10 best co2 regulator gauges

Product description

Kegconnection offers this replacement 0-2000 PSI gauge for regulators that required left hand thread on high pressure side. This gauge already comes with plumbers tape installed at the factory, so it is ready to install, just screw on your regulator!

• 0-2000 PSI replacement gauge for a regulator requiring a left handed thread
• 0-2000 replacement gauge for regulators that required left hand thread on high pressure side.
• gauge already comes with plumbers tape
• Shipping rate is for the Continental US ONLY.

User questions & answers

Question:	Will this work on a Danby co2 gauge for kegerator
Answer:	It doesn't really matter, you want to turn that screw (zinc) or knob (poly) in the dead center of the regulator assembly counterclockwise before you install the regulator. That screw in the center is what keeps the gas surging thru the dials. once it's installed on the tank you turn it clockwise to open check for leaks and do whatever the instructions tell you.
Question:	Do they sell one with the threads on the other side of the gauge
Answer:	No, there’s a one way valve between the keg adapter and air line
Question:	thread size? I saw another pressure gauge that is 1/4 inch. I need 1/2 inch
Answer:	I ordered a primary for these secondary regulators. yes you need a primary to connect from your main co2 bulk tank to your primary then to secondary and then to fermentors or brite tanks. hope this helps.

Product description

This is a FERRODAY PROFESSIONAL GRADE dual gauge CO2 regulator used for draft beer setups, fits all standard CO2 tanks with CGA-320 inlets. Functioned flawlessly to control and monitor both the output pressure and the cylinder pressure at the same time. The high pressure gauge for cylinder reads between 0-3000 psi and the lower pressure gauge for output reads between 0-60 psi.





Features:

●Heavy duty unit for long term use;

●High-contrast writing for easy reading;

●Manual blow off release valve designed for safety concerns;

●Big ergonomic adjust knob for precise pressure adjustments;

●2 durable tank washers form a tight seal for leakage proof connection;

●Built-in Sintered brass inlet filter keeps harmful contaminants out of the regulator for safety!





Package:

1 x CO2 Regulator

2 x Tank Washer

2 x Clamp





Please! If any problems, we would try our best to serve you!

• 【Top Quality No Leaks】: FERRODAY lifetime CO2 keg pressure regulator features heavy duty forged brass body, exquisitely crafted tank washers and relief valve gasket to prevent any kinds of gas leakage!
• 【Easy to Adjust by Hand】: CO2 regulator has 2 control knobs, one adjustment knob enables more precise control even small adjustments, one shut-off knob allows instantly shut off without liquid backing up gas line, easy to turn.
• 【Lock Ring to Hold Your Setting & Big Gauges Clear view】: A lock ring under the big knob can firmly locked to hold your setting. Two Big gauges can accurately show the CO2 volume in cylinder and the output pressure to keg. FERRODAY keg regulator has crystal clear view for better experience!
• 【Relief Valve & Filter】: Safety first! A sintered metal filter in the stem keeps harmful contaminants out of the regulator. Customized manual relief valve releases pressure at 55-65 PSI each time for further adjustment and safety concern.
• 【Life Time Service】We are committed to offer you with high quality product as well as superior service! Please feel free to tell if any problem, we would try our best to satisfy you. Lifetime technical support.

User questions & answers

Question:	what size is the fitting that goes on the co2 tank
Answer:	Yes, it is.
Question:	I don't know how exactly to use this CO2 regulator. Is there a detailed instruction manual in the package
Answer:	Yes, the hoses are included
Question:	How to adjust the pressure release valve
Answer:	Yes, you have to, they don't come included with the regulator. I paired mine with a Cressi mini console.
Question:	Does this gauge tell u the pressure inside the c02 tank
Answer:	Mine had a yellow, plastic coated, braided hose (similar to air compressor hose) for the octo and a traditional rubber hose for the 2nd stage. Neither are very flexible. I eventually replaced them both with braided hoses.

Product description

MRbrew Double Gauge CO2 Regulator, which has been specially designed to provide maximum convenience and durability in busy commercial environments like bars, tasting rooms, and restaurants.



★The MRbrew Beer Keg Regulator works with any Co2 Tank with a CGA-320 valve.

