12 best hot water tank for mobile home

Product description

Get hot water where it's needed, when it's needed with the Bosch ES4 Tronic 3000 T Electric water heater. This 2.5-gallon capacity point-of-use mini-tank fits right under your sink and provides a practical and effective solution to your hot water needs. This smaller model can be plugged right into a 120-volt outlet with the 36-37" cord, or can be installed in-line with a larger hot water source to provide "on-demand" use. The glass-lined tank offers great insulation and added durability, while the heater's fast recovery rate eliminates long waits for hot water. An external dial allows you to easily control the temperature range, and the temperature-and-pressure relief valve enhances your safety. The ES4 Tronic 3000 T from Bosch has a sleek and attractive exterior design that blends in seamlessly with existing decor when installed in a visible location, making this heater a great option in any room.

Manufacturer Contact Information

800-283-3787

• CONVENIENT HOT WATER HEATER: 2.5 gallon point-of-use mini-tank fits under your sink to provide hot water right where you need it. Thermal efficiency is 98%. Dimensions : 13.75 W x 13.75 H x 10.75 D Inches
• LONG LASTING QUALITY: This electric water heater is easy to maintain and has premium glass-lined material for a long service life. (Amps 12A, Volts (VAC) 120)
• INDEPENDENT INSTALLATION: 36-37" cord plugs into a 120 volt outlet for independent installation or in-line with a large hot water source
• FAST RECOVERY RATE: Eliminates long waits for hot water at your sink, get on demand hot water at your every need (supplies up to 2 sinks at a time)
• EASILY MOUNTED: Can be shelf, wall or floor mounted (bracket included); simply tap into the cold water line and install the water heater directly at the sink to provide hot water

User questions & answers

Question:	Is it necessary to connect an expansion tank to this heater (for safety purposes)? It states something to that effect in the user manual
Answer:	The expansion tank for this heater is not required. Most people already have these installed in their homes but if not then it would be Ok without it as there is a pressure relief valve on top if something happened. GlobalTowne is an authorized Bosch distributor.
Question:	would this be able to supply a shower
Answer:	A standard flow shower head is around 2.5 gallons per minute. A low flow head is around 1.5 gallons per minute. The recovery rate for a 90 degree temperature rise is 6.8 gallons per hour! So even the 7.5 gallon unit would only provide 4 minutes of shower time before the temp dropped off dramatically. (even at the low flow rate..)
Question:	Can be used "in-line with a large hot water source"? Would it help a large bathtub that runs out of hot water before it gets full from main tank
Answer:	If your bathtub is bigger than your main heater tank, this unit isn't going to do much for you. It will add 2.5, 4, or 7 gallons to the capacity of your main tank, depending on which Bosch unit you buy. The 7 gallon unit requires a specially wired circuit. You will also get a little bit of lukewarm water that was in the line between your main heater and the Bosch unit. Unless your main tank is awfully small and your bathtub massive, the 4 gallon unit should work for you. Maybe a demand type thankless heater in your bathtub hot water feed would be a better choice, but be careful to size it properly for your desired flow rate and temperature rise. Also a tankless is likely to require special wiring.
Question:	When this heater is connected to the hot water line, what happens with the cold water that was sitting in the pipes
Answer:	When the tap is opened, the hot water in the unit flows out. The colder water that was sitting upstream of the unit, enters the unit to be heated. If the tap remains open, the newly heated water flows out, being replaced eventually, (depending on the distance to the main water heater), with the water from the main water heater. You will probably set the unit temperature to equal the main water heater temperature, if you want to keep a constant temperature, but other scenarios are possible.

Product features

Bosch ThermoTechnology

The Bosch Tronic 3000 T point-of-use electric mini-tanks are available in three compact sizes, which can be wall-hung (bracket included) or floor-mounted. They fit easily under a sink, even in a cabinet space, and because they have a sleek and attractive design, they blend in seamlessly with existing decor when installed in a visible location. Simply tap into the cold water line and install the water heater directly at the sink to provide hot water. Great for a wide range of locations!

Water Where You Need It

Provides hot water quickly at point of use and comes with temperature /pressure relief valve installed - 2.5 and 4 gallon tanks feature a simple 120 VAc plug-in connection (1440 watts).

Quality for Long-Life

Thick CFC-free foam insulation for maximum energy efficiency, glass-lined tank for durability.

