13 best skb acoustic guitar pickups

Product description

For decades, SKB has been the most innovative manufacturer of top-quality cases and accessories. Famous for their unwavering attention to quality and detail, purchasing an SKB case is sure to provide the most service life of any case on the market. So much so...That SKB offers their limited lifetime Warranty on their cases. Buy SKB...Buy with confidence. 3I Series injection molded waterproof cases are constructed of Ultra high-strength polypropylene copolymer resin and feature a gasketed, waterproof and airtight, submersible design (IP67) that is resistant to corrosion and impact damage. Its continuous Molded-in hinge, patented "trigger release" Latch system with TSA recognized and accepted locks, four reinforced locking loops for customer supplied locks, comfortable, snap-down rubber over-molded cushion grip handles, secure stacking, and automatic ambient pressure equalization valve (mil-stud-648c) all contribute to its military grade design.

• Tsa latches
• Designed to fit most acoustic guitars
• Quality injection molded manufacturing

User questions & answers

Question:	Im looking to take my Ovation mid-depth bowl guitar on an airline and a ship. Will this work
Answer:	If your goal is to keep the guitar safe from weather changes, it should be fine. If you are using it as a flight case, I would guess it will be okay. Molded cases are a little iffy for this function as latches break without too much of an obvious cause. My flight case is not molded plastic for this reason.
Question:	My guitar is 4.75" deep at the very bottom. the skb website says this case is for 4.5" deep guitars. is there any chance my guitar will fit this case
Answer:	It fits My D28 Martin just fine. I wouldn't risk forcing Your Guitar into the SKB because THE SKB is designed for Dreadnaught Type Guitars.
Question:	Is this a flight case? Is it waterproof rated
Answer:	It is a flight case and waterproof. Your guitar will not be damaged in this case
Question:	This case too is for 12 strings acoustic guitar
Answer:	As long as the body fits in the dimensions it should be good. I don't have a 12 string so the headstock may be long but with my taylor and acoustic composite the headstock sits in with a little bit of room left on the top.

Product features

iSeries from SKB!

SKB iSeries Injection Molded Mil-Standard Waterproof Cases are molded of ultra high-strength polypropylene copolymer resin and feature a gasket-sealed, water- and dust-tight, submersible design.

The iSeries offers maximum protection for your valuable items. Many sizes and configurations are available. iSeries products offer the famous SKB Lifetime Warranty!

Built for Maximum Performance

SKB iSeries Injection Molded Mil-Standard Waterproof Cases are molded of ultra high-strength polypropylene copolymer resin and feature a gasket-sealed, water- and dust-tight, submersible design . Standard features also include a molded-in hinge, patented trigger release latch system, comfortable, snap-down rubber over-molded cushion grip handles, automatic ambient pressure equalization valve and resistance to UV, solvents, corrosion, fungus, and impact damage.

Patented Latch System

iSeries cases feature the Patented latch system made famous by SKB. Models equipped with locks are TSA compatible.

Durable and Comfortable Handles

Handles are extra tough. Also, they features comfortable over-molded padded handles.

Protective Ambient Pressure Relief Valve

Automatic ambient pressure equalization valve), and resistance to UV, solvents, corrosion, fungus, and impact damage.

Product description

Electric Guitar Soft Case with EPS foam interior/Nylon exterior, back straps



Specifications       

       

Interior Length    39.25 in  - 99.70 cm

Exterior Length    40.50 in  - 102.87 cm

Exterior Width    14.50 in   -  36.83 cm

Exterior Depth    6.00 in - 15.24 cm

Instrument Body Length - 16.50 in    41.91 cm

Instrument Body Depth  -  2.75 in    6.99 cm

Instrument Lower Bout  -  12.75 in    32.39 cm

Instrument Upper Bout  -  11.00 in    27.94 cm

• Designed to fit traditional body style guitars, including left-and-right hand models
• The
• Heavy-duty double pull zipper Molded EPS interior with plush lining
• Durable 600-denier exterior layered with rigid foam 2 convenient exterior accessory pouches

