14 best 2 ton floor jacks

Product description

Fit Under Low Ground Clearance Vehicle

Pro-Lift F-767 Grey Low Profile Floor Jack is a 2 Ton floor jack that give you better access to low ground clearance vehicle. And,give you the lifting range from 3-1/2 inches to 14 inches.

The Jack can be fit under a clearance of 3-1/2 inches and maneuvered easily into position.

Pro Lift F-767 floor jack also features the heavy duty steel construction that provides the long lasting durability.

Pro Lift unique patented bypass device protects against over pumping. Its built-in safety valve provides overload protection.

- Extra Low Profile

- Lifting Range from 3-1/2 inches to 14 inches

- Patented bypass device protect over pumping

- Built-In Safty Valve Provides overload protection

Pro Lift F-767 floor jack is backed with SFA 90 Days Warranty from the Date of Purchase.

Take one now to access to the areas you never access before.

• Extra low profile
• Lifting range of 3-1/2 inches to 14 inches
• Patented bypass device protects against over pumping for safe operations
• Built-in safety valve provides overload protection. Rust Resistant
• Heavy duty steel construction provides long term durability

User questions & answers

Question:	Does it come with a portable case
Answer:	No, but the box it comes in is pretty sturdy. If you remove the cardboard packing the jack easily slides back into the box. The inside bottom of the box is reinforced. Not sure how long it will hold up, but it’s better than nothing.
Question:	Will this raise a 2011 cadillac cts enough to get jack stands underneath it? i want to change transmission oil ... thanks
Answer:	A Cadillac CTS is roughly 4,300 pounds. Which is a little over the capacity of this jack. As long as you're placing it on jack stands and you don't leave the jack holding it too long, it should be okay. Although all the armchair experts on this site will implore you to buy a 3 or 4 ton jack. Just remember to always put the car on jack stands and do your work on a flat, level surface.
Question:	Can anyone tell me the outside diameter of the lifting cup? Thanks
Answer:	The cup itself is 2 1/4 inches, with the inner portion (The part that spins freely, with the 4 tabs) 1 7/8ths, and the tabs extend about 1/4 inch up from the cup. Hope this helps.
Question:	What kind of oil does this take? The screw was loose when it was shipped to me and some oil had poured out into the box. I just want to top it off
Answer:	hydraulic jack oil. The screw IS loose upon arrival. If you read the SHORT instructions....this (grey) screw is HOW TO LOWER the jack when you are done lifting and have supported the weight/vehicle with jack stands. Turning just a bit using the handle you used to pump up the vehicle - you will notice it lower ever so gently. ONCE it is fully lowered - it is best to immediately turn the screw clockwise until it stops - this prepares the jack for its next use. Do this so you will not forget it is closed. IMO - some people with oil spewing - did not 'get it' how important it is to assure the valve is closed BEFORE raising the vehicle.

Product features

Pro-Lift F-767 Grey Low Profile Floor Jack - 2 Ton Capacity

About Us:

Our ProLift hydraulic automotive jacks, lifts and garage equipment range will cater to many 'do it yourself' enthusiast. The product line includes bottle jacks, floor jacks, garage jacks, aluminum jacks. scissor jack, lawn mower lifts, utility lifts, chokes, dirt bike lift, creepers, mechanic seats and more! Explore our range on the products page.

ProLift has become a global presence in the go to automotive garage maintenance equipment with locations in the United States, The Netherlands, Taiwan and Australia. We create dependable and reliable performance hydraulic equipment.

Product description

Fast Lift to the Jacking Point

Blackhawk B6350 Service Jack is a 3-1/2 ton (7,000 lbs) capacity service jack that features the unique design of fast list technology to fast lift to the jacking point with no load.

It features the swivel saddle that provides you with the easy jack positioning and user safety. Its heavy duty steel construction also provides you the safe use and long term durability.

Blackhawk B6350 Service Jack also features the bypass device that preventing the damage from over pumping.

Blackhawk B6350 Service Jack also features the built-in internal safety valve and vent plug to ensures the safe operation.

- 3½Ton (7,000 Lbs.) Lift Capacity

- Fast Lifting Technology

- Heavy Duty Steel Construction & Swivel Saddle

- Built-In Safty Valve and Bypass Device

Blackhawk B6350 Service Jack is backed by the full one year warranty from the date of the purchase.

