9 best crown woodworking tools

Product description

This set consists of a pair of 2 1/2 inch by 5 inch cabinet scrapers made by Crown Hand Tools of Sheffield England. The Rectangular scrapers (2 1/2” x 5”) are the standard item for flat surfaces. Scrapers are .032 inches thick and are made of medium carbon steel with a hardness of 40/42 Rockwell C. This specification gives good edge retention while allowing the “spring” of “flex” in the blade which gives the user control of the tool. Cabinet scrapers are an invaluable aid to woodworking in putting a really fine finish on wood. They can also be used for removing traces of paint, varnish or distress marks on wood.

• This scraper set in made in Sheffield England by Crown Hand Tools
• Scrapers are 2 1/2" x 5" and are .032 inches thick
• Made of medium carbon steel with a hardness of 40/42 Rockwell C. This specification gives good edge retention while allowing the “spring” or “flex” in the blade which gives the user control of the tool
• This is a high quaity set that will last a lifetime
• Scraper edges are milled and not stamped which will speed sharpening

User questions & answers

Question:	Where is it made
Answer:	I have had mine for 4 years. There has been no rust develop on it.
Question:	Do you think these would be useful to smoother buttercream on cakes
Answer:	they are made in Portugal - Bahco apparently has a factory there
Question:	Do these come ready to use? Or do they need sharpened before use
Answer:	You will need to burnish the edges. They only stay sharp for about 10 minutes or so of use. Most people use an old router bit for this or you can buy a burnishing tool if desired. http://woodgears.ca/scraper/
Question:	Can I use these to shave off a few millimeters from a bowed wall stud
Answer:	Yes, the edges are machined.

Product description

Exceptional quality from Crown Hand Tools Ltd, Sheffield, England. Tempered High Carbon Steel Cabinet Scrapers (Rectangle, Gooseneck, Curved Shaped). Burnished can be used to return edge to cabinet scrapers. Kit includes; 2-1/2 in. x 5 in. Rectangle. Gooseneck and Curved Cabinet Scrapers (1 each). Burnished .

• Crown Hand Tools Ltd
• Burnished with hardened steel rod and genuine rosewood handle
• Cabinet scraper set with gooseneck, curved and rectangular
• Items are made in Sheffield England

User questions & answers

Question:

What is the thickness

Answer:

Hello,On EXR and Auto mode I've found my images in low light to be sub par without using the flash - which then can unfortunately cause it's own set of problems. However, as I learn the camera I find adjusting the settings and really depending on the manual as a reference guide, along with youtube tutorial videos that my low and dim light photos are improving. I'm an Amateur at this stage of course but more advanced photographers would have an effortless time taking great shots in low light conditions. If you're shopping around check out the Panasonic FZ200 and the Sony DDSC-HX300 both have won tremendous accolades for low light performance. Hope this helps!

Product description

Get a better bite on your spindle with PSI's new 1' Super Center. More teeth give a better bite while providing equal pressure and a positive drive. There is no need to hammer your drive center into the work piece and risk splitting your work. The PSI Super Center Crown compatible with headstocks with #2MT spindles. Spring loaded point simplifies spindle centering and retracts to avoid splitting your work when tailstock pressure is applied. Ships in plastic production sleeves at 4.8-ounces. 4.5" by 1.5" by 1.5" with a 1-inch crown.

• The PSI Super Center Crown compatible with headstocks with #2MT spindles
• Get a better bite on your spindle with more teeth for a strong grip while still providing equal pressure and a positive drive
• Spring loaded point simplifies spindle centering and retracts to avoid spitting your work when tailstock pressure is applied
• Ships in plastic production sleeves at 4.8-ounces
• 4.5-by-1.5-by-1.5-inches with 1-inch crown

