11 best reese pro series trailer jacks

Product description

Round Jack.

• Pro Series 1401460303 Weld-On Jack; Topwind; 5000 lbs.;
• Authorized Dealer - 100% Satisfaction Guaranteed
• Pro Series
• 1401460303
• Warranty: Yes

User questions & answers

Question:	does this have a removable plate on the bottom where a wheel can be used instead
Answer:	Bottom skid plate is welded on
Question:	How big of a circle does the handle spin when rotating it
Answer:	The turning diameter would be 14 inches. The crank handle is 7 inches from center of jack to turning knob. It stows to straight up and down with jack.
Question:	What is the outside diameter of the weld on pipe
Answer:	2 inches.
Question:	How many inches of lift does it have
Answer:	The fully retracted jack is 11 1/2 inches from the bottom of the foot to the center of the mounting flange. Fully extended adds 10 inches lift.

Product description

Square Jack.

• Square Jack
• Part number: 1401520383
• Package Weight: 15.35 pounds
• Oem equivalent part number: FCJM1401520383

User questions & answers

Question:	how long is retracted lenght and what is the travel lenght for this jack
Answer:	Yes for clamp on installations. it has bolts and backer plates.
Question:	what size is the mount tube and pin
Answer:	I use mine in saltwater. But it never gets in the water. It is zinc plated and it will rust.
Question:	does this model PS140 1080 303 have the 15" lift or the 10" lift. doesnt list
Answer:	The foot on this jack is adjustable. It has holes that allow it to slide up and down. Held in by a very stout pin. 8” is do able but you won’t have much clearance if you leave the foot attached. I got an offset receiver hitch Which gives me extra height. I still had to cut part of the tube on the foot off to remove it for extra clearance before launching.
Question:	is it made to swivel when not in use
Answer:	Yes it is plastic, I use mine on a cement driveway. Works great

Product description

Square Jack.

• 1401500383

Product description

Easily jack up your trailer with the Reese Square Adjustable Cranking Topwind 15 Inch Travel Trailer Jack 8000 lbs. From trailers and vehicles to boats and RVs, this jack can do a little bit of everything. With an 8,000-pound lift capacity and an 8,000-pound support capacity, this thing is the real deal. The handle features a topwind claw design that makes it easier than other designs to raise and lower the load. This jack is also built to weld directly to the frame, ensuring a snug fit everytime. Reese Square Adjustable Cranking Topwind 15 Inch Travel Trailer Jack 8000 lbs is the perfect solution for your trailer lift needs.

• DYNAMIC: Square jack dramatically improves side load strength
• VARIETY: Drop leg and fixed leg models available
• SWIVEL: Tubular swivel models include mating mount and pull pin
• CORROSION RESISTANT: Features a black powder coat finish that helps avoid rust and corrosion
• TOPWIND: Handle has smooth, ergonomic design for easy cranking

User questions & answers

Question:	Is this weld on
Answer:	Yes, it is weld on.
Question:	what size is the tubing
Answer:	Operation Type: Manual Type: Topwind Capacity: 8000 Pound Maximum Lift: 15 Inch Retracted Height: 22.9 Inch Extended Height: 51-1/2 Inch Color/ Finish: Black Painted Outer And Clear Zinc Plated Inner Tube Material: Steel Mounting Type: Weld-On Bracket
Question:	Can the handle be easily removed
Answer:	Yes, it is removed by removing a small bolt and nut that passes through the shaft and the handle.
Question:	what size is the tubing
Answer:	Outside is 2 1/4 And In side is 2 inch

Product description

Nobody wants their boat or trailer rolling off into the sunset. With the Pro Series Towing 5,000 Pound A-Frame Topwind Trailer Jack Tube, your receiver style trailer will stay grounded when it's not in use. This trailer jack is not vehicle specific, but fits with A-frame couplers. With a 5,000 pound lifting capacity, this jack can be used for a variety of marine and other recreational applications. This ergonomically designed jack features a topwind crank with a smooth and comfortable design that's easy to operate. Precision fitted parts provide added stability and proven reliability for long-term use. Accomplish dependable vertical and side load capacity that puts your mind at ease. Look no further than the innovative Pro Series Towing 5,000 Pound A-Frame Topwind Trailer Jack Tube with 15 inches of travel.

• TOPWIND CRANK: Topwind crank A-frame jack with a tube design for marine, utility, and recreational trailers
• EASY TO USE: Smooth, comfortable, ergonomic design makes it easy to operate
• DEPENDABLE OPERATION: Offers dependable vertical and side load capacity
• EXTRA DURABLE: Precision fitted parts provide added stability and proven reliability for long-term use
• WHAT'S INCLUDED: Includes 1 A-frame topwind trailer jack with weld-on or bolt-on mounting options; compatible with A-frame couplers

User questions & answers

Question:	What is the diameter of the jack tube
Answer:	3 inches
Question:	What is distance between mounting plate and bottom of jack when retracted
Answer:	about 10 inches
Question:	Does this come with mounting bolts
Answer:	Yes, I believe it does come with mounting bolts. My previous jack was welded so I had to cut it out-pain in the rear end.
Question:	What size mounting bolts does it need
Answer:	I used 3/8 grade 8 bolts I believe

Product description

MetalShield finish resists rust and corrosion

• Triple ball mount

Product description

The innovative Pro Series Complete Round Bar weight distribution is engineered to provide the features you expect in a weight distribution kit at an economical price.

