11 best led tail lights

Product description

Features

Dual Brightness: The Dim mode is Tail lights or DRL, while the Bright mode is Brake lights or Turn Signal lights.

High Brightness LED: 54SMD 3014 chipset & 3SMD 3030 chipset.

Working Voltage: 9-30V (fit 12V, 24V vehicles).

Output Wattage: 3W/bulb (Low Power Consumption).

Color: Brilliant Red.

Service Life: Up to 30,000 Hours.



Note: Load resistor or flash relay might be needed to prevent the hyper flash when replacement for Turn Signal Lights.



Warranty: iBrightstar Warranty for 1 year from date of purchase. Warranty type: Exchange or replacement.



IMPORTANT NOTICE! Please confirm the bulb base before placing an order.



iBrightstar is a registered brand with Amazon. Please contact us if there is any questions or other requests! Please check the bulb base before placing an order. If the customer order a wrong size it will cause doesnt fit their car. Since LED bulbs have no wattage with the stock bulbs and resulting in a smaller current when the car system detected the current smaller than before it will cause flasher to hyper flashing or created error. Requires a resistor or flash relay to prevent the hyper flash.

• (Set of 2 Bulbs)54SMD 3014 & 3SMD 3030 high Brightness chips per bulb,Working Voltage:9v-30v
• Fits:1157 BAY15D 1016 1034 1157 1157A 2057 2057A 2357 2357A 2357NA 2397 3496 7528 p21/5w etc.Easy installation, plug and play.
• Application:Brake Lights,Tail Lights,Daytime Running Lights etc. Load resistor or flash relay might be needed to prevent the hyper flash when replacement for Turn Signal Lights.
• Advantage:Exclusive design, 300% brighter than original halogen bulb, full Aluminum Housing with Projection lens for Maximum Light output and better heat distribution,built in Constant Current IC for Longer life span & Low Power Consumption.
• Please double check owners manual or original bulb number to confirm before placing an order. Any other problem please feel free to contact us, we are always here to satisfy of you.

User questions & answers

Question:	Will the red bulbs have the same 2 polarity connector on the base like the yellow one
Answer:	Yes
Question:	will the red bulbs work well the red lens or should I order white bulbs
Answer:	yes i have red in my red lenses on my tundra. i think the white will work fine too. just know that these are too big for the back up lights on a tundra which is what i intend the white to work in. yellow will work in the blinkers just fine. those are yellow bulbs in clear lenses on the tundra (2004-2006 at least) so get 2 yellows and 2 whites or reds but not all three. i have not looked for the led lamps to fit in the backup socket yet
Question:	It says 9-30 volt, but in product details is says 12 volt. My vehicle is 24 volt. Will they work
Answer:	Since it say 9 to 30 volt , I would say yes it will ...
Question:	I don't see size 2357 here what number should I buy
Answer:	Size: 1157. 1157 and 2357 are the same size, also compatible with these size: BAY15D 1016 1034 1157A 1178A 1196 2057 2057A 2357A 2357NA 2397 3496 7528 94 etc.

• (Set of 2 W2.5x16q D.F. wedge base 3156/3157 red LED bulbs) LED Chips: 39 pieces high quality,high power with high performance led chips per 3156 3157 LED bulb ---360 degree full angle illumination with projector lens design
• Compatible with both standard and CK / SRCK type. Voltage: 12V - 24V, Built in stable current IC driver for longer lifespan. Color: Pure red.
• Non-polarity. Cross reference number: P27W/7W, 3157/40610, 3157/17172, 12450004, 78633, 17945, 3157, 3457, 4114LL, 3056, 3055, 3155, 3156, 3456LL, 3457, 4057LL, 3156/21863, 9442003, 78625, 17941, etc.
• Application: Used for upgrading the stock incandescent dim rear turn signal blinker light, brake stop lights, tail lights, side marker light amp for much safer driving and luxury looking,load resistor maybe required to avoid the fast blinking issues.
• Warranty: fully ONE YEAR guaranteed for the manufacturer defect.please check the fitment note application before purchasing.

