13 best water heaters

• 🎁【CSA Approved Safety 】CSA approved Gasland tankless water heater, safe as per Canadian and US Standard. Flame failure device, anti-freezing protection, over heating protection to ensure the family safety. Automatically decrease water pressure between 2.5-110PSI. The anti-freezing drain plug can discharge the residual water to avoid freezing in cold areas or in case of long time no use. High water temperature protection over 167 °F. Shut off gas supply automatically under unexpectable flameout.
• 🎁【Lightweight Portable Design】 Compact size and lightweight design for easily carry. It can bring a amazing hot shower for you when you are camping, to the beach, etc. Also you can wash your pets with this tankless water heater in outdoor. Hang it using the mounting bracket on the top/back of the gas water heater. It only takes you a few minutes to install it. Or you can install it according to the instructions.
• 🎁【On Demand Hot Water】 Maximum power output 41,000BTU/Hr, get instant endless hot water easily wherever you are. No need to preheat before using tankless water heater. As soon as you turn on the tap, the water flows with your desired temperature. Low water pressure start up, just need 2.5 PSI of water pressure. 1.58 gallons per minute of on-demand hot water. Fully adjustable heat and water flow.
• 🎁【Energy Saving】 Compact and light weight structure with 11.5% energy saving technology. The propane water heater exchanger and main burner are desinged with advanced combustion technology to decrease gas consumption and burning noise. You will save more when you use our tankless water heater.
• 🎁【Excellent Customer Service】We have professional team to offer you excellent service. If you have any question, please feel free to contact us from Monday to Friday.

Product features

FEATURES

Gasland Outdoor BE158R 1.58GPM 6L outdoor portable tankless water heater has compact size and lightweight design allowing for a convenient carrying. Flame failure device, anti-freezing protection, over heating protection can ensure safety. With maximum power output of 41,000BTU/Hr and low water pressure start up of 2.5 PSI, it is the best solution for outdoor hot water. It is perfect for outdoor RV camping life or anywhere you need hot water.

Product Technology Specification

• Fuel Type: Propane(for propane only)
• Activation Flow Rate: 2.5PSI / 0.44GPM
• Maximum Power: 41000 Btu/Hr
• Flow Rate: 1.58GPM / 6L

Warm Tips

• When install the water heater please do not over tighten the connectors and pipes to prevent it from bursting and leaking.
• The exhaust and top will get hot, please check around area for flammables, especially gasoline or other vapors which may ignite. Please make sure there are no foreign objects around the portable tankless water heater or have fallen into the top.
• A gas leak detection is needed before use. Please do not use flame for leak detection. Soapy solution, gas detectors, etc. are recommended to detect leaks.
• Please use only liquid propane as fuel and use it in a well-ventilated place, do not use a natural gas.
• Please make sure there is enough water pressure. If the water pressure is below 2.5PSI, the water heater cannot be ignited.
• If the outside temperature is around or below 32℉/0℃, please ensure to drain out the water after each use to avoid internal damage to the heat exchanger.
• This water heater is not suitable for high altitude areas over 2000 feet and strong wind conditions.

Portable Handle

This portable gas water heater has a high quality handle. It is very convenient and portable for you to take when going outdoor to enjoy wonderful life.

Flame Viewing Window

You can view the flame through the flame viewing window in order to determine whether it is working normally. This can remind you if the fuel is enough or fully burned.

Energy Saving Knob

The middle knob above the LED screen is very useful. When you turn it to the "sunshine", only parts of the burners work to provide hot water, fits for summer use.

LED Display Screen

There is a LED digital screen in the middle to show the water temperature. It will tell you the exact water temperature to avoid avoid scalding by the hot water.

Multiple Daily Applications

• This portable gas water heater is the best choice for obtaining hot water when you go for a outdoor camping, RV life or anywhere you need hot water.
• This propane gas water heater is not suitable for drinking water but it is perfect for taking a shower for your pet dogs, horses and so on.
• You can build a well-ventilated private outdoor bathroom to take bath. It is not suitable for indoor use if a vent pipe is not used.

Lightweight, Portable

• This portable tankless gas water heater comes with a light weight around 10 lb and a reasonable size of around 17.3" x 11.8" x 6.1". This make it very compact and convenient to carry.
• This outdoor propane water heater also has a high quality handle. The metal handle is very convenient when you want to take this water heater together for an outdoor camping. Allowing to this portable design, you can take a hot water shower on your trip.

High Efficiency, Economy

• With a maximum outlet power of 41,000Btu/Hr, this tankless gas water heater can provide hot water on demand wherever you are.
• In summer, you can turn the middle knob above the LED screen to the "sunshine", only parts of the burners will work providing hot water. It's suitable for summer with a higher water temperature. When you turn to "snowflake", all the burners will work to provide hot water. It's suitable for winter.

Multiple Safety Protections

• CSA approved regulator make the gas water heater more safer.
• It will cut down the gas supply to ensure safety when flame out.
• The temperature sensor will detect the water temperature timely. It will shut down itself when reaches 167℉(75℃).
• The gas water heater will shut down itself while no water flows.
• Please open the drain plug to drain off the residual water when the temperature outside is below or nearly 32℉(0℃) or during non-use period.

BE158R 6L Propane Tankless Water Heater, Red

Product description

This water heater offers quick, continuous hot water that is on demand for single point-of-use or multiple applications.Robust copper immersion heating elements with brass top increases durability and are threaded for easy replacement. Digital temperature control allows you to set your temperature in increments of 1°

• External digital thermostatic control with LED display (+/1 degree accuracy)
• Most advanced self-modulation, adjust power to meet hot water demand
• Durable Copper immersion two heating elements, field Serviceable. Flow Rate- up to 4.4 GPM
• Simple installation – bottom 3/4 inch NPT water connections
• Threaded for easy replacement, simple installation, digital temperature display

User questions & answers

Question:	Can this be used in a recirculating system
Answer:	No where on the box does it say contains copper. Box reads.... 100% nonstick surface - hand washable and dishwasher safe- PFOAF Free, PTFE- fiberglass coating, safe up to 500 degrees, FDA approved. We are happy with our purchase.
Question:	How many amps
Answer:	Of course it can.
Question:	how many breakers and what amp
Answer:	No
Question:	will this supply two showers, washer and dishwasher for two people? (1000 sf house
Answer:	Made in China

• 【CONTINUOUS FLOW】Equipped with a 12KW high-power heating system, BIS12 is specially designed for bathing, which can automatically maintain water temperature for your constant comfort during bathing. If the hot water demand exceeds the capacity, simply set the temperature to 116°f or reduce the water flow through the water flow-regulating valve, and the hot water shower will never be interrupted. (116°f is the most comfortable temperature for bathing)
• 【SPACE & ENERGY SAVER】Mirror design provides aesthetic perception. The compact design not only saves space but also provides endless hot water for the whole house. The power output can be set through 9 temperature setting gears. When you don't need the water too hot, BIS12 can automatically change gears to reduce charge. It's 99.8% energy efficiency which can save a lot of electric charges.
• 【EASY OPERATION】 The water flow passes through the electronic flow sensor and then through the powerful cast aluminum internal heating system to achieve water and electricity separation, which is safer and more reliable. In addition, the corrosion inside the pipe is avoided to prolong the service life. No noise when in use, and it has the function of digital display and setting temperature memory.
• 【Power 12 PLUS】 The specific model of BIS12 is 12KW, 220V / 240V. It is recommended that the minimum requirement of household appliances is 100A, and the output water temperature is 86 ° f to 131 ° F. Each device is equipped with multiple protection devices and has been strictly tested to ensure 100% safety. The internal water and electricity are operated separately to avoid the hazards of leakage and fouling.
• 【WARRANTIES INCLUDED】BISELONG's top tankless instant water heaters have reached the highest standards of comfort and reliability. The purchase includes our 7-year leakage and 3-year parts warranty. Accessories include (2PCS 16"Long, 1/2"NPT stainless steel copper head hose, rain sprinkler, power wall, water flow valve).