Click the buy button now to get your long lasting professional sevice jack

• Built-in internal safety valve and vent plug ensures safe operation
• Swivel saddle provides easy jack positioning and user safety.Saddle Diameter: 4 inch
• 3.5-ton/7,000 lb. lift capacity
• Jack Size: 28 1/2" L x 13 3/4" W x 6 1/2" H
• Rugged universal joint for precise load control
• Great for working in the garage and other outdoor activities such as picnics or ball games
• Note: The hydraulic jack is designed to lift, not to support the object. Immediately after lifting, loads must be supported by a pair of appropriately rated jack stands

User questions & answers

Question:	Hi, Wondering if it will fit my new XtremepowerUS 1/2 Ton Transmission Hydraulic Floor Jack Adapter it has a 1 1/4 inch hole
Answer:	I would say no. The hole in this jack only measures 1 1/8". It would seem your adapter needs an 1 1/4" hole for the "peg" to drop into .
Question:	How high does it lift
Answer:	The lifting range on the jack is 5.5" to 22" H.
Question:	Will this fit under a low profile car like a 350Z
Answer:	It's unlikely. I have a 2006 Mustang GT. If I'm not mistaken, a Mustang has about the same ground clearance as a 350Z. The jack will not fit under my Mustang. It's about an inch or two too tall. It is a great jack in spite of this. I use it on my other vehicle.
Question:	Anyone know of any jack that has this weight capacity, but is made in the USA
Answer:	My Blackhawk B6350 I bought 3 months ago has a made in the USA sticker. For whatever that means. Maybe to sticker was made here!

Product features

Lifting Range: 5.5 inches - 22 inches

• Note: Before it uses, it needs to make sure the release valve needs to be turned clockwise until the firm resistance is felt.
• Note: Since the hydraulic jack is designed to lift, not to support the object. Immediately after lifting, loads must be supported by a pair of appropriately rated jack stands

Product description

Pro lift F-2315PE hydraulic trolley jack has the 3000 lbs. capacity. It gives you the ability to lift from 5.25" to 12". it is built with All welded steel frame construction and rust-resistant. Large steel casters and swivel casters provide easy maneuverability.

• Min. Height: 5.25", Max. Height: 12"
• All welded Steel frame Construction with rust resistant
• Large Steel casters and swivel casters for easy maneuverability
• Sturdy carrying handle
• Blow mold case for easy storage

User questions & answers

Question:	Is it good for a 2016 lexus is 200t fsport
Answer:	This is a small jack that is good for something the size of a Camry. I did use it once on a Toyota Prado Land Cruiser with blocks of wood and it struggled. It is not commercial quality. and
Question:	Is this good for a 2012 chrysler
Answer:	good for any car with the clearance. always check your manufacturer owners manual for auto jack lift points. many cars use unibody construction and serious damage can occur if jack placed incorrectly.
Question:	Is it good for changing tire on riding lawnmower
Answer:	Don’t buy it... i did and it works only two times 👎
Question:	Is it good to use on a 2003 subaru outback wagon
Answer:	It’s garbage. Don’t waste your money. Spend a little more and get something that you can trust. Mine failed the first time trying to lift a compact car.

Product features

Pro-LifT

Our lifting equipment products have consistently led the industry in quality and innovation. Designed after professional grade equipment standards, Pro-Lift equipment is kept under close quality control standards from factory to your home. Our products provide a unique twist to your garage maintenance needs.

• 【JACK CAPACITY-3.0T/6600LB】- Weight capacity of 3 ton (6600 lbs) and lifting height 12.5-37cm (5"-14.6") low saddle, 17-42cm (6.7"-16.5") high saddle. With a 12V vehicle power outlet. Powerful and time-saving toolset with Wireless Remote.
• 【EASY TO USE】- Simple operation, highly practical and high safety factor. Farewell to laborious and tedious manual dismounting.
• 【RUGGED CONSTRUCTION】- Made with premium materials and innovated technology, it is very durable and trustworthy.
• 【PORTABLE CASE】- Comes with a plastic storage case for easy transport and storage. The scissor jack comes with an impact wrench for tire replacing and an inflator pump.
• 【WIDELY USED】- Suitable for sedans, off-road vehicles, vans, light-duty trucks or any vehicle suits its capacity. It is also a favorable tool for garages, repair shops, and families.

