14 best fly cutter for milling machine r3

Product description

Remember when you could cut through metal? Glide through 20 gauge stainless steel or 18 gauge sheet metal with the WEN Variable Speed Electric Metal Shear. The lightweight 4.7-pound design limits fatigue during operation while the powerful 4-amp motor makes easy work out of a variety of metals. The pressure sensitive switch adjusts the speeds of the cut anywhere from 0 to 2500 strokes per minute depending on the force applied. The pivoting head rotates a full 360 degrees to allow for cutting at any angle or direction without having to have an awkward or uncomfortable hold on the shear’s handle. And, because it’s a WEN Product, your purchase comes backed by a two-year warranty, a nationwide network of skilled service technicians and a friendly customer phone line all to make sure you remember WEN.

• Pressure sensitive trigger cuts anywhere from 0 to 2500 strokes per minute
• Attack up to 20 gauge stainless steel and 18 gauge sheet metal
• Lightweight design limits fatigue during operation
• Utilizes a powerful 4-amp motor, curling the metal as it cuts
• Swiveling head rotates a full 360 degrees to meet the needs of any project

User questions & answers

Question:	Will it cut the plastic on a truck truck bedliner
Answer:	I found it cuts vinyl soffit with no trouble, neat, efficient and quick. I think they are similar.
Question:	will this cut the alum side panels on enclosed trailer
Answer:	Easily, I've used it on 1/8th thick T6 alum without any issues.
Question:	Does it come with a case
Answer:	Mine did not come with a case.
Question:	How well will this cut 29 gauge galvalume rib steel roof panel? i see the spec for 18 gauge metal
Answer:	I cut 28 gauge steel with it with no problem 29 gauge is thiner yet ( smaller the # thicker the steel ).

Product features

Shear Metal. Sheer Power.

Remember when you could cut through metal? Glide through 20 gauge stainless steel or 18 gauge sheet metal with the WEN Variable Speed Electric Metal Shear. The lightweight 4.7-pound design limits fatigue during operation while the powerful 4-amp motor makes easy work out of a variety of metals. The pressure sensitive switch adjusts the speeds of the cut anywhere from 0 to 2500 strokes per minute depending on the force applied. The pivoting head rotates a full 360 degrees to allow for cutting at any angle or direction without having to have an awkward or uncomfortable hold on the shear’s handle. And, because it’s a WEN Product, your purchase comes backed by a two-year warranty, a nationwide network of skilled service technicians and a friendly customer phone line all to make sure you remember WEN.

360-Degree Swivel Head

Pivot the head 360° to help accommodate comfortable cuts from any angle or direction.

Cut up to 18-Gauge Metal

The powerful 4-amp motor slices through 18-gauge sheet metal and 20-gauge stainless steel.

Variable Speed Operation

The pressure-sensitive trigger varies the strokes per minute from 0 to 2500 SPM depending on the pressure applied.

Double Cut Design

The double-cut blade configuration creates a 1/4-inch ribbon of curled metal during operation.

Lightweight Design

The lightweight ergonomic design weighs in at a mere 4.7 pounds, limiting fatigue during operation.

3-Inch Turning Radius

Cut circles with radiuses of 3 inches and up to help take on projects with a lot of turns and curves.

Product description

The table is suitable for Mini Drill and drill bracket series.

It can also apply to other suitable machine.

The work table is composed of several adjustable dovetail slot aluminum alloy composition, can guarantee the minimum space and ensure the accuracy

Table size: 365 × 200 mm. Weight: 6.8 kg

X axis distance is 350 mm. Y axis distance is 100 mm.

Hand Wheel Scale Per Ring is 3 mm.



Package includes:

1 Pc of Milling table of Heavy Version

• The table is suitable for Mini Drill and drill bracket series. It can also apply to other suitable machine.
• It can also apply to other suitable machine. The work table is composed of several adjustable dovetail slot aluminum alloy composition, can guarantee the minimum space and ensure the accuracy.
• Table size: 365 × 200 mm. Weight: 6.8 kg
• X axis distance is 350 mm. Y axis distance is 100 mm. Hand Wheel Scale Per Ring is 3 mm.