User questions & answers

Question:	Water connections :1/2” npt. is this smaller than standard 40gal water heater connectors or same size
Answer:	No
Question:	What is the function of the part 'Anti electric wall'? What doe it do? Is it install on the inlet or outlet of the heater
Answer:	Requires two 40 amp breakers (80). Not 4 (160) you would only have room for this and an oven on 200 amp service. Also if you only have 100 amp service and don't want to upgrade to 200 amp, don't look at these.
Question:	What does a red line mean when you first power this heater on
Answer:	The RTEX-18 (240 Volt) requires (2) 40 amp breakers and 8 AWG wire.
Question:	Do you have a remote? Wifi? Range if inferred? Can it be controlled by a mobile device
Answer:	Hello- Sizing an electric tankless is very difficult. I always recommend that you call Rheem at 800-432-8373 to get a suggestion. I want to say this will only keep up with ONLY 1 source of hot water at any one given time. That being said, the RTEX-18 performance ( @240V )- 1.5GPM - 82degree rise 2.0GPM - 62degree rise 2.5GPM - 49degree rise 3.0GPM - 41degree rise So.... what it can keep up with all depends on: -the temp of water coming into the house -the flow rate of each faucet/shower head/washing machine/source of hot water -outlet temp desired I hope this helped :) Ben

Product features

Innovation, and Energy Saving

With more than 10 years of rich experience in the home appliance industry, BISELONG appliances have advanced technology, high-quality craftsmanship, reliability, and simple and easy-to-operate functional design, so as to provide you with a relaxed, efficient, and warm lifestyle. We are committed to innovation and based on consumer research and following strict quality standards, we provide user-friendly energy-saving equipment to meet your requirements at the best product.

We provide the equipment with a one-year Quality replacement, 7-year leakage, and 3-year parts replace. You don’t have to worry about quality problems. The equipment is a high-quality product, and we are full of confidence. If there is any problem, Our staff and technicians will be online 24 hours.

Bullet Points of BISELONG Electric Tankless Water Heater

Features

INSTANT ENDLESS HOT WATER - No need pre-heating and get hot water in seconds.

FLEXIBLE 360° INSTALLATION – Can be mounted in any angle, ideal for bathroom, kitchen, school, hospital and hair salon.

COMPACT SIZE - For indoor installation with compact and space saving design.

MULTIPLE SAFETY PROTECTIONS - Over temperature protection,Dry heating protection,Leakage protection,Water and electricity line separated.

Compact Design

Save space design, allows you install it in non-traditional spaces such as the utility room, basement, garage, attic, crawl space or even a closet.

Easy to read digital temperature display, no any complicated requirements for installation without minimal noise output.

Size: 11x2.7x18in

Weight: 10.95lb

Well sealed packaged that you can get a intact product, no any dented or damage.

Endless Hot Water

Not worry about the hot water even you have a long shower time.

No need to preheat, 3s you can get the hot water you want, no annoying delay and cold water.

Just turn on the tap or shower.

It can run both of our showers and dishwasher/washing machine without issue, up to 3 x faucet, 2 x shower at the same time.

Well suited also good for homes in the Northern U.S. and Canada or in the southern U.S. that have large Roman-style or Jacuzzi tubs that have generally more demanding water usage needs.

Good for Other Commercial Places

BISELONG Electric Tankless Water Heater not only for home use, but also for many other commercial places where need instant, endless and safe hot water, such as: apartment, barbershop, hotel, beauty salon, gym center, restaurent and so on.

More Smart Design:

--Mirror design, easy to scrub.

-Screen shows actual outlet water temperature clearly instead of the setting temp, safer

-Machine will auto stop if no water be heated.

-Adapt to 2 voltages: 240V/220V both ok, just 1 button to set it when install

-Cleanable filter

Suitable for all regions of the United States

It is important to figure out your average inlet water temperature, this determines if you can get hot water of desired temp from the hot water heater. Outlet water temp equals inlet water temp plus temp raise(by the hot water heater).

Test Data

Check the chart to figure out the flow rate suggested for your area and the corresponding outlet water temp to see if it meets your need. For example, if inlet water in your area is 67℉, you are able to get 1.6GPM hot water @ 121℉, if you set temp lower, you are able to get more than 1.6GPM, correspondingly.

Product Parameter

Determining specs and electrical infrastructure is important because without the correct infrastructure your unit may not fit onto your breaker panel. We would like to remind you of reading the user manual prior installation and using for the first time.

Product description

Get hot water where it's needed, when it's needed with the Bosch ES4 Tronic 3000 T Electric water heater. This 4-gallon capacity point-of-use mini-tank fits right under your sink and provides a practical and effective solution to your hot water needs. This smaller model can be plugged right into a 120-volt outlet with the 36-37" cord, or can be installed in-line with a larger hot water source to provide "on-demand" use. The glass-lined tank offers great insulation and added durability, while the heater's fast recovery rate eliminates long waits for hot water. An external dial allows you to easily control the temperature range, and the temperature-and-pressure relief valve enhances your safety. The ES4 Tronic 3000 T from Bosch has a sleek and attractive exterior design that blends in seamlessly with existing decor when installed in a visible location, making this heater a great option in any room. Water Heater measures 13.75" H x 13.75" L x 13.5" D and weighs 17.3 lbs. Do not operate this water heater if it is has a damaged cord or plug, if it is not working properly, or if it has been damaged or dropped

Manufacturer Contact Information

800-283-3787

• CONVENIENT HOT WATER HEATER: 4 gallon point-of-use mini-tank fits under your sink to provide hot water right where you need it. Thermal efficiency is 98%. Dimensions : 13.75 W x 13.75 H x 13.5 D Inches
• LONG LASTING QUALITY: This electric water heater is easy to maintain and has premium glass-lined material for a long service life. (Amps 12A, Volts (VAC) 120)
• INDEPENDENT INSTALLATION: 36-37" cord plugs into a 120 volt outlet for independent installation or in-line with a large hot water source
• FAST RECOVERY RATE: Eliminates long waits for hot water at your sink, get on demand hot water at your every need (supplies up to 2 sinks at a time)
• EASILY MOUNTED: Can be shelf, wall or floor mounted (bracket included); simply tap into the cold water line and install the water heater directly at the sink to provide hot water