Great for Small Spaces

Water heaters are compact and lightweight and can be floor, shelf, or wall mounted (except 7 Gallon) - features a sleek and attractive design to blend seamlessly with decor.

Minimize Wait Time for Hot Water

Waiting for hot water at a sink located far from a primary heating source can be frustrating. Only having access to cold water from a sink is just not useful, and plumbing a hot water line to every sink in a home or business requires time and money. To get hot water where it’s needed, when it’s needed, a better solution is to use the Tronic 3000 T from Bosch: a point-of-use electric mini-tank heater. This heater can supplement a primary water heating source, or be used under a single sink. In fact, the Bosch Tronic 3000 T can be used for three different applications: as a sole water heating source for a single sink, as a supplement to an existing heater located far from the sink, and as a buffer installed in-line with tankless water heaters that experience intermittent cold water, also known as 'cold water sandwiching'. No matter the configuration, there’s minimal stand-by loss from this premium mini-tank water heater.

Product description

606 series. 1650/120V. UL listed. No dip tube since the bottom inlet eliminates need for it. 1" foam insulation/16.00 R-value. Factory installed T&P valve. Meets NAECA codes. Glass lined tank. Inlet and outlet connections on side for easier installation in tight spaces. Warranty: 6 year tank/parts.

From the Manufacturer

Series 606 electrics provide up to 4,500 watts/hr. input — plenty for all your hot water needs.

• Ideal for under counter or crawl space installation
• 6 gallon short, 6 year warranty, electric.
• Single 120 volt 1650 watt copper heating element.
• Side mounted cold water inlet and hot water outlet for easy installation.
• Factory installed Temperature and Pressure, T&P relief valve

User questions & answers

Question:	Does this plug into a 110 recepticle or do you need to hard wire it
Answer:	From the description of the item, "Dimensions (each): 16.75W x 4.5D x 11.5H in"
Question:	can i plug this in to a regular wall outlet? if so would it need its own outlet
Answer:	My experience with these filters has been the replacement intervals is more about how much water you are going through than it is about time. I probably replace them every 20 fillups. I know it is time to replace them when the water stops absorbing more than halfway up the wick filter.
Question:	how many amps does the water heater use
Answer:	Hi, Vince. Thank you for the question. The highest humidity setting is 65%. Thanks. -Natalie, Essick Air Products
Question:	Does this water heater have a sacrificial anode to protect it from corrosion? I am replacing an ariston 2.5 that rusted out very rapidly
Answer:	Yes. I own one. The Kenmore model number is Model 758.154200

• SAFE AND ENVIRONMENTLY:This lectric water heater uses green environmental material, which is qualified for international standard, and satisfies difficulties of hot water supply for multiple places, easily solves issues such as face washing, bathing, vegetable washing and dish washing.
• FULL AUTOMATIC CONTROL: Automatically adding cold water, automatically heating and automatic temperature control
• FOUR SAFETY PROTECTIONS: Multiple safety protection devices for boil dry protection over-temperature protection, electric leakage protection and high hydraulic pressure protection to ensure safety and reliability
• CERAMIC LINER: Anti-rust, anti-corrosion, anti-scale, anti-leakage to extend service life.Simple appearance and firm structure
• SPECIAL PURPOSE SEWAGE OUTFALL: Simple liner cleaning, time-saving and labour-saving. Liner anode protector is mounted at sewage outfall to facilitate checking and replacing anode protection materials

User questions & answers

Question:	Is there a better mixing valve available
Answer:	Sorry, we can not offer a better one now. Hope you can understand.
Question:	how do you mount this? does it come with mounting brackets
Answer:	First measure the position and distance with the scraper on the back, then drill the wall with a 16mm electric drill, and then install the screw to align with the hook.
Question:	What is highest temperature it gets
Answer:	I've only run it up to the next to last setting but its giving me 75 celsius - about 167=68 degrees F.
Question:	can this be mounted on the brackets on the floor and not use the sprayer, and act as a stand alone not water heater
Answer:	Point of service - yes - a sink or a shower. But not a more than one point of service.

Product features

Newest electric water heater solved the problem of not heating

This is a lightweight electric water heater with a perfect combination of inner quality and classical appearance, which applies for multiple demands of different families.

Easy to install

It can be placed in the space exquisitely where is decorated by you elaborately, and embellish your furniture much more wonderfully. It can be installed in the kitchen, rest room, bathroom or any other places you want optionally because of its characteristics of small area, strong applicability and convenient installation.

