11 best monoprice monopods

Product description

Carbon Fiber Tripod/Monopod Expert Series - Large (12154) Effortlessly keep your camera steady and stable with this Carbon Fiber Tripod. This tripod is constructed of carbon fiber; which provides the most strength and least weight possible. The quick release leg extension locks and locking leg angles make it easy to quickly setup; so you won't miss that perfect shot while messing around with complicated or difficult to use accessories. The tripod can be setup with a maximum height of 65.4" to a minimum height of only 11.2". The central column can be detached from the tripod and used as a monopod; with a maximum length of 68.9". It weighs only 70.5 oz.; can accommodate up to 44 lbs. weight capacity; and when folded for storage; measures only 17.7" long. It features a 3/8"x16 screw mount for attaching a camera head (not included). A zippered nylon carrying/storage bag with shoulder strap is also included. Features: Maximum Height: 65.4" (1660mm) Minimum Height: 11.2" (285mm) Maximum Monopod Length: 68.9" (1750mm) Folded Length: 17.7" (450mm) Weight: 70.5 oz. (2000g) Load Capacity: 44.0 lbs (20kg) Tube Diameter: up to 29mm

Product description

Get superior guitar tone and flexibility using this 15-Watt, 1x12 Guitar Combo Tube Amplifier with Celestion Speaker & Spring Reverb from Monoprice! As the title indicates, this guitar amplifier features a 15-watt tube power amplifier and a Celestion brand speaker. It uses three ECC83/12AX7 preamplification tubes and two EL84 power tubes for the amplifier section, plus a Celestion Red Truvox 1215 speaker. The EL84 tube is the tube that powered the Mullard amplifiers favored by the British Invasion bands of the 1960s. It can produce a full output from a relatively small signal and is therefore easily overdriven to produce that distinctive chiming, treble-heavy sound, especially when compared to the 6L6 tubes more commonly used in 1960s era American guitar amps. The amplifier handles frequencies between 80Hz and 10kHz, with hum and noise -75dB below the rated power and 0.5% total harmonic distortion. It includes a Low input and a High input, with the former attenuating the signal by approximately 50% and the latter being easier to overdrive. The cabinet is ported in the rear and features a leather handle, cloth speaker grill, and a cream-colored, textured, synthetic leather exterior with chrome corner guards. The amp features a genuine spring reverb with the ability to enable it remotely using a foot switch. It supports FX send and receive, so you can either connect it to an effects processor or use the send/receive connections as line out and line in connections. Two inputs allow you to select between the full power mode and a 1 watt limited amplification mode for recording or late night practice sessions.

• Superior guitar tone and flexibility using this 15-Watt, 1x12 Guitar Combo Tube Amplifier with Celestion Speaker & Spring Reverb from Monoprice!
• Features a 15-watt tube power amplifier and a Celestion brand speaker. Amplifier Load Range: 8 ~ 16 ohms
• Uses three ECC83/12AX7 preamplification tubes and two EL84 power tubes for the amplifier section, plus a Celestion Red Truvox 1215 speaker.
• Handles frequencies between 80Hz and 10kHz, with hum and noise -75dB below the rated power and 0.5% total harmonic distortion.
• The cabinet is ported in the rear and features a leather handle, cloth speaker grill, and a cream-colored, textured, synthetic leather exterior with chrome corner guards

User questions & answers

Question:	What does a foot switch do on the amp? Does a foot switch come with the amp? If not, where can one be bought
Answer:	A footswitch is not included. When used with this amp, a footswitch will turn the amp's built-in spring reverb on and off. You can buy a simple on/off footswitch for under $20. Checkout the Fender footswitch sold on Amazon.
Question:	Wasn't this being sold for
Answer:	Monoprice raised the shipping to $50 when it was on sale for $200. There was no sale...
Question:	Will this amp make me sound good enough that I can quit my guitar lessons
Answer:	Definitely!! Get 2 of them and you can GIVE guitar lessons!
Question:	can I put 12 oz bottle of beer on this amp and a pack of marlboro reds at the same time
Answer:	You can fit a six pack and a few packs of smokes on it.

Product features

15-Watt, 1x12 Guitar Combo Tube Amplifier

Get superior tone and flexibility using this 15-Watt, 1x12 Guitar Combo Tube Amplifier with Celestion Speaker and Spring Reverb. Three industry standard 12AX7 tubes drive the preamp and reverb sections, while a pair of EL84 tubes deliver the punch. The spring reverb can be switched on or off using a foot pedal and the 3-band equalizer allows you to really dial in your sound. The cabinet has an open back and features a leather handle, cloth speaker grill, and a cream-colored, textured, synthetic leather exterior with chrome corner guards.

Tube Amplifier

Three industry standard 12AX7 tubes drive the preamp and reverb sections, while a pair of EL84 tubes deliver the punch.

Spring Reverb

The genuine spring reverb adds a lush spaciousness to your tone and can be switch on or off using a foot pedal.

FX Loop

The FX loop allows you to insert effects between the preamp and power amp sections, giving more versatility to your sound.

Classic Styling

Enjoy the tone and styling of the 40's and 50's with the classic cream-colored, textured, synthetic leather exterior with chrome corner guards.

