14 best clear epoxy resin uv resistant

Product description

Clear Epoxy Resin Art Resin Epoxy 1 Gallon Kit

• Premium epoxy kit - Aquaseal epoxy resin and hardener kit delivers extra durable results ideal for boat building, composite construction, house repairs, table top epoxy resin projects and more!
• All you need included - Aquaseal marine epoxy resin kit includes : resin half gallon bottle, hardener half gallon bottle , 2x measuring cups, 2x plastic spreader and 2x plastic stirrers. Everything you need to start your clear epoxy projects.
• Easy to use - Mix 1 part epoxy resin and 1 part hardener for 20 minutes of work time on your marine epoxy projects. Use on wood, fiberglass, reinforcement fabrics, etched aluminum, bare steel, and lead.
• Faster curing and harder - Strong, clear epoxy resin, fully UV-resistant cures faster and harder, ideal durability for boat repair, table top epoxy and countertop epoxy projects.
• Customer service - Please read the instructions provided with the Aquaseal marine epoxy before use. If you have any questions or issues, please don’t hesitate to send the seller a message through Amazon and we will respond within 24 hours.

• ✔ CRYSTAL CLEAR - Our Table Top Epoxy cures ultra clear making it perfect for table tops, bar tops, and countertops
• ✔ UV RESISTANT - Unlike many other epoxies, our epoxy resist yellowing caused from exposure to Ultra Violet Light Sources
• ✔ SELF LEVELING - Bar Top Epoxy self levels on application including corners, over bar rails and edges.
• ✔ HIGH GLOSS DURABLE FINISH - Epoxy resin leaves durable, blemish resistant, water resistant and impact resistant coating
• ✔ 100% SOLIDS - Low Odor, ZERO VOC, consistent thickness, quick curing 1 to 1 mixture, 1 Gallon Kit

User questions & answers

Question:	Is it required to use a ventilator mask when using? and is this Resin food safe
Answer:	It is not required. However, you should use the epoxy in a well-ventilated area. It is possible to be food safe. However, because the customer is mixing/pouring we cannot say this is food safe. Each mixture/application would have to be assessed individually.
Question:	Id like to dye the epoxy different shades of green but I need it to stay transparent. Any suggestions
Answer:	There are various dyes and pigments to choose from. It really depends on how deep of a green you'd like while maintaining transparency. I would suggest trying multiple on a sample area so that you can gauge the color/transparency of the pigment/dye.
Question:	I have stained my bar top with an oil based stain. Can I use the epoxy over it or do I need to do some other prep
Answer:	You can use a water-based clear coat on top of the stain. After the clear coat has cured, use a 320grit sand paper to take the shine off. You can then apply the table top epoxy.
Question:	What’s the diameter of the cap? I want to buy pumps to fit, thanks
Answer:	The cap is 1.5 inches in diameter. Let us know if you have any other questions. Thanks!
Question:	How much does it discover ( sq feet
Answer:	Covers apx 750 sq inches.
Question:	I have a heavy marble table, the bottom mount under the top broke off, would it be strong enough for this application
Answer:	I got a job to put together a 13 foot marble altar, weighing several tons. I used this stuff to glue the hundreds of marble pieces together, after testing the bond strength, and it's still standing today. Granted there isn't any real strain on the joints in most places, but the bond is stronger than the marble itself. This is good stuff.
Question:	Can it fix on the cracks of corina counter top
Answer:	Hi Chris,It is great for crack repair as long as the crack is wide enough to be able to get the material down in it. A good rule of thumb is that crack needs to be wide enough to get a credit card wedged between. Good luck!
Question:	What type of colorant can be used with the product - is the resin considered a polyester resin. The product details are not very precise
Answer:	For coloring the resin I have used Custom 4 Coloring Kit for Epoxy Gluing or Repairing of Granite,...Sold by: GRANITE POLISHING PADSYou can order this item from amazon. The dye is very efficient and seems to work very well with the resin. Yes this epoxy appears to be some sort of polyester. As soon as u add the hardener the epoxy hardens fast but it gives you enough time work with. My results were very good although didn't polished it yet. Good luck

Product features

Crystal Clear Finish

High gloss, ultra clear finish makes our epoxy perfect for Table Tops, Bars Tops, Coffee Tables, Live Edge Tables and other coating applications. However, epoxy is not flexible. River tables must be supported to prevent flexing which could cause cracking.

*Do not pour over oil-based paint or stain.

Common Question: My project is painted or stained with an oil based product, what can I do?

A: You can apply a water based clear coat (must be water based). Once the water based clear coat has fully cured, you can apply the epoxy. If the clear coat leaves a shine/gloss you may want to scuff the surface to ensure the epoxy properly sticks. We recommend using 320 grit sandpaper. If you do sand, be sure to thoroughly clean the surface prior to applying the epoxy. We recommend using Isopropyl Alcohol 99% (be sure it is 99%) to clean.

UV Resistant

Although most epoxies will yellow over time, some resist yellowing caused by exposure to ultraviolet light better than others. Our epoxy contains UV Inhibitors which helps to resist yellowing. *Although our epoxy is UV resistant, which resists yellowing, we do not recommend leaving finished projects in direct sunlight or for permanent outdoor applications.

Common Question: Can I use this on a table that will be outside on a covered patio?

A: It is possible to leave the epoxy outdoors if not exposed to direct UV exposure. If the epoxy is exposed to direct UV, the epoxy can yellow. This will be more noticeable on white or lightly colored substrates/surface. We recommend exercising caution when considering use over white or light-colored surfaces.

It is also important to consider temperature fluctuations. Materials such as metal and glass can expand and contract at a different rate from the epoxy. This could cause glass to crack or the epoxy to peel away from a metal surface.

Food Safe Epoxy

Properly cured epoxy is possible to be food safe. However, because the customer is mixing/pouring we cannot say this is food safe approved. Each mixture/application would have to be assessed individually. This is not a high heat epoxy. We recommend using hot pads/coasters for coffee mugs, hot pans, pots, etc.

Common Question: Can I use this epoxy to make tumblers?

A: We have many customers using our epoxy for custom tumbler designs. However, this epoxy self levels. Therefore, many customers utilize a "cuptisserie" which is a rotating device that keeps the tumbler rotating while the epoxy is curing so that the finish is even.

Again, keep in mind: Properly cured epoxy is possible to be food safe. However, because the customer is mixing/pouring we cannot say this is food safe approved. Each mixture/application would have to be assessed individually.

Colored Epoxy Compatible

How To Color Epoxy: Our epoxy mixes well with mica pigment powders for colored epoxy applications. River tables, resin art canvas and more may require tinted epoxy. Epoxy is not meant to be mixed with or poured over oil-based products. Do not pour over oil-based paint or stain.

