13 best carbon monoxide detectors

Product description

Kidde 21025778 Carbon Monoxide Alarm Battery. Made from quality materials for durability and performance. Designed for quick and simple installation.

• 2 AA battery backup
• Low battery hushes
• Event memory
• Loud 85 decibel alarm
• Low battery signal

User questions & answers

Question:	Would this device work in a 6' x 6' hunting blind with a Mr. Heater heating unit
Answer:	Not for sure but wife read that rhey can fluxiate between 0-3 with no problems mine does it also
Question:	your cob b lcm coc allarm is 15$ 6 is 99$ . why does quantity coct more
Answer:	When I used the digital gas detector to test it worked fine.
Question:	How far apart are the mounting holes
Answer:	There are two possible causes. The unit was not zeroed out upon activation or you do have a very low level of gas in your home atmosphere, with the first being my best guess. Unplug and move and re-check the reading. If this does not resolve the issue send it back for a new one. Mine has worked well for 6 months so far.
Question:	Why is the 2 pack more than 2 times the price of the single detector
Answer:	I returned these detectors. They don't have any information printed on the case - no manufacturer name, no instructions, no UL approved indicator, etc. These were made in China which is usually okay but I am not comfortable in relying on them to protect my family. I will be researching further and looking for better detectors that can be trusted.

Product features

Battery Operated Carbon Monoxide Alarm

The Kidde KN-COB-B-LPM Battery-Operated Carbon Monoxide Alarm is intended for continuous monitoring of carbon monoxide levels. The alarm features a piezoelectric horn that is rated at 85 dB at 10 ft. The alarm is battery operated for uninterrupted monitoring, even during power outages, and runs on 2 AA batteries, which are included.

Battery-operated carbon monoxide detector; no hardwiring required

Alarm will sound when dangerous levels of CO are detected

Test/reset button tests the unit for proper operation and resets the alarm

Product description

1111111111.

From the Manufacturer

Carbon Monoxide Alarm AC Powered with Battery Back up; Tamper resistant feature; Led operation; Test reset button; Alerts user to replace after 10 years of operation; Low battery hush; Event memory; UL listed.

• Tamper resist feature – Can be activated to cause unit to go into alarm if it has been unplugged or has come loose from the outlet
• 2 LED’s: Red - Illuminates when in alarm mode. Green – AC power is present, normal operation
• Test/reset button: Tests CO alarm circuit operation and allows you to immediately silence the alarm
• End of life alarm: Alerts user to replace CO alarm after 10-years of operation
• Provides peace of mind against the silent killer; Temperature range: 40˚F (4.4˚C) to 100˚F (37.8˚C)

User questions & answers

Question:	When I unplug this device the green light goes off even though the batteries are installed as a backup. Is that normal
Answer:	It's about 5 1/2 in from hinge to hinge ~ 14.5 cm. It does provide full cover. The foam is flush with my face without being uncomfortable. It however is not waterproof. The foam has air slots so it can breathe. I've used these for Chemistry lab as well as wood working, and they work great.
Question:	When I try put battery in or plug it in, the alarm goes off! Does that alarm sound stop? It's brand new
Answer:	They stay on surprisingly well! I use them for my dog grooming business. They are light weight so that works good for me. They might be a bit too light for sports. If you got hit with a ball they would probably crack and potentially cut you.
Question:	How do you turn on the "low battery hush
Answer:	Yes, it should do a good job to keep out drywall dust. However, I ended up removing it due to condensation buildup while using it
Question:	What is the location of the wall plug on the device? Will it cover the entire outlet
Answer:	yes they can fit over Rx glasses but I don't recommend because they became blurring and you will not see very well

Product features

Quality Protection

The Kidde KN-COB-DP2 plug-in carbon monoxide alarm with battery backup provides you and your family with a warning signal to protect against dangerous levels of carbon monoxide in your home. The battery backup feature provides continuous monitoring of CO levels, even during power outages when AC-only units are not providing protection. The KN-COB-DP2 alarm has a 10-year product life, providing 40% longer protection than other CO alarms.

Protection You Can Trust

Nothing is more important than making sure your family is safe and prepared for anything, and with this plug-in carbon monoxide detector from Kidde, you will always be afforded peace of mind! This CO alarm includes a battery backup to make sure it is monitoring your home at all times and uses high-tech electrochemical sensors to provide accurate carbon monoxide readings that will always keep you protected.

Plug-in to Peace of Mind

To prevent nuisance alarms from everyday activities, CO detectors are time-weighted alarms that are based on time and the concentration of CO levels. This unit will only sound an alarm if low levels of CO have been detected over a long period of time, but high or unhealthy levels of CO will immediately trigger an alarm.

• ACCURATE & RESPONSIVE: Built with an advanced electrochemical sensor and intelligent chipset, the CD07 CO detector quickly and accurately detects dangerous carbon monoxide (CO) leaks in the surrounding air; designed to give you the earliest possible warning of CO threat with a loud 85 dB alarm and a rapid flashing LED indicator
• 10-YEAR BATTERY & PREMIUM MATERIAL: Comes with a 10-year sealed lithium battery for uninterrupted operation; housed in a frame made from premium PC plastic material that is both fire-retardant and highly durable; provides the ultimate protection for you and your family’s safety
• LARGE LCD DISPLAY: Clearly displays the real-time CO levels in PPM (parts per million) taken from the surrounding air, with an updated measurement taken every 10 seconds; comes equipped with a peak level memory, showing you the highest CO concentration measured since the last reset
• EASY INSTALLATION: Attach the mounting bracket onto the surface of a wall or ceiling with the provided screws and mount the alarm into the bracket by pushing them together and twisting the unit clockwise, automatically activating the unit
• WORRY-FREE AFTER-SALES SERVICE: We provide a 60-day money-back guarantee and 5-year warranty for all X-Sense carbon monoxide detectors and smoke alarms; if you have any questions, please feel free to contact us, and we will get back to you within 24 hours

User questions & answers

Question:	Does this device work with Nest products and where ids it made
Answer:	This unit does not depend on the internet to work. It is portable. However, it has internet connection ports so it can use every feature the net can offer. I am very pleased with it's operation and quality.
Question:	Can this be mounted vertically on a wall
Answer:	It has been two weeks since I bought this snake endoscope camera. I used it to repair my drain pipe. When I got this inspection camera, there was still electricity in it. After a full recharged, I used it several times. It still has power. I think it can be used for at least 4 hours after fully charged. This is a good device with a large capacity battery.
Question:	Can this be synced with the wireless smoke alarms also
Answer:	Hello, this is how I did it. Insert the USB data cable in the shutdown state, and then turn it on again, the data of the TF card can be directly read by the computer. When the memory card is full, I will transfer the important files inside to the computer, and then format the TF card, then you can start using it again, hope it will help you.
Question:	Are batteries included with the product
Answer:	I use it to check my household appliances. I also encountered the problem of blurred video before. Before using it, check whether the lens is blocked by dirt and wipe it clean with a lens cloth. And because the focus of the inspection camera is 3-10cm/1.2-3.9inch, the observation distance needs to be within this range to get the best quality pictures and videos. When I do these two points, It works well.