User questions & answers

Question:	does it fit an ibanez ar 420? thanks
Answer:	i bought it for my BC Rich Warlock and it fits perfectly so i guess there shouldn't be a problem with your guitar. Enjoy!
Question:	Will this case fit an epiphone g400 sg-type guitar
Answer:	Not sure about fit but I would tend towards a hardshell case with the neck and headstock on a Gibson style instrument. I would hate to break the neck and these cases aren't very deep.Also I did post a follow up review stating I was having issues with the zipper so I'm about through recommending this case to people. Mine might be a one off problem but I don't even use this case for transport, just storage, and it still went bad.Why not go with a hard shell from Epiphone they're only about $20.00 more.
Question:	Do the backpack straps come off or tuck away
Answer:	No ....they are permanently sown on and do not tuck away but, pull tight against the back to stay out of the way.
Question:	Will this fit a G&L tribute legacy
Answer:	I don't know. I have a Fender Telecaster and it fits perfectly.

Product description

Baby Taylor/Martin LX guitar shaped hard-shell.

• Interior Dimensions - 34.5"L x Instrument Body L - 16" Depth - 4.25" Lower Bout - 12.5" Upper Bout 9.25
• Molded in bumpers
• Full length neck support
• Plush lined rigid EPS foam interiors protect instruments

User questions & answers

Question:	Will this fit dean SKY acoustic
Answer:	I don't know. I don't sell it. I bought one for my baby Martin, which fits perfectly in it. Ask the seller.
Question:	Will it fit a baby Taylor Koa electric acoustic guitar
Answer:	While I can't speak about the Baby Taylor, it fits my Mini Martin like a glove. Did not fit my Ibenez Tenor guitar. Very sturdy, well built case.
Question:	Does this case fit a Martin Ed Sheeran
Answer:	Yes, as this is the small Martin.
Question:	Will Taylor Big Baby fit in it
Answer:	No. A baby taylor Martin fits very snug. Not enough room for anything bigger.

• ★ FITS in soundholes from 3.88” (98.5 mm) to 3.94” (100mm) diameter. ★ HIGH impedance passive design, no battery required.
• ★ BUILT with Customized Rare Earth Neodymium Magnet and Single Coil with Handwound Oxygen-Free Copper.
• ★ SOLID Beech Wood Housing for better transmission of Acoustic Vibrations with Super String Balance and Pure Acoustic Clarity.
• ★ CAME with Customized Studio Grade Lossless Transmission Audio Cable.
• ★ QUICK Installation and Storage, no drilling required, harmless for guitars. ★ DOES not work with nylon guitar strings but only works with steel-string acoustic guitars. ★ DOES not work with 3/4-size guitars like Taylor Baby, Little Martin series.

User questions & answers

Question:	will this work on a vintage ovation balladeer without drilling
Answer:	You can't drill a hole in your vintage ovation balladeer. Because the back of the guitar is not made from wood but a composite material. We suggest purchasing NEO-SP30 soundhole pickup or SBT-10 soundboard transducer for your guitar. And please note NEO-SP30 only fit for steel-string acoustic guitars whose soundhole diameter is between 3.82" to 4.33".
Question:	Can I connect this to a loop pedal
Answer:	Yes, you can connect to the loop pedal and then to the amplifier.
Question:	Do I need to loosen the strings to insert it
Answer:	Usually, there is no need to loosen the strings for installation. But if your guitar soundhole diameter is as close to the minimum size that we described (3.82” to 4.33”) or your string is too tight to get through, and it’s not so easy to install the pickup on your guitar, we recommend to loosen the strings for easier installation.
Question:	Can this pickup detect guitar drumming ( hitting the guitar body to make it sound like a drum
Answer:	Yes, it can detect the tapping sound. But the tapping sound from Amumu NEO-SP30/31 is not as big as the sound from Amumu SBT-10 because SBT-10 is a vibration transducing pickup which transduces all the signal from the soundboard and the body. We suggest you try Amumu SBT-10

• Volume adjustable, with a control knob
• Fit for most of instrument, such as guitar, ukulele, violin, etc.
• Easy to install, can be sticked near sound hole with self-adhensive, which can be reused
• Mini design, comes with 10 ft amplifier cable(standard 1/4" connector) and 4 x stickers
• Good/clear/crisp sound quality, away from squeal feedback