Common Question: What type of pigment or dye should I use with this epoxy.

A: We do not recommend mixing epoxy with paint or anything oil based. Many of our customers use mica pigment powders. Mica pigment powders come in many different colors, glitters, metallics, and even glow in the dark.

Q: How Much Pigment Powder Should I Use?

A: This is a subjective answer as it depends on the certain hue and level of opacity desired. We suggest starting with a very small amount and adding more until the desired color is achieved. We also always suggest testing a small scrap piece of material to understand how the epoxy will flow and how the color will cure in the epoxy.

Easy To Use 1:1 By Volume Mixture

Self Leveling, Impact Resistant, Superior Air Release

Popular uses include wooden bar tops, river tables, embedding pictures or embedding solid objects into a desired surface. Because our epoxy cures crystal clear, multiple layers will not compromise color/transparency. Each poured layer should not exceed 1/4" at a time. Working Time: 25 (+/-5 Minutes)

How Much Epoxy Do I Need?

Our rule of thumb regarding coverage is 12 sqft per mixed gallon at 1/8 inch.

Family Owned Business, Made In USA

VARIETY OF APPLICATIONS

For Uses On

• Wood
• Concrete
• Bottle Caps
• Artwork
• Canvas

Common Question: Can I apply epoxy over paper products like photographs, cigar wrappers, playing cards, and more?

A: If you wish to apply paper decals, bottle caps, or other objects under the Table Top surface, those objects need to be bonded to the surface with craft glue or a thin layer of Table Top Epoxy. Paper products must be sealed prior to applying any epoxy as the epoxy could soak in and ruin the paper product.

You can use something like mod podge or a similar water based clear coat/glue. Allow this seal coat to dry thoroughly before applying epoxy. For figurines, shells, and other large more three-dimensional items, using a thin epoxy seal coat is best, prior to encapsulating.

HIGH GLOSS FINISH

Epoxy resin leaves durable, blemish resistant, water resistant and impact resistant coating.

The beauty of epoxy is the ability to recoat a surface after years of use to regain a smooth, high gloss finish.

Common Question: I see that your epoxy requires thin pours of no more than 1/4" per application. How long do I need to wait between pouring a new layer?

You can apply the second coat when the prior coat is tacky to the touch (usually 4-6 hours depending on temperature). If you wait longer than 12 hours between coats, we recommend a light sanding. You can use 320 grit to scuff the surface. This will help the next coat to properly stick. If you do sand, be sure to thoroughly clean the surface prior to pouring the flood coat. We recommend using Isopropyl Alcohol 99% (make sure it is 99%) to clean.

TOP QUALITY

Incredible Solutions Table Top Epoxy is proudly MADE IN THE USA.

Competent Knowledge Base helps plan and troubleshoot even the most complicated projects.

Common Question: Does your epoxy require specific temperature environment to mix/pour epoxy?

A: The ideal working temperature is around 77°F. Best results can be obtained at temperatures between 75°F and 85°F, in a clean, dry, dust-free environment. Avoid working in high humidity. It is important you keep your project in this environment throughout the entire curing process. We recommend using this product on a leveled and flat work surface so that it can flow and self-level properly.

• ✅ BEAUTIFUL RESULT: Designed to look gorgeous, strong and durable. crystal clear epoxy, amazing clear cast , deep pour. Craft Resin increases the attractiveness and value of whatever it's used on!
• ✅ ALL IN ONE KIT: This kit will give you everything you need to get started with Craft Resin - 500ml/17Oz epoxy resin and 500ml/17Oz hardener; reusable mixing stick and gloves
• ✅ CRYSTAL CLEAR: Cures clear to a glass-like finish.
• ✅ EASY TO USE: Craft Resin is self-leveling, its 1:1 mixing ratio, simply mix two part epoxy: resin and hardener by volume.
• ✅ SAFE: Craft Resin is UV resistant, Food safe, Non-toxic. No VOCs. No solvents. Odorless. Non-flammable. Non-hazardous

User questions & answers

Question:	Can this be used for a door sign
Answer:	Depends on what kind of door sign you are making, I suppose! You could layer resin over a wood sign, you could mold a sign from the resin, etc.
Question:	Can you use this to glue broken ceramic together
Answer:	Super glue or glass glue would be better
Question:	Can this be used on a mosaic tile table top that has a rim around it
Answer:	Yes. This will work on your table top. Just read the directions & follow them to the "T". This resin works very well but the directions have to be followed closely. Good luck & have fun.
Question:	How long is the work time? How long does it typically take before the resin gets tacky
Answer:	Gets tacky about 25 to 35 minutes after you have mixed the 2 parts. Not to say it isnt applyable. That takes...maybe 50 minutes before signs of firming. Should not be messed with at that point. Prepare ahead of time!

• ✔ CRYSTAL CLEAR EPOXY RESIN- Cures Ultra Clear For Superior, Smooth Glossy Finish
• ✔ UV Resistant- Enhanced UV PRO Resistance Formula Helps Resist Yellowing Caused By Exposure To Ultraviolet Light
• ✔ EASY TO USE- 1:1 By Volume Mixture, 100 Solids, Low Odor, Direction For Use Pamphlet Included
• ✔ SELF LEVELING - Perfect For Bar Tops, Table Tops, Live Edges, Bar Rails & Countertops
• ✔ DURABLE FINISH- Impact Resistant, Waterproof When Cured, Resist Scratches & Blemishes

User questions & answers

Question:	Is it FDA approved
Answer:	Yes! A hairdryer is ok, but it is best to use a heat gun.
Question:	Can you use this product in molds for a solid project like a clear paper weight
Answer:	Same for me. The QR code on the flyer does not work and no response with I set the number listed. Just want to receive my free pigments and powders.
Question:	Do you recommend this product or crystal clear naked fusion for outdoor bar cover
Answer:	Don’t know. I use under dish plates etc
Question:	My product has a coat of water-based primer. Can I apply the epoxy to this
Answer:	We use them on a glass table and they work great.

Product features

Crystal Clear Finish

High gloss, ultra clear finish makes our epoxy perfect for Table Tops, Bars Tops, Coffee Tables, Live Edge Tables and other coating applications. However, epoxy is not flexible. River tables must be supported to prevent flexing which could cause cracking.

*Do not pour over oil-based paint or stain.

Common Question: My project is painted or stained with an oil based product, what can I do?