If you do not know how to install it , we can offer the video!

Product description

FEATURES

Instant hot water comes with powerful 5.5kW heating element, expect hot water for 3 seconds, perfect choice for sinks to provide endless hot water any time.

ENERGY SAVING

This tankless water heater avoids standby heat loss of those bulky storage water heaters, minimize energy waste and achieve 65% energy saving with help of its smart self adjustment technology.

HEALTHY WATER QUALITY

Traditional bulky water tanks store water for long time, causing bacterial growth and rust issue, time to get clean water via a tankless hot water heater. The ECOTOUCH unit separates water and electricity line so as to avoid issue of calcium deposits.

MULTIPLE SAFETY PROTECTIONS

Over temperature protection

Dry heating protection

Leakage protection

Water and electricity line separated

EASY INSTALLATION

Real compact design, water heater cooridates with scenes decor, above sink or under sink water heater, horizontally, vertically or obliquely installation. Comes with easy installation brackets, pipe fitting of 1/2" NPT and 10AWG power cord(fixed to the unit) so you don't to have to hire a plumber even if you can do it.

SPECIFICATIONS

Power: 5.5kW

Voltage: 240V~60Hz

Min. water flow to activate the unit: 0.475GMP

Max tempt rise from 67°F to 109°F @ 1.2GPM

Max. Amperage: 23A

Recommended wire size: 10AWG

Required circuit breaker : 1x 2-Pole 30 AMP

KINDLY NOTE

1.The unit is mainly for sinks, not for shower purpose.

2.The tankless water heater should be installed professionally.

3.Please read instruction manual carefully prior to installation and use!

PACKAGE INCLUDES

1X ECOTOUCH 5.5kW instant water heater

1X Instruction manual

1X Installation accessories

1X Remote control(for Black model)

• 【INSTANT & SUFFICIENT HOT WATER】Applied with 5.5KW heating system, the electric water heater supplies instant, consistent and endless hot water of 116℉or higher temp shortly, no waiting for preheat nor terrible temp up & down, perfect companion for sinks. Time to get rid of those "lukewarm" toys.
• 【SMART SELF ADJUSTMENT】The hot water heater adjusts power input based on flow rate and temp setting in real time. For example, less power will be applied by the system when waterflow reduced, thus you still get ideal temperature instead of scalding hot water, which means comfortable experience. Optimal energy efficiency of 98% saves considerable electric charge.
• 【CONVENIENT USE】The tankless water heater comes with digital display & touch control panel so temp setting is easy job. Now turn on the tap and let the smart unit do the rest, you needn’t go through hard lesson about temp setting by a mixer tap without any hint. The Black model comes with Remote control, useful for installation under sink.
• 【SAFE and DURABLE】Applied with multiple protection devices, every piece goes through strict tests to ensure 100% safe. Inner water and electricity lines are designed to run separately so as to avoid leakage or harm of scale build up. Approval by ETL and qualifies for UL, you can expect outstanding performance for years to come.
• 【POINT of USE】The sleek tankless water heater is compact as an oatmeal box, making it possible to install anywhere close to outlet and avoid energy waste. It can be mounted horizontally, vertically, obliquely, ideal for kitchen, bar, school, hospital, community and hair salon. Please verify it is the right size for you: 5.5kW@240V; dimensions 11" x 7.5" x 2.35"; pipes fittings :1/2" NPT.

