12 best deck stain removers

Product description

#1 Deck Wood Stain Stripper is a biodegradable, ready-to-use liquid that quickly removes worn finishes to restore wood surfaces. Stains and varnishes are removed along with collected dirt, mold, mildew and mill glaze. This product is step 1 of a 3 step system. #1 Deck Wood Stain Stripper removes most oil and latex based finishes including: clear film-forming varnishes, polyurethanes, and semitransparent stains. Limitations: #1 Deck Wood Stain Stripper is not designed to strip paint or other film forming surface coatings. To use, simply apply the product a damp surface using a pump-up garden type sprayer, or a car wash type brush. Allow it to set for 15-25 minutes, then scrub if necessary using a stiff bristle brush, and rinse. Using a pressure washer to rinse this product will eliminate any need for scrubbing, however particular care should be taken with a pressure washer to avoid damaging the wood. After rinsing, use #1 Deck Wood Brightener to neutralize the surface and open the pores of the wood so the stain can absorb properly into the wood.

• Removes existing, weathered, semi-transparent stains and sealers
• Ready to use, fast and effective - covers 100-150 sq. ft. per gallon
• Deck stain remover strips worn finishes off decks, fences, and wood siding
• Improves adhesion of wood stains & restores the natural look of wood decks
• For best results, rinse with a pressure washer. Note: This product will not remove paint.

User questions & answers

Question:	will the solution clean the deck pickets? Or will it side off
Answer:	Yes, it can be used on the face and scalp. The 0.3 roller is wider than our face roller (0.25) and was designed to be used on the body, but it can be used on the larger face areas (cheeks and forehead) and scalp if desired.
Question:	Will it remove green matter? Or shoud it be removrd then use your product? Thank you
Answer:	If you look at most of the answers saying it doesnt work, they are mostly the same person. I would think if you JUST rolled for a month that you might not see results. Micro derm rolling is meant to be combined with a skin care regimen to make your products (serums/moisturizers etc) work better by penetrating the top layer of your skin. It is recommended to start out slow and build up to every other day as your skin gets used to it. If you are using any nighttime moisturizer, oil or serum I highly recommend this product!! Just make sure to roll first and then apply your sin care products :)
Question:	will this work on a tongue and groove porch ceiling
Answer:	No it isn't painful since the needles are extremely tiny but you do have to start out slowly so your skin has a chance to get used to it. I have very sensitive skin and it gets red after but goes away in a few hours. And my moisturizer goes a lot deeper when your pores are open.
Question:	Will it remove solid color stain
Answer:	It doesn't work. Sorry. : ) Just put oil on your thighs, or a good lotion, eat the amount of protein for. your body weight, and exercise your thighs.

Product features

About SaverSystems

At SaverSystems, we understand the frustration people feel when they see what they've built deteriorate from the elements. Property is one investment you can bank on, but if it's made with concrete, masonry, or wood it needs to be protected. SaverSystems employs state of the art technology to help protect and save what you build.

SaverSystems has manufactured premium quality, water repellents and protective coatings for over 30 years. We make coatings for a variety of surfaces including wood, concrete, masonry. In addition to the DEFY brand, SaverSystems also manufactures ChimneyRx, MasonrySaver, & ChimneySaver branded products.

All of our products are manufactured in our production facilities located in Richmond, Indiana. Every product is produced under strict quality standards and formulated with the highest quality raw materials available. Our innovative solutions and coatings have stood the test of time, and are trusted by industry professionals and homeowners alike.

User questions & answers

Question:	hello, the information on the Defy website says it can be applied with a roller - any special type? eg what nap to use? thanks
Answer:	I a not tried it on a vertical surface, but I would like to think that with frequent brushing it would be effective.. I hope this has helped you make a positive decision, because it is a good product..
Question:	Does the Defy stripper work well on Thompson's deck stain/sealer
Answer:	Not for sure what your referring to as far as green matter. Mold? This product is supposed to strip stain from wood. If this chemical can not penetrate into the wood because of "green matter" , then yes it should be removed first. Hope this helps
Question:	Will the stripper remove the paint from my doors and side of house? Do I need to cover the house siding and doors before stripping deck
Answer:	It is made to work on wood . I used it on my deck and let it sit for time allowed. The product didn’t remove all the finish. If you can get it up there to sit for a while it may work but you will have to get it into the cracks
Question:	will this strip current stain?? i need to finish using defy wood stain and have a mismatch in color from a previously stained fence
Answer:	Yes, but this is not easy at all and requires multiple coats and multiple powerwashes

Product features

About SaverSystems

At SaverSystems, we understand the frustration people feel when they see what they've built deteriorate from the elements. Property is one investment you can bank on, but if it's made with concrete, masonry, or wood it needs to be protected. SaverSystems employs state of the art technology to help protect and save what you build.

