3 best wet look concrete sealer

• The Armor AR350 is a breathable, non-yellowing solvent based acrylic that will darken concrete and pavers to make them look wet, and provide a long lasting, durable low gloss finish.
• The Armor AR350 is manufactured in the US and made from non-recycled resins.
• The Armor AR350 is self-priming and can be applied to unsealed concrete and paver surfaces, as well as surfaces previously sealed with a solvent based acrylic sealer.
• The Armor AR350 will help to reduce damage and deterioration caused by surface abrasion such as dustring, cracking, spalling, and pitting.
• The Armor AR350 can last up to 1-3 years on exterior surfaces and up to 3-7 years on interior surfaces before the need for a recoat.

User questions & answers

Question:	is the surface slippery
Answer:	Don't know as I have not washed the covers as of yet......sorry
Question:	I have paving stones about 1 1/2 inches apart, with gravel in the spaces. Will I be able to effectively put the sealant on without taking out the rock
Answer:	I believe they are only in sets but if you click on the actual profile of the seller it will bring you to all options. They are GREAT covers!!
Question:	How much time do you need to wait before applying 2nd coat
Answer:	Yes just keep in mind that the mat side walls are one inch high install them at first and if you have to drill through the mat into the cabinet be sure to put a bead of silicone around the screw
Question:	what is required for clean up? If I put this in a spayer what would I use to clean out the equipment
Answer:	Yes. Seal with silicon around the cut.

Product features

Uses & How to Apply

The Armor AR350 is a fantastic sealer for poured concrete, stamped concrete, aggregate concrete, and concrete paver surfaces. It can be applied to unsealed surfaces as well as surfaces previously sealed with a solvent based acrylic.

Coverage:

One gallon of the Armor AR350 will cover up to 175 square feet per coat. Two coats are recommended to achieve the maximum life and performance benefits. Coverage can vary depending on the porosity of substrate and the application method.

How to Apply:

• First, make sure that the surface is clean and free of any contaminants that could prevent proper penetration or adhesion. If the surface was wet, allow at least 24 hours to dry.
• In the early evening (5 PM or later), when the surface has had time to cool down from exposure to the sun, apply the first coat using a 3/8" nap roller or solvent-resistant HVLP sprayer. Wait 24 hours and repeat with a second coat.
• Allow the surface 48 to dry before introducing it to water, foot, or vehicle traffic.

Frequently Asked Questions

Will the surface be slippery when wet? Yes, the surface may be slippery when wet because the sealer prevents water from absorbing into the surface. Foundation Armor manufactures a fine non-slip additive and a coarse non-slip additive that can easily be mixed into the sealer before applying.

How long does the sealer last? The Armor AR350 can last up to 2-5 years before the need to reseal. Surface porosity, environment, surface abrasion, and the amount of material applied will ultimately determine the life of the sealer. Typically, exterior substrates are sealed every 1-3 years and interior substrates are sealed every 3-7 years.

Is the Armor AR350 breathable? Yes, the Armor AR350 is a breathable acrylic sealer.

Is the Armor AR350 UV stable? Yes, the Armor AR350 is UV stable and will not yellow from exposure to UV rays.

What if I want a high gloss? If you want a high gloss consider the Armor AR500 instead.

Product description

A good masonry sealer protects and beautifies concrete, brick, and other masonry surfaces while preserving and maintaining color and detail without fading, yellowing or changing color. KILZ Interior/Exterior Sealer is high-solid, non-yellowing acrylic-based formula that enhances coated and uncoated stone, tile, cement, and stucco surfaces with a high-gloss, wet-look finish. Use KILZ Liquid Masonry Sealer indoors and outdoors on masonry, stucco, concrete, tile, brick, aggregate, natural and artificial stone surfaces. Not for use in high moisture areas such as pool decks. This sealer can be applied with a brush, roller, high quality pad applicator, or high quality pump sprayer. The sealer dries within an hour and can be recoated in 4 hours. This is a 1-gallon can of KILZ Interior/Exterior Concrete, Brick, and Tile Clear Liquid Masonry Sealer with a wet-look finish. Covers 250-400 square feet per gallon depending on surface texture. All surfaces must be clean, free of dust, chalk, oil, grease, wax, polish, mold and mildew stains, loose and peeling paint, rust, and all other foreign substances. KILZ Liquid Masonry Sealer can be brushed, rolled, or pump sprayed on. Do not thin. KILZ has been making premium primers and paints for 40 years. KILZ was named Paint Brand of the Year in 2015 in the Harris Poll EquiTrend  Rankings.

• A good masonry sealer protects and beautifies concrete, brick, and other masonry surfaces while preserving and maintaining color and detail without fading, yellowing or changing color.
• KILZ Interior/Exterior Sealer is high-solid, non-yellowing acrylic-based formula that enhances coated and uncoated stone, tile, cement, and stucco surfaces with a high-gloss, wet-look finish.
• Use KILZ Liquid Masonry Sealer indoors and outdoors on masonry, stucco, concrete, tile, brick, aggregate, natural and artificial stone surfaces. Not for use in high moisture areas such as pool decks.
• This sealer can be applied with a brush, roller, high quality pad applicator, or high quality pump sprayer. The sealer dries within an hour and can be recoated in 4 hours.
• This is a 1-gallon can of KILZ Interior/Exterior Concrete, Brick, and Tile Clear Liquid Masonry Sealer with a wet-look finish. Covers 250-400 square feet per gallon depending on surface texture.
• All surfaces must be clean, free of dust, chalk, oil, grease, wax, polish, mold and mildew stains, loose and peeling paint, rust, and all other foreign substances.
• KILZ Liquid Masonry Sealer can be brushed, rolled, or pump sprayed on. Do not thin.
• KILZ has been making premium primers and paints for 40 years. KILZ was named Paint Brand of the Year in 2015 in the Harris Poll EquiTrend  Rankings.

