12 best dimmers for led lights

• 3-Way Single Pole Compatible Slide control dimmer.If UP is off(DOWN is on) after wiring, try switching around the two red wires to reverse the on/off direction
• Fully compatible with Cloudy Bay LED light fixtures,600W max Incandescent,150W max Dimmable LED/CFL,120VAC,60Hz
• Works with LED,Halogen,Incandescent bulbs - Trim Dial below Cover Plate allows Sensitivity Adjustment upon installation to achieve compatibility with LED Lamps
• Decorative Wall Plate and Mounting Screws Included
• UL Listed,1 Year Warranty. Please contact us if there is any issue with dimming issue.

User questions & answers

Question:	Where is it made? USA
Answer:	No sounds from mine. Make sure your bulbs a dimmable type? Just a guess.
Question:	Are there a 2, 3 snd 4 gang wall plates for these
Answer:	I doubt it, but contact mfg., they are very responsive.
Question:	installed but not turning on when the slide is in between and also hear some sound when you keep your ears on switch in dim mode . anyone else faced
Answer:	Check the display is ON or OFF on the top left connor, it should show ON then the device can work.
Question:	can this dimmer be used on 12 volt LED lamps
Answer:	What I think was being asked is if this meter can tell you the PEAK load during the time it was connected. For example, let's say it was connected to a refrigerator for 10 hours. Let's say that during that 10 hours the load in Watts was 150Watts. But, when the compressor kicks in, it surges to 2000Watts for 3 seconds. Will this device allow you to see that 2000Watt PEAK later? Does it store that PEAK load into memory so you can view it?

Product features

SINGLE POLE/3-WAY CIRCUIT INSTALLATION

• Single Pole: Connect the green dimmer ground wire to ground wire in the wall-box, Connect the black dimmer wire to the hot input wire removed from the switch,Connect either of the 2 red dimmer wires to the light fixture wire removed from the switch,Use wire nut to cap the remaining red wire on dimmer
• 3-Way: Connect the green dimmer ground wire to the ground wire in the wall-box, Connect the black dimmer wire to the TAG wire removed from the switch, Connect the red dimmer wires to the remaining wires removed from the switch

Manual Control

At the low end of the dimming level when the light starts to flicker, fine tune the dimming performance by turning the adjustment dial counter-clockwise so that the light output is stable. Set your slider to where there's no hum or flickering on light fixtures.

Screw-free wall plate

Install the dimmer and mounting frame with the tabs facing down. Put on the screw-free wall plate after tuning the adjustment dial.

Compatible with CFL/LED

Cloudy Bay dimmer improves the compatibility of dimmable CFLs and LEDs compared to standard dimmers by eliminating flicker, making sure lights operate properly at all levels.

Trouble shooting

1: Light flash in the whole dimming range

a. Check the lighting/lamp is dimmable or not

b. The lighting fixture is not compatible with our dimmer

c. Most dimmable LEDs and CFLs will not acheive as low level as incandescent or halogen sources.

d. Control a group of lighting fixtures/lamps with one dimmer may cause flicker due to variation of dimming circuit and dimming range. Please use dimmer to

control lights/lamps in the same type or same model.

2. Light flash in low dimming range

a.Slightly turn the adjustment dial counter- clockwise to achieve full compatibility with the lights

3. Get dimmer list from light bulb/lighting fixture's supplier to avoid compatible issue with our dimmer, a broad dimmer list means less dimming issue, such as flicker,buzz, or flash issue, also, better buy FCC compliance lighting product for stable performance.

Product description

Leviton offers a full line of dimmers and lighting controls that bring Energy Smart Living to your Home. These devices easily replace standard wall switches throughout the house and provide an immediate energy payback. Create the perfect mood in any room and save energy by installing dimmers today. Leviton Tabletop Slide Control Lamp Dimmer 300-watt incandescent, 150-watt dimmable LED and CFL bulbs. Black TBL03-10W features: Full range feed through lamp cord dimmer provides convenient tabletop dimming control with easy glide, positive on/off action in Completely insulated housing. Testing and Code Compliance: UL Listed, CSA Certified, and backed by a limited 5-year warranty. Environmental: Flammability UL94 V2 Rating. Operating Temperature: 32 to 130 Degrees F.

• Full range slide control dimmer
• Compatible with incandescent, halogen, dimmable LED and dimmable CFL bulbs
• No installation required
• 6 foot cord makes it easy to reach any outlet
• AC UL listed. Frequency-60 hertz
• Note: "Application guide" under the technical specifications shows our official bulb compatibility list. The customer can use this to find a bulb that will work with this device.

User questions & answers

Question:	does this also have on/off switch
Answer:	Yes, this is also an on/off switch, slide it all the way up to full bright and slide it all the way down to turn off the light
Question:	This I don't have to slice do i? Jus plug in and use? No spicing or anything
Answer:	Very simple device. You plug it in then you plug a lamp or something like that into it's plugin. Then you can control your lamp. It's really quite simple.
Question:	From the reviews, it sounds like this dimmer doesn't have the "buzz" that some do with LED bulbs. Anyone know if it is as quiet with an incandescent bulb
Answer:	It creates a noticeable 120Hz buzz when used with Sylvania 25W Dimmable "Night Chaser" lamps: https://www.amazon.com/gp/product/B07DPDVHMM . It is completely silent when used with CRLight 12W Dimmable "Antique ST64" lamps: https://www.amazon.com/gp/product/B07F322C39 but has almost a 1-second lag.
Question:	How dim will it go
Answer:	We tried to use this to dim to a night light. It was not that dim for LED. The infosheet for a similar product from LUTRON says 300 W should not be used for LED (http://pdf.lowes.com/operatingguides/027557390811_oper.pdf). I suggest this item on Amazon: part number: TTCL-100H-BL; ASIN: B004DZONXI; link: https://smile.amazon.com/Lutron-Credenza-dimmable-Incandescent-TTCL-100H-BL/dp/B004DZONXI/

Product features

Leviton TBL03-10E Tabletop Slide Control Lamp Dimmer

Leviton offers many products that will help lower electrical costs and add convenience to everyday living. Dimmers reduce energy consumption and extend bulb life. Leviton's table top dimmer is an easy way to add the ambiance of dimming to a table or floor lamp, Just plug in lamp and start dimming.