SaverSystems has manufactured premium quality, water repellents and protective coatings for over 30 years. We make coatings for a variety of surfaces including wood, concrete, masonry. In addition to the DEFY brand, SaverSystems also manufactures ChimneyRx, MasonrySaver, & ChimneySaver branded products.

All of our products are manufactured in our production facilities located in Richmond, Indiana. Every product is produced under strict quality standards and formulated with the highest quality raw materials available. Our innovative solutions and coatings have stood the test of time, and are trusted by industry professionals and homeowners alike.

Product description

The MiracleMist MMIC-1 Instant Mold and Mildew Stain Remover goes to work instantly, cleaning before your eyes! This no-scrub formula is a smart cleaner. Its multifunctional chemistry contained in the 1 gal. container allows wetting agents to penetrate deep into hard and soft surfaces, lifting years of dirt, grime, mold, mildew, and algae to the surface where a modest amount of bleach and detergents contained within the formulation removes the stains permanently! Just rinse with light water and your job is done!

• LIFTS YEARS OF STAINS: MiracleMist Instant Mold & Mildew stain remover goes to work instantly, cleaning before your eyes! Its multi-functional chemistry allows wetting agents to penetrate deep into hard and soft surfaces, lifting years of dirt, grime, mold, mildew, and algae to the surface where a modest amount of bleach and detergents remove the stains permanently! Just rinse with light water and your job is done! Just look at everything MiracleMist can clean
• RESULTS IN SECONDS: What could be easier than simply applying a product and watching it work in seconds? That’s what you can expect when you use MiracleMist. Simply spray and rinse 30-60 seconds later! Your surface will be free of black mold, mildew, and green algae stains within one minute of application. Guaranteed
• CONCENTRATED CLEANER: Bleach-based cleaners are used for all sorts of cleaning applications. Many times, store-bought bleach cleaners contain 4% or less in active ingredients. MiracleMist is 25-40% stronger, insuring a better clean. Additionally, MiracleMist contains a special blend of detergents that lift embedded contaminants to the surface where the bleach finishes the job. Are you currently using a bleach cleaner? Replace it with MiracleMist. Get better results. Get the clean you want
• INDOOR USES: Inside the home - easily removes mold and mildew stains from drywall and ceiling, cleans tile & grout, removes mold stains from plastic shower curtains, cleans and restores vinyl flooring.
• OUTDOOR USES: Removes mold, mildew, & algae stains from outdoor furniture, cleans all types of siding including stucco and stone, all types of decking, including composite decking, all types of roofs, including shingle, shake, and metal, and restores wood to near new condition. Also great for RVs and boats!

User questions & answers

Question:	Will this get leaf stains off of my concrete driveway
Answer:	I used 3/4" to get best coverage and to get between planks. Shorter nap did not do as well. In the end, I applied the Defy with a two gallon tank sprayer - much faster and easier.
Question:	Is this product basically just watered down bleach
Answer:	It works really well but you are going to have to brush the deck and power wash it but it will take off the waterproof i had 2 applications of stain and it took it all off
Question:	Is this safe for use in shower? Will it work for caulking? Tile
Answer:	I used it on vinyl siding and exterior housepaint that had dried stain on it. It did not damage the paint or the colored siding.
Question:	Can this product be used around lakes
Answer:	Yes. See this info from www.deckstainhelp.com "Defy Exterior Wood and Deck Stripper is designed to remove transparent and semi-transparent exterior wood and decking stains. Defy Stripper is a biodegradable deck stain remover that restores wood to a like new appearance that will work on both water-based and oil-based stains. Defy Wood Brightener is needed to neutralize after using the stripper"

Product description

For over 14 years, Florida Laboratories has been dedicated to continually improving existing formulas and developing new products to meet market needs. We are committed to ongoing research for new and improved products and have implemented continuous laboratory quality assurance testing of all products to confirm the high standard we expect from our raw materials and finished products. We are pleased to offer you the finest raw materials available for your needs on the planet.You are buying One bag of Two Lb. (2 Pound) of OXALIC ACID 99.6% Purity. Warning: Keep away from Children. If in contact with skin or eyes, wash with running water. If inhaled, move person to fresh air. If ingested, drink water to dilute material in stomach. Use Gloves and Protective Mask. Instructions and Measurements not provided.