User questions & answers

Question:	i have 2000 ford taurus do i need a load resistor to use those led bulb
Answer:	Yes you will need load resistors to stop hyper-flash. They are easy to install.
Question:	What is/are the Lumens
Answer:	Here goes, I hope this helps.. Replace a 75W bulb with an LED bulb that gives you about 1100 lumens Replace a 60W bulb with an LED bulb that gives you about 800 lumens Replace a 40W bulb with an LED bulb that gives you about 450 lumens. Confusingly, higher Kelvin temperatures (3600–5500 K) are what we consider cool and lower color temperatures (2700–3000 K) are considered warm. Cool light is preferred for visual tasks because it produces higher contrast than warm light. Warm light is preferred for living spaces because it is more flattering to skin tones and clothing. A color temperature of 2700–3600 K is generally recommended for most indoor general and task lighting applications. Color Temperature is not an indicator of lamp heat.
Question:	Would there be need for a resistor to prevent hyper flashing if im only using them as a brake lights. My turn signal uses a separate bulb.2006 Corolla
Answer:	I switched my break and blinker bulbs. My blinker hyper flickered but my brake lights didn't. So I have to put resistor for blinkers only. I have a tacoma. Hope this helps
Question:	Anyone have any issues with them blinking very fast like the bulb is out. They are working but it's very fast blinking. 2013 Dodge Durango
Answer:	It's called Hyperflashing. You have to install a resistor on each LED bulb that flashes for the turn signal (one on each taillight). LED's draw a lower voltage than normal bulbs do so the computer thinks that you have a blown bulb and is signaling you to replace it. You can buy them online, at Walmart, or most auto stores. Simple to install. They look like tiny stereo amplifiers with a wire out each end. Don't even have to cut any wires in the harness. Just use a splice connection that has a spot for the wire your splicing in and a open slot to allow the cars wire to pass through. Put one wire on the ground wire to the light socket and the other end on the flashers/turn signalwire. You can check the owners manual or a repair manual for the colors, but if you have a taillight with multiple bulbs then you should have one socket that has two wires into it, a colored one (for parking light only) and a black ground wire. The socket that flashes will have 3 wires going in for ground, parking, and brake/flashers. The one that's a different color is the flasher. Be SURE to mount the resistor where it won't touch any wires when the taillight is reinstalled because it gets very hot while the turn signals are flashing and can melt the coating causing a short. You can mount it with double sided foam tape, but I recommend using short self tapping screws so it can't come loose later on. Mount it to either metal or hard plastic. They only cost between $9 and $19 depending on where you get them, and it's about 15 minutes for each light.

Product features

Comparison Between Stock Halogen Lamp VS Alla Lighting 3157 LED Red Bulb

• Alla Lighting 2835 39-SMD 3157 LED bulbs shows super bright pure red , yet the stock lamp shows quite dim yellowish red color
• Alla Lighting 2835 39-SMD 3157 LED bulbs has much bigger difference between the high intensity and low intensity light output, about 900 lumens for high intensity, and 200 lumens for the low intensity, yet for the stock lamp is about 250 lumens for the high intensity light output.
• Alla Lighting 2835 39-SMD 3157 LED bulb draws about 4.9W for high intensity yet the stock lamp draws about 28W, led bulbs draw much less current than stock lamps
• Alla Lighting 2835 39-SMD 3157 LED bulb makes your car more easily noticed while stopping by switching to braking mode,and also makes your car look much more luxury than stock lamp, more attractive.
• Alla Lighting 2835 39-SMD 3157 LED bulbs is 360° full angle degrees light output, the same light theory as the stock lamp for the best light performance.

Super Bright LED Lights

Super Bright LED Lights

360° Light Output

Premium Package

Product Specifications

• Premium projector lens
• Advanced aluminum heat sink material
• Built-in CK compatible LED driver
• High Power 2835 SMD LEDs

Product Dimension

• Length: 2.15inch
• Width: 0.88 inch
• Diameter: 0.71 inch (projector lens)

Product Features

• Wide Working Voltage: 9V ~ 30V
• Non- polarity bulb
• Compatible both CK and standard socket

Optional Colors

• 6000K Xenon White
• Pure Red
• Amber Yellow

Product description

This bulb is compatible for both CK/SRCK and standard socket, Non-polarity design. Best value in the market!



Features

Dual Brightness: The Dim mode is Tail lights or DRL, while the Bright mode is Brake/Turn Signal lights or Back Up Reverse lights. The bulb run in Bright mode when your bulb only function in one mode.