Product features

TEST/SILENCE Button

The TEST/SILENCE button allows you to test the alarm to ensure it is functioning properly. When false alarms occur, the unit can be silenced with a simple push. Make sure to test your alarm every week.

85 dB Loud Alarm

This alarm is designed to give you the earliest possible warning of CO threat with both a loud 85 dB alarm and a rapid flashing red LED indicator. This will wake up you and your family, even when sound asleep, giving you more response time to escape or create an escape plan.

Self-Check Function

This CD07 10-Year battery carbon monoxide detector will automatically check its battery and sensor every 10 seconds to ensure that the key sensor and critical circuit are working properly.

Low Battery Warning

When the battery power is low, an LED light will flash yellow with 1 beep every 60 seconds. In this case, please deactivate the CO alarm and replace it with a new one.

Product description

The BRK SC9120B hardwire combination smoke and carbon monoxide alarm detects two hazards with one simple unit. Carbon monoxide (CO) is a colorless, odorless, deadly gas. It can be emitted by sources including gas or oil furnaces, gas clothes dryers, water heaters, fireplaces, wood stoves, charcoal grills, gas ranges, and space heaters. A clogged chimney, improper venting, and attached garages can also cause carbon monoxide accumulation. The BRK SC9120 hardwire combination smoke and CO alarm with battery backup includes these features: Quick plug in power connector for easy installation, 120 volt AC inter connectable (with maximum 18 compatible devices 12 other compatible smoke alarms + 6 compatible devices like bells, horns, repeaters and door closers. If one unit triggers an alarm, all smoke alarms in the series will sound. Single test/silence button which both silences a non-threatening alarm or low battery warning and allows you to test the unit's functionality. Automatically performs internal test of functionality. Latching alarm indicator which automatically identifies which unit initiated the alarm. Battery drawer lock and mounting bracket lock for tamper resistance. AC power indicator and alarm indicator light. Low battery warning "chirp" and missing battery tab. 9 volt battery backup for peace of mind during power outages. All BRK Electronics carbon monoxide alarms are listed to UL Safety Standard 2034 for residential carbon monoxide alarms. Includes 9 volt backup battery. 7 year limited warranty. Includes: One combination smoke and CO alarm, one 9 volt battery, and user’s manual.

• Keep your family safe with this hardwired smoke and carbon monoxide alarm; The battery backup means constant monitoring, even if there's a power failure
• Features an electrochemical carbon monoxide sensing technology as well as an ionization sensor for smoke detection.
• Indicator lights on the face of the unit display the presence of smoke or carbon monoxide, while an 85 decibel siren provides a clear, loud warning upon detection
• Can connect to other compatible BRK or First Alert detectors, to ensure all alarms will sound when threat is detected
• Simple to use, with a single test/silence button, and side load battery compartment; Tamper resistant locking brackets and universal mounting brackets make installation easy
• Rigorously tested to meet UL standards
• Faster turnarounds on job sites with the easy-to-install, most-trusted alarms in home safety
• First Alert has been the most trusted brand in home safety since launching the first residential smoke alarm in 1958 (Based on a First Alert Brand Trust Survey in February 2018)

User questions & answers

Question:	What is the manufacture date on these items
Answer:	Hello. Yes, but not the way you mean. When the alarms go off, there is always one alarm going off and setting off all of the others. This alarm will have a green light flashing every second as well as the red light. You have to identify that alarm and either put it in HUSH mode or unplug it and take it down to stop the others. This is intentional so that if you are not leaving the house then you are identifying and investigating where the smoke situation is and if there is danger. The HUSH mode will make the alarm require more smoke to go off and for a small amount of smoke will stop it for about 8 minutes If there is too much smoke, the HUSH mode will not stop the alarm for going off.
Question:	If the alarm goes off, how can you tell whether it's due to CO or fire if there is no voice alert
Answer:	Hello. Yes, this alarm comes with a wiring harness connector.
Question:	Because its a combo alarm where is the best place to install it since smoke rises and carbon monoxide doesn't
Answer:	Hello. The answer is no, the battery is only a temporary back up. If you want an alarm that is battery only, you will want our KN-COPE-D.
Question:	Why does this model contain the radioactive part? I am sure you are going to tell me that it is a trace amount and that it has all approvals
Answer:	Hello. When plugged in AC power, it is supposed to have a solid green LED light. When running on battery alone, it should have a green light that flickers every 60 seconds. If this is not what is happening, call us when you are on location with a ladder at 1-800-880-6788 so we can figure out what is going on and how we can resolve this.
Question:	When these are interconnected with other units, can hushing one of them hush all of them? Some of mine are in places that are hard to get to
Answer:	I paid FOR for 6 and only got 4. It’s listed as 6. I had to buy two more from Home Depot. DO NOT BUY THIS ITEM.
Question:	does it come with the hardwire connector
Answer:	Does not connect to hard wire. Only battery
Question:	Do you have to hardwire it in? Can it run on just the battery
Answer:	I just checked 2 of them, and am unable to locate that information.
Question:	How do you tell if it is working properly. Is it supposed to have a constant light
Answer:	The back cover comes off install battery and replace

Product features

Always Alert

In order to monitor your home even if you are away, this detector includes an Alarm Memory feature. If the green LED is blinking once every 16 seconds, the unit has detected CO levels of 100PPM or higher, or detected smoke and then ceased its alarm. Pressing the Test/Reset will reset the memory and inform you of the hazard detected.

Easy to Install

Ensure the safety of your family and home with the combination smoke and carbon monoxide alarm from Kidde. This is a hardwired alarm that can be used in an interconnected system, and it features a battery backup, in addition to voice alerts. Using an advanced photoelectric sensor, capable of detecting visible fire particles associated with smoldering fires, and an electrochemical sensor for CO detection, you can rest easy and feel protected.

Easy Access

If the low battery warning sounds, there is a convenient front-loading battery door so that you don’t have to remove the alarm from its mounting bracket to replace the alarm. Additionally, to ensure that there is always a properly functioning battery, the battery compartment will not close if the battery is not installed correctly.

Product description

Plug-In carbon monoxide alarm with battery backup.

Protect your family from the dangers of carbon monoxide (CO) exposure with the Kidde KN-COPP-3 Nighthawk Plug-In Carbon Monoxide Alarm with Battery Backup and Digital Display. The Nighthawk is an easy-to-install unit that provides reliable protection against the dangers of CO. It features a digital display that shows CO levels in parts per million allowing you to see if, how, and when levels change.

