12 best toggle bolts

Product description

Swpeet Both Slot Headed and Phillips Headed Drive Bolts.



Sizes: 1/8", 3/16" and 1/4".



Toggle Wing Nut Dimensions：

1-9/16" x 1/16" x 3/8" (L x W x H) (10pcs),

2" x 9/16" x 1/2" (L x W x H) (8pcs),

2-1/8" x 11/16" x 9/16" (L x W x H) (6pcs).



Package included:

1/8" x 10pcs

3/16" x 8pcs

1/4" x 6pcs

User questions & answers

Question:	Hd suggested these for bar in shower to grab onto. Going through tile grout and wire mesh. Thinking 3 on each end so 6 total. Will that be strong
Answer:	Yes ... great!!
Question:	Will they work on the thin vinyl planels of mobile home walls
Answer:	I don’t know definitively but the bolts are very sturdy
Question:	How much weight can each one hold
Answer:	Each on is different. Back the screw our to it is just in the hinge. Then you can strighten toggle out alignen with the screw. This is the smallest it can get. Measure the toggle at the hinge. Remembet it is squar and it has to fit in a round hole so make it a little bigger.
Question:	How big do the holes have to be to insert the folded toggles
Answer:	There's a lever inside of the handle against the blade to hold it in place. If you can push it to the left with your thumb, you will be able to close it easily

Product description

• Toggle anchor installs behind 3/8"- to 3-5/8"-thick hollow materials including gypsum board, drywall, and concrete block to provide a secure hold from within the mounting material
• Anchor affixes to the wall before adding the bolt and fixture, allowing one-person installation and fixture changes
• Made in USA, and works with 1/4"-20 UNC-threaded metal bolts (sold separately)
• Ultimate tensile strength is 265 lb. in 1/2" drywall and 1,080 lb. in concrete block with a 1/4"-20 UNC bolt
• Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations)

User questions & answers

Question:	are these same quality as ones made by hilti
Answer:	You push the toggle in the hole, open it up, pull it back tight and then slide the plastic sleeve down until it is tight against the sheetrock on the outside and then carefully snap the excess strips that are sticking out on the outside and then you get your bolt and screw into it. We have put in hundreds of these that hold up hundreds of pounds and never had one break off. Hope this helps. Make sure you are drilling the size of hole they recommend to slip the toggle through. If the hole is too small, it binds the plastic in the sheetrock.
Question:	I received these and tried to use them but they break off behind the wall where the plastic attaches to the anchor. Anyone know why
Answer:	BA indicates 3/16", BB indicates 1/4"
Question:	whats the diff between ba and bb designition
Answer:	I have used it in plaster,you need to make a precision 1/2 hole and hope there is enough room for your bolt and the toggle to grab
Question:	Can this be used with Plaster walls
Answer:	Bolt heads are approximately 7/16 inch diameter. You certainly can add a flat washer if that is too small. The Threaded bolt is 1/4 inch diameter.

User questions & answers

Question:	Will this work going through wood and then through brick
Answer:	1/4" masonry bit. Note: I have used these in brick to hold a flag on my house. Granted, it was a pretty big flag but the whole thing was ripped from the wall twice during rather high winds. Just put the holder back up but swabbed the ribs with epoxy before tapping them into the brick. Hopefully this will do the trick. Despite that, you can't beat the price on these and are worth having.
Question:	What size is drill bit
Answer:	Depends on how you install them. I use them to install headboard units in hotels. I use 4 anchors in each of 2 brackets. The combined weight of the headboards is 135lbs.
Question:	How many pounds can this anchor hold
Answer:	General duty
Question:	is heavy dutty
Answer:	25.