User questions & answers

Question:	What is the actual X-axis travel distance for the heavy version
Answer:	3.0625" overall height (3 1/16")
Question:	Why does the medium model have more X &Y travel than the large model
Answer:	metal
Question:	What is the length and width of the cast iron base
Answer:	Thank you raising your concerns. The 2.5" milling vise is not included. You will need to purchase another 2.5" milling vise. What You Get: Milling Working Cross Table *1; Accessories box *1(hexagon wrench *1, standard fixture *1, M8 bolts and nuts *2); Manual *1. Any question, please don’t hesitate to let me know. Thank you for your attention to this product.
Question:	As this unit sits on a bench. What is the approximate height from the bench to the top of the table? Thanks
Answer:	I bought my clamps at harbor freight and Grainger supply

Product description

The Rockwell BladeRunner X2 Portable Tabletop Saw is the solution to the problem of having to take materials back to the workshop to cut them, and then bring them back to the job site later on. If you’re a contractor, you know that that process can add an entire day to a project. The BladeRunner is only 15 lbs, so while stable and sturdy, it’s easy to toss in the back of the truck. And with a footprint of only 15.75” x 17”, it doesn’t take up an entire workbench like traditional table saws. The hold-down guard and splitter allow for work with wider materials, and a larger rip fence than other portable table saws provides better control and accurate cuts. A no-load speed of 3000/min, a stroke length of ¾”, with 5.5 amps of power gives it the capacity for light to moderate cutting of wood (up to 1-1/2”), ceramic tile (3/8”), PVC pipe (1-1/4”), aluminum (3/8”), and steel (1/8”). (Anything over 1-1/2” and you’re probably going to need a traditional, permanently fixed tabletop saw—but you can’t take that to the job site.) The blades change out almost instantly, in under 3 seconds once you get the hang of the tool-less blade change system. And the saw is protected by a Rockwell 3-year limited warranty, so you know they stand behind their tools.

• [SETS UP IN SECONDS] Take this table saw to the job site or move it around the workshop. There’s even a built-in carry handle
• [CUTS LIKE A FULL-SIZE] With the standard guard and riving knife system you can perform rip, cross, scroll, and miter cuts
• [TOOL-LESS BLADE CHANGE] Uses any brand’s standard 4” T-shank blade, but we threw 5 in the box to get you started cutting wood, ceramic tile, plastic, aluminum, and metal
• [0-60° MITER CUTS] With the adjustable gauge you can pull off precise miter cuts for a whole assortment of woodworking projects
• [ON-BOARD ACCESSORY STORAGE] When the miter gauge, rip fence, and extra blades aren’t in use they can be conveniently housed in the base of the saw
• [SAFETY SWITCH] Prevents accidental starting, plus the vacuum port lets you hook up a shop vac that cleans while you cut

User questions & answers

Question:	What is the difference between this unit and the RK7321 BladeRunner
Answer:	It is a 30mm arbor. You have to get metric sizes in blades.
Question:	how would it work w/ making pinewood derby cars
Answer:	the tacklife saw blade has that size arbor ans 120 teeth
Question:	Can it hold up to regular use with 1" hardwood like maple and ash? If not, what will
Answer:	Yes, it can be replaced.
Question:	Is the table made from plastic? It is hard to tell if it is made from black plastic or anodized aluminum
Answer:	No it is not.

Product features

Adjustable Miter Gauge

Make cuts from 0-60° so you can tackle all common woodworking projects that require miter cuts.

Accessory Storage in the Base

For easy transport and organization, just pop the rip fence, miter gauge, and extra blades into the bottom when not in use.

Portable and Powerful

A table saw that you can take with you to the job or easily move around the workshop. Convenient carry handle makes it easy.

Capability of Larger Table Saws

Rip, cross, scroll, and miter cuts are all possible thanks to the standard guard and riving knife system.

5 Blades Included

Wood, ceramic, plastic, aluminum, and metal. Plus, the tool-less blade change system accepts any brand’s standard 4” T-shank blades.

Weighs Only 15 Lbs. for Easy Transport

Throw it in the back of the truck and take it to the job site. That’s not something you can do with a traditional, permanently installed table saw. Saves time when you don’t have to bring materials back and forth between the workshop and worksite.

Make Miter Cuts 0-60° for a Wide Range of Projects

Even though it’s compact, this saw features a standard guard and riving knife system to give you the flexibility and performance of larger table saws. And 5 blades are included to get your started right out of the box.

Product description

The Genesis GES40 swivel head electric metal sheer tool cuts through various metals with ease with a 4.0 amp motor.