User questions & answers

Question:	How much torg lbs does impact have
Answer:	Look at the hinge on the inside. They are at the bottom of the lid.
Question:	What is the shipping weight on this product
Answer:	Nope
Question:	Can i use for my rav
Answer:	I use it for the first time this week, and it work perfect i will give five star.
Question:	The air pump is for the car?? Cause it does not have enough pressure
Answer:	The image shows an adapter for the plug to clip to the battery. See images

Product features

Strong Performance

Weight capacity of 3 ton (6600 lbs) and lift range: 12.5-37cm (5"-14.6") low saddle, 17-42cm (6.7"-16.5") high saddle. With 12V vehicle power outlet. Powerful and time saving tool set with Wireless Remote.

Non-Slip Cross Recessed Ejector

This is solid and stable anti-slip ejector, free to adjust the height and starting height effortlessly, but also to stabilize the vehicle, ensure your safety and efficiency.

Easy to Use

One-button control. Simple operation, highly practical and high safety factor. Farewell to laborious and tedious manual dismounting.

Standard Accessory

With Inflator Pump, Tow Rope, Battery Clip, Wireless Remote, Multifunction Electric Hammer, Low Saddle, High Saddle, Suitcase and other accessories.

Carrying Case

Comes with a plastic storage case for easy transport and storage.

Wide Application

Suitable for sedans, off-road vehicles, vans, light-duty trucks or any vehicle suits its capacity. It is also a favorable tool for garages, repair shops, and families.

3 Ton Scissor Electric Jack

Electric scissor jack plus impact wrench set is able to work with car cigarette lighter power or car battery. By controlling lift switch, the mechanical part of the jack can be adjusted freely and smoothly, thus lifting car tires fast. Meanwhile, electric wrench can conveniently disassemble or fasten the fixing nut of different wheels and vehicles, only by a simple press of its start switch.

Product description

The Torin BIG RED T820014S hydraulic trolley floor jack is constructed with heavy duty steel, providing long term durability with an industrial luster. This floor jack has a 2 ton (4,000 lb) capacity and features a minimum lifting height of 5-3/5" and a maximum height of 13", which is ideal for most cars, trucks, and SUVs. A safety bypass system prevents over-loading and ensures safe operation. Equipped with large steel casters and 360-degree swivel casters for smooth maneuverability. The Torin BIG RED T820014S hydraulic trolley floor jack is equipped with a handle for quick portability. It includes a plastic blow mold carrying case for easy storage when not in use. Includes a limited 1 year manufacturer warranty.

• Hydraulic trolley floor jack is constructed with heavy duty steel, providing long term durability with an industrial luster
• Features a 2 ton (4,000 lb) capacity with a minimum lifting height of 5-3/5" and a maximum height of 13"; Ideal for most cars, trucks, and SUVs
• Safety bypass system prevents over-loading and ensures safe operation
• Equipped with large steel casters and 360-degree swivel casters for smooth maneuverability
• Includes a plastic blow mold carrying case for easy storage when not in use; Includes a 1 year limited manufacturer warranty

User questions & answers

Question:	Can it lift a 2003 Ford Crown Victoria
Answer:	yes
Question:	What rubber pad can you buy that fits this jack. So you dont bend your frame rail
Answer:	don't know......
Question:	can it lift a 2014 dodge journey
Answer:	NO,it can't lift your dodge journey.
Question:	will it lift a dodge journey
Answer:	Dodge Journey weights 3,818 lbs 1.732 tons. Which means yes as it is good up to 2 Tons.

Product features

Torin BIG RED Hydraulic Trolley Floor Jack with Carrying Case, 1.5 Ton (3,000 lb) Capacity

• Constructed with heavy-duty steel, providing long term durability with an industrial luster
• Features a 1.5 ton (3,000 lb) capacity, a minimum lifting height of 5-3/5", and a maximum height of 13"
• Safety bypass system prevents over-loading and ensures safe operation
• Equipped with large steel casters and 360-degree swivel casters for smooth maneuverability
• Includes a plastic blow mold carrying case for easy storage when not in use

Heavy-Duty Steel

1.5 ton (3,000 lb) capacity and features a minimum lifting height of 5-3/5" and a maximum height of 13"

Over-Load Protection

A safety bypass system prevents over-loading and ensures safe operation

360-Degree Swivel Casters

Equipped with large steel casters and 360-degree swivel casters for precise maneuverability

Carrying Handle

Equipped with a built-in carrying handle, allowing for the jack to be lifted quickly