User questions & answers

Question:	Unit needs to be reset if power goes out, is this normal? I have to get a ladder out to reset
Answer:	Dear valued customer, Thanks for your trust in ECOTOUCH tankless water heater electric. We would like to clarify that ECOTOUCH tankless water heater turns on automatically when it detects water flow rate . When not in use, the tankless water heater goes into standby mode. If you get any question,please fell free to contact and we will do best to serve and assist. Wish you pleasant day! Best regards Vivian from ECOTOUCH
Question:	Can I take my shower with it
Answer:	Thanks for your message and we are deeply sorry for all the inconvenience that has caused. We fully understand the ECO55 unit does not get sufficient hot water for the shower purpose. If you need to use this water heater for shower, we would like to suggest you that you need to purchase a ECO90 water heater and then install them inline, under this condition, they will serve as a 14.5kW tankless water heater system, sufficient for shower purpose or 2 faucets at the same time. If you need any further assistance,please fell free to contact us and we will do best to serve and help. Rest assured, you will not suffer any loss from dealing with us, because we are a trustworthy company that will stand behind our products always. Wish you pleasant shopping! Best regards. Vivian from ECOTOUCH
Question:	Can this unit be used on a boat? I have a small 27' foot sailboat I would like to replace the older water heater
Answer:	If you have 220 volts on you boat
Question:	What type of fitting fits the intake side? It has a gasket that came with it. This side has a restrictor inside it it and needs somehting flush
Answer:	Dear Customer, Thanks for your trust in ECOTOUCH tankless water heater. You needn't consider about the filter inside the inlet pipe. Pipe connection is the same for both sides. Please use the leak-proof gaskets before you do pipe connection and connect the unit to hose with 1/2NPT connector. If the water quality in this district is not good, so the water must be purified with filter device. And we would like recommend the inlet side can be disconnected, flush to clean the filter periodically. If you have any other question during installation, please feel free contact us via [email protected] any time, we will do our best to help. Wish you pleasant shopping. Vicky from ECOTOUCH

Product features

Electric Tankless Water Heater For Sinks

Being one of those limited choices with smart modulation heating, ECOTOUCH tankless water heater provides instant & endless hot water with optimal thermal efficiency of 98% and minimum energy cost. Thus, the tankless water heater heats up 1.2GPM water from 67℉ to 109℉, which out runs most point use water heaters and will sure cut your electric bill.

Designed with compact size, it is one of perfect solutions for Kitchen & Bathroom Sinks, Wet Bars, Strip Malls, Doctor's Office.

Instant hot water and endless

As soon as you turn it on, hot water comes out immediately with desired temperature and sufficient flow rate of 1-1.5 gallon per minute, no waiting for preheat or standby energy loss. The best part is you get endless hot water now, 24h service, anytime you need. Perfect for sinks.

More hygiene

No storage in bulky water tank for long time heating, avoids bacterial growth and rusting issue that do great harm to water quality. Besides, water pipe and electricity heating are designed to run independently so as to avoid scale build up, now you get steady stream of clean and fresh hot water.

Smart modulation and energy saving

Equipped with a smart modulating control for stable temp, the hot water heater adjusts exact power input according to power calculation based on flow rate and temp setting in real time, which means you get still stable temp, instead of scalding hot, when you reduce flow rate. Optimal energy efficiency is promised.

Sleek & compact design

360 degree installation, lightweight design and compact as an oatmeal box, the tankless hot water heater is capable of and being located near by. It features a sleek and attractive design to blend seamlessly with decor.

Product description

120V - requires hard wiring. 1440W element. Magnesium anode rod. Rectangular shape with 2" of foam insulation. Glass lined tank for longer life. 6 year on heater and 1 year on parts for both commercial and residential use. Temperature/pressure relief valve included. Can be mounted both horizontally or vertically. Mounts on floor or wall. Meets ASHRAE 90. 1. See Info Page for technical and installation specifications.

Manufacturer Contact Information

800-283-3787

• CONVENIENT HOT WATER HEATER: 7 gallon point-of-use mini-tank fits under your sink to provide hot water right where you need it. Thermal efficiency is 98%. Dimensions : 17.5 W x 17.5 H x 14.5 D Inches
• INSTALLED VERTICALLY OR HORIZONTALLY: This larger model can be mounted vertically (7 gal. of water supply) or horizontally (5.1 gal. of water supply)- vertical orientation is installed with the cold and hot lines on top of the unit
• RELIABLE WATER SOURCE: Easily hard-wire the 7-gallon model to provide the on-demand reliable water source your home or office needs
• IMPORTANT INFORMATION: Heating capacity of 1440 watts and a temperature range of 65-145°F max. Operating pressure-150 psi. Water fittings-3/4 inch Male NPT. Electrical requirements (Amp 12A/Volts 120)
• EASILY MOUNTED: Can be shelf, wall or floor mounted (bracket included for vertical orientation only); simply tap into the cold water line and install the water heater directly at the sink to provide hot water

User questions & answers

Question:	What is the recovery time if the 7 gallons of hot water is used
Answer:	I have the 4 gallon tank and it is not too bad for the reheat
Question:	Can I reduce the pipe's size from 3/4 in to 1/2 in without any negative effect on the unit
Answer:	No harm to unit.....Max water flow will be reduced a little.
Question:	Can i use this to replace a small rv hot water heater
Answer:	Yes, but realize that it's electric and draws quite a few amps, most rv water heaters are propane.
Question:	The Manual request for the ES8 a 20 Amp breaker and 12GA wire. The wattage however is 1440 with 12 Amps. Why then 20 Amp breaker and not
Answer:	I would use a 20 amp circuit with 12 ga wire but there are no inrush concerns with a resistive load. A heating element does not have a higher initial current draw like a motor. It draws 1440 watts or 12 amps at 120v. Since 14 ga wire must be fused for 15 amps, this device by itself is already at 80% of the circuit’s capacity.

