9 best heating floorings

Product description

A gentle electric radiant heat system designed specifically for dry installation under floating wood and laminate floors. A low profile, line voltage system, it features gradual warmth from low wattage resistance heating of ultra-thin, flexible radiant heat film.Installed easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12 watts per square foot to gently raise the temperature of the floor, conforming to the warranty requirements of many floating floors. The system, which sports an impressive 99% efficiency, includes temperature limiting properties so the film does not overheat.APPROVED FLOOR COVERING MATERIALS • All Floating Floors • Floating Tiles • Laminate Flooring • Engineered Wood • Luxury Vinyl Flooring (4mm or thicker) • Cork and BambooRefer to Floor Covering Manufacturer's specifications for compatibility of their product over any radiant heat before installation.Its available in four convenient rollout mat sizes that will accommodate most any layout. Each mat has wires pre-attached for ease of installation.• Uses an highly-efficient conductive ink technology • Consumes up to 50% less power than traditional wired systems • Easy to install: roll out, cut length to fit if needed and run pre-attached wires to a wall thermostat • No mortar and no mess • Conforms to many floating floor manufacturers requirements • Disperses an evenly consistent heat throughout the entire floor

• easy installation - 3 simple step process (1. install underlayment, 2. roll out electric radiant heat film & 3. install final floor covering)
• " minimal thickness profile - ultra-thin (less than .016") heated panels keeps same floor heights through room transitions"
• provides uniform heat - your floor is heated uniformly with no gaps and the radiant heat is dispersed evenly through the room
• quiets your floor - used in combination with quiet walk underlayment, you achieve a superior sound rating: iic 71 & stc 67
• safety certified - etl in compliance with ul standards for radiant flooring in the usa and canada
• cost less to operate - even heat distribution allows the quiet warmth systems to cycle quicker resulting in less energy consumption
• maintenance free - crafted to not completely shut down if the system should ever become compromised or damaged
• mat size: 1.5 ft. x 5 ft. - 120v

User questions & answers

Question:	Do I need to buy a thermostat to control it? Or can it be connected to a switch? Just on and off
Answer:	Yes sensor included.
Question:	What underlayment is recommended for this heating film
Answer:	Yes, you are able to hook up two separate mats to one thermostat. You just cannot exceed a 15 AMP draw. Please reference the reading on your mats for this information. If you have any further questions, please let us know. Thank you for considering this product.
Question:	Planning 1 mat 1.5x5 = 90 watts. Can I use this w/o thermostat? Just on a gfci protected circuit w/ off/on switch
Answer:	Yes - you tell name each room and can control each independent.
Question:	Can these be cut and wired in a series to one thermostat
Answer:	Currently No! We are working on a newer version of this product that with have the smart-home capability.

Product features

QuietWarmth Radiant Heat Film for Floating Wood and Laminate Floors

Installs easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12 watts per square foot to gently raise the temperature of the floor. The system, which sports an impressive efficiency, includes temperature limiting properties so the film does not overheat. Its available in four convenient rollout mat sizes that will accommodate most any layout.

• Use with most floating laminate, engineered wood and floating tile floors
• Uses an highly-efficient conductive ink technology
• Disperses an evenly consistent heat throughout the entire floor
• Will not add extra height to the floor, only 0.016 in. thick
• Easy to install: roll out, cut length to fit if needed and run pre-attached wires to a wall thermostat
• No mortar and no mess
• Conforms to many floating floor manufacturers requirements

Provides uniform heat and cost less to operate

Your floor is heated uniformly with no gaps and the radiant heat is dispersed evenly throughout the room. Even heat distribution allows the QuietWarmth systems to cycle quicker resulting in less energy consumption. Also the heat will never exceed 85 degree F, allowing your feet to have the perfect temperature.

• 120V mats work with QuietWarmth 120V systems. 240V will work with 240V.

There is no easier radiant floor heating system to install.

Simple 4 step process!