Our Mission

We pledge to provide products and services that go beyond our customers’ expectations—always—by carefully listening to our customers and understanding how they live and work, so we can apply our ingenuity to their real needs.

Our Vision:

We’re working to create a family of companies that protect, connect, and power the world’s most innovative environments every day by pursuing opportunities in new markets, optimizing profitability, and accelerating the growth areas that enable us to deliver best-in-class solutions.

Our Values:

We’re committed to promoting an open, honest and trustworthy culture, where each employee is respectful of our customers, vendors and one another. Driven by the needs of our customers and by industry standards, we strive for continuous improvement in all we do as we elevate the quality of our products, services and system solutions.

Product description

Lutron LED+ dimmers provide the best dimming performance for LED bulbswhile setting the right light level to improve mood and ambiance for any activity. Designed specifically for dimmable lads and CFL, as well as for use with traditional incandescent and halogen bulbs, they greatly improve the dimming performance when compared to standard dimmers. Featuring advanced circuitry designed to alleviate common challenges, like flicker and pop on, LED+ dimmers are compatible with 800+ bulbs- for more specific details on compatible bulbs, view "technical specification" below. The Diva dimmer matches existing decor a style switches and fits in a standard decor a style wall plate (CW-1-WH). It features a large paddle switch that turns the lights on/off and returns them to your favorite preset setting, along with a discreet slider that brightens or dims the lights to suit any activity.

Create the perfect amount of light while utilizing the latest energy-saving technology with the Lutron Diva C•L Dimmer. Designed for use with 150-watt dimmable CFL or LED lights, the Lutron Diva C•L dimmer features a large paddle switch that automatically returns to your favorite pre-selected light level, a discreet slider to adjust light levels, and a sleek, modern wallplate.

Diva C•L Dimmer At a Glance: Dimmer works with most dimmable CFL/LED bulbs, as well as incandescent and halogen bulbs Slider for precise light control and paddle switch for easy on/off HED technology improves the performance of dimmable CFLs and LEDs over standard dimmers Adjustment dial to set bottom of dimming range for your bulb type Single-pole and three-way applications One-year limited warranty; UL-listed for a broad range of dimmable CFL/LED bulbs

Adjustment dial fine tunes dimming range for your specific bulb.

The C•L Dimmer works with a combination of CFL, LED, halogen, and incandescent bulbs and can be used on the same circuit.

Precise Light Adjustment with Slider

Whether you're reading, watching TV, entertaining, or enjoying a romantic dinner, the Lutron Diva C•L Dimmer lets you choose the right level of light for your activity. It's easy to make subtle adjustments using the discreet slider next to the large paddle switch. When you use the paddle switch to turn lights off and on, it defaults to your preferred lighting level.

Works with Dimmable CFLs and LEDs for Increased Energy Savings

The Lutron dimmer works with dimmable CFLs and LEDs up to 150 watts, a great energy-efficient alternative that can last up to 10 times longer than incandescent bulbs. Plus, by using less electricity, theses bulbs help protect the environment by reducing the amount of carbon dioxide released into the air.

HED Technology for Enhanced Performance

Thanks to Lutron's HED technology, this dimmer actually improves the performance of dimmable CFLs and LEDs compared to standard dimmers by eliminating flicker, ensuring lights stay on when they are dimmed to a low level, and making sure lights operate properly at all levels. Lights will stay on even during voltage fluctuations, which can happen when a device like an air conditioner or a hair dryer is operated nearby. For safety, the dimmer is UL listed for a broad range of dimmable CFL and LED bulbs.

Compatible with Other Lightbulbs and Mixed Loads

For added functionality, the dimmer also provides full-range dimming for halogen and incandescent bulbs. There is an adjustment dial to set the low end of dimming range for your bulb type for most efficient operation.

The dimmer also works with a mixed load of light sources, so a combination of CFL, LED, halogen, and incandescent bulbs can be used on the same circuit. It can be used for single-pole and three-way applications.

Fast and Easy Installation

Installation is easy--just replace your existing light switch with the Lutron Diva C•L Dimmer and install in less that 15 minutes. A modern wallplate--with no visible screws--blends into the surrounding wall for a subtle finishing touch.

The Lutron Diva C•L Dimmer is backed by a one-year limited warranty.

What's in the Box

Dimmer and screwless wallplate.

Set the perfect mood lighting for any room with the Diva C•L Dimmer.

From the Manufacturer

Control the next generation of lighting with Lutron's dimmable C.L dimmers! Screw-in dimmable compact fluorescent lamps (CFLs) and screw-in dimmable light emitting diode lamps (LEDs) are a great energy-saving alternative to incandescent or halogen light sources; however, dimming them may be difficult. Lutron's new dimmers with HED Technology provides a solution to alleviate your dimmable CFL and LED dimming challenges, while setting the right light level to improve mood and ambiance. The Diva dimmable CFL/LED dimmer with HED Technology features advanced dimming circuitry that is designed for compatibility with most high efficacy light bulbs. With the same features as Lutron's Diva dimmer, the large paddle switch turns the light on/off and returns to your favorite setting. The discreet slider adjusts the light level to suit any activity. These dimmers improve the dimming performance of dimmable CFLs and LEDs compared to standard dimmers. Lutron dimmers with HED Technology also provide full-range dimming for halogen and incandescent bulbs, ensuring today's dimmer is compatible with tomorrow's light sources. The dimmer can even dim a mixed load of light sources (i.e. LED and halogen or CFL and LED bulbs on the same circuit).