- 4.0 Amp Motor

-360° Swivel Head for cutting curves in sheet metal

-Quickly cuts metal roofing, flashing, and other sheet metal up to 14 gauge

-Three blades work to reduce metal deformation

-Cut 14 Gauge aluminum, 20 gauge stainless steel, or 18 gauge Steel

Genesis' two year warranty means you buy with confidence. Cord Length- 72 inches.

• Quickly cuts metal roofing, flashing, and other sheet metal up to 14 gauge | Compare the Genesis metal shear to other drill attachment Shears that can only cut 20 gauge Sheet metal!
• Powerful 4.0 amp motor
• 360° swiveling head for cutting control and convenience |cut circles and curves with the Genesis electric metal shear
• Variable speed (0-2500) SPM for versatility in cutting a variety of materials | cuts through sheet metal up to 14 gauge in thickness!
• Three blade cutting system reduces metal deformation | experience smooth cuts EVERYTIME!

User questions & answers

Question:	i need to cut felt padding for carpets. Will this do the job without fraying the cloth
Answer:	No, capacity for mild steel is 14 GA.
Question:	Will tjis cut plastic
Answer:	DCS494M2 includes (2) 4 Amp hour batteries and (1) charger.
Question:	Will it cut dimensional asphalt roof shingles
Answer:	Dewalt makes an adapter (Dewalt DCA1820) that allows you to plug their newer 20V batteries into the older style 18V tools; (but you will need the adapter and a 20V battery starter kit (like Dewalt DCB205-2CK) so you can charge the batteries) by James Perdue HVAC contractor
Question:	Does this machine use 220V? Thanks
Answer:	"I think if you would cut with a 1/2" grinder all the way around, then use this tool to trim off the burrs, you would have a nice cut. I use this to make cuts for metal roof installations. I've not used it in steel duct. It is an excellent tool." (I am quoting my construction contractor husband.)

Product features

Genesis GES40 4.0 Amp Corded Swivel Head Variable Speed Electric Power Metal Shear

Features:

• Quickly Cuts Metal Roofing, Flashing, and other Sheet Metal up to 14 Gauge
• Powerful 4.0 Amp Motor
• 360° Swiveling Head for Cutting Control and Convenience
• Variable Speed (0-2500) SPM for Versatility in Cutting a Variety of Materials
• Three-Blade Cutting System Reduces Metal Deformation
• Cutting Radius of 5-1/2″ and Larger
• Lock-On Switch for Extended Use
• Built-in Belt Clip
• Includes: Hex-Key for Easy Blade Replacement

Product description

Designed for professional use, the Heavy Duty Circle Cutter will make clean cuts from 1-3/4 to 7-7/8 inch diameter. The tempered steel body features marked graduations on the beam for fast measurement and application. #55 Heavy Duty Circle cutter is designed with a 1/2 shank for drill press use only; Maximum safe speed is 500 RPM. This round shank circle cutter is great for making smooth cuts through most materials, including wood, composite, sheet metal and more; Shank is 1/2 inch round. All adjusments are made with a hex wrench which is included; Replacement blade is General Tools Model # 55 Blade, replacement drill is General Tools Model # 5/6/55 Drill.

GENERAL TOOLS - THE PRECISE TOOL FOR DOING THE JOB EXACTLY RIGHT. Offering over 1,000 tools, we’re proud to provide tradesmen, craftsmen and DIYers around the world with a broad range of affordable, specific-purpose mechanical hand tools and precision measuring and inspection tools.

For inquiries, please contact our Customer Service Department at 212-431-6100. We strive to provide our customers with 100% satisfaction.

WORK SMARTER, MEASURE BETTER & BE MORE PRODUCTIVE WITH GENERAL TOOLS

From the Manufacturer

Works like an adjustable hole saw. This heavy-duty circle cutter most preferred by professionals. 1/2 round shank for drill press use. Replaceable 1/4" high-speed tool steel bit and replaceable 1/4" pilot drill. Capacity 1-3/4" to 7-7/8".