User questions & answers

Question:	I have a 3/4' live male threaded end but lost the spur, I need to weld a spur to a bolt so need to know the diameter of the taper below the spur
Answer:	just as cheap to buy a new one. weld wont hold if you put any strain on it
Question:	I would like to know the dementions of the shaft that goes into the chuck I know its tapered but need to know big and small size thanks Jack
Answer:	If you have a Morse taper 2 (available in MT1) it has a taper of .04995 per inch. The approximate sizes of the big end and small ends are: 0.572 and 0.700. Those will vary depending on the depth of the socket (it's not a chuck), the length of the shank, and other variables. The only thing hard and fast about it is the taper.
Question:	I'm new to turning and would like to know if the "5/8 inch crown" is refering to the outside machined dimension at the bitting teeth end
Answer:	It is to the outside of the device, not from center to the points of the teeth. I don't recommend that you buy this, though. The center point is spring loaded and eventually the set screw on the side will come undone and fling off in a random direction. Then, when you take the piece off the lathe, the center point and spring will fly out the end. If you're lucky, you don't have huge piles of sawdust and you're able to find the pieces and put it back together.
Question:	My pin is also stuck. It was not from being dirty because I have never used it. Has anyone came up with a way to get the pin back out
Answer:	That's easy to fix. On the side, just below the teeth, you will find a screw. That screw allows you to do three things. First, it allows you to take the pin out if you don't want to use it. Second, it allows you to lock the pin so it does not retract. And last, probably what you are interested in, it allows you to free up the pin so it slides up and down. When the pin is out you will notice a notch on one side. Make sure the screw and notch are lined up or the pin just might shoot out at you the next time you loosen it. Do for now just loosen the screw about a quarter turn and the pin should loosen up. If it doesn't then take the pin out and see if something got into the spring which is behind it. Hope this helps.

Product description

The New AccuMASTER 7” Digital Protractor Rulers gives you the right angle on ALL your projects! This versatile precision tool is indispensable for woodworking, crown and baseboard moldings, door and window trim and other general carpentry tasks including welding and fabrication projects. SAVES TIME, REDUCES COSTLY MATERIAL WASTE – give yourself the ability to quickly and accurately measure both inside and outside angles and you will not only save time and frustration but will also eliminate material waste due to inaccurate angle measurements and/or guesstimating. MOST REQUESTED FEATURES – ideal 7” size is long enough to get a good sample of the measured surface without being too long or unwieldy. Durable stainless steel rulers are clean and uncluttered for easy reading and permanently etched with your favorite measuring scales for long lasting use and enjoyment. The AccuMASTER has both an auto-Off and manual Off function to preserve battery life and dependability. SPECIFICATIONS – Angular range: 360° in both inside and outside directions Accuracy: +/- 0. 3° Display resolution: 0. 1° Displayable measuring range: 0°~999. 9° Ruler measuring range: 7 inches (180 mm) Working temperature: 32-122°F (0~50℃) Auto-off: 5-7 minutes inactivity Power Supply: CR2032 3V lithium battery life: 1000 hours (2+ years for typical/most users)   YOU’RE PROTECTED! – included carry pouch fits easily in tool drawer or apron. Note some scratching of the blades is normal due to the tight tolerance as the blades pass over one another. You’re also protected against frustration by our User Guide that plainly and legibly spells out operations and everything you want to know about your new tool. Lastly, your purchase is protected by our 2-year limited . Click Add to Cart to get the new AccuMASTER Digital Angle Finder Ruler today! Copyright 2019 Calculated Industries All Rights Reserved

• VERSATILE ANGLE MEASUREMENT TOOL doubles as both a digital angle gauge and a protractor for measuring all your workshop angles, bevels, miters for crown, trim, molding, baseboard, squaring frames, general woodworking, setting miter saw blade angles and more.
• MEASURE 360 DEGREES – pivot allows full rotation in both directions so you can precisely measure inside or outside angles With ease at +/- 0. 3 degree accuracy. Large LCD display Digits make it easy to read.
• INSTANTLY RESET YOUR ZERO POINT at any position for relative angles. To find relative angle, determine first angle then push the zero button, then measure second angle to see the difference. LCD display Hold lets you freeze a displayed value before moving tool.
• EASY TO READ stainless steel rulers have permanently etched markings in 16ths and mm's on one and 32nds and mm's on the other for easier, clearer reading of precision measurements in your favorite units and scale.
• COMES COMPLETE – with protective case, long-life CR2032 3V battery, Manual and Auto-off, clear American-written, large-print user guide and 2-year limited warranty

User questions & answers

Question:	does the LCD display flips when you turn the tool from right to left and up and down
Answer:	No it does not flip. Sorry.
Question:	Are the two metal rulers supposed to be the exact same width? Not to be confused with thickness. There is a .28 mm difference between the two blades
Answer:	Symmetrical with both sides for accuracy

Product features

Measure inside and outside angles

Measure the full range of both inside and outside angles within a 10th of a degree. Plus you can measure degree changes by manually “zeroing” the gauge on one angle then measuring the relative angle between two surfaces.

Protective storage pouch

The Angle Finder comes with a rugged storage pouch to protect the gauge when it is not in use. The storage pouch keeps the angle finder safe and scratch free while in your tool box or work belt.

Ready to use

The Angle Finder comes with a protective pouch and one CR2032 battery along with a detailed user guide so you can start using the angle finder right out of the box.

Product description

Crown Tools 106 / Big Horn 22206 fine quality 20-oz 4-1/2-Inch Beechwood Woodcarvers Mallet is manufactured from the finest kiln dried beech.

