10 best ashley dimmer switches

• 3-Way Single Pole Compatible Slide control dimmer.If UP is off(DOWN is on) after wiring, try switching around the two red wires to reverse the on/off direction
• Fully compatible with Cloudy Bay LED light fixtures,600W max Incandescent,150W max Dimmable LED/CFL,120VAC,60Hz
• Works with LED,Halogen,Incandescent bulbs - Trim Dial below Cover Plate allows Sensitivity Adjustment upon installation to achieve compatibility with LED Lamps
• Decorative Wall Plate and Mounting Screws Included
• UL Listed,1 Year Warranty. Please contact us if there is any issue with dimming issue.

User questions & answers

Question:	Where is it made? USA
Answer:	No sounds from mine. Make sure your bulbs a dimmable type? Just a guess.
Question:	Are there a 2, 3 snd 4 gang wall plates for these
Answer:	I doubt it, but contact mfg., they are very responsive.
Question:	installed but not turning on when the slide is in between and also hear some sound when you keep your ears on switch in dim mode . anyone else faced
Answer:	Check the display is ON or OFF on the top left connor, it should show ON then the device can work.
Question:	can this dimmer be used on 12 volt LED lamps
Answer:	What I think was being asked is if this meter can tell you the PEAK load during the time it was connected. For example, let's say it was connected to a refrigerator for 10 hours. Let's say that during that 10 hours the load in Watts was 150Watts. But, when the compressor kicks in, it surges to 2000Watts for 3 seconds. Will this device allow you to see that 2000Watt PEAK later? Does it store that PEAK load into memory so you can view it?

Product features

SINGLE POLE/3-WAY CIRCUIT INSTALLATION

• Single Pole: Connect the green dimmer ground wire to ground wire in the wall-box, Connect the black dimmer wire to the hot input wire removed from the switch,Connect either of the 2 red dimmer wires to the light fixture wire removed from the switch,Use wire nut to cap the remaining red wire on dimmer
• 3-Way: Connect the green dimmer ground wire to the ground wire in the wall-box, Connect the black dimmer wire to the TAG wire removed from the switch, Connect the red dimmer wires to the remaining wires removed from the switch

Manual Control

At the low end of the dimming level when the light starts to flicker, fine tune the dimming performance by turning the adjustment dial counter-clockwise so that the light output is stable. Set your slider to where there's no hum or flickering on light fixtures.

Screw-free wall plate

Install the dimmer and mounting frame with the tabs facing down. Put on the screw-free wall plate after tuning the adjustment dial.

Compatible with CFL/LED

Cloudy Bay dimmer improves the compatibility of dimmable CFLs and LEDs compared to standard dimmers by eliminating flicker, making sure lights operate properly at all levels.

Trouble shooting

1: Light flash in the whole dimming range

a. Check the lighting/lamp is dimmable or not

b. The lighting fixture is not compatible with our dimmer

c. Most dimmable LEDs and CFLs will not acheive as low level as incandescent or halogen sources.

d. Control a group of lighting fixtures/lamps with one dimmer may cause flicker due to variation of dimming circuit and dimming range. Please use dimmer to

control lights/lamps in the same type or same model.

2. Light flash in low dimming range

a.Slightly turn the adjustment dial counter- clockwise to achieve full compatibility with the lights

3. Get dimmer list from light bulb/lighting fixture's supplier to avoid compatible issue with our dimmer, a broad dimmer list means less dimming issue, such as flicker,buzz, or flash issue, also, better buy FCC compliance lighting product for stable performance.