• Designed for professional use, the Heavy Duty Circle Cutter will make clean cuts from 1-3/4 to 7-7/8 inch diameter
• The tempered steel body features marked graduations on the beam for fast measurement and application
• #55 Heavy Duty Circle cutter is designed with a 1/2 shank for drill press use only; Maximum safe speed is 500 RPM
• This round shank circle cutter is great for making smooth cuts through most materials, including wood, composite, sheet metal and more; Shank is 1/2 inch round
• All adjusments are made with a hex wrench which is included; Replacement blade is General Tools Model # 55 Blade, replacement drill is General Tools Model # 5/6/55 Drill

User questions & answers

Question:	Where is this product made
Answer:	The company is out if New York and has been around since 1920's
Question:	can I cut a 120mm hole in acrylic glass of my computer case
Answer:	I have successfully cut both 1/4" and 1/8" thick acrylic with this cutter. Your drill press should be set to it's lowest speed, and the cutter advanced into the work as slowly as possible. If you have the material available, sandwich the acrylic between a piece if 1/4" plywood, mdf or similar materiel on top with a thicker backer board of the same or similar material on the bottom. Clamp the sandwich assembly to the drill press table. The sandwich will help flatten the acrylic if it is warped, and lessen the possibility edge fracture from the cutter. Progressively finer grits of sandpaper may be used to dress up the edges of the cut.
Question:	Can it be used on light gage steel
Answer:	Yes...if you are careful to keep the material flat on a backer board. And remember this cutter is to be used only on a drill press. I have used these cutters to cut instrument holes in .090 aluminium.
Question:	can this be uaed with a hand drill
Answer:	NOT MADE FOR USE WITH A HAND DRILL

Product features

Heavy-duty Circle Cutter

The #55 Heavy-duty Circle Cutter can produce precise circles in sheet metal, brass, copper, soft steel, aluminum, plastic, wood and composition materials.

• Durable body of heat-treated tool steel
• Adjustable to various diameters by included hex wrench
• Only safe to use with drill press running at less than 500 rpm
• Included blade (#55 Blade) and 1/4 in. pilot drill bit (#5/6/55 Drill) are replaceable

• Carbide Indexable End mills, R8 shank, 2'' TPG32
• Comes with inserts installed
• Uses standard triangular inserts
• Positive rake 90° right-hand cut
• R8 Bridgeport thread: 7/16" - 20

User questions & answers

Question:	Can this be used to cut hard woods witthout burning the wood
Answer:	As others have have stated it really depends on a lot of things, this is however more of a face mill it's not intended to take deep fast cuts, if you need to go deep use a conventional roughing end mill and use this for your final passes to get a nice clean finish. I've used mine on titanium and 7075 aluminum and it has produced a very nice smooth finish on the material.
Question:	How many thousandths cut (per pass) can one take when using this tool on various metals
Answer:	Look up ‘speeds and feeds’. Google that phrase, you’ll find what you need. Varies greatly with what you’re cutting, depth of cut, lubrication, rigidity of machine and workholding.
Question:	What rpms have people been running this at? i have found suggestions on pm ranging from 250, to 2200... makes no sense
Answer:	This is Standard R8 Shank ( Bridgeport Shank); which means the smaller end is 0.949" and larger end if is 1.25"; Shank length is 4"; drawbar thread is 7/16-20. Thanks.
Question:	What is the shank diameter
Answer:	My first answer is 7/16 in. I have a set of Irwin tap chucks that grab the square shank .. another brand of tap has a 3/8 inch .. perhaps a small crescent wrench

Product features

AccusizeTools Carbide Indexable End Mill, R8 Shank, with TPG Inserts

• Carbide Indexable End Mills
• R8 Shank
• Carbide Inserts: TPG
• Comes with inserts installed
• Uses standard triangular inserts
• Positive rake 90° right-hand cut
• R8 Shank Threading: 7/16" - 20

SKU: 0046-0915

• Cutting Diameter: 1"
• No. of Inserts: 2
• Insert: TPG22
• Locking Screw: SM5 x 10

SKU: 0046-0916

• Cutting Diameter: 2"
• No. of Inserts: 3
• Insert: TPG32(TPGN1603)
• Locking Screw: SM6 x 12

SKU: 0046-0917

• Cutting Diameter: 3"
• No. of Inserts: 5
• Insert: TPG32(TPGN1603)
• Locking Screw: SM6 x 12

Cutting Speed for Low-carbon Steel, High-carbon Steel, Alloy Steel, and Tool Steel

• Carbide Indexable End mills, 3/4'' straight shank, 2''
• Comes with inserts installed
• Uses standard triangular inserts
• Positive rake 90Degree, right hand cut. TPG32
• 3/4'' straight shank

User questions & answers

Question:	where can i get just the button head screws for this tool
Answer:	I would just Google it, the screw is an M6 x .75mm x 10mm Button head cap screw
Question:	i'm a newbie so this is used strictly to face off a work piece.?? that's what i need it for
Answer:	It pretty much is for facing.
Question:	where can i get the insert hold down screws
Answer:	Look on McMaster carr
Question:	Is delivery fast
Answer:	If you are from the USA and if you have the prime membership, the delivery would be very fast because Amazon takes care of the shipping for prime members. Their delivery efficiency is very competitive.