Product description

The K Tool International 3 ton service jack provides a reliable and efficient way to lift in the shop.This service jack has the capacity to lift up to 3 tons or 6,000 lbs. This product is made of heavy duty steel and NOT Aluminum which separates our products from competitors. Nobody wants scuffed and scratched up floors. This service jack is fit with nylon wheels instead of metal wheels. This will help ensure your shop or garage floors won't scratch or scuff. Jack includes these different specs: Length: 24"; Chassis Width: 13.4"; Handle Length: 39.4"; Saddle Diameter: 3.75". Jack has built in valve system to prevent use beyond rated capacity and over extension of ram. This service jack's swivel rear casters make it easy to maneuver and position within the shop. Since 1984, K Tool International leads the market by ensuring that its products are rugged, reliable and reasonably priced. Since 1984, K Tool International leads the market by ensuring that our products are rugged, reliable and reasonably priced for any level of user and shop.

• [3 TON CAPACITY] Needing to jack your car or truck? This floor jack 3 ton is rated to lift up to 6,000 lbs.
• [LIFTING RANGE] Service jack has a lifting range of 5.5" - 18.75". This service Jack provides flexibility for a variety of automotive needs
• [BUILT-IN VALVE] The valve prevents over-extension of hydraulic ram and jack use beyond rate capacity. Added protection for the lift
• [SWIVEL CASTERS] The swivel rear casters and saddle provide smooth maneuvering and positioning around cars and trucks. Wide track front wheels provide stability while rear swivel casters provide easy maneuverability
• [NYLON WHEELS] Nylon wheels will protect the floor surface in the shop or garage. Aluminum wheels often scratch and scuff up shop and garage floors. Our wheel material prevents that

User questions & answers

Question:	Where is it made
Answer:	Well of course
Question:	what is the actual jack weight - not 65.9 pounds
Answer:	iwiss SN-28B
Question:	Jack delivered today. Inside the box was a short, fat, bolt that looks like it is a plug for the hydrolics. Where does it go
Answer:	Yes they are gold plated
Question:	Does this jack come with a box to carry around in so you do not have to carry the jack around yourself
Answer:	You have to have crimpers. No solder. Criminal on

Product description

Torin 2 Ton Hydraulic Trolley Jack offers a safety overload system to prevent use beyond the rated capacity which makes it highly reliable and a rotating heavy duty saddle which offers a rotating 360 degree handle for use at any angle. The design also offers 360 degree swivel casters and a lifting range from 5.6 inch to 13 inch.

• 360 degree swivel casters
• Safety overload system to prevent use beyond rated capacity
• Rotating heavy duty saddle
• Lifting range of 5.6 inch to 13 inch
• 360 degree handle for use at any angle
• 360 degree swivel casters
• Safety overload system to prevent use beyond rated capacity

User questions & answers

Question:	Will this lift a small suv like Jeep Compass
Answer:	I was able to lift my f150 with it no problems, I think you should be fine.
Question:	Where do i buy parts for it ? The small bracket that lifts the piston rusted and broke .Now it's useless
Answer:	You may as well just buy a new one and use your other one for parts. These are very cheap and cheaply made. My car folded on it the other day so I went and got a 50 dollar floor jack at harbor freight. Well worth it!
Question:	Description says 4-5 days, listing information says it ships in 1-2 months. Which is it
Answer:	It arrived within a day or two.
Question:	will it lift Nissan Altima
Answer:	Yes it can. All sedan type vehicle can be lifted by this particular jack. Except SUV’s, lifting height of this jack is not enough.

Product description

The Arcan jack is a sleek, low profile, durable, and long lasting 2T steel service jack capable of taking on any job for professionals or weekend warriors. The Arcan true low profile design allows users to get under almost any vehicle to lift and comes at a significantly lower cost compared to other models in the market. This model passes the 2009 ASME PALD standard, which is the industry's leading safety regulation for lifting equipment. Lift Capacity (tons) : 2

• COLORS MAY VARY: XL20 = A20015
• LOW PROFILE FRAME: For easy access under low ground clearance vehicles.
• DUAL PUMP PISTONS: Quickly raises the floor jack saddle to load.
• UNIVERSAL JOINT RELEASE MECHANISM: Provides precise control of jack.
• STEEL CONSTRUCTION: For heavy duty use.
• VEHICLE PROTECTION: Designed with a rubber saddle and a foam handle bumper.
• 2 PIECE HANDLE: Allows for easy storage.