1. Install underlayment.
2. Roll out electric radiant heat film
3. Hook up electric wiring
4. Install final floor covering

Floor Covering Materials

• All Floating Floors
• Floating Tiles
• Laminate Flooring
• Engineered Wood Flooring
• Luxury Vinyl Flooring (4mm or thicker)
• Cork and Bamboo

Note: Refer to Floor Covering Manufacturer's specifications for compatibility of their product over any radiant heat before installation

• 100 Sq Ft Electric Radiant Floor Heating Mat, 20 Inches Wide x 61 Feet Long, Includes Required GFCI 7 Day Programmable Thermostat - 120VAC
• Highest Quality USA Floor Warming Cable Designed for Longevity by an over 20 Year USA Manufacturer
• Listed and Safe for Wet Locations. Thin profile ~1/8" thick. Multiple Configurations, Adheres to the Floor.
• ETL Listed for US & Canada - Limited Lifetime Warranty by an over 20 Year Trusted USA Manufacturer
• Voltage: 120V - Amps: 10 - Watts: 1200 - 15 ft Cold Lead - 12 Watts/Sqft

User questions & answers

Question:	does this increase the room temperature
Answer:	Yes, it comes with a programmable thermostat and you can set different times for different days of week, and you can program twice a day - so maybe a 3 hour chunk in the morning and other chunk at night.
Question:	Can you install this in concrete in an outside location
Answer:	Certainly possible, I am just not sure how well it will work thru that thickness of that stone. I have heard from others that their floor heater gets too hot to use. Mine is set to 76 and it is not hot, just very comfortable to walk on during the cold ohio weather. I have not cranked it up to the high setting which I think is 82. I would think if your granite supplier is familiar with this and say it works, I would have no hesitation that this unit could not do the job.
Question:	Do you have installation instructions or some video posted somewhere how its set into mortar prior to tile and so on? would be very helpful. Thank you
Answer:	I installed mine directly to the concrete slab and poured a self leveling compound over the top. It works just fine. I think the larger concrete slab acts as a giant heat sink and maybe doesn’t get as warm as it might otherwise and/or takes a little longer to heat up. That said, it works great and gets plenty warm where we actually laid it... in front of the sinks and in front of the shower. If you step off that area you can tell an immediate difference and I wish we’d put down a little more than we did.
Question:	Can you cut the end if you have too much and terminate it
Answer:	Sure, cut mesh and reposition the heating wire the way you need. http://www.heattechproducts.com/how-to-install-radiant-floor-heating-mats

Product description

A gentle electric radiant heat system designed specifically for dry installation under floating wood and laminate floors. A low profile, line voltage system, it features gradual warmth from low wattage resistance heating of ultra-thin, flexible radiant heat film.

Installed easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12 watts per square foot to gently raise the temperature of the floor, conforming to the warranty requirements of many floating floors. The system, which sports an impressive 99% efficiency, includes temperature limiting properties so the film does not overheat.

APPROVED FLOOR COVERING MATERIALS

• All Floating Floors

• Floating Tiles

• Laminate Flooring

• Engineered Wood

• Luxury Vinyl Flooring (4mm or thicker)

• Cork and Bamboo

* Refer to Floor Covering Manufacturer's specifications for compatibility of their product over any radiant heat before installation.

Its available in four convenient rollout mat sizes that will accommodate most any layout.

Each mat has wires pre-attached for ease of installation.

• Uses an highly-efficient conductive ink technology

• Consumes up to 50% less power than traditional wired systems

• Easy to install: roll out, cut length to fit if needed and run pre-attached wires to a wall thermostat

• No mortar and no mess

• Conforms to many floating floor manufacturers requirements

• Disperses an evenly consistent heat throughout the entire floor

KIT INCLUDES THE FOLLOWING

• QuietWarmth 30 Sq. ft. Electric Floor Heating System for Floating Floors - 3' x 10' - 120V

• QuietWarmth 7-Day Programmable Thermostat

• Kit includes: QuietWarmth 3' X 10 - 120V electric floor heating system & QuietWarmth 7-day programmable thermostat
• Easy installation - 3 simple step process (1. Install underlayment, 2. Roll out electric radiant heat film & 3. Install final floor covering)
• Minimal thickness profile - Ultra-thin (less than .016") heated panels keeps same floor heights through room transitions
• Provides uniform heat - Your floor is heated uniformly with no gaps and the radiant heat is dispersed evenly through the room
• Quiets your floor - used in combination with quietwalk underlayment, you achieve a superior sound rating: III 71 & STC 67
• Safety certified - ETL in compliance with UL standards for radiant flooring in the USA and Canada
• Cost less to operate - even heat distribution allows the QuietWarmth systems to cycle quicker resulting in less energy consumption
• Maintenance Free - crafted to not completely shut down If the system should ever become compromised or damaged

