woofer will provide extreme power handling for extended periods of time. The SDR series will quickly become a customer favorite, as it's perfect for people just entering the world of car audio all the way up to seasoned pros. The SDR-10 dual 4-ohm 10-inch car subwoofer features a 2.5” high temperature 4-layer high temperature copper voice coil that is attached to our Skar Audio signature red spider. The surround on the SDR series is a high roll foam surround which allows the woofer to produce riveting low end bass response. The SDR series has a max power rating of 1,200 watts and a RMS power rating of 600 watts. Sensitivity (Spl): 82.5 dB, Xmax: 13.5mm one-way, Fs: 39 Hz, Frequency Response: 28 Hz- 300 Hz, Mounting Depth: 6.08".

• 10-Inch Dual 4-ohm Car Subwoofer
• Peak Power: 1,200 Watts | RMS Power: 600 watts
• 2.5" 4-Layer High Temperature Copper voice Coil
• High Roll Foam Surround and Competition Grade Pressed Paper Cone
• Frequency Response Range: 28 Hz - 300 Hz | Sensitivity: 82.5 dB
• High Flux Ferrite Motor | Advanced Air Flow Cooling Design

User questions & answers

Question:	Is this subwoofer better, worst, or the same compared to the rockford p
Answer:	I have 2 PCs hooked up to it abd it works fine. Though i did have a hdmi cable that did not work well with it.
Question:	What would hit harder this or 2 of the skar ix-12 d
Answer:	In order to use the hotkey function you will need to press scroll lock on the pc you wish to switch towards, not on the PC the device is currently working on
Question:	Will these fit under a 2019 Ford F-250 seat
Answer:	yes, but dont count on hotkey functionality
Question:	Whats the mountung depth
Answer:	I connected my HP Laserjet M176n with it to my windows 7 company laptop and my windows 10 Desktop PC. the hot key worked from the first second on both computer without any problem, maybe its because I use German keyboard setting on both devices? never had a problem with it, apart from that I placed the switch in front of my keyboard on the desk so I could as well just press the button on the switch itself. hope I was able to help

Product features

Technical Specifications

• Dual 4 Ohm Voice Coil Configuration
• Peak Power: 1200 Watts
• RMS Power: 600 Watts
• Competition Grade Pressed Paper Cone
• 2.5" High Temperature Copper Voice Coil
• Frequency Response: 28 Hz - 300 Hz
• Sensitivity: 82.5 dB
• Xmax: 13.5 mm
• Mounting Depth: 6.08"

Product description

Rockville® has developed and perfected a smart, integrated solution for

adding bass to any vehicle’s audio system. The Rockville slim powered subwoofer

combine subwoofers with matching enclosures and amplifiers for optimal bass

performance.



Utilizing a slim but heavy-duty subwoofer, durable enclosure and mono block

amplifier designed and engineered to work as a complete system resulting in

intense bass response. Featuring a quick-connect Molex high level input with

Smart Turn-On Circuitry, the unit easily integrates in to any OEM system with

minimal of wiring. Power, signal and remote turn-on are achieved via molded

angled terminals for easy access allowing for simple set-up or removal.



The Rockville unit comes standard with a remote bass control, adjustable

low-pass crossover, variable +12dB bass boost, and 150mv to 5 Volt gain control.

It also features high- and low-level inputs for integration with nearly any

factory or aftermarket head unit.



Slim-profile, these loaded enclosures are perfect for car trunks and for behind

or under pickup-truck seats that hug the back of the cab. Available in three

subwoofer sizes these units will fit in any tight area. The units are the

smallest sub boxes designed by Rockville, but don’t let their small size fool

you, they are ready to explode with high power - super intense bass and

extraordinary SPL levels. Rockville has produced a true high-performance

completely integrate active/amplified woofer system – in a compact footprint.