You Spoke, We Listened

At Monoprice, we take cutomer opinions very seriously. We have taken our customer reviews to heart and improved the spring reverb and made some cosmetic changes to simplify operation over the previous version of this amp.

Tubes are King

In a world dominated by innovation and digital emulation the vacuum tube or valve is still the undisputed king of the guitar amplification world.

Versatile and Durable

The amp features a low and a high input, an improved reverb tank, an FX loop, and a 3-band equilizer. The Celestion Seventy 80 is detailed and crisply defined, with a tightly controlled low-end and punchy, aggressive upper mid-range. The top-end response is also subtly increased.

Buy with Confidence

Monoprice not only stands behind every product we sell with a 1 year replacement warranty, we offer a 30-day money back guarantee as well! If the product you purchase does not satisfy your needs, send it back for a full refund.

Quality at a Fair Price

Monoprice's rugged design and rigid quality control standards deliver high quality products at fair prices.

Hassle Free Packaging

Monoprice exists to bring simplicity, fairness, and confidence to technology choices. This product features recyclable packaging that is simple to open, cost effective, with minimal waste, and fully protective as it travels to you.

Service & Support

You're never on your own with Monoprice products! We have a full team of friendly and knowledgeable technicians available to answer your questions, both before and after the sale. Contact our technical support team for questions about our products, troubleshooting, or even suggestions for products to fit your particular needs. Not to be outdone, our friendly and helpful customer service team is here to make your ordering, delivery, and any possible returns a quick and painless operation, from start to finish!

Product description

Overview The Sirui P-326 Carbon Fiber Monopod is an extremely lightweight camera support that's ideal for mobile operation with a DSLR, point & shoot camera, or a compact camcorder. For some situations, such as tourist locations where tripod use is prohibited, a monopod is the perfect way to fly under the radar but still ensure steady shots. Package Contents Sirui P-326 Carbon Fiber Monopod Wrist Strap. Purchases from unauthorized dealers may include NON-US market products which will not receive LIMITED US-ONLY MANUFACTURE WARRANTY. See Siruiusa.com for a list of authorized dealers.

• Light-weight 8X carbon fiber in 6 sections
• Reversible 1/4"-20 & 3/8"-16 screw on the mounting plate
• Wrist strap and hand grip for comfortable hold and insulation
• Silicon twist lock enhances durability

User questions & answers

Question:	What is the max weight capacity for this monopod
Answer:	It is made of plastic.
Question:	Does the foot of the monopod unscrew? If so, what are the threads
Answer:	Probably
Question:	Will I need other parts
Answer:	Yes, it all came in one package.
Question:	There's no mention of the monopod's length when fully extended. Has anyone checked
Answer:	Yes, it has the standard 3/8" female thread along with a couple of insert 3/8" threaded bolts for either male or female threaded standard heads. For example I can fit my Manfrotto 804RC2 head--however at 700g versus 300g for the one this comes with, it adds to the top-heaviness. Also the original neatly fits into the slingbag which not only weighs a lot less than full-size tripod, but is much less of a bore to cart around. This portability is the main reason to buy this one, especially for travel.

Product description

Weatherproof Hard Case with Wheels and Customizable Foam, 33 x 22 x 17 in



Provide IP67 level dust and water protection for AV equipment or tools using this customizable footlocker style Weatherproof Hard Case from Monoprice!



The IP, or Ingress Protection, rating is a two digit value that indicates the level of protection provided by the cases. The IP67 rating of this case means that it provides complete protection against dust and other solid particles and that it can withstand up to 30 minutes of submersion in water at up to 1 meter depth.

The case is constructed of impact and ultraviolet resistant polypropylene and has a fully customizable foam interior for superior shock protection. A pressure relief valve allows you to slowly and safely equalize the pressure inside and out.

This case features a pair of 2.3" heavy-duty wheels and a folding handle, which allows you to roll the load. The handle extends about 8", resulting in the top of the handle being about 41" off the floor when the case is standing on its side. Additionally, it has full load handles on each side so two people can carry the load.



Features:

• Designed and developed to the comply with the highest safety protection standards

• Waterproof up to 1 meter depth for 30 minutes

• Shockproof design with fully customizable foam interior

• Total protection against dust and other solid material

• Ultraviolet and impact resistant material

• Manual pressure relief valve allows for gradual pressure equalization

• Seal design provides IP67 level protection

• 2.3" heavy-duty wheels and foldable handle for easy portability

• Full load handles on each side so two people can carry the load

• Customizable name plate

• 6mm diameter lock holes

• -40 ~ +194°F (-40 ~ +90°C) operating temperature

• 8900 cu in (145.84 liter) internal volume

• 315.26 lbs (143.0 kg) maximum buoyancy

• 33.50" x 21.89" x 16.89" (851 x 556 x 429 mm) external dimensions

• 30.04" x 19.02" x 15.83" (763 x 483 x 402 mm) internal dimensions

• Weighs only 36.75 lbs (16.67 kg)

• Waterproof up to 1 meter depth for 30 minutes, Seal design provides IP67 level protection.
• Designed and developed to the comply with the highest safety protection standards with shockproof design offering fully customizable foam interior.
• Ultraviolet and impact resistant material with pressure relief valve allows for gradual pressure equalization.
• 8900 cu in (145.84 liter) internal volume and weighs only 36.75 lbs (16.67 kg).
• Internal: 30.04 x 19.02 x 15.83 (763 x 483 x 402mm). External: 33.50 x 21.89 x 16.89 (851 x 556 x 429mm).