Product description

Leviton TSL06-1LW Toggle Slide Universal Dimmer, 300-Watt Dimmable LED and CFL, 600-Watt Incandescent and Halogen for Single Pole or 3-way, with locator light, White, Pack of 3

• Classic design with toggle switch and integrated linear full-range slide control for easy, precise operation
• Designed specifically for dimmable LED and CFL bulbs; Also compatible with incandescent and halogen bulbs
• Single pole or 3 way capable when used with a 3 way switch. No removal of fins required for multi-gang installations
• Built in starting technology for CFL bulbs; Allows users to modify dimming range to optimize low light level performance when required (optional)
• Wider dimming range for LED and CFL bulbs than traditional incandescent dimmers

• Support single pole or 3-way applications, decor wall plate included. Only one dimmer switch can be installed per 3 way circuit
• LED Dimmer Light Switch: Provides the best dimming performance for LED bulbs. Simple and elegant horizontal slider dims and brightens with ease for full range light control
• Adjuster Dial: Ensures compatibility with almost all dimmable LED, CFL, incandescent and halogen bulbs, up to 150 watts of dimmable LED/CFL lamps or 600 watts of incandescent bulbs
• Smart Rocker: On/Off rocker switch remembers the last dimmed light setting and turns on to that exact light level
• 3 year warranty. UL listed. NOTE: The dimming range of dimmable LEDs may vary from manufacturer to manufacturer. This dimmer has an adjustable dimming range. Please rotate the side adjustment wheel to eliminate flicker issues

User questions & answers

Question:	are these ul listed
Answer:	Dear Customer, Thanks for your enquiry on BESTTEN Dimmer Switch. Yes, they are UL listed. You can also reach us via [email protected] or 800-358-6160 BESTTEN Customer Care
Question:	I am replacing incandescent dimmer switches these led switches are 2.12 inches wide. my existing switches are 1.75 inches wide. can they be trimmed
Answer:	Dear Customer, Thanks for your enquiry on BESTTEN Dimmer Switch. The side tabs can be removed which will reduce the width to 1.75in. Any other question, please contact us via [email protected] or call 800-358-6160. BESTTEN Customer Care
Question:	Do they come in light almond
Answer:	Don't think so.
Question:	Can we use these dimmers with leds that requires 0-10v dimming control (driver) 120-277v
Answer:	Dear Customer, Thanks for your enquiry on BESTTEN dimmer light switch. Yes, it can install in a 120v circuit and control a 0-10v dimmable LED lights. BESTTEN Customer Care [email protected]

Product features

BESTTEN Modern Dimmer Switch

BESTTEN dimmer switch provides smooth, sliding and full-range dimming performance for dimmable LED, CFL, halogen and incandescent bulbs. The slider can dim and brighten your lights precisely and conveniently, creating a romantic mood or a casual atmosphere for family activities.

• Single pole or 3-way
• No neutral required
• Large ON/OFF rocker paddle switch
• Precise full-range dimming control
• Wide range of compatibility with sensitivity dial
• Wallplate included

Specifications

Voltage.....................................................................................................120V, 60Hz

Dimmable LED/CFL................................................................................Max. 150W

Incandescent/Halogen.............................................................................Max. 600W

Switch Type.............................................................................................Single Pole/3-Way

Wiring Type..............................................................................................Wire Pigtails

Operation Temperature...........................................................................32°F (0°C) --- 104°F (40°C)

Remind:

One circuit can ONLY install one dimmer switch.

Troubleshooting

Symptom:

- Bulbs turn off while being dimmed.

- Bulbs turn on at high light level but do not turn on at a low light level, or take too long to turn on at low end.

- Bulbs flicker or flash when dimmed do a low light level.

- Bulbs or dimmers are buzzing.

