13 best switch encoders

Product description

Length of Shaft: 20mm/ 0.79in

5 pins



Package Includes:

5× Rotary Encoder Code Switch Digital Potentiometer

5× Knob Cap

• Length of Shaft: 20mm/ 0.79in
• 5 pins

User questions & answers

Question:	Any tech data at all? output voltage? detent? ppr? gray code? shaft dia? sheesh why would you buy this not knowing any of these things
Answer:	ive got them and its pretty clear their a c11 type encoder like you might get from adafruit, cheap components r good on a budget for a hobby project but id definitely get something that atleast better specifies what it is if the application is any more critical than that
Question:	Can you provide pinout information for this
Answer:	Sorry answer was cutoff. The tutorial here http://bildr.org/2012/08/rotary-encoder-arduino/ shows a "generic" wiring diagram that works well.
Question:	Is there a datasheet for this
Answer:	Wasn’t able to find one
Question:	Where might I find the connection terminal information for these rotary switches? None came with them in my order. There are no labels on the switch
Answer:	I'll do the best I can without photos. One side has two pins. That is the pushbutton +&- (positive & ground). simple What's hard is the 3 pin side. A, C, B (left, center, right). A connects to CLK (GPIO pin) directly, and is also connected to a + bus via a 330Ohm resistor B connects to DT (GPIO pin) directly & is also connected to the + bus via 330Ohm resistor C connects directly to ground So you have two wires going to ground (one on each side), the remaining 2 pins on the 3 pin side going to GPIO pins & a +(GPIO pin) connected to a bus supporting the CLK & DT pins. The remaining pin on the 2 pin side goes to a GPIO pin for the pushbutton switch (thus 3 GPIO pins). The diagram makes it so much easier (sad face) regardless, you still need some code to make it work. Really interesting that there is no electronics or logic in the rotary encoder. Just good old analog contacts managed by code.

Product description

Specification:

Type: KY-040 Rotary Decoder Encoder

Operating Voltage: 5V

One round number of pulse: 20

Width: 19mm

Length: 30mm

Height: 28mm

Material of Knob Cap: Aluminium Alloy

Diameter of Knob Cap: 14mm

Height of Knob Cap: 17mm

Package includes: 2 x KY-040 Rotary Decoder Encoder



Pin description:

CLK - equivalent to output A in regular encoder.

DT - equivalent to output B in regular encoder.

GND - equivalent to output C in regular encoder.

SW - reset switch.

+ (VCC) - positive supply to the unit.

The KY-040 rotary encoder is a 360 degree rotary input device (i.e. a control knob) that provides an indication of how much the knob has been rotated AND which direction it is rotating in.

It is a great device for stepper and servo motor control. You can also use it to control devices like digital potentiometers. It is ideal for navigating menus on a display or taking inputs such as numbers or text characters. The range of input can be easily defined and mapped in software. A push button switch is built into this encoder.

If you push on the shaft, the normally open switch "SW" will close. This can be used as an On/Off switch, to change control functions, ranges, selecting a menu item or entering a number. The "D" shaft of the encoder can be fitted with a knob for using it in a product.

• Type: KY-040 Rotary Decoder Encoder
• Operating Voltage: 5V; One round number of pulse: 20
• Size: 30x19x28mm(LxWxH); Package: 2 x KY-040 Rotary Decoder Encoder
• No limitation on rotation counts
• The encoder can be reset to its initial state, that starts counting from 0 with the button on the rotary

User questions & answers

Question:	What is the diameter of the shaft
Answer:	6 mm

• ✔Product type: DC Gear motor with two-channel Hall effect encoder;Rated Voltage: 12V; No-Load Speed: 10RPM; No-Load Current: ≤ 0.15A;Rated Torque: 12kg.cm;
• ✔Main Body Dimensions:74.8 x 25mm / 2.95in x 0.99in (L*D); Out Shaft Dimensions: 11 x 4mm / 0.433 x 0.1575in (L*D) with 10 x 0.5mm / 0.39 * 0.017inches flat cut off;
• ✔Single Output 5736 Pulses Per Revolution: Gear Reduction Ratio: 1/478, Each Loop Output Pulses: 12PPR 478*12=5736PPR;
• ✔Wiring Diagram: Red - Motor power terminal (+);Black - Motor power terminal(-);Green - Quad encoder Ground;Blue - Quad encoder +5V Vcc;Yellow - Quad encoder A signal;White - Quad encoder B signal.
• ✔Application:Suit for Projects Such as Robotics,RC Car Model,Custom Servo, Arduino and 3D Printers,DIY Engine Toy.