• Provides the best dimming performance for LED bulbs(for list of approved LEDs, see 'Technical Specification' below)
• For use with up to 150-Watts of dimmable LEDs or up to 600-Watts of Incandescent or Halogen bulbs
• Features a large rocker paddle to turn lights on/off or to preset level and a discreet slider to brighten/dim lights to suit any activity
• Can be used in single-pole or 3-way applications
• Installs in as little as 15 minutes. Operating temperatures 32 °F to 104 °F (0 °C to 40 °C)
• Includes Diva LED+ (formerly C.L) Dimmer Switch and coordinating wallplate

Product features

Lutron LED+ Dimmers provide over 250 lighting levels, so you can set the right light for any activity

• Large paddle switch to turn lights ON/OFF
• Sleek slider on the side to manually dim or brighten lights
• Technology that allows for smooth dimming of the broadest range of LEDs
• Patented technology to optimize the dim range of your bulb and prevent interference with other dimmers in the home
• Tried and true aesthetic to match designer/decorator style switches and accessories

Cutting Edge Technology

Our easy-to-set adjustment lever allows you to change the low end of dimming and set the optimum dim range for your bulbs.

Control up to 17 Bulbs

Each Lutron LED+ Dimmer can control up to 17 bulbs, and is the only dimmer UL listed to control mixed loads (different types of bulbs, such as LEDs and halogens, on the same circuit)

Blend In or Stand Out

Available in 25 colors so you can choose a finishing touch to your room that seamlessly blends in or a color that is meant to pop

Works Well with LEDs

Tested on 1,000’s of bulbs and dozens of brands to ensure flawless dimming. Check out our website for our list of recommended bulbs

Product description

The Leviton toggle slide universal dimmer provides smooth, slide-action, full-range dimming for dimmable leds, dimmable CFLs, incandescent and halogen bulbs. For a traditional home, the classic style offers the ideal way to upgrade the functionality without compromising the character of the decor.

• Classic design with toggle switch and integrated linear Full Range slide control for easy, precise operation
• Designed specifically for dimmable LED and CFL bulbs; also compatible with incandescent and halogen bulbs
• Single pole or 3 way capable when used with a 3 way switch
• Built in starting technology for CFL bulbs; Allows users to modify dimming range to optimize low light level performance when required (optional)
• Wider dimming range for LED and CFL bulbs than traditional incandescent dimmers

User questions & answers

Question:	Will this dimmer stand 12 AR111 12Watts each
Answer:	Dimmer will control 300 watt dimmable LEDs if the AR111s you have are dimmable 120V 12Watt lights then switch should be OK as 12 lights would be ~144 Watts
Question:	We were trying to connect this switch, the light is on but the dimmer is not working, its a single pole, what am I missing
Answer:	You need to be using "dimmable" bulbs, either incandescent or LED, but not fluorescent. If you are using dimmable incandescent or LED bulbs, I believe there is a slider control (switch) somewhere on this switch to choose either incandescent or LED. That needs to match your bulb type.
Question:	I installed the switch as well as dimmable led bulbs. they work on the dim setting but they blink from half all the way to full power, any ideas
Answer:	I've had similar issues and took it up with Leviton on their website. They initially just asked me to send it back to them, but I stopped short stating that I didn't particularly want to "finance" that. So they did send me a replacement unit and a prepaid shipping label. The replacement one is "better", but sometimes it still goes into flicker or as I call it "spazz" mode. They have asked me for the exact bulbs I'm using (Ecosmart Classic Glass Bulbs from Home Depot) but nothing further from them. I use those same bulbs in (2) other fixtures with Lutron LED dimmers (Model# TGCL-153PH-WH and Model# CTCL-153PR-WH) and they both have worked flawlessly for about a year. Never a single flicker. Bob
Question:	Where is the locator light
Answer:	Mine has a green LED at the top of the toggle switch. It is almost impossible to see in the light, but when the room is dark, it is visible without being disturbing. It comes defaulted to OFF. There are two micro switches on the front of the switch, which are hidden once that switch plate is put on. The top switch has an A and B position. A (the default) is for LED and incandescent lights. B is for CFC bulbs. A second switch, lower down, is for the locator light. Set the switch to ON if you want to use the light. Set these switches before you put on the switch plate because the plate covers these switches.

Product features

Leviton TSL06-1LT Toggle Slide Universal Dimmer

Leviton’s TSL06 Toggle Slide universal dimmer is engineered to provide homeowners optimal control of 300-watt Dimmable LED and CFL bulbs, and 600-watt Incandescent and Halogen bulbs. This new dimmer offers the energy-saving benefits of dimming without sacrificing performance or the time-honored design valued in traditional homes. The Toggle Slide universal dimmer addresses performance issues–such as flickering, reduced dimming range, and low level start up–often experienced when incandescent-only dimmers are paired with dimmable LED or CFL bulbs.

Great Dimming, Traditional Style

The Toggle Slide universal dimmer features an on/off preset function which preserves the selected dimmer setting, smooth start-up, gentle-touch control, and fluid slide movement for precise dimming. The device’s traditional aesthetics offer the ideal way to upgrade functionality from standard switches without compromising the character of your traditional decor. Its slim, compact housing fits easily into a standard wall box and is suitable for multi-gang installations. The Toggle Slide universal dimmer is compatible with Leviton’s complete line of signature Decora wiring devices and wall plates.

Advanced Features

The Leviton Toggle Slide universal dimmer features a microprocessor control which offers the flexibility to fine-tune LED and CFL bulbs for best performance. A “kick-start” setting is available to ensure start-up of CFL bulbs. The dimmer also features a soft green LED locator light built into the switch, making it easy to find in a dark room.

About Leviton Dimmers

Leviton is a leading manufacturer of dimmers designed for both the energy-saving benefits of dimming and the ambiance that can be created in any room of the home by controlling lighting levels. To ensure superior performance, Leviton works with bulb manufacturers to develop dimmers that are tested and proven effective to function in harmony with the latest bulb innovations. Leviton dimmers come in a wide range of models including digital, wireless, preset, slide, rotary, toggle, and touch and provide precise dependable control.