By taking all the ground-breaking technology from the Rockville shallow-mount T3

subwoofers producing real, head-pounding bass, combined with a tough Rockville

carpeted MDF box enclosure and Rockville class leading mono block amplifier

these diminutive enclosure are perfect for placement anywhere in any vehicle. So

save space in your trunk or hatch with the Rockville all-in-one drop-in bass

solution and still have plenty of hauling space.

• Rockville RWS10CA Slim 1000 Watt 10" Amplified Powered Car Subwoofer Enclosure. 1000 Watts Peak power output.
• 300 Watts RMS CEA rated. 10" Super Slim Subwoofer. Ultra Stiff Composite Pulp Cone with Kevlar Reinforcement.
• 3D Molded Acrylic Dust Cap. Expanded & Rolled Steal Basket. High Density Laminated Foam Surround.
• High Power Strontium Magnet with Ultra Saturated High BL Motor Structure. Vented Core Magnet Motor Structure.
• 2" High Temperature Aluminum Voice Coil. 8mm Washer & Yoke Plates. 13.6mm Peak-to-Peak X-Max. 60oz. Magnet Motor Structure.
• Super Slim Sealed MDF Enclosure Design. Aviation Grade Black Tweet Carpet with Embroidered Logo.
• Black Texture Synthetic Leather Front Panel. Impedance: 4-ohms. Frequency response: 43Hz-500Hz. SPL @ 1w/1m: 93dB.

User questions & answers

Question:	I also have an f250 crew cab (06). Do you have to remove the carpet from behind the seat to install this set up? Thank you
Answer:	Won't work! Ripped my carpet and the seat wouldn't fold back upright. Best bet is to remove the storage platform under the bench seat for proper placement.
Question:	I recently installed this subwoofer and am getting very little output unless the gain is up to 90 percent. Did i install something incorrectly
Answer:	You gotta hook up both left and right inputs
Question:	can you hook another speaker to it
Answer:	Negative
Question:	How can i hook another speaker to this one? do i need two amps or is there a way attach another speaker to it? thanks i love the one so far in my truc
Answer:	Drill small hole in box. Run speaker wire through. Seal small hole. The amp on this speaker rocks

Product features

Rockville RWS10CA Slim 1000 Watt 10" Amplified Powered Car Subwoofer Enclosure

Rockville has developed and perfected a smart, integrated solution for adding bass to any vehicle’s audio system. The Rockville slim powered subwoofer combine subwoofers with matching enclosures and amplifiers for optimal bass performance.

Utilizing a slim but heavy-duty subwoofer, durable enclosure and mono block amplifier designed and engineered to work as a complete system resulting in intense bass response. Featuring a quick-connect Molex high level input with Smart Turn-On Circuitry, the unit easily integrates in to any OEM system with minimal of wiring. Power, signal and remote turn-on are achieved via molded angled terminals for easy access allowing for simple set-up or removal.

The Rockville unit comes standard with a remote bass control, adjustable low-pass crossover, variable +12dB bass boost, and 150mv to 5 Volt gain control. It also features high- and low-level inputs for integration with nearly any factory or aftermarket head unit.

Slim-profile, these loaded enclosures are perfect for car trunks and for behind or under pickup-truck seats that hug the back of the cab. Available in three subwoofer sizes these units will fit in any tight area. The units are the smallest sub boxes designed by Rockville, but don’t let their small size fool you, they are ready to explode with high power - super intense bass and extraordinary SPL levels. Rockville has produced a true high-performance completely integrate active/amplified woofer system – in a compact footprint.

By taking all the ground-breaking technology from the Rockville shallow-mount T3 subwoofers producing real, head-pounding bass, combined with a tough Rockville carpeted MDF box enclosure and Rockville class leading mono block amplifier these diminutive enclosure are perfect for placement anywhere in any vehicle. So save space in your trunk or hatch with the Rockville all-in-one drop-in bass solution and still have plenty of hauling space.