From the Manufacturer

This fine quality Crown 20-Oz 4-1/2-Inch Beechwood Woodcarvers Mallet is manufactured from the finest kiln dried beech.

• Exceptional quality tool from Crown Hand Tools Ltd, Sheffield, England
• Weight: 20 oz
• Head Diameter: 4-1/2"
• Manufactured from Finest Kiln Dried Beech
• Application: Designed to be quiet and yet transmit the maximum blow

User questions & answers

Question:	does the handle weigh the same as the head
Answer:	There's a door on the end. It's on the right end as you face the camera screen. But I didn't know you can charge the battery room USB. I'm going to double check that.
Question:	Where is it made
Answer:	That's not a question! It takes standard SDMC cards (not the micro ones). The one that came with mine is 4 GB, which is plenty big enough.
Question:	How many ounces
Answer:	Hello Fremen. I have 2 Fuji cameras bought from Amazon and none came with a Warranty Card inside the box. There is a flyer inside that gives you instructions on how to Register the Model and Serial number of you camera with Fuji-USA in order to Activate your Warranty. You need to keep your Original Invoice from Amazon or Sales slip from the Vendor you got your Camera from. That is all you have to do to get the Warranty going in the USA. One year from the time of sale. Enjoy your new Camera.Aaron...
Question:	What is the dimension of the mallet? (head size, length, etc
Answer:	I scored the deal yesterday and have it in hand today. Serial Number 33.......... This tells me that it was produced in 2013, 3rd quarter so it definitely is the new sensor. It doesn't exibit lens droop or unwind. There is a little play in the lens when extended, but not like I saw on Utube videos of the problem. Battery is charging and I'm fired up!

Product description

Whether you are applying moldings and trim or whipping up a run of picture frames one of the biggest hassles in gluing up mitered corners is keeping them from opening up.Spring clamps are the quickest and easiest way to do it and the Collins Spring Clamp System is one of the most economical we've ever come across.The clamps spread up to approximately 2, so they will cover most trim sizes and any compound miter. The clamps can be applied and removed by hand, but the Spring Pliers make the job much easier.They will really save your hands, plus the Pliers place clamps exactly where you want them, and help keep you from scratching stock when you remove them.  Includes pliers and 4 miter clamps. 

• Pliers and 4 spring miter clamps included
• Miter clamps spread from 0 to approximately 2 inches. No need to carry a bunch of different sizes
• Sharp point pierces the wood without cutting wood fibers vs the competitions angled cut
• Keeps any mitered corner from opening up while glue dries for the perfect finish
• Great for picture frames, moldings, trim work and any compound miter

User questions & answers

Question:	can you just squeze them with your hand
Answer:	Barbara you can find the DIGITAL CAMERA SERIES FINEPIX S1 MANUAL in Google. And you can print it in different Languages.
Question:	What material are the spring clamps made of, steel, titanium, aluminum
Answer:	I have had an Fujifilm HS-20 EXR bridge camera for a few years with a plastic thread for the tripod mount and no problem as long as one is careful not to cross thread it. So when I purchased the S1 I was not overly concerned with the plastic thread mount. That said, I don't use the tripod mount much. Just be aware its plastic and don't cross thread or use a tool to over tighten where to where the threads would be stripped. I've used a coin to tighten the camera with no problem with camera movement ro thread issues.
Question:	Do they leave any mark or depression in the wood
Answer:	The Finepix S1 is not, for some unknown reason, threaded for filters. The camera requires the use of an adapter to mount filters. With the adapter you can use 72mm filters. The ASIN for the adapter which is fairly expensive is: B00HVXW12E
Question:	Are they made in America
Answer:	This camera utilizes SD, SDHC, SDXC memory cards up to 128GB according to the Fujifilm memory card compatibility web page.

Product description

This Crown 9” Pioneer Range Try Square combines the beauty and reliability of sustainable, imported stabilized bamboo and solid brass. Square has blued steel blades triple pinned to its handle. A 1/8"-thick brass rub plate protects inside face for accurate readings. This square is manufactured to British Standard BS3322 and is one of the many accurate, attractive traditional Sheffield product offerings.