• Support single pole or 3-way applications, decor wall plate included. Only one dimmer switch can be installed per 3 way circuit
• LED Dimmer Light Switch: Provides the best dimming performance for LED bulbs. Simple and elegant horizontal slider dims and brightens with ease for full range light control
• Adjuster Dial: Ensures compatibility with almost all dimmable LED, CFL, incandescent and halogen bulbs, up to 150 watts of dimmable LED/CFL lamps or 600 watts of incandescent bulbs
• Smart Rocker: On/Off rocker switch remembers the last dimmed light setting and turns on to that exact light level
• 3 year warranty. UL listed. NOTE: The dimming range of dimmable LEDs may vary from manufacturer to manufacturer. This dimmer has an adjustable dimming range. Please rotate the side adjustment wheel to eliminate flicker issues

User questions & answers

Question:	are these ul listed
Answer:	Dear Customer, Thanks for your enquiry on BESTTEN Dimmer Switch. Yes, they are UL listed. You can also reach us via [email protected] or 800-358-6160 BESTTEN Customer Care
Question:	I am replacing incandescent dimmer switches these led switches are 2.12 inches wide. my existing switches are 1.75 inches wide. can they be trimmed
Answer:	Dear Customer, Thanks for your enquiry on BESTTEN Dimmer Switch. The side tabs can be removed which will reduce the width to 1.75in. Any other question, please contact us via [email protected] or call 800-358-6160. BESTTEN Customer Care
Question:	Do they come in light almond
Answer:	Don't think so.
Question:	Can we use these dimmers with leds that requires 0-10v dimming control (driver) 120-277v
Answer:	Dear Customer, Thanks for your enquiry on BESTTEN dimmer light switch. Yes, it can install in a 120v circuit and control a 0-10v dimmable LED lights. BESTTEN Customer Care [email protected]

Product features

BESTTEN Modern Dimmer Switch

BESTTEN dimmer switch provides smooth, sliding and full-range dimming performance for dimmable LED, CFL, halogen and incandescent bulbs. The slider can dim and brighten your lights precisely and conveniently, creating a romantic mood or a casual atmosphere for family activities.

• Single pole or 3-way
• No neutral required
• Large ON/OFF rocker paddle switch
• Precise full-range dimming control
• Wide range of compatibility with sensitivity dial
• Wallplate included

Specifications

Voltage.....................................................................................................120V, 60Hz

Dimmable LED/CFL................................................................................Max. 150W

Incandescent/Halogen.............................................................................Max. 600W

Switch Type.............................................................................................Single Pole/3-Way

Wiring Type..............................................................................................Wire Pigtails

Operation Temperature...........................................................................32°F (0°C) --- 104°F (40°C)

Remind:

One circuit can ONLY install one dimmer switch.

Troubleshooting

Symptom:

- Bulbs turn off while being dimmed.

- Bulbs turn on at high light level but do not turn on at a low light level, or take too long to turn on at low end.

- Bulbs flicker or flash when dimmed do a low light level.

- Bulbs or dimmers are buzzing.

Solution:

1. Verify all bulbs are marked dimmable.

2. Remove wallplate and locate sensitivity dial.

3. Turn up (counter-clockwise) sensitivity dial slowly until symptom is no longer present.

Product description

About the Lutron TTCL 100H BL Lamp Dimmer Plug In Credenza Incandescent/CFL LED Single Pole 250W/100W Black You don't necessarily have to install an in wall dimming device in order to be able to dim your lights to the perfect setting! With the black variety of the Lutron TTCL 100H BL Lamp Dimmer Plug In Credenza Incandescent/CFL LED Single Pole 250W/100W, you can take advantage of the lighting options and conveniences that come along with having a dimmer installed in your wall. This product is perfect for those people who don't want to install a dimmer in the wall or simply can't because they rent their living space. All you need to do to use the Lutron TTCL 100H BL 300W 250W/100W Credenza Incandescent/CFL LED Single Pole Plug In Lamp Dimmer is plug it into the outlet! The dimmer features a slider that gives you the ability to set your lights to the perfect level with ease and accuracy. The Lutron TTCL 100H BL 300W 250W/100W Credenza Incandescent/CFL LED Single Pole Plug In Lamp Dimmer also features an LED light, which gives you a built in nightlight to help you safely navigate the dark rooms of your home. The black color of the dimmer will make it unobtrusive and sleek, allowing you to add it to any lamp already in your home without it being an eyesore.

From the Manufacturer

Control the next generation of lighting with Lutron's dimmable C.L dimmers! Screw-in dimmable compact fluorescent lamps (CFLs) and screw-in dimmable light emitting diode lamps (LEDs) are a great energy-saving alternative to incandescent or halogen light sources; however, dimming them may be difficult. Lutron's new dimmers with HED Technology provides a solution to alleviate your dimmable CFL and LED dimming challenges, while setting the right light level to improve mood and ambiance. The Credenza dimmable CFL/LED lamp dimmer with HED Technology features advanced dimming circuitry that is designed for compatibility with most high efficacy light bulbs. Simply plug-in your table or floor lamp with the Credenza and start dimming! Use the slide to turn the light on/off or up to brighten and down to dim. Lutron dimmers with HED Technology also provide full-range dimming for halogen and incandescent bulbs, ensuring today's dimmer is compatible with tomorrow's light sources.