User questions & answers

Question:	Can this be used on concrete that has been painted with satin finish concrete paint
Answer:	Hi there, thank you for your question about our Wet-Look Sealer. This product can be used over the satin finish concrete paint if it's water-based and in good condition. Also, it may be best to reach out to the manufacturer of the paint to check if our sealer can be used over theirs. I hope this info helps.
Question:	Do you sell low-gloss? If so, how do you order it
Answer:	No problems
Question:	The high gloss sealer did not work on my acid stained colored concrete walkway, outdoors. It turned milky white. Now how do I remove the sealer
Answer:	I honestly don’t know When we used the product it was a milky white when applied but by the end of the day the White was gone and the clear gloss appeared. I suggest you go to Lowe’s or Home Depot and ask that question Hopefully they can help suggest a product
Question:	Is the low lustre really low? I do not want my brick shiny
Answer:	This stuff was great and yes it was a low lustre. I put two coats on a concrete patio prior to enclosing it into a room and putting a laminate floor down. It does dry relatively quick so be prepared if you are doing multiple coats.
Question:	I am grouting seashells into a design project. Can this be brushed over them while sealing the abstract lines
Answer:	This should seal any grout.
Question:	How long will this grout sealer last
Answer:	This should last 1-3 years depending on traffic and the types of cleaners used to maintain it.
Question:	Can this be used on travertine stone tile and sanded grout lines without damaging or etching the travertine
Answer:	I put some on my quartz countertop in an inconspicuous spot. No damage. Put it on grout between travertine back splash and quartz and I didn’t see any marks.
Question:	why is everyone reviewing the cleaner on the sealer listing? Anyone on the sealer
Answer:	The cleaner is great. Don't know the sealer.

• Penetrating high solids acrylic coating with unmatched bonding characteristics.
• Durable, long lasting, professional grade solvent based acrylic offering superior performance abilities.
• Satin sheen wet look finsih. Will bring out color in dulled substrates.
• Can be used on poured concrete, stamped concrete, concrete pavers.
• 1 gallon will cover up to 100 square feet in two coats.

User questions & answers

Question:	how does this hold up to deicers and salt
Answer:	Deicers come in many variations. Foundation Armor recommends avoid petroleum deicers. Calcium and Magnesium chloride tend to be less aggressive on surfaces than sodium and potassium chloride. When a surface is properly sealed with the AR350, salts will remain superficial (on the surface) rather than damaging the concrete below. Usually physical abrasion from vehicles grinding salt and sand into the coating is more of a concern than salt directly damaging the coating.
Question:	Im making my own pavers. How long would i need to wait before they can be sealed
Answer:	I waited a year before i sealed my pavers
Question:	Can this bepainter after is is aplied
Answer:	The AR350 should not be painted over. Foundation Armor does offer color packs that will give the AR350 a "paint like" appearance.
Question:	I am trying to decide between this and ar 500. What is the difference in looks between the 2? the floors in pics appear to have same kind of shine
Answer:	Hi Moses, the AR350 is a low gloss and the AR500 is a high gloss. They will both darken the concrete to make it look wet, and they will both provide the same life and benefits.

Product features

Uses & How to Apply

The Armor AR350 is a fantastic sealer for poured concrete, stamped concrete, aggregate concrete, and concrete paver surfaces. It can be applied to unsealed surfaces as well as surfaces previously sealed with a solvent based acrylic.

Coverage:

One gallon of the Armor AR350 will cover up to 175 square feet per coat. Two coats are recommended to achieve the maximum life and performance benefits. Coverage can vary depending on the porosity of substrate and the application method.

How to Apply:

• First, make sure that the surface is clean and free of any contaminants that could prevent proper penetration or adhesion. If the surface was wet, allow at least 24 hours to dry.
• In the early evening (5 PM or later), when the surface has had time to cool down from exposure to the sun, apply the first coat using a 3/8" nap roller or solvent-resistant HVLP sprayer. Wait 24 hours and repeat with a second coat.
• Allow the surface 48 to dry before introducing it to water, foot, or vehicle traffic.

Frequently Asked Questions

Will the surface be slippery when wet? Yes, the surface may be slippery when wet because the sealer prevents water from absorbing into the surface. Foundation Armor manufactures a fine non-slip additive and a coarse non-slip additive that can easily be mixed into the sealer before applying.

How long does the sealer last? The Armor AR350 can last up to 2-5 years before the need to reseal. Surface porosity, environment, surface abrasion, and the amount of material applied will ultimately determine the life of the sealer. Typically, exterior substrates are sealed every 1-3 years and interior substrates are sealed every 3-7 years.

Is the Armor AR350 breathable? Yes, the Armor AR350 is a breathable acrylic sealer.

Is the Armor AR350 UV stable? Yes, the Armor AR350 is UV stable and will not yellow from exposure to UV rays.

What if I want a high gloss? If you want a high gloss consider the Armor AR500 instead.