13 best delta wood lathes

Product description

JET JWL-1221VS 12"x21" Variable-Speed Wood Lathe (719200)

• VERSATILITY: 24 integrated indexing positions.
• CONVENIENCE: Easy-to-reach controls and DRO.
• OPTIMAL SPEED: Choose from 60 to 3,600 RPM.
• INNOVATION: Ratchet-style belt tension system (patent pending).
• ON-BOARD STORAGE: Two handy tool caddies.

User questions & answers

Question:	Will 1221 tail stock accept #2 Morse taper drill chuck
Answer:	Yes! Just be sure that the tail stock hole and morse taper are clean, otherwise the #2 morse taper can be difficult to remove...
Question:	has this lathe have a indexing head
Answer:	William, yes this lathe has an indexing head. I have not yet used the feature but it is done with a spring loaded pin which you lock into anyone of 24 positions. The spring loaded pin in screwed in once the pin is set to hold it in place.Rich F
Question:	Is this Ron Swanson approved
Answer:	Yes, Ron personally blesses each unit as it’s loaded onto a truck.
Question:	Do you need to move a belt to change speeds? Or is there a dial or switch
Answer:	This lathe has a variable speed controller, so the speeds may be changed using the simple rotating knob. To provide speed ranges to suit any situation, especially for the more experienced turner, there is a three step pulley. This arrangement allows the variable speed controller to adjust speeds from 60 to 900 rpm on the low step of the pulley, 110 -1800 rpm on the 2nd step (medium), and a high speed range of 220 -3600 rpm on the the 3rd step. The belt need only be changed if you want to move to a different range of speeds. This is a very simple process.

Product features

JET 12'' X 21'' Variable Speed Wood Lathe - JWL-1221VS

The JET 1221VS lathe is different from anything we’ve made before. In truth, it’s different from anything that anybody has ever made before. The design is better. The features are better. The entire turning experience is better. And it all focuses on one concept … Control.

Product description

1/3 Horsepower bench top lathe with variable speed motor

• Motor: 1/3 HP, 2 Amp, 110V, Single-phase, 60 Hz
• 12-inch distance between centers
• 8-inch swing over bed
• Cast iron construction and infinitely variable speed control
• Includes two tool rests

User questions & answers

Question:	I have a chuck that is 1"-8tpi female thread (nova 48111), it doesn't fit on this lathe. what adapter should i buy
Answer:	Buy a 3/4" 16 TPI to 1" 8 TPI adapter. If you further questions go to http://www.woodturningz.com/downloads/w1704_ds.pdf for the specs on this machine.
Question:	is there an adapter for the face plate for mounting live center chucks? I bought one but won't line up with holes
Answer:	I'm not sure if they make the adapter to mount on the face plat. I have a 2" diameter three jaw,self centering scroll type chuck that i bought from Amazon that ihave used that works great,but i think that the holes in the face plate is for mounting a backing block to the piece of wood stock to turn a bowl. It says in the manual that you glue the block to the wood your turning and use the holes to screw the block on to face plate. Hope this helped.
Question:	What size wood stock can it hold? How about something like 12'' long by 8" wide piece of wood
Answer:	The length it will hold will be dependant upon what chucks you have in the head and tail stock. The bulkier the chucks, the shorter the length it will handle. I'd say it will hold 12" lengths unless your chucks are sizable. I wouldn't try more than 4" width stock unless it was short. Although the lathe may hold the stock, it would be too much for the motor. The intended purpose of this lathe is to make small things like ink pens, Christmas ornaments, small toys like tops or yo-yo's and tool handles etc. If you want to mount 12" X 8" stock you should be looking at full sized lathes.
Question:	is there anyway to secure to a bench
Answer:	Yes. It has has three holes in the base that you can bolt it down with. I bolted mine down on a metal stand. It holds it down real solid. Mine is the Shop Fox W1704 also. It is well built. I really like mine. Hope this helps!

Product features

Shop Fox W1704 Benchtop Wood Lathe

Tackle pen turning or other small cutting or shaping projects using the Shop Fox W1704 bench-top lathe from Woodstock International. Made of cast iron, and designed to fit neatly on a workbench, this lathe features a 1/3-horsepower, variable-speed motor and delivers spindle speeds between 700 and 3,200 revolutions per minute (RPM). It also features a safety paddle switch, an MT No. 1 spur center, an MT No. 1 live center, 4-1/4-inch and 7-inch tool rests, a 5-3/4-inch faceplate, and a 3/4-by-16-inch TPI RH spindle.