• 【Professionals Toggle Anchor】Our anchor is in fact arguably the best anchor on the market today.With massive range of applications and fully tested, huge 'tensile pull out' and 'shear' strength.It is the ultimate answer to some of the most awkward and demanding tasks that professionals face when fixing to hollow materials such as cavity walls and ceilings.
• 【Save Money and Time ! 】Turn a 2-person job into a 1-person job.Other toggle bolt fixings are usually clumsy and difficult to install, ruin the rear side of the wall when over tightened and require a huge hole to be drilled to fit the anchor through. Our toggle anchor can be installed in less than 10 seconds thanks to its pivoting head and strap design.
• 【Premium Quality and Durable】Up to twice as strong as old fashioned wing toggles.This toggles anchors are engineered from impact and chemical resistant material,which are very durable.Its weight distribution over the entire solid metal channel head prevents any damage being done to the wall or ceilingIdeal for domestic and professional use with high quality.Made in U.S.A.
• 【Versatile Uses】Works in both cavity and solid material,simplicity and speed of application,Our anchor is a versatile plasterboard drywall anchor fixing with unrivalled strength and is suitable for all types of plasterboard,hardboard, plywood, sheet metal, chipboard, mdf, lath,and plaster and other materials.Ideal for mounting heavy items such as radiators/towel rails/kitchen cupboards/curtain rails/flat screen TV wall mounting brackets. curtain rails etc. the ultimate cavity fixing.
• 【Buy Risk Free】All Our anchor are backed by Lifetime warranty.Simply email us back if our product ever fails you and we'll mail you a new original replacement free of charge.

User questions & answers

Question:	Are these good for plaster walls
Answer:	Should be fine for plaster, it can also be use on concrete ,Tile, and more.
Question:	Does it difficult to mount
Answer:	YES,it's super easy to install if you follow the instruction.
Question:	Can it be used to mount towel bars in a bathroom
Answer:	Yes, They are strong enough for a towel bar.
Question:	What size of bit do I drill the hole with
Answer:	Hi, 1/2" is recommended.

Product features

IDEAL FOR HANGING!

INDOORS: FLAT PANEL TV's, Hand rails, Grab bars, ADA handware, Cabinets, Shlelving, Lighting Fixtures, Window treatments, Kitchen accessories, Bathroom accessories, Sinks, Partitions, Office furniture, Heavy machinery, Reinstallations, And much more.

OUTDOORS: Solar panels, Satellite antennas, Roofs, Decking, Garage doors, Marine applications, And much more.

TV Stand Installation

Hand the Shelf In Drywall

Various Types of Wall Holder

Safety Bathroom Grab Bars

Ultimate Load Data

• 1/2" Drywall: 265lbs
• 5/8" Drywall: 356lbs
• 1/2" Drywall+25 Gauge Stud: 425lbs
• 5/8" Drywall+25 Gauge Stud: 464lbs
• Concrete Block: 1080lbs
• 1/2" steel plate: 1288lbs
• Stainless in 1/2" steel: 1735lbs

Ultimate Shear Load

• 1/2" Drywall: 241lbs
• 5/8" Drywall: 324lbs

Pre-Install Without Bolt

Pre-installs without the bolt to make handling of fixture easier.

Reusable in the same hole—remove the bolt without losing the anchor.

Smaller installation hole

Maintains the integrity of wall, ceiling, or floor

Strengthening the anchoring. Ends the need to patch an oversized hole.

Strong & Heavy Duty

Up to 2x the load of an old-fashioned wing toggle

Can Use Screw Gun

Anchor does not spin, timesaver.

Product description

Specification:

Quantity: 24 PCS

Sizes: 1/8", 3/16", 1/4"

Material: Zinc Plated Steel

Product type: Toggle bolt and wing nut



Feature:

1, Made of zinc plated steel, uniform coating, strong adhesion and long service life, meanwhile, smooth surface because of using advanced automate production process to ensure processing accuracy, which make the product appearance is exquisite.

2, The spring can be folded into the drill hole without the need to unscrew the screw, and the installation is simple, the spring can be automatically opened behind the hollow substrate to form a large radius and large area contact, providing a reliable anchoring effect.

3, First, you need to drill a hole (big enough to thread through collapsed spring-loaded wings) and then poke these toggle bolts through the hole. At this time, the wings would release and clamp on the inside, then pull the bolt back down tight, please noted that you should leave enough room for wings to release. Finally, better use an electric screwdriver to screw the bolt in.



Package included:

1/8 inch toggle bolt-----------------12 Pieces

3/16 inch toggle bolt----------------8 Pieces

1/4 inch toggle bolt------------------4 Pieces



Package Quantity: HELIFOUNER 24PCS Toggle Bolt and Wing Nut



Warning: small parts, keep away from children and kids.