User questions & answers

Question:	Do I need an app to connect it to my phone and record the audio
Answer:	no, it's straight analog. 1/3" jack gets plugged into a mixer or amplifier. very good quality
Question:	Will this work for an autoharp
Answer:	Autoharp is a box and string instrument and I believe there will be no problem to use Luvay Piezo pickup with it. I have not seen or played Autoharp, but just googled and looked at it and it looks like a guitar with out a neck, so this item can work with it. Good luck!
Question:	How long is the cord
Answer:	10 ft
Question:	Will this work for nylon strings
Answer:	Yes. It will work on any string instrument, included nylon strings

Product features

Application method ①

Application method ②

Product description

SKB I Series injection molded Mil-Standard waterproof cases are molded of ultra high-strength polypropylene copolymer resin, featuring a gasket sealed, water and dust tight, submersible design (MIL-C-4150J/ IP67) that is resistant to corrosion and impact damage. Features a molded-in hinge, patented trigger release latch system, comfortable, snap-down rubber over-molded cushion grip handle, automatic ambient pressure equalization valve (MIL-STD-648C), resistance to UV, solvents, corrosion, fungus and impact damage (MIL-STD-810F).

• Waterproof and dust tight design (mil-c-4150j).
• Trigger release latch system
• Ambient pressure equalization valve (MIL-STD-648C).
• In-line skate style wheels for easy Transport.
• Unconditional Lifetime

User questions & answers

Question:	Is the foam pick and pluck apart or solid pieces on the interior
Answer:	The foam is not pick and pluck. There are four separate solid layers in the body of the case. The bottom layer is a base layer 0.5 inches thick. The next one up is 1.5 inches thick. Then two more layers on top each 2.0 inches.
Question:	What are the inside dimensions
Answer:	According to the Manufacturer's Rep: "The model number has the interior dimensions. This is true for all 3i versions of SKB cases. So the 3i-4719-8B-L is 47” long by 19” wide by 8” high."
Question:	Let me know the carton size of skb4719, please. Is long side over 50inches
Answer:	Hi. Are you asking about the size of the carton box, where the skb is delivered from the production factory? If it is this size I would say 2 inches bigger in length, width and depth, than the size of the skb case. But I can’t tell you exactly. I threw it away after arrival.

Product features

iSeries from SKB!

SKB iSeries Injection Molded Mil-Standard Waterproof Cases are molded of ultra high-strength polypropylene copolymer resin and feature a gasket-sealed, water- and dust-tight, submersible design.

The iSeries offers maximum protection for your valuable items. Many sizes and configurations are available. iSeries products offer the famous SKB Lifetime Warranty!

Built for Maximum Performance

SKB iSeries Injection Molded Mil-Standard Waterproof Cases are molded of ultra high-strength polypropylene copolymer resin and feature a gasket-sealed, water- and dust-tight, submersible design . Standard features also include a molded-in hinge, patented trigger release latch system, comfortable, snap-down rubber over-molded cushion grip handles, automatic ambient pressure equalization valve and resistance to UV, solvents, corrosion, fungus, and impact damage.

Patented Latch System

iSeries cases feature the Patented latch system made famous by SKB. Models equipped with locks are TSA compatible.

Durable and Comfortable Handles

Handles are extra tough. Also, they features comfortable over-molded padded handles.

Protective Ambient Pressure Relief Valve

Automatic ambient pressure equalization valve), and resistance to UV, solvents, corrosion, fungus, and impact damage.

Product description

The SKB 1SKB-GSM is designed to fit the Taylor GSM mini guitar with full length neck support to cradle neck. The exterior includes molded-in bumpers to provide valance protection, Heavy duty deluxe Plush Interior and TSA recognized and accepted locks.

• Molded in bumpers
• Full length neck support
• Plush lined rigid EPS foam interiors protect instruments
• Reinforced nylon trigger release latching system
• Indestructible cushioned rubber over-molded handle.Bumper protected valance

User questions & answers

Question:	Classical guitar cordoba c
Answer:	How the Hell should I know? I didn’t sell it!
Question:	Does anyone know if a Martin 00-28 will fit in this case and if not does anyone have any recommendations for a molded hard shell case that would
Answer:	Ask the person who sold them.
Question:	Will this case fit the new taylor mini gs bass guitar? i am looking for a hard case that will fit this new bass guitar
Answer:	I have no idea. You need to contact the seller. Amazon always sends these questions. I didn’t sell it.
Question:	Does this case cover broken latches by airlines
Answer:	What are you talking about?

Product description

Features:

- Acoustic guitar pickup with 12-hole magnetic transducer, can capture vibrations quickly.