User questions & answers

Question:	Is it necessary to connect an expansion tank to this heater (for safety purposes)? It states something to that effect in the user manual
Answer:	Yes, that is correct! Look for 1/2 to 3/4" hoses here on Amazon, or whatever you connection size is. They are very cheap and convenient here.
Question:	would this be able to supply a shower
Answer:	Installed at the outlet of the water heater, mainly to prevent electric shock, which is the second layer of protection
Question:	Can be used "in-line with a large hot water source"? Would it help a large bathtub that runs out of hot water before it gets full from main tank
Answer:	Should it be a white line? It means it has been powered on and can work after waiting for your settings
Question:	When this heater is connected to the hot water line, what happens with the cold water that was sitting in the pipes
Answer:	Dear Customer,  Thanks for your inquiry,BISELONG this water heater is not equipped with a remote control, you only need to adjust the temperature you want, generally do not need to adjust again.If you get any other question, please feel free contact us at [email protected] any time, we will do best to serve and help. Wish you pleasant shopping. Fly form BISELONG

Product features

Bosch ThermoTechnology

The Bosch Tronic 3000 T point-of-use electric mini-tanks are available in three compact sizes, which can be wall-hung (bracket included) or floor-mounted. They fit easily under a sink, even in a cabinet space, and because they have a sleek and attractive design, they blend in seamlessly with existing decor when installed in a visible location. Simply tap into the cold water line and install the water heater directly at the sink to provide hot water. Great for a wide range of locations!

Water Where You Need It

Provides hot water quickly at point of use and comes with temperature /pressure relief valve installed - 2.5 and 4 gallon tanks feature a simple 120 VAc plug-in connection (1440 watts).

Quality for Long-Life

Thick CFC-free foam insulation for maximum energy efficiency, glass-lined tank for durability.

Great for Small Spaces

Water heaters are compact and lightweight and can be floor, shelf, or wall mounted (except 7 Gallon) - features a sleek and attractive design to blend seamlessly with decor.

Minimize Wait Time for Hot Water

Waiting for hot water at a sink located far from a primary heating source can be frustrating. Only having access to cold water from a sink is just not useful, and plumbing a hot water line to every sink in a home or business requires time and money. To get hot water where it’s needed, when it’s needed, a better solution is to use the Tronic 3000 T from Bosch: a point-of-use electric mini-tank heater. This heater can supplement a primary water heating source, or be used under a single sink. In fact, the Bosch Tronic 3000 T can be used for three different applications: as a sole water heating source for a single sink, as a supplement to an existing heater located far from the sink, and as a buffer installed in-line with tankless water heaters that experience intermittent cold water, also known as 'cold water sandwiching'. No matter the configuration, there’s minimal stand-by loss from this premium mini-tank water heater.

Product description

This Smart Technology electric tankless water heater is configured as a "whole home" model for climates where incoming water temperature is 67°F and above. This model is well suited for heating up to 2-Gallon per minute, which is the equivalent of one shower head (with a 1.5 gpm flow) and one sink with a low inlet water temperature of 67°F and an output setting of 105°F. Digital Temperature Control allows you to set your temperature in increments of 1 Degree. This model can also be used in colder climates as a Point of Use for a sink or other low flow application. All tankless water heaters are sized based on flow rate and temperature rise, and there is a direct relationship between the two. So if used in a cold area requiring a high temperature rise, it will be more limited in the amount of fixtures (gallons per minute) it can heat at one time compared to a warmer climate. When sized properly this water heater will provide endless hot water and only consume the energy needed, giving the user complete control. Prior to purchase and installation please verify this model is the right size for the expected demand and electrical requirements. The ECO 11 requires a minimum 125 amp electrical panel for installation with 60 amp double pole breaker connected to set of #6 awg wire. Plumbing connections are 1/2" compression fitting with the option of 1/2" NPT adapter included. For additional assistance please feel free to contact our support center at 877-474-6473.



NOTE : 11Kw at 220 is equal to 13kw at 240. .Activation Flow : 0.3 GPM

From the Manufacturer

This Smart Technology electric tankless water heater is configured for climates where incoming water temperature is 67 Degree F and above. This model is well suited for heating up to 2-Gallon per minute, which is the equivalent of one shower head (with a 1.5 gpm flow) and one sink with a low inlet water temperature of 67 Degree F. Digital Temperature Control allows you to set your temperature in increments of 1 Degree. This model can also be used in colder climates as a Point of Use for a sink or other low flow application. Prior to purchase and installation please verify this model is the rights size for your hot water needs and electrical requirements.

• Lifetime warranty
• Save up to 60-percent on your water heating cost with an ECOSMART electric tankless water heater
• Never run out of hot water with an ECOSMART tankless water heater
• Patented Self Modulating Technology and design
• ECOSMART tankless water heaters are 99.8-percent energy efficient.Uniform Energy Factor:0.98

User questions & answers

Question:	Ours has only been in service for less than a year - will not adjust temperature to anything above 85 Deg. F. What do you think is the problem ? kds
Answer:	My only guess is that the rheostat (variable resistor) that the temperature adjustment knob is attached to may be faulty. If that isn't it then I don't know. Sorry.
Question:	The warrenty says that this unit must be installed by a licensed electrician and plumber, for them to honor the "life time warrenty." why
Answer:	Hello Bob, The reason is the same as why an innumerable number of gadgets around the world have that little "warranty void if removed" label. Because getting inside of one requires a certain level of training and expertise. Same with this unit. GadgetsGo is an authorized Ecosmart dealer. Kind regards,HenryGadgetsGo
Question:	My house is wired 110V. What additional items do I need to purchase for the conversion
Answer:	Just to expand slightly on prior answers, normally a residential service feed is 240 volts between the two incoming hot legs. There is also a neutral leg, which (hopefully) has zero potential with reference to ground. The voltage between either one of the hot legs and the neutral leg is 120 volts. The 120 volt circuits in your house are connected to one or the other of the two hot legs, and only one. An attempt is made to assign circuits to the two hot legs in a way that will roughly balance the load between them. The other side of a 120 volt circuit is connected to the neutral leg. There is additionally a safety ground run with the circuit, which also ties into the panel. Certain devices require more power (work product of current and voltage) than is practical to deliver using a 120 volt circuit. Common examples are your clothes dryer, and your electric stove. These devices are powered by both hot legs, with a difference in potential of 240 volts. This water heater is also such a device.STRONG BUT FRIENDLY WARNING: If you did not already know this, please don't make wiring this water heater your learning opportunity with electricity. Hire someone who knows how to do it right. Cutting corners, especially with higher currents and voltages, can lead to equipment damage, fire, and electrocution. Electricity is not magic, and you can certainly learn how to do many common wiring tasks safely on your own, but today is not the day to begin that journey. You need properly sized components, properly installed, and connected to an adequate service. Also, if you really, really foul up, you could conceivably wind up making that morning shower more energizing than you ever imagined, if you get what I mean. So newly aspiring electricians should go fix their grandmother's favorite table lamp instead. Once they have that working they can use it to to start reading books about electricity, residential wiring, and eventually, books about this stuff: http://amazon.com/s/ref=nb_sb_ss_c_0_8?url=search-alias%3Dstripbooks&field-keywords=nec+code&sprefix=nec+code%2Caps%2C164 . Of course, you still have to know not to nick conductors when you strip them, and other trade craft like that ; ) . Like almost everything in life that is fun, electricity will hurt you. Sort of like all those people you dated for a while, and then wished later you had never met.
Question:	what amp breaker is required
Answer:	The National Electrical Code requires conductors and overcurrent protection to be sized at 100% of the manufacturer's branch circuit recommendation for tankless electric water heaters. A 60 amp breaker is the same price as a 40 or 50, it is the wire that costs more. #6 AWG wire is required for a 60 amp circuit. If you undersize the wire it could overheat and catch fire. Protect your family and follow the manufacturer's sizing for this, or any other, electrical device. Your family's lives are worth the extra money. 