Features:

Product description

The Skar Audio EVL-10 D4 10" dual 4-ohm subwoofer redefines the conception of low-end sound reproduction. The engineering that went into developing the EVL series is simply amazing, and it shows in the sound quality and performance that this subwoofer demonstrates. The EVL Series can deliver incredibly accurate and powerful bass, due to a variety of advanced design features that make this subwoofer unique and in a class of its own. Conservatively rated at 2,000 watts peak power, the EVL-10 D4 features a massive high flux, double stack ferrite motor structure - which delivers the driving force behind the tremoring lows this subwoofer can produce. Combine the motor with the black coated 3" high temperature voice coil of this driver, as well as the advanced air flow cooling design of the basket, and it quickly becomes evident why this woofer is capable of being played at the highest levels of output for hours on end. Furthermore, the high roll foam surround incorporated into the design of this subwoofer is one of the reasons it can produce those ultra-low-end frequencies with such responsiveness. The suspension design of this subwoofer features the EVL's signature red, single damper, two-layer spider - which connects to the coil former with premium stitched lead wires. All these incredible features make this EVL subwoofer the unequivocal choice when looking for a high-quality car subwoofer. Dual 4-ohm voice coil impedance, Peak Power: 2,000 Watts, RMS Power: 1,000 Watts, Frequency Response: 28Hz - 300 Hz, Sensitivity: 81.9 dB Fs: 45 Hz, Xmax: 23.5mm (one-way). Subwoofer Mounting Depth: 7.125", Subwoofer Cut-Out Diameter: 9.375".

• Peak Power: 2,000 Watts | RMS Power: 1,000 Watts
• 3" High Temperature Dual 4 Ohm Voice Coil with Black Coating
• Competition Grade Paper Cone & High Roll Foam Surround
• Premium Suspension Featuring the EVL Series Signature Red Two Layer Spider
• Deep, Low, Extremely Responsive Bass | Sensitivity: 81.9 dB
• Frequency Response Range: 28 Hz - 300 Hz | Xmax: 23.5 mm (one-way)

User questions & answers

Question:	What amp for a single evl
Answer:	A skar rp.1500 watt amp would be perfect.factor in box rise and etc and you wont get the full 1500 wats you will get like 700 to 800 watts witch it can hadle all day with no problem
Question:	Can a 4,500 watt mono block power a pair of 10” evl’s
Answer:	If you run dual 4ohm subs bridged together, subs will have 1ohm resistance. As long as your 4500 mono can run 1ohm output, you should be good to go. These subs slam!
Question:	Would 2 of the skar audio evl series 10in 4ohm fit properly in a premade jeeppro box that is made for 2 10s
Answer:	Go on soars website for the dimension of the sub to see if it will properly fit and be of appropriate size for the subs themselves
Question:	I just got got a pair of these with a 2,000 wat amp but was wondering if it would be better if I got a 4,000 amp instead since they 2,000 max each
Answer:	Match the RMS wattage on your amp to your subwoofer the max is not as important as RMS. Also try to stay within 85% of RMS wattage. So if it's a 1000 watt rms sub you can get away with 1,150 watts or 850 watts rms on your amp. Any lower won't give you the boom you want any higher you risk the coils getting burned (ruined or blown out subs are the result). Hope this helps.

Product features

Product Specifications

• Dual 4 Ohm Voice Coil Configuration
• Peak Power: 2000 Watts
• RMS Power: 1000 Watts
• Competition Grade Pressed Paper Cone
• 3" High Temperature CCAW Voice Coil
• Frequency Response: 28 Hz - 300 Hz
• Sensitivity: 81.9 dB
• Xmax: 23.5 mm
• Mounting Depth: 7.125"

Product description

The CompVR 10 Inch Subwoofer is a 2 ohm dual voice coil design, built for easy wiring. The CompVR gets earth shattering bass to you by engineering a stable base and a cool, powerful motor. Powerful magnets and dual high temp voice coils move a stiff polypropylene cone, while perimeter venting keeps the air moving around the motor. You get strong bass that keeps on bumping day in – day out. The CompVR 10 Inch Subwoofer works best with a sealed or ported enclosure and 400 watts of recommended power.

