9 best powerbuilt steering wheels

• For depressing lock plates on GM and Chrysler vehicles
• Allows removal of round wire snap ring that retains lock plate
• Reversible adapter includes 9/16"-18and M14-1.5 threads.
• Depresses lock plate
• Allows removal of round wire snap ring that retains lock plate
• Reversible adapter includes 9/16 inch-18 and M14-1.5 threads
• Lifetime warranty

User questions & answers

Question:	Will this fit a 1989 Cadillac deville ?? Yes i
Answer:	will it fit on a 1970 Monte Carlo?
Question:	will it work on a 92 s
Answer:	Yes it should
Question:	Will this work on a 1984 K5 blazer (no tilt
Answer:	For depressing lock plate on GM and Chrysler vehicles. Allows removal of round wire snap ring that retains lock plate. Reversible adapter includes 9/16"-18 and M14-1.5 threads.
Question:	Is this the appropriate tool to remove the steering wheel on a 1998 chevy truck
Answer:	This is for removing the lock plate after removing the steering wheelhttp://www.harborfreight.com/steering-wheel-remover-set-68982.htmlThis kit will help you get the job done.

Product features

Powerbuilt Steering Wheel Lock Plate Remover

Step for Usages:

• Match the thread on the adapter to steering shaft and back off wing nut fully
• Thread adapter onto end of steering shaft
• Back plastic handle of tool out until there is tension on the tool
• Thread wing nut down until sufficient pressure is applied to lock plate to release snap ring

Features:

• For depressing lock plates on GM and Chrysler vehicles.
• Allows removal of round wire snap ring that retains lock plate.
• Reversible adapter includes 9/16"-18 and M14-1.5 threads.
• Heat treated steel material for strength

• For removing steering wheels on most domestic and imported vehicles
• Heavy duty drop-forged steering wheel puller fits most domestic and imported vehicles, with or without telescopic or tilt steering columns
• Kit includes the following size bolts in a handy storage case: Set of M8-1.25x80mm, 1/4"-28x3" NF, 5/16-24x3 1/2" NF, 5/16-18x4 1/2" NC, 3/8"-16x4" NC.
• Pulls steering wheels on most domestic and imported vehicles
• Heavy duty drop-forged steering wheel puller fits most domestic and imported vehicles
• Can be used on steering wheels with or without telescopic or tilt steering columns
• Includes: 2 M8-1.25x80 millimeter, 2 1/4 inch-28x3 inch national coarse, 2 5/16-24x3 1/2 inch national fine, 2 5/16-18x4 1/2 inch national coarse , 2 3/8 inch-16x4 inch national coarse
• Blow-molded case included to keep tools organized

Product features

Powerbuilt Heavy Duty Steering Wheel Puller

Remove steering wheels from most domestic and imported vehicles with this heavy duty steering wheel puller. Drop-forged for strength, this steering wheel puller works on steering wheels with or without telescopic or tilt steering columns.

Any automotive specialty tool makes an automotive repair or maintenance task easier, but Powerbuilt takes the concept of ‘help’ a big step further.

Every package comes with professionally written usage instructions and photos that take you step by step through proper tool usage.

Dependable Powerbuilt specialty tools offer power, precision and style. They meet or exceed applicable ANSI standards.

• Drop-forged heavy duty steering wheel puller
• Fits most domestic and imported vehicles
• Includes M8-1.25x80mm , 1/4"-28x3" NF , 5/1624x3 1/2" NF , 5/16-18x4 1/2" NC , 3/8"-16x4" NC bolts

• Powerbuilt steering wheel puller Set
• Design to pull steering wheels on most domestic and imported vehicles.
• Heavy-duty drop-forged steel construction
• Made from quality materials
• Durable and long lasting
• Yoke is zinc plated
• Chrome plated 2 piece puller leg

Product features

Powerbuilt Heavy Duty Steering Wheel Puller

Remove steering wheels from most domestic and imported vehicles with this heavy duty steering wheel puller. Drop-forged for strength, this steering wheel puller works on steering wheels with or without telescopic or tilt steering columns.

Any automotive specialty tool makes an automotive repair or maintenance task easier, but Powerbuilt takes the concept of ‘help’ a big step further.

Every package comes with professionally written usage instructions and photos that take you step by step through proper tool usage.

Dependable Powerbuilt specialty tools offer power, precision and style. They meet or exceed applicable ANSI standards.