High Brightness LED: 54SMD 3014 chipsets & 3SMD 3030 chipsets.

Working Voltage: 9-30V (fit 12V, 24V vehicles).

Output Wattage: 3.8W/bulb (Low Power Consumption).

Color: Xenon White 6000K.

Waterproof: IP65.

Service Life: Up to 30,000 Hours.



Note: Load resistor or flash relay might be needed to prevent the hyper flash when replacement for Turn Signal Lights.



IMPORTANT NOTICE! Please confirm the bulb base before placing an order.



iBrightstar is a registered brand with Amazon. Please contact us if there is any questions or other requests!

• (Set of 2 Bulbs)54SMD 3014 & 3SMD 3030 high brightness chips per bulb,Working Voltage: 9v-30v (fit 12V, 24V vehicles).
• Fits: 3056, 3156NA, 3156K, 3156, 3156A, 3156AK, 3156NAK, 3047, 3047LL, 3047K, 3057A, 3057ALL, 3057, 3057ST, 3057K, 3057KX, 3057X, 3057KLCP, 3057LL, 3155, 3155LL, 3157A, 3157AK, 3157 ,3157K, 3157X, 3157LL, 3157ST, 3157KX, 3157NA, 3157NALL, 3157NAK, 3357A, 3357ALL, 3356, 3357, 3357KNA, 3357LL, 3357K, 3454NA, 3457A, 3457ALL, 3457AK, 3457, 3457K, 3457NA, 3457NAK, 3757A, 3757AK, 3757ALL, 4057, 4057LL, 4057K, 4114, 4114LL, 4114K, 4157, 4157LL, 4157K, 4157NA, 4157NAK, 5702 ect.
• Application: Back Up Reverse Lights, Brake Lights, Tail Lights, Parking Lights, Side Marker Lights, Daytime Running Lights etc. You will need load resistor or flash relay to prevent the hyper flash when replacement for Turn Signal Lights.
• Advantage: Non-polarity design, Compatible for both CK/SRCK and Standard socket. More than 300% brighter than original halogen bulb, full Aluminum Housing with Projection lens for Maximum Light output and better heat distribution, built in Constant Current IC for Longer life span & Low Power Consumption.
• Please double check owners manual or original bulb number to confirm before placing an order. Any other problem please feel free to contact us, we are always here to satisfy of you.

User questions & answers

Question:	How hot do these get compared to a standard 3157? i've had overheating problems in my rzr with the standards
Answer:	this only fit Turn Signal Light Bulb Front/ parking light in your car, make sure it was installed in the right position.
Question:	Is this a pack of 2 or just
Answer:	1 year
Question:	Hello I ordered these and my package was “delivered” but never received. There is no option on here to contact seller
Answer:	Yes, it will hypeflash any vehicle unless that vehicle has factory LED's
Question:	Will this fit my 2005 surburban
Answer:	Not a awnser but more of buyer protection these bulbs only lasted two months .I had four one went out and no bull and the others followed telling me it's not a defective bulb.just poor quality

• Package Includes: (Pack of 2) 912/921 replacement reverse light LED bulbs, 6W per bulb, 12-16V Wide voltage, 500Ma current, bulb size 1.57in(L)*0.59in(W)*0.35in(H), net weight: 6g/pc
• 300% Brighter: Each 921 bulb has 15 pieces high power 2835-SMD LEDs, 3 times brighter than original reverse light bulbs. 6000k white color light brings your car a refreshed new look
• CANBUS Error Free: Built-in intelligent IC driver for better performance. Energy-saving, low temperature, long lasting. Comparable size with stock 921 bulbs, easy to install
• Suit for Socket: T15, 912, 921, 906, 904, 902, W16W, just plug and play without modification. ONLY used for backup reverse lights
• Note: Amazon filter system may not be 100% accurate, the bulb size may vary between trim of your vehicle. Please double check owners manual or original bulb size to confirm

