12 best buis for ar 15s

Product description

Impact resistant polymer construction provides light weight and resists operational abuse

Spring-loaded flip up sight easily activated from either side or by pressing the top

Detent and spring pressure keeps sight erect but allows for unobstructed folding under impact, etc.

Clamps to most any MIL-STD-1913 Picatinny/STANAG 4694 railed hand guard and provides the same height-over-bore as standard A2 irons

Protective wings shield the dual, same plane flip apertures & spring-locking A2 front sight post

Elevation adjustment tool included, but most aftermarket A2 front sight adjustment tools may be used as well

Detent knob easily and positively adjusts windage



MBUS - Front Gen 2

Weight, w/ hardware: 1.2 oz.

Height above rail, stowed: ~0.51 in.

Length, stowed: 2.6 in.

Length, deployed: 1.5 in.



NOTE: Cannot be mounted to a railed gas block due to excess heat issues. Front MBUS must be mounted to a railed fore end on the same plane as the receiver rail. Because of this the sight is also not compatible with MOE Hand Guards.



MBUS - Rear Gen 2

Weight, w/ hardware: 1.3 oz.

Height above rail, stowed: ~0.51 in.

Center of aperture to top of rail: 1.42 in.

Length, stowed: 2.6 in.

Length, deployed: 1.5 in.

• Impact resistant polymer construction provides light weight and resists operational abuse
• Spring-loaded flip up sight easily activated from either side or by pressing the top
• Detent and spring pressure keeps sight erect but allows for unobstructed folding under impact, etc.
• Clamps to most any MIL-STD-1913 Picatinny/STANAG 4694 railed hand guard and provides the same height-over-bore as standard A2 irons
• Protective wings shield the dual, same plane flip apertures & spring-locking A2 front sight post

• With return springs and leg release button, the leg length can be adjusted from 6 inches (152mm)to 9 inches(225mm).
• Made of hardened steel and aluminum, non-rust black anodized finish, the rifle bipod is duty and light weight.
• Adjustable leg length: 5 settings for different length, the bipod is ready to meet your needs.
• Quickly attach to or detach from the rifle using existing swivel stud.
• Foldable arms with spring tension control. Come with the mount adapter.

User questions & answers

Question:	How do i attatch the rail mount to the bipod itselfl
Answer:	Yes... Remove the plastic tube from the bipod, untwist the thumb screw, thus will loosen the fingers. Place onto the piece that mounts to your to your rail system, finger tighten then attach the bracket to your rail at desired location and tighten with supplied allen wrench. The plastic protection tube can throw you off...
Question:	Would tho bipod fit on a springfield saint ar 15 5.56 rail
Answer:	This bipod comes with a weaver/pictatinny mount adapter so if your fire arm has either of those rail types, it will fit. It requires about 4 slots on a picatinny rail (just an estimate).
Question:	Can a sling be mounted to the attached bipod? I don't want to give up my sling to mount a bipod
Answer:	Yes, there is the ring on the bipod for you to attach sling.
Question:	Does it have the swivel or pivot feature
Answer:	It doesn't have a swivel or pivot feature, however I just got mine and mounted it and just checking it out at home I found that you actually can pivot up and down a reasonable amount, and I was actually able to pivot it a good amount as well. Didn't measure, but probably around 20-30 degrees worth, which would translate to many moa's and a good amount of distance at range. I had a bipod with swivel and pivot features and it never really locked in like I would have liked, so I actually like the way this one feels more. First impressions are really high. So far I can't tell the difference between this one and a much more expensive 'famous maker' one I had. Will be taking it out in the next day or two and can't wait.

Product description

⭐️ NEW HARDENED AIRCRAFT GRADE ALUMINUM ALLOY!



✔ THE QUALITY



The Tacticon Flip-Up Front And Rear Iron Sights are a high-quality aluminum alloy. Whether using as your main sight or as a back-up sight for another optic, you can count on the accuracy and durability this sight offers. The spring loaded pop-up action on the iron sights is incredibly fast and effective with the simple push of the button.





✔ THE WARRANTY



These iron sights are fully refundable if you are not satisfied with them. We offer a lifetime warranty on the sights.





✔ THE FLEXIBILITY



It is designed for any hunting or tactical rifle including Winchester, Remington, Colt, etc. and can fit ANY rifle and will fit all Picatinny Rail and Weaver Rail sections.