A: You can apply a water based clear coat (must be water based). Once the water based clear coat has fully cured, you can apply the epoxy. If the clear coat leaves a shine/gloss you may want to scuff the surface to ensure the epoxy properly sticks. We recommend using 320 grit sandpaper. If you do sand, be sure to thoroughly clean the surface prior to applying the epoxy. We recommend using Isopropyl Alcohol 99% (be sure it is 99%) to clean.

UV Resistant

Although most epoxies will yellow over time, some resist yellowing caused by exposure to ultraviolet light better than others. Our epoxy contains UV Inhibitors which helps to resist yellowing. *Although our epoxy is UV resistant, which resists yellowing, we do not recommend leaving finished projects in direct sunlight or for permanent outdoor applications.

Common Question: Can I use this on a table that will be outside on a covered patio?

A: It is possible to leave the epoxy outdoors if not exposed to direct UV exposure. If the epoxy is exposed to direct UV, the epoxy can yellow. This will be more noticeable on white or lightly colored substrates/surface. We recommend exercising caution when considering use over white or light-colored surfaces.

It is also important to consider temperature fluctuations. Materials such as metal and glass can expand and contract at a different rate from the epoxy. This could cause glass to crack or the epoxy to peel away from a metal surface.

Food Safe Epoxy

Properly cured epoxy is possible to be food safe. However, because the customer is mixing/pouring we cannot say this is food safe approved. Each mixture/application would have to be assessed individually. This is not a high heat epoxy. We recommend using hot pads/coasters for coffee mugs, hot pans, pots, etc.

Common Question: Can I use this epoxy to make tumblers?

A: We have many customers using our epoxy for custom tumbler designs. However, this epoxy self levels. Therefore, many customers utilize a "cuptisserie" which is a rotating device that keeps the tumbler rotating while the epoxy is curing so that the finish is even.

Again, keep in mind: Properly cured epoxy is possible to be food safe. However, because the customer is mixing/pouring we cannot say this is food safe approved. Each mixture/application would have to be assessed individually.

Colored Epoxy Compatible

How To Color Epoxy: Our epoxy mixes well with mica pigment powders for colored epoxy applications. River tables, resin art canvas and more may require tinted epoxy. Epoxy is not meant to be mixed with or poured over oil-based products. Do not pour over oil-based paint or stain.

Common Question: What type of pigment or dye should I use with this epoxy.

A: We do not recommend mixing epoxy with paint or anything oil based. Many of our customers use mica pigment powders. Mica pigment powders come in many different colors, glitters, metallics, and even glow in the dark.

Q: How Much Pigment Powder Should I Use?

A: This is a subjective answer as it depends on the certain hue and level of opacity desired. We suggest starting with a very small amount and adding more until the desired color is achieved. We also always suggest testing a small scrap piece of material to understand how the epoxy will flow and how the color will cure in the epoxy.

Easy To Use 1:1 By Volume Mixture

Self Leveling, Impact Resistant, Superior Air Release

Popular uses include wooden bar tops, river tables, embedding pictures or embedding solid objects into a desired surface. Because our epoxy cures crystal clear, multiple layers will not compromise color/transparency. Each poured layer should not exceed 1/4" at a time. Working Time: 25 (+/-5 Minutes)

How Much Epoxy Do I Need?

Our rule of thumb regarding coverage is 12 sqft per mixed gallon at 1/8 inch.

Family Owned Business, Made In USA

VARIETY OF APPLICATIONS

For Uses On

• Wood
• Concrete
• Bottle Caps
• Artwork
• Canvas

Common Question: Can I apply epoxy over paper products like photographs, cigar wrappers, playing cards, and more?

A: If you wish to apply paper decals, bottle caps, or other objects under the Table Top surface, those objects need to be bonded to the surface with craft glue or a thin layer of Table Top Epoxy. Paper products must be sealed prior to applying any epoxy as the epoxy could soak in and ruin the paper product.

You can use something like mod podge or a similar water based clear coat/glue. Allow this seal coat to dry thoroughly before applying epoxy. For figurines, shells, and other large more three-dimensional items, using a thin epoxy seal coat is best, prior to encapsulating.

HIGH GLOSS FINISH

Epoxy resin leaves durable, blemish resistant, water resistant and impact resistant coating.

The beauty of epoxy is the ability to recoat a surface after years of use to regain a smooth, high gloss finish.

Common Question: I see that your epoxy requires thin pours of no more than 1/4" per application. How long do I need to wait between pouring a new layer?

You can apply the second coat when the prior coat is tacky to the touch (usually 4-6 hours depending on temperature). If you wait longer than 12 hours between coats, we recommend a light sanding. You can use 320 grit to scuff the surface. This will help the next coat to properly stick. If you do sand, be sure to thoroughly clean the surface prior to pouring the flood coat. We recommend using Isopropyl Alcohol 99% (make sure it is 99%) to clean.

TOP QUALITY

Incredible Solutions Table Top Epoxy is proudly MADE IN THE USA.

Competent Knowledge Base helps plan and troubleshoot even the most complicated projects.

Common Question: Does your epoxy require specific temperature environment to mix/pour epoxy?

A: The ideal working temperature is around 77°F. Best results can be obtained at temperatures between 75°F and 85°F, in a clean, dry, dust-free environment. Avoid working in high humidity. It is important you keep your project in this environment throughout the entire curing process. We recommend using this product on a leveled and flat work surface so that it can flow and self-level properly.

User questions & answers

Question:	will sealing bare wood surface prevent bubbles forming
Answer:	The product should be applied in two stages. The first stage is referred to as the seal coat. The seal coat is a small batch of epoxy that is brushed on in a thin layer to seal any pores in the surface and prevent air bubbles from forming in the following flood coat. Our epoxy is used for both your seal coat and your flood coat.
Question:	Is this FDA compliant
Answer:	Yes, here is the response from promarine supplies "Although we do not have FDA approval certificate, our epoxy does comply with FDA Compliant Coating for Direct and Indirect Food Contact. Our Epoxy is VOC-Free and user-friendly. Once the epoxy is cured, it is an inert plastic that is non-harmful or hazardous." I have also shared some information from our websites in the link below. https://promarinesupplies.zendesk.com/hc/en-us/articles/115001444873-Is-Pro-Marine-Clear-Table-Top-Epoxy-FDA-Compliant-or-Food-Safe- https://www.promarinesupplies.com/www.promarinesupplies.com/blogis-pro-marine-supplies-epoxy-food-safe/
Question:	Will this work over Minwax polyurethane (oil based). i see it wont react well with oil based stain so i applied poly over the stain. thoughts
Answer:	epoxy can go over them in about 24 hours. OIL BASED paints take a LONG time to fully dry. If an oil-based paint is used, you must apply 3 coats of oil-based polyurethane to seal the surface before applying a seal coat of our UltraClear epoxy. If you go directly over the oil-based paint and it is not completely dry, you run the risk of the epoxy not sticking to the surface and peeling off months later.
Question:	how many square feet does it cover
Answer:	it depends on how thick you put it. First time I used it, 1 gallon for 80 square feet. second time I used 5 oz thinner to 1/2 gallon and covered 80 square feet.it all depends how thick you spread it.