• Drop-forged heavy duty steering wheel puller
• Fits most domestic and imported vehicles
• Includes 1Pc. Yoke, 1 Pc. Center Bolt, 2 Pc. Puller Leg, 2 Pc. 3/8"-16* Bolt, 2 Pc. 5/16"-24* Bolt, 2 Pc.-5/16"-18* Bolt, 1 Pc. Socket for Center Bolt, and 1 Pc. Adapter for Center Bolt

Product description

Powerbuilt's Steering Wheel Lock plate Remover/Installer is designed for depressing lock plates on GM and Chrysler vehicles, allowing the removal of the round wire snap ring that retains the lock plate. Reversible adapter includes 9/16"-18 and M14-1.5 threads.

• Steering wheel lock plate remover
• For depressing lock plates on GM and Chrysler vehicles
• Allows removal of round wire snap ring that retains lock plate
• Made from quality materials
• Durable and long lasting
• Allows removal of round wire snap ring that retains lock plate
• Depresses lock plates on GM and Chrysler vehicles
• Reversible adapter includes 9/16"-18 and M14-1.5 threads

• Made to be the most reliable tools in the market today
• Tool solutions for most all situations
• Built to exceed tool standards
• Tool set for removal and installation of power steering pump and alternator pulleys
• For use on most power steering pump pulleys
• Includes special installer adapters, puller assembly with thrust bearing, jaw and sleeve
• Storage case includes usage photos
• Kit 20 includes 14-Piece for removal and installation of the power steering pump and alternator pulleys

User questions & answers

Question:	Will this work 2000 nissian extrerra
Answer:	I donk know I bought it for a Honda cr-v
Question:	Will thi kit work on a 2000 dodge dakota 3.9l v
Answer:	I believe so, it fit my 2001 Honda Civic EX perfectly.
Question:	Will this work on a 79 chevy c10 350 sbc
Answer:	No, every tank is different. Different threads, different size. Get the part from the maker of your reservoir tank
Question:	Will this work in an Acadia
Answer:	This cap fit perfectly for my Civic 2003-EX. You may check w your dealer before ordering for your Civic 2005-LX.

Product features

Powerbuilt 14 Piece Pulley Remover & Installer Kit

Replacing a faulty power steering pump is easier when you have the right tools. This innovative kit has a variety of pins and adapters so you can find the one that is a perfect fit. Set can be used to remove and install both power steering and alternator pulleys. Strong and dependable enough to last a lifetime.

Kit Services: Most domestic and import vehicles

Any specialty tool will help make an automotive repair or maintenance task easier, but Powerbuilt automotive installer tools take the concept of ‘help’ a big step further. It starts with the storage case – heavy-duty design ensures it will stand up to years of use and abuse. Inside the case lid you’ll find how to instructions and photos that show step-by-step usage instructions.

The finishing touch? All Powerbuilt installer kits meet or exceed ANSI and/or ASME standards so you can buy with confidence knowing you’ll get quality.

Set includes

• Jaws
• Thrust Bearing and Thrust Washer
• Puller Body
• GM Power Steering Disconnect
• Center Screw Button
• Ford 4.6L and Universal Threaded Adapter
• GM 3.1L V6 and Quad 4 Threaded Adapter
• Center Screw
• GM 3.1L V6 and Quad 4 Puller Pin
• Storage Case

Product description

Alltrade Tools LLC is a global leader in the design, manufacturing and marketing of innovative products for home, garage and worksite. Founded in 1979, Alltrade is privately Held and maintains global sourcing, research, assembly and sales facilities to serve customers on every continent.