Includes Two Tool Rests

The W1704 includes both a 4-1/2 and 7-inch tool rest for various turning applications and with a 13-inch distance between centers and an 8-inch swing over the bed this lathe is ideal for a variety of turning projects.

Variable Speed

The infinitely variable speed from 700-3200 RPM comes in handy when turning hard or soft species of wood.

5-3/4-inch Faceplate Included

This benchtop lathe includes a 5-3/4-inch faceplate which threads onto the headstock spindle for non-spindle turning (usually used for making bowls or other items that cannot be supported from the tailstock).

Product description

Includes Reversible NOVA G3-D Woodturning Chuck - 46-461.

• Auto-Stop Jaw Slides inhibit the widening of the chuck jaws beyond their optimum clamping range insuring the material is properly secured
• Anti-Release Spindle Lock is an exclusive DELTA feature that ensures the chuck will stay securely mounted on the lathe during forward and reverse turning applications
• Enhanced jaw gearing provides extra smooth jaw movement and increased clamping pressure for maximum material support
• Threaded chuck jaws increase surface contact with the material offering more secure clamping

User questions & answers

Question:	What is the maximum rpm this chuck is rated for
Answer:	The max speed you would use has more to do with the diameter and the complexity of the item on a wood lathe. If you are bowl turning I have been told a 6" bowl can be turned safely between 1000-1500 rpm by this rule, a 9" bowl at a maximum of 1000 rpm, a 12" bowl 500-750rpm and so forth. Finials could be turned at 2000 rpm. This chuck can easily handle all of that. Hope this helps.
Question:	Will this fit my delta 1642 lathe without adapters
Answer:	This chuck is pre-threaded at 1" 8 threads per inch. The 1642 lathe is most likely 1.25" or 1.50" and 8 threads per inch. So, most likely you will need an adapter.
Question:	is this self centering? whats the max size stock it can handle
Answer:	Yes they are self centering. I believe they can handle stock about 4 1/2 inches. I had bought a different chuck that cost almost as much as this one, but only had one set of jaws. I sent it back, and got this one. It is the best thing that I have bought for turning wooden boxes, and bowls. It seems to be very good quality at a very reasonable price. I got another set of jaws that will hold up to 8" on Amazon for $31.19. The item # is PSI Woodworking CJAWFJ2 Jumbo Flat jaws. I hope this helped.
Question:	Every time i clamp a piece of wood into this chuck, it spins free as soon as i apply any pressure with a tool. what am i doing wrong
Answer:	What's spinning, the wood or the chick? I'll try and help but without seeing what's going on I'm not sure I can help. Ok so the first thing your doing is rotating it on your lathe, then your tightening the hexnuts that are on the chuck 2 of them. Then your putting your wood into the chuck and tightening it fully with your chuck key. After that you should be able to bring up the tail stock and lock it in place, then turn the handle until the wood is snug in between centers. Best of luck, hope this helps. You might also check some YouTube videos on getting set up.

Product features

Precision Machining

The Delta Industrial Reversible Nova G3-D Wood turning Chuck is designed to offer you the latest innovation for professional turning results

Product description

The new JET 1015VS is an ideal choice for the novice woodturner looking for an affordable, user-friendly first lathe, as well as the advanced enthusiast or professional who wants to add a full-featured mini-lathe to the shop. This sturdy, smooth-running 15" mini-lathe has the power, precision and versatility to turn out any number of projects. When you're ready to make your ideas a reality... Start Here.

• 15-1/2" BETWEEN CENTERS
• THREE SPEED RANGES: 200-1,050 / 300-1,750 / 600-3,600
• INTEGRATED 24-POSITION INDEXING
• EASY ACCESS TO BELTS: Improved tensioning system
• INCREASED RIGIDITY: Wider bed ways

User questions & answers

Question:	Does this lathe come with a stand
Answer:	No but one if available as an accessory.
Question:	Can I get parts in Canada for this lathe? Can it be shipped to canada
Answer:	CPO Outlets does not ship to Canada. For support in Canada, please contact Jet directly for guidance at 888-274-6848.
Question:	How accurate is the headstock to tailstock alignment
Answer:	As best I can tell, on mine it is very accurate.
Question:	Does this lathe have a reverse
Answer:	No, mine doesn’t. The larger, more expensive models may.