User questions & answers

Question:	Creative xp hd spotting scope with tripod 20-60x80mm will this fit into this case
Answer:	Your question mean nothing to anyone. What are the dimensions of your spotting scope, then we can help.
Question:	Can I check this size at airlines? 33.50 x 21.89 x
Answer:	For domestic travel the limit is 62 linear inches, ie., length+width+height
Question:	Are these cases airtight
Answer:	The title states IP67. If you need an "airtight" case, you should also look into what the IP ratings mean. Ingress Protection (#solid) (#liquid) The "6" rating means: Dust tight. No ingress of dust. The "7" rating means: Protection against the effects of immersion in water between 1cm and 1 m for 30 minutes
Question:	how many layers of foam are there
Answer:	4

Product features

About Us

We exist to bring simplicity, fairness, & confidence to technology choices.

Established in 2002, we have built a stellar reputation for product excellence. We offer over 7,000 high-quality, electronics and accessories to professionals and consumers worldwide. Our proven business model eliminates entire layers of markup within the supply chain, which allows us to sell premium products.

Product description

Monoprice Mini Delta 3D Printer Fully Assembled with Heated Build Plate and Auto Calibration for ABS PLA with Micro SD From the #1 Best-Selling 3D Printer Brand in the World (Source: CONTEXT Q3’17 AM3DP Report) Empower your children's creativity, or your own, with the lowest-priced professional quality 3D Printer in the world. With a steel frame wrapped in black anodized aluminum shell and 50 micron layer resolution, you can see and feel right away that this is no toy. The delta design style continuously self-calibrates, so you will never have to struggle with bed leveling. The print bed and extrusion nozzle heat to a wide range of temperatures, allowing you to print with different materials. Auto Calibration: The delta design style continuously self-calibrates, so you will never have to struggle with bed leveling. Fully Assembled: The MP Mini Delta 3d Printer comes fully assembled, ready to print out of the box. Durable: The steel frame and black anodized aluminum frame makes this printer extremely durable and capable of withstanding some serious abuse. Open Source: The print bed and extrusion nozzle heat to a wide range of temperatures, allowing you to print with different filament types from any manufacturer. Additionally, it has the ability to use open source software, such as Cura or Repetier, allowing you to tailor your 3D printing experience to your personal tastes. Features: • 50 micron layer resolution • Can print from a computer using a wireless Wi-Fi or physical USB connection, or offline with a microSD card • Up to 150mm/sec print speed• 180 ~ 260°C extruder nozzle temperature range • Up to 60°C build plate temperature range • ø110 x 120 mm build area • Compatible with Windows and Mac OS X What's in the box • 1x 3D printer • 1x Filament holder • 1x Plastic scraper • 1x USB. Operating System Support - Windows(XP and later 32/64-bit) Mac OS X(10.6+ 64-bit). Avoid locations near air conditioning vents and windows. It may also be helpful to cover the printer or enclose the printer to print ABS more successfully

• Auto calibration: the delta design style continuously self-calibrates, so you will never have to struggle with bed leveling
• Fully assembled: the MP Mini Delta 3D printer comes fully assembled, ready to print out of the box
• Durable: the steel frame and black anodized aluminum frame makes this printer extremely durable and capable of withstanding some serious abuse
• Open source: the print bed and extrusion Nozzle heat to a wide range of temperatures
• Professional quality prints: up to 50 micron layer resolution. Can print from a computer using a wireless wi-fi or physical usb connection, or offline with a microsd card

User questions & answers

Question:	can you use a usb
Answer:	You can print by saving your glide print file on a usb thumb drive, and plugging it into the printer, if that is your question.
Question:	How do you turn it off
Answer:	I've attached it to a remote switch, so when my software sends a notification to my phone, I can turn the printer off remotely via IFTTT and the Belkin WeMo switch.
Question:	So, Im looking for a beginner printer to design models. Would anyone recommend
Answer:	This is an, "it depends," item. It's not a bad place to start as Chris P. indicates, but there's gotchas. And there'll be gotchas with his suggestion. Let me disclose the main gotchas so most can go make an eyes-open decision there. It has a self-leveling function, that had they chose better bed retention clips than the cheap push-pin rivet hold-downs that they went with, that would make it perfect for a beginner. There's 3D models online that let a novice actually quickly print proper magnetic retentions that will let you level it pretty consistently and robustly, so that's only a gotcha if you're not told ahead of time (You're now informed- look for them on Thingiverse under "monoprice mini delta" and you're looking for the "adjustable magnetic bed clips") It's hot-end will robustly do any of the common filiments (Nylon, Polycarbonate, etc. are high performance and not "common") such as PLA, PETG, and ABS, but the printer itself as it is stock is limited to PLA due to firmware limitations that prevent the bed getting any hotter than 60 deg C- and with the stock supply you won't get any better than 50 deg C which is only sort of good for PLA. Another community described modification is to use a 10 A power supply instead of the supplied 5 A one and then use the Open Source Marlin firmware as a custom backport for this printer. It should be noted that this operation will void your warranty. That being said, it will unlock the printer to it's fullest abilities, including cleanly working with a PC via the USB port, the ability to quickly heat the print head to 235 deg C and less, and to set bed temps up to 80 deg C, allowing you robust PLA printing and even PETG printing. So, if you're not expecting to tinker a bit with the printer, no, this isn't a printer for a beginner as it requires help to make it reach MOST of it's claimed potentials. If you don't mind a bit of additional work and don't care so much about warranties, it's a workhorse and a diamond in the rough.
Question:	Does this printer have an enclosed cover like bibo 3d printer
Answer:	No. The printer does not have an enclosed cover. It is fully open.