Plug-in unit with battery backup and digital display that shows CO level Level button displays the peak CO level recorded by the alarm since it was last reset Loud alarm pattern sounds when unit detects elevated CO levels Direct-plug, 6-foot power cord, and table top mounting options. Five-year limited warranty

This discreet alarm is designed to fit into any standard A/C outlet in your house. View larger.

The easy-read digital display updates every 15 seconds to indicate any abrupt changes or alarming trends in CO levels. View larger.

Advanced Technology in an Easy-to-Install, Plug-In Design

Designed for home use, the Kidde KN-COPP-3 Nighthawk is a UL-listed, A/C-powered, plug-in CO alarm that utilizes sophisticated electronic components and sensor technology to protect you and your family from the dangers of CO. It plugs directly into a standard A/C outlet and includes a 9-volt battery backup that provides continuous monitoring of CO levels--even during power outages.

About Carbon Monoxide: The Silent Killer

The leading cause of accidental poisoning deaths in North America, carbon monoxide (CO) is often referred to as the silent killer because it's odorless, tasteless, and invisible. Carbon monoxide poisoning can come about via a number of sources, including everyday items and appliances in your home or office. And because symptoms of CO poisoning mimic the flu or other common illnesses it can often go undiagnosed.

Audible Alarm Pattern Alerts you to Elevated CO Levels

When placed on every level of your home, alarms like the KN-COPP-3 Nighthawk can help protect everyone in the house from CO exposure by giving you an unmistakable signal when levels have reached an unhealthy point. If unhealthy levels are detected, the alarm will emit four quick audible beats every five seconds until either levels decrease or the reset button is pressed.

Easy-to-Read Digital Display Shows CO Levels

The KN-COPP-3 Nighthawk is unique among traditional CO alarms because of its digital display. This display clearly shows levels of CO that the unit has detected and stored-- from 30 to 999 ppm--and it updates every 15 seconds to indicate any abrupt changes or alarming trends. The display also shows the peak CO level recorded by the alarm since it was last reset or unplugged.

LED Shows Sensor Status

With the KN-COPP-3 Nighthawk, you never have to wonder if the sensor is functioning properly. A blinking dot in the lower right-hand corner of the display denotes normal operation, so you can trust that it's working. In addition, you can test alarm function by pressing the test/reset button at any time to verify that the horn and electric circuitry are operating properly.

Convenient Mounting Options

The KN-COPP-3 Nighthawk has a low-profile design that makes it suitable for any room in your home. The detector can be plugged into any standard A/C outlet; it's plug can be snapped into the back of the unit and can be rotated so the alarm remains vertical, independent of whether the electrical socket is mounted vertically or horizontally. In addition, the alarm comes with a 6-foot extension cord, so the unit can be plugged into the wall outlet and then placed on a table or shelf. For the most thorough protection, place an alarm on every level of your home.

The UL-listed Kidde KN-COPP-3 Nighthawk has a seven-year life and is backed by a five-year limited warranty.

About Kidde: A UTC Fire and Security Brand

Renowned for global leadership in fire detection and suppression, Kidde provides solutions ranging from portable fire extinguishers to advanced industrial controls such as flame detection and explosion suppression systems. Kidde is a UTC Fire and Security brand, with a history that's rich with innovations, from the patent of the Chubb Detector Lock in 1818 to the development of the world's first wireless networked smoke detectors in 2004.

What's in the Box

Kidde KN-COPP-3 Nighthawk CO Alarm, 9-volt battery, mounting hardware, and installation guide.

Keep your family safe by placing alarms and extinguishers in each area of the house, and by having a fire escape plan. Click here for a detailed image.

From the Manufacturer

The leading cause of accidental poisoning deaths in North America, Carbon Monoxide is odorless, tasteless and invisible, it's a silent killer. Kidde CO alarms include the most accurate sensing technology available, the patented Nighthawk electrochemical sensor. This alarm can be mounted three ways: plug directly into AC receptacle, mount on tabletop using 8 foot power cord, or wall-mount. The digital readout continuously displays carbon monoxide levels from 30-999 parts per million. This unit has a loud, 85-decibel alarm that sounds when CO reaches dangerous levels. One of the features of this product is peak level memory, which means this unit will recall highest level of CO present since previous reset. Install at least one CO alarm on every floor and in sleeping areas. Make sure CO alarms are at least 15 feet away from cooking or heating appliances to prevent false alarms. Replace CO alarms every 5 to 7 years to benefit from the latest technology upgrades.

• Peak level button – Displays the peak CO level recorded by the alarm since it was last reset or unplugged
• Test button functions – Tests the unit for proper operation and resets the carbon monoxide alarm
• LED operation – Blinking dot in lower right corner of display denotes normal operation
• Ten years after the initial power up, this alarm will “beep” two times every 30 seconds to indicate that it is time to replace the alarm.
• Note: This CO alarm is not battery operated. However, these alarms are equipped with 9 volt battery backup – the 9 volt battery is to supply short term back-up during a power outage.
• Power source: 120VAC. Temperature range-40˚F (4.4˚C) to 100˚F (37.8˚C). Humidity range-5%-95% relative humidity (RH)

Product features

Easy to Read Display

This plug-in CO alarm is designed with a clear, visible readout that will accurately record the levels of carbon monoxide present so that you can quickly know if an area of your home is at risk. It measures CO levels between 30 and 999PPM, and the display will also indicate if the battery needs to be replaced.

Unbeatable Protection

Always protect your family and home by making sure you are prepared for any emergency or hazard with the Kidde plug-in carbon monoxide detector. This CO meter uses an electrochemical sensor and features a clear digital display screen to monitor and record any CO levels in any room of your house. This sensitive and clear detector will leave you confident that you are protected against carbon monoxide.

Peak Level Memory Feature

Displays the peak CO level recorded by the alarm since it was last reset or unplugged

Product description

The First Alert CO615 dual power carbon monoxide plug in alarm alerts you to dangerous carbon monoxide. This carbon monoxide detector operates on a dual power system with battery backup for continuous monitoring, even in the event of a power outage. The backlit digital screen tells you at a glance what the carbon monoxide and power Levels Are. The Co monitor also features a convenient test and silence button and an end of life timer that lets you know when it is time to replace the unit.*ensure the outlet has power.*the battery is for back up only and is not intended to power the alarm for an Extended period of time in the absence of AC. *the alarm will light up the display briefly to indicate the unit is receiving power. *press and hold test button to ensure activation.

Carbon monoxide (CO) is the leading cause of accidental poisoning deaths in America, yet many people don't know they are suffering from CO poisoning until its too late. Since symptoms of CO poisoning are like the flu, you might not even know you're in danger at first. That's why a carbon monoxide alarm is an excellent way to protect your family. It can detect the CO you can't see, smell or taste in the air.