Product features

3 Smart Steps for Endless Hot Water

Step 1: Determining your average inlet water temperature is important, this allows you to determine how well your unit will perform in your desired location. A lower inlet water temperature will require a higher kilowatt product.

Step 2: Next you will determine how many applications your unit can run simultaneously at your chosen location inlet water temperature. Tankless electric water heaters are sized for maximum simultaneous use, not maximum fixtures in your home.

Step 3: Determining specifications and electrical infrastructure is important because without the correct infrastructure your unit may not fit into your breaker panel.

Product description

This Smart Technology electric tankless water heater is configured as a "whole home" model for climates where incoming water temperature is 62°F and above. The ECO 18 is capable of heating over 2.5 gallons per minute, which is the equivalent of one water saver shower head (with a 1.5 gpm flow) and one sink with a low inlet water temperature of 62°F, and an output setting of 105° F. Two showers emitting no more than 1.5 gpm each can be run simultaneously when incoming water temperature is above 70° F. Digital temperature control allows you to set your temperature in increments of 1°. All tankless water heaters are sized based on flow rate and temperature rise, and there is a direct relationship between the two. So if used in a cold area requiring a high temperature rise, it will be more limited in the amount of fixtures (gallons per minute) it can heat at one time compared to a warmer climate. However, when sized properly it will provide endless hot water and only consume the energy needed, giving the user complete control. Prior to purchase and installation please verify this model is the right size for the expected demand and electrical requirements. The ECO 18 requires a minimum 150 amp electrical panel for installation with 40 amp double pole breakers connected to sets of #8 awg wire. Plumbing connections are 3/4" NPT. For additional assistance please feel free to contact our support center at 877-474-6473.

From the Manufacturer

This Smart Technology electric tankless water heater is configured for climates where incoming water temperature is 62 Degree F and above. The ECO 18 is capable of heating over 2.5-Gallon per minute, which is the equivalent of one shower head (with a 1.5 gpm flow) and one sink with a low inlet water temperature of 62 Degree F. Two showers can be run simultaneously when incoming water temperature is above 70 Degree F in warmer climates such as South Texas, South Florida, New Mexico, Arizona and South California. These models come with a digital temperature control that allows you to set your temperature in increments of 1 Degree. Prior to purchase and installation please verify this model is the rights size for your hot water needs and electrical requirements.

• The product is highly durable
• The product is easy to use
• Manufactured in China
• Copper and stainless components
• Lifetime warranty for residential use
• Save up to 60% on your water heating costs with the most advanced, self modulating technology available
• Never run out of hot water with an ECOSMART tankless water heater.

User questions & answers

Question:	How do know which size to buy? We will supply two bathrooms, dish washer, clothes washer. What size should I choose
Answer:	I noted someone below stating they got the largest one and they can only run one water source at a time. My guess is they installed it wrong by not getting the electric hooked up right, or maybe the unit was just defective, or they live in Alaska. I went under size with an Eco 27 a few years ago because that’s all my electric panel could handle. We have zero issues in the summer. During winter months we can only run one shower at a time and have to slowly fill a tub (maybe 3/4 fill speed). To save as much money as I am on electric bill and have unlimited shower lengths (only 1 person at a time mid-Dec to mid-March) is totally worth it. On here today because I’m thinking of upping my panel size so was thinking of going with a larger one now. Regardless, CCRC’s experience with the largest unit not working is nothing like the experience I’ve had, and again I intentionally undersized mine for the house. The website has a clear chart to explain size you need based on number of water fixtures in your home and ground water temperature.
Question:	Can this unit supply a 3,700 sq foot home with 3 1/2 baths
Answer:	In the lower states it can, but in the northern states, multiple simultaneous users, it will be overloaded. If you can afford a 3,700 square foot home, then you can place a unit in each appropriate demand zone and be very glad you did. I love mine, live in KY, get great supply when the water is above 60 degrees, and then it slows the flow as the temperature drops. I have dishwasher, washing machine, garden tube, 2 showers, 3 sinks and 4 people. It is better than great in the summer, okay spring and fall, and we are conservative in the winter.
Question:	What is the power consumption of this tank-less heater
Answer:	The instantaneous power consumption while the hot water is running is quite high (up to 18kW or 27kW depending on which model you’re looking at on this page). However, when no hot water is being used, the power consumption is 0 (or a minuscule amount to run an LED light or something). The total power consumption over the course of several days or longer should be much lower than a tank heater but the short term power usage while the heater is making hot water will be much higher than a tank heater. It’s just that the unit sits idle most of the time while a tank heater will use power fairly frequently even when no hot water is needed as the water in the tank cools off over time and needs to be re-heater fairly constantly
Question:	remote
Answer:	This unit does not have the ability to have a remote temperature control.

Product features

3 Smart Steps for Endless Hot Water

Step 1: Determining your average inlet water temperature is important, this allows you to determine how well your unit will perform in your desired location. A lower inlet water temperature will require a higher kilowatt product.

Step 2: Next you will determine how many applications your unit can run simultaneously at your chosen location inlet water temperature. Tankless electric water heaters are sized for maximum simultaneous use, not maximum fixtures in your home.

Step 3: Determining specifications and electrical infrastructure is important because without the correct infrastructure your unit may not fit into your breaker panel.

Product description

Rinnai RU199iN Tankless Water Heaters, 11 GPM, RU199in-Natural Gas/11

• Endless hot water for your entire home
• RU199in Sensei SE+ Super High Efficiency Tankless Hot Water Heater - Natural Gas: Indoor Installation Only
• Up to 11 GPM hot water flow rate (varies by groundwater temp)
• Circ-Logic technology allows you to set recirculation patterns that coincide with your typical habits. Hot water is available when you need it!
• Residential Factory Warranty - 120 months (heat exchanger), 12 months (labor), 60 months (parts)