Product features

JET 10" x 15" Variable Speed Wood Lathe - JWL-1015VS

The new JET 1015 is an ideal choice for the novice woodturner looking for an affordable, user-friendly first lathe, as well as the advanced enthusiast or professional who wants to add a full-featured mini-lathe to the shop. This sturdy, smooth-running 15” mini-lathe has the power, precision and versatility to turn out any number of projects. When you're ready to make your ideas a reality... Start Here.

Product description

Ideal chisel kit for turning pens pepper mills spindles bowls and lots more woodturning projects of all sizes Each chisel measures 16-1/4" in length with a 6-1/4" M2 High Speed Steel blade and a 10" hardwood turned handles Set includes chisels 3/16" Parting Tool 5/8" Spear Scraper 1" Skew Chisel 5/8" Skew Chisel 5/8" Round Nose Scraper 1/2" Bowl Gouge 3/4" Spindle Gouge 7/8" Roughing Gouge Includes wooden case for storage and carrying Great for woodworkers woodturners and penturners of all skill levels

From the Manufacturer

We have assembled this 8-piece set to satisfy the majority of your turning needs. It is suitable for turners of all skill levels. It is the ideal kit for turning small pens, spindles, bowls and larger projects. The M2 High Speed Steel 5-1/4-Inch blades outlast high carbon steel 6-to-1 and will give you years of use. The set includes 8 essential chisels: 3/16-Inch Parting Tool, 5/8-Inch Spear Scraper, 1-Inch Skew Chisel, 5/8-Inch Skew Chisel, 5/8-Inch Round nose scraper, 1/2-Inch Bowl Gouge, 3/4-Inch Spindle Gouge, 7/8-Inch Roughing Gouge. It also comes with beautifully turned 10-3/4-Inch hardwood handles in an attractive wood display box

• Ideal chisel kit for turning pens pepper mills spindles bowls and lots more woodturning projects of all sizes
• Each chisel measures 16-1/4" in length with a 6-1/4" M2 High Speed Steel blade and a 10" hardwood turned handles
• Set includes chisels 3/16" Parting Tool 5/8" Spear Scraper 1" Skew Chisel 5/8" Skew Chisel 5/8" Round Nose Scraper 1/2" Bowl Gouge 3/4" Spindle Gouge 7/8" Roughing Gouge
• Includes wooden case for storage and carrying
• Great for woodworkers woodturners and penturners of all skill levels

User questions & answers

Question:	Do i need to have a high speed bench grinder or slow speed
Answer:	Slower is better than higher. Try not to use a wheel that is lower than 80 grit. 100 seems best. If you go up to high, you end up heating the tool too much.
Question:	are these benjamins best
Answer:	Yes, these are the Benjamins Best tools. I'm enjoying them very much.
Question:	What type of grinding wheel should I use to sharpen these chisels, being made with M2 High Speed Steel
Answer:	For scrapers and gouges, I use a belt sander. For skews and bedans I use a wet stone grinder. I use a polishing wheel with emery compound to hone all my blades between sharpenings.
Question:	Are these "Benjamins Best" (as recommended by Wood Magazine)? Description doesn't say
Answer:	My set has "Benjamins Best" stamped right on the handles.

Product features

HSS Wood Lathe Chisel Set

We've assembled this 8 piece set to satisfy the majority of your turning needs suitable for turners of all skill levels. An ideal kit for turning pens or much larger projects on lathes of any size. The set includes 8 essential chisels with beautifully turned hardwood handles packaged in a practical and attractive wood display box.

Product description

Remember when you could turn heads with your woodturning? Fill your house with as many pens, table legs, and bowls as you can with the WEN 12-Inch Variable Speed Multi-Directional Wood Lathe. Boasting a 4.5-amp motor, take on wood up to 16 inches long and 12 inches wide. If that’s not enough space, mount your workpiece and tool rest onto the back faceplate to turn bowls up to 16 inches in diameter. Adjust the variable speed anywhere from 500 to 2500 rotations per minute with the onboard digital speed display illuminating the current RPM. Change the rotational direction of the lathe from forward to reverse as needed with the simple flip of a switch. The WEN Variable Speed Multi-Directional Wood Lathe features an MT2 spindle and tailstock taper to tightly grip workpieces and a 7-7/8 inch tool rest to provide needed support for chisels and tools during operation. The additional rear support provides a separate place to install your banjo and tool rest for better access when chiseling bowls and other round projects. The easy-to-use lever clamping system makes adjustments to both the tool rest and the tailstock simple and precise. Soft startups prevent damage to both your workpiece and your motor. For additional length, the WEN 34027EX Bed Extension can be purchased separately to increase the maximum capacity from 16 inches all the way up to 39 inches. And, because it’s a WEN product, your lathe comes backed by a two-year warranty, a nationwide network of skilled service technicians and a friendly customer help line. Remember when you could turn bowls, cups, chess pieces, table legs and more? Remember WEN.