The First Alert CO615 carbon monoxide alarm uses an electrochemical carbon monoxide sensor-the most accurate technology available. Installation is as simple as plugging it in to any wall outlet. Its easy-to-read backlit digital LED display gives you a clear read-out of current CO concentrations in parts per million. The alarm includes a battery back-up giving you peace of mind in a power outage. The test/silence button both silences a non-threatening alarm or low battery warning and allows you to test the unit's functionality. The unit monitors and re-alarms if carbon monoxide levels persist sounding a loud 85-decibel horn. An audible and visual low battery signal alerts you to replace the battery and an indicator alerts you when a battery has been removed. An end-of-life alarm of three chirps alerts you to replace the unit. Two AA batteries are included. 7-year limited warranty. UL listed. --Bree Norlander

What's in the Box

One carbon monoxide alarm, two AA batteries, and user's manual

• Keep your family safe with this digital display, plug in carbon monoxide alarm; It works with any standard outlet and also has a battery backup for continuous monitoring of Carbon Monoxide levels, even if there's a power failure
• Features an advanced electrochemical carbon monoxide sensor; Peak level feature displays the highest concentration of carbon monoxide measured
• A loud 85 decibel alarm sounds when Carbon Monoxide levels reach dangerous levels
• To ensure complete protection make sure to place one on each level of your home and in each bedroom
• 7 year limited warranty; Equipped with end of life signal chirp, so you know when it’s time to replace the unit for safety
• All first alert CO alarms are rigorously tested to meet UL standards
• First Alert has been the most trusted brand in home safety since launching the first residential smoke alarm in 1958 (Based on a First Alert Brand Trust Survey in February 2018)

User questions & answers

Question:	What size home would this cover? Do I need more than one in a 1400 sq. ft. space
Answer:	Straight into the wall... two prongs on the back. The rear picture shown on Amazon shows the prongs, but it's a little confusing because the battery door is shown open - when the door is shut, it's out of the way so the unit can mount directly on an an electoral socket.
Question:	Does this alarm work when using an extension cord or must it be plugged directly into a wall outlet
Answer:	The manual for the CO605 plug-in with battery backup says that if the battery is low or missing, it chirps once a minute. I don't have the item myself, so if somebody can confirm that it does chirp if it is plugged in without a battery, I would appreciate it. As to another answer here, if you are hearing 3 chirps per minute, it means the alarm is not functioning properly; it is not because of a low or missing battery, which is supposed to give off only one chirp per minute.
Question:	can it detect levels of 20,30 or 40 ppm of CO? I know alot can only detect 70 ppm of CO or above...but I'm concerned of a small CO leak of below
Answer:	If it is a 9 volt battery, it may not be seated correctly. See the video on the first alert website, and be prepared to do some hard pushing to get the 9V battery to engage. I had 3 9V units, and 2 of the 3 seemingly required excessive pressure to get the batteries to engage. When I first thought I had the batteries installed by just closing the door, the unit chirped until I got the batteries shoved on hard.
Question:	If I plug this directly into the wall does it over both outlets? I have a nightlight in my hall where I want to place this unit
Answer:	CO is slightly lighter than air, but about the same weight as Nitrogen molecules that is 78% of air. It mixes evenly over time. Researchers tested this by injecting CO into a column of air at different heights. All trials mixed evenly but the injection at the top took a little longer to reach equilibrium. Therefore, it's more important to put the detector near where the likely source might be or near where people might be sleeping than a particular height. https://www.ncbi.nlm.nih.gov/m/pubmed/21536403/

Product description

This handy 2-pack of First Alert CO400 Carbon Monoxide Alarms utilizes electrochemical carbon monoxide sensors to monitor your space for carbon monoxide threats. The battery-powered design doesn't require an electrician; simply insert the included 9-volt battery into each alarm, and the carbon monoxide detectors are ready to go. The advanced electrochemical CO sensors detect carbon monoxide leaks from multiple sources, such as faulty fuel-burning appliances, blocked chimneys, and generators running inside or too close to homes. When CO levels become elevated, a loud 85-decibel alarm alerts you to the threat. Because CO evenly distributes itself, it's important to have a CO detector on every level and in every bedroom of your home. Designed to be simple to use, each CO detector has just one button that silences or tests the unit, as well as an end-of-life timer that lets you know when it's time to replace the device.

From the Manufacturer

Carbon monoxide (CO) is the leading cause of accidental poisoning deaths in America, yet many people don't know they are suffering from CO poisoning until its too late. Since symptoms of CO poisoning are like the flu, you might not even know you're in danger at first. That's why a carbon monoxide alarm is an excellent way to protect your family. It can detect the CO you can't see, smell or taste in the air. The First Alert CO400CN2 2-Pack carbon monoxide alarm uses an electrochemical carbon monoxide sensor-the most accurate technology available. The permanent sensor lasts up to five-Years. Battery access in back of unit, 9 Volt battery included. The test/silence button both silences the alarm and allows you to test its functionality. The unit monitors and re-alarms if carbon monoxide levels persist sounding a loud 85-Decibel horn. No installation is required and the attractive design allows the unit to be placed anywhere you need it. It includes an optional wall mount with no outlet required. An audible and visual low battery signal alerts you to replace the battery. Pull down action chart has convenient guide on what to do if an alarm sounds. 5-Year limited warranty. UL listed.

• Keep your family safe with this 2-Pack of easy to use, battery operated carbon monoxide alarms; Battery powered alarms provide continuous monitoring of CO levels, even if there's a power failure
• Features an advanced electrochemical carbon monoxide sensor that accurately detects carbon monoxide levels, no matter where the detector is placed in the room
• A loud 85-decibel alarm sounds when CO levels reach dangerous levels
• To ensure complete protection make sure to place one on each level of your home and in each bedroom
• 5-year limited warranty; Equipped with end-of-life signal chirp, so you know when it’s time to replace the unit for safety
• All first alert CO alarms are rigorously tested to meet UL standards

User questions & answers

Question:	What is date of manufacture
Answer:	If your home has a good central location, where air will circulate from most areas of the house, I would say that one carbon monoxide monitor should be sufficient. In the case of a multi-story dwelling, I would invest in one carbon monoxide monitor per floor. Our home is a good example of a single floor dwelling of approximately 1400 sq. feet, with excellent air circulation. We have one monitor in a well ventilated hallway that is common to all the rooms of the house. I hope this response is helpful in your decision making.
Question:	Does this come with the screws for installation or do I need to purchase separately
Answer:	The instruction booklet that came with my First Alert carbon monoxide alarm (I do not know if I bought a "model C0615" -- my alarm has NO identifying alpha-numeric) informs me that there IS an extension cord already on the back of the alarm; it also tells how to access it. I unplugged my alarm from the outlet, turned it back-side-up and true enough the 2 pronged plug you use to plug it into the electrical outlet is part attached to a lightweight extension cord that I would estimate to be about 4 or 5 feet long. The instruction booklet says that is for use by those who want to remain standing and look at the alarm "face-to-face." Hope this helps, Fat.
Question:	why does 9 volt battery not fit in compartment- door won't close
Answer:	This unit probably detects CO at less than 30 ppm, but is not allowed to display that level unless a button is pushed. In this case, the peak level the alarm detected since last reset is what will show, not the current ambient level. From 30 to 70 ppm, the display can show the ambient level, but the alarm will not sound until it's been in that range for 30 days, as mentioned. At 70 ppm, the alarm is not to sound for at least an hour, and no more than 4 hours. That's UL requirements, which most codes across the US adhere to.
Question:	What is best location for CO2 detector
Answer:	No it will fit in the bottom leaving the top for your night light