Product features

Monoprice Mini Delta 3D Printer

Empower your children's creativity, or your own, with a steel frame wrapped in black anodized aluminum shell and 50 micron layer resolution, you can see and feel right away that this is no toy. The delta design style continuously self-calibrates, so you will never have to struggle with bed leveling. The print bed and extrusion nozzle heat to a wide range of temperatures, allowing you to print with different materials.

Auto Calibration

Auto Calibration: The delta design style continuously self-calibrates, so you will never have to struggle with bed leveling.

Fully Assembled

Fully Assembled: The MP Mini Delta 3d Printer comes fully assembled, ready to print out of the box.

Durable

Durable: The steel frame and black anodized aluminum frame makes this printer extremely durable and capable of withstanding some serious abuse.

Open Source

Open Source: The print bed and extrusion nozzle heat to a wide range of temperatures, allowing you to print with different filament types from any manufacturer.

Product description

Get superior guitar tone in a small package using this 5-Watt 1x8 Guitar Combo Tube Amplifier with Celestion Speaker from Monoprice! As the title indicates, this guitar amplifier features a 5-watt tube power amplifier and a Celestion brand speaker. It uses a ECC83/12AX7 preamplification tube and a 6V6GT power tube for the amplifier section, plus a Celestion Super 8 GBA-15 speaker. The amplifier handles frequencies between 80Hz and 10kHz, with hum and noise -75dB below the rated power and 0.5% total harmonic distortion. It includes a Low input and a High input, with the former attenuating the signal by approximately 50% and the latter being easier to overdrive. The cabinet is ported in the rear and features a leather handle, cloth speaker grill, and a cream-colored, textured, synthetic leather exterior with chrome corner guards.

• As the title indicates, this guitar amplifier features a 5-watt tube power amplifier and a Celestion brand speaker.
• It uses a ECC83/12AX7 preamplification tube and a 6V6GT power tube for the amplifier section, plus a Celestion Super 8 GBA-15 speaker.
• The amplifier handles frequencies between 80Hz and 10kHz, with hum and noise -75dB below the rated power and 0.5% total harmonic distortion.
• It includes a Low input and a High input, with the former attenuating the signal by approximately 50% and the latter being easier to overdrive.
• While tone is always debatable, the increased dynamic range and even-order harmonic distortion of tubes produces the better sound.

User questions & answers

Question:	What happened to the old design that was like a Princeton in a tweed champ size? This has knobs in front now what else was changed
Answer:	Yes, the selling price indicated is for one unit. Regards
Question:	Would I be able to select 1 watt output, connect speaker out to another amplifier, and essentially use this as a preamp to say a Fender Champion
Answer:	Yes! It does come with a footswitch.
Question:	I've got a fender mustang amp. should i switch to this one? everyone says tube amp is way to go but honestly i can't hear it in demo videos
Answer:	Hi! It is on the back of the amp.
Question:	Has anyone changed the tubes on 5-watt monoprice amp; If so, what kind and what level of difficulty
Answer:	Yes. This is a tube amp. It has 2x ECC83 preamp tubes and 1x EL84 power tube

Product features

Tube Amplifier

Tube Amplifier: An industry standard 12AX7 preamp tube drives a single 6V6GT tube for a well-rounded tone and smooth, rich distortion.

Simple Controls

Simple Controls: Simple and minimalist controls keep the circuit clean and the tone pure, making it perfect for pedals.

Celestion Super 8

Celestion Super 8 Speaker: Well-balanced mids and highs complement a surprisingly meaty bottom end - it's just about the biggest sounding eight-inch speaker we've ever heard.

Classic Styling

Classic Styling: Enjoy the tone and styling of the 40's and 50's with the classic cream-colored, textured, synthetic leather exterior with chrome corner guards.

Tubes are King

While tone is always debatable, the increased dynamic range and even-order harmonic distortion of tubes produces the better sound.

Versatile and Durable

The amp features separate volume and tone controls, a 1-watt/5-watt button, and an 8-inch Celestion speaker, all contained within a solid frame with classic, cream styling.

Product description

This Kevlar in-wall speaker offers the perfect combination of performance and style. The use of aramid fiber for the woofer means that the speaker can hit harder, go lower, and handle more power with significantly less distortion than conventional drivers. The titanium silk dome tweeter produces clean, crisp, and clear highs and mids.