Product features

High Gloss & Durable

High performance and Crystal clear! Produces a tough, high gloss, water and scratch resistant coating.

Versatile

Can be used for a wide variety of applications, art, and home projects.

Food Safe

Food Safe formula for artistic items used around food, such as trays, tumblers, and glassware.

Easy 1:1 Self Leveling Formula

Use our product with ease, featuring an easy 1:1 self-leveling formula!

Beautiful and Versatile, Crystal Clear Finish...Every Single Time!

Step 1: Measure

Pour equal parts of resin and hardener into a clean mixing container or graduated mixing tubs, using a 1:1 ratio (by volume) It is crucial that the product is measured accurately and mixed thoroughly. Measure 1 part RESIN to 1 part HARDENER by volume. Do NOT vary this ratio. Our Epoxy is formulated to cure at a specific mixing proportion, and any variances can cause the product never fully to cure. We recommend always pouring the HARDENER into your mixing container first, followed by the RESIN. This will help the two components mix thoroughly.

Step 2: Mix

First Mix: Mix with a flat bottom stir stick or spatula being sure to scrape the sides and bottom of the container as you go. Your mixture will appear hazy at first, and then become more transparent as the resin and hardener molecules begin to blend within three to five minutes.

Second Mix: Pour the Resin and Hardener from your first container into a second container scraping all the mixture out from the sides and bottom of the cup. Thoroughly mix for an additional three minutes.

Step 3: Seal Coat Stage

The best way to apply a seal coat is to start on one end of the table and pour the resin all the length of the surface, zigzagging as you go. Then use a foam brush to drag the resin across the entire surface to achieve an even coat. The epoxy cures rather quickly in the container, so it is necessary to paint the seal coat on quickly or mix up a smaller amount so that it does not cure in the container while you are still working on it. The seal coat does not need to be smooth as the flood coat will fill in the brush strokes and irregularities making it crystal clear. Once the entire surface is sealed, wait 4-6 hours to pour the flood coat. Do not exceed 10 hours or you run the risk of the flood coat not blending into the seal coat flawlessly.

Step 4: Flood Coat Stage

Each flood coat self-levels at approximately 1/8” thick. If depths thicker than 1/8” are desired multiple coats are necessary. You must wait at least 4 to 10 hours between flood coats. The epoxy will still be tacky so the next pour will stick to it.

The best way to apply the flood coat is to start on one end and pour the resin the entire length of the surface, zigzagging as you go. After you are finished pouring, set the container down. Do NOT try to scrape anything else out of the bucket. Because you are pouring about three times the amount of product you did with the seal coat, the material will immediately start to flow out.

Step 5: Remove Air Bubbles

Once you have sufficiently covered the entire surface with your flood coat, you will begin the process of popping air bubbles. The best tool for removing bubbles is a small propane torch. Hold the flame approximately 6 to 10 inches away from the table top and quickly sweep across the entire surface using an ironing motion. You will immediately see the bubbles start to pop. Do this until all the bubbles are gone from the surface of your table.

* After pouring your epoxy, it is common for air bubbles to form. Bubbles can continue to develop for up to 60 minutes after the curing process has begun. The most efficient way to get rid of them is to run a blowtorch over the surface sporadically 10 - 15 min at a time.

Step 6: Curing Process

After applying your final coat, the product should be kept in a clean, dust-free environment at a minimum of 75-80° F degrees. The product takes approximately 12-14 hours to dry to the touch. However, the product should not be put into any use for at least three days which will allow it to achieve sufficient hardness to resist scratching. At temperatures below 75 F, the product will take longer to cure and might not cure to complete hardness.

• Designed for Table Tops, Bars, Wood finishes, See-Through Encapsulations, Art work, and other applications
• Self Leveling and High Gloss U.V. Resistant Formula
• Produces a Tough, High Gloss, Water Resistant Coating
• Eliminates Craters, Crawling and Fish Eyes
• Blush Resistant

User questions & answers

Question:	I ran out in the middle of a project. Next batch wont arrive until after the 12 hour window for multiple coats. Should I just sand before next coat
Answer:	Yes, lightly sand to help your next coat adhere better to the last one.
Question:	I have wood table that I want to make shine, would this product will give me what I'm looking for
Answer:	Yes it will make the table very glossy but it is not an easy process . If you have not worked with epoxy much you will want to practice before you use it on your table.
Question:	What are the instructions for installation? Other answer says practice first, but I'm wondering what possible complications might be
Answer:	Possible complications we found is not mixing this properly therefore it will not harden.
Question:	Is there a recommended maximum depth for this
Answer:	1/8 normal. I have done 2 inch at time but you really need deep pour product for river table.

Product features

High Gloss & Durable

High performance and Crystal clear! Produces a tough, high gloss, water and scratch resistant coating.

Versatile

Can be used for a wide variety of applications, art, and home projects.

FDA Compliant

FDA Compliant formula for artistic items used around food, such as trays, tumblers, and glassware.

Easy 1:1 Self-Leveling Formula

Use our product with ease, featuring an easy 1:1 self-leveling formula!

Beautiful and Versatile, Crystal Clear Finish...Every Single Time!

Step 1: Measure

Pour equal parts of resin and hardener into a clean mixing container or graduated mixing tubs, using a 1:1 ratio (by volume) It is crucial that the product is measured accurately and mixed thoroughly. Measure 1 part RESIN to 1 part HARDENER by volume. Do NOT vary this ratio. Our Epoxy is formulated to cure at a specific mixing proportion, and any variances can cause the product never fully to cure. We recommend always pouring the HARDENER into your mixing container first, followed by the RESIN. This will help the two components mix thoroughly.

Step 2: Mix

First Mix: Mix with a flat bottom stir stick or spatula being sure to scrape the sides and bottom of the container as you go. Your mixture will appear hazy at first, and then become more transparent as the resin and hardener molecules begin to blend within three to five minutes.

Second Mix: Pour the Resin and Hardener from your first container into a second container scraping all the mixture out from the sides and bottom of the cup. Thoroughly mix for an additional three minutes.