• 10-INCH SUBWOOFER: One Kicker CompVR round 10 Inch Car Audio Subwoofer for serious bass power
• 700 WATTS MAX POWER: MAX Power Handling: 700 Watts; RMS Power Handling: 350 Watts
• DUAL VOICE COIL: Dual voice coil 2ohm impedance, 83.6 dB sensitivity, 30 - 500 Hz frequency response; High temp coil wire and strong steel basket with coil cooling perimeter venting
• POLYPROPYLENE CONE: Features super rigid, injection molded polypropylene cone with 360 degree back bracing; Ribbed and double stitching on surround for strength at high excursion
• SPECIFICATIONS: Mounting Depth: 5.5"; Mounting Diameter: 9 3/16"; Min Sealed Box Volume: .8 cu. ft.; Max Sealed Box Volume: 3 cu. ft.; Min Vented Box Volume: 1.25 cu. ft.; Max Vented Box Volume: 1.75 cu. ft.; Manufacturer warranty: 1-year warranty

User questions & answers

Question:	Does it come with the screws
Answer:	Yes comes with hardware very nice subwoofers
Question:	Will it fit in kicker ported slim box
Answer:	Hard to say read the tech sheets for both sub and box
Question:	Mounting depth
Answer:	Mounting depth is 5-1/2 inches or roughly 14 cm.
Question:	Where can I find the Specs for this speaker
Answer:	Kickers web sight

Product description

Planet Audio AC10D Car Subwoofer - 1500 Watts Maximum Power, 10 Inch, Dual 4 Ohm Voice Coil, Easy Mounting, Sold Individually

• CONE: Made from Polypropylene, the AC10D 10-inch car subwoofer provides a resilient and durable material that can offer great sound with the advantage of long-lasting subwoofers
• SURROUND: Foam is very flexible, providing the subwoofer with higher efficiency. This also translates to better excursion. (How far the cone of a speaker linearly travels from its resting position)
• VOICE COIL: Our voice coils are able to withstand high temperatures yet maintain its strength and fatigue properties. making our voice coils with this material, gives our speakers the advantage of longer play times with lower weights
• STAMPED BASKET: The stamped basket offers a strong and rigid platform allowing the listener to hear clean and clear music output
• SPECIFICATIONS: Resonant frequency - 39 Hz, Sensitivity SPL (1W/1m) - 87 Db, Depth 11” x Width 11” x Height 5.3”
• WARRANTY: Planet Audio provides a powerful 3-year platinum online dealer warranty so long as the purchase is made through Amazon.com. We strongly encourage professional installation of this product to ensure proper and safe functionality

User questions & answers

Question:	How many does this item come with 1 subwoofer?? Or 2 subwoofers
Answer:	This speaker has high and low level inputs. High level inputs meaning speaker wire input and low level input meaning rca connections. In the box there is a wiring harness for the subwoofer. That harness has power, ground, remote, and speaker wires. Depending on your installation you can just tap into your rear speakers wires and run the new wires to the high level inputs (which are the speaker wires in the harness) or you can use the rca connectors (these came in my box it's speaker wire on one end which you tie into the speaker wires in the harness and a single rca on the other end. So either way you're good to go and honestly this subwoofer is impressive. I put this in a 2013 explorer and it pounds! Super clear too! Very easy to install!
Question:	Will this fit a 2002 explorer
Answer:	The wiring kit is solid separately. Get something that can handle a 800 watt peak capable kit. Rockville does sell amp wiring kits off their website, you can look it up off Amazon's site via part number. I went to Walmart and got a kit that can handle it for 25 bucks.
Question:	What is the true rms? looking to hook it up to a pioneer 1000watt 300rms amp
Answer:	What type of outputs does the soundbar have? If they're RCA and labeled something along the lines of "sub out" then you can.
Question:	can these subs be mounted Open Air and still have decent sound? I need somw subs for my boat, they would mount on the engine hatch
Answer:	Yes. That's realistically the only reason you would use speaker-level inputs, to have an adjustable crossover for situations where the upstream electronics don't offer it.