User questions & answers

Question:	Does the handle need to be up to release the jack? In other words do you have to keep the outside of the jack handle clear from the car to lower it
Answer:	The handle does not need to be up to release the jack. The handle can be in any position to lower the car (turn handle counter clockwise to lower).
Question:	What are the wheels made of
Answer:	I'm no metal professional, but I believe they are made of steel. They are very thin but have not even succumbed to my terribly paved driveway yet. No dents, nothing. I've lifted my Z3 multiple times so far and no small rocks have caused any problems.I don't believe you have anything to worry about when it comes to the durability of the wheels.
Question:	what is the lift range of this jack
Answer:	The lift range is 3.5" to 18.1".
Question:	What is the dimension from the ground to the highest point on the jack body, e.g. the raised portion up near the jack handle
Answer:	The overall dimensions are 26"L X 13.2"W X 6.3"H. It has a lift range of 3.5" TO 18.1"H

Product description

This heavy duty 3 Ton car jack gets vehicles almost two feet off the ground. Extra-low profile reaches under most show cars. Dual piston Rapid Pump technology lifts most work loads in just 3-1/2 pumps.

• Super-tough precision welded construction with an industrial grade finish
• Industrial quality for professional mechanics and hardcore automotive enthusiasts
• Rapid Pump exclusive dual parallel pump system lifts with far fewer pumps
• Universal joint release provides precise load control in any handle position
• Extra-wide steel casters for stability

User questions & answers

Question:	Is this jack suitable to lift my motor to replace freeze plugs under the motor mounts
Answer:	The jack dose not stay up
Question:	What is the diameter of the saddle? Looking to get a rubber pad and need to know the size
Answer:	Outside diameter of the saddle pad is 4 1/4" .... There is a shoulder ( approximately 1/4" or more) to consider and inside diameter of it is 3 5/8" ... If I were putting a rubber pad on mine, I would stick with a 3 1/2" diameter... Another option, to maintain full pad diameter, would be to go with a 4 1/2" rubber pad and machine a surface just for that shoulder and the 4 dog ears that stand even a little taller. Good luck...
Question:	What is the maximum height when fully extended? In inches please. Thanks
Answer:	Maximum Lift Height (in.) 19-3/4 in.
Question:	Do i need to also purchase jack stands or will this do the job on its own
Answer:	YES. An automotive floor jack serves ONE PURPOSE: to elevate a vehicle TEMPORARILY to permit clearance for one or more floor jacks to support the vehicle. This floor jack does not come with stands. You must purchase a pair of floor jacks separately. Do not use this or any automotive floor jack to support a vehicle.

Product description

The Arcan ALJS3 3-Ton Steel Jack Stands has an overall 3-Ton lifting capacity and a working range of 11-5/8 in. to 17.5 in. A counterweighted pawl locks in place securely to prevent slipping, while allowing easy adjustments. A large contoured saddle with locating lugs helps support and position vehicle frame. The wide stance base delivers superior stability and includes base pads that prevents the jack from sinking into asphalt and provide stable footing for the jack stands. The welded construction and alloyed steel offer years of support. Arcan puts all of our lifting equipment through voluntary and rigorous third party safety testing, as outlined by the ASME PASE-2014 Safety Standard for Portable Automotive Service Equipment, to ensure that our products are among the safest on the market.

• COLORS MAY VARY: ALJ3T (silver) or A20018 (green)
• LIGHTWEIGHT AIRCRAFT-GRADE ALUMINUM: Allows for easy maneuverability.
• DUAL PUMP PISTONS: Quickly raises the floor jack saddle to load.
• REINFORCED LIFT ARM: Increases strength, chassis torsion control, and durability.
• VEHICLE PROTECTION: Designed with a rubber saddle and a foam handle bumper.
• SIDE-MOUNT HANDLE: Allows for convenient jack positioning.
• 2 PIECE HANDLE: Allows for easy storage.