You can fine tune the blend of sound using the built-in high frequency attenuator in case your room is too bright. The metal grille can be painted to match your ceiling. Easy to install with simple hand tools, less time working and more time relaxing.







All Caliber series in-wall and ceiling speakers are sonically matched to provide a uniform sound stage across you entire listening area. Simple two channel listening rooms to full screening rooms with 7.2.4 Atmos and DTS-X immersive cinema systems will benefit from the matched components of the Caliber series installation speakers.







Model: 6816

Frequency Response: 50 Hz ~ 20 kHz

Impedance: 8 ohms

Power Handling Capacity: 100 watts Nominal, 200 watts maximum

Woofer: 9"" Kevlar woven cone with 30 oz. magnet and rubber surround

Midbass: 3"" Kevlar woven cone with 5.4 oz. magnet and rubber surround

Tweeter: 1"" Silk Membrane dome

Sensitivity: 90dB ±2dB (1.0m/2.83V)

Crossover: 12dB per Octave (with -3dB, -6dB Switch)

Cut-Out Dimensions: 12.8"" x 8.7"" 3.6"" (324 x 222 x 91 mm)

Overall Dimensions: 14.1"" x 10.0"" x 3.9"" (357 x 255 x 100 mm)

• DuPont Kevlar fiber cone drivers delivery clean bass reproduction, This lightweight transducer is a natural sound with significantly less distortion than conventional drivers.
• Immerse yourself in airy detailed clarity with defined vocals and dialog from the pivoting titanium Silk dome tweeters of these installed speakers.
• Enjoy caliber speakers as main home theater speakers and whole home house systems or add as Surrounds and immersive sound sources.
• No logo grills add to the minimal look and increases the “wife acceptance factor”.
• Buy confidently with a 30-day money-back guarantee and our 1-year warranty.

User questions & answers

Question:	Are they Bluetooth
Answer:	No they are not Bluetooth.
Question:	does the 10" Subwoofer vibrate the walls and create any weird unwanted sounds
Answer:	I installed mine into new and properly fastened drywall and have no issues with rattling
Question:	my garage is unfinished (studs only) how much of an area do i need to enclose with drywall on the ceiling to make these sound good
Answer:	Most are designed for infinite baffle application. Meaning they do not need a box to sound good. However building boxes for them normally does help the sound
Question:	Will these speakers fit into a stud depth
Answer:	Yes they fit std 3. 1/2" stud depth

Product features

Caliber 8in Fiber In-Wall Speakers 3-Way (pair)

In-wall speakers allow you to expand your listening environment throughout your entire home, as well as removing the clutter of giant box speakers, giving you back your living space. In either case, it's a win-win situation for those who desire high fidelity and those who put emphasis on decor. Featuring a removable and paintable grille, the Caliber series of in-wall speakers are sonically matched to provide a uniform sound stage across your entire listening area. From simple two channel listening rooms to full home theater screening rooms with 7.2.4 Atmos or DTS:X immersive audio technology, your system will benefit from the matched components of the Caliber series speakers.

What's in the box

2x 8" 3-way in-wall speaker with grill, Installation instructions, Cutout template and paint mask, Grill removal tool, Grill putty.

Dupont Kevlar Fiber Cone Driver

Kevlar is very light, rigid, and strong and delivers clean bass reproduction. This lightweight transducer produces a natural sound with significantly less distortion than conventional drivers.

Titanium Silk Dome Tweeters

Titanium silk offers good projection with warm tones. Immerse yourself in airy, detailed clarity with defined vocals and dialog from the pivoting titanium silk dome tweeters of these speakers.

Versatile

Enjoy Caliber series speakers as main home theater speakers, for whole home sound systems, or add them as surrounds in immersive sound systems.

Product description

Get everything you need for a great sounding home theater speaker setup in a single box! You get four satellite speakers and a center channel speaker for the mid- and high-range audio signals, plus an 8-Inch powered subwoofer to handle the low frequencies. All the speakers come with an attractive black finish and convenient spring-loaded signal connectors. The center speakers use two 3-Inch shielded mid-range cones, while the satellites employ one 3-Inch cone and a 1/2-Inch dome tweeter. However, don't let the small size fool you! These 8 ohm speakers will handle up to 125 watts of power from your home theater receiver at frequencies from 150 Hz to 20 kHz. The subwoofer is powered by a 60 watt (RMS) amplifier, driving a downward firing 8-Inch cone. It can take either line or speaker-level inputs, so can be used with any amplifier, even older amps without dedicated subwoofer outputs. The subwoofer handles frequencies between 50 Hz to 250 Hz and includes adjustable crossover frequency and volume balance controls. Also included in the box are four C brackets for mounting the satellite speakers to the wall and the necessary hardware for mounting the speakers to the brackets. A pair of plastic feet to properly orient the face of the center speaker is also included. Note that you will need to provide your own hardware for mounting the C brackets to the wall or other vertical surface. Don't let the low price fool you! This speaker system sounds great and will fill your room with high-quality, full-spectrum sound! Note: The speaker wire connectors on each unit comfortably accept a maximum 16 gauge speaker wire. For best results use pin-type speaker plugs to make the speaker connections and banana or pin-type plugs to connect the wires to your amplifier.