User questions & answers

Question:	Anyone try these on a 2016 chevy malibu LT? Any issues with the lights staying lit and never shutting off
Answer:	Dear customer, I'm sorry these 921 led bulbs will not compatible with chevy malibu vehicles. Please don't order these for chevy malibu. Thanks
Question:	Does it fit Toyota rav4 2019 reverse light
Answer:	The 2019 Rav4 is different than the 2018. Go to the Sylvania website and look at their bulb application chart for the 2019. If the reverse lights are 921 bulbs, these will work.
Question:	Is this plug and play
Answer:	Yes, not sure what you are using them for but for my 2017 Jeep Cherokee Trailhawk they only replaced the inside reverse lights, the ones on the hatch. They are really bright and helped a lot for the backup camera at night.
Question:	What’s the warranty? My light is flickering already
Answer:	Sounds like a poor connection I would check that first// check with Amazon about the warranty // or email Auxito //

• PERFECT FIT - SAE & DOT FMVSS-108 certified standard 6" size makes it easy to upgrade the dim, burnt-out, or damaged lights on your tractor, trailer, or work truck.
• READY FOR THE WEATHER - With a sonically sealed, submersible, IP67 waterproof rating, our lights are better suited to deal with the elements. Go ahead, back them into a lake, they won’t mind.
• BRIGHTER LIGHTS SAFER NIGHTS - We designed our tail lights with 10 super-bright colored LEDs behind colored diffused polycarbonate lens for true to color, improved visibility. Why? Because getting rear-ended can really ruin your day.
• WORKING SMARTER NOT HARDER - We like it when things are easy, so we’ve included an easy to use grommet for you to upgrade your lights in mere minutes. We also added a space-saving 90 degree connector with 12" of wiring for installation in tight spaces.
• STAND OUT - Our amber and red lights offer two intensity levels to function as parking lights or turn/brake lights, while the white lights offer a straightforward, one intensity, super-bright reverse/back-up light.

User questions & answers

Question:	Are the measurements provided with the rubber garment on or off the led
Answer:	led
Question:	How are they mounted
Answer:	Oval cutout in your trailer, truck bed or rack, gasket gets installed around edges and then the light gets installed into it. It is held in by friction . And let me tell you I had to beat mine in so they aren’t coming out easily that’s for sure. I used a screwdriver to pry out the old ones. I had to YouTube it to get the full concept.
Question:	How do i tint these
Answer:	u dont
Question:	Plug and play, or will I need a resistor or something else to make them work on my Toyota
Answer:	Mine was for my one ton dodge duality and fit right into my aluminum flatbed. They were already pre cut. I plugged them in and good to go. They actually make my turn signals glad faster, but once I plug in my gooseneck trailer. They slow back to normal. I could change the flasher under the dash, but I’m really not sure how they would flash after plugging my trailer in again.

Product features

NO WASTED TIME

When you’re deciding if you should upgrade to LEDs, one major consideration is “time invested vs reward.” Let’s make it easy for you. Our lights are the industry standard 6” oval lights so no modification is needed to install them. The included grommet quickly locks your lights in place and the lights are direct, wire for wire, replacement for your dual filament stop/tail turn/parking lights (amber/red) and reverse lights (white). It doesn’t get easier than this.

PERFECT FIT

SAE & DOT FMVSS-108 certified standard 6" size makes it easy to upgrade the dim, burnt-out, or damaged lights on your tractor, trailer, or work truck.

READY FOR THE WEATHER

With a sonically sealed, submersible, IP67 waterproof rating, our lights are better suited to deal with the elements. Go ahead, back them into a lake, they won’t mind.

BRIGHTER LIGHTS SAFER NIGHTS

We designed our tail lights with 10 super-bright colored LEDs behind colored diffused polycarbonate lens for true to color, improved visibility. Why? Because getting rear-ended can really ruin your day.

WORKING SMARTER NOT HARDER

We like it when things are easy, so we’ve included an easy to use grommet for you to upgrade your lights in mere minutes. We also added a space-saving 90 degree connector with 12" of wiring for installation in tight spaces.

What's Included?

• 6" 10-LED Oval Tail Light - Red
• 6" 10-LED Oval Tail Light - White

Product description

Our MaxxHaul universal square 12V combination 38 LED signal tail light is designed for use on most trucks, trailers, Jeep, boats, buses, vans, SUV's RV's, flatbeds, caravans and more.