User questions & answers

Question:	how smoothly and slow can a vehicle be lowered
Answer:	This fuel pressure reghulator is set at 43 PSI - identical to the OEM regulator. -Sean 818-574-FUEL
Question:	What is the height range
Answer:	Yes, this will fit the 2013-2018 Can-Am Maverick / Maverick Max 1000 . -Sean 818-574-FUEL
Question:	How big is the saddle and rubber pad on this jack
Answer:	This will be a 100% direct fit for the 2009-2018 Outlander 650. -Sean 818-574-FUEL
Question:	where is arcan made
Answer:	Yes, this will be a 100% direct fit for the 2013-2015 Can-Am Maverick 1000. -Sean 818-574-FUEL

Product description

The Torin BIG RED T82012 hydraulic trolley floor jack is constructed with heavy duty steel, providing long term durability with an industrial luster. This floor jack has a 2 ton (4,000 lb) capacity and features a minimum lifting height of 5-3/5" and a maximum height of 13", which is ideal for most cars, trucks, and SUVs. A safety bypass system prevents over-loading and ensures safe operation. Equipped with large steel casters and 360-degree swivel casters for smooth maneuverability. The Torin BIG RED T820014S hydraulic trolley floor jack is equipped with a handle for quick portability. It includes a plastic blow mold carrying case for easy storage when not in use. Includes a limited 1 year manufacturer warranty.

• Hydraulic trolley floor jack is constructed with heavy duty steel, providing long term durability with an industrial luster
• Features a 2 ton (4,000 lb) capacity with a minimum lifting height of 5-3/5" and a maximum height of 13"; Ideal for most cars, trucks, and SUVs
• Safety bypass system prevents over-loading and ensures safe operation
• Equipped with large steel casters and 360-degree swivel casters for smooth maneuverability
• Includes a plastic blow mold carrying case for easy storage when not in use; Includes a 1 year limited manufacturer warranty

User questions & answers

Question:	Will this work on a Chevrolet Denali
Answer:	NO, this car jack can't lift your Chevrolet Denali.
Question:	I have a 2001 ford escort zx2. Will this jack work for it
Answer:	Yes but you won't get enough height to change a tire unless you use a block. 2x4 works.
Question:	Can anyone tell me why this product "ships within 1 to 2 months" but is also Prime Eligible
Answer:	may be that this product is very heavy and if it comes through the post office mail and or Fed Ex, may have to passing through package security checks.......
Question:	can i use for a jeep gran cherooke
Answer:	I use mine on a 2011 Subaru Outback. I will lift one side of the vehicle for tire rotations. I use blocks under the suspension anyway,"just in case". The Jeep shouldn't weigh any more than my Outback...

Product features

Torin Big Red Hydraulic Trolley Floor Jack with Carrying Case, 2 Ton (4,000 lb) Capacity

• Constructed with heavy-duty steel, providing long term durability with an industrial luster
• Features a 2 ton (4,000 lb) capacity, a minimum lifting height of 5-3/5", and a maximum height of 13"
• Safety bypass system prevents over-loading and ensures safe operation
• Equipped with large steel casters and 360-degree swivel casters for smooth maneuverability
• Includes a plastic blow mold carrying case for easy storage when not in use

Unique Saddle Design

360-Degree Rotating Handle

360-Degree Swivel Casters

Carrying Handle

Product description

The Torin TCE TCET825051 hydraulic trolley floor jack is constructed with heavy duty steel, providing long term durability with an industrial luster. This floor jack has a 2.5 ton (5,000 lb) capacity and features a minimum lifting height of 3-3/8" and a maximum height of 14-15/16", which is ideal for most cars, trucks, and SUVs. A safety bypass system prevents over-loading and ensures safe operation. Equipped with large steel casters and 360-degree swivel casters for smooth maneuverability. A built-in carrying handle allows the floor jack to be lifted quickly for ultimate portability. Includes a limited 2 year manufacturer warranty.

• Hydraulic trolley floor jack is constructed with heavy duty steel, providing long term durability with an industrial luster
• Features a 2.5 ton (5,000 lb) capacity with a minimum lifting height of 3-3/8" and a maximum height of 14-15/16"
• Ideal for most cars, trucks, and SUVs; Safety bypass system prevents over-loading and ensures safe operation
• Equipped with large steel casters and 360-degree swivel casters for smooth maneuverability
• Built-in carrying handle allows for the jack to be lifted quickly; Includes a limited 1 year manufacturer warranty

User questions & answers

Question:	Does this jack has a 2yr warranty or 1yr warranty, in one area of the description it says 2 and in another area it says
Answer:	This jack is 2 year warranty.
Question:	Is this floor jack made in China
Answer:	Yes, mine was.
Question:	I need to raise a shed. Could I use this jack to lift it at the corners
Answer:	It depends on the weight of your shed and the height you need to lift，If your shed weighs less than 4000 lbs and the max lift height is less than 14-15/16", it can be used.
Question:	does it come with a case
Answer:	A case? You mean something to store it in? If this is what you mean, then NO it does not come with a case, but it does have a handy carrying handle.