• 【Sizes】There are three sizes selected for you, includes: 12 pieces 1/8 inch, 8 pieces 3/16 inch, and 4 pieces 1/4 inch. 24 pieces in total. Different sizes and enough quantities can meet your different longtime using.
• 【Material】Our toggle bolts are made of zinc plated steel, uniform coating, strong adhesion and long service life, meanwhile, smooth surface because of using advanced automate production process to ensure processing accuracy, which make the product appearance is exquisite.
• 【Unique Design】The spring can be folded into the drill hole without the need to unscrew the screw, and the installation is simple, the spring can be automatically opened behind the hollow substrate to form a large radius and large area contact, providing a reliable anchoring effect.
• 【Easy To Install】First, you need to drill a hole (big enough to thread through collapsed spring-loaded wings) and then poke these toggle bolts through the hole. At this time, the wings would release and clamp on the inside, then pull the bolt back down tight, please noted that you should leave enough room for wings to release. Finally, better use an electric screwdriver to screw the bolt in.
• 【Wide Applications】It can be used for hollow brick, gypsum board, cement fiber board, wood board and other hollow substrates, Suitable for installing light fixtures such as lamps, curtain rods, photo frames, coat racks, power switches, what’s more, the product is highly adaptable, it can be installed quickly with a normal screwdriver.

User questions & answers

Question:	I need to hang a 25 pound clock. Would these largest of these work on drywall
Answer:	Yes, if you drill a hole all the way through, but if there are wooden slats behind the plaster there might not be room to get the toggle in!
Question:	Can these be used on a plaster wall
Answer:	I have used 2 ways that will work. You can either enlarge the hole around the anchor and using pliers pull on the screw until the anchor comes out of the wall or using a hammer, push the whole thing inside the wall then patch the hole. I hope this helps.
Question:	So how would you get anchors out of the wall or ceiling if you don't need this anymore
Answer:	China
Question:	Where are these made
Answer:	HILTI just buy from them and put them in a red HILTI box (and increase the price of course); you can read on top of the HILTI box "TOGGLER(r) = Worldwide Registered Trade Mark of Mechanical Plastics Corp"

• SIZE - 1/4 inch (4pcs), 3/16 inch (8pcs), 1/8 inch (12pcs), total 3 sizes of toggle bolt and wing nut.
• HIGH QUALITY - Made of high quality zinc plated carbon steel, rust resistance and corrosion resistance, durable enough for you to hanging items.
• UNIQUE DESIGN - The spring can be folded into the drill hole without the need to unscrew the screw, and the installation is simple.
• WIDE APPLICATION - Used for fixing lamps, bookshelves, hanging cabinets, sinks, curtain chutes, bookshelf chutes, cable trenches, hanging flower pots, water heaters, coat racks, etc.
• PACKAGE - All toggle bolt and wing nut are nicely enclosed in plastic case for easy access and carry with compartments for easy store.

User questions & answers

Question:	Can anyone who bought these tell me how wide the folded toggle bolts are for each size so I know what kind of drill bit to buy? asked on September
Answer:	That’s a good question. Because I needed to put one anchor through a metal cabinet already in place and needed to know that without drilling the cabinet out. The small is 10mm medium 15mm and large 18mm

Product features

ISPINNER 24pcs Zinc Plated Steel Round Head Toggle Bolt and Wing Nut Assortment Kit 1/4" 3/16" 1/8" for Hanging Heavy Items on Drywall

Made of high quality zinc plated carbon steel, rust resistance and corrosion resistance, durable enough for you to hanging items.

UNIQUE DESIGN

The spring can be folded into the drill hole without the need to unscrew the screw, and the installation is simple.

PACKAGE

All toggle bolt and wing nut are nicely enclosed in plastic case for easy access and carry with compartments for easy store.