• Adjust the variable speed anywhere from 500 to 2500 rotations per minute in either direction
• Attack workpieces up to 12 inches wide and 16 inches long
• Exterior back plate turns bowls up to 15.75 inches in diameter (see figure 3)
• Featuring a digital speed display, a 7-7/8 inch tool rest, a soft start 4.5-amp motor, a face plate, a center spur, a live center, and a two-year warranty
• Increase the capacity to 12 x 39 inches with the WEN 34027EX Table Extension (sold separately)

User questions & answers

Question:	What is the thread size on the spindle
Answer:	This is not a lathe, it has no spindle. it is a standI
Question:	How many horsepower is this lathe? The initial description shows 10a motor but the extended description shows 4.5a motor. Confusing
Answer:	Roughly 3/4 but the banjo will be short and not extend to the compliment of the lathe measurements. I tried to get it fixed and they tried to charge me for the proper figment part. Be warned.
Question:	v ir 110v
Answer:	All small lathes this size are 110V that I have seen. Best I can do.
Question:	Does the tail piece accept a chuck and if so what is the cost
Answer:	Yes, 1/32" - 5/8" Heavy /Duty Drill with chuck key and MT2 shank $36.95 I use it for center holes. When you install the chuck, crank in the on a piece of wood to the turn plate to insure locking.

Product features

Variable Speed Operation

Adjust the variable speed anywhere from 500 to 2500 rotations per minute with the onboard digital speed display illuminating the current RPM.

MT2 Spindle & Tailstock

With threads measuring in at 1 inch by 8 TPI, the included MT2 spindle and tailstock allow for a variety of accessories.

4.5 Amp Slow Start Motor

Our powerful 4.5 Amp motor starts gradually to prevent motor damage and maximize safety. Change the rotational direction with the flip of a switch.

Variety of Accessories

The WEN Lathe includes a 7-7/8 inch tool rest, a face plate, a center spur, and a digital speed display, allowing you to spin a variety of projects.

Product description

These bearings are used on Heavy Duty 12" Lathes from the 60's and later that use a wider bearing on the inboard side than the outboard side of the spindle.

• Rockwell/Delta Lathe Spindle Bearings for 12" Heavy Duty Lathes.
• Used on 4-speed models: 1460, 46-200, 46-203, 46-204, 46-221, 46-222, 46-223, 46-224, 46-305 and variable speed models: 46-525, 46-541, 46-542, 46-543, 46-544, 46-545, 46-612, 46-613
• The inboard bearing is 52mm OD, 25mm ID, and 20.5mm wide. The outboard bearing is 52mm OD, 25mm ID, and 15mm wide.
• Replaces Rockwell/Delta Part Numbers: Inboard Bearing: SP-5334, 920-07-080-5334, or ND 55505, Outboard Bearing: SP-5360, 920-04-020-5360 or ND77505

Product description

The JET JWL-1015 is an ideal choice for the novice woodturner looking for an affordable, user-friendly first lathe, as well as the advanced enthusiast or professional who wants to add a full-featured mini-lathe to the shop. This sturdy, smooth-running 15” mini-lathe has the power, precision and versatility to turn out any number of projects. When you're ready to make your ideas a reality... start here.

• 15-1/2" BETWEEN CENTERS
• SIX SPINDLE SPEEDS: 500/840/1,240/1,800/2,630/3,975
• Integrated 24-position indexing
• IMPROVED TENSIONING SYSTEM: Easier access to belts.
• INCREASED RIGIDITY: Wider bed ways.

