6 best compound mitre saw

Product description

The DEWALT DWS779 12" Sliding compound Miter saw features a powerful 15 amp, 3,800 RPM motor that delivers extended power and durability. It has a super-efficient dust collection system that captures over 75 percent of dust generated. This miter saw also offers an exclusive back fence design which cuts up to 2x14 dimensional lumber at 90° and 2x12 at 45°.

• Your purchase includes: 1 CDEWALT DWS779 sliding compound cord miter saw, 12-inch, carbide blade, 1 blade wrench
• Tool dimensions: 17” H x 24.75” L. Tool weight: 56 pounds; Maximum cutting thickness: 6.75 inch
• Other specifications: 15 Amps, 12” blade diameter, 5/8” or 1” Arbor size. 3800 RPM motor. Type of milter saw: Slide
• Exclusive back fence design cuts up to 2x14 dimensional lumber at 90 degree and 2x12 at 45 degree. Miter saw does not come with LED (sold separately) or laser cutting guide
• Super-efficient dust collection system captures over 75 percent of dust generated
• Backed by Dewalt's 3 year limited warranty

User questions & answers

Question:	Is the current model that is shipping type 1 or type 20. If you look up the parts diagram the type 20 has a different slide mechanism part number
Answer:	I bought a new one today from a lumberyard and it is a Type 1. (says right on the sticker on the motor) Not sure if that means the slide mechanism is better or worse than the Type 20. I would assume it was made in 2014 because there is a "Dewalt use only" tag on the box which starts with 2014. Not sure if a "fresher" saw is a Type 20
Question:	Can xps be added, i know dewalt makes a kit to add it to some saws, but this model was not listed
Answer:	mmToolparts actually sells a kit (3 proprietary DeWalt parts + their wiring harness) for less than $70. They have videos on their website that show how to install the parts on DW716, DWS779, and DWS782 saws. You will need some additional tools (torx screw drivers or torx bits, wire strippers/cutter/crimper) and somewhat mechanically inclined. Just google "DWS779 xps light kit" and they should be the top result. This might be an easier option versus going to a DeWalt service center in the post pandemic world.
Question:	Does this miter saw come with a laser or any guiding system
Answer:	It does not come with any laser for guidance. You may find my answer a bit crude, I've been using miter saws for many years and the best guiding system I found to work is my/your eyes. Having lasers or no lasers you still need to use your eyes to get the work piece spot on near the cutoff point. Hope this helps!
Question:	Is there an LED cut line
Answer:	You can add the LED light to this saw. Not a laser but a shadow light that show exactly where the saw blade will cut. I just did it last night. Parts can be had for about $70. This basically turns it into a model 780 which is much more expensive. Pretty simple to add.

Product description

The Metabo HPT C10FCGS 10-inch Compound Miter Saw is lightweight for easier transport. The 15 amp motor generates a no-load speed of up to 5000 RPM for making crosscuts and miter cuts with ease. This miter saw offers a bevel range of 0-45 degrees to the left to provide clean and accurate bevel cuts. It is designed for woodworkers who demand precision, reliability and versatility on the job.

• 10" Compound Miter Saw
• MOTOR: 15 Amp motor delivers high power for the toughest of cuts generating a no-load speed of up to 5,000 RPM
• LIGHTWEIGHT: Only 24.2 lbs. to facilitate maneuverability and portability
• MITER ANGLE RANGE: 0-52 degrees, to the right and left for increased flexibility
• BEVEL RANGE: 0-45 degrees, to the left with adjustable bevel stops for precision cuts
• LARGE TABLE: Offers better material support with vice clamping system to secure work piece
• THUMB ACTUATED POSITIVE STOPS: For quick miter adjustments

User questions & answers

Question:	Does this take any 10” blade
Answer:	Yes, it will take any 10" blade with a 5/8" arbor.
Question:	does this come ready to use or is assembly required
Answer:	Hi there, there is a small amount of assembly required. Please refer to the owner's manual for setup instructions. Hope this helps!
Question:	Is the depth of cut adjustable
Answer:	Depth can't be adjusted on this model number. You will need a sliding compound miter saw.
Question:	According to the instruction manual, the item includes a 10mm box wrench to tighten the nylon nut M6 for the sub fence installation. I used my own too
Answer:	Yes, but using yours is fine. Theirs is included simply for convenience if you didn't have one.