• ★【STRONG AND WELL MADE】Quality zinc plated steel anchors, rustproof, anti-corrosion eco-friendly material. zinc steel can be used in humid environment and could last for a a long time. A brand new and excellent toggle bolt kit we offer. If not, please come to us soon, we promise to solve the problem for you. 100% satisfaction. We always believe that customer comes first.
• ★【HOUSEHOLD SPARE TOOLS】3 different sizes available(1/4”, 3/16”, 1/8”), each size kept in one separate compartment. This pretty much takes care of any light duty anchoring that would be needed in a regular household. Use in drywall, plaster wall and tile, thin or hollow walls and other board materials. Good quality little kit. Order now and store it for future use because it will make your home repair job much easier.
• ★【TIME SAVER HOME TOOLS】Got small items to hang on the wall and also some others large mirrors and pictures ? Buy this kit for spare tools would be great. Just move to a new place and have to rehang a lot of stuffs ? from shelves to picture frames, our anchors handle this all well for you. Once they are in, they have the powerful strength to hang your items. Make your new house nice and cozy. A better life for you.
• ★【HOW TO APPLY THIS KIT】First, you need to drill a hole (big enough to thread through collapsed spring-loaded wings) and then poke these toggle bolts through the hole. At this time, the wings would release and clamp on the inside, then pull the bolt back down tight, please noted that you should leave enough room for wings to release. Finally, better use an electric screwdriver to screw the bolt in.
• ★【QUALITY AFTER-SALE SERVICE】If you do not satisfy with our products or if you have any questions, please come to us, we would reply you within 12hours. We 100% guarantee to solve all the problems to your satisfaction. FREE REPLACEMENT within 90days.

User questions & answers

Question:	Hi, what three sizes of drill bit should I use for the three different size bolts
Answer:	1/8 hole size 3/8 3/16 hole size 1/2 1/4 hole size 5/8

Product description

The FlipToggle is the only single-strap design that takes the guesswork out of hollow-wall anchoring. Its unique design securely holds the toggle for easy insertion into the pre-drilled hole. Once inserted, the spring tab flips the toggle into the right position so that when the collar is tightened the anchor is ready for the bolt. No jammed toggles, broken straps or misaligned bolts. Key Features: Installs into drywall and hollow CMU up to 2 1/8" thick with a 2 1/2" bolt. Bolt size: 3/16"-24 thread. Simple one-strap design holds toggle perfectly aligned for easy bolt insertion The collar ensures centered bolt placement in the hole and does not embed the bolt into the drywall, eliminating the potential for sagging fixtures. Installation: FlipToggle installs in four easy steps: Fold, insert, flip and tighten -- it's that quick!

The Anchor requires a 1/2" hole and a 10-24 screw (included 2-1/2" long)

Specifications

 

SAFE WORKING LOADS 2:1**

Ultimate Tensile and Shear Strength Values

• 1/2" Drywall - Ultimate Tension 67 lb (38 kg), Ultimate Strength 106 lb (57 kg)
• 5/8" Drywall - Ultimate Tension 107 lb (52 kg), Ultimate Strength 188 lb (74 kg)
• Hollow Concrete Block - Ultimate Tension 415 lb (203 kg), Ultimate Strength 435 lb (204 kg)

** Loads may vary according to the quality of the drywall or concrete hollow block.

Warning: Use one-half or less of listed maximum values for safe working loads (as required by local regulations).

• What's in the Box?
• (10) Flip toggle anchors
• (10) 3/16"-24 UNC bolts

Environmental conditions: Indoor, dry conditions

Material composition: Polypropylene, Steel, zinc-plated, Plastic

• New one strap design for easier insertion and flipping operation
• Ideal for all type of hollow wall, up to 3" (75mm) thick
• Requires an one half inch hole
• Fast and easy installation
• Eliminates the potential for sagging fixtures

User questions & answers

Question:	Can a different sized screw work? Have shelves I want to hang that came with screws with a specific head to fit it
Answer:	Yes they will as long as you can get a half inch hole drilled through metal lathe without tearing up the plaster around it.
Question:	Will this work on lath and plaster walls
Answer:	Depends on how thin or thick the wall where the TV is to be mounted. I used 8 anchors for a 65 inch TV, which weighs between 55-65 pounds. For 90lbs, I believe 4 anchors is not enough. Hope that answer helped a little.
Question:	Can I support a 90lb tv with 4 anchors
Answer:	In 1/2" drywall, the 1/4" anchor is rated at 90 lbs.
Question:	how much weight will these anchors support
Answer:	This toggle is kinda overkill for a towel bar. However, if it

Product description

• Toggle anchor installs behind 3/8"- to 3-5/8"-thick hollow materials including gypsum board, drywall, and concrete block to provide a secure hold from within the mounting material
• Anchor affixes to the wall before adding the bolt and fixture, allowing one-person installation and fixture changes
• Made in USA, and works with 3/16"-24 UNC-threaded metal bolts (sold separately)
• Ultimate tensile strength is 238 lb. in 1/2" drywall and 802 lb. in concrete block with a 3/16"-24 UNC bolt
• Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations)