Product description

A rotary encoder, also called a shaft encoder, is an electro-mechanical device that converts the angular position or motion of a shaft or axle to digital output signals. Rotary encoders are used in a wide range of applications that require monitoring or control, or both, of mechanical systems, including industrial controls, robotics, photographic lenses, computer input devices such as optomechanical mice and trackballs, controlled stress rheometers, and rotating radar platforms.



Specifications:

Model: EC11 ultra-thin

Type: Encoder code with Switch

Adjustment method: 360 Degree Rotary

Pins: 5

Number of digits: 20 digits

Shaft diameter: 6mm/0.24inch (Threaded to accept locking nut)

Length of Shaft: 20mm/ 0.79inch



Package Included:

10× Rotary Encoder Code Switch Digital Potentiometer 10×Orange Knob Cap

• Type: Encoder code with Switch; Adjustment method: 360 Degree Rotary; Number of digits: 20 digits; Pins: 5.
• Shaft Diameter: 6mm/0.24inch; Shaft Length: 20mm/0.79inch.
• In the forward rotation, the A line phase leads the B line phase; when reversed, the B line phase leads the A line phase. The phase relationship and number of rotations of AB can be identified using a simple digital logic circuit (exclusive OR gate and D flip-flop).
• According to the timing diagram, it is not rigorously summarized as the falling edge of the clock, A and B are the reversed phase is forward rotation, and the same phase is inverted.
• Applications: Industrial controls, robotics, photographic lenses, computer input devices such as optomechanical mice and trackballs, controlled stress rheometers, and rotating radar platforms.

• ★Product Name: Encoder code with Switch; Adjustment Method: 360 Degree; Pin Numbers: 7; Rated Voltage: 5 V.
• ★Shaft Diameter: 6mm/0.24"; Shaft Height: 20mm/0.79"; Thread Diameter: 6.8mm/0.27".Shaft Movement Direction: Action Type: Momentary.
• ★Material: Plastic, Metal; Main Color: Blue, Silver Tone.Shaft type: Plum blossom handle
• ★Application: for industrial controls, robotics, photographic lenses, computer input devices
• ★Package Content: 10 x EC11 Rotary Encoder with Switch and Knob Caps. (20MM).

User questions & answers

Question:

What is the pin-out for these encoder switches

Answer:

I haven't used them, but I would guess that they have the same pinout as the ones in this link. I would check them with an ohm meter or breadboard before soldering them in. https://www.amazon.com/Anmbest-Encoder-Digital-Potentiometer-Raspberry/dp/B07MW7D4FD/ref=pd_sbs_328_6/130-7698180-5793042?_encoding=UTF8&pd_rd_i=B07MW7D4FD&pd_rd_r=5f8c2b76-276c-4e27-8691-b15b1d2e65ed&pd_rd_w=6wOr7&pd_rd_wg=ffM1o&pf_rd_p=b65ee94e-1282-43fc-a8b1-8bf931f6dfab&pf_rd_r=BS1ZP9VVXEKJCRJECW5N&psc=1&refRID=BS1ZP9VVXEKJCRJECW5N

Product features

Specification:

Product Name: Encoder Code with Switch

Pin Numbers: 7

Rated Voltage: 5 V

Shaft Diameter: 6mm/0.24"

Shaft Height: 20mm/0.79"

Thread Diameter: 6.8mm/0.27"

Total Dimension: 15mm x 12.5mm x 30mm / 0.59" x 0.49" x 1.18"(L*W*H)

Description

Material: Plastic, Metal

Main Color: Green, Silver Tone.