• Surround yourself in high-fidelity with the Monoprice 5.1-channel Home Theater Speaker System!
• This speaker system features four satellite speakers and a center channel speaker for the mid- and high-range audio signals, plus an 8" powered subwoofer to handle the low frequencies. All the speakers come with an attractive black finish and convenient spring-loaded signal connectors.
• The center speakers use two 3" shielded mid-range cones, while the satellites employ one 3" cone and a 1/2" dome tweeter. However, don't let the small size fool you! These 8 ohm speakers will handle up to 125 watts of power from your home theater receiver at frequencies from 150 Hz to 20 kHz.
• The subwoofer is powered by a 60 watt (RMS) amplifier, driving a downward firing 8" cone. It can take either line or speaker-level inputs, so can be used with any amplifier, even older amps without dedicated subwoofer outputs. The subwoofer handles frequencies between 50 Hz to 250 Hz and includes adjustable crossover frequency and volume balance controls.
• Also included in the box are four C brackets for mounting the satellite speakers to the wall and the necessary hardware for mounting the speakers to the brackets. A pair of plastic feet to properly orient the face of the center speaker is also included. Note that you will need to provide your own hardware for mounting the C brackets to the wall or other vertical surface.

User questions & answers

Question:	What speaker stands work with the Monoprice
Answer:	Any stand will work. I purchased wall mounts for my surround speakers.
Question:	Could I use this with a receiver and what would I need to do to get it to work correctly
Answer:	It will work with any 80-100w/ channel receiver. Connect using banana plugs and 14 gauge speaker wire. Make sure to get the woofer spreaker cable with a Y splitter. Monoprice website sells all the cables you need at a great price. Better than amazon
Question:	Could anyone recommend a set of towers to make this a 7.1 system
Answer:	I would definitely agree. Monoprice sells a set of two of the speakers separately for use on their own as a 2 channel system or as an add on to this 5.1 system to make it 7.1. They even sell the subwoofer separately as well if you ever want to upgrade to a true 7.2 system. Then everything will be perfectly matched. Make sure to get the correct set of two Premium Monoprice speakers. Monoprice also sells a lower quality standard 5.1 surround sound system and a set of two extras of that type as well. If you have the correct set, they will exactly match the speakers in the Monoprice Premium 5.1 surround sound speaker set. I know this because I actually had what I thought was the correct one in my shopping cart only to find out it was the wrong set just before pulling the trigger. So it's an easy mistake to make even when you've done a bunch of research. I hope you enjoy your system. They are absolutely amazing speakers. My family is constantly amazed at how much information and nuance is embedded in soundtracks of our favorite movies and shows that we never heard with our previous home theater system. It's like a completely different experience now. Good luck.
Question:	What are the dimensions of the individual speakers? I'm espescially curious on the size of the center channel
Answer:	The center channel is 4x9.5x4 Height, width, Depth respectively. The Subwoofer:12x10x12, The Satellites are :6x4x4

Product features

Monoprice 5.1 Channel Home Theater Satellite Speakers And Subwoofer - Black

This headphone amplifier features a USB input and a professional level Texas Instruments Digital to Analog Converter (DAC), effectively replacing your sound card without requiring you to open your PC and installing a new card. The high-current output allows it to drive headphones with a wide range of impedances, from 16 ohms to 600 ohms.

The RCA line outputs allow you to send the output to a stereo amplifier or powered speakers for those times when you don't want to use headphones. A set of RCA line inputs allows you to connect an external audio source, such as a CD player, so you can enjoy the advantages of the high-current headphone output with other audio sources.

Product description

Get Professional quality sound from everyday headphones. These 'phones look great anywhere you go and sound great for hours at a time. It features ultra-comfortable ear pads with a good amount of isolation to keep you focused on the task at hand. Enjoy clean robust sound across the audio spectrum. They are perfect for mobile devices, Hi-Fi, and audio/video production. Ultra-comfortable: the soft, split-leather ear pads help prevent fatigue and the large size will fit comfortably around almost any set of ears. The headphones provide just enough isolation for you to easily slip away from the world and enjoy the world as your music makes it. Well balanced: the 50mm drivers are 25% larger Than most headphone drivers, which helps them produce a solid 15Hz 25Khz frequency response, with deep and rich bass, clean and sparkly highs, and expressive vocals. Great sound: life is too short for audio products that don't sound great! We believe that the whole point of listening to music is to hear it as the artist intended. Our engineers and audio experts have spent countless hours listening to and comparing various headphones until we were satisfied we had found models that fit Our demanding standards.