User questions & answers

Question:	What kind of underlayment is used
Answer:	For diesel
Question:	Can I use 240v Matt with 120v gauge wiring and circuit breaker
Answer:	Yes. It has a threaded bung hole on top on each end that are the right threads for a 12 v pump.
Question:	How much of thia would i need for a 12' x 20' room
Answer:	Yes
Question:	Can I cut this by length and join again or do I have to throw away whatever I cut
Answer:	Not that I know of think there is some law as to how large. IN my other truck I had a 70 gal made but could not find them all ready built.

Product features

3 ft. x 10 ft. x 0.016 in. 120-Volt Radiant Heat Film for Floating Wood and Laminate Floors (Covers 30 sq. ft.)

Installs easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12 watts per square foot to gently raise the temperature of the floor. The system, which sports an impressive efficiency, includes temperature limiting properties so the film does not overheat. Its available in four convenient rollout mat sizes that will accommodate most any layout.

• Use with most floating laminate, engineered wood and floating tile floors
• Uses an highly-efficient conductive ink technology
• Disperses an evenly consistent heat throughout the entire floor
• Will not add extra height to the floor, only 0.016 in. thick
• Easy to install: roll out, cut length to fit if needed and run pre-attached wires to a wall thermostat
• No mortar and no mess
• Conforms to many floating floor manufacturers requirements

QuietWarmth 7-Day Programmable Thermostat for QuietWarmth Radiant Heat Systems with Built-in GFCI

Designed for underlayment applications, this MP Global Products 7-Day Programmable Thermostat makes it easy to precisely control temperature in your heated floor thanks to a floor sensor and a 4-event timer that allows the programming of automatic comfort and setback temperatures. A built-in ground fault circuit interrupter cuts power in the event of a power surge, helping to protect your floor and radiant system from damage and shield you from injury.

• 7-day (5-and-2) scheduling with 4 programming periods per day for consistent heating and cooling patterns
• Floor sensor monitors temperature to deliver accurate control for your heated floor
• Allows Fahrenheit and Celsius read-out settings for convenient reference
• Built in ground fault circuit interrupter cuts power in the event of a power surge, helping to protect you, your floor and your radiant system
• Compatible with most 120/240-Volt radiant floor heating systems
• 120-Volt power source recommended for heated underlayment applications

Provides uniform heat and cost less to operate

Your floor is heated uniformly with no gaps and the radiant heat is dispersed evenly throughout the room. Even heat distribution allows the QuietWarmth systems to cycle quicker resulting in less energy consumption. Also the heat will never exceed 85 degree F, allowing your feet to have the perfect temperature.

Note: This kit will only work with QuietWarmth 120V systems.

There is no easier radiant floor heating system to install.

Simple 4 step process!

1. Install underlayment.
2. Roll out electric radiant heat film
3. Hook up electric wiring
4. Install final floor covering

Approved Floor Covering Materials

• All Floating Floors
• Floating Tiles
• Laminate Flooring
• Engineered Wood Flooring
• Luxury Vinyl Flooring (4mm or thicker)
• Cork and Bamboo

* Refer to Floor Covering Manufacturer's specifications for compatibility of their product over any radiant heat before installation.

• Combine multiple heating mats of any size to cover your total heating area.
• 15 sq. ft. (18 in. x 10 ft.) underfloor heating pad for laminate, engineered wood and floating wood floor. 120V, 1.0 A, 122 Wt.
• Unique 4-in-1 system: heating, insulating, noise suppressing and moisture wicking heated underlayment pad
• Easy to install. No cement/mortar required for installation under floating floors. Thin, compressed fiber insulation pad limits raising the floor height to 1/8 in.
• ETL listed for USA and Canada. Manufacturer-direct warranty and support. Made in USA.