Product features

45 Degree Bevel Range

To the left to provide clean and accurate bevel cuts

Horizontal handle

For a secure hold

15 Amp motor

Delivers high power for the toughest cutting jobs

Large table

for better material support with vice clamping system to secure work piece

Product description

The DWS713 10 in. Compound Miter saw has a 15 amp motor to drive 5, 000 RPM, delivering Extended power and durability. Features stainless steel Miter detent plate and turn knob lock that provide repeatable accuracy and durability with easy adjustments. Tall sliding fences support 4-1/2 in. Of crown molding vertically nested. Lightweight design and built-in carry handle for portability.

• Stainless steel miter detent plate with 14 positive stops
• Precise miter system and machined base fence support
• Tall sliding fence supports 4-1/4 in. Base vertically
• Bevels 0° - 48° to the left and 0°- 3° to the right
• 2 in. X 6 in. Dimensional lumber cross cut capacity at 90° and 2 in. X 4 in. Dimensional lumber at 45°

User questions & answers

Question:	Is there a built in clamp so the wood can be clamped to the fence
Answer:	There is no built in clamp.
Question:	How can you attach a temporary wood fence for clamping on a work stop? It look like you can't attach on the right
Answer:	Mounting holes are provided in all four feet to facilitate bench mounting. There are round countersunk holes for use with screws and square holes for use with the miter saw stand "carraige bolt" or M8 (5/16") or smaller bolts. Use either hole, it is not necessary to use both. Always mount your saw firmly to prevent movement. To enhance the tool’s portability, it can be mounted to a piece of 1/2" (12.7 mm) or thicker plywood which can then be clamped to your work support or moved to other job sites and reclamped. NOTE: If you elect to mount your saw to a piece of plywood, make sure that the mounting screws don’t protrude from the bottom of the wood. The plywood must sit flush on the work support. When clamping the saw to any work surface, clamp only on the clamping bosses where the mounting screw holes are located. Clamping at any other point will surely interfere with the proper operation of the saw. CAUTION: To prevent binding and inaccuracy, be sure the mounting surface is not warped or otherwise uneven. If the saw rocks on the surface place a thin piece of material under one saw foot until the saw sits firmly on the mounting surface. Be sure all blade and blade clamps are clean, recessed sides of blade clamps are against blade and arbor screw is tightened securely. Loose or improper blade clamping may result in damage to the saw and possible personal injury.
Question:	Will the included blade cut aluminum; or is there a different blade available for that purpose
Answer:	Yes, the blade will cut aluminum; however, is not designed for aluminum and I'm sure there are some pieces of aluminum, such as very thick pieces that could destroy the blade or the saw. Look for a blade better suited to the material you are intending to cut.
Question:	Can I cut 4x4 stock with this in a single pass
Answer:	Yes. That would be completely within the capabilities of this saw. I used this model to cut 4x4 for legs of a table just a month ago no problem.

Product description

The Makita 10” dual-bevel sliding compound Miter saw with laser (model LS1019L) delivers large cutting capacity and accuracy right out of the box. With the LS1019L, you'll get all the cutting performance you need in a slide compound saw, but with the most compact size in the Category for increased portability. With up to 6-5/8” capacity (crown molding, nested) jobs like cutting baseboards and crown molding are a snap, but with up to 4-3/4” baseboard, capacity, it can cut 4x4 dimensional lumber in one pass. It's ideal for fine woodworking, carpentry, general construction, and more. The LS1019L is powered by a 15 amp direct drive motor with soft start, a key point of difference. This means smoother start-ups and consistent, Constant power with No belts to slip or replace. The Electric brake provides added convenience. The LS1019L will tackle the most demanding jobs while keeping production high.