✔ THE ADJUSTABILITY



The front sight post is fully adjustable for elevation and we INCLUDED the front sight post adjustment tool for your convenience! The rear sight is fully adjustable for windage.





✔ THE INSTALLATION



Allen wrench to easily mount the iron sights is included with this product unlike most other sights on Amazon. How terrible would it be to get these awesome iron sights then have to drive to the hardware just to mount them on your rifle?





✔ THE PACKAGING



Whether you're keeping this for yourself or giving this to someone for an awesome gift you will be pleasantly surprised when you crack open the packaging. Makes for an awesome gift box and/or ammo box!!!

• ✔ FRONT SIGHT ADJUSTMENT TOOL INCLUDED! This front sight elevation tool is included! It sells for $10 by itself on Amazon!
• ✔ TACTICON IS A COMBAT VETERAN OWNED COMPANY - STURDIEST AND BEST BUILT IRON SIGHT ON AMAZON - Made out of actual metal (hardened aircraft grade aluminum alloy), not polymer like some of these cheap imitations on Amazon
• ✔ COMES WITH WOODEN CASE AND FRONT SIGHT ADJUSTMENT TOOL - Keep the sight adjustment tool and the mounting wrench along with some extra ammunition in this awesome box we include with your purchase.
• ✔ PUSH BUTTON FLIP UP WITH EASE - Simply the press of a button and your iron sights will pop up quickly.
• ✔ MOUNTING WRENCH INCLUDED - No other iron sights on Amazon come with the allen wrench and the front sight adjustment tool!

User questions & answers

Question:	The push button has a knob. What does it do
Answer:	I have been trying to get my rear sight warrantied for months and only get a completely useless e-mail response in return. Good luck. If you get anywhere with your warranty, please let me know how you did it.
Question:	Who do you call for the life time warranty
Answer:	A customer can have it in any color they want as long as it's black
Question:	Does this come in tan
Answer:	The are DEFINITELY made in China. The box is marked "Made in China".
Question:	Where are they made
Answer:	I think everything is made in China. It’s a good sight for the money . I like mine

Product description

Building on the proven MBUS Pro platform, the MBUS Pro Offset Sights are part of an an effective aiming system to supplement magnified optics on 1913 Picatinny mounting surfaces. In the event of a damaged or nonfunctional primary optic, or a close target, rotating the rifle 45 degrees provides the shooter with a fully-featured iron sighting solution. The MBUS Pro Offset Front Sight features durable Melonited steel construction, positive detented lockup when deployed, tool-less adjustment of the front post for easy zeroing, and a low profile footprint to ensure compatibility and reduce interference with most rifle setups.

 

• All steel construction; Steel, rectangular sight post selectable between Match and Standard widths (.040” Match width for increased precision; .060” Standard width for maximum visibility)
• Case hardened and finished with Melonite QPQ for extreme resistance to wear and corrosion
• Mounts on any MIL-STD-1913 Picatinny/STANAG 4694 rail including receiver-height gas blocks
• Elevation adjustment knob – no tools required; Positive detents in both the up and down positions as well as on the elevation knob
• Standard height over bore when deployed, 45 deg. offset right-hand side

User questions & answers

Question:	How much rail space does the rear sight need
Answer:	It is NOT designed to work on the Right rear. The arm will NOT fully extend because the wire sheath around the 7 wires will be oriented on the outside toward the back of the drone, preventing full extension. All 4 arms are different. The rear arms have their motors mounted ~1/2" higher than the front so that when all 4 are extended they are the same height. Then, the polarity(direction) of the motors for the Front 2 arms are opposite each other. The same is true for the rear. Even if you buy a Left Front arm with the same polarity, the motor height will be too low. If you buy this arm and figure out how to reverse the polarity, you still will not be able to fully extend the arm.
Question:	Does it have 2 apertures? Small hole? Big hole
Answer:	2 Seals come with the kit. Thanks for your interest.
Question:	Does this include both front and rear sights
Answer:	yes used one on my Troy Bilt horse last year. Perfect fit.
Question:	Are these sights "lefty" compatible? Do they reverse
Answer:	Take the number off your tiller and use that number to look it up

Product description

✔ THE QUALITY



The Tacticon 45 Degree Offset Flip-Up Front And Rear Iron Sights are a high-quality aluminum alloy. Whether using as your main sight or as a back-up sight for another optic, you can count on the accuracy and durability this sight offers. The spring loaded pop-up action on the iron sights is incredibly fast and effective with the simple push of the button.