• OXALIC ACID 99.6% PURE (Dihydrate)
• Deck, Crystals and Metal Cleaning
• Rust Removal, Wood Stain Remover and More!
• Usage instructions found underneath product picture. If you do not see the instructions you are looking for, simply send us a message and we will respond with the information requested.

User questions & answers

Question:	does it remove pet stains in wood
Answer:	Sorry don’t know I use it to treat mites for bees
Question:	Is this a good product to use for removing rust stains on pavers and travertine? What is the mix ratio
Answer:	I have successfully used about a tablespoon per quart of water for removing paver/concrete rust stains.
Question:	Can you use this on a metal rusted roof
Answer:	I have used it on metal corrosion on our fleet of sailboats for years and have been very pleased with the results. I have tried other products and found that almost nothing else works. If you plan to repaint after removing the rust/corrosion you will need to make sure your wash the surface several times with fresh water. For stubborn areas, you may need to do a little wet sanding with very fine sandpaper (300 GRIT or higher). If you have any wood in the area that you don't want bleached (e.g. a wood deck or stairs) you should cover it and then hose it down as soon as possible if any of the oxalic drips on it.
Question:	How does one prepare and apply this product? Is the water/product mixture paste-like or watery
Answer:	Dissolve it in hot water. Will be watery. Scrub hot solution in with a brush. Then make sure you clean it up with water after don’t leave any residue.

• GET RID OF STUBBORN MOLD AND MILDEW STAINS: Our instant spray cleaner removes the stains left behind from black mold and mildew. They tend to leave behind ugly staining that can go deep below the surface
• REMOVE UNWANTED ODORS: Keep your home free of musty, damp smells that are usually left behind by other sprays; Our spray is great to use in the kitchen, toilet area, drywall and on vinyl shower curtains
• FAST-ACTING SPRAY: Our fast-acting mold stain remover spray, instantly targets deeply embedded stains that linger between bathroom tiles, in grout lines, under the sink, and on shower doors
• NO SCRUBBING NEEDED: Simply spray our ready-to-use formula on the affected area and watch the stains disappear right before your eyes!
• SAFE TO USE ON MULTIPLE SURFACES: Easily remove stains from bathtubs, decks, wood, vinyl siding, drywall, concrete floors, brick walls, kitchen and bathroom tiles and other areas where mold and mildew tend to grow

User questions & answers

Question:	Is it safe to use on air conditionin coils
Answer:	I dont know I have used it in my shower, and on the canvas of my popup camper
Question:	Is this for indoor use only
Answer:	It has something else in it that makes it work, it worked great the first four times I used it , then like all the other I have tried, it didn't, I suggest buying the smallest one you can get, and hopefully you can use it all, stuff works fantastic, until whatever the miracle stuff is disappears
Question:	Can this product remove the yellow rust stain from house siding
Answer:	Yes just rise w fresh water after it has bleach in it
Question:	Can this be used on an asphalt shingled roof to remove mildew stains
Answer:	Yup

Product description

Simple Green Oxy Solve Total Outdoor Cleaner lifts dirt, grime and stains from mold, mildew, moss and algae. The pressure washer concentrate is ideal for cleaning wood, composite, vinyl, metal, fabric, plastic, wicker, concrete, stone, brick, asphalt and other outdoor surfaces, with afast-acting foam that cleans using the power of peroxide. The safer, non-toxic and biodegradable formula meets the rigorous criteria of the U.S. EPA's Safer Choice Program and will not harm surrounding plants, lawns, pets or wildlife. Brighten and renew surfaces without harmful bleach while lifting tough tree sap, grease and oils and removing oxidation and weathering.

• Cleans a wide variety of surfaces such as wood, composite, vinyl, metal, fabric, plastic, wicker, concrete, stone, brick and asphalt
• Lifts dirt, grime and stains from mold, mildew, moss and algae
• Uses the power of peroxide to lift grime without harsh chemicals
• Safer, orally non-toxic formula
• Pressure washer concentrate cleans up to 6,400 sq. ft.