• Features PMMA lens to provide excellent clarify and good UV resistance, sonic welded to ABS housing for water protection, withstand shock and vibration
• Uses LED diodes that last much longer than regular incandescent bulbs, stainless steel front screws
• 38 Ultra bright LED's (16) Red for stop/turn/tail functions, (18) white LED's for backup function and white LED's for license illuminator
• 3 stud mount design with 4-color coded wire connection for easy installation
• DOT compliant

User questions & answers

Question:	do these lights come with mounting brackets
Answer:	LED bulbs are made into tailight. Just mount and connect wires. Excellent product
Question:	Will this fit Chevrolet g-10 van
Answer:	There is two 1/4-20 studs sticking out of the housing. You can drill holes in a flat surface to match the light, insert the studs through the holes and tighten down with the supplied nuts.
Question:	I need the product l x h x w can someone tell me this please
Answer:	Yes, Trailers have tail lights along with 4 running lights on the sides. Two yellow lights located up forward on each side and two red lights located aft on each side. On the square light kit illustrated (normally used on boat and small utility trailers) the red panel on the side is the rear running light, has a bulb behind it and is reflective.
Question:	does this come with bulbs? if not what kind of bulbs are needed thank you
Answer:	NO, it comes with a non-conductive approximation of a ground wire, turns to powder as soon as you install. all the wiring in this kit are cheap crap and will fail in a short time. DO NOT BUY THIS CHEAP CRAP.

Product features

Complies With Federal Standards

Manufactured to comply with federal standards to ensure that these lights are road-worthy for visibility and reliability

Universal and Versatile

Designed for use on different vehicles such as trucks, flatbeds, cargo vans, boats, utility trailers, RVs, and more

38 Premium Quality LED's

Features ultra bright LEDs to cut through darkness & fog to provide visibility. Features 16 red LEDs, 18 white LEDs and 4 more to illuminate your license plate.

Quality Product

Made with PMMA lens for UV resistance, excellent clarity and abrasion resistance. Color coded wires for easy identification and installation

Complete Illumination

Includes 4 ultra bright white LEDs to illuminate your license plate

Durable and Reliable

We use stainless steel screws with quality lens and ABS frame for durability

Product description

TMH 2 Pcs 7.5" Surface Mount ( Flush Mount ) 10 LED Truck Tail Light , Side Led Marker Trailer Marker Lights, Led Tail Lights, Turn Signal light, Rear Lights, Truck & Trailer Brake Stop Lights, RV Light



Specification

Brand : TMH

Light Source : 10pcs F3 Piranha LED High Brightness

Material : PC Lens + ABS Housing

Light Color : Red

Light Dimension : 7.5" x3.3" x 1.0"

Fixing holes space : 7" x 2.7"

Wire Length: Approx. 8"

Wiring : Black = Negative , Red = Positive Tail Light , White = Positive Brake Light

Voltage: 12v DC

Suitable for most cars, SUVs, or trucks, trailers, tractors, semi-trailer, Dump, bus, boat, special vehicle,etc. For Heavy Duty trucks like Peterbilt, freightliner, international ,Kenworth, mack and lorries. Weatherproof ready for exterior mounting.

PLEASE make sure the size before purchasing.



Package Included

2 pcs Red Color 12V DC 10 LED Multi-Function Tail & Stop Light

8 pcs Screws sets



Applications

Indoor & Outdoor uses

Back up light

Off Road Lighting

Truck, Trailer Interior & Exterior Lighting

Construction Lighting

Boat Lighting

• Brand : TMH with 1 years Premium TMH warranty ( Free Replacement )
• ( Pack of 2 ) Red Light & Red Lens 2 Functions : Tail Light & Brake Light with 10 pcs Super Bright Piranha LED on each light
• High Quality Material with Ultrasonic Welding Process : Waterproof + Shock proof + Dust proof
• Work on 12v DC : 3 wires with 2 steps Brightness , Can Modify for Signal Light , Flash Light , Emergency Light ( Flasher relay or Controler not included )
• Surface Mount : Easy to install and wiring in minute , 4 screw included