User questions & answers

Question:	Can you add an extendion table on it to turn long spindel legs
Answer:	Yes! You just can't buy it on amazon..rockler and woodcraft sell them for around $150.
Question:	Is it a Morse taper
Answer:	Yes both the head stock and tail are #2
Question:	what is needed with this lathe for pen turning
Answer:	Basically, you will need a 7mm MT2 mandrel and your tools. When you order your pen kits, make sure you get the bushings and drill bit. Depending on how you finish the pens, you may need a buffing system. For acrylics, get a set of micro pads, they really bring the shine out. I also use a "french polish" and shellac to put a lasting hard coat on the finished product. Good luck and enjoy the lathe.
Question:	what is the thread size on the head stock
Answer:	Headstock Spindle Thread is 1" x 8 TPI.Complete data sheet is here:http://content.jettools.com/assets/manuals/719100_man_EN.pdf

Product description

Do you want a lathe that’s as versatile as your turning? The 1440 lathe from JET can be tailored to accomplish a wide range of projects. With a sliding and pivoting headstock, variable speed, and many other great features this lathe meets the needs of woodturners. Experience the JET 1440 lathe and see how versatility takes shape.

• VARIABLE SPEED: 400 to 3,000 RPM
• HEADSTOCK PIVOTS 360° WITH 7 POSITIVE LOCKING POSITIONS
• EASY-TO-READ RPM DISPLAY
• POSITIVE LOCKING TOOL REST WITH REDESIGNED CLAMPING
• CSA CERTIFIED

User questions & answers

Question:	The lathe comes with a factory warranty of 5 year but Amazon offers a different warranty of 4 years for $35.54. Do I really need to pay extra
Answer:	That is a call for you to make. At the price, I took it
Question:	Can it be used as a benchtop, without the legs
Answer:	Yes but lock down with bolts or clamps
Question:	Does it have a reverse switch
Answer:	My jet JWL-144VSK does not run in reverse
Question:	Is 400 rpm minimum speed too fast for some operations
Answer:	400 rpm is slow enough of my needs, I've never felt uncomfortable turning at that speed. Also I'm not fussy guy, so for what its worth.

• 【1/2 HORSE POWER MOTOR】- 1/2 Horse Power motor, Voltage: 120V. The powerful  motor starts softly offering motor's maximize safety and low noise.
• 【4 GRADE SPEEDS】- The adjustable belts can be adjust with ease and accuracy within 3400 RPM, 1100, 1600, 2300, 3400prm available.
• 【LARGE WORK CAPACITY】- 40" (1000mm) distance between centers, Cutting Diameter 14" (350mm). High concentricity. Moving tailstock to adjust proper distances for workpieces.
• 【SOLID STEEL CONSTRUCTION】- Solid steel constructed wood lathes for durability and strength, providing increased stability and smooth operation, reducing vibration.
• 【FREE WRENCHES & CHISELS】- 3 wrenches are for easy using and maintainance. 3 chisels for free also, 1 x Skew Chisel, 1 x Shear Scraper and 1 x Spindle Gouge.

User questions & answers

Question:	Can you do aluminum
Answer:	It was not be cost effective because you would need too many attachments. You’d have to modify the tool rest. It would turn it but you couldn’t hold the tool to turn it without modifications. There are lathes out there built for using with aluminum. Hope this helps
Question:	Will the wen la4444 4-inch 4 jaw self centering chuck set with -inch x 8 tpithread fit this lathe
Answer:	https://www.amazon.com/gp/product/B000KI8CBQ/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1 This is what you need
Question:	does this brand and model come in 220 volt
Answer:	Only 110 volts
Question:	What are the minimum and maximum clamping measurements
Answer:	0 to 40 inches

Product features

Powerful Motor

1/2 Horse Power motor, Voltage: 110V, starts softly to offer motor's maximize safety and low noise design.

Variable Speed

Optimally designed speed ranges of 1100-3400 RPM variable speed.

Large Work Capacity

40" (1000mm) distance between centers, swing over bed 14" (350mm). High concentricity.

Accurate & Stable

Steel constructed mini lathes is of increased stability and smooth operation.

7W LED Work Light

3 wrenches are for easy using and maintainance. 3 chisels for easy carving work.

Wide Application

Wood turning lathe, an ideal tool for various operations such as cutting, sanding, knurling, drilling, or deformation.

14 in. x 40 in. Wood Turning Lathe & Variable Speed 3400RPM

Our 14 in. x 40 in. Variable Speed Wood Turning Lathe features variable speed 1100-3400 RPM, a 1/2hp motor. Soft startups ensure safety to both workpieces and the motor. Precise design is perfect for high speed sanding and polishing of finished work.

