14 best toyota car diagnostic tools

• Classic design, fast scan and clear trouble codes, even a beginner can use this unit to read the error code, find out what the problem is and perhaps fix it. Save money and time.
• Works on MOST 1996 US-Based, 2000 EU-Based and Asian cars, and newer OBD II & CAN domestic or import vehicles. Supports English, German, French, Spanish, Finnish, Dutch, Russian and Portuguese.
• Easily determines the cause of the check engine light. I/M monitor readiness test, turn off the MIL (check engine light) as well as view freeze frame data. Read hard (memory) / pending (intermittent) and historic codes and show definitions.
• The AD310 scanner is well built with a large LCD display (128 x 64 pixel) that has white backlight and contrast adjustment, indicates test results directly. No need any Batteries or Charger, gets the power directly from the OBDII Data Link Connector in your vehicle.
• It's equipped with a 2. 5 feet long cable and made of a very thick flexible insulator. There are 4 buttons on AD310. The Up and Down button for scrolling the menu, the Enter and Exit button allow for navigation back and entering menu.

Product features

Key Features

Code Definition

• TURN OFF CHECK ENGINE LIGHT: Autel MS309 OBDII scanner is an easy-to-use plug-n-play check engine code reader that read and clear codes. This little code scanner retrieves generic (P0, P2, P3, and U0), manufacturer specific (P1, P3, and U1) codes, and pending codes and displays DTC definitions on the TFT color screen. It can check engine related fault codes, easily find out what caused the check engine light comes on, turn off MIL light(Malfunction Indicator Light).
• FREEZE FRAME DATA FOR ACCURATE DIAGNOSIS: This MS309 check engine code reader comes with viewing freeze frame function that enables you to retrieve data recorded in the ECU of the condition under which the fault occurs to figure out why the check engine light is on and cut down test drive cycle verification time. It includes important engine parameters such as RPM, vehicle speed, mass airflow, engine load, fuel pressure, short/long term fuel trim, engine coolant temperature and etc.
• READINESS STATUS TO PASS SMOG CHECK: The Autel MS309 car diagnostic scanner tool comes with I/M Readiness function to check the operations of the Emission System on OBD2 compliant vehicles. It includes vehicle-specific number of monitors like misfire monitor, fuel system monitor, comprehensive components monitor, O2 sensors, EVAP system and etc, making this OBD2 scan tool an excellent scan tool to help get your vehicle ready to pass the annual smog check.
• UNMATCHED COMPATIBILITY: Autel MS309 compact pocket code reader supports all OBD2 protocols: KWP2000, ISO2000, ISO9141, J1850 VPW, J1850 PWM and CAN. This OBD2 code scanner is compatible with all OBDII-Compliant vehicles, passenger cars or light trucks, post 1996 in US, post 2000 for EU-based and Asian cars.
• RETRIEVE VEHICLE INFO: The Autel MS309 automotive OBD2 scanner enables retrieval of the Vehicle Identification No. (VIN), Calibration ID(s), Calibration Verification Nos. (CVNs). This function is most useful to check whether the ECU matches your car when you are buying a used car. The MS309 auto car scanner comes with LIFETIME FREE software updates and is backed by 45 Day Money Back and 12 Months US Seller . Purchase now and go fix something!

User questions & answers

Question:	will this work on my 2000 Toyota Prado dieselwith 1KZ engine
Answer:	Hi there, I am with BAFX Products. Sadly it will not read any ABS/SRS?VSC or any other codes. The only codes it is able to read are those which cause your vehicles "check engine" light to illuminate. Any other lights require more specialized tools for reading. Best regards, BAFX Products
Question:	Will this work on a Nissan X trail T
Answer:	yes, I'm using Windows Phone 8 on Nokia 920 with OBDAutoDoctor application. You need to connect the PIC18F2480 via Bluetooth, before starting an OBD2 scan tool application. On Windows Phone 8 only a few OBD2 app are available. OBDAutoDoctor is free but get only some information from the car. I just found how to unlock the pro version...It's a in-app purchase...click "..." at the bottom of the app to upgrade. The Pro version is available for $7.99.
Question:	i used this tool and all is said was manufacturer control. no code number with it? what does that mean? 1998 ford explorer sport
Answer:	Hi Christopher - I am with BAFX Products Support.In MOST vehicles you will be ok leaving the adapter plugged in as long as the vehicle is driven every few days. However we make the following recommendations:1) Do not leave the adapter plugged in if it will not be driven for 24-48 hours2) If your area is to be experiencing extreme cold unplug the adapter as the combination of cold and the adapter will drain it faster3) If your battery is more than a 1-2 years old you will want to be very careful about leaving it plugged in, older batteries do not hold the same juice as the newer ones4) If you have an electronics heavy vehicle such as BMWs tend to be we do not recommend leaving it plugged in as the vehicles electronics do not always fully power down either5) If you have any other device plugged into the vehicle while it is off via cigarette ports or whatever we then also recommend removing the adapterI hope that these tips and information are found helpful. If you have any further questions you may always reach out to us through the Amazon messaging system at any time!Best regards,BAFX Products Support
Question:	Can you use this to diagnosis why check engine light is on and figure out why car wont start? even of car wont start
Answer:	I can confirm that this adapter WILL read (I haven't tried to clear yet) ABS codes on Ford (2001 Ranger 4.0L), using FordSysFree or MotorDataOBD Free (both Android). ABS codes are in the Cxxxx range. Mine picked up, correctly, C0034 - Front Right Wheel Speed Sensor Failure. While other adapters may be able to read these codes with other Android Apps, this ELM327 BAFX adapter does capture ABS codes for Ford. That is the only one I can confirm. Yes, FORScan for PC should also pick up these codes with this adapter. I have not tested Torque PRO, but I don't believe it will read ABS codes with this adapter.

Product features

MaxiScan MS309

Quickly scan and define vehicle Diagnostic Trouble Codes (DTCs) with this easy-to-use, compact code reader with the ability to view Freeze Frame Data, check I/M Readiness (Emissions) and monitor status. The MS309 is a go-to tool for quick vehicle health status.

View Freeze Frame

The Autel MS309 auto code reader is most useful while diagnosing continuous monitor faults like engine misfire and fuel control concerns.

When an emissions related fault occurs, the OBD II system not only sets a code but also records a snapshot of the vehicle operating parameters to help in identifying the problem. This set of values is referred to as Freeze Frame Data and may include important engine parameters such as engine RPM, vehicle speed, mass airflow, engine load, fuel pressure, fuel trim value, engine coolant temperature, ignition timing advance, or closed loop status.

Smog Check

MS309 engine scanner code reader comes with I/M readiness status check function that shows you whether all the emission related systems and components are operating within allowable limits to help you pass the annual Smog Check.

The engine scanner shows readiness status with series of readiness monitors: continuous monitors like misfire, fuel system and comprehensive components monitor and non-continuous monitors like EGR system, O2 sensors, Catalyst, Evaporative System, O2 Sensor Heater, Secondary air, Heated Catalyst and A/C system.

DTC Definitions

Autel MS309 supprots DTC definitions. The definitons will be displayed bellow the codes. It provides you an easier way to read and a quick understanding of what's the meaning of the fault codes that was detected.No need to search online for what's the codes meaning.

Retrieve Vehicle Information

MS309 automotive scanner retrieves the Vehicle Identification No. (VIN), Calibration ID(s), Calibration Verification Nos. (CVNs). This function is especially useful while you take this little pocket OBD2 code reader with you while buying a used car to check whether the VIN matches and make sure the ECU has not been replaced with a garbage car.