User questions & answers

Question:	Where are these lights made
Answer:	Not sure I put them on a golf cart for running lights and they work fine for what I got them for
Question:	Are the mounting holes flush with the housing? I need to mount on my motorcycle fender
Answer:	Yes, there should be a clear lens installed on the light and a red lens included in the box.
Question:	what gage wire do they have
Answer:	So I did install a set of these exact lights in my son's 1997 wrangler.. got the wiring mixed up at first but did manage to get them working ... it took time and patience and a few errors and some trouble shoot.. all of which was my fault .. However unless you really did get a bad set ... they will work .. Sorry not a very good answer but that's all I got.... good luck hope you get them going my son loves his..
Question:	I am using these lights as temporary towing lights, brake, turn and taillights. Everything works but when i turn headlights on and your lights go out
Answer:	No they come as a set

• (Set of 2) Please check Amazon fitment NOTICE and OEM part number to make sure it fits your vehicle's rear turn signal lights or brake tail lights before purchasing. Chips: 39 pieces high quality, high power with high illumination led chips per 7440 7443 red led bulb ---360 degree full angle illumination with projector lens design
• Color: Brilliant pure red; Working Voltage: 12V~18V with built in IC driver for better working performance;
• Fitment: replace the bulb harness of 992,7440, 7440LL, 7440ST, 7441, 7443, 7443LL, 7443ST, 7444, 7444LL, W21W, W21/5W, 7443-SCK, 7443-SRCK, etc
• Application: Used for upgrading the incandescent T20 wedge W21W 7440 7443 brake light lamp, this bulb is compatible both Standard and CK/SRCK Type,safe and easy installation.
• Warranty: Fully ONE YEAR guaranteed for the manufacturer defect.please check the owner manual or Amazon fitment note for brake stop light or tail light application before purchasing.NOT canbus free, extra load resistors maybe required to avoid the error code or signal hyper flash.

User questions & answers

Question:	Does this fit a 2010 cadallic
Answer:	Depends on bulb size
Question:	i have acura rsx will it have hyperflash
Answer:	Almost assuredly, you'll have hyperflash. Firstly, LED bulbs weren't widely installed in 2006, so you have a low likelihood have having load resistors pre-installed. Secondly, Acura is made by Honda and my 2014 Honda needs load resistors to prevent hyperflash. It's not that big of a bother to install the load resistors. Just remember, you have to put a resistor in each position you put an LED bulb, but only for the turn signals.
Question:	Can I used for my 2016 Chevy Silverado brake and turning signal whitout resistor
Answer:	you can use it without a resistor but you will need a module (usually located under driver side dash). this led lights are not plug and play
Question:	Have a 2008 honda goldwing just wondering if they will work on the bike as well as a car
Answer:	Yes they will that work very well and bright

Product features

Comparison Between Stock Halogen lamp VS Alla Lighting Super Bright 2835-SMD T20 7440 7443 Red LED Bulbs as Turn Signal Light Brake Stop Tail Light

• Alla 2835-SMD 7443 led bulbs shows super bright pure red , yet the stock lamp shows dim yellowish red color
• Alla 2835-SMD 7443 led bulbs has much bigger difference between the high intensity and low intensity light output, about 1000 lumens for high intensity, and 200 lumens for the low intensity, yet for the stock lamp is about 350 lumens for the high intensity light output.
• Alla 2835-SMD LED 7443 bulb draws about 5.1W for high intensity yet the stock lamp draws about 28W, led bulbs draw much less current than stock lamps
• Alla 2835-SMD LED 7443 turn signal light makes your car more easily noticed while switching line by switching to the turn signal light,and also makes your car look much more luxury than stock lamp, more attractive.
• Alla 2835-SMD 7443 LED bulbs is 360° full angle degrees light output, the same light theory as the stock lamp for the best light performance.

Light Performance Comparison Between Alla Lighting Super Bright 2835-SMD W21W 7444 7441 7440 7443 Red LED Bulbs VS Original Lamp as Brake Stop Light

Specifications:

• Lumen:1000 Lumens/pc
• Working Voltage:12V-24V;
• Working Power:5.1W/PC for high intensity light output; 0.75W for low intensity light output, big difference between high and low intensity light output, easily noticed while braking at brake mode or blinkering at the turn signal mode.
• Working Current: 425MA for high intensity light; 63MA for low intensity light.
• Color: Brilliant pure red ( optional 6000K White and amber yellow are available) 
• Dimensions: 2.10(L) * 0.70(D)*0.35(H) Inch
• LED Type: High power and high illumination 2835 SMD

Features:

• More than triple brighter than stock dim halogen/incandescent 7443/7440 lamp
• Drawing much less current than stock lamps, low power consumption for longer lifespan
• Each bulb equips with 39 pieces high power,premium quality and high illumination 2835 SMD led chips
• Built in Intelligent IC driver for better stable current performance and heat dissipation for longer lifespan
• Fit any T20 wedge base, Cross reference number: 7440, 7441, 7442, 7443, W21W, WY21W,7443LL, 7440NA, etc
• NOT CANBUS error free type, For some vehicles, extra load resistors maybe required to avoid the error code or blinkering issue.