Product description

The First Alert SCO5CN Combination Smoke and Carbon Monoxide Alarm features dual sensors to detect both smoke and carbon monoxide in a single device. A photoelectric sensor detects the smoke most often produced by smoldering fires, and minimizes false alarms from cooking smoke or shower steam. Additionally, the advanced electrochemical CO sensor detects carbon monoxide leaks from multiple sources, such as faulty fuel burning appliances, blocked chimneys, and generators running inside or too close to homes. A loud, 85 decibel siren alerts you to the threat; unique alarm sounds and indicator lights on its face distinguish a smoke warning from a carbon monoxide warning. This carbon monoxide and smoke detector is battery operated, so you don't need an electrician for installation. Requiring just two AA batteries and featuring an easy access battery compartment for quick changes, this smoke and carbon monoxide detector has a single button that allows you to silence a false alarm or test the unit.

Carbon monoxide (CO) is the leading cause of accidental poisoning deaths in America, yet many people don't know they are suffering from CO poisoning until its too late. Since symptoms of CO poisoning are like the flu, you might not even know you're in danger at first. That's why a carbon monoxide alarm is an excellent way to protect your family. It can detect the CO you can't see, smell or taste in the air.

The First Alert SCO5CN carbon monoxide and smoke alarm uses an electrochemical carbon monoxide sensor-the most accurate technology available. The alarm uses photoelectric smoke sensing technology which is environmentally friendlier and which reduces nuisance alarms, making it ideal for cooking areas. It is also great for sensing slow smoldering fires quickly. The permanent sensors last the lifetime of the alarm. The test/silence button both silences a non-threatening alarm or low battery warning and allows you to test the unit's functionality. A low battery signal alerts you to replace the battery and end-of-life alarm of three chirps alerts you to replace the unit. Two AA batteries are included. 5-year limited warranty. UL listed. Not available for sale in Massachusetts.--Bree Norlander

What's in the Box

One combination carbon monoxide and smoke alarm, two AA batteries, and user's manual. This does not contain voice feature.

• Keep your family safe with this battery operated smoke and carbon monoxide alarm; Battery powered alarms provide continuous monitoring of CO levels, even if there's a power failure
• Features an electrochemical carbon monoxide sensing technology as well as a photoelectric sensor that detects the larger particles of a smoldering fire
• Indicator lights on the face of the unit display the presence of smoke or carbon monoxide, while an 85 decibel siren provides a clear, loud warning upon detection
• Battery operated unit installs quickly and easily without an electrician. Low battery signal mute, quiets low battery signal for up to 8 hours
• Simple to use, with a single test/silence button; EZ access battery drawer allows you to change battery without removing alarm from ceiling
• 7 year limited warranty; Equipped with end of life signal chirp, so you know when it’s time to replace the unit for safety; All first alert alarms are rigorously tested to meet UL standards
• It can ship within the US except New York
• First Alert has been the most trusted brand in home safety since launching the first residential smoke alarm in 1958 (Based on a First Alert Brand Trust Survey in February 2018)

User questions & answers

Question:	pack is $30, 2 pack is $90. Why is a two pack so much? I thought the idea was to incentivize more product at a lower cost. This is halarious
Answer:	I no longer live in the apartment where I replaced the old smoke alarm, but you will love this one. It's so nice to flip the battery holder down and not have to remove the battery from the unit.
Question:	Advice on false alarms? Goes off every week or so. It's in our kitchen/living room, but goes off even when we are not cooking. Goes 1 min then stops
Answer:	No
Question:	I have these througout my house and rental unit. Installed them about 7 years ago and many malfunctioning. Any durability mprovments since 7 yrs ago
Answer:	The instructions that come with the unit duplicate what I have read from several Fire Department sources: you can place your unit on the ceiling, but AT LEAST 4 inches (10cm) from the wall. If you want to mount it on the wall, mount it MORE THAN 4 inches (10cm) BELOW the ceiling, but NO LOWER than12 inches (30cm) below the ceiling. It has to be high enough up the wall to "smell" the smoke, but that 4 x 4 inch (10cm x 10cm) area where the wall meets the ceiling can sometimes harbor a "dead zone" of still air where the smoke would NOT reach the detector quickly enough during a fire to warn you in time. Thus, do NOT mount your detectors too close to where the wall meets the ceiling.
Question:	How long do batteries last
Answer:	Ionization type. I actually looked at at manual to be certain.

Product description

The First Alert CO605 Plug-In Carbon Monoxide Alarm with Battery Backup utilizes an electrochemical carbon monoxide sensor to accurately and effectively warn you of elevated CO levels. The plug-in design and included battery backup mean your space can be continuously monitored for dangerous carbon monoxide gas, even during power outages. Simply plug the alarm into a 120-volt outlet, and the personal carbon monoxide detector is ready to go. When CO levels rise above a safe threshold, a loud 85-decibel alarm alerts you to the threat. Designed for simple use, the CO detector has just 1 button that silences or tests the unit, as well as an end-of-life timer that lets you know when it is time to replace the device.

• Keep your family safe from carbon monoxide in multiple rooms with this convenient plug in carbon monoxide alarm 3 pack; the alarms work with any standard outlet and also have a battery backup for continuous monitoring of CO levels, even if there's a power failure
• Features an advanced electrochemical carbon monoxide sensor that accurately detects carbon monoxide levels, no matter where the detector is placed in the room
• Simple to use, with a single test/silence button; a loud 85 decibel alarm sounds when Carbon Monoxide levels reach dangerous levels
• To ensure complete protection make sure to place 1 on each level of your home and in each bedroom
• 7 year limited warranty; equipped with end of life signal chirp, so you know when it’s time to replace the unit for safety
• All First Alert CO alarms are rigorously tested to meet UL standards