Product description

Remember when you had maximum versatility with your wood lathe? Take on projects of all shapes and sizes with the WEN 2.75-Inch 4-Jaw Self-Centering Keyed Chuck. This versatile chuck features dovetailed jaws, allowing you to grip the outside of stock between 1-1/8 to 1-3/4 inches in size, or to hold internal pilot holes ranging from 1-1/2 to 2-1/8 inches in diameter. If that’s not enough, you can also install the included screw chuck depending on the task at hand. Indexed backplate indicates 24 different positions while the included tools make for easy adjustments to the chuck. The 1” x 8TPI mounting thread fits a wide variety of wood lathes, including the WEN 3420, 3420T, 3421, 3424, 3424T, 34018, 3427, 34018, 34027 and 34034. NOTE: max recommended workpiece size for 3420, 3420T, and 3421 is 4 inches.

• Scroll chuck perfect for holding bowls, spindles, and other unwieldy wood lathe projects
• Internal jaws tighten around workpieces varying from 1-1/8 to 1-3/4 inches in size
• External jaws spread inside of workpieces with pilot holes ranging from 1-1/2 to 2-1/8 inches
• Keyed tightening mechanism provides additional grip strength to the workpiece
• Features a 1” x 8 TPI thread for compatibility with the majority of wood lathes on the market

User questions & answers

Question:	will this fit on my jet 1014 mini lathe
Answer:	It will if your headstock threads are 1"dia. with 8 threads per inch. Most small to medium size lathes are 1" x 8TPI.
Question:	Ive seen chucks that say 3-m8 and this one says 1-m8. My lathe is 1-m8tpi will a 3-m8 fit my lathe
Answer:	No
Question:	Will this fit my Performax mini lathe? Mod
Answer:	it should not ok, but if not, you could use an adaptor to convert from the lathe spindle size to the chuck female size. This is a great little chuck for the money.
Question:	Will this fit on the wen 3420t 8 in. x 12 in. variable speed benchtop mini wood lathe
Answer:	Yes. They both use a 1" - 8tpi thread. It also comes with an additional adapter threaded into it that you remove.

Product features

WEN LA4275 2.75-Inch 4-Jaw Self-Centering Keyed Lathe Chuck Set with 1-Inch x 8TPI Thread

Remember when you had maximum versatility with your wood lathe? Take on projects of all shapes and sizes with the WEN 2.75-Inch 4-Jaw Self-Centering Keyed Chuck. This versatile chuck features dovetailed jaws, allowing you to grip the outside of stock between 1-1/8 to 1-3/4 inches in size, or to hold internal pilot holes ranging from 1-1/2 to 2-1/8 inches in diameter. If that’s not enough, you can also install the included screw chuck depending on the task at hand. Indexed backplate indicates 24 different positions while the included tools make for easy adjustments to the chuck.

Features

• Scroll chuck perfect for holding bowls, spindles, and other unwieldy wood lathe projects
• Internal jaws tighten around workpieces varying from 1-1/8 to 1-3/4 inches in size
• External jaws spread inside of workpieces with pilot holes ranging from 1-1/2 to 2-1/8 inches
• Keyed tightening mechanism provides additional grip strength to the workpiece
• Features a 1” x 8 TPI thread for compatibility with the majority of wood lathes on the market

Product description

The SHOP FOX W1836 Wood Lathe is packed with features that wood turners love. A powerful 3/4 HP motor with electronic variable-speed spindle control and a digital RPM readout for precise speed adjustments make this lathe a top choice. 24 indexes in increments of 15 allow evenly spaced cuts while the headstock stays in a locked position which opens new possibilities not available on most bench top lathes. Heavy-duty cast iron construction and rubber feet for increased stability and smooth turning operations.

• 3/4 HP, 110V, single-phase, universal motor
• Electronic variable-speed spindle control with digital RPM readout
• 12" swing over bed
• Two spindle speed ranges: 500-1800 RPM & 1000-3800 RPM

User questions & answers

Question:	Are there any holes in feet of lathe to anchor it to a bench
Answer:	You can remove the feet to anchor it.
Question:	Does this come with the light pictured
Answer:	The light pictures is included with the purchase for this unit.
Question:	Will a Nova G3 chuck fit this lathe
Answer:	Yes. It works perfectly.
Question:	How many jaws the head has
Answer:	Mine only has an MT#2 taper. You will have to purchase a jaw set with that taper.