Turn Off Check Engine Light & Erase Codes

Autel MS309 scanner not only read and clear normal codes, but also retrieves generic (P0, P2, P3 and U0), manufacturer-specific (P1, P3 and U1), and pending codes

Vehicle Coverage

Autel MS309 car OBD2 scanner is Compatible with domestic, Asian and European vehicles, 1996 and newer. And the auto scanner supports all 5 OBDII protocols: KWP2000, ISO2000, ISO9141, J1850 VPW, J1850 PWM and CAN.

Product description

Retrieve generic and manufacturer specific diagnostic trouble codes(DTC), clear codes and turn off check engine light. Follow the correct order to use the OBD2 scanner: Engine off- Plug it in- Turn ignition on.

• TURN OFF CHECK ENGINE LIGHT: MS300 check engine code reader can read, clear generic, manufacturer-specific and pending codes. It enables you to figure out why CEL is on like a pro and turn off check engine light instantly after proper repair.
• MECHANIC APPROVED: MS300 OBD2 scanner works with most OBDII compliant(OBD2 protocols: KWP2000, ISO2000, ISO9141, J1850 VPW, J1850 PWM, and CAN) sedans, SUVs and light trucks post-1996 for US cars, post-2000 for EU-based and Asian cars.
• DIAGNOSE IN SECONDS: MS300 auto code reader features easy to use 2 button design to read, clear DTCs to help home mechanics locate car problems fast. With an intuitive interface and easy-to-read backlit screen, this diagnostic code reader is easy to use.
• SMOG CHECK: MS300 car code reader retrieves I/M Readiness status to check emission-related systems like misfire monitor, fuel system monitor, comprehensive components monitor, O2 sensors, EVAP to help your vehicle ready pass the annual smog check.
• NO BATTERY NEEDED: MS300 OBDII scan tool communicates with vehicles through standard 16-PIN OBD2 cable and it’s powered by vehicle directly- no battery needed. Please follow the correct usage order: Engine off- Plug MS300 in- Turn Ignition On.
• RETRIEVE VIN NUMBER: MS300 engine code readers can retrieve VIN (Vehicle Identification Number) on 2002 and newer vehicles supporting Mode 9 for quick vehicle identification and cut time spent locating the cause why the check engine light is on.
• Retrieves generic and manufacturer specific Diagnostic Trouble Codes (DTC), includes definitions lookup software on CD and displays DTC definitions on screen

Product features

Autel MaxiScan MS300 OBD2 Scanner Code Reader Turn Off Check Engine Light Smog Check

AUTEL STORY

Autel is one of the major manufacturers of professional diagnostic tools, equipment and accessories in the automotive aftermarket. Autel, with automotive experts of years of experiences in the industry, has been committed to creating maximum value to customer worldwide by providing quality-assured, user-friendly, cost-effective and innovative products since its foundation more than 15 years ago.

Autel MaxiScan MS300

The MaxiScan MS300 code reader supports all OBDII protocols, including KWP2000, ISO2000, ISO9141, J1850 VPW, J1850 PWM and CAN. Though small in size, the MS300 is able to retrieve the same emission related information as large expensive scanners. MS300 works with most post 1996 vehicles that are OBDII compliant (including CAN).

• Read and clear your Check Engine Light and all other vehicle systems. Get your unlimited free vehicle specific Repair Reports, generated from our database of millions of fixes verified by Professional Automotive Technicians
• As easy to use as a code reader with all the capabilities of an expensive handheld scan tool, plus the benefits of your smartphone or tablet (free app updates, portability, saving data, interactive graphing of live data)
• Officially licensed and certified for Apple and Android devices
• The BlueDriver App and BlueDriver Sensor work exclusively with each other to ensure quality
• BlueDriver is the Professional OBD2 Diagnostic Scan Tool trusted by mechanics and developed by Professional Engineers in North America

User questions & answers

Question:	Will the device display "short term and long term" fuel trim data
Answer:	Thank you for your question. This tool will have free future updates, but cannot be guaranteed for life. This tool was just released less than a year ago so tool is already up to date. The next available update will be sometime next year. The updates will always be free.
Question:	Will is run a abs bleeder test
Answer:	Thank you for your question. The 3160RS never needs to be charged so no charging cable is required. The 3160RS and all of our code readers link to a vehicle through that vehicle's 10-15 amp accessory fuses. If any of the vehicles accessory fuses are blown, tool will not link to vehicle. Batteries for this tool are not needed as well. Batteries are optional and are only used to pair tool to Bluetooth/Wifi without being linked to vehicle, and to look at stored information in tool if not connected to vehicle.
Question:	so the device is 100 and u have to buy more apps
Answer:	Thank you for your question. Yes, there is a light at the end of the DLC cable plug.
Question:	Do you only hook up to it when check engine is on or it stays plugged in
Answer:	Thank you for your question. The 3160RS will support TPMS, steering angle reset, EPB, ABS brake bleeding, transmission temperature, oil level, oil life, and brake pad life for most 1996 and newer vehicles. The 3160G doesn't offer any of these features. The 3160RS just came out less than a year ago and will have free, future updates. The 3160G has been out for almost 5 years now. The 3160RS uses are RS2 app which is only compatible with a smart phone or tablet. The 3160G uses our original RS software which is compatible on a computer, laptop, or smart phone.

Product features

The Right Fix. Always.

BlueDriver will match your vehicle's make, model, and trouble code to a specific fix from a database of millions of repairs. Your Repair Report will always contain fixes that have been verified by ASE Certified Technicians, so no more googling unreliable fixes that waste your time and money.

The BlueDriver Sensor, paired with the free BlueDriver App (iOS or Android), gives you a complete vehicle repair solution. No other scan tool or code reader offers this level of insight into how to fix your vehicle.

BlueDriver Offers More. Period.

BlueDriver reads (and clears) all the codes the other guys read and the ones they don't. BlueDriver's Enhanced Diagnostics give you complete access to information normally only accessible to professional mechanics on their most expensive scan tools.

What are ENHANCED diagnostics?

All vehicles with an OBD2 port are required to output basic information when the Check Engine Light comes on. However, a lot of important information (such as ABS, Airbag, Climate Control, etc.) is left behind by other scan tools and code readers. Only BlueDriver gives you the complete set of diagnostics on a wide range of manufacturers.

Get Enhanced Diagnostics On:

• NOT COMPATIBLE WITH iOS DEVICES - (iPhones, iPads etc); OUR BLUETOOTH OBD2 scanner IS ONLY COMPATIBLE WITH ANDROID OR WINDOWS DEVICES; For iOS devices, see our WiFi OBD Reader
• READ & RESET - Our OBD2 diagnostic scanner tool will work on all cars purchased in the USA model year 1996 or newer; Unlike other OBD2 scanners, ours works on ALL OBD2 protocols including J1850 and CAN; With our scan tool you can read & reset the check engine light on your car with ease
• REAL TIME - Monitor the diagnostic sensors in your vehicle in real time for things like O2 data, fuel pressure, EVAP system & more; Car reporting an EVAP code? Check your O2 readings to see which sensor is faulty and get it fixed; React quickly to problems like a professional mechanic
• HUGE APP SELECTION - 3rd party app must be downloaded to use; Choose from many OBDII apps such as Torque Pro, Piston, Dash Command, OBD Fusion & more; Some OBDII readers limit you in which apps you can use, not BAFX Products; Choose an app at a price that meets your needs
• This OBD2 scanner does not read ABS, SRS, TPMS or Oil Change lights; WARRANTY - 2 Year manufacturer warranty with USA based friendly support staff; Don't be left stranded by support