User questions & answers

Question:	Does it work to get cigarette smoke off white doors
Answer:	OK just realized what you are looking for. The Sheath is the heavy clear plastic cover already ove the trimmer's blades. If you look at the sheath at top by handle of trimmer there are a couple snaps to open it and close it. It is plastic but the price was great. I am just very careful when I remove and recover my trimmer and it's doing it's job just fine. :)
Question:	Can this be used on Hardie board
Answer:	No. Look at the picture. I have it. It doesn’t suck it in just blows out so you can blow the leaves away.
Question:	is this safe for automobiles and trucks
Answer:	First the "losing my mojo " question, now maximum penetration? I'm "detecting" a trend!!!
Question:	Will this work well as a car soap
Answer:	Best to use Duracell (4) AA batteries. They should last 20-24 hours if new. Keep recirculating them as they loose power within the unit for max. use. I always keep an extra set in my carrying case for back-up and change after the ones in my unit are about 1/2 life left. You can use rechargeable but they won't last as long and you need to charge them up before you go out for max. efficiency. Happy Hunting!!!

Product features

Oxy Solve Total Outdoor Pressure Washer Cleaner - Removes Stains

Simple Green Oxy Solve Total Outdoor Cleaner lifts dirt and stains from mold, mildew, moss and algae from outdoor surfaces such as wood, plastic, concrete and more. Cleans using peroxide to brighten and renew surfaces without bleach.

Product description

Directions: Wet deck with water. Squirt Star brite Non-Skid Deck Cleaner over the surface to be cleaned and spread evenly with a deck brush. Allow to sit for 2-3 minutes. Scrub the treated area with a deck brush and then rinse well. Allow cleaned area to air-dry. Extremely dirty surfaces may require a second application.

• A very effective, all-surface cleaner for fiberglass, vinyl, plastic, rubber, metal and painted surfaces
• Special chelating agents lift dirt and spills without the need for heavy scrubbing
• Protective polymers provide a barrier against future stains, making clean up a breeze
• Also ideal for cleaning non-textured areas and will not remove wax or polish
• Star brite products are proudly made in the United States since 1973

User questions & answers

Question:	How long is this product good for? (is there an expiration date
Answer:	Hi NOLA Shopper! Oh my goodness! That sounds gnarly! We would not see a problem removing the blood stains, our product should make easy work of cleaning the deck boards. We would recommend using the product at a lower dilution ratio, like 1:1 or 1:2 - even full strength spraying on the blood stains after wetting the deck boards. Work the cleaner into the boards with the deck brush provided. The deck brush in our kit will work well in getting the blood loose of the boards. Be sure to fully rinse after application and cleaning. Please let us know if you have any other questions! - The DeckMAX Team
Question:	Will this work on a pontoon boat floor "carpeted
Answer:	Yes! This will help reduce the appearance of grease spots if not completely remove them from your deck boards!
Question:	Is this biodegradable? I may need to return it if it's not safe for the environment as the boat sits in the bay water. Thanks
Answer:	Simple Green Oxy Solve solutions are all very similar and can be used on a variety of surfaces.
Question:	Is this product biodegradable? Will it harm the invironment if I get it in the water
Answer:	It should not based on my experience with using this product! Michael

Product features

Non-Skid Deck Cleaner With PTEF

Non-Skid Deck Cleaner with PTEF is the most effective and easiest way to clean textured fiberglass, wood, composite and painted decks. The special chelating agents loosen dirt and spills without the need for heavy scrubbing. The PTEF polymers provide a barrier against future stains, making clean up a breeze. It also is ideal for cleaning non-textured areas as well as all fiberglass, vinyl, plastic, metal or rubber surfaces.

DIRECTIONS

Wet deck with water. Squirt Star brite Non-Skid Deck Cleaner over surface to be cleaned and spread evenly with deck brush. Allow to sit for 2-3 minutes. Scrub treated area with deck brush and then rinse well. Allow cleaned area to air-dry. Extremely dirty surfaces may require a second application.