• 9" length
• 1/8” Brass rub plate
• Stabilized Bamboo, solid brass
• Combines beauty and reliability
• Blued steel blades triple pinned to handle

Product description

Remember when you had a reliable stapler? Fasten thin materials tightly and securely with the WEN 20-Gauge Pneumatic Stapler. Shoot 3/8-inch crown staples (T50) ranging from 1/4 to 9/16 inches in length. Simply attach the compressor of your choice to the 1/4-inch NPT air inlet, and get to stapling. With a rubber-gripped handle and a lightweight aluminum body, you’ll have maximum comfort during long days on the job site. The spacious magazine holds up to 100 nails while the magazine’s side window helps you know when your staple supply is running low. The 360-degree adjustable exhaust rotates any direction to direct the air output away from the user. The WEN Stapler operates at 70 to 100 PSI, using 0.28 SCFM of air at 90 PSI. The compact design is perfect for stapling wood and upholstery in even the tightest corners. And because it’s a WEN product, your stapler comes backed by a two-year warranty and a friendly customer phone line. Remember when you could finish the job without a jam? Remember WEN.

• Perfect for upholstery, woodworking, trim work, vinyl installation and more
• Shoot 3/8-inch crown staples ranging from 1/4 to 9/16 inches in length
• Features an adjustable 360-degree air exhaust and a 1/4 inch NPT air inlet fitting
• Compact 1.8-pound design features an extended nose for tight areas and corners
• Spacious magazine holds up to 100 fasteners at a time

User questions & answers

Question:	Will this tool accept 18 gauge staples without harm? I bought this because it said T50 staples, but they seen to be 18 gauge
Answer:	I got KeLDE 5000 piece staple kit from Amazon. They worked, but came loose in the bag, which seemed strange. I hope this helps.
Question:	depth adjustment how to
Answer:	Not sure what you mean
Question:	What brand of staples would this gun need
Answer:	Yes. There’s socket for slow and fast.
Question:	Are there any reviews for the wen 61705 20-gauge t50 product which is actually listed on the page
Answer:	No, it doesn't have any cartridges inside. It doesn't have filter also

• 📢Friendly customer service: we provide new replacement instead of repairing.
• FOR FREE---Tools includes 200 staples and 800 brad nails.
• 🔰CONVENIENCE --The wire 2-in-1 brad gun/staple gun doesn't need compressors, hoses for convenience use.
• 🔰WIDE APPLICATION -- The upholstery nail gun ideal for softwood DIY projects such as Carpentry DIY, picture framing, door or window molding installation, pet house DIY while not recommended for quarter round, baseboard, drywall installation, roofing and flooring.
• 🔰FLAWLESS FINISH -- Non-Marring rubber nose provides a complete finish.
• 🔰FRIENDLY USE -- The wire 2-in-1 brad gun/staple gun equipped with ergonomic soft-grip handle for reducing worker fatigue.
• 🔰ADJUSTABLE POWER -- This electric brad nailer designed with adjustable power function for light-duty project.

User questions & answers

Question:	Mine will fire but it wont shoot any nails and i have not even used it for a day
Answer:	I could get mine to shoot, but it wouldn't go into soft trim more than 1/8 inch. That was maximum depth... Most were less than half that. I sent it back.
Question:	Repairing rattan rawhide bindings. Will this shoot 23 GA, 3/16" crown, 3/8" leg
Answer:	Hello Customer, No, this electric Brad Nailer/Stapler drives 18 GA brad nails up to 1-1/4'' inch and 1/4'' crown staples up to 1". Using improper nails/staples may cause operational problems. Hope this can help you. If there is anything issue we can help you, please do not hesitate to contact us via [[email protected]] and we will reply to you ASAP. Spartatool Support Team
Question:	podrias especificar con que grapas es compatible y donde se puede adquirir las grapas
Answer:	Puedes conseguir las en Walmart o cualquier ferretería. A mi me a sido muy útil.
Question:	Electric brad nailer, neu master ntc0040 electric - does this model drive 1”, 1 1/2” and 2” brads
Answer:	Hello Customer, The longest brad nails can be used for this electric brad nailer/stapler is 1-1/4''. And this length is recommend for soft wood. Hope it can help you. If you have any issue or need help during use, please do not hesitate to contact us via [[email protected]] and we will do our best to serve you. Spartatool Support Team

Product features

Product Overview

The NEU MASTER NTC0040 Electric Brad Nailer/Stapler drives 18 gauge brad nails up to 1-1/4'' inch and 1/4'' crown staples up to 1" which makes it ideal for general repairs, craftwork, interior or exterior decorative lightweight trim, upholstery, and more. No compressor needed and the nail gun features a quick-release mechanism and an overmolded grip for convenient use. Kit includes a Brad Nailer Stapler, 400pcs 5/8'' brad nails, 400pcs 3/4'' brad nails and 200pcs 3/4'' staples.

• Drives nails and staples
• Ergonomic grip for comfort and control
• Power adjustment dial and oversize trigger
• Quick-release mechanism
• Contact safety with non-marring nose provides a flawless finish