Action Type: Momentary

Adjustment Method: 360 Degree

Please Note: Do not touch the product with water

Package Content:

• 10 * EC11 Encoder Code with Switch 20mm
• 10 * Knob Cap
• 20PSC nuts
• 20PSC washers

Product description

Include:

1x Encoder,

1x USB Cable,

1x 5pin Cable,

13x 2pin 2.8mm snap Cable.

17x 2pin 4.8mm/0.187inch snap Cable.

2x 3D Analog Joystick,

2x 6pin Analog Joystick Cable. One of 2pin for L3/R3.

• 3D joystick for flight simulation games, Analogue Stick Thumb sticks Joystick Cap Mushroom Head.
• Developed for Nintendo Switch game console. DIY your Nintendo Switch controller.
• Suitable for PS3, Nintendo Switch, Raspberry Pi, Retropie, MAME and all windows systems! Hold the Mode key for 5 seconds to switch to mode.
• Make sure to open Pro Controller Wired Communication on the Nintendo switch settings page
• Size:Board 8.5cm(9cm with USB Plug) x 3.5cm. USB Cable 180cm. Button and Joystick Cable 20cm.

User questions & answers

Question:	Will this work with the nintendo wii
Answer:	I wear reading glasses while gaming or bing watching videos on line, for hours. these are awesome headphones.
Question:	I'm having issues with the joysticks constantly scrolling up when plugged into a Nintendo switch. Is there a way to reset or update the board
Answer:	For most modern 3D games designed for HD tvs, you won't notice any lag at all (Zelda BofW, Mario Odyssey). However, play something that requires incredible precision, like MegaMan 11 (which seems to require the sharp timing of the older CRT-intended games), and you will notice enough lag to get you killed when using a wireless controller. For this game specifically, I used a wired controller with this adapter and the difference is noticeable.

Product description

The rotary encoder can count the number of pulse output during rotation in the positive direction and reverse direction through the rotation and this rotation counts are not limited. With the key on the rotary encoder, you can reset to the initial state, that is, counting from 0. The Material of Knob Cap: aluminium alloy

• Working voltage: 5V; One round number of pulse: 20
• The Material of Knob Cap: aluminium alloy；The Specification of Knob Cap: diameter: 15mm/ 0.59in; height: 16.5mm/ 0.65in
• The rotary encoder can count the number of pulse output during rotation in the positive direction and reverse direction through the rotation and this rotation counts are not limited
• With the key on the rotary encoder, you can reset to the initial state, that is, counting from 0
• Package content: 5pcs x Rotary Encoder Module + 5pcs black Knob .

Product description

Product description



Specifications:

Product Name:Mouse Encoder Switch

Switch Type:Micro Switch

Material:Plastic, Metal

Size: 17x11x6mm/0.67x0.43x0.24Inch

Color:Black,Silver Tone

Package Content:5 PCS



Feature:

The mouse encoder is the same as the universal height encoder, with high precision, precise positioning, scale feel, and very comfortable feel.

Suitable for office games, e-sports.

• Product Name:Mouse Encoder Switch.Switch Type: Micro Switch.
• Material:Plastic, Metal.Color:Black,Silver Tone.
• Size: 17x11x6mm/0.67x0.43x0.24Inch.Package Content:5 PCS.
• The mouse encoder is the same as the universal height encoder, with high precision, precise positioning, scale feel, and very comfortable feel.
• Suitable for office games, e-sports.