Product description

Wet and Forget has a unique combination of biodegradable selective surfactants for moss removal, mold removal, mildew and stain removal on any exterior surface. When diluted with water and applied, it immediately attacks that unsi moss, mold, and mil. 1 Gallon of Wet & Forget makes 6 gallons of ready to use product, which covers approximately 750-2250 square feet depending on the porosity of the surface

From the Manufacturer

Wet and Forget has a unique combination of biodegradable selective surfactants for moss, mold and mildew stain removal on any exterior surface. When diluted with water and applied, it immediately penetrates the unsightly stain. Each time it rains, this safe, cleansing combination reactivates to gently lift the moss, mold and mildew stain without damaging the surface. Wet and Forget is an EPA approved one step process that requires no scrubbing or rinsing. It is non-acidic, non-caustic and contains no bleach. Be patient, Wet and Forget's gentle cleaning action takes time depending on how heavy the stain is and results are visible over time. Remember good things take time, and Wet and Forget continues to clean for up to a year. No special equipment is required. Just apply Wet and Forget with a pump-up garden sprayer. After the first application simply reapply Wet and Forget at the first sign of moss, mold and mildew stains returning. Wet and Forget can be used on any outdoor surface. Some examples of these surfaces are: asphalt (blacktop), Astroturf, aluminum siding, awnings, brick pavers, composite decking, concrete, driveways, docks, fiberglass boats, fiberglass shingles, fiberglass hulls/topsides, green houses, gutters, inflatable dinghies, limestone, marble, marinas, natural stone, outdoor furniture, outdoor planters, paint surfaces, patios, patio furniture, plastic houses, recreational vehicles, retaining walls, sails, sandstone, shade sails, sidewalks, stucco, tennis courts, teak decks, textured finishes, tiles, tombstones, umbrellas (outdoor), vinyl siding, wood.

• Non-caustic, Non-acidic, Contains no bleach
• Safe on any outdoor surface
• One step process. For concrete, brick, stucco, aluminum, painted surfaces, siding, decking, roofs and more
• No scrubbing or rinsing required
• Not for sale in California

User questions & answers

Question:	apply wetandforget prior to restaining
Answer:	I have only applied it after staining. I suggest you contact the manufactureran ask your question.
Question:	Any luck with this cleaning mildew off of painted brick
Answer:	Used on roof, vinyl siding, painted concrete. Found it to be better than other products that made similar claims, just use as instructed.
Question:	Can I spray thiis on my back deck today, and paint the deck 4 days later without washing
Answer:	Wet & Forget does not work that fast. If you were to paint your deck four days after applying this product you would be wasting your money because Wet & Forget would not work at all. In order for Wet & Forget to work it must be exposed to the elements, e.g., sun and rain. I would pressure wash the patio lightly, let it dry completely and then paint or stain it.
Question:	Any luck with just dirty landscape bricks or is it just for mold and mildew
Answer:	I doubt that W&F would clean ordinary dirt, soil, grease, and similar stains from landscape bricks, but it does do a great job of removing mold, mildew, fungus, lichens, moss, etc. My experience with W&F is that when it kills the mold, mildew, fungus, moss, etc., with time the deposits of discoloration that those organisms put on the surface will also come off. I have an area of pavers by the side of my house that is in the shade almost all year so it tends to grow mold/mildew and lichens. When I apply W&F, almost immediately the mold/mildew changes color from black to brownish color, and gradually after a few weeks the brownish color goes away, too. Similarly with lichens and moss: First it changes from live green color to a dead brownish color, and then it goes away completely. This stuff is fantastic for killing "dirty" organisms like mold and mildew and also for removing most of the stains they leave behind, but it won't clean ordinary soil, grease, etc.

Product features

Wet & Forget, making life easier and cleaning smarter.

Life's busy. We hear you. That's why the entire line of Wet & Forget products were developed with you in mind. Our products are easy to use, and they do the cleaning for you. Simply apply the products and get back to living.

Easy:

Wet & Forget products simplify cleaning with spray and leave, spray and rinse, or spray and wipe applications. We’ve eliminated the time commitment, scrubbing, and harsh chemicals associated with conventional cleaning products.

Smart:

We’ve designed our smart bottles and sprayers to allow for faster, more thorough coverage. Turn the triggers any angle without disrupted product flow. Triggers and proprietary nozzles reach extreme heights so you can keep your feet firmly planted on the ground.

