2 best nail gun air compressor combo

A nail gun air compressor combo is a popular toolset used in construction and woodworking. It typically consists of a nail gun (specifically designed for various nail sizes and types) and an air compressor that provides the necessary pneumatic power to drive the nails into the material.This combo is commonly used for tasks like framing, trim work, and other carpentry projects.

Here are some key points about nail gun air compressor combos:

Types of Nail Guns: There are different types of nail guns, including brad nailers, finish nailers, framing nailers, and more. Each type is designed for specific tasks and nail sizes.
Brad Nailers: Brad nailers are designed for more delicate work, like attaching trim and molding. They use smaller, thinner nails called brads.
Nailers Staplers: Some combos may include a nailer stapler, which is capable of driving both nails and staples. This versatility can be useful for various tasks.
Power Tools: These combos fall under the category of power tools, which are tools that are driven by electricity, compressed air, or other sources of power, as opposed to manual tools.
Power Hand Tools: This term refers to any hand-held tool that is powered by electricity or a similar power source. Nail guns are considered power hand tools.
Tools Home Improvement: Nail gun air compressor combos are commonly found in the tools section of home improvement stores. They are essential for many DIY and professional projects.
Pneumatic Operation: The nail gun relies on compressed air provided by the air compressor to drive nails into the material. The air compressor pressurizes air and delivers it to the nail gun through a hose.
Regulation of Air Pressure: It's important to adjust the air pressure on the compressor to match the requirements of the specific nail and material being used. Too much pressure can damage the material, while too little may not drive the nail properly.
Safety Considerations: Like all power tools, it's crucial to follow safety precautions when using a nail gun air compressor combo. This includes wearing appropriate safety gear, keeping hands and fingers away from the nail discharge area, and using caution when handling the tools.

Remember, always follow manufacturer instructions and safety guidelines when using any power tools, including nail gun air compressor combos. This information should give you a good overview of what these tools are and how they are used in various construction and woodworking projects.

Below you can find our editor's choice of the best nail gun air compressor combo on the market

BOSTITCH Air Compressor Combo Kit, 3-Tool (BTFP3KIT)

Bostitch

Based on 2 reviews Check latest price

Product description

The Bostitch BTFP3KIT 3-Tool Portable Air Compressor Combo Kit is ideal for interior and exterior finishing and trimming project for a variety of crafts like furniture, cabinets, and staircases. It features a 150 max PSI 6.0 gallon tank (22.7 L) and 2.6 SCFM delivered 90 PSI pump, which enables long tool run time with quick recovery. The air compressor features long-life oil-free, maintenance-free pump for convenient use. It has a Bostitch high efficiency motor for easy start up in cold weather or extension cord application [14 ga or larger, 50 ft. (15.2 m) or less]. At only 78.5 dBA operational noise level it offers you a quiet work environment. The SB-1850BN 18 GA brad nailer drives 18GA brad nails from 5/8 in. to 2 in.. SB-1664FN 16 GA straight finish nailer drives 16 GA straight finish nails from 1-1/4 in. to 2-1/2 inch. The BTFP71875 heavy-duty 3/8 in. crown stapler drives 3/8 in. crown staples from 1/4 in. to 9/16 in. and 18GA brad nails from 1/2 in. to 5/8 in.. 1/4 in. x 15' PVC air hose with fittings is included. Includes: 1) 6-gallon Pancake Compressor, 1) 18GA 2 in. Brad nailer, 1) 2-1/2 in. 16GA Straight Finish Nailer, 1) Heavy Duty 3/8 in. Crown Stapler, 1) 25' Air Hose.

CORDLESS AIR COMPRESSOR: The BTFP02012 is at 6 gallons, 150PSI, and 2.6SCFM with a high efficiency motor.
BRAD NAILER: The SB-1850BN drives 18-gauge Brad Nails from 5/8" to 2" for a wide variety of applications
STRAIGHT FINISH NAILER: The SB-1664FN drives 1-1/4- to 2-1/2-inch, 16-gauge finish nails.
HEAVY DUTY CROWN STAPLER: The BTFP71875 drives heavy duty 3/8" Crown staples from 1/4" to 9/16"
AIR HOSE: 15-foot, 1/4" x 25' PVC air hose with fittings air hose, and fittings offer plenty of length for maneuverability
WARRANTY: This kit is covered by a 1-year limited warranty for peace of mind