Product features

ANARCHY AC10D

A new subwoofer must go through a short but important process of 'break-in' before it is run under harsh conditions. This will ensure the performance as it has been designed to. The process involves subjecting the subwoofer to no more than low-to-medium volume levels for a number of hours in the enclosure. This will loosen the suspension to prevent the voice coil from overheating. Over-driving the woofer before it has been broken-in, will result in premature failure and poor performance.

• This ultra-thin subwoofer is designed to be placed at the bottom of the car seat, bringing you a more wonderful journey experience.
• Tuned by a senior sound engineer, it has strong and elastic low frequency, which makes every note vibrate in your ear.
• The two-in-one configuration of the power amplifier and the loudspeaker makes the installation in one step and saves the space inside the car. It has an ultra-thin thickness of 2.7 inches and can be installed under most car seats.
• We provide you with high-quality super-long cables and control wires, so you don't need to buy other accessories.
• Our products have been tested strictly and have reliable quality.

User questions & answers

Question:	Does this need to be wired directly to the car battery or can you use 12v inside car
Answer:	This definitely needs to have the main power wired directly to the positive battery terminal using heavy (at least 10 AWG) wire, with a fuse of around 30-40 amps as close to the battery as possible (within 12 inches) to protect the power wire in case of accidental contact with ground. The negative also needs to be heavy gauge wire with but can go to the nearest good chassis ground (I used a seat bolt with the paint sanded down to bare metal. Mine came with a suitable length of positive and ground cable, an AGU style fuse holder with a fuse for under the hood, and all necessary wire terminals.
Question:	Can you use two of these together
Answer:	I'm sure you could if you can split the bass signal from head unit. Would also have to run dual power lines or upgrade to larger gage then use a distribution block.
Question:	Is amp d class, how many watts RMS
Answer:	10in sub that's powered by a class D for 99 bucks. you'd probably demand the rms to be CEA-rated&compliant, too! I LIKE YOUR STYLE.
Question:	Does this come with the connector for the high level inputs? I don’t see it in any of the picture, just curious. Thank you
Answer:	hi ,you can see it in the last picture.

• Cone - Made from Polypropylene, the AR100DVC 10-inch car subwoofer provides a resilient and durable material that can offer great sound with the advantage of long-lasting subwoofers
• Voice Coil - Our voice coils are able to withstand high temperatures yet maintain its strength and fatigue properties. Making our voice coils with this material, gives our speakers the advantage of longer pay times with lower weights
• Surround - We use rubber in a lot of our subwoofers. It has the ability to endure much punishment without any sign of damage. It complements the whole structure of the speaker by allowing constant abuse where it is most needed, without the wear and tear.
• Basket - A Stamped basket frame is able to absorb and transfer much of the energy produced by the speaker. It has good corrosion resistance, good mechanical property, high thermal and electrical conductivity and retains strength at high temperatures
• Specs - Resonant frequency: 36 Hz, Sensitivity SPL (1W/1m): 85 Db, Impedance: 4 Ohms, Port frequency: 38. 2 Hz, Dimensions: 11” x 11” x 5. 4”, Mounting Depth: 4. 8”, Mounting hole: 9. 1”, Weight: 7. 6 Lbs.
• - BOSS Audio Systems provides a powerful 3-year platinum online dealer so long as the purchase is made through . We strongly encourage professional installation of this product to ensure proper and safe functionality

User questions & answers

Question:	Que amplificador necesito para un par de bocinas de estas
Answer:	It is possible for the P100f to work well in ported box. Thank you.
Question:	Does it come with a box
Answer:	It fit perfecty in the spot of the old sub. I don't use a box. My stereo is extremely adjustable . If my stereo was basic it might not work. I love it and it goes well wih my 4 inch speakers. Its like I have a comcert in my car . Unbeatable price for what the sound it puts out
Question:	What's the measurement from the bottom of the lip to the bottom of the magnet
Answer:	The CX122 is sold as a single subwoofer.
Question:	What’s the rms watts
Answer:	Hello, The CX8 should be a great fit being it matches the 8-inch dimension of your current speaker. Thank You!