• The soft split-leather ear pads help prevent fatigue and the large size will fit comfortably around almost any set of ears.
• The 50mm drivers are 25% larger Than most headphone drivers which helps them produce a solid 15Hz 25kHz frequency response with Deep and rich bass clean and sparkly highs and expressive vocals.
• Professional sound from everyday headphones. Looks great anywhere you go
• Enjoy clean robust sound across the Audio spectrum
• Perfect for mobile devices hafiz and Audio/video production

User questions & answers

Question:	Usually ships within 1 to 2 months" – This is relevant information? Or two-day shipping is possible
Answer:	they should pair to anything bluetooth since they are bluetooth enabled. Should be good to go.
Question:	Is the audio cable detachable
Answer:	Skullcandy's Ink'd Wireless do not vibrate when a call comes in, whatever you are listening to will pause and your headphones will ring when a call is coming through.
Question:	Is the cord removeable or are they hardwired
Answer:	Thanks for reaching out, Skullcandy's Ink'd Wireless come with small and medium round ear gels.
Question:	do they come with a
Answer:	You can use either bud. I do this all of the time.
Question:	Where can you find replacement ear pads
Answer:	Hi friend, Yes when you open the charging case both earbuds start to pair. If you only take one earbud out, only one will pair with the phone while the other continues to charge or stay ready to use so you can use them separately. Don't worry, buy it, try it and enjoy it now.
Question:	How does the size of the ear cups compare to the DJ model
Answer:	Gracias por su atención, el tiempo de carga es de alrededor de 1-2 horas
Question:	does it have microphone
Answer:	Dear Customer, Yes ! This wireless earbuds is widely compatible with Bluetooth-enabled devices of Android/IOS/Windows.
Question:	how's the bass and do these leak sound
Answer:	Take the earbuds out of the charging case. earbuds will automatically turn on and pair with each other. After the red and blue led of two earbuds flash 2-3 seconds, earbuds prompt pairing successfully,right and left prompt each other.

Product features

Monoprice BT-400 Bluetooth Over Ear Headphone with Qualcomm AptX Support

These Bluetooth Wireless Stereo Headphones deliver hands-free convenience and superb hi-fi sound. Roam wirelessly up to 32 feet away from your paired Bluetooth device and listen uninterrupted for up to 14 hours on a single battery charge. The stylish design, comfortable protein-leather earpads, and foldable design make these the perfect headphones at home, in the office, or on the go.

Bluetooth with aptX

These headphones utilize Bluetooth version 4.1, which provides up to 32 feet (10 meters) of wireless communications range. They feature the Qualcomm aptX audio codec, for superior audio quality when streaming from an aptX-enabled device.

On Ear Controls & Built-in Microphone

The easy-to-use control buttons on the earpiece makes it simple to skip music tracks, adjust the volume, or answer important phone calls. A built-in microphone ensures crystal-clear phone conversations or in-game chat.

Designed For Comfort

These headphones are made of ultra-durable, lightweight brushed aluminum and feature large, cushioned ear cups, an adjustable headband, and a foldable design for complete comfort and portability.

Monoprice Modern Retro Over Ear Headphones

Get professional quality sound from everyday headphones. These 'phones Look great anywhere you go and sound great for hours at a time. It features ultra-comfortable ear pads with a good amount of isolation to keep you focused on the task at hand. Enjoy clean robust sound across the audio spectrum. They are perfect for mobile devices, HiFi, and and audio/video production.

• Ultra-comfortable ear pads with a good amount of isolation to keep you focused on the task at hand
• Perfect for mobile devices, HiFi, and audio/video production
• Enjoy clean, robust sound across the audio spectrum

Ultra-Comfortable

The soft, split-leather earpads help prevent fatigue and the large size will fit comfortably around almost any set of ears. The headphones provide just enough isolation for you to easily slip away from the world and enjoy the world as your music makes it.

Well Balanced

The 50mm drivers are 25 percent larger than most headphone drivers, which helps them produce a solid 15Hz ~ 25kHz frequency response, with deep and rich bass, clean and sparkly highs, and expressive vocals.

Great Sound

Life is too short for audio products that don't sound great! We believe that the whole point of listening to music is to hear it as the artist intended. Our engineers and audio experts have spent countless hours listening to and comparing various headphones until we were satisfied we had found models that fit our demanding standards.

Product description

Get the most out of your home audio system with high quality oxygen-free copper speaker wire from Monoprice!. This wire features two conductors made of high purity (greater than 99. 95% pure) oxygen-free copper. Each conductor is jacketed with color-coded PVC for easy polarity identification. The entire cable assembly is jacketed in a white CL2-rated PVC material. The CL2 rating indicates that the cable complies with fire safety and insurance requirements making it safe for use inside the walls of residential class buildings.

• Lifetime warranty on all cables: with Monoprice lifetime warranty you can rest assured we stand behind our products and our customers.
• Oxygen-free 99.95% pure bare copper conductors
• 250 continuous feet of 14Awg 2-conductor speaker wire | on a spool
• The white Outer jacket is CL2 rated, making it safe for use within the walls of residential class buildings
• Each conductor has an individual, color-coded jacket enclosed within the outer white CL2 jacket

User questions & answers

Question:	The product description says "Clear PVC jacket with a blue stripe to indicate polarity", but the picture shows a white cover. Which is it
Answer:	White, with the two internal leads (red/black) jacketed separately. Exactly what the picture shows.
Question:	Hello, can this be used to power 12v 2A IR Illuminator for IP Cameras
Answer:	I use it to run 12 up yo 30 amps per run on 2 cores for holiday lighting. So yeah 2 amps is nothing on this cable.
Question:	What is the strand count for this wire
Answer:	If purchased through DIY its pure copper 65 strand per conductor
Question:	Is this wire as flexible (meaning easily bendable but has a little spring back) as other speaker wire
Answer:	It is very flexible. For lack of a better word, the rubber sheathing is very "supple". I would call it far more flexible than regular speaker wire.