User questions & answers

Question:	How many BTUs
Answer:	The expansion tank for this heater is not required. Most people already have these installed in their homes but if not then it would be Ok without it as there is a pressure relief valve on top if something happened. GlobalTowne is an authorized Bosch distributor.
Question:	What recirculation pump will work with this heater
Answer:	A standard flow shower head is around 2.5 gallons per minute. A low flow head is around 1.5 gallons per minute. The recovery rate for a 90 degree temperature rise is 6.8 gallons per hour! So even the 7.5 gallon unit would only provide 4 minutes of shower time before the temp dropped off dramatically. (even at the low flow rate..)
Question:	What is wi-fi ready means and what what will you use it for ? also what circ-logic capable means? do you need recirculation pipe for it
Answer:	If your bathtub is bigger than your main heater tank, this unit isn't going to do much for you. It will add 2.5, 4, or 7 gallons to the capacity of your main tank, depending on which Bosch unit you buy. The 7 gallon unit requires a specially wired circuit. You will also get a little bit of lukewarm water that was in the line between your main heater and the Bosch unit. Unless your main tank is awfully small and your bathtub massive, the 4 gallon unit should work for you. Maybe a demand type thankless heater in your bathtub hot water feed would be a better choice, but be careful to size it properly for your desired flow rate and temperature rise. Also a tankless is likely to require special wiring.
Question:	Does this unit come with a vent kit? Thanks
Answer:	When the tap is opened, the hot water in the unit flows out. The colder water that was sitting upstream of the unit, enters the unit to be heated. If the tap remains open, the newly heated water flows out, being replaced eventually, (depending on the distance to the main water heater), with the water from the main water heater. You will probably set the unit temperature to equal the main water heater temperature, if you want to keep a constant temperature, but other scenarios are possible.

Product features

Endless Hot Water

Put an end to scheduling your hot water need.

• Never again choose between taking a piping hot shower, doing a load of laundry or running the dishwasher. A Rinnai Tankless Water Heater will never run out of hot water and leave you in the cold.

Hot Water On-Demand

Don't waste while you wait.

• Rinnai tankless water heaters with ThermaCirc360 technology recirculates hot water through your pipes to get you hot water fast.
• While you wait for hot water to travel from your old tank to your shower, you can waste the equivalent of twenty-four 16-ounce bottles of water every time. ─ that means an average of 8,700 bottles of water per person, per year.

Save Valuable Space

Your hot water heater doesn't have to be a behemoth!

• Compact design allows for installation in non-traditional spaces such as the attic, crawl space or even a closet.
• Save 16 sq. foot of space ─ the Rinnai tankless water heater is only the size of a small suitcase.

Affordable, Efficient Savings

Efficiency packaged in a compact design means cut CO2 emissions (as compared to tanks), use less energy and conserve water.

• Use 40% less energy than traditional tanks* because you heat water only when you need it.

100 years of Confidence

Get peace of mind with the unsurpassed quality and innovation of a Rinnai tankless water heater.

• Trust the #1 selling gas tankless water heating brand in North America for all of your water heating needs.
• Smart technological advancements such as WiFi monitoring, your trusted Rinnai service provider can monitor the efficiency of your tankless water heater and address issues before you ever experience a break in service.

Sustainable Reliability

It's a smart investment for now and the future when you intertwine sustainability and reliability.

• Every part of a Rinnai Tankless water heater is replicable so components can be easily swapped vs. buying a whole new system.
• Average life expectancy is 20 years vs. 8-10 for a traditional tank**
• With this premium product, you'll save–both money and worry–in the long run.

Product description

This electric tankless water heater is a true Point of Use Model because it is specifically designed for under the sink, single applications with a maximum flow rate of 0.5-Gallon per minute (gpm) and includes a 0.5 gpm sink aerator. This heater is flow controlled, meaning the temperature will adjust according to flow rate. It is the smallest sized Ecosmart electric tankless model and should not be used to run anything more than one sink at a time or used in areas where inlet water temperature is lower than 57°F. At this inlet temperature the ECO POU 3.5 can heat 0.5 gallons per minute to 105°F. Its compact size allows for under the sink installations. The Point of Use models are ideal for: Wet Bars, Strip Malls, Doctor's Office, Boats, Recreational Vehicles (RVs), Bathroom Sinks. When sized properly this water heater will provide endless hot water. Prior to purchase and installation please verify this model is the right size for the expected demand and electrical requirements. The Eco POU 3.5 requires a minimum 100 amp electrical panel for installation with 30 amp single pole breaker connected to #10 awg wire. Plumbing connections are 1/2" NPT. For additional assistance please feel free to contact our support center at 877-474-6473. TROUBLE SHOOTING STEP: When the water is not hot enough, please slow down the flow of water to increase temperature!

From the Manufacturer

This electric tankless water heater is a true Point of Use Model because it is specifically designed for under the sink, single applications with a maximum flow rate of 0.5-Gallon per minute (gpm) and includes a 0.5 gpm sink aerator. Its compact size allows for under the sink installations. The Point of Use models are ideal for: Wet Bars, Strip Malls, Doctor's Office, Boats, Recreational Vehicles (RVs), Bathroom Sinks. Prior to purchase and installation please verify this model is the rights size for your hot water needs and electrical requirements.

• Can provide hot water for one sink at 0.5 GPM in warmer climates
• Requires 1 x 30 amp breaker and 10 AWG wire
• For one sink at 0.5 GPM in colder climates the POU 6 is recommended
• Amperage Draw 29 amp. kW - 3.5 kW
• Connection Fittings 1/2" NPT

User questions & answers

Question:	Can the flow rate be adjusted up from 0.5gpm to say 1gpm or 1.5gpm (understood that the output water will be corresponding less hotter)? thanks in adv
Answer:	This is a 199,000 btu model, a 3/4" gas line is required to have sufficient gas supply.
Question:	degree water going in what degree will be at the tap
Answer:	rinnai recommends the GTK03 Grundfos kit for this unit
Question:	are any of these tankless water heaters plug in
Answer:	I think, you need buy a WiFi module, call Rennai and ask. Circ-logic did not work for me, I had to install re circulation pipe. Because of the high minimum flow requirements, this unit did not work with any regular re circulation pump, so wasted money buying a Watts pump. And paid double for the labor. Rennai told me that I should have bought their thankless heater with re-circulation built in.
Question:	Would you recommend this model for a shower in a guest bathroom
Answer:	IT CAME WITH ADAPTERS ON THE TOP. NO PIPING.

Product features

3 Smart Steps for Endless Hot Water

Step 1: Determining your average inlet water temperature is important, this allows you to determine how well your unit will perform in your desired location. A lower inlet water temperature will require a higher kilowatt product.

Step 2: This product is fixed flow, which means that the output temperature rise of this product is determined by flow rate of the application. This chart gives you the expected temperature rise for various sink flow rates from 0.5 to 1.5 gallons per minute.

Step 3: Determining specifications and electrical infrastructure is important because without the correct infrastructure your unit may not fit into your breaker panel.

Product description

This product has a 6-year limited warranty on tank and parts. It works effectively and is convenient to use as well. It is definitely a great quality product.