User questions & answers

Question:	Does the monitor plug directly into the wall socket or is there an electric cord
Answer:	This is not a plug-in. Operates on 3 AA batteries and acan be easily mounted on wall. Love it.
Question:	Will the unit work without a bettery in it
Answer:	The User's Guide for this product, and stamped on the item itself, are model numbers of alkalines, (Duracell MN1500 or MX1500; Energizer E91, etc). However, it does say "Use of a different battery may have a detrimental effect on the alarm operation." Thank you for calling my attention to this, because the rechargeables I use are NiMH. The item comes with batteries.
Question:	why does mine chirp intertmittently
Answer:	There is no installation required. Just put in the batteries as shown and it's ready to go. I move mine from room to room. You can mount it on a wall if you want.
Question:	I love the idea of plug-in without messing with batteries at all, but plug-is are only a foot of the floor. gas is lighter than air. would we be dead by the time the house is so filled it reaches clear down to the outlet? now leaning toward battery unit so I can place it high. opinions
Answer:	After spending 40+ years in the car business I have this to say: (everyone seems to be telling what they did or didn't do for a living 😉) I have that if you mount them from one foot above the floor, to one below the ceiling, or even on it..it is still better to have one than NOT to have one! No matter where it is!! It's like ANY tester or alarm, if you don't have one..that's when it will get you killed. Either way, most people will end up mounting them where they are out of sight. No matter what the papers or anyone tells you. Put at least one on each floor..and pray you never need them. Simple as that! Oh..the 40+ years in the car business Taught me this!l, Any idea how much CO is put out into the air of a car dealership over the course of each day, working on from 20-200 cars a day? A LOT! So again, mount it anyplace..but just MOUNT it! Good luck to you all. ;)

• ACCURATE & RESPONSIVE: With an advanced Figaro electrochemical CO sensor and high-performance ST chipset, the X-Sense carbon monoxide alarm instantly and accurately detects CO, an invisible, deadly gas, giving you the earliest possible warning of CO threat with both a loud 85 dB alarm and a rapid flashing red LED
• 10-YEAR 24/7 PROTECTION WITH REPLACEABLE BATTERY: Powered by 3 replaceable 1.5 V AA batteries and a 10-year sensor life, this CO alarm provides 24/7 protection, even during power outages; a low battery warning informs you when the batteries need to be changed, and an end-of-life warning lets you know when it’s time to replace the unit
• REAL-TIME CO LEVELS SHOWN ON THE LCD: Clearly displays the battery life and real-time CO levels taken from the surrounding air, with an updated measurement taken every 10 seconds; responds to various CO levels, with the lowest alarm threshold at 30 ppm, ensuring the ultimate CO protection
• EASY INSTALLATION: No need to worry about wires or wall outlets, as our battery-operated CO alarm is equipped with screws and anchor plugs, so you can install it easily and quickly wherever you want
• QUALITY ASSURANCE: Backed by a 60-day money-back and an incredible after-sales service team that will help you resolve any quality issues you have within 5 years; our lifetime technical support team will response to you within 24 hours

User questions & answers

Question:	Etl or ul listed
Answer:	Hello and thank you for your question, our product has two distinct layers. The outer layer is made from a thick liquid silicone coated fireproof cloth which gives our bag it's fireproof qualities. The inner layer is constructed from a thick PVC coated glass fibre cloth which gives our bag its water resistant qualities. When combined, these two layers provide excellent protection against, heat, direct flame, steam and water. If you check out the video in our listing, we show our rigorous house fire simulation testing to give people the reassurance that our bag can protect their important documents and papers. We are members of the Fire Department, so we are very strict with our materials and testing to ensure maximum protection. If you have any more questions, please feel free to let us know - we are here to serve you :) Thank you, Michael Team Alorva.
Question:	I want this because i burn wood in the basement, where would the best place to mount this? Close to stove or stairwell coming up the stairs
Answer:	Hello - the bag closes with a zipper and the top flap folds over the top and velcros in place for further protection. There is no lock. Thanks and if we can help you further please reach out. Thank you.

Product features

Technical Specifications

Power supply: 3 × 1.5V AA batteries

Quiescent current: <20 μA

Operating current: <45 mA

Best operating temperature: 40 to 100 ℉

Relative humidity in operation: ≤ 85% RH (non-condensing)

Alarm sound level:> 85 dB at 1 m

Low battery voltage: <3.5V

Product description

The Kidde KN-COPP-B-LPM battery operated CO alarm provides continuous monitoring of CO levels, even during power outages when many CO incidents occur. The digital display feature allows for easy viewing of carbon monoxide levels from 30-999 PPM (parts per million). The KN-COPP-B-LPM will also detect and istore concentration CO levels as low as 11 and up to 999 PPM with its peak level memory display. This alarm, includes a slide-out battery door that gives immediate access to the batteries and a safety feature that makes it difficult to close the cover without the batteries being installed. It has a 10-year life and a 10-year limited warranty.

Kidde’s KN-COPP-LPM battery-operated carbon monoxide alarm with digital display helps to provide your home with extensive protection against the dangerous threat posed by the odorless and colorless gas. With an increasing number of state and local governments passing legislation requiring CO detectors in homes, it’s never been a better time to safeguard your family against carbon monoxide exposure.

KN-COPP-LPM Battery-Operated Carbon Monoxide Alarm At a Glance: Digital display allows for easy monitoring of CO levels Battery operation provides best protection during power outages Peak level memory displays the highest CO concentration since last reset Dimensions: 4.5 inches by 2.75 inches by 1.5 inches; weighs .66 pounds with batteries Five-year limited warranty

Kidde's KN-COPP-LPM carbon monoxide detector is a free-standing unit, adding flexibility to placement around your home. View larger

Features

The KN-COPP-LPM is an essential device to help warn you and your family of dangerous carbon monoxide levels in your home. This alarm measures the exposure to carbon monoxide over time; it is designed to sound at 85 decibels at 10 feet when it detects 70 ppm (parts per million) of CO for 60 to 240 minutes, 150 ppm for 10 to 50 minutes, or 400 ppm for 4 to 15 minutes. The easily visible digital display indicates the level of CO that the unit is sensing, and it updates the status every 15 seconds for timely and accurate readings. Its free-standing design allows for attachment to a wall or placement on a counter or nightstand for convenient and comprehensive protection. The KN-COPP-LPM also includes a slide-out battery door that provides immediate access to the power source as well as a battery safeguard that makes it difficult to close the cover without batteries installed. An LED lighting system on the unit signals power levels and sourcing: the green LED will flash once every 30 seconds to indicate the alarm is operating properly when power is present, and the red LED will pulse to indicate carbon monoxide has been detected until the device is reset or the CO threat is eliminated. This device has an expected 7-year lifespan and comes equipped with a five-year manufacturer’s limited warranty.

What's in the Box

One Kidde KN-COPP-LPM battery-operated carbon monoxide alarm with digital display and three AA batteries.