From the Manufacturer

Each kit includes step-by-step usage instructions and photos showing the tool in use. Instruction sheets are laminated to resist staining and are permanently fastened to the case. All instructions are developed by a professional repair manual writer. Kit 46 tools are for removing and installing most sizes of press-fit ball joints. Allows change out of ball joint without removal of the control arm. These tools can also be used to remove and replace U-joints. The set includes - 1 PC - PLUG: O.D. 7/8" 1 PC - RECEIVING TUBE: OD: 2-1/4", ID:2", 2"(L) 1 PC - INSTALLING TUBE: OD: 2", ID: 1-3/4", 3"(L) 1 PC - RECEIVING TUBE: OD: 2-1/2", ID: 2-1/4", 1-1/2" (L) 1 PC - RECEIVING CUP: OD:2 -1/4", ID: 1-7/8", 7/16" (L) 1 PC - RECEIVING TUBE: OD:2 1/2", OD: 2-1/4", 3/4" (L) 1 PC - RECEIVING TUBE: OD:2-7/16", I.D:2-3/16", 3-3/16"(L) 1 PC - REMOVER/INSTALLER: OD:1-7/16", I.D:3/4", 1" (L) 1 PC - INSTALLING TUBE: OD: 2", ID: 1-3/4", 2-5/16" (L) 1 PC - RECEIVING CUP: OD: 2-1/8:, ID: 1-3/4", 1/2" (L) 1 PC - RECEIVING TUBE: OD: 2-1/2", ID: 2-1/4", 2-3/4" (L) 1 PC - RECEIVING TUBE: O.D.: 3", ID: 2-3/4", 2-1/4" (L) 1 PC - RECEIVING TUBE: O.D.: 2-3/4", ID: 2-7/16", 2-1/4"(L) 1 PC - RECEIVING TUBE: OD: 2-7/8", ID: 2-5/8", 2-7/8" (L) 1 PC - SCREW 1 PC - C-FRAME 1 PC - RECEIVING TUBE: 1-3/4" X 2" 1 PC - RECEIVING TUBE: 2-1/4" X 2-1/2" 1 PC - RECEIVING TUBE: 2-3/4" X 3" 1 PC - REMOVAL ADAPTER 1 PC - INSTALL ADAPTER 1 PC - 3/4"DR. X 1-59/64". 2"(L) 1 PC - 3/4"DR. X 2-9/64". 2"(L) 1 PC - BLOW MOLDE CASE

• Harm Bal/ crank PULLEY P
• Tool solutions for most all situations
• Built to exceed tool standards
• Designed to help you remove and install press-fit type ball joints without taking the control arm off the vehicle
• Kit services: most Domestic and import rear wheel drive vehicles
• Remove and install pressed-in Ball Joints found on most vehicles
• Remove and install special threaded upper Ball Joints found on many Chrysler vehicles

User questions & answers

Question:	Hi, can anyone confirm this will work with a 2000 wrangler for Ball joints? Thanks
Answer:	This is a universal kit it should work I bought one couple years back saved me so much money so far it actually paid for itself twice
Question:	What size socket is needed to drive the screw
Answer:	It uses a 7/8" socket, and a breaker bar would help you alot too. If you own a shop then this is perfect, if not and just want to service your own car do make sure that the ball joints on your car are pressable (NOT PERMANENTLY PRESSED - you'd just have to replace the whole control arm and not need this kit)
Question:	Is it made in the usa
Answer:	Don't know and can't see any 'Made in the USA' stampings on the components. All I know is that it's built very well, it's strong, and does the job without any problems. Configuring the components to press in/out is a challenge, but I was able to get it to work as advertised. There is a manual that comes with the kit to help out with the configurations. I would definitely recommend this kit!
Question:	will it service a dodge 2500. 2006 yr
Answer:	It should service all pressed ball joints

Product features

Powerbuilt 23 Piece Ball Joint & U-Joint Service Kit

Replacing ball joints is time-consuming enough without having to disassemble half the car to reach them. This innovative tool set is designed to save time and frustration by helping you remove and install press-fit type ball joints without taking the control arm off the vehicle. This set can also be used for removing or installing U-joints. Strong and dependable enough to last a lifetime.

Kit Services: Most domestic and import rear wheel drive vehicles

Any specialty tool will help make an automotive repair or maintenance task easier, but Powerbuilt automotive installer tools take the concept of ‘help’ a big step further. It starts with the storage case – heavy-duty design ensures it will stand up to years of use and abuse.

• Removes and installs press-fit type ball joints without taking the control arm off the vehicle. This set can also be used to remove and install U joints.
• Durable storage case with step-by-step instructions

Set includes:

• receiving tube 2-7/8" OD x 2-7/8" L
• receiving tube 2-7/16" OD x 3-3/16" L
• installing adapter 2" OD x 3" L
• receiving tube 2-3/4" OD x 2-1/4" L
• receiving tube 2-1/4" OD x 2" L
• receiving tube 2-1/2" OD x 1-1/2" L
• installing/removing adapter 3-1/16" OD x 1-1/8" L
• installing adapter 3" OD x 1-1/8" L

• Made to be the most reliable tools in the market today
• Tool solutions for most all situations
• Built to exceed tool standards
• For servicing wheel bearing locknuts found on many Ford, Dodge and Toyota trucks and SUVs
• Carry case included
• Also includes instruction sheet with photos
• Lifetime manufacturer warranty

Product features

Powerbuilt 7 Pc. Wheel Bearing Locknut Remover Kit

Get a grip on wheel bearing locknuts with this 7 piece locknut set. These precision carbon steel locknut sockets are made with your specific vehicle in mind. Size printed on the side of each socket for easy identification. Dependable enough to last a lifetime.