Product description

The Torin TAM815016L racing floor jack can be used for general or specialty use and features a 1.5 ton (3,000 lb) capacity. With a lift range between 3-1/2" to 14-1/8", you can gain easy access under low-profile vehicles. It's constructed of durable, high-strength aluminum. Equipped with a dual piston quick lift pump, allowing you to easily raise the jack to the desired height. A foam bumper on the handle helps protect your vehicle from damage. A convenient side handle makes it easy to carry. In terms of safety, this Torin service jack even comes with a built-in safety overload system which prevents use beyond load capacity. Includes a limited 1 year manufacturer warranty. Aluminum two-piece long handle with knurled hand grip. Rubber padded saddle protects vehicle frame.

• Racing floor jack can be used for general or specialty use and features a 1.5 ton (3,000 lb) capacity
• Constructed of durable, high-strength aluminum and steel; Equipped with a dual piston quick lift pump, allowing you to easily raise the jack to the desired height
• Lifting range from 3-1/2" to 14-1/8" allows you can gain easy access under low-profile vehicles
• Foam bumper on the handle helps protect your vehicle from damage; Convenient side handle makes it easy to carry
• Features a built-in safety overload system prevents use beyond load capacity; Includes a limited 1 year manufacturer warranty

User questions & answers

Question:	How much does it weight
Answer:	NO, I think this car jack can't lift your car, the chassis's height of your car is higher than the max lifting height of the jack.
Question:	Hi,... I am searching for parts for the above item. Handle, and swivel joint that connects the handle to the valve. Please advise if you are able t
Answer:	No. The blade is not strong enough for 3/4” hard wood.
Question:	Where is this made
Answer:	Absolutely. This laminate cutter will have no problem cutting 8mm Vynal. Thanks for the question!
Question:	Can this lift a 2020 chevrolet traverse to change a tire
Answer:	We bought this to do Luxury Vinyl tiles they were 7x48" and a 20mil thickness... I know this isnt the same material your using but, this cutter was awesome! Highly recommend it, saved a lot of time being able to keep right next to us.

Product features

Torin Hydraulic Low Profile Aluminum Floor Jack with Dual Piston Quick Lift Pump, 1.5 Ton (3,000 lb) Capacity, Black

• Racing floor jack can be used for general or specialty use and features a 1.5 ton (3,000 lb) capacity
• Lifting range between 3-1/2" to 14-1/8" allows you to gain easy access under low-profile vehicles, making the placement on the undercarriage of any vehicle is easy
• Constructed of durable, high-strength aluminum
• Equipped with a dual piston quick lift pump, allowing you to easily pump the jack to the desired height
• Foam bumper on the handle helps prevent against vehicle damage while in use

Product description

The Torin TORT825051 hydraulic trolley floor jack is constructed with heavy duty steel, providing long term durability with an industrial luster. This floor jack has a 2.5 ton (5,000 lb) capacity and features a minimum lifting height of 3-3/8" and a maximum height of 14-15/16", which is ideal for most cars, trucks, and SUVs. A safety bypass system prevents over-loading and ensures safe operation. Equipped with large steel casters and 360-degree swivel casters for smooth maneuverability. A built-in carrying handle allows the floor jack to be lifted quickly for ultimate portability. Includes a limited 1 year manufacturer warranty.

• Hydraulic trolley floor jack is constructed with heavy duty steel, providing long term durability with an industrial luster
• Features a 2.5 ton (5,000 lb) capacity with a minimum lifting height of 3-3/8" and a maximum height of 14-15/16"
• Ideal for most cars, trucks, and SUVs; Safety bypass system prevents over-loading and ensures safe operation
• Equipped with large steel casters and 360-degree swivel casters for smooth maneuverability
• Built-in carrying handle allows for the jack to be lifted quickly; Includes a limited 1 year manufacturer warranty

User questions & answers

Question:	Does this jack have a saddle hole
Answer:	No it doesn't...
Question:	the specs for this item says it weighs 10.38 lbs. Can you confirm
Answer:	No, it’s incorrect the net weight of the jack is about 25.1 lbs ,the gross weight of the jack is about 26.4 lbs.
Question:	How big is the plate (or the jack pad holder
Answer:	The diameter of the pad is 2.36“.