• For use with up to 100-Watt of most dimmable CFL/LED bulbs (please see specifications for a list of compatible bulbs)
• Also controls up to 250-Watt of incandescent and halogen bulbs
• Requires no wiring, just plug-in
• Slide to turn the light on/off or up to brighten and down to dim
• Easy plug-in installation

User questions & answers

Question:	Bistro: I just ordered bistro lighting for my balcony but the bulbs are not bright. Would this work for the bistro lights
Answer:	This product is rated to handle 100 watts of LED and CFL or 250 watts of incandescent and halogen line voltage lighting loads. As long as the Bistro lights fit these specifications and are not low voltage with a transformer, then this dimmer should be able to control them.
Question:	What is the Length of the cord?? Thank you
Answer:	Sorry but Barb tasted vacation and never came home...
Question:	Description says it supports 600 watts of incandescent, but some state only 250 or 300 watts. Can someone look on the back of their unit and confirm
Answer:	The model you specified (Lutron TTCL-100H-WH) will handle 250 W incandescent or 100 W CFL/LED bulbs as shown on the back of the unit.
Question:	Can someone confirm that this will turn off led bulbs completely? led, not incandescent
Answer:	Yes, if the LED can be dimmed. This is a very smooth operating dimmer. When you slide it to the lowest brilliance of the LED, the slide encounters the very slightest barrier which you have to push a bit further to actually turn off the bulb. If you don't slide to the very end, the LED just remains at very low brilliance!
Question:	Where is it made? USA
Answer:	HI，Customer， It is Made in China, UL listed
Question:	Are there a 2, 3 snd 4 gang wall plates for these
Answer:	Yes, these are standard size switches. Home Depot or Lowes should have multi-gang plates.
Question:	installed but not turning on when the slide is in between and also hear some sound when you keep your ears on switch in dim mode . anyone else faced
Answer:	No sounds from mine. Make sure your bulbs a dimmable type? Just a guess.
Question:	can this dimmer be used on 12 volt LED lamps
Answer:	I doubt it, but contact mfg., they are very responsive.

Product features

SINGLE POLE/3-WAY CIRCUIT INSTALLATION

• Single Pole: Connect the green dimmer ground wire to ground wire in the wall-box, Connect the black dimmer wire to the hot input wire removed from the switch,Connect either of the 2 red dimmer wires to the light fixture wire removed from the switch,Use wire nut to cap the remaining red wire on dimmer
• 3-Way: Connect the green dimmer ground wire to the ground wire in the wall-box, Connect the black dimmer wire to the TAG wire removed from the switch, Connect the red dimmer wires to the remaining wires removed from the switch

Manual Control

At the low end of the dimming level when the light starts to flicker, fine tune the dimming performance by turning the adjustment dial counter-clockwise so that the light output is stable. Set your slider to where there's no hum or flickering on light fixtures.

Screw-free wall plate

Install the dimmer and mounting frame with the tabs facing down. Put on the screw-free wall plate after tuning the adjustment dial.

Compatible with CFL/LED

Cloudy Bay dimmer improves the compatibility of dimmable CFLs and LEDs compared to standard dimmers by eliminating flicker, making sure lights operate properly at all levels.

Trouble shooting

1: Light flash in the whole dimming range

a. Check the lighting/lamp is dimmable or not

b. The lighting fixture is not compatible with our dimmer

c. Most dimmable LEDs and CFLs will not acheive as low level as incandescent or halogen sources.

d. Control a group of lighting fixtures/lamps with one dimmer may cause flicker due to variation of dimming circuit and dimming range. Please use dimmer to

control lights/lamps in the same type or same model.

2. Light flash in low dimming range

a.Slightly turn the adjustment dial counter- clockwise to achieve full compatibility with the lights

3. Get dimmer list from light bulb/lighting fixture's supplier to avoid compatible issue with our dimmer, a broad dimmer list means less dimming issue, such as flicker,buzz, or flash issue, also, better buy FCC compliance lighting product for stable performance.

Product description

The Leviton toggle slide universal dimmer provides smooth, slide-action, full-range dimming for dimmable LEDs, dimmable CFLs, incandescent and halogen bulbs. For a traditional home, the classic style offers the ideal way to upgrade the functionality without compromising the character of the decor.

• Classic design with toggle switch and integrated linear full-range slide control for easy, precise operation
• Designed specifically for dimmable LED and CFL bulbs; Also compatible with incandescent and halogen bulbs
• Single pole or 3 way capable when used with a 3 way switch. No removal of fins required for multi-gang installations
• Built-in starting technology for CFL bulbs; Allows users to modify the dimming range to optimize low light level performance when required (optional)
• Wider dimming range for LED and CFL bulbs than traditional incandescent dimmers

User questions & answers

Question:	Will this dimmer stand 12 AR111 12Watts each
Answer:	Dimmer will control 300 watt dimmable LEDs if the AR111s you have are dimmable 120V 12Watt lights then switch should be OK as 12 lights would be ~144 Watts
Question:	We were trying to connect this switch, the light is on but the dimmer is not working, its a single pole, what am I missing
Answer:	You need to be using "dimmable" bulbs, either incandescent or LED, but not fluorescent. If you are using dimmable incandescent or LED bulbs, I believe there is a slider control (switch) somewhere on this switch to choose either incandescent or LED. That needs to match your bulb type.
Question:	I installed the switch as well as dimmable led bulbs. they work on the dim setting but they blink from half all the way to full power, any ideas
Answer:	I've had similar issues and took it up with Leviton on their website. They initially just asked me to send it back to them, but I stopped short stating that I didn't particularly want to "finance" that. So they did send me a replacement unit and a prepaid shipping label. The replacement one is "better", but sometimes it still goes into flicker or as I call it "spazz" mode. They have asked me for the exact bulbs I'm using (Ecosmart Classic Glass Bulbs from Home Depot) but nothing further from them. I use those same bulbs in (2) other fixtures with Lutron LED dimmers (Model# TGCL-153PH-WH and Model# CTCL-153PR-WH) and they both have worked flawlessly for about a year. Never a single flicker. Bob
Question:	Where is the locator light
Answer:	Mine has a green LED at the top of the toggle switch. It is almost impossible to see in the light, but when the room is dark, it is visible without being disturbing. It comes defaulted to OFF. There are two micro switches on the front of the switch, which are hidden once that switch plate is put on. The top switch has an A and B position. A (the default) is for LED and incandescent lights. B is for CFC bulbs. A second switch, lower down, is for the locator light. Set the switch to ON if you want to use the light. Set these switches before you put on the switch plate because the plate covers these switches.