- Designed with a tone and volume controller for more accurate pickup.

- Produce a clean quality sound and has low feedback.

- Padded clip guards against damaging to your guitar.

- Easy to install, put pickup into sound hole and adjust padded metal piece.

- No need to drill hole and no scratch to your guitar.

- Suitable for 38"-41" guitars with steel strings.

- Comes with an audio cable (3.5mm to 6.35mm plug) for connecting to guitar speaker.

- Pickup Size: 8.6 x 1.1 x 0.4"; Amp cable Length: 9.8ft.

Package Contents:

1 * Pickup (with volume & tone controller)

1 * Audio Cable

• Suitable for for any acoustic guitar that has a sound hole and steel strings.
• Easy-to-use 12 hole magnetic acoustic guitar soundhole pickup is a great music accessory for amplifying your guitar's sound.
• Designed with tone and volume control for more accurate pickup, also supplied with an amp connection cable and jack.
• Produce a clean quality sound and has low feedback. Felt backed clip protects the guitar from any scratch or damage.
• Easy install, just plug the pickup into the point and clip the left side of the point, and then use the wrench to tight up right side of the point , connect the wire from the bottom of guitar to an amplifier and speaker.

User questions & answers

Question:	Any suggestions for guitar speaker that goes well with this
Answer:	I use one of these on my 12-string acoustic. I am very happy with it - the sound awesome.
Question:	Is the jack in the pickup 1/4” so I can use a higher quality cable
Answer:	There is no volume control on the pickup. Volume will be controlled by the amp.
Question:	Hmmmmm I wondering if I could use 2 of these on one Guitar, how would that work out
Answer:	No preamp/Di Box is needed if you plug directly to any amp. If you want to plug directly to the soundboard then, yes.
Question:	Does this item need batteries
Answer:	no, needs a preamp.

Product description

Designed specifically for steel-string guitar the SG-1 offers a players an unobtrusive option to amplify their steel string guitar. Not only is it discreet but the SG-1 also ensures the natural amplification of the instrument without modification. Held in place by tuned strings, SG-1 installs safely and securely between the bridge saddle and pins. SG-1 may remain installed when not in use. Comes complete with a detachable 1/8'' to 1/4'' cable. Handcrafted in Europe.

• Delivers the natural sound of your steel-string guitar
• No modification your instrument necessary
• Wooden sensor casing is lightweight and unobtrusive
• Detachable, or may remain when not in use
• Include 8' detachable cable

User questions & answers

Question:	Will it work on a guitar thats 3/4 size
Answer:	I would assume the bridge on a 3/4 size guitar is about the same as on a full sized instrument. That being said I returned the SG-1 because it sounded horrible and didn't fit my OMC28 Martin. You might want to try the AP-2. They sound better but not much. The down side is they use removable putty to attach to the guitar which might mar the finish over time so I returned that one too. Hope this helps you out.
Question:	how much can it be trimmed to fit between pins and saddle
Answer:	No, it shouldn't need to be trimmed. I have a Guild D55 and it fit nicely and sounded fine. However, it is rather delicate. The piece where you plug into broke off so you have to be careful.
Question:	How thick is the wooden portion that slips under your he strings
Answer:	Mine is about 1/16
Question:	Will this pickup work on a Tacoma Roadking? The bridge does not have pins
Answer:	I've measured and the pickup is about 8mm (9/32 of an inch) at it's widest point at the high E string. Without pins in your guitar, I think you will have to measure your guitar to see if it will fit between the saddle and where the strings go into the bridge. And you might contact KNA directly with your question.

Product description

Onown Pickup Wiring Kit PIckup Piezo 50mm Sensitive Transducer Pickups Prewired Amplifier with 6.35mm Output Jack for Cigar Box Guitars and Acoustic Instruments



It is very large and can collect a wider range of sound in case you are not sure where are the best parts of the sounds.



This is a pre-wired, pre-soldered piezo and jack harness which make it easy for you. All you have to do is to attach the piezo in or on your build, drill a hole and mount the jack. Then you're done!



Installation instruction:

1. Take the plastic film down from the back of transducer to expose the adhesive

2. Place the transducer through the sound hole to the lower part of the front body where the guitar produces the best tonal response

3. Drill a hole from inside the body, loosen the end-pin jack nut, insert it to the hole and tighten the nut The above procedures depend on different instruments.