• Item Weight: 54.0 lb
• Country of Origin: United States
• Brand name: Richmond
• Item Dimensions: 19.0"L x 21.0"W x 26.1"H

User questions & answers

Question:	So where is the electrical cord on this water heater? I dont see any electrical connection on the picture showing
Answer:	No. This is a simple self- regulating unit. If you want more flow, and more hot water, go to the next size up that this company makes. I put this unit in my parents kitchen, where it doesn't get as hot and cannot cause burns. I have the larger unit in my kitchen. It can get very hot before it balances out.
Question:	What is amperage and how long does it normally take before it ships
Answer:	Hello James. Great question. This unit heats water by 24°F at a flow rate of 1.0 GPM (and a proportionately lower temperature rise with a higher flow rate, and higher temp. rise with lower flow rate). All tankless water heaters operate on the same principle. Therefore, you should add 24°F to your incoming water temperature of 60°F. The answer is 84°F. This heater requires one 00 amp double pole breaker. For a complete explanation of how to choose a tankless water heater, check out our blog post at blog.gadgetsgo.com/how-to-buy-an-electric-tankless-water-heater GadgetsGo is one of the first Authorized Ecosmart Dealers, since 2009. Kind Regards, John M. GadgetsGo
Question:	What is included with this purchase
Answer:	Hello. According to the NEC and building code, electric tankless water heaters 15 amps or above do not include a cord with plug. They must be hard wired to a junction box or breaker box. Feel free to ask us any other questions. GadgetsGo is one of the first Authorized Ecosmart Dealers, since 2009. Kind Regards, John M. GadgetsGo
Question:	Is there a 220V unit of this model available
Answer:	Probably not but can work if you live in a southern environment and can supply 10 gauge wiring (or whatever they specify) to it. I use mine on an outdoor shower to my pool area and works well, but you have to control the temperature by lowering the water flow thru to it. The first time I tried it, I had to actually remove the low flow stuff in the shower head because it was too hot but after I removed it its comes out a nice 100+ temperature straight out of the hot end. Note, if it is really cool in florida, this does not work real well because this particular model just doesn't have the wattage to heat up the water really well.I bought this primarily to heat my water at my kitchen sink and dishwasher and it does a fantastic job doing so as opposed to waiting a minute plus for water from the other side of my house to come. As a bonus, I also added an adaptor and run it out to a shower faucet for the pool and it works well for that also, but if you are in a cooler place than florida, I would encourage you to get something stronger because you will need to heat a lot more than 1/2 a gallon a minute or a gallon a minute flow rate that this really heats up.

Product description

Rinnai V53DeP Tankless Water Heaters, 5.3 GPM, V53DeP-Propane/5.3

• Endless hot water for your entire home
• V53DeP HE High Efficiency Tankless Hot Water Heater - Propane: Outdoor Installation Only
• Up to 5.3 GPM hot water flow rate (varies by groundwater temp)
• Control-R 2.0 mobile app features timers and schedules throughout the day and allows you to remotely put the system into vacation mode.
• Residential Factory Warranty - 120 months (heat exchanger), 12 months (labor), 60 months (parts)

User questions & answers

Question:	Can the temperature output be adjusted to 105F
Answer:	Sinks have aerators to slow down the water where a tub doesn't. It sounds like one possibility is that your exceeding the GPM for this heater. Next possibility, double check an measure your actually getting at least 240v at the heater, I had an issue where my unit was only getting 235v an it was causing a similar issue where only one of the two heating elements was activating. I had it set to 125F but it was coming out 100F. It was warm and without a meter I would of thought it was working correctly until I tried filling a tub. It couldn't even get the water warm. I pulled my wires out an restripped an cut an screwed them in an it fixed my problem, now its measuring around 245v. Make sure there is no copper showing after screwing down your input wires. Now filling the tub I noticed after about 10-15 seconds the water gets too hot to touch. I set it to 135F.
Question:	Can I use the Rinnai V65EP in Denver, Co? Temperatures during the winter can get below zero
Answer:	No tank, so, no overflow line required. It mounts on the wall. A pan is needed if required by building code in your city.
Question:	Does this unit come with controller? rinnai tech said i needed a mc-91-2us controller? do i need to buy separate
Answer:	good morning,60 amp breaker and , number 6 cable !thank you have a great day!
Question:	What does the "Low NOx Mean
Answer:	Hello-The RTEX-13 requires 1x 60A@240V breaker / 6 AWG recommended wire size.Specs - http://cdn.globalimageserver.com/fetchdocument-rh.aspx?name=Specification-Sheet&id=fc3235b7-7cd0-42cd-93bc-7169ea92be31 Rheem 800-432-8373I hope this helped :)Ben
Question:	We have a 500sq' apt. 1 kitchen sink, 1 lav sink and tub/shower. This tankless heats water to both sinks but nothing to the tub/sh. Help
Answer:	It’s next to the side cover on the front of the picture shown. The circle next to the cover is the hole for the 3/8 fitting and wire to go through.
Question:	Do these tankless water heaters require an overflow line to the outside of the home or a pan like is required on normal water heaters
Answer:	I believe it draws nearly 1800 watts ( 15 amps at 120 volts). Mine took about 6 days to arrive at a rural location in Central Wisconsin.
Question:	what are the wiring and power requirements
Answer:	To be honest I would not buy it. It came dented like it fell off the. Truck.. No support from ups, amazon or manufacture . I had no choice but to install it. Holding my breath.... It's up to you..... it came bare bones....
Question:	How many amps are needed for rheem rtex - 13 240v heating tankless electric water heater
Answer:	Not a 220v. This is 2000 watts, 120 volt //Amps 16.67 (20 amp)

Product features

About Us

Brothers Richard and Donald Rheem founded Rheem Manufacturing Company in Emeryville, CA, in 1925. While the company has produced a number of products in its nearly 100 years of operation, Rheem is currently the manufacturer that produces heating, cooling, water heating, pool & spa heating and commercial refrigeration products, and it is one of the largest manufacturer of water heating products in North America.

Endless Hot Water

Put an end to scheduling your hot water need.

• Never again choose between taking a piping hot shower, doing a load of laundry or running the dishwasher. A Rinnai Tankless Water Heater will never run out of hot water and leave you in the cold.

Hot Water On-Demand

Don't waste while you wait.

• Rinnai tankless water heaters with ThermaCirc360 technology recirculates hot water through your pipes to get you hot water fast.
• While you wait for hot water to travel from your old tank to your shower, you can waste the equivalent of twenty-four 16-ounce bottles of water every time. ─ that means an average of 8,700 bottles of water per person, per year.

Save Valuable Space

Your hot water heater doesn't have to be a behemoth!

• Compact design allows for installation in non-traditional spaces such as the attic, crawl space or even a closet.
• Save 16 sq. foot of space ─ the Rinnai tankless water heater is only the size of a small suitcase.

Affordable, Efficient Savings

Efficiency packaged in a compact design means cut CO2 emissions (as compared to tanks), use less energy and conserve water.

• Use 40% less energy than traditional tanks* because you heat water only when you need it.

100 years of Confidence

Get peace of mind with the unsurpassed quality and innovation of a Rinnai tankless water heater.

• Trust the #1 selling gas tankless water heating brand in North America for all of your water heating needs.
• Smart technological advancements such as WiFi monitoring, your trusted Rinnai service provider can monitor the efficiency of your tankless water heater and address issues before you ever experience a break in service.

Sustainable Reliability

It's a smart investment for now and the future when you intertwine sustainability and reliability.

• Every part of a Rinnai Tankless water heater is replicable so components can be easily swapped vs. buying a whole new system.
• Average life expectancy is 20 years vs. 8-10 for a traditional tank**
• With this premium product, you'll save–both money and worry–in the long run.