Product features

Leviton TSL06-1LW Toggle Slide Universal Dimmer

Leviton’s TSL06 Toggle Slide universal dimmer is engineered to provide homeowners optimal control of 300-watt Dimmable LED and CFL bulbs, and 600-watt Incandescent and Halogen bulbs. This new dimmer offers the energy-saving benefits of dimming without sacrificing performance or the time-honored design valued in traditional homes. The Toggle Slide universal dimmer addresses performance issues–such as flickering, reduced dimming range, and low level start up–often experienced when incandescent-only dimmers are paired with dimmable LED or CFL bulbs.

Great Dimming, Traditional Style

The Toggle Slide universal dimmer features an on/off preset function which preserves the selected dimmer setting, smooth start-up, gentle-touch control, and fluid slide movement for precise dimming. The device’s traditional aesthetics offer the ideal way to upgrade functionality from standard switches without compromising the character of your traditional decor. Its slim, compact housing fits easily into a standard wall box and is suitable for multi-gang installations. The Toggle Slide universal dimmer is compatible with Leviton’s complete line of signature Decora wiring devices and wall plates.

Advanced Features

The Leviton Toggle Slide universal dimmer features a microprocessor control which offers the flexibility to fine-tune LED and CFL bulbs for best performance. A “kick-start” setting is available to ensure start-up of CFL bulbs. The dimmer also features a soft green LED locator light built into the switch, making it easy to find in a dark room.

About Leviton Dimmers

Leviton is a leading manufacturer of dimmers designed for both the energy-saving benefits of dimming and the ambiance that can be created in any room of the home by controlling lighting levels. To ensure superior performance, Leviton works with bulb manufacturers to develop dimmers that are tested and proven effective to function in harmony with the latest bulb innovations. Leviton dimmers come in a wide range of models including digital, wireless, preset, slide, rotary, toggle, and touch and provide precise dependable control.

Product description

Control the next generation of lighting with Lutron's dimmable LED+ dimmers! Screw-in dimmable compact fluorescent lamps (CFLs) and screw-in dimmable light emitting diode lamps (LEDs) are a great energy-saving alternative to incandescent or halogen light sources; however, dimming them may be difficult. Lutron's new line of LED+ dimmers provides a solution to alleviate your dimmable CFL and LED dimming challenges, while allowing you to adjust the light level to improve mood and ambiance. with the same features as the original slide dimmer by Lutron, this Skylark dimmable CFL/LED dimmer features an easy to use slide control that adjusts the light to suit any activity, and a convenient switch that returns light to your favorite level. These dimmers still provide full-range dimming for halogen and incandescent bulbs, ensuring today's dimmer is compatible with tomorrow's light sources. The dimmer can even dim a mixed load of light sources (i.e. LED and halogen or CFL and LED bulbson the same circuit). Claro wallplate is not included.

• Tested on 1,000s of bulbs and dozens of brands for flicker-free dimming. For list of recommended bulbs view Technical Specification
• Provides over 250 lighting levels so you can create the perfect light for any activity
• Works with up to 150 Watts of dimmable LED/CFL bulbsor 600 Watts of Incandescent/Halogen bulbs
• Lutron patented technology to optimize the dim range of your bulbs and prevent interference with other dimmers in the home
• Can be used in single-pole or 3-Way applications, where lights are controlled from one or two locations
• Rocker switch turns lights on/off to favorite light level. Discreet slider dims and brightens the lights
• Includes Skylark LED+ (formerly C.L) Dimmer Switch; coordinating wallplate sold separately

User questions & answers

Question:	How do I wire this with no ground
Answer:	Note 4 of the installation instructions states: When no "grounding means" exist in wallbox, the 2011 NEC allows a control to be installed as a replacement if 1) a nonmetallic ,noncombustible faceplate is used with nonmetallic attachment screws or 2) the circuit is protected by a GFCI. When installing a control according to these methods, cap or remove green wire before screwing control into wallbox.
Question:	So I have two can light led’s wired to a 2 toggle switch plate, can I remove the light receptacle and replace with this to dim the lights
Answer:	As long as the LEDs you are using are compatible with this dimmer, then yes it will work properly for your application. For more information on compatible LED lamps, Lutron would reccomed checking out their LED tool at Lutron.com/ledfinder.
Question:	Can i use 2 of these to dim from either location on a 3way (currently an old skylark and an on/off switch)? or do i need a maestro setup
Answer:	On 3-way circuits, only one ELECTRO-MECHANICAL switch can be a dimmer regardless of lamp type, other switch must be standard single-pole 3-way on/off. You CAN use DIGITAL ELECTRONIC CONTROL SYSTEM (ie: MAESTRO) for all switches on circuit. Skylark SCL-153P dimmer is "electronic" but it is not a CONTROL SYSTEM that encompasses the whole circuit.
Question:	Can this dim incandescent and LED bulbs on the same circuit
Answer:	Yes- the issue is that the bulbs are very different and as a result will not dim uniformly so when dimmed one may be brighter

Product features

Cutting Edge Technology

Our patented easy-to-set adjustment lever allows you to change the low end of dimming and set the optimum dim range for your bulbs.

Control up to 17 Bulbs

Each Lutron LED+ Dimmer can control up to 17 bulbs, and is the only dimmer UL listed to control mixed loads (different types of bulbs, such as LEDs and halogens, on the same circuit)

Fast and Easy Installation

All you need to replace your existing switch or dimmer is about 15 minutes, 3 simple steps and 1 screwdriver

Works Well with LEDs

Tested on 1,000s of bulbs and dozens of brands to ensure flawless dimming. Check out the Lutron website for our list of recommended bulbs.