• 🔈 RUBBER SUBWOOFER TRIM RING GASKET: Rubber Subwoofer Trim Ring Gasket We’re all about the details here at NVX. That's why we include a rubber trim ring gasket with our N-Series subwoofers. The trim ring provides a tight seal against the sub and the box it is being mounted to, in order to prevent air pressure from passing between the two.
• 🔈 SURROUND & SUSPENSION TECHNOLOGY: We’re all about getting the most bang for our buck, a key reason why we chose to include high-roll foam surround technology in the N-Series woofers. The surround itself is constructed with high excursion foam, which keeps the inward movement of the surround perfectly symmetrical with the outward movement.
• 🔈 ULTRA-LIGHT NON-PRESSED PAPER CONE: After testing scores of different cone materials, we decided on a custom blend of fine Ultra-Light Non-Pressed Paper fibers. This stiff yet lightweight material produces spectacularly accurate bass with a rich, natural tonal quality prized by audiophiles. The smooth matte finish of the cone offers a sleek, modern accent to the interior of any car.
• 🔈 2” HIGH-TEMPERATURE ALUMINUM VOICE COIL: The stout 2" high-temperature voice coil is constructed from a copper wire wrapped around an aluminum former. This industry-standard design is powerful enough to readily drive the cone with strict linear control, yet at the same time remains efficient enough for the compact, space-saving magnet structure.
• 🔈 HIGH-ENERGY FERRITE MAGNET MOTOR STRUCTURE: We chose a highly magnetized single stacked Ferrite magnet for the motor structure in the new N-Series. This magnet allows for greater power handling and voice-coil control during high excursion limits.

User questions & answers

Question:	Any one buy these subs? Are they any good
Answer:	I had one great sound
Question:	Will a skar 350 watt rms wired to 1 ohm from a dual 2 ohm version of one of these work good
Answer:	Yes, just don’t overpower this subwoofer too much. I blew mine in 2 days, but it was my fault. Good sub , just stay around required RMS.
Question:	How deep is this sub I have a truck box under the back seat and the deepest I can go is 4inch will this fit
Answer:	Naw these won't fit. You need shallow subs. You won't get the same sound with shallows, but they'll still sound really good in a truck with the space they need.
Question:	How many watts(RMS)will two of these handle
Answer:	If your running sealed box you can do 800 RAM to the pair if you're running ported I would run 600RMS

Product description

General Features:

•  Alpine SWT-S10 Single 10" Bass Tube Subwoofer - 1200 Watts 
•  Power Handling @Peak: 1200W Total 
•  Power Handling @ RMS: 250W Total 
•  Final Impedance: 4 ohms 
•  Preloaded with a single 10" Subwoofer 
•  Sealed enclosure with black carpet 
•  Enclosure Dimensions: 11.22"W x 23.6" D 
•  Passive Design (Non Amplified) Push SPK Terminal 
•  Voice coil size/type 
•  Frequency Response: 35-200 
•  Sensitivity: 90dB 
•  Enclosure Features:Tube enclosure 
•  Black Carpet Finish with White Alpine Logo 
•  Grille Included 
•  Brand: Alpine
•  MPN: SWT-S10
•  Type: Enclosed Non-Powered
•  Speaker Size: 10"
•  RMS Power: 250W

• Brand: Alpine
• MPN: SWT-S10
• Type: Enclosed Non-Powered
• Speaker Size: 10"
• RMS Power: 250W