User questions & answers

Question:	Will it read ABS codes
Answer:	I do not know...if you have a security light flashing I would go to an Auto Zone they will do a free scan to tell you what is wrong with it and if it can be fixed or you may have to go to a dealership to have it fixed ....
Question:	Does this work with Windows Phone
Answer:	The Maxiscan MS300 is also an Autel product. It is a legacy product that has been superseded by the Autel AutoLink AL301¹. As is customary for these entry-level devices, it only reads / reports the generic OBD II codes. To move up to manufacturer specific codes one must move up to the Autel AutoLink AL319². Keep in mind that not ALL manufacturer specific codes are possible to read / report on. Some are kept secret by the vehicle manufacturer to ensure the dealer techs get a shot at your wallet once in a while. ^_^¹ http://www.auteltech.com/autelcms/Code%20Readers&Code%20Scanners/357.jhtml² http://www.auteltech.com/autelcms/Code%20Readers&Code%20Scanners/358.jhtml
Question:	can i leave it plugged in
Answer:	Yes.It has an I/M Readiness mode that is able to show you the details of the readiness of each major emission monitor. There is even a button on the device that can select this directly without having to navigate through the menus.There is also a lamp on the device that indicates if any emission monitor is not ready.It is my understanding that the requirements for I/M readiness for each vehicle may differ from state to state.I had a problem with an air monitor coming ready after I identified, resolved, and cleared the underlying code. It took miles of specific type of driving to clear this monitor status (which cannot be cleared by the device.)When I returned to the inspection station I was informed that all monitors are not required to be ready to pass New York state inspection, and that my extra driving for this situation was unnecessary.
Question:	does it pick up abs codes
Answer:	It gives a text explanation of the code (eg. Nissan code P1135 = 'Intake Valve Timing Control Bank 2'). Beyond that, you're having to look online or in service manuals to determine what the message actually means and how to resolve it.

Product features

Quickly Diagnose and Analyze Car Problems

Warning lights flashing up like an airport runway? Tear your eyes from that depressing dashboard and connect your BAFX Products Diagnostic Car Scanner & Reader Tool.

See what the issue with your car is within moments, and depending on your model you can -

•Read and clear your ‘Check Engine' light

•Identify those annoying car troubles before they become serious

•Get readings on your emissions to ensure you’ll pass any tests

•Check you air/fuel ratio •Confirm your O2 sensors are working properly

•Obtain info on a variety of other car readings

Reliable and Consistent

It’s no secret that many diagnostic car scanners on the market aren’t very dependable.

Either they only work on a limited number of car models, don’t pick up on important issues, or simply suffer from bad connectivity which makes them inconsistent and difficult to use.

At BAFX Products we’ve made it our mission to bring you a diagnostic scanner with solid Bluetooth connectivity that works on the broadest range of car models.

Put simply, at this cost it cannot be beat.

Works on Most Car Models After 1996

While most competitor’s products only work on a limited selection of vehicles, ours works across a broader range of protocols.

The result is that ours are far more likely to work on your car. And your wife’s car. And your friends’ cars…

Android and Windows Compatible

Who says iOS users get to have all the fun?

This product is specially constructed to work exclusively with Android and Windows devices,

Simply install a suitable third-party app (we recommend ‘Torque Pro’) and get to work!

Can Be Used Internationally

Think this diagnostic scanner can only be used in the good old US of A?

Think again, because it can be put to use on a wide selection of cars in a broad range of countries.

If you want to know if it will work on your car model and in your country then simply send us a message to find out.

• Bluetooth OBD2 adapter with support for extensive third-party apps (such as OBD Fusion, Torque Pro, Car Scanner ELM OBD2) can turn your iPhone, iPad or Android phone/tablet into a sophisticated car scan tool.
• Read diagnostic trouble codes and freeze frame data, reset check engine light, prepare smog test, view real-time sensor readings, create customized dashboard and estimate fuel economy.
• Works with OBD2 / EOBD compliant cars and light trucks (year 1996 or newer in the US, including pickup trucks, hybrid and many electric vehicles; may require special apps).
• Compatible with iOS (no Bluetooth pairing needed; connect in the app) & Android devices (head units not recommended). Easy to plug in and unplug. No complex settings or tricky connections plus much lower power consumption compared to WiFi, and it does not block internet access for other apps.
• A third-party App is required (check recommendations in the description below, some may require separate purchase). Comes with one-year replacement warranty.

Product features

Check why the Check Engine Light is on

The OBDCheck BLE helps you read the error codes causing the check engine light to come on. You may then find out what the possible causes are and fix simple problems by yourself and reset the light, potentially saving you a trip to a garage and hundreds of dollars. When you need to bring your car to a mechanic, it also gives you a peace of mind.

Powerful scan tool and more

With the proper app, you can do more:

· View real-time sensor readings,

· Monitor fuel economy,

· Create your own dashboard,

· Know whether your vehicle is ready for smog check,

· On specific vehicles, you can even have advanced features like enhanced PIDs, diagnostics and coding (requires capable App),

· And more to discover!

Universal Vehicle Compatibility

Works with 1996 and newer cars, SUVs, MPVs, mini vans and light trucks sold in the United States. Vehicles in other regions may also be supported:

Australia – 2006 (gas), 2007 (diesel)

Brazil – 2007 (gas)

Canada – 1998

European Union – 2001 (gas), 2004 (diesel)

Mexico – 2006, etc.

Specifications

Communication Method: Bluetooth LE for iOS, Classic Bluetooth for Android & Windows

Supported Devices: iOS with Bluetooth 4.0 or above, Android phone & tablet (Android car radios/head units may not be compatible), Windows, Mac

Operating Voltage: 9V~16V

Operating Current: Max 45mA

Operating Temperature: -40~185°F (-40~85°C)

Dimension: 1.61" x 1.97" x 0.87"

Package Includes:

1 x Veepeak OBDCheck BLE OBD2 Scanner

1 x Storage Pouch

1 x User Manual

• HIGH COMPATIBILITY: Does it fit your car? This Bluetooth cost-effective OBD2 scanner works on almost 1996 and newer OBDII-compliant vehicles. If there are any adaptability issues, please provide the model, VIN, etc. to [email protected] or Q&A.
• DIVERSE CHOICES: Want more options? This Autel AP200 APP is suitable for iPhone & Android, which can be lifetime free downloaded. It offers one FREE model and is available to buy extra models if needed ($21. 99 iOS / Android per model).
• POWERFUL FUNCTIONS: Where are our advantages? This Autel scanner is different from other OBD2 scanners. It not only is not limited to OBD2 functions but performs more functions such as accessing all available systems and common reset services.
• STABLE CONNECTION: Want to diagnose outside of the car? The BT4.2 connectivity makes this OBD2 scanner to be stable and easy to use. If there is a problem with the connection, welcome to contact us and the problem will be solved within 24 hours.
• HASSLE-FREE PURCHASE: Worry about quality? Autel AP200 offers 12-month warranty to against material and manufacturing defects. The lifelong free update ensures faster and more accurate diagnosis than before. NOTE: AP200 does not support tablet devices.