User questions & answers

Question:	Can you use this under luxury vinyl tile? The lifeproof type with underlayment backing
Answer:	Thinset will not bond well to certain types of tiles. You will need to consult with a thinset manufacturer to make sure you can get a good bond between the tile and membrane.
Question:	Can this be used under ceramic tile
Answer:	The membrane goes directly onto the sub-floor and then heating wire is snapped in between the pillars of the membrane. A heating mat is a different product that does not work with membrane like this. For this you need loose wire that will snap into it.
Question:	are these CSA approved?\
Answer:	Heating element wire sold separately.
Question:	iIwould like to install this under a section of laminate flooring, but not entire 1800 sq ft. What underlayment could i use in the unheated areas
Answer:	Yes

• easy installation - 3 simple step process (1. prepare a clean and stable sub-floor, 2. place quietwarmth tile heat mat, peel back release liner, and adhere to sub-floor & 3. thin set and tile on surface)
• "minimal thickness profile - ultra-thin (less than .03") heated panels keeps same floor heights through room transitions"
• provides uniform heat - your floor is heated uniformly with no gaps and the radiant heat is dispersed evenly through the room
• safety certified - etl in compliance with ul standards for radiant flooring in the usa and canada
• cost less to operate - even heat distribution allows the quietwarmth systems to cycle quicker resulting in less energy consumption
• maintenance free - crafted to not completely shut down if the system should ever become compromised or damaged
• mat size: 3 ft x 5 ft - 240v

Product description

This WarmWire (R) floor warming installation kit contains everything needed for quick and economical installation of a radiant heat flooring system. It makes installation easy and will provide heat to warm the floors and help keep bathroom, kitchen and entry way floors dry and safe. This kit includes a 120 volt floor heating wire that covers a specified area square foot when installed with 3 inch spacing, a SunStat Pro II programmable thermostat, cable strap, double-sided tape, LoudMouth installation monitor, and an in-depth installation manual.

• WarmWire easily installs over plywood, backerboard, or concrete slab.
• Kit includes WarmWire, programmable SunStat thermostat, LoudMouth Alarm, and install accessories.
• Includes heating wire to cover a 30 square foot area.
• Single point power connection makes for easy layout and wiring.
• Dual wire technology reduces electromagnetic fields (EMF) to ultra-low levels.
• Approved for shower applications.
• Connects to 30 volt AC power.
• Energy efficient and affordable underfloor heating solution.

User questions & answers

Question:	how many rolls of wire can one thermostat control? I want to install this on the main floor of my house under a new laminate wood plank flooring
Answer:	yes, when you open the hot water in the bath or kitchen, the water heater automatically starts to heat the water. no need to turn it on.. and it just work when you need hot water
Question:	can the thermostat be programmed to turn on and off
Answer:	AC adapter would be a good upgrade. Why? After two weeks the burner stopped igniting. The spark ignighters work but burner will not light. I pulled panel to go through wires. No gas was going through gas valve solenoid. The reason is D size batteries only lasted two weeks. I changed batteries and it works great again.
Question:	My warranty sheet/card is missing in the box, what should i do? is 25yrs warranty still valid? how do i file it
Answer:	I would not unless you hook vent for exhaust to outside
Question:	How many amps
Answer:	Hello. At this time, the iHeat AHS11-D is not available on Amazon. Feel free to ask us any other questions. GadgetsGo is an Authorized iHeat Distributor. Kind Regards, John M. GadgetsGo

Product features

Install Anytime, Anywhere

• The SunTouch product line includes options for above subfloor, between joist bay, or concrete embedded systems
• Systems are available for warming tile, stone, wood, laminate, and other floor coverings

Proven Reputation

• With over 30 years of experience designing electric floor heating systems, you can feel confident choosing a SunTouch system
• We have a proven reputation with thousands of successful installations across North America

Many Useful Features

• Options for display color themes, remote access, large touchscreens, and control of floor or air temperature
• Reduce energy cost with innovations like an outdoor reset in the SunStat Connect

Electric Floor Heating Cable

SunTouch WarmWire is a series resistance heating cable assembly for installation over plywood, backer board, or a concrete slab (according to ANSI or TCNA guidelines), and then embedded in 3/8 in. (9.5 mm) or greater self-leveling or polymer-modified thin-set mortar.

SunTouch WarmWire cables contain an electric heating wire to provide underfloor heat in bathrooms, kitchens, entryways, and other areas and are an affordable alternative to radiant heated mats. Approved for installation in shower applications where permitted. The durable, constant-diameter wire is easily secured at 2.5 in., 3 in., or 3.5 in. intervals with CableStrap. Controlled by a SunStat floor sensing thermostat (sold separately). WarmWire is available in various lengths with voltage options of 120 or 240VAC.