Product features

Monoprice 102821 Access Series 14 Gauge AWG CL2 Rated 2 Conductor Speaker Wire/Cable

Get the most out of your home audio system with high quality, oxygen-free, pure bare copper speaker wire from Monoprice!

This speaker wire features two conductors made of high purity, oxygen-free bare copper. Pure Bare Copper is a superior conductor to the copper clad aluminum (CCA) conductors used in most other inexpensive speaker wire. CCA is only about 68% as conductive as pure bare copper. This additional resistance is added to the impedance of your speakers and can negatively effect the sound.

For the wire to have no audible effect, the total wire resistance should be no more than 5% of the lowest impedance of your speakers. Even speakers rated for a nominal 8-ohms, may dip to as low as 4-ohms at some frequencies, which further reduces the total cable resistance allowed in the wire. Using Pure Bare Copper speaker wire ensures that the total load put on the amplifier remains as close as possible to the impedance curve of your speakers.

Product description

The Ultimate 2 3D Printer includes a host of features that makes it easier than ever to get perfect 3D prints with a minimum of hassle. The full enclosure helps maintain internal temperatures, ensuring that drafts, air conditioning, and other environmental factors have no effect on the print and making it easier to work with materials like ASA and ABS without fear of warping. The enclosure is lit internally with LED lights, allowing to you monitor the print without the need for a flashlight or other spot lighting. The removable glass build plate provides the flattest surface possible, while the underlying aluminum plate allows the printer to use its built-in inductive sensor for auto leveling. All in all, the Ultimate 2's advanced features and ease-of-use makes it the perfect 3D printer for personal, professional, and educational applications.

• AUTO BED LEVELING: Eliminate the hassles of bed leveling with screws and springs. The built-in inductive sensor can automatically level the print bed, saving you times and aggravation. let makes the print bed absolutely level, ensuring that the first print layers is properly adhere to the build plate. Additionally, each printer is pre-levelled at factory before it ships.
• HEATED AND REMOVABLE GLASS BUILD PLATE: The glass build plate provides the flattest surface possible, ensuring that the first print layers are flawless. The build plate can be heated to 100C, which helps first layer adhesion with materials such as ASA and ABS.
• FILAMENT DETECTOR: With the Ultimate 2, you have no need to worry about running out of filament in the middle of a print. The built-in filament sensor detects when the filament has been consumed and automatically pauses the print, allowing you to load a fresh spool of filament to finish your print. Maximum Power Consumption is 200 watts
• FULLY ENCLOSED: Environmental factors can cause prints to curl, split, or otherwise fail, especially when working with more temperature sensitive filaments. The full enclosure helps maintain internal temperatures, ensuring that drafts, air conditioning, and other environmental factors have no effect on the print.
• INTERNAL LIGHTING: The full enclosure has the negative effect of making it more difficult to see your print, without using a flashlight or other spot lighting. The Ultimate 2 features a row of LED lights inside the enclosure, allowing you to easily monitor your print.

User questions & answers

Question:	Auto resume after Power loss
Answer:	Definitely not.
Question:	Does the printer support petg filaments ? the description mentions pet. i am new to 3d printing so apologize if the question is basic
Answer:	Most PETG filaments *should* print from the extruder in the Ultimate 2. The hot end is designed for temperatures up to 250 degrees C. PETGs easily melt before that.
Question:	Does this really come 100% assembled
Answer:	Yes, besides taking out the protective packaging, it really was remove package, feed filament, fire up cura, start printing
Question:	Is this compatible with carbon fiber or TPU filaments
Answer:	I bought a hardened "Micro Swiss MK8 Plated A2 Tool Steel Wear Resistant Nozzle (MakerBot, CraftBot, Creality CR10, Tevo Tornado) .4mm" to print abrasive filaments. Fits perfect. make sure to re-level the bed after installing. I haven't tried printing TPU.

Product features

Monoprice Maker Ultimate 2 | 3D Printer

The Ultimate 2 3D Printer includes a host of features that makes it easier than ever to get perfect 3D prints with a minimum of hassle. The full enclosure helps maintain internal temperatures, ensuring that drafts, air conditioning, and other environmental factors have no effect on the print and making it easier to work with materials like ASA and ABS without fear of warping.

Auto Bed Leveling

Eliminate the hassle of bed leveling with screws and springs. The built-in inductive sensor can automatically level the print bed, saving you time and aggravation.

Heated & Removable Glass Build Plate

The glass build plate provides the flattest surface possible, ensuring that the first print layers are flawless. the build plate can be heated to 100 °C, which helps first layer adhesion with material such as ASA and ABS.

Filament Detector

The built-in filament sensor detects when the filament has been consumed and automatically pauses the print, allowing you to load a fresh spool of filament to finish your print.

Internal Lighting

The full enclosure has the negative effect of making it more difficult to see your print, without using a flashlight or other spot lighting. The ultimate 2 features a row of LED lights inside the enclosure, allowing you to easily monitor your print