User questions & answers

Question:	for how long the purchase of additional licenses is good ,I see has and expiration date
Answer:	Hello, the first car make you register is life time free. And we kindly suggest purchasing only 1 year for additional car makes duo to you can re-purchase after it has expired. Any further question, feel free to contact us.
Question:	When buying additional vehicle diagnostic, Does vehicle specific software mean make e.g toyota or toyota highlander
Answer:	Hello, vehicle specific software means vehicle make, ie, Toyota, including toyota highlander and other models of Toyota. Any further question, feel free to contact us.
Question:	If i buy an additional car upgrade for my ap200, does it work with both my android and iphone, or do i have to buy it twice (once for each platform
Answer:	Hello, No need to buy it twice, it will work with both your android and iphone phones. Any further question, feel free to contact us.
Question:	Which is better to buy, bluedriver or ap200, what is the difference between them
Answer:	Hello, we would recommend AP200 to you. Autel AP200 is new released bluetooth obd2 scanner with OLS/EPB/BMS/SAS/TPMS/DPF and IMMO etc at a compative price. Any further question, feel free to contact us.

Product features

25 Service Functions

Oil Light Reset

Inject Coding

Throttle Learning

ABS Bleeding

EPB Service

BMS (Battery Registration)

TPMS Reset

Gear Learning

And much more …

• 🍀【A FREE PROTECTION CASE for U】: There is a main unit with OBD 16PIN diagnostic cable, user’s manual -- Instructions on Tool Operations, USB Cable -- Connect to a Computer for Upgrading Online and ►one FREE Protection Case for you. As usual, on the OBD market, you sholud pay for the Protection Case, but in our store, you can get it free.
• 🍀【OBD/EOBD 2 Modules in 1】: Full 10 modes OBD2 diagnostic functions: read and erase fault codes, view I/M readiness, data stream, freeze frame data, retrieve auto vehicle information, O2 Sensor test to accurately locate bad O2 sensor, advanced onboard monitoring, and the EVAP test function which enable you initiate a leak test for the vehicle’s EVAP system.
• 🍀【Realtime Live Data in Graph】: NEXAS NL101 car obd2 scanner helps you to check the car engine fault codes, displays the error code definition, finds out what caused and the result of the check engine light on, turn-off Malfunction Indicator Lamp (MIL), provides you the solution methods and reduce/avoid maintenance costs. Show real-time live data in graph to diagnose your vehicle. Save Time and Money.
• 🍀【Rare Unique Battery Check】: The NL101 car code reader can read real-time battery voltage, monitor car battery health status, and give out 6 warning tips for your to maintain your battery. It offers such useful information for entry-level Pros and DIYer that they can quickly and efficiently troubleshoot OBD2/EOBD problems on vehicles, meantime also watches out the battery power situation.
• 🍀【"?" Help & DTC Lookup & I/M】: NEXAS NL101 can help you explain the "?" on All Live Data, Freeze Frame and etc. when you don't know the meaning of the diagnosis. And you can go to the DTC Lookup to find the error codes when you don't know the meanings of them. You can one-click the I/M Monitor to perform emission readiness status, indicate whether various systems related to emissions on the vehicle are operating normally, and are ready for inspection and maintenance testing.
• 🍀【Multi-Languages & Vehicles】: English, Spanish, French, Deutsch, Italian, Russian, Portuguese, Finnish etc. Works on all cars, mini vans and light duty vehicles (OBDII & CAN) from 1996 and latest – American cars released from 1996 years, European cars released from 2000 years and Asian cars released from 2006 years. 🚩Especially Japanese cars released from 2006 years.
• 🍀【Long Press the "ESC" Key】: When you wanna exit the interface, LONG PRESS the "ESC" key, remember, LONG PRESS, not press once, or press twice in succession. 🚩Before using our product, you can use it directly without updating the software.
• 🍀【Adjust the Screen Brightness】: It’s normal that the screen can’t be seen clearly because of reflection problems outdoors. The same happens when we use mobile phones outdoors. Just adjust the screen brightness of the OBD2 scanner to the maximum.

Product features

NEXAS NL101 OBD2 Scanner Check Engine Light Car Code Reader Automotive Diagnostic Tool Fault Code Scanner, Car Check Engine

The NEXAS NL101 is specially developed for car, min van and light vehicles, which supports all 10 modes of OBDII test (EVAP, O2 Sensor, I/M Readiness, MIL Status, VIN Info, and On-board monitors testing etc.) for a complete diagnosis and enables users to read DTCs, clear DTCs and view the live engine data stream with a live color graphing. It covers a wide range of vehicles since it offers multiple data bus protocols, such as CAN, J1850 PWM, J1850 VPW, ISO9141 and KWP2000.

NL101 obd2 scanner works on all cars, mini vans and light duty vehicles (OBDII & CAN) from 1996 and latest:

1. American cars released from 1996 years
2. European cars released from 2000 years
3. Asian cars released from 2006 years, Especially Japanese cars released from 2006 years.

As an unique feature while other OBD scanner dose not have, NL101 could quickly check the vehicle’s battery health, read out the current battery value and give out 6 levels of battery warnings for your knowledge. It can be connected to PC through the USB cable for upgrade to keep updated with the latest software version.

Notice: NL101 may automatically reset while being disturbed by strong static electricity. THIS IS A NORMAL REACTION.

Top Reasons to Choose NL101:

1. OBD/EOBD 2 modules in 1.
2. Live data show in Graph, the data are straightforward to know.
3. Battery check, it is seldom to have in the same product.
4. Multi-Languages, English, Spanish, French, Deutsch, Italian, Russian, Portuguese, Finnish etc.
5. A F-REE Protection Case for U, you don't need to pay for it, but most products on the market need to, that is the other product doesn't have.

OBD II Modes of Operation:

Here is a basic introduction to the OBD II communication protocol. Mode byte: The first byte in the stream is the mode number. There are 10 modes for diagnostic requests. The first byte in the response data bytes is this same number plus 64. For example, a mode 1 request would have the first data byte = 1, and the response would have the first data byte = 65. Here is a brief description of the modes:

• Mode 01 – Identifies the Powertrain information and shows current data available to the scan tool. This data includes: DTC set, status of on-board tests, and vehicle data such as engine RPM, temperatures, ignition advance, speed, air flow rates, and closed loop status for fuel system.
• Mode 02 – Displays Freeze Frame data. Same data as in mode 1,but it was captured and stored when a malfunction occurred and a DTC was set. Some of the PIDs for mode one are not implemented in this mode.
• Mode 03 – Displays the type of powertrain or emission related DTCs stored by a 5 digit code identifying the faults. There may be more than one response message if there are more trouble codes than will fit in the data bytes of the response message, or if there are more than one ECU computer responding.
• Mode 04 – Used to clear DTCs and Freeze Frame data. This clears all diagnostic trouble codes that may be set including freeze frame data and readiness monitors.
• Mode 05 – Displays oxygen sensor test results. This mode displays the oxygen sensor monitor screen and the test results gathered about the oxygen sensor. There are ten numbers available for diagnostics: 01) Rich-to-Lean O2 sensor threshold voltage. 02) Lean-to-Rich O2 sensor threshold voltage. 03) Low sensor voltage threshold for switch time measurement. 04) High sensor voltage threshold for switch time measurement. 05) Rich-to-Lean switch time in ms. 06) Lean-to-Rich switch time in ms. 07) Minimum voltage for test. 08) Maximum voltage for test. 09) Time between voltage transitions in ms.
• Mode 06 – Non-continuously Monitored Systems test results.There are typically a minimum value, a maximum value, and a current value for each non-continuous monitor. This data is optional, and it is defined by a given vehicle maker if it’s used.
• Mode 07 – A request for DTCs (pending) from Continuously Monitored Systems after a single driving cycle has been performed to determine if repair has fixed a problem. This is used by service technicians to verify repair was performed properly and after clearing diagnostic trouble codes.
• Mode 08 – This special Control Mode requests control of the on-board system, test, or component bi-directionally (where applicable). This mode is manufacturer specific.
• Mode 09 – Reports vehicle information. This information includes vehicle VIN number and calibration information stored in the vehicle ECUs.
• Mode 0A – Requests Emission-Related Diagnostic Trouble Codes with Permanent Status. This mode is required for all emissions-related DTCs.The presence of permanent DTCs at an inspection without the MIL illuminated is an indication that a proper repair was not verified by the on-board monitoring system.