Solution:

1. Verify all bulbs are marked dimmable.

2. Remove wallplate and locate sensitivity dial.

3. Turn up (counter-clockwise) sensitivity dial slowly until symptom is no longer present.

• Support single pole or 3-way applications, decor wall plate included. Only one dimmer switch can be installed per 3 way circuit
• LED Dimmer Light Switch: Provides the best dimming performance for LED bulbs. Simple and elegant horizontal slider dims and brightens with ease for full range light control
• Adjuster Dial: Ensures compatibility with almost all dimmable LED, CFL, incandescent and halogen bulbs, up to 150 watts of dimmable LED/CFL lamps or 600 watts of incandescent bulbs
• Smart Rocker: On/Off rocker switch remembers the last dimmed light setting and turns on to that exact light level
• 3 year limited warranty. UL listed

User questions & answers

Question:	does this switch have circuitry does it operate without creating buzzing or humming sound
Answer:	Dear Customer, Thanks for your question about BESTTEN Dimmer Switch. The device will not create buzzing or humming sound. If there are any issues, please feel free to contact us via [email protected] Sincerely BESTTEN Customer
Question:	Do these match your Snow White wall plates
Answer:	Dear Customer, Thanks for your enquriy on BESTTEN dimmer switches. The products match our yellow-white wall plate best. You can refer to the below link: https://www.amazon.com/dp/B07BLXZMBX?ref=myi_title_dp You can also reach us via [email protected] or 800-358-6160 BESTTEN Customer Care
Question:	Does this switch stop led blinking
Answer:	Dear Customer, Thanks for your enquriy on BESTTEN Dimmer Light Switch. If your light flicker when it works with this dimner, you can follow the motheds on description or mannual to adjust the adjust wheel to avoid it. You can also reach us via [email protected] or 800-358-6160 BESTTEN Customer Care
Question:	I understand that there can only be 1 dim switch in a 3-way setup. Can one of these switches be wired so it is only on/off
Answer:	Your cheaper off putting a standard 3 way for the second switch.

Product features

BESTTEN Modern Dimmer Switch

BESTTEN dimmer switch provides smooth, sliding and full-range dimming performance for dimmable LED, CFL, halogen and incandescent bulbs. The slider can dim and brighten your lights precisely and conveniently, creating a romantic mood or a casual atmosphere for family activities.

• Single pole or 3-way
• No neutral required
• Large ON/OFF rocker paddle switch
• Precise full-range dimming control
• Wide range of compatibility with sensitivity dial
• Wallplate included

Specifications

Voltage.....................................................................................................120V, 60Hz

Dimmable LED/CFL................................................................................Max. 150W

Incandescent/Halogen.............................................................................Max. 600W

Switch Type.............................................................................................Single Pole/3-Way

Wiring Type..............................................................................................Wire Pigtails

Operation Temperature...........................................................................32°F (0°C) --- 104°F (40°C)

Remind:

One circuit can ONLY install one dimmer switch.

Troubleshooting

Symptom:

- Bulbs turn off while being dimmed.

- Bulbs turn on at high light level but do not turn on at a low light level, or take too long to turn on at low end.

- Bulbs flicker or flash when dimmed do a low light level.

- Bulbs or dimmers are buzzing.

Solution:

1. Verify all bulbs are marked dimmable.

2. Remove wallplate and locate sensitivity dial.

3. Turn up (counter-clockwise) sensitivity dial slowly until symptom is no longer present.

Product description

Lutron Credenza Plug In Dimmer for Halogen and Incandescent Bulbs, TT 300H WH, White.

From the Manufacturer

These lamp dimmers make it easy to turn lights on and off without reaching under the lamp shade. They feature LEDs that glow softly. Place dimmer on tabletop for easy operation.

• For use with 300 Watts of Halogen or Incandescent bulbs(for LED version, please see TTCL 100H WH)
• Dims table and floor lamps to suit any activity
• Easy plug in installation; no wiring required
• Easy slide operation allows you to adjust lights to desired level
• Cord included with product is 6 feet long
• Includes Credenza plug in dimmer

User questions & answers

Question:	Does this work with a lamp that has 3 way switch
Answer:	You ay need to click twice at the lamp itself to get it to work for either on or off. I know I need to do that on my 3 way lamp.
Question:	Please clarify, is this for on/off only or will it dim my lamp that I would plug into it
Answer:	is this for torch lamps
Question:	Where is the switch located? close to the outlet? in the middle of the cable
Answer:	The slider switch is in a 1" X 2" box at the end of a 3 foot cord. The unit is plugged into the wall outlet and the lamp is plugged into the back of the plug. You can run the cable for the dimmer switch alongside the lamp's cord, or in another direction entirely
Question:	would this work to regulate a 3000watt heating element
Answer:	You should never use an extension cord or similar item with a 3000 watt heating element. Great way to start a fire.