★Both gauges feature an easy to read design.

★The top gauge lets you know how much Co2 Pressure is in the keg and displays 0-60 psi.

★The second gauge lets you know how much Co2 gas is left inside the Co2 Tank and features a 0-3000 display.



So you'll never be caught off guard by an empty CO2 tank again.



This brewery-grade beer regulator features a multi-stage body for more precise control when making small adjustments to the output pressure.

The first stage reduces the output pressure from the tank to a more manageable pressure, and the second stage fine tunes that pressure for output to the keg



Allowing adjustments to be optimized for the operational range of beer, wine, coffee or whatever you're dispensing. A large adjustment knob allows you to make quick and accurate adjustments by hand and turns effortlessly, even in freezing temperatures.



The regulator body is constructed of forged brass with all brass connections and components, a sintered brass inlet filter, integrated nylon tank connection washer (and spare) and self resetting safety release valve.

★Hose barb end has been designed for use with 5/16" I.D. pressure tubing

★5/16" barbed output for use with 5/16" ID hose

★Integral safety pressure relief valve releases at 45 PSI

★Large hand control makes it easy to adjust the presure inside keg

★Inlet nipple has a permanent thick nylon seal that eliminates one source of leaks, so you will not need to use a new fiber washer every time the tank is changed



👉 Regulators are all pressure tested to assure reliability in the field



🎁 You have 1 Year Warranty Against Manufacturing Defects

• 【PRESSURE YOU WANT】This brewery-grade keg regulator features a multi-stage body for more precise control when making little adjustment to the output pressure. And the lock ring under the adjustment knob can be quickly locked without re-adjustment, and maintains steady Co2 pressure.
• 【NO LEAKS & EASY INSTALLATION】Join our leading assembly technology, our co2 keg regulator ensure fast and stable transmission without leaking. All you need to install this beer keg regulator is an adjustable wrench. Always place a washer between the lock-down nut and the tank to ensure a tight seal.
• 【PROFESSIONAL GRADE】Easy-to-adjust large knob, easy-to-read dual-gauge with 45 PSI safety relief valve and gas shut-off valve, Our regulator for kegerator, which has been specially designed to provide maximum convenience and durability in busy commercial environments like bars, tasting rooms, and restaurants.
• 【HEAVY DUTY & DURABLE】MRbrew CO2 Pressure Regulator for Draft Beer is a heavy duty unit, constructed of forged premium brass with all brass connections and components and features a sintered brass inlet filter, integrated nylon tank connection washer (and spare). Regular replacement of washers ensures long-term use.
• 【100% LIFELONG ISSUES SOLVING FOR YOU】Each MRbrew keg regulator is backed by unbeatable, reliable, trusted product quality, we will unconditionally solve your problems if you are not satisfied!

Product features

MRbrew BRAND HIGH-END HEAVY KEG REGULATOR, AN AMAZING CHOICE FOR YOU!

Product description

WARNING: THIS PRODUCT CAN EXPOSE YOU TO CHEMICALS, INCLUDING LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS AND REPRODUCTIVE HARM. FOR MORE INFORMATION PLEASE VISIT: WWW.PROP65WARNINGS.CA.GOV Robust design delivers performance and reliability. Extremely durable and user friendly polycarbonate bonnets make adjustments a snap. Pull cap to adjust the pressure and push back to lock it in. High CO2 volumetric flow provides continuity in product dispensing. This primary regulator connects directly to its gas source so it's ready to rock. Recommended operating pressure should be limited to 2/3 of the gauge range for maximum accuracy. UL approved per UL252 Class IV rating for CO2. Polycarbonate bonnet will not chip, break or fade. 10 micron filter built in to keep contaminants out of regulators are used throughout the beverage industry. This regulator is the most consistently accurate and well built regulator on the market. This unit stays on pressure even when your CO2 tank level does down. Approved for use by all major beer distributors and Breweries. Shutoff Valve is a ball Type check Valve that prevents product back-flow into the regulator and tank. Solid Brass with extra long nipple. Regulator has pressure safety system (burst at 55 to 60 psi). permanent Quad ring seal on Inlet nipple helps eliminate a source of leaks. no need to use a new fiber washer each time tank is changed. Regulator will be double boxed to avoid any damage in transit