✔ THE WARRANTY



These iron sights are fully refundable if you are not satisfied with them. We offer a lifetime warranty on the sights.





✔ THE FLEXIBILITY



It is designed for any hunting or tactical rifle including Winchester, Remington, Colt, etc. and can fit ANY rifle and will fit all Picatinny Rail and Weaver Rail sections.





✔ THE ADJUSTABILITY



The front sight post is fully adjustable for elevation and we INCLUDED the front sight post adjustment tool for your convenience! The rear sight is fully adjustable for windage.





✔ THE INSTALLATION



Allen wrench to easily mount the iron sights is included with this product unlike most other sights on Amazon. How terrible would it be to get these awesome iron sights then have to drive to the hardware just to mount them on your rifle?





✔ THE PACKAGING



Whether you're keeping this for yourself or giving this to someone for an awesome gift you will be pleasantly surprised when you crack open the packaging. Makes for an awesome gift box and/or ammo box!!!

• ⭐️ NEW HARDENED AIRCRAFT-GRADE ALUMINUM ✔ FRONT SIGHT ADJUSTMENT TOOL INCLUDED! This front sight elevation tool is included! It sells for $10 by itself on Amazon!
• ✔ TACTICON IS A COMBAT VETERAN OWNED COMPANY - STURDIEST AND BEST BUILT IRON SIGHT ON AMAZON - Made out of actual metal (aluminum alloy), not polymer like some of these cheap imitations on Amazon
• ✔ COMES WITH WOODEN CASE AND FRONT SIGHT ADJUSTMENT TOOL - Keep the sight adjustment tool and the mounting wrench along with some extra ammunition in this awesome box we include with your purchase.
• ✔ 45 DEGREE OFFSET ✔ PUSH BUTTON FLIPS UP WITH EASE - Sights are offset 45 degree to allow you to slightly rotate your weapon to witness target through them and engage. A simple press of the button and your iron sights will pop up quickly.
• ✔ MOUNTING WRENCH INCLUDED - No other iron sights on Amazon come with the allen wrench and the front sight adjustment tool!

User questions & answers

Question:	Can you order left side sights. Their website says “not ambidextrous
Answer:	I am not associated with the seller. So I defer to their answer. But mIne are mounted to right. My sites fold toward me. I don’t see what you could not mount left. The would away from you. You would see the opposite side when up, but to-mato tom-ato. The base bracket has a tiny hole to hold the spring for tension. If you re-drilled you could rotate to see the intended side. But either way I think you would be okay.
Question:	Why did the price go up wernt these $19 lat week
Answer:	They were $19.95 last week but that was our introductory price for the launch of the product with new hardened aluminum. That price barely covered my cost to make them so I had to raise the price by $5 to make a small profit, I hope that's ok! Still the best priced and best reviewed 45 degree iron sights on Amazon right now! Thanks for your inquiry my friend!
Question:	Will these work with a panther oracle ar
Answer:	Will work with any AR 15 with a picatinny rail.
Question:	can the offset be switched left vs right? i.e. can rear sight be mounted on top rail and front sight be mounted on right-side rail
Answer:	You can mount them either direction.

Product description

Building on the proven MBUS Pro platform, the MBUS Pro Offset Sights are part of an an effective aiming system to supplement magnified optics on M1913 Picatinny mounting surfaces. In the event of a damaged or nonfunctional primary optic, or a close target, rotating the rifle 45 degrees provides the shooter with a fully-featured iron sighting solution. The MBUS Pro Offset Front Sight features durable Melonited steel construction, positive detented lockup when deployed, tool-less adjustment of the front post for easy zeroing, and a low profile footprint to ensure compatibility and reduce interference with most rifle setups. The MBUS Pro Offset Rear Sight features durable Melonited steel construction, positive detented lockup when deployed, tool-less windage adjustment for easy zeroing, dual rear apertures, and a low profile footprint to ensure compatibility and reduce interference with most rifle setups.

• All steel construction; Standard height over bore when deployed, 45 degrees offset right-hand side
• Case hardened and finished with Melonite QPQ for extreme resistance to wear and corrosion
• Elevation and Windage adjustable with low-profile knob; no tools required
• Positive detents in both the up and down positions
• Made in U.S.A.