Specifications:

Material: Metal & Piezoelectric Ceramic Sensor

Color: Shown as Pictures

Sensor Diameter: Approx. 50mm/1.96inch

Interface Diameter: Approx. 6.35mm/0.25inch

Cable Length: Approx. 35cm/13.7inch

Weight: Approx. 27g

• Ensure great tone: pickup piezo transducer with metal material body will enhance the sound of your guitar or ukulele with the advantage of being able to eliminate interfering external sounds and not be influenced by sound reflections from nearby objects, give it a purer acoustic tone.
• No soldering required, just drill two hole for the jack glue on the piezo.
• Perfect replacement: nice replacement part for your instrument. Which fit for most string music instruments such as Guitar Mandolin Cigar box Guitar Violin Ukulele Banjo, etc. Great accessory for guitar enthusiasts.
• Premium material: made of high quality material, which is wear-resistant, durable and also eco-friendly with exquisite design and workmanship.
• Large piezo has double stick tape mounted,works great.

User questions & answers

Question:	Is this wired up and ready to install
Answer:	Yes, you only have to drill a couple of holes for the volume knob and the plug receptacle for the cable. Then attach the piezo pick-up. I use them all the time on my CBG s
Question:	There was a square plastic piece that came with the pick up. What is this for
Answer:	I'm sorry but it has been a while since I installed this in my daughters cigar box guitar. Is it big enough to cover one of the inputs to provide protection? I don't remember that plastic piece in my kit.
Question:	What is the resistance range of the potentiometer that’s included
Answer:	Not sure of the technical aspects of the volume control . but it's loud enough to get me quite allot of " RESITANCE " FROM MY ROOMMATES AND NEIGHBORS! CONTACT MANUFACTUER WOULD BE A GOOD START .GOOD LUCK WITH YOUR PRODJECT!
Question:	Do you have to ground the strings with this pickup
Answer:	You don't have to it work without it but personally I would do so .I build CBGs and just use foil tape as a grounding point! Good luck !

Product description

NEW - Strat/Tele Shaped Electric Guitar Soft case with EPS foam interior/Nylon exterior, back straps

• Designed for Strat/Tele - shaped guitars Heavy-duty double pull zipper Molded EPS interior with plush lining
• Durable 600-denier exterior layered with rigid foam2 convenient exterior accessory pouches
• Carrying handle and padded backpack straps Rubber feet for standing on its side

User questions & answers

Question:	Does this case come with a warranty
Answer:	Yes, SKB warranties their products for a year from the date of purchase against manufacturer defects.
Question:	What's the weight of this gig bag when empty? Thank you
Answer:	No clue, but it's very light. This is my 2nd one. I love these cases! I have a Strat in one and a PRS in the other.
Question:	Greetings, does this liner fit an Epiphone Les Paul
Answer:	Made expressly to fit Fender Strats and Telecasters, and tightly at that. I have not tried an LP in it but those instruments are not really very similar in size and I’ve never seen one fit in a case specifically designed for the other. The fit of a Fender flat headstock vs. Gibson angle headstock would be of particular concern.
Question:	Will this fit a fender mustang
Answer:	Yes, a Fender Mustang guitar will fit. The mustang bass is short scale, but still too long for this case.

Product description

Features:

100% brand new and high quality

Has reinforced braided steel cable

High sensitivity transducer style piezo pickup

Rod Piezo designed for 6-string guitars,can be cut shorter

A great way to add a pickup to your acoustic guitar

It can be cut off for wiring direct to jack

Ideal for acoustic guitars



Package Include:

1pcs 6 Strings Guitar Piezo Pickup



Note:

Please measure and check your guitar size and specifications before purchase, the piezo pickup is not suitable for all guitars.If you're not 100% satisfied with your purchase,please feel free to contact us,we'll refund your money no questions asked within 30 days.