Step 3: Seal Coat Stage

The best way to apply a seal coat is to start on one end of the table and pour the resin all the length of the surface, zigzagging as you go. Then use a foam brush to drag the resin across the entire surface to achieve an even coat. The epoxy cures rather quickly in the container, so it is necessary to paint the seal coat on quickly or mix up a smaller amount so that it does not cure in the container while you are still working on it. The seal coat does not need to be smooth as the flood coat will fill in the brush strokes and irregularities making it crystal clear. Once the entire surface is sealed, wait 4-6 hours to pour the flood coat. Do not exceed 10 hours or you run the risk of the flood coat not blending into the seal coat flawlessly.

Step 4: Flood Coat Stage

Each flood coat self-levels at approximately 1/8” thick. If depths thicker than 1/8” are desired multiple coats are necessary. You must wait at least 4 to 10 hours between flood coats. The epoxy will still be tacky so the next pour will stick to it.

The best way to apply the flood coat is to start on one end and pour the resin the entire length of the surface, zigzagging as you go. After you are finished pouring, set the container down. Do NOT try to scrape anything else out of the bucket. Because you are pouring about three times the amount of product you did with the seal coat, the material will immediately start to flow out.

Step 5: Remove Air Bubbles

Once you have sufficiently covered the entire surface with your flood coat, you will begin the process of popping air bubbles. The best tool for removing bubbles is a small propane torch. Hold the flame approximately 6 to 10 inches away from the table top and quickly sweep across the entire surface using an ironing motion. You will immediately see the bubbles start to pop. Do this until all the bubbles are gone from the surface of your table.

* After pouring your epoxy, it is common for air bubbles to form. Bubbles can continue to develop for up to 60 minutes after the curing process has begun. The most efficient way to get rid of them is to run a blowtorch over the surface sporadically 10 - 15 min at a time.

Step 6: Curing Process

After applying your final coat, the product should be kept in a clean, dust-free environment at a minimum of 75-80° F degrees. The product takes approximately 12-14 hours to dry to the touch. However, the product should not be put into any use for at least three days which will allow it to achieve sufficient hardness to resist scratching. At temperatures below 75 F, the product will take longer to cure and might not cure to complete hardness.

Product description

Looking for a clear resin that is perfect for coating artwork, tables and making jewelry? Well you found the best! This resin is crystal clear. Contains UV absorbers and hals (hindered amine light stabilizers). What does this mean? This resin resists yellowing and will remain clear even under direct sunlight. This product cures to a super high gloss shiny finish. Clearcast 7050 has a long work time with a rigid finish makes this resin ideal for all decorative applications. 45-60 minute work time with a 24 hour cure. This product is best suited for thin coatings. Avoid large pours with this resin. For castings, stay under 1/4".

User questions & answers

Question:	Is this food grade safe want to use it on tumblers and plates
Answer:	It depends on the project. If you could be more specific, plane of glass, a glass handle cup, stain glass project etc.
Question:	I've been coating photos & art with artresin...very expensive. will clearcast work as well for a glossy finish? which whould i try: 7000 or 7050? why
Answer:	Hello, Gorilla Super Glue Gel will work on most plastics, however, it will not adhere to polyethylene or polypropylene type plastics. If we can be of further assistance, please contact our Consumer Affairs team at 800-966-3458 or through our website at www.gorillatough.com/contact and reference case #268648. Thank you, The Gorilla Glue Company
Question:	what is the recommended application temperature range
Answer:	I would use the original waterproof.
Question:	Hi, would this product work well as far as embedding objects in my castings like charms, insects, watch parts, etc. Castings would be 1 inch or less
Answer:	Hello, Once opened, the useful life can vary depending upon environmental factors. For further assistance, please contact our Consumer Affairs team at 800-966-3458 or through our website at www.gorillatough.com/contact and reference case #191776. Thank you, The Gorilla Glue Company
Question:	What is the size of the clips
Answer:	One of the ways we used it was on an outdoor thermometer, outdoor table and a piece that broke off a patio chair. They've all been rained on several times and have been in very cold and very hot temps and so far, the glue has held without having to reapply.
Question:	Are they microwave safe? I need something to keep an an egg cooker sealed shut
Answer:	Well, I have used it on submerged items in my freshwater aquarium containing guppies, neons, and snails and never had a problem.
Question:	How long are these clips
Answer:	If it's a small blind and window I quite sure it will. My husband glued the hood ornament back onto his car and it holds like concrete. He also used it to hold his outer mirror casing on the car and it holds beautifuls. I hope this gave you some helpful hints.
Question:	Are these big enough and sturdy enough to use in freezer for French fry and vegetable bags
Answer:	Apply just a very few small droplets of glue about 3/4" apart from each other and not to close to the edges of the handle (the glue will really spread-out if both surfaces are really smooth). Do not "spread or smear" the glue around with the applicator tip when applying it as this may cause air bubbles which, when under compression (like when you firmly hold the two pieces together for 60 seconds to secure the bond) that will greatly decrease the strength of the bond! Application of too much glue will also cause the glue to ooze out around the handle (if it does this DO NOT try and wipe it off. Let it harden for a day or two and then carefully cut away the excess glue with a razor blade). Whenever using any "Super Glue" always remember that the "thinner" the bond the stronger it will be. Too much glue will create a weaker bond due to the fact that shear stresses (like when you are pulling on the handle, lets say) will eventually stretch the thicker glue creating micro-fractures which, over a period of time and repeated stresses and increasing fracturing, will finally fatigue the bonding agent (glue), and the bond will fail. Remember the old adage, "Too much of anything is not always a good thing". I wish you great success.Lee

• Designed for Table Tops, Bars, Wood finishes, See-Through Encapsulations, Art work, and other applications
• Self Leveling and High Gloss U.V. Resistant Formula
• Produces a Tough, High Gloss, Water Resistant Coating
• Eliminates Craters, Crawling and Fish Eyes
• Blush Resistant. A total of 2 quarts combined.