User questions & answers

Question:	Does it come pre assembled
Answer:	This is for any size aquarium. You adjust the flow of CO2 (usually counted in "bubbles per second") based on the volume of water and plant density. You do have to buy the correct sized diffuser to support your tank.
Question:	Hi,Now have tank, regulator, gasline assembly w/ball lock and a carbonator but don't know what to do now. How do I hook into the sodastream w/this
Answer:	Seems to be steel (soft metal) the wrench that comes with this does scratch/tear metal collar that’s screws onto the bottle
Question:	Does this come with a 1/4" or a 5/16" barb? Thanks
Answer:	Make sure the valve on the tank is open. If none of the gauges are moving there is no pressure getting to the valves. An empty co2 cylinder could also be the cause.
Question:	Is this Made in USA
Answer:	Hello David,Yes, this will work with a standard C02 tank and that is the most common tank that mixed/beer gas comes in. This is an excellent choice for a primary, if you plan to run secondary regulators because of the high pressure ability. AnthonyThe Beverage Factory

Product description

WARNING: THIS PRODUCT CONTAINS ONE OR MORE CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER HANDLING. You can use this low-pressure regulator on any CO2 tank with a CGA-320 valve. CO2 tanks have a male thread (CGA-320); these regulators have a female thread. This regulator features dual gauges to measure psi as well as the volume of CO2 in the cylinder, indicating how much CO2 is left in the cylinder and when you should have it refilled. The knob on the front is used to adjust the output pressure. The red polycarbonate bonnet will not chip, break or fade. There is a non-adjustable shut down built into the body of the regulator. The high-pressure ports have left-hand female threads to prevent their use as a low-pressure outlet. The non-removable adjusting screw is designed so that when it is turned all the way in the maximum downstream delivery pressure will not exceed 50psi, with a safety blow off at 60psi. Internal relief valve opens whenever delivery pressure exceeds set pressure by 15psi. This feature serves as a warning that the seat or diaphragm may be worn or damaged and should be replaced. Sintered metal flow control filter in the inlet nipple to prevent dirt and other particles from damaging internal regulator parts. The permanent Quad-Ring Seal on the inlet nipple helps eliminate a source of leaks, so there is no need to use a new fiber washer each time the tank is changed. Outlet features NADS 1600C shutoff which eliminates a source of gas leaks. The duck bill check valve helps prevent product back up into the regulator, a common cause of malfunction in the regulating and relief valve parts. Hose barb end designed for use with 5/16 inch I.D. pressure tubing. All regulators are pressure tested to assure in-field reliability. The seat assembly is easily replaceable, so there is no need to remove the regulator from the tank. Bullets change to: Low pressure gauge (the top gauge) indicates output pressure to the keg The low pressure regulator allows for an adjusted pressure from 1 to 50psi, the maximum downstream delivery pressure will not exceed 50psi High pressure gauge (the side gauge) indicates CO2 tank pressure remaining Duck bill check valve helps prevent product back up into the regulator Assembled and Tested in the USA

• Low pressure gauge (the top gauge) indicates output pressure to the keg
• The low pressure regulator allows for an adjusted pressure from 1 to 50psi, the maximum downstream delivery pressure will not exceed 50psi
• High pressure gauge (the side gauge) indicates CO2 tank pressure remaining
• Duck bill check valve helps prevent product back up into the regulator
• Assembled and Tested in the USA

User questions & answers

Question:	I just hooked this up to my system but gauges arent moving. is it possible co2 tank is empty? should i be doing anything special after hooking up
Answer:	Yes, ours did come with a pressure gauge.
Question:	Confused about the "mixed gas" description. i assume this will work with standard co2 tank? also, can secondaries be added at a later date
Answer:	Yes, ours did include the low-pressure hose for the BCD, as well as, the high-pressure hose for the pressure gauge and the other two low-pressure hoses for both second stage regulators.
Question:	Is there a pressure release valve
Answer:	No, ours does not have an integrated weight system.
Question:	Put the size of the barb on here
Answer:	I've used it as a second stage for my set-up for 5 years and never had it repaired. I've tested it below 100ft and it was easy breathing. It's a great buy. Have a great dive.