Product features

Accusize Straight Shank Carbide Indexable End Mill

The 3/4" straight shank indexable end mills are for general machining work. The triangle carbide TPG inserts help you save time and money. When a cutting edge becomes dull, you just need to rotate the insert in the holder to use the sharp edge. When you buy the replacement inserts, be noted that the larger nose angles and larger tip radii enable a stronger cutting edge, but they result in increased vibration and a rougher finish. Beyond, be noted that the listing has our recommended cutting speed of the indexable shell milling cutters with straight shanks.

• Comes with TPG inserts installed
• Uses standard triangular inserts.
• Positive rake 90°, right-hand cut.

**Please note that we keep upgrading the products without further notification. Sometimes you will receive the products with Tin coated carbide turning milling TPG inserts. The coated inserts last longer and can run at faster speeds than uncoated ones.

-----------------------------------------------------------------------------------------------------------------------------------------------------------------

Specifications and Diagram

-----------------------------------------------------------------------------------------------------------------------------------------------------------------

Recommend Cutting Speed

• V= Cutting Speed (m/min)
• f= Feed per tooth (mm/Z)
• ae=Cutting width(mm)

For Reference Only

Product description

Each Fly Cutter is supplied with black oxide finish, a setscrew flat and a blank high speed steel tool. 1/2-Inch shanks. 3/4-Inch, 1-1/8-Inch and 1-3/8-Inch head sizes. 3/16-Inch, 1/4-Inch and 5/16-Inch bit sizes. Stand Included.

• Head Sizes: 3/4-Inch, 1-1/8-Inch and 1-3/8-Inch
• 1/2-Inch Shank
• Bit sizes: 3/16-Inch, 1/4-Inch and 5/16-Inch
• Black oxide finish
• Set screws and blank hss tools included

User questions & answers

Question:	Can they bore cast iron
Answer:	Determine the diameter and depth of cut, then do a search on the web, there are many good feed and speed charts available
Question:	what would be a good RPM to run at for aluminium
Answer:	I have used these fly cutter in my mill up to 1500 rpm. Good cutting around 900 rpm for aluminum. slower for steel.
Question:	What is the maximum RPM for these cutters
Answer:	With the stock bit it's about 70mm on the large cutter. But with a larger bit I'm cutting 120mm (5") on wood. Would not recommend very large diameters for metal.
Question:	whats largest diameter cut of this set
Answer:	no I.D. on the edge finder. case has mitutoyo america sticker on it. works fine no problem with it.

Product description

Features:

End Trimmer For Edge Banding; Double blades

Widely used for furniture, cabinet making, decoration and other industries

An indispensable tool for woodworking 

The repairable edge thickness must within 0.5mm, width within 40mm

Fits for various material, such as flexible melamine paper, wood, plastic, PVC, etc.

 

Specifications:

Material: Plastic

Blade Material: High-carbon steel

Color: Blue

Size: 13.8CM (L)*8.6CM (W)*8.5CM (H)

 

 

Package included:

1X Woodworking Edge trimmer

1X Spared Blade Set

• End Trimmer For Edge Banding; Double blades
• Widely used for furniture, cabinet making, decoration and other industries
• An indispensable tool for woodworking
• The repairable edge thickness must within 0.5mm, width within 40mm,Fits for various material, such as flexible melamine paper, wood, plastic, PVC, etc.
• Fits for various material, such as flexible melamine paper, wood, plastic, PVC, etc.

User questions & answers

Question:	can you get replacement blades for this cutter
Answer:	Not sure of material but I can say they do not last very long.
Question:	Will this cut 45 degree angles
Answer:	My set only came with brake pads.
Question:	How to use
Answer:	Not really.. you are going to need a bigger brake caliper then this particular style has the offer..these brake pads are maxed out on a 50cc or less motorized bicycle.. you will need more braking power then this for 212cc
Question:	Does this both trim the edge and cut the tail end
Answer:	From cross reference I have seen these pads will fit.