The KN-COPP-LPM features an easy-to-read digital display in front and an easy-access door to the batteries in back. (Click each to enlarge)

From the Manufacturer

Kidde KN-COPP-B-LPM Battery-Operated Carbon Monoxide Alarm w/ Digital Display - Digital screen with large display is easy to read - Peak-level memory displays the highest CO concentration measured since the last reset - Meets the all UL requirements - Battery operated with three AA batteries included - Backed by a five-year warranty

The new Kidde KN-COPP--LPM carbon monoxide alarm is the only battery-operated alarm that includes a digital display feature. This key feature adds an advanced level of protection that you have come to expect in a Kidde manufactured product. The battery operated CO alarm includes multiple mounting options, allowing installation on a wall or tabletop. This alarm has been carefully designed and tested to detect CO concentration in a residential environment. It provides continuous monitoring of CO levels, even during power outages when many CO incidents occur. The digital display feature allows for easy viewing of carbon monoxide levels from 30-999 PPM (parts per million). The KN-COPP-LPM will also detect and store concentration CO levels as low as 11 and up to 999 PPM with its peak level memory display. This alarm includes a snap-on cover that gives immediate access to the batteries and a safety feature that makes it difficult to close the cover without the batteries being installed. Updates digital reading every 15 seconds, allowing you to see if levels change. The peak level memory displays the highest CO concentration measured since the last reset. The test/reset button tests CO alarm circuit operation and allows you to immediately silence the alarm. A low battery signal alerts users when the batteries need to be replaced. Includes informative LEDs: green LED for normal operation, red LED for alarm. The alarm alerts user to replace CO alarm after 7 years of operation.

Sensor: Electrochemical.

• Digital Display - Displays the level of carbon monoxide the unit is sensing. Shows CO level in PPM (parts per million). Updates digital reading every 15 seconds, allowing you to see if levels change. Peak Level Memory displays the highest CO concentration measured since the last reset
• Battery Operated - Provides the best protection during power outages. Battery safeguard makes it difficult to close the cover without batteries in the unit. Low battery signal alerts user when the batteries need to be replaced. Slide-out battery door cover gives immediate access to batteries
• Test/Reset Button - Tests unit’s electronic circuitry & horn and resets the unit during alarm. Tests CO alarm circuit operation and allows you to immediately silence the alarm
• LED's - Green LED for normal operation, Red LED for alarm. Temperature range 40˚F (4.4˚C) to 100˚F (37.8˚C). Sensor: Electrochemical
• Provides peace of mind against the silent killer and a digital display

User questions & answers

Question:	is it a plug in
Answer:	Light turns off on mine as well once i unplug but i just plugged it back in a tested it and it started beeping and went back to red
Question:	Can the alarm be run with rechargeable NiMH batteries
Answer:	The alarm never went off in ours and the battery was charged when we got it. Its a 10 yr battery so I think your product is defective.
Question:	how is it installed
Answer:	Not sure, but my suggestion would be to replace the battery. What good is a battery backup if your battery is low?
Question:	How is the unit mounted? Should it be near the ceiling or near the floor
Answer:	The plug also can be removed from the unit in case you want to mount the device on the wall or stand it on a table or night stand.

Product features

Digital Display

Displays the level of carbon monoxide the unit is sensing. The unit updates this reading every 15 seconds

Unmatched Protection

Be prepared for a hazard or emergency in your home, and ensure the safety of your family and loved ones with the Kidde carbon monoxide alarm. This CO detector uses advanced electrochemical sensors and features a digital display screen to accurately and quickly inform you of any CO levels in your home.

Protection Everywhere

This is a battery-operated, free-standing carbon monoxide alarm that can be placed on a counter, nightstand or tabletop, or it can be taken with while traveling or camping so that you can always be sure you are in a safe environment. Additionally, if it is your preference, it includes the hardware necessary for installation on walls.

Product description

The Kidde KN-COEG-3 AC powered, plug-in CO and explosive gas alarm protect you and your family from two deadly threats. The KN-COEG-3 includes 9V battery backup that provides protection during a power outage, when AC-only units cannot provide protection. By pressing the Peak Level Button you can see the peak CO level recorded by the alarm since it was last reset or unplugged. The continuous digital display shows you the level of carbon monoxide (if any) the unit is sensing as well as if gas is present. The gas sensor is a metal oxide sensor designed to detect natural gas (methane) or propane. Temperature range- 40 degree Fahrenheit to 100 degree Fahrenheit.

Protect your family from the dangers of carbon monoxide (CO), methane, and propane exposure with the Kidde KN-COEG-3 Nighthawk Plug-In Carbon Monoxide and Explosive Gas Alarm. The Nighthawk is an easy-to-install unit that provides reliable protection against the dangers of CO and explosive gas. The digital display shows if gas is present indicates CO levels in parts per million, allowing you to see if, how, and when levels change.

Advanced Technology in an Easy-to-Install, Plug-In Design

Designed for home use, the Kidde KN-COEG-3 Nighthawk is a UL-listed, A/C-powered, plug-in alarm that utilizes sophisticated electronic components and sensor technology to protect you and your family from the dangers of CO, methane, and propane exposure. It plugs directly into a standard A/C outlet and includes a 9-volt battery backup that provides continuous monitoring--even during power outages.

The Dangers of Carbon Monoxide, Methane, and Propane Exposure

The leading cause of accidental poisoning deaths in North America, carbon monoxide (CO) is often referred to as the silent killer because it's odorless, tasteless, and invisible. Carbon monoxide poisoning can come about via a number of sources, including everyday items and appliances in your home or office. And because symptoms of CO poisoning mimic the flu or other common illnesses it can often go undiagnosed.

Likewise, methane and propane gases are commonly used in homes for cooking, heating, and water heating. Although it happens rarely, gas leaks can sometimes occur inside the home, increasing the risk of fire or explosion.

Audible Alarm Pattern Alerts you to Elevated CO and Gas Levels

When placed on every level of your home, alarms like the KN-COEG-3 Nighthawk can help protect everyone in the house by giving you an unmistakable signal when gas levels have reached an unhealthy point. If unhealthy levels of CO are detected, the alarm will emit four quick audible beeps every five seconds until either levels decrease or the reset button is pressed. If methane gas or propane gas is detected, the alarm will emit beeps every other second with "GAS" shown in the display.

Easy-to-Read Digital Display Shows CO Levels

The KN-COEG-3 Nighthawk is preferred among traditional CO and explosive gas alarms because of its digital display. This display clearly shows levels of CO that the unit has detected and stored-- from 30 to 999 ppm--and it updates every 15 seconds to indicate any abrupt changes or alarming trends. The display also shows the peak CO level recorded by the alarm since it was last reset or unplugged. The continuous display also shows if gas is present.

LED Shows Sensor Status

With the KN-COEG-3 Nighthawk, you never have to wonder if the sensor is functioning properly. A blinking dot in the lower right-hand corner of the display denotes normal operation, so you can trust that it's working. In addition, you can test alarm function by pressing the test/reset button at any time to verify that the horn and electric circuitry are operating properly.