User questions & answers

Question:	how do you apply this product to an outdoor table
Answer:	I assume you are talking about a table located outside and it cannot be brought inside for coating. In theory the system will work outside just like inside providing the temperature is sufficiently high. The instructions say 75F minimum. I have success at 65F in my garage here in South Carolina during winter months. If I were doing this outside I would follow a process something like this. 1. Make sure the table is dry. No rain or precipitation for several days. 2. Temperature planned to be above 65F for 3 to 4 days/nights. Higher temperature is better. 3. I would cover the ground under the table with plastic and weight the plastic down so it seals the moisture in the soil so it does not rise when applying the coating. 4. Level the table as best you can. The epoxy will run to the low side if it is not level. 5. I would build a frame to hold plastic sheet that will completely cover the table without touching the table. This should be open at the bottom by 1 to 1.5 feet so the air circulates and moisture does not accumulate. End vents in the plastic would be useful also. 6. The day I plan to apply the coating I would wash the table with denatured alcohol and let it dry. This wipe again with the alcohol. Follow this with heating of the surface with a heat gun. 7. Mix and apply the epoxy per the directions. Use the heat gun to remove "air" bubbles from the surface as described in the instructions. 8. Once heating is no longer being performed cover the table with the plastic frame. 9. Come back in 6 to 8 hours and evaluate the coating. If bugs are present remove them before applying next coating. 10. When ready to apply the 2nd coating wipe clean with denatured alcohol and dry with heat gun. then mix epoxy and apply per instructions. Repeat air bubble removal and cover with the frame. 11. Repeat for any additional layers. To get good leveling the epoxy needs to be at a high enough temperature for the mixed viscosity to be low enough to flow. But if the temperature is too high it will start to cure too quickly, this is why the instructions say to pour out the epoxy once it is mixed so the temperature will not rise in the container. (The curing reactions is exothermic.) I hope this helps.
Question:	Could i use this to cover a wallpapered desk top
Answer:	Yes but you must seal the paper on all side top and bottom before pouring. I used multiple layers of modge podge. But I'm sure there is other products that would work too.
Question:	can this be poured in silicone moulds, like for making coasters
Answer:	Yes, it can be poured in molds, makes lovely coasters!
Question:	Whats the work time
Answer:	Including mixing and initial pour the approximate total work time is 25 minutes.

Product features

Beautiful and Versatile, Crystal Clear Finish...Every Single Time!

High Gloss & Durable

High performance and Crystal clear! Produces a tough, high gloss, water and scratch resistant coating.

Versatile

Can be used for a wide variety of applications, art, and home projects.

Food Safe

Food Safe formula for artistic items used around food, such as trays, tumblers, and glassware.

Easy 1:1 Self Leveling Formula

Use our product with ease, featuring an easy 1:1 self-leveling formula!

• ✅ CHEMICALLY TOUGHER THAN A DIAMOND - MAMAR Epoxy Resin Plus is a high-performance UV resistant coating formulated specifically for art and DIY projects. Our special craft resin is ultra-glossy, crystal clear, scratch resistant, non-flammable, free of toxins, odors, VOCs, and bubbles. It eliminates craters, crawling, and fish eyes.
• ✅ GLISTENING FINISH - Unlike anything else currently on the market, our patented resin mix is very low in viscosity and provides an ultra gloss finish making it one of the easiest brands to work with. Enjoy a glistening finish on wooden table tops, artwork, or any other surface in need of durability, extra strength, and water protection that will last for years to come. Envelope your valuable project with a rock hard tough shell.
• ✅ PERFECT FOR DIY, CRAFTS, & MORE - This crystal clear epoxy resin kit formula comes with both parts: 1 gallon of resin and 1 gallon of hardener and has a simple mixing ratio of 1:1. Perfect for table tops, bars, wood finishes, sculptures, art work, and many other applications. Covers approximately 64 sq.ft.
• ✅ MADE IN THE U.S.A - This safe to use product is manufactured in the US and made to the strictest standards. Put our clear sealant food safe epoxy resin kit to the test today! Endorsed and trusted by many marine and veteran hobbyists.
• ✅ PROFESSIONAL ALL IN ONE KIT - Besides the resin and the hardener (1 gallon of each), when you buy this DIY and art resin kit you also get a mixing cup, silicone spatula, silicone spreader, and nitrile gloves. We stand behind a 100% satisfaction guarantee and a free return if you are unhappy with any of our products for any reason no questions asked.

Product features

PATENTED LOW VISCOSITY FORMULA

MAMAR Epoxy Resin Plus - New Patented Formula is made from premium commercial grade ingredients and is the lowest in viscosity on the market yet still strong and durable. It is the perfect texture and best choice for artwork, crafts, and DIY projects. Great for doming, coating, and embedding. The ultimate multi-purpose epoxy resin that is suitable for any application. This food safe epoxy is manufactured in the US and made to the strictest standards.

SELF-LEVELLING GLISTENING FINISH

Make Your Art Beautiful - Enjoy an intense glistening finish on wooden table tops, artworks, or any other surface in need of durability, extra strength, and water protection that will last for years to come. Pour our epoxy onto a flat table surface and watch it level it self like magic to get that perfect flush finish. Trusted by many professional artists for marine and dry projects.

ULTIMATE UV PROTECTION

Revolutionary Anti Yellowing Plastic Layer & UV Protection - Our new food grade epoxy is formulated and proven to resist yellowing and harmful UV rays over long periods of time so you can rest assured that your precious art is protected from the elements and you can display your work inside and out! It is designed to create a very thin top layer of plastic on the surface that protects the epoxy beneath.

100% CRYSTAL CLARITY

Crystal Clear With NO Bubbles - Our new exciting Epoxy Resin Plus formula went through rigorous weeks of testing in a lab to ensure it meets the high standards of our fellow artists. Rest assured that our special liquid is completely transparent and does not contain any bubbles! As always it is still great practice to torch the surface of your artwork after a pour.

There's no place for anything less than perfect when it comes to our customer's satisfaction.

Why Choose MAMAR Epoxy Resin Plus?

As one of the leading most trusted epoxy brands for serious artists, craftsmen, and DIY hobbyists, MAMAR Epoxy Resin Plus is certainly a must have. It adds a protective and intense glistening touch to your artwork, without compromising quality or protection unlike anything else out there. Free of toxins, odors, and VOCs ensure that you work with maximum comfort so you can focus on making what you love most. Crafted with commercial grade premium materials, with a self-leveling formula and perfect texture, this crystal clear epoxy art resin is suitable for artwork, tabletops, woodwork, jewelry, and much more! With our high-quality resin, make sure your artwork retains its gorgeous beauty over the years!

In addition to the resin and hardener, when you invest in our DIY and art resin epoxy kit you also get a mixing cup, silicone spatula, silicone spreader, and nitrile gloves.

EMBEDDING

Let Your Imagination Run Wild! - MAMAR Epoxy Resin Plus is perfect for enclosing your favorite art pieces in a solid hard shell that will protect them for years to come! You can also embed your regular everyday objects for fun and put them up for display! All you have to do is get a rubber mould of the desired shape, put your art in it and pour away! The perfect personalized gift.

DOMING

Protect & Make It Shine - Protect your artwork and tabletops or just give them an intense shine that will make any piece pop out and be beautiful. Make your precious art attractive while at the same time protecting it from scratches and water damage. Doming is an excellent way of preserving and enhancing the gorgeous colors of the piece.