Product description

TOPGREENER Table Top Dimmer Easy installation, one-step set up, led compatible, instant results From TOPGREENER One of 's highest rated sellers and brand nationwide 150 Watt LED Support Full range support of all LED's for up to 150 watts 360 Watt Incandescent and Halogen Support Full range support of all Incandescent and Halogen for up to 360 watts of power Matte Finish Enhances grip and doesn't leave smudges or fingerprints Rubber Grib Bottom Keeps dimmer from sliding on any surface What's in the box Table-Top Dimmer Installation Instructions Product Description TOPGREENER Lamp Dimmer: 120 V, 60 Hz, 360 Watt Incandescent and Halogen, 150 Watt Dimmable LED, for Incandescent/Halogen Lamp, for LED lamp, Table-Top, Plug and Play, Plug-In Mounting, No programming required, 6 foot cable, heat resistant, impact resistant, Gloss White, Made of Thermoplastic, ETL Listed, for bedrooms, kitchens, dining rooms/living rooms, Lava lamps, turns off lights at lowest setting, will work with 3-way light bulbs, pre-lit Christmas trees, Christmas lighting, acts as On/Off switch. The TOPGREENER Plug-In Lamp Dimmer is a convenient dimmer for floor and table lamps. The lamp dimmer makes it easy to turn lights on and without the complications of wiring or hiring electricians to replace new switches with dimmers. The slider is smooth on contact and utilizes even smoother bright and lows when customizing the lighting to your desired level. The dimmer works with dimmable LED, Halogen and Incandescent lighting. Works with lava lamps, Christmas lighting, and any other lighting so long as wattage is not exceeded. For family rooms, bedrooms, offices, kitchens and more.

• Plug-in dimmer features full range dimming with a quiet slide control and no humming noise. Dim lights from 10% to 100%.
• Easy plug-in installation. No need to hire and electrician for wiring or programming
• Saves energy and extends bulb life by dimming lights. Compatible with 150 Watt LED and 360 Watt Incandescent and Halogen
• For use with floor lamps, table lamps, lava lamps and season lighting that do not exceed the specified wattage; NOTE: Not compatible with motorized devices, transformers or fans
• 120V, 60Hz rating, 2 Prong Plug, 6ft. Cord, fire resistant polycarbonate thermoplastic enclosure, ETL Listed

User questions & answers

Question:	Will this dimmer work with dimmable E26 Edison bulbs
Answer:	Hello, this is compatible with incandescent bulbs up to 360 Watts. So the Edison E26 at 60W would be compatible.
Question:	Does this dimmer work with a set of 3 plug in puck lights
Answer:	I hope this answers your question. I plug the lamp plug directly to the dimmer, then I take the dimmer plug and plug it into an electrical unit that has about eight plugins. Now, if your question is if there is 3 or 4 lights on a lamp and you are wondering if the dimmer will work on that certain light fixture the answer to that question is I do not know, but it should. I do not think it would work plugged into an extension cord with 3 or 4 different light fixtures attached to make all of them dim at the same time.
Question:	can it be used on a chandelier in the diningroom
Answer:	Only if your dining room chandelier is not hard-wired to a ceiling box. This dimmer is a LINE dimmer - that is to say, you plug your lamp into the cord’s outlet, and then plug this into the wall.
Question:	Can you use an extension cord with it
Answer:	My husband says that he thinks dimmer should be plugged directly into an outlet. But we’re not sure about this.

Product features

Topgreener Table-Top Dimmer

The Topgreener Plug-In Lamp Dimmer is a convenient dimmer for floor and table lamps. The lamp dimmer makes it easy to turn lights on and without the complications of wiring or hiring electricians to replace new switches with dimmers. The slider is smooth on contact and utilizes even smoother brights and lows when customizing the lighting to your desired level. The dimmer works with dimmable LED, Halogen and Incandescent lighting.

Dimmable String Lights

Dim down to 50% to increase the life span of light bulbs and save on energy.

Compatibility

Works with up to 150 Watts of LED or CFL or 360 Watts of Incandescent and Halogen.

Rubber Grip Back

Has four rubber grips on the back of the dimmer to secure to any surface.

Dimmable LED's

Dimmable Christmas Lights

Table and Floor Lamps

• 【VOICE CONTROL & 1%-100% DIMMING】This alexa smart plugs can adjust brightness level from 1-100% with Alexa and Google Assistant voice assistants, it can easily control outdoor lights by sending that voice commands like “Alexa, set my patio lights to 40%”.
• 【NO HUB REQUIRED & REMOTE CONTROL】The smart dimmer plug does not need to be connected to a cumbersome hub. Just simply plug in a device and you can control your outdoor smart plug via Smart Life APP directly from anywhere, as long as your phone access to a secure 2.4 GHz Wi-Fi network. (Note: Not support 5.0 GHz Wi-Fi).
• 【SCHEDULE & SUNRISE / SUNSET MODE】Create customized schedule or a lighting scene to automatically turn on/off. The outdoor dimmer supports sunrise and sunset setting, so you can program to turn on at dawn and off at dusk.
• 【CREATE GROUP &SHARE CONTROL】 By creating a group for all smart outlet, you can control combine wifi plugs in one command. Device sharing feature allows you to share the control with your family. Let you and your family enjoy the proper atmosphere in different occasions by adjusting the brightness at any time.
• 【WORRY-FREE SUPPORT】 IP44 waterproof, FCC certified. With ABS fireproof material, you can safely use this dimmer plug to light your outdoor string lights, bedside lamp or any party lights. Any unexpected quality issues, please contact us in time to activate your warranty service so as to get the best solution in the first time. Don't waste any of your money.

Product features

Control Outdoor and Indoor Lights from Anywhere

The smart dimmer lets you control all dimmer light bulb by your phone. 1% - 100% smart dimming range can adjust the ambiance of space better. From scheduling to creating scenes, the Smart Life APP puts you in control, wherever you are. Equipped with IP44 waterproof rating ensures keep the plug safe even when it’s rainy or near water.