Application: Used for upgrading stock dim halogen/incandescent 7440/7441/7443 rear turn signal light, or brake stop tail light or center high-mounted stop light, or side marker light,etc.Package Includes: One pair ( 2 pieces) super bright 7443/7440 brilliant red 2835 39-SMD LED bulbsImportant Notice:

• Please check your owner manual or the stock lamp to confirm the correct bulb size (cross reference number) before purchasing, for Amazon fitment is not 100% accurate, it is only for reference.
• For some vehicles, extra load resistors maybe required to avoid the error code or blinkering issue.
• If you have any questions, or meet any issues of the order, please let us know directly by contacting seller under the order detail us(our working hour is 9:00AM-5:30PM PST), and we will help you solve the issue at the first time.

High Performance of Alla Lighting 7440 7443 Red LED Bulbs as Brake Stop Light

High Performance of Alla Lighting 7440 7443 Red LED Bulbs Turn Signal Light

360° Full Views Light Output of Alla Lighting 2835 SMD Red LED 7440 7443 Bulb

High Illumination of Alla Lighting 2835 SMD Red LED 7440 7443 Bulb

Product Dimension of Alla Lighting High Power 7440 7443 Red LED Lights Bulbs

Alla Lighting High Power 7440 7443 Red LED Lights Bulbs With Projector Lens

Directly plug T20 Socket of Alla Lighting 7440 7441 7444 7443 Red LED Bulbs

Product Features of Alla Lighting 7440 7441 7444NA 7443 Red LED Bulbs

Product description

This sale includes 4pc of 6" Red Oval Trailer Lights. waterproof submarine Includes 3-pin water tight plug with wires 10 LED super diodes for each light. Light is 2-5/16" x 6-7/16" oval, 1" thick (1.75" thick at wiring connection). Fits in a standard 2-1/2" x 6-3/4" oval hole. Light function: Stop, Turn, Tail Light These are 12 V lights. The lights are made from long lasting materials so you won't be left in a lurch! We are an American company and ship from a USA warehouse. Meets all applicable DOT/SAE standards and fits standard trailer light mount.

• Meets all applicable DOT/SAE standards and fit standard trailer light mounting position
• 10 LED super diodes for each light. grommet fits standard mounting position
• This sale includes 4pc of 6" Red Oval Trailer Lights. waterproof submarine Includes 3-pin water tight plug with wires
• the Light is 2-5/16" x 6-7/16" oval, 1" thick (1-3/4" thick at wiring connection). Fit in a standard 2-1/2" x 6-3/4" oval hole.

Product description

Fits: 88-99 Chevy / GMC C1500/C2500/C3500/K1500/K2500/K3500 Full Size Pickup

Fits: 92-94 Chevrolet Full Size Blazer

Fits: 94-99 Chevrolet Tahoe

Fits: 92-99 Chevrolet / GMC Suburban / Yukon

Fits: 99-00 Cadillac Escalade

High durability new material with UV and Abrasive coating to protect harmful sun light while provide long lasting light output performance

Complete set includes Left (Driver Side) and Right (Passenger Side)

CONDITION: Brand New In Original Packaging

High Quality Headlights made by OEM approved manufactureres with materials that meet or exceed strict OEM requirements.

Do not come with installation instructions and professional installation highly recommended.