Product features

Bosch ThermoTechnology

The Bosch Tronic 3000 T point-of-use electric mini-tanks are available in three compact sizes, which can be wall-hung (bracket included) or floor-mounted. They fit easily under a sink, even in a cabinet space, and because they have a sleek and attractive design, they blend in seamlessly with existing decor when installed in a visible location. Simply tap into the cold water line and install the water heater directly at the sink to provide hot water. Great for a wide range of locations!

Water Where You Need It

Provides hot water quickly at point of use and comes with temperature /pressure relief valve installed - 2.5 and 4 gallon tanks feature a simple 120 VAc plug-in connection (1440 watts).

Quality for Long-Life

Thick CFC-free foam insulation for maximum energy efficiency, glass-lined tank for durability.

Great for Small Spaces

Water heaters are compact and lightweight and can be floor, shelf, or wall mounted (except 7 Gallon) - features a sleek and attractive design to blend seamlessly with decor.

Minimize Wait Time for Hot Water

Waiting for hot water at a sink located far from a primary heating source can be frustrating. Only having access to cold water from a sink is just not useful, and plumbing a hot water line to every sink in a home or business requires time and money. To get hot water where it’s needed, when it’s needed, a better solution is to use the Tronic 3000 T from Bosch: a point-of-use electric mini-tank heater. This heater can supplement a primary water heating source, or be used under a single sink. In fact, the Bosch Tronic 3000 T can be used for three different applications: as a sole water heating source for a single sink, as a supplement to an existing heater located far from the sink, and as a buffer installed in-line with tankless water heaters that experience intermittent cold water, also known as 'cold water sandwiching'. No matter the configuration, there’s minimal stand-by loss from this premium mini-tank water heater.

Product description

Professional classic® tankless electric water heaters offer continuous hot water quick and on demand for single point-of-use or multiple applications

• External adjustable digital thermostatic control with LED display (+/1 degree accuracy
• Durable Copper immersion two heating elements, field Serviceable.Self-modulating power control
• Simple installation – 1/2 NPT adapters included; side 1/2 inch Compression water connections
• 99.8% energy efficient. External controls to adjust temperature in increments of 1°f. Water-Saver Shower Head – 1.5 GPM
• Threaded for easy replacement, simple installation, digital temperature display 54 A. 13kW Model Flow Rate: up to 3.17 GPM
• 54 A

User questions & answers

Question:	We have a 500sq' apt. 1 kitchen sink, 1 lav sink and tub/shower. This tankless heats water to both sinks but nothing to the tub/sh. Help
Answer:	Sinks have aerators to slow down the water where a tub doesn't. It sounds like one possibility is that your exceeding the GPM for this heater. Next possibility, double check an measure your actually getting at least 240v at the heater, I had an issue where my unit was only getting 235v an it was causing a similar issue where only one of the two heating elements was activating. I had it set to 125F but it was coming out 100F. It was warm and without a meter I would of thought it was working correctly until I tried filling a tub. It couldn't even get the water warm. I pulled my wires out an restripped an cut an screwed them in an it fixed my problem, now its measuring around 245v. Make sure there is no copper showing after screwing down your input wires. Now filling the tub I noticed after about 10-15 seconds the water gets too hot to touch. I set it to 135F.
Question:	Do these tankless water heaters require an overflow line to the outside of the home or a pan like is required on normal water heaters
Answer:	No tank, so, no overflow line required. It mounts on the wall. A pan is needed if required by building code in your city.
Question:	what are the wiring and power requirements
Answer:	good morning,60 amp breaker and , number 6 cable !thank you have a great day!
Question:	How many amps are needed for rheem rtex - 13 240v heating tankless electric water heater
Answer:	Hello-The RTEX-13 requires 1x 60A@240V breaker / 6 AWG recommended wire size.Specs - http://cdn.globalimageserver.com/fetchdocument-rh.aspx?name=Specification-Sheet&id=fc3235b7-7cd0-42cd-93bc-7169ea92be31 Rheem 800-432-8373I hope this helped :)Ben

Product features

About Us

Brothers Richard and Donald Rheem founded Rheem Manufacturing Company in Emeryville, CA, in 1925. While the company has produced a number of products in its nearly 100 years of operation, Rheem is currently the manufacturer that produces heating, cooling, water heating, pool & spa heating and commercial refrigeration products, and it is one of the largest manufacturer of water heating products in North America.