• Levven GoConex switches and controllers to control lights and other electrical loads without cutting holes and pulling wire inside the wall. Installs in minutes. Installation videos and instructions available
• MOUNT ANYWHERE - Switches mount on any surface – concrete, drywall, tile, wood, brick – without wiring, holes, switch boxes, or damage. Switches have an indoor range of 250 feet
• FLEXIBLE - Pair additional switches to the controller to do multi-way switching (3-way or 4-way switching) Works great with ceiling fans, lamps, LEDs, fixtures and other electronics.
• CUSTOMIZABLE: This set is dimmer controls but you can group load controllers to control many lights and circuits. Levven GoConex offers dimmer versions and different color switches as well
• BUILT TO LAST - Made in Canada Switch includes 3V CR2032 lithium button battery with 10 year+ battery life

User questions & answers

Question:	where is the battery for the switch part, it doesn't light up
Answer:	this is a PWM dimmer. work's great for led's
Question:	Do the switches fit a standard decora switch cover plate? Do I just add a new switch to a blank wall with double sided tape
Answer:	Yes it works just fine. All you need is a second switch that is SPDT and you wire the 'pole' sourcing from your + and the two 'pole' locations feed one to the dimmers red and the other to the 3way sw 1/p terminal. American Tech makes one - model AH-SWI-02-x where the X is 5 for black and 1 for white. wiring diagrams is at this link on the manufactures web site. https://www.atcomp.com/wp-content/uploads/2018/08/12V-3WAY-DIM.pdf Hope that helps folks
Question:	Does it work with low voltage under cabinet lighting
Answer:	A) If you have an existing switch: The two wires on the old switch are not really positive and negative. One is +12 volt power from the battery, and the other is going to the light. If you look inside the wall, you will likely find that each of the two coloured wires is paired with a white wire and those two white wires are connected together. Those white wires are the negative, and the place to connect the negative (neutral) wire from the new dimmer switch. After disconnecting the old switch, use a volt meter or a test light to determine which of the coloured wires is live - that will be the one coming from the battery. Connect that to the +12 volt side of the new dimmer. Connect the other coloured wire to the load side of the dimmer. B) If there is no existing switch, just a light: Disconnect the positive wire from the light and connect it to the +12v wire of the dimmer. Connect the negative wire of the dimmer to the existing negative wires of the light. Connect the load wire of the dimmer to the open positive wire of the light.
Question:	will they work with led can lights
Answer:	Press select key when turn on the power ..

• Easy Installation: The 3-way smart dimmer switches kit comes with one three-way master switch and one three-way add-on switch; Quick installation with step-by-step guide; Designed to control the lights from two locations; Also support 3 or more locations, 3/4/5/6-way circuit, with extra TESSAN add-on switch; Ideal for your bedroom, stairway and other large spaces; Standard size fit the regular 1/2/3/4 gang wall plate; Notice: Neutral wire is required for master switch
• Advanced 0-100% Dimming: Set the desired brightness from 0-100% to meet your ambience and cut down your bill; An adjustable dial built into the 3way master switch; Allows to adjust the minimum brightness of the lights; With Brightness memory function, the light will turn back to previous brightness after turned off; Support dimmable triac LEDs and dimmable CFLs max 150W, incandescent bulbs max 400W
• Hand-free Voice Control: TESSAN 3-way wifi dimmer switch compatible with Amazon Alexa and Google home; Simply give a command to dim/on/off the lighting instead of finding the switch; Make your hand-free smart home life more convenient and easier
• Remote Control with Timer and Schedule: Remote control the dimmable smart switch from everywhere; Program your private schedule, accessed lights will be dim/on/off at specified time; Schedule lighting to periodically turn on when not at home, it looks like someone is home when you leave; All TESSAN smart switches can be combined in one group, so you can dim/on/off different room lighting with one click; Support 2.4Ghz Wifi only, dual-band (2.4G and 5G) WiFi need to set a separate 2.4G channel
• Friendly Customer Service - TESSAN provides online installation assistance and life-time technical support directly; 18 months quality issues support; We will follow up and respond within 24 hours