NEXAS NL101 OBD2 Automotive Scanner Engine EVAP Battery OBDII Scanner PK CR3001 ELM327 Professional EOBD OBD Car Diagnostic Tool

When more than one vehicle control module is detected by the scan tool, you will be prompted to select the module where the data may be retrieved. The most often to be selected are the Power train Control Module [PCM] and Transmission Control Module [TCM].

CAUTION: Don’t connect or disconnect any test equipment with ignition on or engine running.

1. Turn the ignition off.
2. Locate the vehicle’s 16-pin Data Link Connector (DLC).
3. Plug the scan tool cable connector into the vehicle’s DLC.
4. Turn the ignition on. Engine can be off or running.
5. Turn on the scan tool. Use the "UP/DOWN" scroll button to select OBDII/EOBD from the Main Screen.
6. Press the "OK" button to wait for the Menu to appear. A sequence of messages displaying the OBDII protocols will be observed on the display until the vehicle protocol is detected.
7. View a summary of system status (MIL status, DTC counts, Monitor status) on screen. Press [OK]

If the scan tool fails to communicate with the vehicle’s ECU (Engine Control Unit) more than three times, a “LINKING ERROR!” message shows up on the display.

• Verify that the ignition is ON;
• Check if the scan tool’s OBD II connector is securely connected to the vehicle’s DLC;
• Verify that the vehicle is OBD II compliant;
• Turn the ignition off and wait for about 10 seconds. Turn the ignition back to on and repeat the procedure.

If the “LINKING ERROR” message does not go away, then there might be problems for the scan tool to communicate with the vehicle. Contact your local distributor or the manufacturer’s Customer--Service department for assistance.

I/M Ready Test & I/M Readiness Hot Key:

The Ready Test can be used as a convenient readiness test tool by automotive technicians to determine if the tested vehicle is ready for an emission test. By visual and audible indication,you will learn a vehicle’s monitors readiness. Repairs to the emissions-control systems of a 1996 or newer vehicle cause the vehicle’s computer (ECU) memory to be cleared. The vehicle must go through a drive cycle to allow the ECU to perform a series of tests to ensure that the repair was successful, and before a state mandated emissions test can be conducted. But how will you know when it is ready? With this scan tool, you don’t have to drive around endlessly and continuously coming back to the repair shop for retest if all required tests by the ECU are completed. And you could also do a quick check of the vehicle to determine if it is ready to receive an emission test without the hassle of connecting your vehicle to the analyzer or having to use a complicated scan tool.In the following cases, this function is especially useful.

• You bought a used car and the check engine light had been cleared to mask potential problems.
• You disconnected the battery for tune-ups and other engine repairs, dead battery replacement, car radio installation and car alarm installation.
• You used a scan tool to clear the DTCs.
• Your car has been sent to repair.

I/M refers to Inspection and Maintenance that is legislated by the Government to meet federal clean-air standards. I/M Readiness indicates whether or not the various emissions-related systems on the vehicle are operating properly and are ready for Inspection and Maintenance testing.

The purpose of the I/M Readiness Monitor Status is to indicate which of the vehicle’s Monitors have run and completed their diagnosis and testing, and which ones have not yet run and completed testing and diagnosis of their designated sections of the vehicle’s emissions system.

The I/M Readiness Monitor Status function also can be used (after repair of a fault has been performed) to confirm that the repair has been performed correctly, and/or to check for Monitor Run Status.

Note: N/A means not available on this vehicle; INC means incomplete or not ready and OK means Completed or Monitor Ok.

CHECK ENGINE LIGHT:

Quickly and accurately to read the engine fault code, built-in DTC look up library to show the DTC definitions,make it easy to determine the cause of the Check Engine Light(MIL), and turn off Check Engine Light by erasing the trouble codes and Monitors reset.

Battery Monitor: NL101 could quickly check the vehicle’s battery health, read out the current battery value and give out 6 levels of warnings for your knowledge:

• A. <10.8V(before Starting): Too Low; Change your battery, otherwise, might not be able to start;
• B. 10.8V-11.8V(before starting): Slightly low; Difficult to start, please turn off other electronics and start vehicle to charge;
• C. 11.8V-12.8V(before starting): Normal;
• D. 12.8V-13.2V(after starting): Too Low; Might not be able to charge the battery, please check other electrical load;
• E. 13.2V-14.8V(after starting): Normal;
• F. >14.8V: Too High; Might damage the battery, please check the engine stabilizer.

Power Supply: The power of the NL101 is provided via the vehicle’s Data Link Connector (DLC). Follow the steps below to power it up:

1. Find DLC on the Vehicle: The DLC is the connector where diagnostic code readers interface with the vehicle’s on-board computer and usually located in the driver’s cab. A plastic DLC cover may be found for some vehicles and you need to remove it before plugging the OBD II cable. If it cannot be found, refer to the vehicle’s service manual for the location.
2. Plug OBD II cable to the vehicle’s DLC.

One Click "Help" for Data Stream & View Freeze Frame:

• This item enables you to view all data stream items and the live waveform of all selected items.Some data stream have the help information ,press the [?] .
• When an emission-related fault occurs, certain vehicle conditions are recorded by the on-board computer. This information is referred to as freeze frame data. Freeze Data is a snapshot of the operating conditions at the time of an emission-related fault.

Note: If DTCs were erased, Freeze Data may not be stored in vehicle memory depending on vehicle.

Location of the Data Link Connector (DLC): The DLC (Data Link Connector) is the standardized 16-cavity connector where diagnostic scan tools interface with the vehicle's on-board computer. The DLC is usually located 12 inches from the center of the instrument panel (dash), under or around the driver side for most vehicles. If Data Link Connector is not located under dashboard, a label should be there telling location. For some Asian and European vehicles, the DLC is located behind the ashtray and the ashtray must be removed to access the connector. If the DLC cannot be found, refer to the vehicle service manual for the location.

Package Accessories：

• Main Unit with OBD 16PIN Diagnostic Cable
• User’s Manual -- Instructions on Tool Operations
• USB Cable -- Connect to a Computer for Upgrading Online

DTC Lookup:

The DTC Lookup function is used to search for definitions of DTCs stored in the DTC library and for code breaker information.

1. From Main Screen (Figure 4.1), use the [UP] / [DOWN] scroll button and [RIGHT] / [LEFT] scroll button to select DTC Lookup and press the [OK] button.
2. From DTC Lookup screen,use the [RIGHT] / [LEFT] button to move to the desired character,use the [UP] / [DOWN] button to change selected digit/character and press the [OK] button to confirm.
3. View the DTC definition on screen. When DTC definition covers more than one screen,use the LEFT/RIGHT button or UP/DOWN button to view additional information on previous/next screens.

Here we list some frequently asked questions and answers relating to NL101:

• Question: System halts when reading data stream. What is the reason? Answer: It may be caused by a slackened connector. Please turn off the NL101, firmly connect the connector, and switch on it again.
• Question: Screen of main unit flashes at engine ignition start. Answer: Caused by electromagnetic disturbance and this is normal phenomenon.
• Question: There is no response when communicating with on-board computer. Answer: Please confirm the proper voltage of power supply and check if the throttle has been closed, the transmission is in the neutral position, and the water is in proper temperature.
• Question: Why are there so many fault codes? Answer: Usually, it’s caused by poor connection or fault circuit grounding.