Product description

Description:

CGA580 fitting.

ARG/CO2 gauge.

Argon gauge 0 to 4500PSI.

Internal safety pressure relief design.

Plastic adjustment knob for smooth "easy touch" flow settings.

Ideal for commercial, industrial and laboratory applications.



Package:

1 * Argon CO2 Regulators关于此艺术品 Description:

CGA580 fitting.

ARG/CO2 gauge.

Argon gauge 0 to 4500PSI.

Internal safety pressure relief design.

Plastic adjustment knob for smooth "easy touch" flow settings.

Ideal for commercial, industrial and laboratory applications.



Package:

1 * Argon CO2 Regulators

• 1, Designed for MIG & TIG applications and provide accurate regulation of gas flow.
• 2, Features: 2" dual-gauges for easy reading.
• 3, Safe Design: Accurate measurement of gas. Internal safety pressure relief design.
• 4, Specifiction:Brass regulator body; CGA580 fitting, FEMALE 5/8" and MALE 9/16" Outlet.
• 5, Wide Use: Plastic adjustment knob for smooth "easy touch" flow settings; Ideal for commercial, industrial and laboratory applications.

Product description

Specifications: 

- 0-60 PSI Working Pressure

- 0-3000 PSI Tank Pressure

- Better Design of Safety Pressure Relief Valve springs (Inside instead of Outside) also have higher fatigue strength and durability.

- GA 320 CO2 Pressure Regulator light weight,All you need to install this is an adjustable wrench.

- Each CO2 Beer Regulator Pressure Keg regulator is supplied with 2 O-ring washers (One installed inside and the other tied onto the Regulator.

Package Content: 

1PC x Dual Gauge CO2 Regulator

• ❤【Double Gauge】: The top gauge (0-60psi) of this CO2 regulator shows you how much pressure is being provided to the kegs, the side gauge(0-3000psi) of this CO2 regulator shows you how much CO2 is left in your cylinder/tank.
• ❤【Compatible & Safe】: This CO2 regulator works with any CO2 tank with a CGA-320 valve. It comes with a CGA-320 Female thread and a shut off valve allows you to turn the gas flow on / off and prevents liquid from backing into the regulator.
• ❤【Premium Material】: The Draft Beer Dispensing CO2 Regulator adopts to food grade high-strength copper chrome decompression material and sturdy rubber boots that help protect them from damage. And Inside Safety Pressure Relief Valve springs also have high fatigue strength and durability.
• ❤【Easy To Install】: Slap this CO2 regulator on a food grade CO2 tank, connect a gas line ( ID 5/16' or 3/8”) and carbonator, and you have a lot cheaper carbonated water than buying carbonated water bottles directly.
• ❤【Suitable Occasions】: Particularly suitable in a Shop,Bar,Home,Out Door,Plants etc. (Note: Please don’t increase the pressure adjustment knob over 45PSI to prevent leakage.There is a red mark on the dial to notify you.Beer working pressure:10-30PSI.)

Product description

SPARC CO2 regulators are specifically designed for use in draft beer, kombucha, and similar setups. This CO2 regulator is equipped with 2 gauge displays: 1 for showing the working pressure in your draft beer setup as well as 1 for showing the pressure in your CO2 tank. This regulator attaches to standard North American CO2 gas tanks with a male thread (standard CGA-320 connection). The red knob on the regulator lets you adjust the working pressure without any additional tools.