Product description

Smart strip is a revolutionary paint remover that is safe for the user, any substrate and the environment. It is formulated without methylene chloride and is non-carcinogenic, non-toxic and non-caustic. This water-based stripper will effectively remove up to 15 coats of virtually any coating like oil-based, water-based, acrylics, varnishes, urethanes even old lead paints from interior or exterior surface of wood, brick, stone, concrete, plaster, metal, plastic, glass, fiberglass, etc. Smart strip has zero VOCs, is odor free, user friendly, 100-Percent biodegradable and pH neutral. This is a water-based paste that is easily applied by brush, roller or conventional airless spray. Allow the paste to dwell on the coatings for 3 to 24 hours, depending on the number of coats and the type of coatings being removed. It is formulated to remain wet and effective over extended periods of time and does not require the use of Peel Away Paper. After appropriate dwell time, remove the paste and the softened/lifted paint using a scraper. Any remaining residue can be removed with a sponge and water or a power washer. There is no need to neutralize the stripped surface. Available in 1-quart can.

From the Manufacturer

Smart strip is a revolutionary paint remover that is safe for the user, any substrate and the environment. It is formulated without methylene chloride and is non-carcinogenic, non-toxic and non-caustic. This water-based stripper will effectively remove up to 15 coats of virtually any coating like oil-based, water-based, acrylics, varnishes, urethanes even old lead paints from interior or exterior surface of wood, brick, stone, concrete, plaster, metal, plastic, glass, fiberglass, etc. Smart strip has zero VOCs, is odor free, user friendly, 100-Percent biodegradable and pH neutral. This is a water-based paste that is easily applied by brush, roller or conventional airless spray. Allow the paste to dwell on the coatings for 3 to 24 hours, depending on the number of coats and the type of coatings being removed. It is formulated to remain wet and effective over extended periods of time and does not require the use of Peel Away Paper. After appropriate dwell time, remove the paste and the softened/lifted paint using a scraper. Any remaining residue can be removed with a sponge and water or a power washer. There is no need to neutralize the stripped surface. Available in 1-quart can.

• Biodegradable formula
• Safe for user, substrate and environment
• Removes multiple layers
• Odor free water based advanced paint remover
• Formulated without methylene chloride and is non-carcinogenic
• Odor free water based advanced paint remover
• Formulated without methylene chloride and is non-carcinogenic

User questions & answers

Question:	has anyone use this in a sprayer
Answer:	It can be sprayed. Best to use a commercial sprayer. You will need to remove all the filters and use a .031 tip size.
Question:	how does it do on wood
Answer:	It does very well on wood. Unlike some other environmental strippers like Peel Away 7 it isn't highly alkaline and doesn't require being neutralized, and thus there is no danger of darkening the wood. The #1 choice for wood in my opinion, and I have tried virtually everything. (One tip--cover the stripper with wax paper, plastic, etc. while you let it work so it doesn't dry out. Let it work overnight for maximum effectiveness.)
Question:	How many gallons would be needed for a 26 ft boat with a 10 ft beam
Answer:	I think you would need to ask to buy it by the barrel! We stripped both sides of a standard door and used over a gallon. There were many layers of paint, but you also have to put it on thickly for it to work properly. I would contact the manufacturer for suggestions on stripping a boat.
Question:	does it work on brick which has latex paint on it
Answer:	Yes it works great on stripping latex paint from brick interior or exterior.

Product description

POUR-N-RESTORE COMPOSITE DECK SPOT REMOVER *32 oz. *Removes staining from food, grease, cooking oil, wax, algae and more *Apply as a liquid and dries to a powder as it lifts and captures stains through micro-extraction technology *Just apply, let it dry and sweep it up *Does not discolor composite decking (Neutral PH) *Biodegradable formulation *Bottle

• Restore Composite Deck Spot Remover Neutral 32 Oz

User questions & answers

Question:	Will it remove sunscreen stains
Answer:	Yes
Question:	Can I use this to remove gorilla glue from my deck without striping the stain on the boards
Answer:	Yes with some mild brushing after application. I would not use this due to local oxidation removal in the treated area.
Question:	Will it cause white spots on red colored decking
Answer:	This product is absolutely safe for automobiles and trucks. It can be used in a pressure washer or manually.
Question:	Can i change the color of my, trex deck by painting it
Answer:	This product does not work the same way as car soap, although it can be used to wash a car. The chemistry is geared toward environmental pollutants, dirt and some road grime. It is not a degreaser, so if road tar, grease and oil are the issue using regular Simple Green All Purpose Cleaner or Simple Green Pro HD might be more effective.