Product description

A world leader in designing, engineering, and manufacturing appliances and hardware for RV industry for over 30 years.

• Includes base rails and Custom designed mounting brackets and hardware
• Package Dimensions: 10.16 H x 1.27 L x 8.89 W (centimetres)
• Package Weight: 0.045 kilograms
• Country of Origin : China

User questions & answers

Question:	the this kit have 4rings and 2gasgets
Answer:	Yes 4 rings to mount pan back to the tank, and the 2 ea gaskets for the pop-off valve, and drain plug bosses. Worked great i started the rings back on with a 2.5 hole saw then drove them the rest of the way with a split piece of pvc pipe.

Product description

40 gallon, electric, medium, dual 5500W, 240V elements, 3" insulation, 95 energy factor, recovery at a 90 degrees rise-gallons/hours 25, first hour rating 56, t & p valve, pex polymer lined heat trap nipples, pex dip tube, glass lined tank, duel mag anode rod, unit dimensions: 22"d x 50"h, 12 year tank & parts warranty, meets new naeca 2015 efficiency standards.

• Pex polymer lined heat trap nipples
• Aluminum anode rod
• 95 energy factor
• Model number: 6-30-EOLBS 100

User questions & answers

Question:	Is this 110volts
Answer:	No. It's 220/240 volts.
Question:	It's this 30 or 40 gallon? Discription and title disagree
Answer:	The one they sent me is 30 gallons. Dented up and ugly, but 30 gallons.
Question:	Is this 30 gallon or 40 gallon
Answer:	"RELIANCE WATER HEATER CO 6-30-EOLBS 100 30 gallon Electric Water Heater" 30 gallons.

Product description

Be prepared!

• Stores 50 Gallons of water
• Made in the USA with durable BPA Free plastic
• Made to last & is stackable!

Keep your water stored safely! The BPA free , UV Resistant tank won't harm your drinking water. Buy more than one and be prepared now! Are you a prepper? This is the perfect addition to your preparedness plan!

• BE PREPARED, STORE YOUR WATER! This 50 gallon water storage tank will ensure you're prepared for emergencies during natural disasters and water shortages.
• PROUDLY MADE IN THE USA! These tanks are made in the USA and are made of high density, durable plastic.
• KEEP YOUR STORED WATER SAFE- BPA Free and UV resistant, these tanks are made to last and won't harm you when drinking the water.
• STACKABLE, PREPARE WITH MORE THAN JUST ONE- These tanks are stackable and durable, great for saving space!

User questions & answers

Question:	How many can be stacked together
Answer:	Due to water weight, 2 is the optimal amount to stack.
Question:	Are these tanks nsf approved
Answer:	Yes, we use materials that are FDA and NSF approved or compliant. The base material is NSF compliant.
Question:	Stated height is 30". I am wondering if when stacked a bit of the height is overlapped with those triangle shapes? I need stacked to be
Answer:	The top of the bottom tank (the triangles) does nest inside the bottom of the top tank. Together they are just under 59". Thanks!
Question:	There is nothing in the container (no symbols) to indicate bpa free and uv resistant. are they
Answer:	Yes, the tanks are BPA free & UV resistant. Markings are not required or typically used in regards to water storage. Our tanks are manufactured in the USA. We use a linear low density polyethylene that is BPA free. We do have documentation to support this & will gladly send it to you. If you would like a copy, please send us an email. Thanks!

Product description

606 series. 1650/120V. UL listed. No dip tube since the bottom inlet eliminates need for it. 1" foam insulation/16.00 R-value. Factory installed T&P valve. Meets NAECA codes. Glass lined tank. Inlet and outlet connections on side for easier installation in tight spaces. Warranty: 6 year tank/parts.

From the Manufacturer

Series 606 electrics provide up to 4,500 watts/hr. input — plenty for all your hot water needs.