User questions & answers

Question:	does the dimmer remember its setting when powered off
Answer:	I would estimate the lowest level be 10%-20%
Question:	Can this be used to control on off on a ceiling fan? Will the dimming control the speed
Answer:	Hello Rachel, There is no motion sensor with this dimmer switch, thanks and best wishes! Regards, Tessan Customer Care
Question:	What is the lowest % these will dim to
Answer:	HI，Customer， It is Made in China, UL listed
Question:	Does this switch have motion sensor
Answer:	Yes, these are standard size switches. Home Depot or Lowes should have multi-gang plates.

Product features

3-Way WiFi Dimmer Light Switch Kit

This smart dimmer would connects to your existing home Wi-Fi network easily to provide wireless control of your lights – with no hub or bridge required. You can easily set the ambiance of any room and control your lights from anywhere with Smart Life APP. Whether you're unwinding on the couch, meeting in the boardroom, or vacationing in Hawaii, you'll be able to remotely control and dim your home lighting from anywhere.

Specification:

Build your smart home with Smart Life app

This dimmer light switch would work with "Smart Life" App to control your room lights. Smart Life App is the most popular IOT App in the US at this moment, so you can hunt for different products that work well with the Smart Life app for your home automation.

Voice Commands Compatible with Alexa and Google Assistant

TESSAN dimmable smart light switch works seamlessly with Amazon Alexa and Google Assistant to give you hands-free voice control over your lights. It's so helpful when you back home with hands full of groceries.

Timer Switch and Automation

It's a timer dimmer switch, you can set automatic schedules for your light easily. Using the Smart Life app, you can schedule your hall lights to turn off at sunrise, or synchronize your living room lights with the sunset so you never come home to a dark house. Works with IFTTT to create applets according to your needs.

STEP 1: Install the Master Switch and Add-On Switch

-> Attach the white wire(neutral wire) from the master switch to the group of white wires (neutral wire) in the electric box.

-> Attach the black wire(live wire) from the master switch to the hot wire in the electric box.

-> Attach the TRA-2 wire(brown) from the Add-on switch and the load wire from the light bulb to the TRA-2 wire(brown) from the master switch.

-> Attach the TRA-1(red) wire from the Add-on switch to the TRA-1 wire(red) from the master switch.

-> Attach the ground wire(green) from the master switch to the group of ground wire, and Add-on switch is the same.

STEP 2: Check the Wiring is Correct

-> Check the led indicator of the master switch, when the green led Indicator flashes quickly, it means you have a wrong wiring, back to Step 1 to check and rewiring. if the red led indicator is always on, go to the next step.

-> Manually turn on/off and Dim/Brighten the switch, if the light bulb work well, the wiring is ok. if you can only turn on/off the light, but can't dim or brighten the lights normally, back to Step 1 to check and rewiring (usually is the wire to the light bulb have a wrong connection to TRA1, attach it to the TRA-2(master or add-on switch is ok) will slove the problem)

STEP 3: Connect the Smart Switch to Wifi

1> Login the "Smart Life - Smart Living" App with your account.

2> Click"+" in the top right corner of app to add the smart switch.

3> Click "Switch(Wi-Fi)" in Electrician Category.