• 10" slide miter saw with the Crown molding cutting capacity (6-5/8" nested) of a 12" miter saw
• Linear ball bearing system engineered to deliver "dead-on" accurate cuts
• Innovative direct drive gearbox and guard system is engineered for increased vertical cutting capacity (5-1/4")
• Unique 2-steel rail sliding system design offers single slide-glide operation; reducing saw's footprint and allowing operation flush against a wall
• Less weight (57.9 lbs.) and the most compact design in its Class for easy jobsite portability

User questions & answers

Question:	How close is the laser to the cut line? Does the laser line move as you lower the saw blade
Answer:	I'm not aware of any movement of the laser as you are lowering the saw down. Although the purpose of the laser is to be able to cut a mark line when the saw is in upright position.
Question:	Does this saw come with the extension wings like its pictured
Answer:	Yes they are included, they are attached to the saw. Loosen the thumb screw and slide them out.
Question:	As of Mar 2018, Does it still cut an arc when sliding, as opposed to a straight line
Answer:	Mine does not. Be careful with damaged packaging and saw impact
Question:	Does the laser show both sides of the blade, that is is it a dual laser? Also does the laser have a separate switch or is it centrifical
Answer:	The laser is on one line only and it can be switched left or right of the blade. There is a separate ON/OFF switch for the laser

Product features

Makita LS1019L 10" Dual-Bevel Sliding Compound Miter Saw with Laser

The Makita 10” Dual-Bevel Sliding Compound Miter Saw with Laser (model LS1019L) delivers large cutting capacity and accuracy right out of the box. With the LS1019L, you'll get all the cutting performance you need in a slide compound saw, but with the most compact size in the category for increased portability. With up to 6-5/8” capacity (crown molding, nested) jobs like cutting baseboards and crown molding are a snap, but with up to 5-1/4” baseboard, capacity, it can cut 4x4 dimensional lumber in one pass. It's ideal for fine woodworking, carpentry, general construction, and more.

The LS1019L is powered by a 15 AMP direct drive motor with soft start, a key point of difference. This means smoother start-ups and consistent, constant power with no belts to slip or replace. The electric brake provides added convenience. The LS1019L will tackle the most demanding jobs while keeping production high.

LS1019L Includes:

Vertical Vise (122854-6).

Dust Bag (122852-0).

Triangular Rule (762001-3).

10" x 5/8" 60T Micro-Polished Miter Saw Blade.

Hex Wrench 6 (781044-6).

Product description

The Makita 8-1/2" Slide Compound Miter Saw (model LS0815F) Has a compact and Lightweight Design for Job Site Portability. It combines these features with a powerful direct-drive motor. Portable and powerful, the LS0815F is an ideal cutting solution for applications ranging from woodworking and carpentry to room-to-room applications like finish, trim, and flooring installation. The LS0815F is powered by a direct drive 10.5 AMP motor with soft start. This is a key point of difference, as users will experience smoother start-ups and constant power with no belts to slip or replace. The electric brake provides added convenience.

• Compact and Lightweight Design for Job Site Portability
• Powerful 10.5 AMP direct drive motor requires less maintenance and delivers 5,000 RPM
• Miters 0-50 Degrees left & 0-60 Degrees right, with positive stops at 0, 15, 22.5, 31.6, 45 and 50 Degrees (left and right) plus 60 Degrees (right)
• Compact and lightweight (31.1 lbs.) for job site portability
• Cuts up to 12" at 90Degrees and 8-1/2" at 45Degrees

User questions & answers

Question:	Will a 8 inch blade fit
Answer:	Yes. You can, the saw will cut alot larger than a 2x6 laying flat.
Question:	Would it work on a electricity of 220 v
Answer:	Much quieter. Best saw I have ever owned!
Question:	Will this saw cut a 1×12 with one pass at a 45 deg angl
Answer:	Smooth. It slides twice on two sets of bars. I have used their 10" saw for years. I bought this for trim work but it will cut 2x all day. I haven't used the 10" since I bought this one. You will love it.
Question:	Does it come with the extension arms
Answer:	Yes you can. Use a 1/4” Masonite or plywood to bump out the fence to take care of the 1/4”. The smaller blade won’t cut all the way through if you don’t. Works fine for me. And yes it’s easier and cheaper to get the standard 7 1/4” blades than the special 7 1/2”s from Makita.