• Provides secure connections to components and lines

User questions & answers

Question:	What tools are required for installation
Answer:	The only tools needed are a Pipe Wrench and Screw Driver and TWO Wire Screws. I used my old OFF/ON switch and that's all the info I can pass on. Good Luck with your Project.
Question:	How many amps does this draw
Answer:	mine is on 20 amp breaker with #12 wire. That is a maximum amp rating on tank. It runs on much lower amperage. Probably in middle of that 20 amp max.
Question:	Does it supply enough hot water to wash dishes? could it deliver enough hot water to take a shower
Answer:	Yes to both, a water saver shower head and sensible showers. You can;t stay in there for an hour.
Question:	the dimensions say 20x18.8x33.5 what is the
Answer:	Mine is 24.5 inches High and 18 inches Round. I'm sorry but I don't know what the 33.5 is for.

Product description

Stiebel Eltron SHC series mini-tank electric water heater is ideal for office buildings, stores, malls, warehouses, food trucks, restaurants, gas stations, schools, hotels/motels, commercial, industrial and institutional. residential: bathroom sinks, kitchen sinks, rvs, cabins/cottages, low flow showers and laundry areas. An SHC mini-tank frees up precious space while providing plenty of hot water for hand washing or kitchen applications. Plumbed with cold water and used as a stand-alone supply of hot water, or plumbed with hot water from a remote tank to minimize delays, an SHC always delivers hot water when needed. By put - ting hot water right where it is used, pipe runs are minimized and water and energy use reduced. The smaller tank coupled with superb insulation reduces stand-by losses especially when compared with larger tank-type water heaters. With its flat back and included bracket an SHC easily mounts right under or near the sink. Once filled with water it simply plugs into a 120 V outlet. With only an 11 amp current draw, no special wiring is required. Lightweight and compact, the SHC saves space, quickly provides hot water right where it is needed. Certified to ANSI/UL Std. 174 Conforms to CAN/CSA Std. 22.2 No. 110. Tested and certified by WQA against NSF/ANSI 372 for lead free compliance. ISO 9001 certified. Technical Specification: Phase - 60/50 Hz: single; Voltage: 120 V; Wattage: 1300 W; Amperage: 11.3 A; Nominal water volume: 2.65 gal / 10 l; Weight empty: 15.9 lb / 7.2 kg; Height (includes PandT valve): 18-11/16" / 475 mm; Width: 11" / 280 mm; Depth: 10-5/8" / 270 mm; Maximum operating pressure: 150 psi / 10 bar; Maximum adjustable temperature: 140 degrees F / 60 degrees C; Recovery time: 18 minutes; Standby energy loss @ 131°F / 55°C: 0.37 kWh / day; Water connections: black steel -1/2" NPT.

From the Manufacturer

The SHC Mini-tank frees up precious space while providing plenty of hot water for hand washing or kitchen type applications. Why store 30 or more gallons of hot water when 2.5 gallons are sufficient for the job?

• Plugs into standard 120 volt outlet
• T and P valve included
• Wall-mounted with included bracket
• Glass-lined tank and fast recovery
• 6-Year warranty on tank

User questions & answers

Question:	How long does it take to heat the (cold) water in the tank if power to the unit has been shut-off for a period
Answer:	The spec in the manual says the recovery time is 18 min. But mine seems faster than that. I have not timed it but it is not slow. Seems to me it is around 5-10 minutes to fully heat up.
Question:	anyone wish theyd bought the 4gal or the 2.5 is more than enough for light use
Answer:	I live off grid and use a hose with garden sprayer to shower so my use is about 3 gal. per shower and the unit is awesome, but if you are going to use it for a regular shower go to the 4 but for sinks or anything else it will get the job done!!!
Question:	Will this fit under a bathroom lavatory sink?? 26.5 inches tall and 16 inches wide
Answer:	It probably will. Installed, ours takes up a total of 14" wide by 24" tall including the pipes on top and down one side. It is also hanging on the wall with 1" space between the bottom of the heater and the base of the inside of the cabinet. Hope this helps.
Question:	Can the unit be hard wired instead of being plugged into an outlet
Answer:	I suppose so, but if that's your plan and you're not an electrician, you should hire one. I would take the unit apart, and replace the cord with #12 NM or BX depending on your local jurisdiction. Because it draws about 11 amps (120v), I would put it on a separate breaker

Product features

Delivers hot water almost instantly

Stiebel Eltron SHC mini-tanks are made in Germany. They are designed to put hot water right where you need it for fast, convenient, water-and energy-saving use. The sleek, attractive European design complements any decor whether it is exposed to view or hidden under a sink. Plumbed with cold water and used as a stand-alone hot water supply, or plumbed with hot water from a remote tank as a buffer tank to minimize delays, an SHC always delivers hot water when needed.