User questions & answers

Question:	Are these genuine Magpul? Can I return if not
Answer:	Yes this will work on 23XX size motors. I have successfully used them on everything from 2306 down to 1306 motors. You need various levels of a firm grip based on the tightness of the locknut. I tighten the lock nuts on my props until i can turn the bell with the prop while holding it just with my fingers. If you are cranking it down till the bell starts to slip out of the pliers then it is probably too tight and you are going to wear out the rubber inserts.
Question:	Are these gen 1 or gen
Answer:	dear buyer, please check the image2,there is a wiring diagram. if you have any question or problem,please contact us: [email protected] we will provide you the better solution.
Question:	When attached to a rail hight gas block would the front sight obstruct a magpul sl handguard
Answer:	Yes they are. I bought this for my HS720E and it works just great.
Question:	Is this an official magpul product that is made in the usa...or a chinese knock-off
Answer:	Yes, the wires are attached to it. They were delivered, but we haven’t put them on yet so I’m not sure how big of a job that’s going to be.

Product description

Building on the proven MBUS Pro platform, the MBUS Pro Offset Sights are part of an an effective aiming system to supplement magnified optics on 1913 Picatinny mounting surfaces. In the event of a damaged or nonfunctional primary optic, or a close target, rotating 45 degrees provides the shooter with a fully-featured backup sighting solution. The MBUS Pro Offset Front Sight features durable Melonited steel construction, positive detented lockup when deployed, tool-less adjustment of the front post for easy zeroing, and a low profile footprint to ensure compatibility and reduce interference with most setups.

• All steel construction; Steel, rectangular sight post selectable between Match and Standard widths (.040” Match width for increased precision; .060” Standard width for maximum visibility)
• Case hardened and finished with Melonite QPQ for extreme resistance to wear and corrosion
• Mounts on any MIL-STD-1913 Picatinny/STANAG 4694 rail
• Elevation adjustment knob – no tools required; Positive detents in both the up and down positions as well as on the elevation knob
• Standard height when deployed, 45 deg. offset right-hand side

User questions & answers

Question:	Do they have these in fde
Answer:	Yes dual aperture. Thanks.
Question:	I'm left handed. Do they make them for left handed shooters? I'd be rolling the gun to the right. Thanks in advance
Answer:	No, Magpul MBUS PRO Offset sights are sold individually ( Front Offset is MAG#525, Rear Offset is MAG#526)
Question:	Are the front and rear sights flippable? They look like they have a pivot point, but I have been on about 10 sites and none of them specifically say
Answer:	Just rotate your picatiny mount to top of rifle then you have your sights on leftside. I'm lefty. Just don't have money to purchase. Hope I helped.
Question:	Can they mount on the left side
Answer:	They should open wide enough to grip a 2205 motor. They should work on motors up to 23xx, as the description states.

• Machined from lightweight and extremely durable aluminum, Mil-Spec hard anodized
• Calibrated and matched together as a set, Designed for same plane with low profile rear sight
• Flip-up design with spring load push button, allowing for quick deployment Rear sight Windage adjustable
• Rear sight: micro style windage knob features same MOA adjustment as standard sight
• Front sight: A2 post Elevation adjustment （Adjustment Tool not included, you can search front sight adjustment tool on Amazon to get one), 100 percent satisfaction guaranteed

User questions & answers

Question:	will this fit a radical arms ar
Answer:	they will fit if the rifle has standard picatinny rails which most do.
Question:	Can anyone verify if the front sight post is the same size as a standard Ar sight post as i would like to put an aftermaket in
Answer:	definitely too high for a a4/ar15. I cant even see the laser of the foresight at all. If you measure the front sight is about 3/8" larger than the rear. If you read the description closely, all the wayyyyy at the bottom it says it's a standard A2 front sight.!
Question:	How close of a proximity can the front and rear sight be mounted from eachother on a standard Mini 14 6" picatanney mount
Answer:	These sight ar really for a longer sight plane. (AR 15). You would be better off with the sights that came on your Mini 14 if you are looking for accuracy. Thi
Question:	Will this for a Mck gen 3 or roni
Answer:	Mounted on my Roni, will not sit level, about a 5 degree cant to the left.