WarmWire Installation

WarmWire is the most flexible choice for irregularly-shaped or curved rooms and stairs. For typical installations, WarmWire is spaced at 3 inches on center. For areas with high heat loss, the spacing can be lowered to 2.5 inches for added warmth. In hallways and rooms that are well insulated, spacing can be increased to 3.5 inches on center. Controlling the level of warmth is easily accomplished with a connected SunStat Thermostat.

SunStat Thermostat

• Control your floor heating system(s)
• WiFi capability allows control of your system anytime anywhere
• 7-day scheduling capability
• Dual Voltage 120/240V with built-in GFCI for safety and energy use monitoring
• ASIN: B01JDGMGNA

LoudMouth Alarm

• Sounds an alarm if the heating wire is cut or damaged, allowing for easy repair before the mat is covered with mortar and tile
• A green light to indicate GO and a red light to indicate STOP if there's damage
• Simple operation with an on/off switch and a test button
• ASIN: B0080KWIY8

HeatMatrix

• Versatile heating cable compatibility
• Vapor management system
• Shear stress control
• Waterproof
• ASIN: B01N6ROBBY

SunTouch Trowel

• Plastic design reduces risk of damaging wire
• 3/8 inch wide x 1/2 inch deep
• U-shape notches aid in mortar distribution
• For use in electric heated floor applications
• ASIN: B005ZTMPXG

• Combine multiple heating mats of any size to cover your total heating area.
• 60 sq. ft. (36 in. x 20 ft.) underfloor heating pad for laminate, engineered wood and floating wood floor. 240V, 2.3 A, 543 Wt.
• Unique 4-in-1 system: heating, insulating, noise suppressing and moisture wicking heated underlayment pad
• Easy to install. No cement/mortar required for installation under floating floors. Thin, compressed fiber insulation pad limits raising the floor height to 1/8 in.
• ETL listed for USA and Canada. Manufacturer-direct warranty and support. Made in USA.

User questions & answers

Question:	Can this be placed under area rugs over engineered flooring
Answer:	No
Question:	Where can you purchase the thermofloor thermostat? I cannot find it on Amazon
Answer:	5 inches.
Question:	how many can i hook together to 1 thermostate? and which thermostate you recommand
Answer:	Yes, it conforms to all ASTM F876, ASTM F877, CSA B137.5 standards.
Question:	How many btu per sq foot
Answer:	Yes as the description says it is PEX for radiant heat systems. It also says it has an oxygen barrier which most low mass boilers require to minimize corrosion and rust. I hope the resin the pipe is made from is of good quality and will stand the test of time.
Question:	Can I cut the wire off 4’ at the end because it’s more than needed
Answer:	Hello, yes the LuxHeat mat can be used on shower floors, however as with most electric heating systems it is required that the splice (the connection between the cold lead and the heating element), be outside of the shower itself. This can easily be achieved by laying a small section of the mat outside the shower, or by removing a loop of wire from the mat, thus allowing the splice to be 2-3 feet outside the shower base.
Question:	What is the high temperature it can generate
Answer:	Hello, To deactivate the child-lock press the “OK” button to activate the menu, then press and hold the Up and Down buttons simultaneously for three seconds. A copy of the User Manual for this thermostat may be viewed and downloaded from our website here: https://cdn.shopify.com/s/files/1/0061/5569/8240/files/UDG-4999_user_manual.pdf?v=1605619906 Or visit https://proluxmaterials.com/pages/downloads.
Question:	where can I find additonal floor sensors
Answer:	Hello, yes the floor heating mat must be set in mortar or a self-leveling screed as this ensure even heat distribution.
Question:	Can I use a different thermostat? For example one that is homekit compatible
Answer:	Hello, the LuxHeat floor heating system must be covered with a mortar or self-leveling compound, this provides sufficient heatsink, and promotes even heat distribution throughout the floor.