Product features

Shop Fox W1836 Benchtop Wood Lathe

The Shop Fox W1836 Wood Lathe is packed with features that woodturners love. A powerful 3/4 HP motor with electronic variable-speed spindle control and a digital RPM readout for precise speed adjustments make this lathe a top choice.

24 Index Positions

24 index points in increments of 15 degrees allow evenly spaced marking or cutting while the headstock stays in a locked position, this opens new possibilities not available on many benchtop lathes.

Variable Speed Control

The W1836 features variable speed control for on-the-fly speed adjustments. Two overlapping speed ranges ensure maximum spindle torque within each range.

Heavy Duty Live Center

The W1836 includes an MT#2 live center so you can start turning spindles right away. The live center installs into the tailstock quill with a tapered fit and the over sized precision ball-bearing design ensures superior turning operations with stability and no resistance.

Cast Iron Tailstock

Quickly and easily adjust the tailstock to accommodate workpieces up to 15 inch in length. The tailstock is secured with a cam-action clamping system for a rock solid grip.

Tool Holder

This lathe features a convenient tool holder for storing your chisels, extra centers and other tools when not in use.

Optional Bed Extension

The optional D4562 Bed Extension can be added to get you the capacity of a much larger lathe at a fraction of the price. This extension bed increases the capacity of your W1836 Shop Fox Benchtop Wood Lathe to handle pieces up to 38 inch long, long enough for balusters and even baseball bats.

Product description

Keep your chuck securely mounted on your lathe with this Nova Direct Thread 1-Inch X 8TPI G3 Chuck Bundle. Forward and reverse turning applications just became easy, efficient, and safe with this chuck bundle set. The anti-release spindle lock is reversible and increases stability. One-handed geared action capability gives you a powerful and positive grip, and thus piece of mind while you use your lathe. The small size and light weight minimizes the load on small spindles and bearings. Fast operating action makes this set ideal for production turning of smaller pieces. Advanced features, like the automatic jaw safety stop and copper impregnated jaw slides, increase safety and effectiveness. Don't settle for less than the best. Make your lathe is as effective as possible with this Nova Direct Thread 1-Inch X 8TPI G3 Chuck Bundle.

• SAFE AND SECURE: Anti-release spindle lock (reversible); Ensures chuck will stay securely mounted on the lathe during forward and reverse turning applications
• MINIMIZES LOAD: Small size (85-milimeter/3.35-inch) and weight minimizes load on small spindles and bearings
• FAST OPERATING ACTION: Ideal for production turning of smaller pieces; One-handed geared action; Powerful and positive grip
• ADVANCED FEATURES: Automatic jaw safety stop, copper impregnated jaw slides, and direct thread 1-inch x 8TPI dual thread
• SPECIFICATIONS: Up to 350-millimeter/14-inch diameter bowls (using 50-millimeter jaws); Up to 150-millimeter/6-inch length spigots (using 50-millimeter jaws); Takes the same accessory range as all other NOVA chucks

User questions & answers

Question:	I need an adapter with a 3/4-16 id thd and 1-8 od thd does nova made one to fit the g3 chuck bundle
Answer:	I am not that familiar with the full Nova line of products. Have you tried to Google it? Those are fairly common sizes so you might find one. Good luck!
Question:	I have an old craftsman 12" , 103 model. its a 3/4" 16tpi. is there an adapter available that would work with this set
Answer:	Check with at woodworkers parts house. I have seen adapters for the smaller 3/4 inch shafts
Question:	What is the thread size of this chuck
Answer:	The 30th anniversary G3 is a dedicated 1” 8tpi chuck, same as the spindle on my delta 46-460 lathe. It doesn’t not accept the normal Nova threaded inserts since it is a dedicated type rather than insert type. Should also work on the harbor freight lathes as well as any o ther with a 1” 8tpi spindle. It also have a grub screw for lathes with reverse
Question:	Will this work on the Jet mine and Jet mid Lathes
Answer:	I have a Jet 1221VS and it works just fine. Be sure to check the TPI of the lathe headstock. The TPI of your chuck should match. Also check the length of the headstock and the chuck are the same. Although these are not officially standard, they are frequently the same from one device to another. Long story short the... The Nova G3 works just fine on the Jet 1221VS.