Product features

1. Feyachi Flip Up Rear Front and Iron Sights with Elevation

Specification

• Dimensions: 35mm x 45mm (height) x 30mm, Weight:1.5 oz (Front) 35mm x 40mm (height) x 27mm, Weight:1.8 oz (Rear)
• Color: Black finish
• Material: Aluminum
• Interface: Picatinny / Weaver Rails

Flip-up Design

Flip-up design with spring load push button, allowing for quick deployment

2 Mode

Adjustable for CQB or long range Mode

Rear Sight Windage Adjustable

Rotate the knob to adjust the windage.

• Impact resistant polymer construction
• Made in the USA
• Impact resistant polymer construction provides light weight and resists operational abuse
• Spring-loaded flip up sight easily activated from either side or by pressing the top
• Detent and spring pressure keeps sight erect but allows for unobstructed folding under impact, etc.
• Clamps to most any MIL-STD-1913 Picatinny/STANAG 4694 rail and provides the same height-over-bore as standard A2 irons
• Protective wings shield the spring-locking A2 front sight post; Elevation adjustment tool included, but most aftermarket A2 front sight adjustment tools may be used as well

User questions & answers

Question:	is it really adjustable for elevation
Answer:	As far as they Go they are Pro series. Full alloy compared to their polymer siblings that come in gen 1 and 2 these would be the gen 3.
Question:	How many slots does it take on the rail
Answer:	From what I could find about the sl hanguard it would.
Question:	Does this site have two rear aperatures..one larger than the other and if so how do they work..how do you change from one to another
Answer:	ALL our products, including Magpuls, are genuine, OEM, Made in the USA, products. Thank You for your interest. Nimrod's Wares
Question:	Is this the genuine Mag Pul for 5.56 AR15, or the Airsoft version
Answer:	I believe the answer is two. More specifically, it cover up two positive "humps" and two negative "slots" on the rail. It covers the exact same amount as the front sight does as well if that helps.

Product description

The MBUS (Magpul Back-Up Sight) is a low-cost, color injection molded, folding back-up sight. The MBUS Front Sight is adjustable for elevation and fits most 1913 Picatinny-railed hand guards, but is specifically tailored to the .223 platform. Impact resistant polymer construction provides light weight and resists operational abuse. Spring-loaded flip up sight easily activated from either side or by pressing the top. Detent and spring pressure keeps sight erect but allows for unobstructed folding under impact, etc. Clamps to most any MIL-STD-1913 Picatinny/STANAG 4694 railed hand guard and provides the same height-over-bore as standard irons. Protective wings shield the spring-locking front sight post. Elevation adjustment tool included, but most aftermarket front sight adjustment tools may be used as well. NOTE: Cannot be mounted to a railed gas block due to excess heat issues. Front MBUS must be mounted to a railed fore end on the same plane as the receiver rail. Because of this the sight is also not compatible with MOE Hand Guards. MAG248-OD: The MBUS (Magpul Back-Up Sight) is a low-cost, color injection molded, folding back-up sight. The dual aperture MBUS Rear Sight is adjustable for windage and fits most 1913 Picatinny rail equipped weapons, but is specifically tailored to the .223 platform. Impact resistant polymer construction provides light weight and resists operational abuse. Spring-loaded flip up sight easily activated from either side or by pressing the top. Detent and spring pressure keeps sight erect but allows for unobstructed folding under impact, etc. Clamps to MIL-STD-1913 Picatinny/STANAG 4694 receiver rail and provides the same height-over-bore as standard irons. Protective wings shield the dual, same plane flip apertures. Sight can still be folded with either large or small aperture in position. Detent knob easily and positively adjusts windage.

• Olive Drab Green Color
• Front and Rear Sights Included
• Made in USA

User questions & answers

Question:	Do they say "gen 2" on them? how can you tell from other mbus sights
Answer:	hello and thanks for writing Rock Mountain Tactical. There are only GEN2 since about 2010. The previous version were GEN1 and are larger than these. Ours are authentic Magpul. There are PTS versions out there and are usually way cheaper. PTS are copies for airsoft. These are not PTS. Thanks for looking. V/R, Rock Mountain Tactical
Question:	Will these sites lineup with optics like the spark
Answer:	yes, I have them on all my rifles along with VTM sights and leepers
Question:	This is for the seller - do you have a set like this in black
Answer:	yes, but not currently listed on amazon.
Question:	Will Magpul mbus sights fit an M&P 15 sport
Answer:	Yes as long as it has standard picatinny rail.