Product description

The iCarsoft CR Pro is a Professional and powerful vehicle fault diagnosis tool for multi-brand vehicles (more than 40 kinds of vehicle makes) developed by iCarsoft Technology Inc. With a 4.0†TFT LCD and unique diagnostic software, it features full ECU diagnosis of most vehicle brands and test modes mainly include: CANBUS, ISO9141, KWP2000, and J1850 etc. It enables technicians to accurately diagnose complex problems. Note: Certain functions may be limited from the vehicle manufacturer due to the requirement of a special factory access code. This scan tool covers over 20 years of models, so some functions may not be available on all years/models.

• CR PRO VEHICLE COVERAGE: Nissan, Infiniti, Toyota, Lexus, Scion, Honda, Isuzu, Hyundai, Kia, Daewoo, Mazda, US Ford, Sprinter, BMW, Mini, VW, Seat, Skoda, Volvo, Porsche, SAAB, EU Ford, Holden, AUS Ford, Acura, Subaru, Mitsubishi, Dacia, Renault, Fiat, GM, Chrysler, Mercedes-Benz, Citroen, Jaguar, Peugeot, Audi, Opel, Land Rover, Smart, Suzuki, Vauxhall, Alfa-Romeo, Lancia
• CONTENTS: - Main Unit - Hardcopy User's Manual - Main cable - Data cable - TF Card (Within the main unit) - Nylon carry case
• SPECIFICATIONS: - Display: 4.0″ TFT LCD, 480*320 Pixels - Operation Temperature: 0°C ~ 50°C - Storage Temperature: -20°C ~ 70°C - Operating Voltage: 9 ~ 18V - Operating Current: 150mA@12V (typical) - Power Consumption: 1.8W (typical) - Dimension: 206*104.1*32.6 mm (L x W x H)
• VEHICLE COVERAGE (YEAR): - Works on most of 2001 and later OBDII compliant PETROL European vehicles - Works on most of 2004 and later OBDII compliant DIESEL European vehicles - Works on most of 1996 and later OBDII compliant US and Asian vehicles
• FIFTEEN SUPER ADVANTAGES: - Diagnose most Models (OBDII-16DLC) - Full System Diagnosis - Supports Oil Service Reset - Electronic Parking Brake (EPB) system maintenance - Battery Management System (BMS) (some vehicles do not enjoy this function) - Diesel Particulate Filter (DPF) Regeneration Control System - Electronic Throttle Control System (ETC) - Steering Angle Sensor (SAS) Calibration - Read &Clear DTC - Read Live Data - Supports Battery Test - Supports Data Review and Print

User questions & answers

Question:	Is this compatible for a 2001 volvo s80; 2017 volvo xc60 and 2018 chevy silverado
Answer:	Yes
Question:	Is this a real icarsoft car pro tool or a just a cleaver clone
Answer:	we are iCarsoft Dealer, from us you get the original one !!!
Question:	This scanner can diagnose & reset transmission problem for mercedes benz c230 and w203 2004 model
Answer:	Yes it can
Question:	will it work on US mercedes w210 year 2000 model
Answer:	No did not work on the W210

• FEATURES: Read or clear generic and manufacturer error codes, retrieve VIN (vehicle identification numbers) on 2002 or newer vehicles supporting mode 9, and reset the airbag light
• INCREDIBLY SIMPLE: Plug it into the 16-pin connector underneath the steering wheel, turn the ignition, and you're ready to go using only 2 simple buttons
• COMPATIBILITY: Works with most US vehicles 1996 and newer that are OBDII and CAN compliant and supports all OBDII protocols as these are required in all US vehicles after this date
• LCD SCREEN: Displays the meaning of over 3000 generic error code definitions in the database, it also clears trouble codes (DTC’s) and turns off the check engine light (MIL)
• HANDHELD: At 2.75" x 1" x 4.25" (26.25 inch cable) and only 8 ounces, it literally fits in the palm of your hand, plus it's powered by your vehicles, Data Link Connector so you don't even need batteries

User questions & answers

Question:	Will this fit on ford f150 2008 xlt
Answer:	Yes it should. Typically anything after 96 has an obd
Question:	Wich is better ms300 or ms309. what is a differance? thx
Answer:	The main difference I see is the ms309 can pull freeze frame data which is very helpful in determining what might have caused the DTC to get triggered. For that reason, I'd definitely choose ms309 over ms300. I assume this is just a rebranded Autel (the black ones).
Question:	Does it count misfires for each cylinder? (No code, but is occasionally skipping - I need to know which cylinder
Answer:	Unfortunately, the scanner does not count misfires for each cylinder.
Question:	is there any scanner that will check ABS
Answer:	Unfortunately, this scanner can not check for ABS.

Product features

SIMPLE SCAN

ONCE PLUGGED INTO YOUR VEHICLE’S 16 PIN OBDII DLC, THE UNIT WILL TURN ON AND PROMPT YOU TO START YOUR IGNITION. THIS DEVICE WILL BOTH READ & CLEAR GENERIC AND MANUFACTURER CODES. PLUS, IT’S POWERED BY THE OBDII DATA LINK CONNECTOR IN YOUR VEHICLE, SO THERE IS NO NEED FOR BATTERIES OR A CHARGER.

IN ADDITION

NOT ONLY DOES THE OBD II SCAN TOOL MS309 READ & CLEAR CODES, IT ALSO RETRIEVES THE VIN (VEHICLE IDENTIFICATION NUMBER) ON 2002 AND NEWER VEHICLES THAT SUPPORT MODE 9.

COMPATIBILITY

WORKS WITH MOST 1996 & NEWER US-BASED VEHICLES THAT ARE OBDII COMPLIANT (INCLUDING CAN) AND SUPPORTS ALL OBDII PROTOCOLS.

DISPLAYS OVER 3000 GENERIC ERROR CODES, CLEARS TROUBLE CODES (DTC’S), AND TURNS OFF THE CHECK ENGINE LIGHT (MIL).

• ➤【CHECKING CAR ENGINE TOOL】 The OM126P Enhanced OBDII scanner can read and erase the trouble codes that can cause emission problems in your vehicle in seconds, turn off the MIL (check your car engine) and reset the monitor, build a DTC lookup library you can find the related code definitions to help you determine if your car needs repair, to save you time and money, and dramatically improve your car lifespan / performance.
• ➤【EASY TO OPERATE】The OM126P car diagnostic tool equiped with 2. 4" TFT 262K true color LCD display screen to indicates the test results , with the silicone keypad you can easy to access the each menu options, the I/M Readiness hot key can check the state emissions readiness and drive cycle verification,Also, a wealth of car information is retrieved to find out all about your car without hassle for recording, car tracking, buying matched parts etc.
• ➤【WIDE RANGE DIAGNOSE】 Work on all after 1996 and newer vehicles models in the USA(OBD II&CAN) or other imported vehicles. Quickly read and erase the DTC on all OBD II protocols vehicles: CAN, J1850 PWM, J1850 VPW, ISO9141 and KWP2000 and support for 10 languages: English, French, Spanish, German, Russian, Italian, Finnish, Portuguese, Polish, Dutch, which make it easy to use for people from different countries .
• ➤【POWERFUL FEATURES】 Built-in 14 special functions in 1 car reader, read and erase stored emission related codes, pending codes, and show code definitions, data steam, freeze frame, on-board monitoring, and show the vehicle information,I/M reading,review the recorded DTC,review & print report. Support O2 sensor and EVAP system test, let you initiate a leak test for the vehicle’s EVAP system, identify trouble shooting related to fuel efficiency and vehicle emissions.
• ➤【WORRY-FREE SERVICE】 Plug & Play, no battery or charger required;OM126P OBDII diagnostic scan tool supports a lifetime free software updating and Review & Print diagnostic reports from the Auto fix ,via connect to a computer via USB (for Windows 7/8/10 ONLY), and we offer one year warranty , if you cannot comfirm its compatility, please feel free to consult us.