User questions & answers

Question:	How long for pressure to build up on initial start up? Thanks
Answer:	If it's not holding pressure check all connections you may have a loose one.
Question:	If i buy this for my husband, do i need to buy an air hose, and if so, what do i buy? this is all stuff i know nothing about. thank you
Answer:	Air hose and some attachments come with. In the future you may want to get a kit with air gun, tire inflater and changeable fittings.
Question:	Can this be used for roofing
Answer:	It works perfectly to run one roofing gun. I’ve bought two of them and they both could handle the work load perfectly. And to comment on one of these guys replies to your question, He said the compressor would run continuously and burn up” well that’s not only untrue but impossible. You would have to be able to lay 5 square an hour all day long not just an hour or two for it to even be remotely possible to burn up that compressor. Not saying you couldn’t lay 5 square an hour but you can’t do it for several hours straight that’s for sure. I personally have put on 11 bundles per hour for the first 2 hours and the compressor did not run continuously and even if it did it wouldn’t have burnt up. Those specific compressors are designed to click off and on as many times as you can make them do so.
Question:	Can a framing nailer be used on this compressor or just finishing
Answer:	Yes, I run my Hitachi framing nailer off this. Maybe 30-40 .141 x3" nails into dimensional lumber before the compressor kicks on. Could I use a more powerful compressor for framing? Sure. But the weight and cost of this thing are very nice. Would be underpowered for roofing or sheathing applications, though.

3PLUS HCB050401 18-Gauge Brad Nailer and Quiet Air Compressor Combo kit

3PLUS

Based on 106 reviews Check latest price

Product description

The HCB050401 Finish Combo Kit from 3PLUS is ideal for a wide variety of finish and trim jobs. It comes with a HF50SP 18-Gauge Brad Nailer and a HC0504G Compressor. The brad nailer drives 18-gauge brad nails from 3/4'' to 2'', features an adjustable depth-of-drive, 360° air exhaust, quick-clear jam release and no-mar tip. The compressor has an oil-free pump that delivers 0.7SCFM@90PSI and 125 PSI max operating pressure. The oil-free pump requires NO lubrication and provides clean operation. The 1/2 HP induction motor offers you a quiet operation-65dBA noise, it also features overheat and overload protection.The Roll bar design protects vital components. The 1/4-inch quick coupler and regulator provides consistent, reliable operation, while individual gauges for tank and regulated output allow you to easily keep track of pressure. And to save your time, it takes only 130 seconds to pump up and 40 seconds to recover. This portable compressor only weighs 23lbs, so its easy to take from site to site as you work. Kit includes: HF50SP Brad Nailer, HC0504G compressor, air hose with fittings, goggle, wrenches and manuals.

18-gauge brad nailer(HF50SP) and 1-gallon compressor(HC0504G) combo kit is ideal for finish and trim jobs
HF50SP-Drives 18-gauge brad nails from 3/4'' to 2'', features an adjustable depth-of-drive, 360° air exhaust, quick-clear jam release and no-mar tip
HC0504G--Features a direct-drive, oil-free pump that ensures clean operation and minimal maintenance. Roll bar design protects vital components
Compressor Spec. are as follows: 1/2 HP, 0.7SCFM@90PSI, 1 gallon tank, 125 PSI max, low 65 dBA and 23lbs total weight.
Kit also includes air hose with fittings, goggle, wrenches and manuals

User questions & answers

Question:	Wanting to know if this nail gun works well and is easy to use
Answer:	I'm not really sure if this is what you are asking, if you mean, does it go on when they're pressure gets low, and then off when the correct pressure is reached, then the answer would be yes
Question:	what nails brand/type shall i buy
Answer:	Will not release unless pressed firmly against surface - part of safety feature - Also check to make sure cartridge is installed properly
Question:	Does the compressor have auto off auto on feature
Answer:	Mine doesn’t bend metal. Works great. Nice clean cuts
Question:	Nail gun newbie. attached and started compressor. loaded nails. pressed trigger, nothing. what am i missing? directions are less than helpful
Answer:	Hi, I am afraid this shear is not a good choice for 90° notches. It is not easy to control and probabaly with curling. I recommend the HN3-102 hand notches. Following video for your reference: https://www.youtube.com/watch?v=Kr1mFbwk_3s