• [Fit for] - 88-99 Chevy GMC C/K Fullsize Pickup Truck SUV
• [DOT & SAE] - Meets or Exceeds all Regulation in the U.S. & Canada
• [EZ Install] - Direct OEM Replacement No Modification Needed
• [New Aftermarket Part] - Completed Set, includes Both Driver(Left) & Passenger(Right) Side
• [Quality Assurance] - 30-Days Money Back Guarantee & 90 Days Limited Warranty

User questions & answers

Question:	Will I have to use a resistor for the reverse light
Answer:	This unit use standard incandescent bulb for reverse and you'll not need any resistor.
Question:	Can you remove the resistor if you already have the hyper flash relay installed
Answer:	Yes you can unclip it. I just left mine on. I also have a hyper flash relay with the resistor pack still on it. The lights work correctly still.
Question:	Is there a clear lens setup like this available
Answer:	We do offer clear lens but they are currently out of stock. Due to freight congestion, we are expecting new shipment to be available by the end of this Dec but may delay until Jan.
Question:	Does this fit a 1996 chevy silverdo
Answer:	It'll fit 1996 Silverado.

Product description

This bulb is compatible for both CK/SRCK and standard socket with Non-polarity design. Best value in the market!



Features

Dual Brightness: The Dim mode is Tail lights or DRL, while the Bright mode is Brake lights or Turn Signal lights. The bulb run in Bright mode when your bulb only function in one mode.

High Brightness LED: 54SMD 3014 chipset & 3SMD 3030 chipset.

Working Voltage: 9-30V (fit 12V, 24V vehicles).

Output Wattage: 3W/bulb (Low Power Consumption).

Color: Brilliant Red.

Waterproof: IP65.

Service Life: Up to 30,000 Hours.



Note: Load resistor or flash relay might be needed to prevent the hyper flash when replacement for Turn Signal Lights.



Warranty: iBrightstar Warranty for 1 year from date of purchase. Warranty type: Exchange or replacement.



IMPORTANT NOTICE! Please confirm the bulb base before placing an order.



iBrightstar is a registered brand with Amazon. Please contact us if there is any questions or other requests!Please check the bulb base before placing an order. If the customer order a wrong size it will cause doesnt fit their car. Since LED bulbs have no wattage with the stock bulbs and resulting in a smaller current when the car system detected the current smaller than before it will cause flasher to hyper flashing or created error. Requires a resistor or flash relay to prevent the hyper flash.

• (Set of 2 Bulbs)54SMD 3014 & 3SMD 3030 high brightness chips per bulb,Working Voltage:9v-30v,Size: 2.08"x 0.88" x 0.71"
• Fits: 3056 3057 3057K 3057LL 3155 3157 3157K 3157NA 3157NAK 3157LL 3156NA 3156A 3156 3156K 3357 3357K 3357KNA 3357LL 3457 3457-NA 3457K 3457NAK 3757AK 3757ALL 4057 4057LL 4057K 4114 4114LL 4114K 4157 4157LL 4157K 4157NA 4157NAK 5702A 5702AK 5702AK etc.Easy installation, plug and play.
• Application:Brake Lights,Tail Lights etc.Load resistor or flash relay might be needed to prevent the hyper flash when replacement for Turn Signal Lights.
• Advantage:Compatible for both CK/SRCK and Standard socket, non-polarity design.300% brighter than original halogen bulb, full Aluminum Housing with Projection lens for Maximum Light output and better heat distribution,built in Constant Current IC for Longer life span & Low Power Consumption.
• Please double check owners manual or original bulb number to confirm before placing an order. Any other problem please feel free to contact us, we are always here to satisfy of you.

User questions & answers

Question:	Do i need a relay for a 95 grand cherokee orvis
Answer:	Yes
Question:	Will these work on my 2016 chevrolet silverado 1500 front turn signal and marker light?how many lumens?6,000k?thank you for the help
Answer:	Based on the Amazon filter and my recollection of what type of standard bulbs your truck takes, yes these should work. As for the Lumen rating, I don't know, but these are much brighter than the standard 3057 that most vehicles come with. Keep in mind, that if you install these, you might get the "hyper-flash" which is rapid flashing and it may cause a light-out fault. To eliminate this, you will need to add a resistor to each light you add.
Question:	How bright at these bulbs in lumens
Answer:	4 times as bright as a filament bulb if not brighter they will definitely see your lights very good upgrade I've been using them in my 4X4 nissan truck for 5 years and put them in my harley and my F350 dually youll be happy you got them installed just no comparison to filament bulbs it like Daytime,,,, verses Night.
Question:	Would this fit a 2005 Subaru Forester
Answer:	check the number on your existing bulb, these lights work great and are really bright.