PROFESSIONAL ALL IN ONE KIT

For Beginners or Pros - Whether you are a beginner or pro, when you invest in one of our epoxy plus kits, you will get everything you need to get started! This includes a premium set of a silicone spatula, silicone spreader, nitrile gloves, and a 500ml mixing cup. They can be washed and used again over and over for all your projects.

BARS & TABLETOPS

MAMAR Epoxy Resin Plus provides excellent protection for tabletops and bars, while giving them an intense shine that will last for years. Protect your valuable furniture from water damage and give them a look to impress!

SCULPTURES

Create cool sculptures that will wow anyone! MAMAR Epoxy Resin Plus is the perfect texture for sculpting and will become rock solid after 24 hours of curing. Put our two part epoxy resin for wood kit to the test today!

JEWELRY

Unleash your inner creativity and create something that screams your personality. MAMAR Epoxy Resin Plus is perfect for crafting cool and shiny jewelry pieces that can make great personal gifts but also something very unique that you or your loved ones can wear outside!

ARTWORK, CRAFTS, & DIY PROJECTS

Give your paintings or artworks and other crafts and DIY projects a breath of life by applying our protective resin plus coating on the surface! Enjoy a clean and shiny finish that will leave people simply in awe.

Product description

Jess Crow, owner of Crow Creek Designs in Palmer, Alaska, is an extraordinary builder, painter, woodworker, and teacher (and mom!), whose epoxy resin art and designs have inspired a legion of social media followers, with features on LinkedIn, Insider, and DIY Network. Her stunning epoxy art and hand-built furniture are inspired by the beauty of wood and the flow of nature, as evidenced by her innovative ocean designs and other artistic techniques. Jess is continuously pioneering new processes involving epoxy and functional art. Her exceptional work is a testament to the performance and ease of use of our TotalBoat epoxy line, and we are proud to partner with her to create TotalBoat MakerPoxy Clear Artist’s Resin by Jess Crow.MakerPoxy was formulated especially for DIY and pro artists, woodworkers, and makers because of its ease of use and gorgeous, high-gloss, self-leveling, scratch-resistant finish. It can be used in a wide variety of resin art applications, including resin paintings on canvas and wood, epoxy wall art, decorative areas on charcuterie boards, dining room furniture like river tables, headboards and bedside tables, coffee tables, and more, including casting and coating projects. It flows easily and can be tinted with a variety of alcohol inks, tints & pigments to give you an unlimited capacity for innovation and creativity. Whether you’re a professional artist, or you just want to to try your hand at channeling your own inner artist, find your flow with MakerPoxy and get beautiful, glass-like, professional results. You’ll be inspired to make something of it!Compare TotalBoat MakerPoxy Clear Artist’s Resin to MAS Art Pro Epoxy Resin, ArtResin, Alumilite, SuperClear, Faux Rizzle, WiseBond, Art 'N Glow, or Unicone epoxy. MakerPoxy by Jess Crow provides an ultra high-gloss finish, and excellent self-leveling properties. BPA-free formula means cured Makerpoxy is safer for food contact.

• PROFESSIONAL-GRADE CRYSTAL CLEAR EPOXY RESIN PREFERRED BY RESIN ARTISTS, WOODWORKERS, DIY MAKERS, CRAFTERS, AND HOBBYISTS. Mixed epoxy flows easily. Blend with color pigments & tints for unique works of resin art, furniture like river tables, headboards, coffee tables, wall art, and more
• GLASS-LIKE, SCRATCH-RESISTANT, UV-RESISTANT HIGH BUILD FINISH. Super glossy, self-leveling sooth finish resists scratches and yellowing. For outdoor use, you can overcoat MakerPoxy with clear varnish or urethane for maximum UV resistance. Durable cured resin strong enough for furniture and table tops
• LONG WORKING TIME ideal for large or complex resin art pours. Once resin and hardener are mixed, you have about 60 minutes at 77°F, when applied at the proper thickness (1/8”-1/4”). Extended working time is also great for first-time resin users, making it easy to take your time
• EASY TO MEASURE AND APPLY. Simple 1:1 mix ratio. Just mix equal parts of resin and hardener for beautiful, smooth, high-gloss results on wood, plastic, fiberglass & metal. Use with alcohol inks, liquid color pigments, mica powder pigments & acrylic paints. BPA-Free formula safer for food contact
• MADE IN THE USA. Choose from 4 kit sizes: 8 oz. Kit (4 oz. of Resin & 4 oz. of Hardener), 1 Pint Kit (8 oz. of Resin & 8 oz. of Hardener), 1 Quart Kit (1 Pint of Resin and 1 Pint of Hardener), and 1 Gallon Kit (½ Gallon of Resin and ½ Gallon of Hardener). BONUS: Quart and Gallon Kits include stir sticks, disposable beakers, and mixing cups. NOTE: 8 oz. & Pint Kits contain Resin and Hardener ONLY.

User questions & answers

Question:	Can you use this on decoupage projects and do you brush it on
Answer:	can gorilla glue be used to repair food dishes
Question:	Does it smell strong
Answer:	It would likely hold well, but dry to lumpy for comfort for insoles. I've used it to glue soles on slippers which works well, and holds for a long time.Used shoe glue in the past for outer soles, and found it worthless, which is why I tried Gorlla this time.
Question:	I need to pour a 3" disk that is 1" thick and need to drill and sand it when finished, is that possible with this product
Answer:	4 small tubes
Question:	How easy is it to remove bubbles from this resin? i just tried artresin and was not impressed with all the micro bubbles. is this resin better
Answer:	Hello, We would not recommend using Gorilla Super Glue to hand curtain rods. If we can be of further assistance, please contact our Consumer Affairs team at 800-966-3458 or through our website at www.gorillatough.com/contact and reference case #270307. Thank you, The Gorilla Glue Company

Product description

SC110 is an epoxy polymer coating for metal, concrete, wood, fiberglass and other surfaces requiring a clear coating. SC110 is a specially formulated 2- component epoxy with a modified cycloaliphatic amine curative. SC110 combines a UV absorber coupled with a hindered amine light stabilizer which inhibits degradation of the epoxy from sunlight. SC110 forms a highly durable wear resistant surface that is semi-flexible, impact resistant, and resistant to water, traffic, fuel, oil, and mild acids. SC110 exhibits excellent corrosion and chemical resistance and is designed for marine grade applications as well. SC110 is 2:1 Resin to Hardener Mix Ratio. This kit makes 1 full gallon when mixed.

• Clear Non-Yellowing and Non-Blushing Epoxy with a Cycloaliphatic Hardener
• Excellent Gloss and Clarity and Excellent Chemical Resistance
• 100% Solids... Does not contain Cheap Diluents or Solvents
• Clear Finish Holds up to Direct Sunlight Exposure
• UV Resistant... SC110 combines a UV absorber coupled with a hindered amine light stabilizer which inhibits degradation of the epoxy from sunlight.