• New combination single piece cast head
• Provides everything needed to improve towing, safety and performance right out of the box
• Pre-installed and torqued sway control ball and 2-5/16" hitch ball, U-bolts and chains
• Fabricated head and welded hitch bar
• Includes friction sway control and mounting hardware

User questions & answers

Question:	How long are the weight distributing bars from the elbow to the chain
Answer:	The brackets are 6" tall ...and the bolt slots are for 1/2" bolts...hope this helps
Question:	I bought the wrong size can i put a 2" ball on it
Answer:	I believe it was designed for a 5/8" shaft
Question:	do you have to remove bars when backing up like some other units
Answer:	About 1/8 inch. It's pretty substantial. Galvanized too.
Question:	Will this accommodate a 5000 lb rv
Answer:	Send note to company , they should send you a new handle.

Product description

Camco's Eaz-Lift Elite Weight Distributing Hitch Kit is designed to provide trailers with a smoother ride than that found in other hitches via its interchangeable bars that have positive latching action for operation. It includes a round bar weight distributing hitch, sway control and hitch ball. The 2-5/16" hitch ball and sway control ball are pre-installed and torqued to specification on the hitch head. The U-bolts and chain package are pre-installed on the spring bars. It has a maximum tongue weight of 1,000 lb. and a maximum gross weight rating of 10,000 lb. Mounting hardware is included.

• Your purchase includes 1,000-pound weight distributing hitch, sway control, 2-5/16" hitch ball & mounting hardware
• Product dimensions – 31” L x 11.5” W x 7.44” H | Hitch ball – 2-5/16” | Tongue weight limit – 1,000 lbs. | Gross weight rating – 10,000 lbs.
• U-bolts and chain package are pre-installed on spring bars
• Eaz-lift Elite Weight Distributing Hitch Kit allows you to save time with pre-installed components
• Hitch ball and sway control ball are pre-installed and torqued to specification on adjustable ball mount

User questions & answers

Question:	How do I adjust the sway bar? Tight or with a little play in it? The instructions say NOTHING about the sway bar adjustments!! Help
Answer:	Get on level ground without any big turns...the sway bar should only be put on once you're heading out for the trip...I put mine on tight...used a wrench to tighten it to pretty tight...not super tight...bring the wrench incase you notice that it needs to be adjusted on the trip...so far with 2 trips...one was a close weekend trip and another was 2,500 miles...all I needed was the bar, my wrench and a rubber ended mallet...the tighter I made the sway bar...the better my trip was...that was just my experience...and I removed it when I had to make hard turns...
Question:	my 30 ft Jay Flight TT tonge wt is 800 but i plan on adding batteries to bring it close to 1000Ibs can I still buy 48058? Can I use my 2 5/16" ball
Answer:	I don't think it would be a good idea to run this unit at close to its maximum capacity. Trailers have a tendency to get loaded up over time, and I would not want to have a road incident where the insurance company could say I was running my rig unsafely. The 48069 1200 lb unit is only $5 more, I'd go with it. I'm guessing I'm at 600-700 lbs tongue weight on my trailer - it makes a huge improvement in handling. It comes with the 2 5/16" ball. You might consider an electric tongue jack, you'll find it really helps out to set the chains -- you have to jack the rig way up to do so, and most hand crank jacks don't have the range you need without a multi-step blocking and raising corner jacks routine.
Question:	Is the shaft on this set up solid steel
Answer:	Shaft????? Or shank, If you talking about the shank yes it is very solid,However didn't work my truck because it has a 10inch lift, so the shank was too short , so I had to buy another shank, which was a longer one that cost me about $200. If u have a non lifted truck or a small lift on it you'll be fine .
Question:	Is hitch ball height adjustable on shank? The picture blocks that view
Answer:	Not only is the height adjustable, but you can tilt the hitch to allow the proper amount of flex in the torsion bars. Try the adjustment with the hitch connected, the trailer loaded with about 10% of the gross trailer load as a hitch weight. Then adjust the hitch height and tension bars so the tow vehicle drops about one inch with everything connected and properly loaded.

Product description

The powerful REESE Towpower Trailer Jack fits tongues 3” to 5” and helps effectively raise and lower trailers with a capacity up to 1,000 lbs. Operating with a 1:1 gear ratio, the side-winding handle with a wire-grip knob allows for fast and smooth usage while a heavy-duty swivel mechanism and pull-pin release make it easy to access the device when you need it, and store it away when you don’t. For added mobility, this jack includes 6” wheel that glides easily and lowers the friction to help you move a trailer into position with minimal effort.