• Zero delay arcade game USB encoder board by SJ@JX.
• Developed for Nintendo Switch game console. DIY your Nintendo Switch controller.
• Power 5V supply and cable, making LED assembly very simple!
• Suitable for PS3, Nintendo Switch, Raspberry Pi, Retropie, MAME and all windows systems!
• Make sure to open Pro Controller Wired Communication on the Nintendo switch settings page

User questions & answers

Question:	I saw a video showing these boards are not compatible with super smash bros, Do you sell a newer version of this board that supports that game
Answer:	Yes, the LEGO Marvel Collection will include the DLC that was released for each game.
Question:	Is there anything else needed to play with this on the nintendo switch? I've plugged everything in and the usb into the switch. Nothing is happening
Answer:	Yes it does!
Question:	Do you sell just the encoder boards
Answer:	Two players can enjoy LEGO Star Wars: The Force Awakens together.
Question:	What is the difference between sanwa style 1 and
Answer:	I dont know but - you go to the menu in the PlayStation and change it - the language can be set to any one you want - if you speak spainish it will allow you to play I spanish as well as your menus will be in that

Product features

Nintendo switch encoder with LED power supply.

• Applicable to multiple game systems.
• They all contain the same functions.
• This series differs only in colors and cables.

Product description

These are continuous rotary encoder switch with a built in push button switch (push to operate). they can be used for data entry.

User questions & answers

Question:	is it possible to cut the overall length to 25mm
Answer:	From the base of the encoder to the tip of the encoder shaft total length is 20mm. The shaft it self is 6mm long. The shaft is a D shape. Hope this help you! Cheers....
Question:	when rotated, does it connect the center pin and either the left or right (spin direction) ... like a momentary switch hit over + over? or different
Answer:	No. The rotary encoder side has three pins. The center pin is connected to ground and the outer pins are signal pins. The momentary switch side has two pins and are connected as you would any switch. The single pins on the other two sides are not electrically connected, but are used for mechanical connections.
Question:	Do these come with the hardware to mount them (bolts for the threading
Answer:	Mine came with nuts and washers

• Zero delay arcade game USB encoder board by SJ@JX.
• Developed for Nintendo Switch game console. DIY your Nintendo Switch controller.
• Easy Installation Design! Just connected the push button and joystick, really plug and play!
• Suitable for PS3, Nintendo Switch, Raspberry Pi, Retropie, MAME and all windows systems!
• Make sure to open Pro Controller Wired Communication on the Nintendo switch settings page

User questions & answers

Question:	Does this work with a nintendo swich
Answer:	Yes, 100% support.
Question:	Will this work with Xbox
Answer:	not suit for Xbox
Question:	Just bought your encoder for the switch, how can i switch from d-pad use to analog
Answer:	Yes, you can contact customer service. It requires new versions to be updated by OTAs.
Question:	Is there an input on the board that corresponds to the Home button for Nintendo Switch
Answer:	YES

Product features

Other products in the same series.

• Including an extended print head.
• One player version.
• Two players version kit.
• All coding boards in this series are the same. You can choose the color and cable you like.

Product description

Load device is working, winding resistance caused by large current, will produce very, very high temperature, therefore in the process of use, and just use the finished in a short period of time, absolutely can not human exposure golden metal radiator parts, to avoid the scald!Nor to flammable items contact tester, in order to avoid the fire!In use process must be highly vigilant!

Considering the particularity of heat resistance, the initial use of electricity after a period of time will appear a few white smoke and smell, because outside the paint contains very little moisture, high temperature electric heating, moisture evaporates form the phenomenon of white smoke, produce peculiar smell by high temperature baking paint outside phenomenon, completely disappear after using for a period of time.This phenomenon is inevitable, belongs to the normal situation, do not have to worry about load tester can damage, please be assured that use.

The load application

Can be convenient to test mobile power charging treasure, mobile phone charger, USB power output current is such as to amount to mark, so long as connect USB above.And can do it for mobile power supply and USB power adapter aging test, aging test discharge resistance will be hot, temperature is controlled in 80 ~ 85, please pay attention to prevent hot!

Total Size: 15 x 11 x 6mm / 0.59 x 0.43 x 0.24inch (L*W*H)

Quantity: 5 Pcs



Package Contents:

5 x Encoder Switch

• Net Weight: 5g; Package Content: 5 x Encoder Switch
• Main Color: Black,Silver Tone
• Total Size: 15 x 11 x 6mm / 0.59" x 0.43" x 0.24" (L*W*H)
• Country of Manufacture: CHINA
• Material: Plastic,Metal