User questions & answers

Question:	Can i paint over the epoxy? what kind of paint should i use or not use? can i apply the epoxy over paint
Answer:	There is plug in heater(stays on wall) sold by Amazon that has 2 setting1500 and 750 watts plus a remote control. I used it to heat an uninsultated 400 sq. ft+ 2 car garage in NC and it worked enough that the temperature never got below 50 degrees. Then best way to heat a garage is to insulate it including garage doors and use a 220 volt garage heater and you will be able to keep the garage at any you need no matter how cold it gets
Question:	Is this resin good for artworks, paper, woods, etc.? I need it for various art projects and "Decoupage" is one of them right now. Thanks
Answer:	Several heaters say they shouldn't be used in bathroom due to humidity ruining the coils. On the other hand, there's a picture at the page top for this product showing it sitting on the sink in the bathroom. So what is the answer? Get the heater is removed from the bathroom, except for when it's actually being used, maybe that's the solution?
Question:	How many square feet of fiberglass cloth can i 'paint' onto plywood with a three gallon kit
Answer:	YUP works good.
Question:	thickness will be 1/2 inch, outdoor, non yellowing / is this the product i'm looking for
Answer:	No it does not drie clear, It dries with a beige color. It also expands a good bit after application so use cautiously.

Product description

Miraclekoo UV Resin Hard UV Glue Ultraviolet Curing Solar Cure Resin Sunlight Activated Crafts For DIY Jewelry Making



Features:



Color: Transparent , Weight:25g / Bottle.



Cured with UV / sunlight, no mixing like AB resin.



UV Resin Cured hard within minutes, no more waiting , UV Lamp(36w): 2-4 minutes, Direct Sunlight (Sunny Day): 10-15 minutes



Please note:

1. In most cases, it will dry sticky if you don't use 36w UV light. But it can also cure totally if you put it in the strong sunlight for a long time.

2. It is not recommended to use this epoxy resin to make large objects.

• EASY TO USE & EFFICIENT:No mixing like AB resin which needs to mix and take long curing time , our art resin require no preparation and ready to use.Instantly cured in minutes with UV / sunlight.UV Lamp(36w): 2-4 minutes, Direct Sunlight (Sunny Day): 10-15 minutes.
• PREMIUM - Crystal Clear UV epoxy resin with self-leveling and self-degassing properties can cure smooth crystal clear, glassy finish. provides excellent scratch resistant, stain resistance and yellowing resistance.
• SAFE - Our hard type uv resin is made of high-quality and non-toxic materials.There is an odor before curing, it is harmless and will completely disappear after curing.
• WIDELY USE - Excellent for jewelry making, open back bezels, bezel setting, small silicone molds,crafts decorations, casting and coating, cast figurines and make resin paintings,garment accessories, encapsulate objects, make resin paintings etc.
• ECONOMICAL - Package includes 1000g (35oz) transparent uv resin which perfect for DIY craft making!Comes with small tip, simply open and squeeze.

Product description

Clear Epoxy Resin Art Resin Epoxy 16 Ounce Kit

• Premium epoxy kit - Aquaseal epoxy resin and hardener kit delivers extra durable results ideal for boat building, composite construction, house repairs, table top epoxy resin projects and more!
• All you need included - Aquaseal marine epoxy resin kit includes : resin 8 ounce bottle, hardener 8 ounce bottle, 2x measuring cups, 1x plastic spreader and 5x mixing sticks. Everything you need to start your clear epoxy projects.
• Easy to use - Mix 1 part epoxy resin and 1 part hardener for 20 minutes of work time on your marine epoxy projects. Use on wood, fiberglass, reinforcement fabrics, etched aluminum, bare steel, and lead.
• Faster curing and harder - Strong, clear epoxy resin, fully UV-resistant cures faster and harder, ideal durability for boat repair, table top epoxy and countertop epoxy projects.
• Customer service - Please read the instructions provided with the Aquaseal marine epoxy before use. If you have any questions or issues, please don’t hesitate to send the seller a message through Amazon and we will respond within 24 hours.

User questions & answers

Question:	Does it hold up well against the elements? Thank you
Answer:	Extremely quiet and as a plus, it really is a great heater. I was pleasantly surprised due to both things, volume of heat and quiet running.

• SPECIALLY FORMULATED FOR ARTISTS: MAS Art Pro was specially formulated for resin art users. Our art resin performs and finishes beautifully for a wide variety of resin art applications. 
• UV INHIBITED | LONGER WORKING TIME | HIGH BUILD FINISH: Resin artists will appreciate Art Pro has been formulated with UV inhibitors to slow down yellowing that can occur with all epoxy. Further, the longer working time and high build finish make our epoxy resin a great choice for resin art.
• PROFESSIONAL GRADE: Our epoxies are trusted by professionals and hobbyists alike. We pride ourselves on creating epoxy resins that are strong, dependable, and easy to use. TableTop Pro is ultra-clear, self-leveling, and a beautiful high-gloss epoxy resin coating. You'll appreciate the quality and consistency of our product.  
• EASY TO APPLY: Application instructions will accompany your purchase to help make your project a success. You can also watch our instructional video which will walk you through how to use MAS Art Pro epoxy resin.
• QUALITY YOU CAN TRUST: For over 25 years, MAS Epoxies has taken pride in manufacturing the highest-quality epoxy products available. We proudly manufacture our epoxy resin from start-to-finish in the USA.

User questions & answers

Question:	What is the amount of linear footage of coverage per gallon
Answer:	If your measurements are exact for what you are needing, then no I don't think this would fit. This vent measures approximately 3 6/8". None of the vent holes in my house are cut perfectly, in fact I had to do some filing and rasping due to a previous homeowner's ham-handed carpentry. But I did get them to work because they were essentially standard to my house anyway. This vent is 4 inches wide and 10inches long measuring on top. Its approx. 3inches and 6/8ths wide underneath.
Question:	can this be used for pen blank molds and then be turned on a lathe
Answer:	The top piece is a very flimsy metal. Was easily bent by hand. And the bottom piece is plastic. I received them July 13th I believe and three were broken within the first week.
Question:	mas table top resin is nice and thick and also very forgiving when it comes to residual silicone left on acrylic pours. how does the art epx compare
Answer:	Good afternoon, I do not have any of these in stock that are brown 4x10. Sorry!
Question:	Is this a 1 to 1 mixing ratio
Answer:	I would set it at 60, no need heating more than you need. The problem with this unit is if you have any kind of power outage the heater turns back on at 90 degrees instead of what you had it set at.