• HEAVY DUTY WITH DUAL GAUGES ✔ Heavy duty unit made with dual gauges to accurately measure working pressure in the system and CO2 tank pressure. Great for kegs, brew setups, kombucha etc.
• PROFESSIONAL GRADE ✔ Our CO2 Regulator fits all standard CO2 tanks with CGA-320 outlets. You can adjust the working pressure in your system via a control knob in the front. Gas Shut Off Valve for easy keg/tank swaps. Safety pressure relief valve + chrome shut off valve to prevent beer or anything else from backing up into the gas lines.
• EASY INSTALLATION ✔ All you need to install this CO2 Pressure Regulator is an adjustable wrench. Each unit is supplied with 2 O-ring washers. Always place a washer between the lock-down nut and the tank to ensure a tight seal. Replace washers as needed.
• VERSATILE APPLICATIONS ✔ Works with 15.5 Gallon Kegs, 5 Gallon Kegs, 1.75 Mini Kegs, Half Barrels and Quarter Barrel Units. Barbed gas outlet fitting allows easy connection to many gas line types.
• WE'VE GOT YOUR BACK ✔ Backed by our rock-solid 2 year warranty against manufacturing defects. We are based out of Denver, CO and offer customer service and support via phone, text, and e-mail.

User questions & answers

Question:	Do you have one 0 to 120 psi
Answer:	i do not understand your question. u mean u use a compressor intead of a tank?
Question:	Does output regulator goes between 0 and 60 psi
Answer:	Yes.. with the proper fittings. mine works great
Question:	what size tubing is this regulator designed to be attached to
Answer:	We use at 100 psi on a oilless compressor.

• Accurate measurement of gas.
• Brass regulator body.
• 2 dual-gauges for easy reading.
• CGA580 fitting, FEMALE 5/8 and MALE 9/16 Outlet
• Designed for MIG TIG applications and provide accurate regulation of gas flow.

User questions & answers

Question:	is it really manufactured by Taprite? it looks a bit different from the one they have in their site (logo ect
Answer:	No. This brush is perfect for little hands.
Question:	Is this a lefty tighty threaded item? And what size is the threads
Answer:	It is a cute hair comb and has worked well for a 3-5 year old, though it is a little award for her to hold. It is likely easier for adults to manage/handle.
Question:	The gauge i just received reads 10 psi with no pressure. is there a way to adjust this offset or do i have a faulty gauge
Answer:	good quality, with strong bristle

Product features

Description

- Designed for MIG & TIG applications and provide accurate regulation of gas flow.

- 2" dual-gauges for easy reading.

- Accurate measurement of gas.

- Brass regulator body.

- CGA580 fitting.ARG/CO2 gauge.

- Argon gauge 0 to 4500PSI.

- Internal safety pressure relief design.

- Plastic adjustment knob for smooth "easy touch" flow settings.

- Ideal for commercial, industrial and laboratory applications.

Product description

(WARNING: THIS PRODUCT CAN EXPOSE YOU TO CHEMICALS, INCLUDING LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS AND REPRODUCTIVE HARM. FOR MORE INFORMATION PLEASE VISIT: WWW.PROP65WARNINGS.CA.GOV) Primary Beer Regulator, 1P1P, CGA320 Inlet, 5/16\\" Barb Shut off w/Check, 60 PSI and 2000 PSI Gauges

• Primary Beer Regulator for Home Dispense.
• CO2 regulator has 2 gauges, a 1/4 barbed shutoff valve, and pressure relief valve.
• Includes a washer and is ready to attach to a CO2 tank.
• 1P1P, CGA320 inlet, 5/16" Barb Shutoff, 60 lb and 2000 lb gauges.

User questions & answers

Question:	Is the barb removable
Answer:	The shutoff fitting with barb is removable, it has 1/4" npt pipe threads. While it can be removed, any alteration to the product does void the manufacturers warranty.
Question:	I purchased a duel kegorator for hubby and read that it may be best to change the single regulator that it comes with to this duel...should I
Answer:	This is a great regulator so sure but he will need a way to hook up co2 to 2 kegs so either get a y splitter for this, a 2 co2 distribution block or the dual body taprite
Question:	For a nitrogen draft beer dispensing, are these regulators safe (food grade)? Can you use any nitrogen regulator, or is there such a rating as food gr
Answer:	You can use any regulator that's made to distribute nitrogen and will fit your equipment. Contact time with the regulator is nonexistent. If you want food grade then the gas you buy has to be rated for the food industry.
Question:	Will this screw onto a 20 oz tank typically used for paintball guns? Or will I need an adapter
Answer:	You will need an adapter at attach a paintball tank. Please feel free to contact us at 877-909-BREW(please leave a message) if you have any other questions or would like to inquire about having both parts shipped together. Thank you