User questions & answers

Question:	The bolts are too large for my towel bar hardware. The hardware small little plates with oblong holes for the screws/bolts what to do
Answer:	These togglers are the very best for fastening something to the wall and require a 1/2" hole. 220 lb pull through 1/2" drywall. Get them in place with a stainless bolt and it isn't going anywhere.
Question:	What do you guys suggest for fixing a towel bar that is starting to pull away from the wall? Can I use this inside the existing holes? Total 40lbs
Answer:	Hello Julian,These are Togglers that will receive a 3/16" thickness bolt and the 24 is the thread count. So you can purchase bolts to go with these in any length 2", 2 1/2", 3" as long as they are 3/16 thickness with a 24 thread count. Hope that makes it clear.
Question:	What does 3/16"-24" actually mean? Does the 24" mean 2 feet? Is this a range or something? Confused
Answer:	According to their website, the bolts are NOT included.
Question:	do these include the bolts
Answer:	/Duration 0:05Loaded: 0.00%Stream Type LIVESeek to live, currently playing liveLIVERemaining Time -0:05 Playback Rate1xChaptersChaptersDescriptionsdescriptions off, selectedCaptionscaptions off, selectedAudio TrackFullscreenThis is a modal window. .noScriptDisplayLongText { display : none; } .noScriptNotDisplayExpander { display : none; } .noScriptDisplayLongText { display : block; } I hung this up with the small ones and this weight is 40 plus pounds. I also used them to put up shelves in laundry room to put towel and bleach and soap

Product features

TOGGLER SNAPTOGGLE BA Toggle Anchor

Our SNAPTOGGLE anchors get their name from their speed and ease of use—they work in a SNAP! Our high-strength, multi-functional TOGGLER High-Performance Anchors provide fast, easy, and secure fastening in almost all applications and substrates—from light- to heavy-duty.

We have sold billions of anchors worldwide without a single product liability claim.

Features:

- Straps that snap off flush with the wall every time, assuring precise alignment.

- A new plating that is 7x more corrosion-resistant than B633-85 Type III/Sc 1 government spec zinc plating .

Product description

• Toggle anchor installs behind 3/8"- to 3-5/8"-thick hollow materials including gypsum board, drywall, and concrete block to provide a secure hold from within the mounting material
• Anchor affixes to the wall before adding the bolt and fixture, allowing one-person installation and fixture changes
• Made in USA, and includes 3/16"-24 UNC-threaded bolts
• Ultimate tensile strength is 238 lb. in 1/2" drywall and 802 lb. in concrete block with a 3/16"-24 UNC bolt
• Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations)

User questions & answers

Question:	Will nylon strap togglers work on a fiberglass shower to hang a fold up seat
Answer:	Please Note: These are made in a variety of sizes, depending on your needs. Determine your screw size, and order the corresponding size in the Toggler. By the way, The Toggler Snaptoggle is a terrific asset in mounting things which are fairly heavy. Mounted a 4 ft. long tool holder.......with these things. As you can imagine, the total tools stored in the rack are pretty heavy......and it did and continues to do a great job of keeping them securely in place.
Question:	screw size
Answer:	Yes, as a general rule, you can always cut machine screws shorter as long as you are careful to clean up the cut end after you cut them. One trick is to thread a nut on the screw before you cut it, then unscrew it after you make the cut, the nut will straighten out any rolled over threads on the way off the end. Or, you could cut carefully with an abrasive wheel or dress the end of the screw with a grinding stone. Even better, chase the threads with a thread cutting die. Or, just go to the hardware store and buy a shorter screw. This toggle uses 3/16-24 (often called #10-24) screws. Available in a variety of lengths pretty inexpensively.
Question:	Will it still work if I snip the end of the bolt? There is a brick wall behind the draywall I am anchoring to, and the bolt is too long
Answer:	It's zinc played steel. Not 24 karat gold.
Question:	Do they come in any other metal than solid 28 karat gold
Answer:	Lauren, these toggle anchors are fantastic for hanging heavy objects on walls. You definitely want the TC (3/4") or TD (1") size for plastered walls. Plastered walls are at least 3/4" thick or greater. Suggest you drill a 1/8" pilot hole to try to determine your wall thickness before you buy.