This lamp dimmer also makes it so easy to turn on and off your bedside lamp especially in the middle of the night if you need to get up or have a low light on.

Product description

Bring technology and style to your home with the Caseta Wireless In-Wall Dimmer; the dimmer that is compatible with all of today's bulbs types, including dimmable CFL and LED, halogen and incandescent. The wireless dimmer gives you the ability to set the right light for any activity whether it's reading, watching TV, entertaining, or having a casual dinner. Conveniently control the dimmer with a Lurton Pico remote control, sold separately. Wall plate sold separately.

• PEACE OF MIND: Set lights to automatically adjust with seasons so your family always comes back to a well-lit home; Enable smart away to randomly turn your lights on/off to look like you’re home even if you’re away (smart bridge, L-BDG2-WH, required)
• MOST CONNECTED: Caseta connects with more leading smart home devices – including Alexa, Apple HomeKit, the Google Assistant, Ring, Serena shades and Sonos – than any other smart lighting control brand (smart bridge required)
• CONTROL YOUR WAY: Caseta puts the smarts in the switch so you can control a variety of ways – via the free Lutron app, your voice or from the wall; Schedule lights to change at set times or activate scenes with the touch of a button (bridge required)
• GET MORE, SPEND LESS: One Caseta smart switch can control many bulbs at once; Make many bulbs smart, even your existing bulbs. Get smart control of multiple styles of dimmable LED, incandescent, and halogen bulbs
• WORKS IN ANY HOME: Unlike other smart dimmer switches, Caseta works in any home, of any age, as it does not require a neutral wire
• WIRELESS REMOTE CONTROL: For added convenience, use with wireless Pico remote (PJ2-3BRL-GXX-L01) to turn your lights on, off, or dim and brighten with the touch of a button from anywhere in the home
• EASY 3-WAY SETUP: Create a 3-way by mounting Pico to almost any wall surface - no cutting holes or pulling wire, with a wall mount bracket (PICO-WBX-ADAPT sold separately). Replace existing 3-way switches by mounting the bracket and Pico over the backbox

• 3-Way Single Pole Compatible Slide control dimmer.Green indicator turns off when the load is on, turns on when the load if off.
• 600W max Incandescent; 150W max dimmable LED/CFL,120VAC, 60Hz*Fully compatible with Cloudy Bay LED light fixtures,600W max Incandescent,150W max Dimmable LED/CFL,120VAC,60Hz *Not compatible with smart lighting fixtures
• Works with LED,Halogen,Incandescent bulbs - Trim Dial below Cover Plate allows Sensitivity Adjustment upon installation to achieve compatibility with LED Lamps
• Decorative Wall Plate and Mounting Screws Included, easy to install.
• UL Listed,1 Year Warranty. Please contact us if there is any issue with dimming issue.

User questions & answers

Question:	With the switch on the dimmer works just fine. with the toggle switch off my led bulbs still glow slightly
Answer:	If you want to turn the light OFF, you must use the switch. The toggle will still give the lights some voltage even in the so called off position.
Question:	With the switch on the dimmer works just fine. with the toggle switch off my led bulbs still glow slightly
Answer:	Good

Product features

Dimmer Switch with Green Indicator

• Voltage: 120V AC
• Single Pole/3 Way installation.(please refer to brief wiring instruction below).
• Fine tune adjustment dial to eliminte LED/CFL flickering.
• No screws needed to fasten wall plate. Looks perfectly blend into the wall.
• Can be used with literally all kinds of your household lighting.
• Dimmer has been tested to be fully compatible with any light fixtures of Cloudy Bay Lighting family, including Cloudy Bay flush mount ceiling lights.
• NOT COMPATIBLE WITH SMART LIGHTS, SUCH AS GE C, PHILIPS HUE WHICH IS CONTROL BY WIFI, BLUE TEETH, ZIGBEE etc.

Compatible with CFL/LED/Incandescent

Cloudy Bay dimmer improves the compatibility of dimmable CFLs and LEDs compared to standard dimmers by eliminating flicker, making sure lights operate properly at all levels.

Tip: Most dimmable LEDs and CFLs will not acheive as low level as incandescent or halogen sources.

Fine tune with adjustment dial

At the low end of the dimming level when the light starts to flicker, fine tune the dimming performance by turning the adjustment dial counter-clockwise so that the light output is stable. Set your slider to where there's no hum or flickering on light fixtures.

SINGLE POLE/3-WAY CIRCUIT INSTALLATION

• Single Pole: Connect the green dimmer ground wire to ground wire in the wall-box, Connect the black dimmer wire to the hot input wire removed from the switch,Connect either of the 2 red dimmer wires to the light fixture wire removed from the switch,Use wire nut to cap the remaining red wire on dimmer
• 3-Way: Connect the green dimmer ground wire to the ground wire in the wall-box, Connect the black dimmer wire to the TAG wire removed from the switch, Connect the red dimmer wires to the remaining wires removed from the switch

Trouble shooting

1: Light flash in the whole dimming range

a. Check the lighting/lamp is dimmable or not

b. The lighting fixture is not compatible with our dimmer

c. Most dimmable LEDs and CFLs will not acheive as low level as incandescent or halogen sources.

d. Control a group of lighting fixtures/lamps with one dimmer may cause flicker due to variation of dimming circuit and dimming range. Please use dimmer to

control lights/lamps in the same type or same model.

2. Light flash in low dimming range

a. Slightly turn the adjustment dial counter- clockwise to achieve full compatibility with the lights.

3. Get dimmer list from light bulb/lighting fixture's supplier to avoid compatible issue with our dimmer, a broad dimmer list means less dimming issue, such as flicker,buzz, or flash issue, also, better buy FCC compliance lighting product for stable performance.