• 2 PCs 16” long 1/2”FIP x 1/2”FIP,Stainless steel water hoses ,Vent valve,included
• 【NOTE】The cold water pipe has a safety valve, which is marked with a water pressure of 0.75MPa. When the water pressure in your home is greater than this value, the safety valve will automatically drain. At this point, you only need to contact us, we will send you a 0.9MPa exhaust valve, you can solve this problem
• 【SAFE DURABLE & LONGEVITY】Made of stainless steel and never rust，Anti-leakage plug，Multiple safety protection functions protect you from the risk of scald, leakage or other injury.Premium plastic shell is corrosion resistant，This mini hot water heater is ideal for kitchen, bar, school, hospital, community and RV.
• 【SMART INVERTER FOR ENERGY SAVING】Automatic heat preservation and storage of hot water, 2.5 gallon point-of-use mini-tank fits under your sink to provide hot water right where you need it. Thermal efficiency is 98%，Maximum temperature167℉，The built-in smart chip heats up to the temperature you set, and automatically Insulation when heated to the specified temperature.
• 【EASY TO USE】storage tank electric water heater with easy-to-operate knob temperature adjustment design，Easy to control warmth.Vent valve, Tee pipeline， pipes and other accessories are complete for quick installation without additional expenses or preparing time of accessories.
• 【FAST RECOVERY RATE】Eliminates long waits for hot water at your sink, get on demand hot water at your every need (supplies up to 2 sinks at a time，8-15 minutes to heat to your desired temperature).
• 【COMPACT DESIGN】Can be shelf, wall or floor mounted (Water inlet and outlet upward); Dimensions: 13.0''L x11.4''W x10.6''H; 9.5lbs; 1/2″NPT NPT. 1.5 kW, 110-220 volts. One-year warranty and 24H customer service support, feel free to contact us.

User questions & answers

Question:	How is it that this is energy efficient if it constantly maintains a heating temperature that you can use on demand? Is there an off/on switch
Answer:	Most rinnai tankless weather it is out door or indoor, have a control board to adjust temp and either on or off
Question:	I connected the water in the water heater already. But the pressure didn’t pumt the water to the sink
Answer:	It can definately be out doors in freezing temps, tho power failure arent good for it while in a freeze, tho keep in mind it will use alot more energy for frost protection, indoor units are safer amd more efficient in this case
Question:	Can I connect the water intake on this unit from the hot water supply from my house water heater? The house heater is very far from kitchen sink
Answer:	I bought model V65EN. It came with a wired digital controller. The installer did not run the wire into the house and mount the controller indoors. He simply set the controller at 120 degrees and left the controller inside the unit. If I want to change the temp, I have to take the cover of the unit.
Question:	Will this work for an outdoor shower
Answer:	Good place to check for info like this is Wikipedia. Here is what they say: Energy efficiencieseditMore tangible cost savings are defined when comparing the energy efficiencies of gas heaters with low NOx emissions with conventional flued types. Gas heaters with emission problems are flued and inherently lose substantial energies in the form of hot flue gases to the atmosphere. In addition, the choice of placement of flued heaters is greatly impaired due to flue installation restrictions.In contrast, dedicated low emission gas heaters do not require a flue system. Furthermore, with the introduction of oxygen depletion sensors and thermostatic controls, they do not place critical reliance on ventilation as previously was the case. These heaters can be positioned more conveniently and centralised to affect optimum warm air distribution. By definition unflued low NOx gas heaters are 100% efficient as all heat energy released from the flame is converted to useful heat.Hope this helps. June

Product features

BIS 1.5Kw Mini-Tanks Water Heater Electric

Features

Saves Energy and Money - No need to preheat before using,no any waste for water or electricity.

Endless Hot Water - Maintenance-free bare wire heating systems.Depending on the region, the water temperature can be heated to 167℃ within 8-15 minutes.

Space Saving - Very compact designed, which can be wall-hung (bracket included) or floor-mounted，easy to install.

Hot water on call

Waiting for hot water at a sink located far from a primary heating source can be frustrating. Only having access to cold water from a sink is just not useful, and plumbing a hot water line to every sink in a home or business requires time and money. To get hot water where it’s needed, when it’s needed, a better solution is to use the BISELONG: a point-of-use electric mini-tank heater. This heater can supplement a primary water heating source, or be used under a single sink and double sink. In fact, the BISELONG can be used for three different applications: as a sole water heating source for a single sink, as a supplement to an existing heater located far from the sink, and as a buffer installed in-line with tankless water heaters that experience intermittent cold water, also known as 'cold water sandwiching'. No matter the configuration, there’s minimal stand-by loss from this premium mini-tank water heater.

INSTANTLY HOT WATER

As soon as you open the tap, the water flows with your desired temperature. The water is only heated in the amount and for the time you actually need it.

ENERGY EFFICIENT

It saves energy by producing hot water only when needed. Instant hot water flows out at anytime you need.

KNOB ADJUSTMENT

Equipped with a Knob adjustment control for stable temp. easy and convenient. Just turn the knob to the maximum and submit the temperature suitable for you through the faucet，Optimal energy efficiency is promised.

GREAT FOR SMALL SPACES

Water heaters are compact，It can be installed under the sink features a sleek and attractive design to blend seamlessly with decor, very friendly to any small spaces.

• 【INSTANT & SUFFICIENT HOT WATER】 Applied with 9kW heating system, the electric water heater ECO90 supplies instant, consistent and endless hot water of 116℉or higher temp shortly, no waiting for preheating nor temp fluctuations in use, perfect companion for sink and faucet.
• 【SMART SELF Modulation】The hot water heater ECO90 adjusts power input according to flow rate and temp setting in real time, less power will be applied by the system when waterflow reduced, thus you still get ideal temperature instead of scalding hot water, which means comfortable experience. Optimal energy efficiency of 99.8% saves considerable electric charge.
• 【UPGRADED HEATING ELEMENT】The ECO90 hot water heater is applied with micro-computer control and patent heating technology. Water pipe is completely separated from electricity by cast aluminum module, which also guaranttes no"cold water sandwich" and avoids any corrosion inside pipes so as to extend service life.
• 【SAFE AND DURABLE】Applied with multiple protection devices, every unit goes through strict tests to ensure 100% safety. Inner water and electricity lines are designed to run separately so as to avoid leakage or harm of scale build up. Approval by ETL and qualifies for UL, you can expect outstanding performance for years to come.
• 【CONVENIENT USE】The ECO90 tankless water heater comes with digital display & touch control panel so temp setting is easy job. It's space saving, measuring: 15.8″ H x 11.1″ W x 3.1″ D. Plus it has a stylish, modern design that blends in any location. Please verify it is the right size for you: 9kW@240V (not 110V); pipes fittings : 1/2" NPT.