Kit Services: 1990-1993 Dodge trucks with Dana 60 manual hubs, Ford 3/4 ton and 1 ton F-250 and F-350 pickup trucks with manual locking hubs; Toyota Land Cruisers and pickup trucks with front wheel bearing adjusting locknuts; 1990 to current Ford Ranger, Explorer and Bronco II with automatic locking hubs, 1995-96 Ford Bronco and Ford F-150 pickup trucks with automatic locking hubs; 1984-1992 Ford Ranger and Bronco II with automatic locking hubs.

Set includes

• 2-9/16" 6R Locknut Socket
• 55mm 6pt Locknut Socket
• 2-3/8" 6R Locknut Socket
• 2-1/2" 6R Locknut Socket
• 2-1/2" 6pt Locknut Socket
• 2-3/8" 6pt Locknut Socket
• 2-3/4" 6R Locknut Socket
• Storage Case

• BUILT TO LAST: You won't feel flex or sagging when you sit and roll on this beast. With an industrial-grade nylon composite base and steel rider and piston, it's stiff in all the right places and built to last.
• ROLLS SMOOTH: Five 2-inch polyurethane skate wheels roll on ABEC bearings and swivel on ball-bearing races make rolling on carpet and hard surfaces equally easy in any direction.
• WORK AT YOUR BENCH, WORK AT YOUR CAR: You'll use this stool everywhere thanks to the 21-inch to 29-inch pneumatic height adjustment.
• LAND YACHT COMFORT: Take a seat and be transformed - you'll feel like a king cruising the boulevard in a '75 Cadillac Brougham - that's how soft yet supportive this throne on wheels feels.
• BIG BOY APPROVED: Thanks to a wide, stable footprint and 300-pound capacity, everyone is welcome to sit down on the job!

User questions & answers

Question:	Can this hold at 29" or does it drop down a few inches for a person under 200 lbs
Answer:	it should work on the Acadia. It has adapters for each type of pulley.

Product features

Powerbuilt Pneumatic Height Adjustable Rolling Seat Stool

Roll in style and comfort with this industrial-strength roller seat. Sure it’s built tough, with high-grade steel and premium quality nylon. And you’ll love rolling around your garage, man cave, driveway or shop on the 5 polyurethane skate wheels. They swivel on silky-smooth ball-bearings and roll equally well on carpet and cement floors. With 8 inches of pneumatic height adjustment, you’ll use this throne at your workbench or desk, in your garage and driveway, and even at your basement bar when happy hour rolls around. And Big Boys are welcome to sit a spell too, thanks to 300 lb. capacity.

• Heavy-duty steel and nylon construction for years of service
• 2-inch polyurethane wheels roll smooth and swivel on ball-bearing casters
• Easy pneumatic height adjustment from 21 to 29 inches
• Ultra-comfortable 14-inch x 3-inch seating surface
• 300 pound capacity

Heavy-Duty Construction

Height Adjustment from 21" to 29"

14" x 3" Seating Surface

Product features

Powerbuilt 3 Piece Zeon Metric Lug Nut Socket Set for Damaged Lug Nuts

Powerbuilt Zeon lug nut sockets are designed to grip and turn damaged and rounded wheel lug nuts. The patented design will grip and turn lug nuts up to 85% rounded. And they work just as well on new lug nuts.

In other words, if you’ve got a lug nut that you can’t turn, we have the help you need.

The secret is the patented Zeon socket design - the more you turn them the harder they grab and hold damaged hex heads. Zeon lug nut sockets are constructed of premium impact-rated Chromoly steel for unmatched strength and durability. They won't scratch your high-end wheels though, thanks to the included protective plastic wheel saver sleeves.

• Zeon lug nut sockets grab and turn lug nuts are up to 85% rounded
• Works great on new lug nuts too, without damaging them
• Durable Chromoly steel for extra hardness and bite
• Includes 1/2 in. drive Metric lug nut sockets: 17, 19, and 21mm
• Impact rated for use with power tools
• Meets or exceeds ANSI standards