4> Check the switch is in the pair mode, AP mode will be more stable when connect the switch to wifi

5> Follow the app instructions to complete the addition

STEP 4: Pair works with Alexa/Google home

->Pair works with Alexa

click"Skills" > search"Smart Life" app > click"enable" > Login with your smart life account (the same account that you pair with your switch) > click "Link now" > finished

->Pair with Google Home

>"Home Control" > Click "+" add a device > search "Smart life" app > Login with your smart life account (the same account that you pair with your switch) > click "Link now" > finished

The Wiring Diagram of TESSAN 3-Way Smart Dimmer Switch

Q1: Why the switch can't control the lights? or Why the switch can't turn on/off and dim/brighten the lights?

A: You have a wrong wiring, please back to step 1 to check and rewiring the switch, or you can mail our support team for further assistance, please note take a photo about the wiring of the old switch you replaced will be very useful for your installation.

Q2: Why the switch can't connect to wifi?

A: Kindly please check and follow the steps:

1> Check the Wiring follow the Wiring Diagram and STEP 1

2> Make sure your WiFi router on 2.4G Channel, no access limitation (like Static IP or MacAddress Bonding), set a different name for the two channel when the router is on 2.4G and 5G mixed mode, as "wifi 2.4g" and "wifi 5g".

3> Make sure your phone is on 2.4ghz channel When syncing with switch.

4> Installed the correct App named "Smart Life - Smart Living" or "Tuya Smart".

5> Use the AP mode will improve your success rate for the wifi connection.

6> Please check the number of devices connected to wifi router, When the number exceeds the performance of the router, the wifi connection would be unstable or failed. so you need pause or turn off some devices, For some old routers, keep the number of devices connected to the router less than 10 at the same time, it will improve your success rate for the wifi connection.

Q3: Why the switch can't connect works with Alexa/Google home?

A: -> Make sure your switch was installed correctly, add the switch in the "smart life" APP and be sure the switch works well with the smart life app.

-> Check the skill your enabled was correct (the same as the Smart Life App logo).

-> Verify that the account used in the skill is the same as in the Smart Life App (many people use another account).

Product description

Leviton Decora SureSlide dimmers provide smooth, slide-action, full-range dimming for incandescent and dimmable LED and CFL lamps. Featuring a pre-set On/Off switch, this device allows the user to set the desired brightness level to operate automatically with the On/Off function. The dimmer is designed specifically for dimmable light-emitting diodes (LED) and dimmable compact fluorescent (CFL) lamps; It is also compatible for use with incandescent lamps. Note: Flickering means that the bulb being used is not compatible with our device. In the technical specifications section, the application guide is a list of bulbs that Leviton has confirmed will work with our device. Kindly refer this guide for better use.

• Future proof to control a variety of dimmable CFL and LED lamps
• Integrated linear full range slide control for easy, precise operation
• Backwards compatible with incandescent lamps
• CFL mode for dimmable CFLs; This feature provides a higher starting voltage that is required for many compact fluorescent lamps
• LED/Incandescent mode provides optimized dimming for LED lamps and for incandescent operation
• See LED bulb compatibility in the technical specifications below (comparison chart PDF)
• Wallplate sold separately