User questions & answers

Question:	Is this enclosure sealed or ported? The title says sealed, but the description indicates it is ported
Answer:	Yes it is ported.
Question:	How is the sub holding up so far? most of the time i buy these its for the tube. the sub is a throw away and i buy a better one
Answer:	I'm happy w the sub and the tube. The tube is designed for the sub by Alpine engineer's for the best sound, that's why they're sold together.
Question:	Did it come with a mounting rack? If not where do i evem look for one
Answer:	It came with a mounting straps, you wrap the straps around the tube and then screw in an attachment so the strap won’t move. Works great and the base tube doesn’t move at all. Hope that answers your question.
Question:	Does it come with a mounting bracket
Answer:	No it comes with straps.

Product description

Description of RVB10.1A: The Rockville RVB10.1A is a 10" powered subwoofer that gives you everything you from a car subwoofer. This is a complete system with the subwoofer enclosed in a box along with a built-in amplifier. This system will give you more bass in your car or truck, without giving up tons of space.This subwoofer has a tight suspension and it produces a super clean and controlled bass response that sounds incredible.Installation is quick and easy since this is an all in one system. High level and low level inputs allow you to wire this system to the RCA output of an aftermarket radio or to the high level inputs of a stock radio.Our engineers used sophisticated computer modeling and created a ported enclosure for a 10" woofer that sounds better than most 12” subs.Turbo tuned with an aerostyle port you will be astounded at the bass output this little bass enclosure produces. We are talking about low bass frequencies that you can feel. In most cases packaged systems put out weak bass that is not deep. Our Rockville subwoofer was engineered and tuned to put out punchy bass.Powered by a powerful built in Class AB 300 Watt RMS amplifier the RVB10.1A will keep you rocking with clean power. We also eliminated air or mechanical noise that you do not want to hear. This system features an electronic low pass crossover that is fully adjustable so that you can customize it for your car's listening environment. You can tune the sub to only play frequencies that your full range speakers are not handling. Also featured is an adjustable bass boost EQ.If you want loud and tight bass in an all-in-one package that will fit in a relatively tight space, then the Rockville RVB10.1A is the system for you!

• Rockville RBV10.1A Single 10” 500 Watts Active Subwoofer Enclosure, Size: 10”, Peak Power: 500 Watts, RMS Power: 300 Watts, Nominal Impedance: Single 4-Ohm, 1.5” Voice Coil, Inverted Carbon Graphite Molded Dust Cap, Kevlar Reinforced Pulp Cone, Double Lami
• Frequency Response: 35Hz - 200Hz, Sensitivity: 88dB, Anti-Vibration Braced MDF Cabinet, Angled Back Fits Perfectly Against Rear Seats, Computer Tuned Bass Reflex Port, Blue/Black Aviation Grade Tweed Carpet with Embroidered Rockville Logo.
• Class AB Amplifier, High Speed MOSFET Power Supply, High Level Speaker Inputs, Low Level RCA Inputs, Built-In Low Pass Crossover (30Hz - 160Hz).
• Accepts up to 8 Gauge Wire, 100mV - 5V Input Voltage, Power (Blue) & Diagnostic (Red) LED Indicators, 20A Fuse, Dimensions in inches: Length 15.75" x height:12.99" x top width 10.63" x bottom width:14.17", Weight: 22.59 lbs.

User questions & answers

Question:	Will it work in a 2002 Pontiac Sunfire
Answer:	It should work in anything you plug it into, as long as it fits
Question:	can i use it with a receiver
Answer:	If you are referring to an aftermarket head unit or factory radio in a vehicle then yes. If you are talking about a home stereo then no.
Question:	Could you upgrade the amp later on? Add another with the existing one or change it out altogether
Answer:	You could certainly add another . Sounds great for a small car. Upgrading the amp prob not a great idea
Question:	Does this sound better than the 10" bass tube
Answer:	Yea it has a great sound to it. More than i expected..