• TEMPZONE ELECTRIC RADIANT FLOOR HEATING CABLE: WarmlyYours TempZone Electric Radiant Floor Heating Cable is cULus Listed and designed for applications under ceramic tile, natural stone, nailed hardwood, wood floors, this 595 ft. free-form cotton cable provides an alternative for installers who prefer the flexibility and freedom of working with loose cable, can be installed at either 3" or 4" and is available in two voltage options, is ultra-low EMF by design, also features a low profile (1/8 inch thick) twin conductor with a 15’ cold lead
• nSPIRE TOUCH PROGRAMMABLE THERMOSTAT: This dual voltage (120V/240V) thermostat comes with energy log for tracking use and built-in self-testing GFCI, features "Child-Lock" function and a 3.5” full color touchscreen, complimentary floor sensor allows for energy efficient operation of your floor heating system, with the ability to set up 4 separate temperature events per day and the integrated install wizard, lets you customize your comfort while cutting down on operating cost
• PRODESO HEATING CALBE MEMBRANE ROLL: This cost- and time-effective 162+54 sq. ft. sheet of membrane allows quick installation of floor heating over a variety of different substrates such as tile, marble, and stone floors, provides uncoupling and crack isolation benefits, features integrated channels are shaped to easily and securely hold the TempZone Electric Radiant Floor Heating Cable, makes it easy to maintain proper spacing throughout an entire project
• FLEXIBLE HEATING COVERAGE: This kit comes with a 595 ft. long heating cable which can provide between 185.9 sq. ft. of heating coverage at 3.75” spacing (ideal spacing for optimal heat output) in membrane and 247.9 sq. ft. of heating coverage at 5” spacing

User questions & answers

Question:	Can i use this under real wood floor
Answer:	No. Binary is an on/off (0 or 1) system. This remote would likely be considered as a Ternary system since it offers three settings - 0, +, and -. All of the remotes I've encountered offer this system. Download the user guide - it provides full detail. Also, Check your receiver. What are the options there? Likely 0, - , and+.
Question:	what is the thinkness of the mat
Answer:	I don't know. Mine is an Allstar 6500.
Question:	Why does the description say 180 ft? When i have it on
Answer:	I don't think this will work unless you have an Allstar receiver on the back of the operator
Question:	Can I pour a self leveler over the cable
Answer:	No. I tried programming it to my Allstar opener - circa '96, but no luck. It doesn't support openers with 10 dip switches or more. However, what remote did work for me, and was truly 'universal' was the "Chamberlain model KLIK1U". You can program it either with the 'smart/learn' button -or if like me you have 'dip switches'.
Question:	Can I cut the wire off 4’ at the end because it’s more than needed
Answer:	Have no idea sorry
Question:	What is the high temperature it can generate
Answer:	Segment Reprogram remote control wall garage door openers 1 press learn button once & release. 2. Press remote control button then you will see a light on your garage motor turn off. 3. Test opener Good luck to you
Question:	where can I find additonal floor sensors
Answer:	Yes, it will work for that model, but you have to reset and reprogram your AllStar Garage Door Openers 110838 Wall Console motor. Good luck!
Question:	Can I use a different thermostat? For example one that is homekit compatible
Answer:	I don't think so. I looked at the compatibility of MVP and Liftmaster was not listed. Here is a link to Liftmaster compatible remotes: http://chamberlain.custhelp.com/app/answers/detail/a_id/209/~/liftmaster%C2%AE-remote-compatibility

• Complete heating system - including everything needed
• Simple and reliable heating cables that we have used since 1991.
• A precise multifunctional digital programming thermostat with installation box
• installation manual

User questions & answers

Question:	Is this for under tile flooring and does it come with clips to hold the wirer in place? Can I see a set of instructions
Answer:	not sure sure,but if the garage door motor is prior to 1992 chances are good that it will work
Question:	What is the diameter of the wire
Answer:	I replace this model Allstar 600 last year for lift master the motor stop working after 27 year,but I still have remotes you can have it you can program the code with this remote with Allstar 600
Question:	I just need for 100sf. May I use only one spool of two
Answer:	I don't know but this one below should.http://www.amazon.com/Allstar-9921T-Remote-Garage-Transmitter/dp/B000CZ2GN2/ref=sr_1_fkmr0_1?ie=UTF8&qid=1398733588&sr=8-1-fkmr0&keywords=Allister+model+ADX+921
Question:	How many feet of wire on the spool
Answer:	Yes will work, you program your code need to be the Same as the control panel, I no longer have the all o magic motor after 27 years motor went but I have the 4 remote that is in good condition