Product features

Why is OM126P so popular among customers? What are the special functions about it?

1. I/M Reading is to test Misfire/Fuel system/Comprehensive component.

2. On-Board Monitor Test can be utilized to read and results of on-board diagnostic monitoring, testing for specific components/syestems.

3. EVAP System Test let you initiate a leak of test for the vehicle’s EVAP system.

4. O2 Sensor Test allows retrieval and viewing of O2 sensor monitor test result for the most recently performed test from the vehicle’s on-board computer.

5. Review the recorded DTC, read hard (memory) / pending (intermittent) and historic codes and show definitions.

6. View stream data and freeze Frame, see the live data by graph or chart.

7. Review & Print can save or print the diagnostic report as need.

8. Vehicle Info will display the information such as VIN(Vehicle Identification Number), CID(Calibration ID) and CVN(Calibration Verification Number).

9.2.4’’ colorful LCD screen OBD Scanner,perform the full engine diagnosis and data for your car.

10.Pull engine related Generic and Manufacture specific, and pending trouble codes.

11.Reads and displays live sensor readings in text or graphs forms, supports unique 4 parameters compare in real time.

12.The OM126P's diagnostic speed is 2-3 times faster than other obd2 scanner with newest optimization algorithm in industry

13.Supports 10 languages and wide compatible all 12V Vehicles from 1996 and newer.

View Data Stream

Supports all data stream for compression ignition vehicles, there are 3 types of data: View all item, Select item and View graphic items. Let you view all data stream items and the live waveform of all selected items.

Steady Performance CPU

With best advanced STM-32 main chip set, The AUTOPHIX OM126P car code reader has a high speed and steady performance, which could fast read within 2-3 seconds, and quickly determind the problem of the car engine, check the engine light and show the live data.

Colorful LCD Display

The OM126P OBDII scanner has a .2.4 TFT 262K true color, 320*240 QVAG LCD display which indicates test results more Clearly and vivid,features with user-friendly UI design. The menu function is clear and there are six menu function options to choose from.

Data Review

OM126P OBD2 code reader can help you review the recorded DTC, which can review DTC, delete DTC data and delete all DTC data. Storing diagnostic data report for review and print, bulit in a lookup library to search for the definitions of DTCs stored in the DTC library and for code breaker information.

OM126P Enhanced Professional Automotive OBD2 Scanner

1. Identifies the Powertrain information and shows current data available to the scan tool.
2. Displays Freeze Frame Data; Used to clear DTCs and Freeze Frame Data.
3. Display the type of powertrain or emission related DTCs stored by a 4 digit code identifying the faults.
4. Request Oxygen Sensor Monitoring Test Results.
5. Non-continuously Monitored Systems test results.
6. Request for DTCs (pending) from Continuously Monitored Systems after a single driving cycle has been performed to determine if repair has fixed problem.
7. This special Control Mode requests control of the on-board system, test, or component bi-directionally (where applicable).

• 【COMPATIBILITY WIDELY】 No need battery nor internet connection, just plug the obd2 scanner for car into obd2 port to reset check engine light. The car diagnostic code reader is suitable for US-based car made after 1996 and EU-based car made after 2000 which equipped with OBD2 (OBDII protocols: KWP2000, ISO9141, J1850 VPW, J1850 PWM and CAN), which is for 12V car and light truck, but not for 24V truck.
• 【IMMEDIATE DIAGNOSE】 Diagnose your car in a few sec, read engine code in 4 sec, save your trip and hundred $$$ to the Auto Zone to get it checked. Go to the “DTC LOOK UP” and input code, it will give you common interpretation. Meanwhile, the possible cause of issue is displayed. I/M Readiness function assist you in diagnosing the issue that it checks vehicle emission-related monitors such as O2 Sensor, EVAP system etc, displaying Live Data& Freeze Frame. Help you pass the Smog Check easily.
• 【BATTERY TEST】This OBD2 scan tool can check the battery states, knowing the battery’s health. It's also equipped with 2.62 feet long OBD II cable and 1.8 inch colorful TFT screen, the sensitive physical buttons and non-slip design on both sides make you are able to use it flexible even wearing gloves.
• 【SCREENSHOT FUNCTION】 Screen shot function is really helpful, you can take car data photos by it. Export them from your PC or laptop via USB cable, fast and effective. When connected the obd2 reader, laptop will recognize it as removable device, you can copy and paste files for easily export.
• 【HIGH QUALITY SERVICE】 Lifetime free update are offered by this Automotive scanner code reader. We guarantee you’ll love the car diagnostic tool, and If you are not satisfied with our car code reader for any reason, send it back for a 100% no questions asked refund !

Product features

Enhanced OBD2 Diagnostic Scanner - TFT Color Screen

Full OBDII Diagnostic Functions:

• Read & Clear DTCs : identifies which section of the emission control system has malfunctioned.
• I/M Readiness Status : I/M Readiness allows you to check if the various emissions-related systems on the vehicle are operating properly so you can know whether your vehicle is ready for local emission inspection.
• Read Freeze Frame and Data stream : a snapshot of the operating conditions at the time of an emission-related fault.
• Read Vehicle Information : YA-101 Scan tool will tell you the specific information for the tested control unit, including unit type, version numbers, and other specifications.
• O2 Sensor Test : accurately identifies failures of Oxygen sensor and vehicle emissions related errors.
• On board Monitored systems Test : can be utilized to read and results of on-board diagnostic monitoring, testing for specific components/syestems.
• EVAP Test : initiates a leak test for the vehicle’s EVAP system.
• Battery Tester: · Our car diagnostic scanner can show Supports real-time battery monitoring, displays the voltage of your vehicle.

Built-in DTC Library

Generic codes definition convenient for you to search the definition of diagnostic trouble codes, clearly presenting detailed definition for each DTC you’re looking for.no need to search it one by one online which saves your time.

What is more: this hand-held engine code scanner shows possible causes for the fault codes, make it easier for car owner novices to understand what problems of the vehicles.

Turn off check engine light

The OBD2 scanner can find out the reason which causes the Check Engine Light on quickly and accurately, Just clear codes after certain repairs and the light will be turned off automatically.

Lifetime Free Update

Once connected obdii scanner, laptop recognize it as removable device, clean the original data, copy the updated file to the device, no need to install any drivers, so you always have the latest car model data.

Extensive Coverage & Languages

Works on most vehicles sold worldwide with the model year of 1996 or newer. For any compatible issues, you can consult us anytime.

support Multilingual menu: English, French, German, Spanish, Portuguese, Italian, Russian,Japanese,Chinese.

Great Optimized Live Data

• Fast reflashing time even reach 0.1millisecond

YA-101 optimized the livedata display algorithm, to ensure the real-time data display smooth and reponse fast, it's really exciting feeling without waiting or data delay.

• What live data can be read by this device?

How much data can be read depends on the vehicle, there are over 40 live data PIDs.