Product features

Rockville RVB10.1A 10 Inch 500W Active Powered Car Subwoofer+Sub Enclosure Box

The Rockville RVB10.1A is a 10" powered subwoofer that gives you everything you from a car subwoofer. This is a complete system with the subwoofer enclosed in a box along with a built-in amplifier. This system will give you more bass in your car or truck, without giving up tons of space.

This subwoofer has a tight suspension and it produces a super clean and controlled bass response that sounds incredible. Installation is quick and easy since this is an all in one system. High level and low level inputs allow you to wire this system to the RCA output of an aftermarket radio or to the high level inputs of a stock radio. Our engineers used sophisticated computer modeling and created a ported enclosure for a 10" woofer that sounds better than most 12” subs.

Turbo tuned with an aerostyle port you will be astounded at the bass output this little bass enclosure produces. We are talking about low bass frequencies that you can feel. In most cases packaged systems put out weak bass that is not deep. Our Rockville subwoofer was engineered and tuned to put out punchy bass.

Powered by a powerful built in Class AB 300 Watt RMS amplifier the RVB10.1A will keep you rocking with clean power. We also eliminated air or mechanical noise that you do not want to hear. This system features an electronic low pass crossover that is fully adjustable so that you can customize it for your car's listening environment. You can tune the sub to only play frequencies that your full range speakers are not handling. Also featured is an adjustable bass boost EQ.

If you want loud and tight bass in an all-in-one package that will fit in a relatively tight space, then the Rockville RVB10.1A is the system for you!

Features:

• Rockville RBV10.1A Single 10” 500 Watts Active Subwoofer Enclosure
• Size: 10”
• Peak Power: 500 Watts
• RMS Power: 300 Watts
• Nominal Impedance: Single 4-Ohm
• 1.5” Voice Coil
• Inverted Carbon Graphite Molded Dust Cap
• Kevlar Reinforced Pulp Cone
• Double Laminated Foam Surround, Stitched to Cone
• Frequency Response: 35Hz - 200Hz
• Sensitivity: 88dB
• Anti-Vibration Braced MDF Cabinet
• Angled Back Fits Perfectly Against Rear Seats
• Computer Tuned Bass Reflex Port
• Blue/Black Aviation Grade Tweed Carpet with Embroidered Rockville Logo

Product description

We are an Authorized PLANET AUDIO Dealer! These TWO PLANET AUDIO **AC10D** 10" 300W Dual 4-Ohm Voice Coil Car Audio Subwoofers can handle 1500 Watts of MAX power per sub (3000 Watts per pair) and 750 Watts of RMS power per sub (1500 Watts per pair). Thump your car audio system with these **AC10D** subwoofers!

• 2) NEW PLANET AUDIO **AC10D** 10" 3000W Dual 4-Ohm Voice Coil Car Audio Subwoofers
• MAX Power Handling: 1500 Watts per sub (3000 Watts per pair)
• RMS Power Handling: 750 Watts per sub (1500 Watts per pair)
• Frequency Response: 23Hz
• 3kHz

User questions & answers

Question:	Can I put a Planet Audio 2500w amp on these speakers
Answer:	Here's the thing about audio amps/speakers . A given speaker will be rated for a certain amount of power but that is a general guideline. So if You have a more powerful amp than speakers rating most likely You can drive that speaker with at least some more power than speaker rating up to the point of undesirable distortion and back off just a little for safe operation that will generally last the long term. Anytime You hear distortion You run the risk of burning the voice coil wiring . This explanation although true is also a general guideline. Just make sure to back off volume from the point You hear a little distortion and Your speakers should last.
Question:	What is the Max mounting depth
Answer:	5.3 inches
Question:	What Size wire do you recommend to hook these up? Thanks
Answer:	Thicker tha wire better tha response and sound...I personally run 6 or 8 gauge because I'm okay with the thump and not boom or pound
Question:	Can it handle a Planet Audio 2500 set at 2 ohms
Answer:	Yes easily