• Features 1000 pound capacity
• Side winding handle with 1:1 gear ratio provides fast operation
• Heavy duty swivel mechanism for easy use
• 6 inch wheel to move your trailer into position for easy hook-up
• Fits tongues 3 inches to 5 inches

User questions & answers

Question:	If "Overall height 23 -1/5" Retracted Length 12-3/4"" is correct, then wouldn't the max lift be 10 3/4"? That would not be enough lift my use
Answer:	I haven't done any measurements on my trailer lift but your figures seem accurate from my use of said lift.
Question:	drill press
Answer:	No, the bracket that comes with it is plenty stout enough to attach to the tongue.
Question:	does it come with installation hardware like brackets and screws
Answer:	Yes, it does. It comes with long bolts and brackets so you are able to "sandwich" the frame of your trailer between the brackets and the unit.
Question:	what is the overall length when retracted and when open to maximum
Answer:	Overall height 23 -1/5" Retracted Length 12-3/4" Max Lift 22-7/10"

Product features

REESE Towpower - High Capacity for Easy Up and Down

The REESE Towpower Trailer Jack fits tongues 3” to 5” and supports a wide variety of vehicles with a capacity up to 1,000 lbs. Operating with a 1:1 gear ratio, the side-winding handle with a wire-grip knob encourages fast, smooth usage.

Swivel-Design for Easy Stowing

Heavy-duty swivel mechanism is designed to help you safely and easily stow away the jack in between uses. Use the pull-pin release to quickly access the jack when you need it, or store it away when you don’t.

1,000 Lb. Capacity

The REESE Towpower Trailer Jacks fits tongues 3” to 5” and helps easily raise and lower trailers with a capacity up to 1,000 lbs.

Swivel Access

Heavy-duty swivel mechanism with a pull-pin release makes it easy to access the jack when you need it, and store it away when you don’t.

Operates In Seconds

Side winding handle with a wire-grip knob operates with a 1:1 gear ratio for fast, smooth usage. Sturdy 6” wheel helps to easily move your trailer into position.

REESE

Founded in 1952, REESE has become a household name in the heavy-duty towing industry and a market leader in automotive and recreational product solutions. With proven designs that exceed the industry standards, we are the brand of choice when performance is the expectation. REESE caters to the towing needs of everyone from recreation enthusiasts to heavy-duty agriculture users by manufacturing the largest selection of receiver hitches; ball mounts and hitch balls; trailer and hitch locks; couplers, jacks and winches; and electrical and lighting components. For us, performance, safety, and durability are always front and center. They’re the reason why people ask for REESE by name.

Product description

Reese Towpower A-frame Jack is designed to provide excellent facility for mounting or dismounting heavy weight. It features reposition capacity and includes a weld-on mounting bracket.

• Designed to provide excellent facility for mounting or dismounting heavy weight
• Includes a weld-on mounting bracket
• 2000 lb. capacity

User questions & answers

Question:	Is the Jack foot plate removable to get the tube through the trailer tongue
Answer:	Inside curve - eye=2 1/2 " center - short end = 1 1/2 " center - long end = 8"
Question:	On the mid-center 3 bolt triangular piece, does anyone know the measurement from the center of each bolt hole to bolt hole? Mine are 5 inches apart
Answer:	The video features the 5" x 14"
Question:	How high is the lift of this jack? That is to say, what is the difference between the fully extended and fully retracted lengths
Answer:	I don’t believe they would work. You have to tie them through something. We have ours tied taunt through the mesh medal work on the swim deck of our houseboat.
Question:	What is the diameter of the fixed lower barrel
Answer:	the top of the bumper might be too short to hang over your tubes nicely. Unless you can hang it over just right... might fit oddly.

Product description

Reese Towpower Trailer Swivel Mount Jack has a 1,000 pound capacity with a 25-inch lift. The side mount swivel jack is easy to use just pull pin, swivel into position and release pin for auto locking. The sidewind crank handle has a 1 to 1 gear ratio that provides fast and easy operation. The jack mount fits 3 to 5-inch trailer tongues.

• Heavy duty swivel mechanism for ease of operation
• Sidewind gear ratio of 1 to 1 provides fast and easy operation
• Features a 4 inch by 6 inch footplate for increased surface area and tongue stabilization
• 10 inch travel and 1,000 pound capacity

User questions & answers

Question:	Bolts onto tongue? Or does it need some special mount on the tongue
Answer:	Yes
Question:	i would like to purchase this, but description says "usually ships between 1 to 2 months." is that a misprint
Answer:	he breaker simply unscrews from the panel after disconnecting the wires, and assuming the 6 amp breaker is the same diameter, it will fit in the same hole.
Question:	I'm putting this on a trac vac leaf trailer that mounts to the back of my john deere riding lawnmower. how low can it go
Answer:	The one I got did not come with an in line fuse. It would be redundant and not necessary.
Question:	Is there a trick to getting the swing pin to move? It came pre-installed and it doesn't seem to have any give
Answer:	Minimum protection. I am in Putuxent River on the Chesapeake so salinity is not as the ocean would be, however, I replay all my galvanized trailer and boat parts with a $6 can of 20oz cold zinc galvanizing spray to help avoid early rusting.