Product description

Toggle bolts come with spring-action wings and are intended for anchoring into hollow walls. The wing is designed to spread apart behind the base material upon installation for firm hold in hollow wall applications. The wing disperses the weight of the secured item over a larger area, increasing the weight that can be secured compared to a regular bolt.

From the Manufacturer

Toggle bolts come with spring-action wings and are intended for anchoring into hollow walls. The wing is designed to spread apart behind the base material upon installation for firm hold in hollow wall applications. The wing disperses the weight of the secured item over a larger area, increasing the weight that can be secured compared to a regular bolt.

• Durable toggle bolt great for hanging objects on hollow wall
• Comes with spring-action wings
• Features a slotted round head machine screw
• Pre-drilled hole required for installation
• 50 pieces per retail package

User questions & answers

Question:	can the screww be removed prior to installation in order to add a washer
Answer:	Yes. You would remove the screw from the toggle and insert it into the object you're trying to hang anyways.
Question:	How much weight do these support
Answer:	Don't know that anyone can answer this question accurately then the company. These are solid supports, so I would think that the dry wall would give way before the support does, if it was used to support an extremely heavy object.
Question:	Hi, how do I take these bolts out of the wall
Answer:	Once its installed, you cannot get it out. You can take the screw out, but not the toggle, unless you break the wall.
Question:	what size hole do you drill
Answer:	For 3/16” size you need to drill a 5/8” hole. 1/2” is too small and the wings will not pass through it.

Product description

Specification:

Quantity: 45 PCS

Sizes: 1/8", 3/16", 1/4"

Material: Zinc Plated Steel

Product type: Toggle bolt and wing nut



Feature:

1, Made of zinc plated steel, uniform coating, strong adhesion and long service life, meanwhile, smooth surface because of using advanced automate production process to ensure processing accuracy, which make the product appearance is exquisite.

2, The spring can be folded into the drill hole without the need to unscrew the screw, and the installation is simple, the spring can be automatically opened behind the hollow substrate to form a large radius and large area contact, providing a reliable anchoring effect.

3, First, you need to drill a hole (big enough to thread through collapsed spring-loaded wings) and then poke these toggle bolts through the hole. At this time, the wings would release and clamp on the inside, then pull the bolt back down tight, please noted that you should leave enough room for wings to release. Finally, better use an electric screwdriver to screw the bolt in.



Package included:

1/8 inch toggle bolt-----------------20 Pieces

3/16 inch toggle bolt---------------15 Pieces

1/4 inch toggle bolt-----------------10 Pieces



Package Quantity: HELIFOUNER 45PCS Toggle Bolt and Wing Nut



Warning: small parts, keep away from children and kids.

• 【Sizes】There are three sizes selected for you, includes: 20 pieces 1/8 inch, 15 pieces 3/16 inch, and 10 pieces 1/4 inch. 45 pieces in total. Different sizes and enough quantities can meet your different longtime using.
• 【Material】Our toggle bolts are made of zinc plated steel, uniform coating, strong adhesion and long service life, meanwhile, smooth surface because of using advanced automate production process to ensure processing accuracy, which make the product appearance is exquisite.
• 【Unique Design】The spring can be folded into the drill hole without the need to unscrew the screw, and the installation is simple, the spring can be automatically opened behind the hollow substrate to form a large radius and large area contact, providing a reliable anchoring effect.
• 【Easy To Install】First, you need to drill a hole (big enough to thread through collapsed spring-loaded wings) and then poke these toggle bolts through the hole. At this time, the wings would release and clamp on the inside, then pull the bolt back down tight, please noted that you should leave enough room for wings to release. Finally, better use an electric screwdriver to screw the bolt in.
• 【Widely Applications】It can be used for hollow brick, gypsum board, cement fiber board, wood board and other hollow substrates, Suitable for installing light fixtures such as lamps, curtain rods, photo frames, coat racks, power switches, what’s more, the product is highly adaptable, it can be installed quickly with a normal screwdriver.

User questions & answers

Question:	How long are the bolts
Answer:	1/8” diameter is 2 1/8” long 3/16 diameter is 3 1/16” long 1/4” diameter is 3 1/4” long