Product description

✔ THE QUALITY: Bear Armz Tactical's Flip-Up Front And Rear Sights are made of HARDENED AIRCRAFT GRADE ALUMINUM ALLOY! They are super durable and dependable. At Bear Armz Tactical we only sell products that we use and love ourselves.



✔ LIFETIME WARRANTY: ***100% Satisfaction Guarantee, buy with confidence *** If you are not 100% satisfied contact us for a full refund, no questions asked, it is that easy.



✔ THE FLEXIBILITY: Will fit ALL Picatinny Rail and Weaver Rail sections.



✔ THE ADJUSTABILITY: The front sight post is fully adjustable for elevation and rear sight is fully adjustable for windage. With the simple push of a spring loaded button your back up sights deploy and are ready to use.



✔ THE INSTALLATION: Installation is easy and we include the allen wrench needed to install these sights in no time. We have no doubt that you will be impressed by the accuracy and quality of these sights.



🌟 Click the yellow "Add to Cart" button above to get your premium Flip-Up Irons Sights today! 🌟



If you have any issues with your order please shoot us a message and we will get the issue resolved right away.

• ✔ USA COMPANY & LIFETIME WARRANTY: 🌟 100% Satisfaction guarantee, buy with confidence. 🌟 We are an AUTHORIZED DEALER based in the USA and are here to get the best products possible in your hands for a reasonable price!
• ✔ ADJUSTABILITY: Fully adjustable for windage and elevation.
• ✔ QUICK DEPLOYMENT: Milled aircraft grade aluminum flip up front and rear sight spring loaded for quick deployment.
• ✔ UNIVERSAL DESIGN: Fits all picatinny rails and is easy to install.
• ✔ ALLEN WRENCH INCLUDED: No other sights on Amazon come with the allen wrench!

User questions & answers

Question:	Do the sights lock in the upright position; must the release button must be depressed to lower the sights
Answer:	Sights are spring load. pressing the button pops them up and locks into position. Press the button to release and push them down.
Question:	Are the company labels removable
Answer:	The only way to remove them would involve damaging the metal requiring repainting.
Question:	Are these based on a1/a2 style? what tool do i need for the front site
Answer:	Not 100% positive on a1/a2 style, but the tool should be included for mounting it.
Question:	Where are these made
Answer:	Actually owning these I will say, I believe in china, BUT...... Don't let that turn you away. These are hardy, sturdy, and durable. They are easily adjusted and extremely easy to use. Bear Armz Tactical IS a US company. I have a set and they are great.

Product description

Why choose Bugleman Flip Up Front Rear Sights?

Simple to Flip up

❖ Thumb slide flip-up Spring-loaded mechanism. Sliding the spring load push button to flip-up simply. Spring-loaded Flip Up Front and Rear Sight is easily activated by pulling the back cover.

 

Front Sight & Rear Sight

❖ Front Sight is completely adjustable for Elevation by rotating the adjustment gear.

❖ Rear sight can be switched between CQB and Precision by dual aperture design.  

❖ You can rotate the knob for a proper aiming position in rear sight.

 

Durable & Lightweight & Solid

❖ Impact resistant polymer construction provides you with Durable & Lightweight & Solid use experience.

Package Includes:

❆ 1 x Front Sight

❆ 1 x Rear Sight

❆ 1 x Allen Wrench Tool

• ❖【Simple to Flip up】Thumb slide flip-up Spring-loaded mechanism. Sliding the spring load push button to flip-up simply. Allowing for quick deployment and adjust the deployment according to your needs. Spring-loaded Flip Up Front and Rear Sight is easily activated by pulling the back cover.
• ❖【Front Sight - Elevation Adjustment】 Front Sight is completely adjustable for Elevation by rotating the adjustment gear.
• ❖【Rear Sight - Two Mode & Precise Aiming】Switch between CQB and Precision by dual aperture design. With the scale mark on the rear sight, you can rotate the knob for a proper aiming position.
• ❖【Impact resistant polymer construction】Impact resistant polymer construction provides you with Durable & Lightweight & Solid use experience, there is a allen wrench tool in package, so you don't need to find tool.
• ❖【100% Moneyback Guarantee】Choose us, you will get 1 × Front Iron Sight, 1 × Rear Iron Sight, 1 × Allen Wrench Tool. We provide 100% satisfaction Money-back guarantee when you don’t like our product and want refund. But Please Note: It is not suitable for railed gas block.