Product description

uses inexpensive standard tool bits

Makes wider cuts than end mills

Faster speeds and better finishes

Less chatter and free-cutting on thin material or non-rigid set ups

• Part# 202-5157
• Uses inexpensive standard tool bits
• Makes wider cuts than end mills
• Faster speeds and better finishes
• Less chatter and free-cutting on thin material or non-rigid set ups

User questions & answers

Question:	What cutting tools are recommended for this
Answer:	3/8" AL square shank brazed carbide or a 3/8 square tool bit

Product description

Here is a 3-pc. fly cutter set that-Inch's hard to beat. each is supplied with black oxide finish a setscrew flat and a blank high speed steel tool.

• Stand Included
• 1/2" Shanks
• 3/4", 1-1/8" and 1-3/8" Head Sizes
• 3/16", 1/4" and 5/16" Bit Sizes

User questions & answers

Question:	Can these be used in a router (16,000rpm
Answer:	No that would be a very bad idea

• Comes with inserts installed. InsertS: APKT1604, Tin Coated.
• Positive rake 90Degree, right hand cut. Shank Size: R8. Overall Length: 6-1/8".
• Insert Style: APKT. Insert Size: 1604.
• Number of Flutes: 5. Cutting Angle: 90.
• Coolant Through: No

User questions & answers

Question:	What is the best insert for highest finish quality on face milling Aluminum
Answer:	10w 30 woyld recommend, if you happen to upgrade the en3bt removing the govenor and other stuf along side id suggest 10w 40
Question:	What is the thread pitch for the draw bar? My machine is
Answer:	Roughly 30mpg
Question:	Is this made in China
Answer:	Can be delivered to your house just make sure someone is at the house to sign paper to the truck driver who delivered it to the house
Question:	What is the difference between this 1” face mill and your other 1” face mill (0046-0915). One better for steel than the other
Answer:	About 30mph

Product features

Features

• 90 degree indexable face milling cutter with carbide APKT 1604 inserts
• 75 degree indexable face milling cutter with carbide APKT 1604 inserts
• 90 degree indexable face milling cutter with carbide TPG inserts
• 75 degree indexable face milling cutter with carbide SPG inserts
• 90 degree indexable face milling cutter with carbide TPG inserts and nickel plated bodies
• 75 degree indexable face milling cutter with carbide SPG inserts and nickel plated bodies
• 90 degree heavy-duty coolant-through helical shell indexable milling cutter with carbide APKT 1604 inserts
• 90 degree indexable face milling cutter with carbide TPG inserts and 3/4" straight shanks
• 90 degree indexable face milling cutter with carbide TPG inserts and R8 shanks
• Shell end mill shanks / adapters including R8, CAT40, CAT50, ISO40, etc.

Specifications

Product description

The Multi-Cut 3-in-1 cutting tool is the most versatile cutting tool that everyone should have! Multi-Cut combines a powerful cutter great for cutting through rope, wood, leather, rubber; a wire cutter great for cutting

copper wire, aluminum steel wire; and a retractable utility knife, ideal for cutting boxes, carpet, and drywall!

The razor sharp blade creates incredible cutting power every time! Includes 5 solid steel blades, one assembled

and 4 replacement blades that conveniently store in the handle.

• POWERFUL CUTTER - Easily Cut Thick & Rigid Materials
• RECTRACTABLE UTILITY KNIFE - Retracts to Expose Blade for Cutting Boxes, Carpet, Drywall & More
• TITANIUM COATED WIRE CUTTER - Effortlessly Trim Copper, Aluminum & Steel Wire
• SAFETY LOCK - To Assure It Stays Closed When Not In Use
• INCLUDES - 5 Replacement Solid Steel Blades

User questions & answers

Question:	Where can I get replacement blades
Answer:	Which means you can connect the iPad through wifi and the iPad mini has cellular capability also
Question:	What gauge wire can it cut
Answer:	Sure, Netflix works flawlesly
Question:	Does this come with two cutting tools like it does on their website for 2999 plus shipping and handling
Answer:	Yes!
Question:	Does it cut metal strap
Answer:	The one I have does not.

Product description

R8 Shank Fly Cutter Suitable For Bridgeport Milling Machine 5/16" x 5/16" x 2.1/2" HSS M2 Tool Bit Hardend & Ground Fly Cutter with Allen Key New & Boxed Packed.

• R8 Shank Fly Cutter Suitable For Bridgeport Milling Machine
• 5/16" x 5/16" x 2.1/2" HSS M2 Tool Bit
• Hardend & Ground Fly Cutter with Allen Key