Convenient Mounting Options

The KN-COEG-3 Nighthawk has a low-profile design that makes it suitable for any room in your home. The detector can be plugged into any standard A/C outlet; it's plug can be snapped into the back of the unit and can be rotated so the alarm remains vertical, independent of whether the electrical socket is mounted vertically or horizontally. In addition, the alarm comes with a 6-foot extension cord, so the unit can be plugged into the wall outlet and then placed on a table or shelf. For the most thorough protection, place an alarm on every level of your home.

The UL-listed Kidde KN-COEG-3 Nighthawk has a seven-year life and is backed by a five-year limited warranty.

About Kidde: A UTC Fire and Security Brand

Renowned for global leadership in fire detection and suppression, Kidde provides solutions ranging from portable fire extinguishers to advanced industrial controls such as flame detection and explosion suppression systems. Kidde is a UTC Fire and Security brand, with a history that's rich with innovations, from the patent of the Chubb Detector Lock in 1818 to the development of the world's first wireless networked smoke detectors in 2004.

What's in the Box

Kidde KN-COEG-3 Nighthawk Carbon Monoxide and Explosive Gas Alarm, 9-volt battery, mounting hardware, and installation guide.

From the Manufacturer

The leading cause of accidental poisoning deaths in North America, Carbon Monoxide is odorless, tasteless and invisible. It is a silent killer. Kidde CO alarms include the most accurate sensing technology available, the patented Nighthawk electrochemical sensor. This unit is an AC powered, plug-in CO and explosive gas alarm that protects you and your family from two deadly threats. The 900-0113 includes 9V battery back up that provides protection during a power outage, when AC only units can not provide protection. By pressing the Peak Level Button you can see the peak CO level recorded by the alarm since it was last reset or unplugged. The continuous digital display shows you the level of carbon monoxide, if any. The unit is sensing as well as if gas is present. The gas sensor is a metal oxide sensor designed to detect natural gas , methane or propane. Install at least one CO alarm on every floor and in sleeping areas. Make sure CO alarms are at least 15 feet away from cooking or heating appliances to prevent false alarms. Replace CO alarms every 5 to 7 years to benefit from the latest technology upgrades.

• Protects you and your family from two deadly threats: Carbon monoxide and explosive gas.
• Sounder alarm – The KN-COEG-3 offers a loud 85-decibel pulsing alarm that will sound to alert you to a potential problem.
• Digital display - Displays the level of carbon monoxide the unit is sensing.
• Peak level memory - Recalls the highest CO concentration detected
• Test/reset button - Tests unit’s electronic circuitry operation and allows you to immediately silence the alarm
• Two alarms in one detects carbon monoxide and explosive gas
• Three convenient mounting options

User questions & answers

Question:	What is the sound level I need one for basement and need to hear on ground floor
Answer:	Dear cutomer, excuse that this prodcut Y301 can't detect hydrogen gas, it's mainly sensitive for methane and propane. thank you very much
Question:	is this an explosive gas and carbon monoxide detector? it only says "carbon monoxide detector" on the actual product
Answer:	Don't worry, it's normal, the large moisture change can affect the sensor performance, and may lead to false alarm, but the data on display only switch to 1,2 or 3, but won;t trigger the voice and light alarm. If the data become 5 or more than 5, voice and light alarm will be triggered. Thank you very much and best regards.
Question:	No manual included. Do I just plug it in and test it? What does it display if gas is detected? Thanks fellow Amazoners
Answer:	HI Niran, it's sensitive to methane and propane. We think it can't used to monitor and detect CO. thank you vey much
Question:	I smell natural gas in my house, and am wondering if that is the same as explosive gas? Will it detect natural gas
Answer:	Dear Karen, temporarily the Y301 doesn't get UL certification, it passed CE, FCC, EMC and RoHs. We are applying US ETL certification which is equivalent to UL certification. Thank you very much and best regards.

Product features

Plug-In Explosive Gas and Carbon Monoxide Detector with Battery Backup

The Kidde KN-COEG-3 AC powered, plug-in CO and explosive gas alarm protects you and your family from 2 deadly threats. The KN-COEG-3 includes 9-Volt battery back up that provides protection during a power outage, when AC-only units can not provide protection. By pressing the Peak Level Button you can see the peak CO level recorded by the alarm since it was last reset or unplugged. The continuous digital display shows you the level of carbon monoxide (if any) the unit is sensing as well as if gas is present. The gas sensor is a metal oxide sensor designed to detect natural gas (methane) or propane.

Carbon monoxide and gas detector plugs directly into wall outlet

Digital display updates CO level in PPM every 15 seconds

Loud 85 dBA pulsing alarm that will sound to alert you to a potential problem

• Combo smoke detector/carbon monoxide alarm detects two threats
• Electrochemical CO sensor alerts you to carbon monoxide danger
• Photoelectric sensor detects smoke while minimizing false alarms
• Battery-operated unit installs quickly and easily without an electrician，A single button tests the unit or silences the alarm. Low battery signal mute, quiets low battery signal for up to 8 hours
• 5 YEARS WARRANTY

User questions & answers

Question:	I cannot get power light to illuminate. Had smoke fill kitchen from pellet stove with no alarm from either device. Any tips
Answer:	Yes. VdS, TÜV Rheinland, BSI, ETL, and CCCF. UL 2034 (US) and EN 50291 (EU)
Question:	How does it show real time carbon monoxide levels and what not if the lcd screen does not stay on? Maybe I got a defective one
Answer:	Stairwell
Question:	Do theses need to be replaced in 5 years? it says 5 year warrnty some sy 7 some say 10yrs. what is the reccomendation on these
Answer:	Not thus far.
Question:	I cannot get power light to illuminate. Had smoke fill kitchen from pellet stove with no alarm from either device. Any tips
Answer:	Hello Bob, it's the Alorva team here. We do not provide moisture reduction packets, however, if you feel you need that added protection from moisture, feel free to do so. Some customers are constantly adding and taking out documents from their bags all the time and this airflow that is introduced is sufficient to keep moisture to non-existent levels. Thanks and have a Merry Xmas, The Alorva team.

Product features

Alerts You to Danger

When a threat is detected, the smoke and carbon monoxide alarm sounds a loud 85-decibel siren that is designed to wake even the soundest of sleepers.

A single button allows you to silence alarms and test if the device is working.

Battery Operated for Convenience

The battery-operated dual CO smoke alarm installs in minutes, without requiring an electrician. The unit requires two 1.5V AA battery and features a chirp and indicator light to let you know when they need replacing. The alarm mounts easily to a ceiling or wall and comes with pins to secure alarm to the base to prevent tampering.

Sleek, Low-Profile Design

Half as thick as a standard alarm, the Photoelectric Smoke and Carbon Monoxide Alarm packs premium detection features into a sleek, compact unit. The ultra-thin design features a white finish that blends seamlessly with most home decor.