User questions & answers

Question:	I plan on using this with a track lighting kit that uses dimmable leds. do i need anything (transformer?) between this switch and the track fixture
Answer:	It would depend on the rack light system you use. If it uses 120v lamps then no. if it is a lower voltage lamp system it would have its own transformer as part of its installation and this dimmer is probably not what you need. You would then want a dimmer designed for low voltage applications. As far as I know though there is no hard and fast rule on this today as all the dimmers and transformers are electronic and may or may not be compatible with other electronic devices including the led drivers fjord the particular lamps in the track system you select. You should consult with the dealer you ate purchasing from and the installing electrician. If you ate doing it yourself you'll need do your research through the manufacturers of the equipment for comparability like the electrician would.
Question:	What size bulb can be used with this dimmer? There seem to be all kinds of size bulbs available
Answer:	That's right in the description: 150 watts LED / CFL, 600 watts incandescent. Just add the power requirements of all the bulbs controlled by the dimmer. For example, I'm using it to control 4 60 watt incandescent bulbs, total 240 watts. For LEDs / CFLs, use the actual power required, not the "equivalency". So a 23-watt CFL that says it's as bright as a 100 watt incandescent still only counts as 23 watts.
Question:	difference in led and incandescent lighting dimmers
Answer:	Some incandescent dimmers modify the output of the power in such a way that it either won't work at all or can damage the LED dimmer. LED dimmers I believe use finer PCM (Pulse Code Modulation) which will work with all dimming bulbs - incandescent, CFL, and LED bulbs. Using LED bulbs with a non-LED dimmer is a bad thing as is using LEDs that are not designed to be dimmed at all. The payback for the additional expense of the LED dimmer is pretty quick if it removes a large enough incandescent light bulb.
Question:	Led dimmable bulb is flickering with this switch, is it bad
Answer:	Problem: Flickering or FlashingPossible Cause #1: Incorrect VoltageLED downlights have a specified input voltage. Incorrect voltage to the driver can cause the LED to flicker or toflash on and off. * Check the input voltage of the driver (Ex: 120V) then check the voltage being delivered to the fixture (Ex: 277V). There may be a mismatch. If possible, replace the driver on the downlight for one with the correct input voltage to match the line voltage or, if that is not an option, install an applicable voltage transformer to the line voltage to achieve the required input voltage for the original fixture.Possible Cause #2: Incompatible DimmerIf the LED downlight was not designed for a particular dimming load or if the driver is not compatible with thedimming control then issues may occur. * Try bypassing the dimming circuit. If the LED functions normally then an incompatible dimmer or dimming load may be the issue or the driver is not a dimming driver. Consult factory to determine whether the driver is dimmable and, if so, what kind of dimmer is compatible with the driver. Please check this web link for a list of factory qualified compatible dimmers: http://www.liton.com/webcatalog/brochures/wp_dimmingfacts.pdfPossible Cause #3: Occupancy Sensor/Control Rated WattageThese controls sometimes have a minimum rated wattage in order to function correctly. For example, theremaybe a minimum of 20W required for the control unit but the LED might only consume 10W. * Add additional fixtures to the circuit to get to the required wattage for the dimming control or replace the dimming control unit with one that has a lower wattage requirement.remedyremedyremedycontinue...TROUBLESHOOTINGLED DOWNLIGHTSA DIVISION OF EEMA LIGHTING GROUP * 5461 WEST JEFFERSON BLVD., LOS ANGELES, CALIFORNIA * PH: 323.904.0200 (1 800 515 4880)FAX: 323.904.0201 (1 800 972 4880)Problem: Flickering or Flashing cont..Possible Cause #4: Dimmer OverloadA common problem with LED dimming is the inadvertent overloading of the LED driver. LED drivers are rated fora maximum load (measured in volts, amps and/or watts) that must not be exceeded.The number of lamps that can be installed on a single-phase control dimmer may seem to be an easy calculation.For example, suppose you want to know how many 15W LED fixtures can be installed on a 600W dimmer. Youmight divide the 600W by 15W and determine that you could control 40 fixtures. Unfortunately, that result mightbe wrong. In fact, you may only be able to use 6 LED fixtures on a dimmer rated for 600W.Even though the LED fixture may draw only 15W continuously, there may be a start-up in-rush current or arepetitive half cycle surge that makes the dimmer think that the current is much higher. That 15W LED fixturemay appear to the dimmer as a 100W incandescent load. If that happens and you are using more than 6 LEDfixtures, you will overload the dimmer.The average start-up or half-cycle stress that has been observed is the equivalent of a 100W incandescent lamp,even for LED loads of less than 20W! * For 10W & 15W Liton -DLV products, consult the charts in the LED Dimming Facts Guide to reference tested maximums by dimmer. * Remove the dimmer from the line to see if the problem is solved. * Change dimmer to one with a higher maximum load. * Split the circuit into multiple loads.Possible Cause #5: Dimmer UnderloadSome dimmers may not perform well if too little load is put on them. A minimum number of fixtures may berequired to operate correctly due to the 25W - 40W minimum load that most incandescent dimmers require tooperate correctly under all conditions. When using incandescent bulbs, the minimum load requirement waseasily met. However, with LED four or more loads may be required for a dimmer to reach the required minimumload. * For 10W & 15W Liton - DLV products, consult the charts in the LED Dimming Facts Guide to reference tested minimum by dimmer. * Remove the dimmer from the line to see if the problem is solved. * Change dimmer to one with a lower minimum load.