Such as: FUELSYS(fuel system status), LOAD_PCT(Calculated load value), ECT(Engine Coolant Temperature), SHRTFT(Short term fuel trim-bank), LONGFT(Long term fuel trim-bank), Engine RPM, VSS(Vehicle Speed Sensor), SPARKADV(Ignition timing advance for cylinder 1), IAT(Intake air temperature), MAF(Mass Air Flow), TP(Absolute Throttle Position), EQ_RATB1S1(Equivalence Ratio Bank 1, Sensor1), O2B1S1(Oxygen sensor output voltage), EVAP_PCT(Commanded Evaporative Purge), etc.

Product description

Firmware Version: 1.4.3

Software Version: Techstream_Setup_V15.00.026

Support all the diagnostic communication protocols needed Fit for Toyota cars since 1996

Function:

- Check Engine Light Shut Off

- Multi-Language Interface

- Freeze Frame Displays

- Internet Updateable

- User Friendly

- Heavy Duty Thick-Shielded Cable for best Test Results.

MINI VCI Support Fit for Toyota TIS OEM diagnostic soft ware:

PCB Board - FTDI FT232RL Chip

Update Method - By CD or link to download

Supported System - (32bit/64bit) Win XP/ Win7 Win10

Language Supported - German/French/Japanese/Spanish/Italian/English/Chinese

Features:

1.Support TIS OEM diagnostic soft ware

3.High performance with ARM CPU inside.

4.High reliability of products using SMD chip, and certified by CE and FCC.

Supported Protocols:

K-Line ISO 9141

KWP 2000 ISO 14230-4

SAE J1850 PWM

SAE J1850 VPW

CAN 2.0B ISO 11898

CAN ISO 15765-4

PURCHASE NOTES:

1. Installation need TURN OFF all firewalls on the computer and EXIT the anti software instead of disabling it for a few hours.

2.If you encounter installation problems, please contact us, we will will send you the ""Techstream"" software, help you solve the installation problems

3.If CDs is damaged when you received or your computer does not have a place for the CD, please feel free to contact us at any time to get software download link

4.The software is very large, so the installation will takes a lot of time, If you still don’t know how to install it, we can install it remotely for you, or you can find the installation video on the website such as Youtube, thank for your understanding

Package:

1x VCI J2534 Cable

• 16Pin MINI VCI OBD2 USB Interface Scan Cable for Toyota - MINI VCI for TIS Techstream supports TIS OEM diagnostic soft ware and all the diagnostic communication protocols needed for Toyota since 1996, for diagnose, coding etc.
• PURCHASE NOTES - Mini VCI diagnostic cable compatible with (32bit/64bit) Win XP/ Win7/ Win 10, and the installation need uninstall the Firewall and defender need to be closed in case it damages the software. = = = = If the 64-bit driver automatically disappears when you install it, it means that the computer's firewall and all anti software have not been closed or exited, please check these two places again and install again.
• 16Pin OBD2 MINI VCI Diagnostic USB Cable Supported Protocols - K-Line ISO 9141, KWP 2000 ISO 14230-4, SAE J1850 PWM, SAE J1850 VPW, CAN 2.0B ISO 11898, CAN ISO 15765-4. Firmware version is V1.4.3, Techstream version V15.00.026.
• MINI VCI Cable Diagnostic Test Scanner Function - MINI VCI check engine light shut off, multi-language interface, freeze frame displays, internet updateable, user friendly and others function, heavy duty thick-shielded cable for best test results.
• What You Will Get - We offer mini VCI J2534 cable 24 month service, any questions about OBDII cable converter adaptor, please contact us, the Techstream software will be sent to you by Email, we will reply you within 12 hours. You will get a MINI VCI cable scan tool, with CD inside the package, include 1. Mini VCI Driver for TOYOTA _1.4.3. Techstream_Setup_V15.00.026. // TS_loader // The drive of 32bit.msi and 64bit.exe // The path // Install Video = please watch twice

User questions & answers

Question:	Hello. will this program keys for 2012 toyota prius v
Answer:	Maybe
Question:	Does this work with 2013 Prius C
Answer:	Hi, dear friend, thank for your letter, yes, this mini VCI OBD2 J2534 will fit your 2013 Prius C. Thanks
Question:	How i install vci mini cable on windows
Answer:	Hi, dear friend, thank you for your letter, you can send me information after ordering, (440) 652-2784, we will send you the software download link and installation video and user manual. Best regards
Question:	will it program 06 lexus gx
Answer:	Hi, dear friend, thank you for your letter, yes, Mini VCI J2534 Cable is will suitable for 06 lexus gx470, please contact us in time after ordering, we will send you the new version of the software and installation video. Best regards

• ▲IMPROVED VERSION OBD2 SCANNER CAR DIAGNOSTIC TOOL - Pass EMC Certification, ROHS Certification and FCC Certification. Read & Clear diagnostic trouble codes for the check engine light, both generic & manufacturer specific codes, reset Check Engine light.
• ▲SUPPORT iOS & ANDROID - Recommend "OBD Fusion(9. 99USD)" and "inCarDoc(0~9. 99USD)" for iOS. Recommend (in-app purchase) "Torque Pro" for Android. Third-party apps may need to pay to get full function. Please wait wifi connection done in 10 seconds.
• ▲COMPATIBLE VEHICLES - Works with model year 1996 and newer vehicles sold in Unite States (except for cars with 24V voltage). Include VW Ford GM Dodge BMW Chevrolet Audi Subaru TOYOTA Honda Mazda Kia Benz and more OBDII vehicles.
• ▲DISPLAY REAL-TIME SENSOR DATA - Display data including Engine RPM, Calculated Load Value, Coolant Temperature, Fuel System Status, Vehicle Speed, Short Term Fuel Trim, Long Term Fuel Trim, Intake Manifold Pressure, Timing lights, Timing advance, Intake Air Temperature, Air Flow Rate, Absolute Throttle Position, Oxygen sensor voltages/associated short term fuel trims, and so on.
• ▲18-MONTH - 100% money back for quality problems. Any question with our WIFI OBD2 scanner, please contact us freely!

User questions & answers

Question:	Will this work on a 2003 7.3l f
Answer:	Yes, most cars have OBD2 "on board diagnostics 2", it is a standard.
Question:	Do you have to pay for an app upgrade to be able to clear codes
Answer:	No, our recommend free app in listing page will clear codes. The paid version needed if you want to get more real-time sensor data or more information of your engine.
Question:	Would you please tell me about the firmware version of this OBD tool? thanks in advance
Answer:	Dear Customer, this OBD2 scanner wifi uses ELM 327 firmware
Question:	Will this work with dash command on iOS
Answer:	Yes our obd2 scanner will work with dashcommand on iOS.

Product features

Support Protocols:

SAE J1850 PWM(41.6Kbaud)

SAE J1850 VPW(10.4Kbaud)

ISO9141-2(5 baud init,10.4Kbaud)

ISO14230-4 KWP(5 baud init,10.4 Kbaud)

ISO14230-4 KWP(fast init,10.4 Kbaud)

ISO15765-4 CAN(11bit ID,500 Kbaud)

ISO15765-4 CAN(29bit ID,500 Kbaud)

ISO15765-4 CAN(11bit ID,250 Kbaud)

ISO15765-4 CAN(29bit ID,250 Kbaud)

SAE J1939 CAN(29bit ID,250*Kbaud

A Must Have Scan Tool for Your Vehicle, Compatible with iOS and Android

Access Whole New World of Information about Your Vehicle

Practical Scan Tool You Deserved

• Provide you with the trouble code causing the Check Engine Light to turn on.
• Display real-time sensor data on your phone or tablet with the third-party App.
• Compatible with iOS and Android.