User questions & answers

Question:	Is a pressure relief valve needed for the electric tankless water heater
Answer:	Of course there is a switch
Question:	is the tankless water heater electric suitable for a shower without hot water feeding in
Answer:	Chances are there is a check valve and the lines are connected backwards if pressure is not making it to your sink. Make sure you connected the line into the heater on the right side where the blue cap was. The line out comes out the left where the red cap was on the heater. Do expect some reduction in pressure, but it should not be excessive.
Question:	Will this unit work in a 15 gallon closed loop recirculating system that needs to stay at a constant 100 degrees +/-3 degrees
Answer:	Yes you can connect this unit to the hot water supply line from your existing hot water heater and have hot water delivered to your kitchen sink. This unit will reheat the hot/warm water to the desired temperature. This should ensure you have continued hot water.
Question:	will the electric water heater tankless work under low temp condition
Answer:	If you take a Navy shower, as in turn on water rinse, off while washing self, turn water on to rinse. Would need to be a short shower overall but it could work.

Product features

INNOVATION, OPTIMIZATION, ENERGY-SAVING

With rich experience of 20 years in appliances industry, ECOTOUCH appliances is associated with advanced technology, quality craftsmanship, reliability and attractive features design, which offers brand new life style of being easy, efficient and enthusiastic. We are decicated to innovate and offer user-friendly & energy saving appliances that base on extensive consumer research and follow stringent quality stanards, meeting your requirements at the very best value for your budget.

We offer 1 year QA for the unit and you don't have to worry about any quality issue, the unit is premium quality and we have full confidence on it. If anything unexpected occurs, we get technicians to figure out the issue and offer you the best solution.

Electric Tankles Water Heater for Your Dear Family

Being one of those limited choices with smart modulation heating, ECOTOUCH ECO90 tankless water heater provides instant & endless hot water with optimal thermal efficiency of 99.8% and minimum energy cost, thus, the tankless water heater heats up 1.5GPM water from 67℉ to 106℉ and will sure cut your electric bill.

Designed with sturdy structure, it is a perfect solution for kitchen & bathroom sinks, dishwasher and washing machine and you could use it for shower purpose in southern area.

Instant hot water and endless

As soon as you turn it on, hot water comes out immediately with desired temperature and sufficient flow rate of 1-1.5 gallon per minute, no waiting for preheat or standby energy loss. The best part is you get endless hot water now, 24h service, anytime you need.

Smart modulation and energy saving

Equipped with a smart modulating control for stable temp, the hot water heater adjusts exact power input according to power calculation based on flow rate and temp setting in real time, which means you get still stable temp, instead of scalding hot, when you reduce flow rate. Optimal energy efficiency is promised.

Easy to installation

Wall-mounted design frees up floor space for more storage, easy installation in bathrooms, kitchens. Totally silent operation and no venting is required. It is also ideal for apartments as well as a wide range of business and industrial applications.. you don't to have to hire a plumber even if you can do it.

• ***Kit requires 2-3 gallons of white vinegar*** Not included. Some tankless manufacturers recommend using vinegar or another cleanser for flushing their equipment. Can also save money if you have vinegar at home already.
• Helps maintain the performance and extend the life of your tankless hot water heater. Easy directions for DIY Homeowner use.
• Includes 1/8 HP Utility Pump, 6 Ft Color Coded Hoses, 3.5 Gallon Bucket with EZ Open Lid & Instructions for using vinegar. Peel Off Lid is super flexible and much easier to remove than traditional paint bucket lids.
• Easily connects to tankless isolation valves using supplied 6' Color Coded Hoses.
• Works with Rheem, Bosch, Noritz, Rinnai, Takagi, Navien, Stiebel, Atmor, Ecosmart, Eccotemp, Marey Power, Tempra, Trutankless and others.

User questions & answers

Question:	i use vinegar but pump was damaged because of acid, that means every time i want to flush, i have to buy a new kit
Answer:	Dear Valued Customer, Thank you very much for your trust in ECOTOUCH and we would like to clarify that you don't need press relief valve to work with the ECOTOUHC tankless water heater electric, because it could handle wide range water pressure. However, we would suggest flow rate of 0.6-1 GPM flow rate for desired outlet water temp from the tankless water heater. You need a tap or a water valve to do easy water flow rate control. If you get any other question, please feel free to contact our customer service mail:[email protected], we will do best to serve and help. Wish you pleasant shopping experience. Best regards Christina from ECOTOUCH
Question:	Does it work with Richmond tankless
Answer:	Dear Valued Customer, Thanks for your trust in ECOTOUCH Appliances and we would like clarify that the ECO90 tankless water heater electric is mainly designed for a single sink use, with flowrate of 0.8-1.2GPM suggested. And you may need hot water of 1.5-2GPM with with decnet outlet temp for a shower, so the ECO90 hot water heater works for shower prupose in South US, with warm inlet temp, and you should get a 13kW unit at least for shower purpose in the northern part. If you get any other question about use of the unit, please feel free to contact our Customers service: [email protected], we will put your case in priority and do best to serve. Wish you pleasant day. Christine from ECOTOUCH
Question:	How many gpm or gph? my noritz tankless heater requires pumping for one hour at 4 gpm
Answer:	Dear Valued Customer, Thank you very much for your trust in ECOTOUCH, we would like to tell you that the tankless water heater electric ECO90 gets a smart heating system of self modulation inside, that helps to keep stable temp. So,we believe it will work great for you. However, we would like to remind you that, the electric hot water heater should not keep working for more than 2 hours, it is not specially designed for the purpose after all. If you get any other question, please feel free to contact us via: [email protected], we will do best to help and serve any time necessary. Wish you pleasant shopping. Best regards Christina from ECOTOUCH
Question:	What type of vinegar do I use? Distilled 5%? 30%? Concentrated
Answer:	Dear friend, Thanks for your trust in ECOTOUCH Appliances and we would like to tell you that the tankless water heater electric ECO90 works properly under all temp condition, except freezing cold with ice. And if you need to it to work with cold temp water inlet, we would like you to check the chart for temp rise with flow rate to ensure you could get desired outlet water temp with sufficient flow rate. If you get any other question about use of the unit, please feel free to contact our Customers service: [email protected], we will put your case in priority and do best to serve. Wish you pleasant day. Christina from ECOTOUCH

Product features

Kelaro Tankless Water Heater Descaler Kit - Just add Vinegar

Like all appliances, tankless water heaters require regular maintenance for optimal performance and efficiency. With proper maintenance, they can last over twenty years.

This cleaning kit comes with everything you need to maintain your water heating system. It includes step-by-step instructions that are easy to follow and quickly connects to your tankless isolation valves using the supplied hoses. Just add your own vinegar.

Mineral Build-up is Bad

Heater elements attract minerals from water and quickly add layers of scale during normal use. The layers get caked on and decrease the surface area available to heat up water.

Avoid Cold Showers

Scale build-up causes water to heat slower and decreases the maximum temperature of water coming out of your heater.

Scale will keep adding layers until the system is no longer able to heat water going through your tankless water heater - meaning cold showers are in your future!

Save Cash

Tankless water heaters don't run efficiently with scale and require more energy (gas or electricity) to run. Extra energy costs add up month after month.

You could hire a plumber to do the maintenance, or save even more - and do it yourself.

Annual maintenance using a Kelaro Flush Kit keeps your system running efficiently and saves you energy. Even better, the kit can be reused year after year - just replace the cleaning agent.