Product features

Multiple Locations

Perfect in large areas or hallways/staircases that have two switches that control the same light(s).

Leviton Dimmers Put You In Control

Set the mood by adjusting the light level for any activity. Whether you are entertaining, reading, keeping the little ones safe from bedtime “monsters” or watching the latest flick, you're in control.

Superior Performance

Take advantage of the full dimming range of your bulb by adjusting the minimum light level on the dimmer.

Compatibility is Key

To achieve the best dimming performance, ensure that the bulbs are compatible. Download the “comparison chart” in the technical specification section below to see the best pairings for this dimmer.

• ETL listed dimmer switch for dimmable LED, CFL, halogen and incandescent bulb
• Works with 150 Watts dimmable LED/CFL or 600 Watts Incandescent/Halogen bulb
• Single pole and 3-way compatible
• Easy installation; wall plate and mounting screws are provided
• Excellent dimming performance; ideal for indoor and outdoor use

User questions & answers

Question:	Can i use 2 of these 3way dimmable switches for the same light? i read that i should use a 3way dimmable switch paired with a 3way non dimmable switch
Answer:	Hello, this is a normal dimmer switch to remote 12V lightings, can not remote fans.
Question:	This 3 way dimmable switch is supposed to be installed with a 3 way non-dimmable switch right? which non-dimmable switch is it compatible with
Answer:	I can't get it to work either. Also will need to return. I am surprised they do not give more information to prevent all the returns. I think ALL RV's only have 2 wires.
Question:	Will this work with a single low watt led as well as if i chained led bulbs
Answer:	I love the product but not sure they are rated for exterior use. I,m thinking that if you sealed the outside edges it should work fine.
Question:	What amperage does this dimmer have
Answer:	Your question could mean a couple different things. People often tie the "negative" or "return" black wire to ground, although that is generally bad practice. For sure you have to use the return wire or you otherwise don't have a circuit. Chances are high this does not have an independent ground built in, which is why we'll be seeing a lot more fires in the future.

Product description

Lumen, 150W, white, dimmer switch, LED/compact fluorescent light or 600W incandescent/Halon, single pole or 3 way preset dimmer, larger rocker switch turns lights on/off, slide up to brighten, down to dim, certified to dim the broadest ran of LED bulbs, can dim mixed load of light sources, crisp clean lines with classic aesthetic, longer slide for maximum dimming ran, clamshell. LECL-153P-WH-3

• LED/compact fluorescent light or 600 W incandescent/halon, single pole or 3 way preset dimmer, larger rocker switch turns lights on/off
• Slide up to brighten, down to dim, certified to dim the broadest ran of LED bulbs
• Can dim mixed load of light sources, crisp clean lines with classic aesthetic, longer slide for maximum dimming ran, clamshell

User questions & answers

Question:	The tabs on the right and left side of each switch do not allow enough space to fit into a three switch wall plate. How is this accomplished
Answer:	Bend the tabs back forth until they separate from the switch this allows the switches to fit in a 2 or 3 gang box leave the tabs on each switch that’s located on the both ends of box.
Question:	where is this product manufactured
Answer:	The ones I received were made in China.
Question:	What is the difference between this and the Skylark? Are they there same range
Answer:	They work well, don't know about Skylark, mine work well with dimmable LEDs and don't flicker at low setting.