• Can be used on most acoustic guitar, fit for 6 strings acoustic guitar
• Easy to install,no soldering required
• A great way to add a pickup to your acoustic guitar
• 12" lead with 2.5mm plug, which can be cut off for wiring direct to jack
• 100% high quality and like the picture shown

User questions & answers

Question:	is this supposed to replace the guitar saddle on the bridge
Answer:	This doesn’t replace the saddle. It’s supposed to sit under the saddle. You need a tall enough addle so you have room to sand the saddle down to compensate for the thickness of the pickup.
Question:	How wide is the pickup
Answer:	As wide as the bridge or so.
Question:	I am ooking for a flat (not round) piezo to replace a fishman matrix elements piezo which is flat and narrow. will this be a good substitute
Answer:	The one side is flat, the other has ridges, which you can just make out in the picture. Those ridges roughly correspond to the string spacing, almost as though it was intended to be a bridge.
Question:	Can i cut the pickup shorter
Answer:	The entire pickup has an outer jacket so I can't tell. My suspicion is that you cannot. Also would depends on how much you need to take off. Sliver off end of need to cut it down to 4 strings or something.

Product description

For acoustic guitar and most of classical guitar

Easy to use and carry

Size: approx. 69 x 2.8 x 1.6mm

Cord Length: approx. 31mm

Package Including:

1 x Piezo

• For acoustic guitar and most of classical guitar
• Easy to use and carry
• Size: approx. 69 x 2.8 x 1.6mm
• Cord Length: approx. 31mm
• Package Including:1 x Piezo

User questions & answers

Question:	What size is it
Answer:	Measure the slot in the bridge .that will tell you what size you need. Most are all the same unless the slot is a different length
Question:	would this work with a shadow preamp, epiphone? i need to replace the pick up in it
Answer:	The pickup itself should work just fine. The question lies in whether the jack on this unit will be the right one for your preamp. If you're handy with a soldering iron, you could get the correct jack from your old pickup or a new one from Radio Shack and attach it yourself. Just make sure it's shielded or you'll get interference in your signal.
Question:	I am looking for a flat (not rounded) piezo under saddle to replace my fishman matrix elements piezo which is flat and narrow. will this pickup work
Answer:	TMI - It's appears to be ~$100 cheaper than the actual replacement part (Fishman Acoustic Matrix Pickup, Narrow Format by Fishman on Amazon) so it might be worth a try. No site I found including Fishman gives the specific measurements of all 3 aspects of the original - l x w x h. The replacement appears to be slightly longer which might not be a problem. If it fits it will likely "work" but at what cost? Volume difference, change in string height, etc.? I ordered several different cheap p/u's (for a used $150 classical guitar that required a very long p/u) as none were exact, and just kept the ones that did not fit. I'm sure a few could have been returned. It was a $3 p/u that worked in the end but there is some volume loss. This in turn worked out as I have more range to work with on the volume knob before it is too loud or gritty, so it is easier to adjust on the fly in mid-song without over or undershooting. This might lead to tone loss, but subtle if it has. The strings also sit lower, but this did not cause string-buzz or impact the sound much so another misfitting that was fortuitous. Still, most folks would be much better off paying the higher price for the true replacement part as "dumb luck" like this is rare and most guitars are too nice to tinker with just for curiosity sake. Way TMI - If you do attempt to "experiment", first measure the length, width, and height/depth of the p/u you are replacing. If it is too tall or short it will change your bridge height which will likely suck things up playing and even sound-wise. If it is too long it won't fit, too short it won't have even/balanced volume from strings where it runs short. Too wide and it won't fit in the saddle. Next, eyeball the hole under your bridge to see if it will go through. Mine did not fit, but it was close so I hollowed it out a bit more. Then make sure the "output plug" is the right length, There are 2 common sizes - a short and a long. The site notes the 2.5mm is "standard" and I think that is the longer one, the other being maybe 1.8mm. If you try cheaper options, you definitely want to order a p/u that has the plug already attached. I originally ordered a version w/o a plug and cut the plug off my original p/u. The wiring was different due to one having a mesh ground around the wiring. This should not be a concern if you do get the actual Fishman replacement part which does not appear to have the plug on the one I found on Amazon. The wiring should be the exact same. My $3 p/u easily trimmed trimmed with scissors length-wise but might sit too low for your needs (Bendable Piezo Cable Undersaddle Pickup For Acoustic Guitar - Worldwide by SODIAL on Amazon).
Question:	Is the cord really only 33mm in length? In the picture of the product, the cord appears to be 4 or 5 times as long as the pickup
Answer:	I've installed the pickup in a guitar, so I can't measure the wire, but my guess is that it's 33 cm. It's definitely not 33mm. It's long enough to reach from the saddle to an endpin or preamp on an acoustic guitar.