Product features

Lightweight for portability

The LS0815F weighs only 31.1 lbs. for increased portability. Additional features include a see-through blade guard system for greater visibility of the blade and line-of-cut. The ergonomic rubberized horizontal D-handle design has a better fit and added comfort, and the large trigger switch is designed for easier operation. The LS0815F also includes an L.E.D. light that illuminates the line-of-cut.

Great for general construction

The LS0815F is part of Makita’s expanding line-up of best-in-class miter saws that deliver capacity, accuracy, and portability for a range of cutting applications. It is ideal for baseboard and crown molding installation, finish carpentry, cabinet and furniture making, wood floor installation, deck building, general construction, and more.

Capacity

Cuts up to 12 inches at 90° and 8-1/2 inches at 45°

Versatality

Built-in L.E.D. light illuminates the line of cut for increased accuracy

Accuracy

Linear ball bearing system engineered to deliver "dead-on" accurate cuts

Portability

Compact and lightweight design (31.1 lbs.) for job site portability

Product description

The DWS716XPS 12 in. Double-bevel compound Miter saw is powered by a 15 amp motor that drives 3, 800 RPM to deliver extended power and durability. Integrated cutline™ LED work light system provides adjustment-free cut line indication for accuracy and visibility. This saw features a stainless steel Miter detent plate with 14 positive stops and cam Miter Lock system that provides repeatable accuracy and durability with easy adjustments. Tall sliding fences support 6-1/2 in. Of base molding vertically and 6-5/8 in. Of crown molding vertically nested.High efficiency dust duct is concentrated at the point of cut for maximum Collection. Lightweight design and built-in carry handle for portability. The new Dewalt DWS716XPS 12″ miter saw is almost identical to the DW716XPS, but there are some small changes. - Upgraded high visibility bevel scale - Longer base legs - New vertical quick clamp - Upgraded dust collection - Removable table under-guarding - New blade bolt design

• POWER AND DURABILITY: 15 amp, 3,800 rpm motor
• INTEGRATED XPS CUT LINE positioning system with LED light provides adjustment free cut line indication
• MITER DETENT PLATE IMPROVES PRODUCTIVITY AND ENSURES CUTTING ACCURACY: Adjustable stainless steel miter detent plate with 14 positive stops
• MITER DENTENT OVERRIDE that allows you to override the miter stops and adjust to the desired setting without the saw slipping into the miter detents
• EASIER BEVEL CUTS: Tall sliding fences support crown molding up to 6-5/8-inch nested and base molding up to 6-1/2-inch vertically against the fence while easily sliding out of the way for bevel cuts
• CROSS CUT CAPACITY up to 2x8-Inch dimensional lumber at 90° and a 2x6-Inch dimensional lumber at 45°
• DOUBLE BEVEL DESIGN: Double bevel design allows saw to bevel left and right 0 - 48 degree with positive stops at 0, 33.9, 45, and 48 degrees both left and right allowing user to flip the saw not the material

User questions & answers

Question:	Does anyone know a dewalt vacuum dust port adapter that would work with this dewalt dw716xps miter saw? thanks
Answer:	Adapters DWV9120, DWV9130 or DWV9150 are compatible.
Question:	Can you put a metal cutting blade on it to cut steel tubing
Answer:	Good question and I don't see any reason why not depending on the thickness of the tubing. I have a Dewalt chop saw I used to cut aluminum studs when I was refinishing my basement and it cut just fine with a metal cutting blade. It was a 10" vs 12" saw however. Motors and Amp rating was the same as my DW 716 Mite Saw. May want to ping someone at DeWalt or search thier web site. May not be the right thing to do but you could ask someone at one of the Big Box Home Improvement stores as well.
Question:	on dewalt's site it says this model is 3800rpm on here it says 3500rpm is this an older model
Answer:	On the saw that I bought 2 months ago, it says 3800 rpm on the motor casing.
Question:	Is the only difference between the DW716 and DW716 with XPS, the LED
Answer:	Dewalt 716 Type 20 will accept a light. You'll spend 75 on a handle, power supply, and led. MM Tool parts has the kit. The light is worth it.