Easy installation plus saves water and electricity

All three popular sizes simply plug into a standard 120 volt outlet for easy installation. By putting hot water right where it is used, pipe runs are minimized and water and energy use are reduced. The small tank with its world-class insulation and the lowest stand-by losses in the industry saves you money all day, every day by reducing energy needs. Why go to the hassle and expense of installing a large tank when 2½, 4 , or 6 gallons will do?

Stiebel Eltron is known for high quality products, and the SHC is no exception.

Flat Back & Easy Installation

The flat back makes easy, space-saving installation whether mounted on a wall with the included bracket or just sitting on the floor. P&T valve is factory installed.

Plugs into a 110/120 V outlet

With only an 11 amp current draw, no special wiring is required. Fill any SHC mini-tank with water then simply plug it right into a standard electric outlet with the factory-installed power cord & plug.

Convenient temperature adjustment

The simple thermostat dial is conveniently located on the top for easy for temperature adjustment from 86-140 °F. A special frost protection setting can be selected to maintain internal tank temperature above freezing.

Get hot water fast

Whether used as a stand-alone supply of hot water, or plumbed inline with a remote tank, an SHC delivers hot water almost instantly for water-saving & energy-saving comfort wherever hot water is needed.

Product description

It is important that you fully understand all product details, including the water pressure before you purchase this washer. 1.This washer is powered by 12V DC, thus the water pressure is only 260psi maximum, even though our washer pressure is 3x higher than any other 12V pressure washer on the market, it is still less water pressure compared to higher voltage pressure washers. If you prefer to have a super strong pressure washer, the 40V portable washer or 110V home powered washers would be a better choice. 2.A FULLY charged battery (for safety, a full charge time for the battery is designed to take 4-6 hours) can run NONSTOP at HIGH PRESSURE mode for 25 minutes plus. Because of the Total Stop System, the pump only runs when the trigger is operated, so it saves battery power, as well as saving water. 3.The water chamber lid is not fully sealed, the washer should not be move too fast to avoid spillage. 4.This washer should not be placed in your trunk if you plan to move your vehicle, such transportation is dangerous because water has very strong inertia force and cause the washer to topple over. 5.The washer is pulled by a durable nylon strap. 6 Clean water only. This patented CarAid 9909 Pressure Washer is specifically designed as an all-in-one, multi-purpose washer, no garden hose is needed and no AC power is required. It’s also environmentally friendly and saves 30% more water than a regular pressure washer. 1-year manufactory warranty plus CarAid promise to Amazon customers for 2 additional years of warranty extension.

• FOLDABLE WATER TANK: The expandable chamber can hold up to 9.25 gallons water;
• POWERFUL MOTOR: Powerful 12V/150-Watt motor generates 260 psi of water pressure, which is three times higher than any existing 12 Volt washers on the market;
• MULTIPLE POWER OPTIONS: Built-In 4000 mAh Lithium Battery or Power Via Car Lighter Aux Port (Plugs Included), and it can also be powered by a home converter (Purchase separately);
• EXTENDED BRUSH: It comes with three 18-inch wands for brush extension, and soap dispenser built into the brush handle;
• Please read all product details below to help you decide whether this washer is right for you.

User questions & answers

Question:	do i need to get a home power adapter
Answer:	No, you do not need to get a home power adapter. This machine comes with Built-In Battery, and also including a Car Lighter Aux Port Plugs cord ( for connecting to a vehicle battery).
Question:	Can I connect a regular garden hose to it using it in low pressure mode? What adapter do I need
Answer:	We are sorry, you can't and there is no connection for garden hose.
Question:	Is it only the car charger for this or can i get a wall plug in for this? and please identify where an name of charger
Answer:	It comes with both a car power outlet plug and a home wall charger. However, the car plug only powers the unit, it will not charge the unit's battery but the included wall charger does actually charge the battery
Question:	How much water hold
Answer:	The expandable chamber can hold up to 9.25 gallons water.