Product description

The Perdura DECK BOSS professional deck stain brush applicator cuts your coating time in half. (pole not included)



Professionals report savings of over $150 on one standard sized deck stain project which is about triple the cost of a DECK BOSS.

This means purchasing a DECK BOSS is the best investment you could make and a must have product for any professional or DIY customer.



Buy a DECK BOSS today, use it and you will understand why Perdura Pro Series Brushes are the best deck stain tools on the market today!



Perdura Pro Series DECK BOSS is an Australian brand and our business focus is simple, supply the best quality brushes on the market while giving the best customer support and service.

Perdura Brushes are sold in many countries around the world, are loved by professionals and have a strong following with customers who are focused on quality and performance.



The DECK BOSS is the ULTIMATE tool for coating or staining large areas FAST! You can load up lots of paint, stain or oil with the 7 x 2 inch design which has a 3 inch filament length.



The DECK BOSS will outlast other brushes on the market and will save you lots of money when compared to deck stain/paint pad application tools.

Pads and rollers are a throw away item whereas the DECK BOSS just requires a simple clean and can be used again and again.



Quality never goes out of fashion so choose Perdura for better value and results!

• ✅ FINISH your DECK STAINING in HALF the TIME and SAVE YOUR BACK in the process - The DECK BOSS is FUN to use and the PROVEN PERFORMER in the U.S. professional deck staining market. - Load up, back brush and coat between cracks in the one action - SUPER FAST application of all paints, stains, sealers to rough or smooth surfaces. (pole not included)
• ✅ PROFESSIONAL MONEY MAKING MACHINE - In the hands of a Professional, the DECK BOSS will save lots of time while providing a higher level of finish. This means more money in your pocket and is an absolute weapon that all Professionals and DIY's should have at home or in the van.
• ✅ #1 RATED DECK STAIN/PAINT BRUSH ON THE MARKET - A must have coating tool for any professional or DIY - See what our Professional and DIY customers are saying about DECK BOSS from the reviews.
• ✅ LOVE the DECK BOSS or return it - Try the BEST RATED Deck Stain Brush on the market 100% RISK FREE - We are so confident this will be the BEST Deck Stain brush you have ever used and will want to tell everyone about - We also provide the Perdura 100% QUALITY ASSURANCE - Superior build - long lasting custom Australian design built to last - Makes a great X-Mas, Birthday, Fathers Day or any day gift for the professional or DIY. (pole not included)
• ✅ FREE BONUS CASE, Brush Comb and Can opening Keyring - Your DECK BOSS pack comes in a hard protective box that looks great and can be used to store after use. We also include a handy DECK BOSS brush comb and can/bottle opener keyring.

User questions & answers

Question:	Can i use a clear deck sealer with it
Answer:	Yes you certainly can! You can use any paint stain or sealer both water and oil based, clear or with pigment for rough or smooth wood surfaces and concrete applications. All the best from Perdura Brushes Australia!
Question:	I will need to get a handle – do you have any particular one to recommend? One more question – I will be using stain that contains oil, what is the be
Answer:	I just used a handle that was on a floor broom/mop.
Question:	Will this work on railing, or is it too large
Answer:	The DECK BOSS is too big for working on rails so for this application, we recommend using the smaller RAPID STAIN brush which is 5 x 1 inch and designed for hand use. Best regards, Perdura Brushes Australia
Question:	What poles do I need to purchase for it
Answer:	The DECK BOSS has a universal thread so will be compatible with most paint poles and even household brooms. It's highly likely that most customers will already have a pole that will fit in their broom cupboard or shed. For professional use, we use a light weight pole with a length of 5-6 feet. Best regards and feel free to contact us again with any further questions.

Product description

The mold and mildew stain and odor removal solution for professionals

RMR-86 PRO is our most powerful mold stain cleaner. It will deeply penetrate tough to remove mold and mildew stains and lingering odors instantly using a unique hybrid of pure sodium hypochlorite. The deep-cleaning action breaks apart stubborn stains embedded in wood substrates, floor joist, wall studs, drywall, concrete, vinyl, tile & grout, dissolving them quickly and easily, while removing all visual stains left behind from mold and mildew.



Contractor grade formula for multiple surfaces

RMR-86 PRO is an indispensable stain remover for those deeply embedded stubborn mold stains. Our professional grade formula is handy for keeping office buildings, remodels, recreation areas, commercial kitchens, and public restrooms stain free. Remove tough stains from patio or deck areas, wood or concrete floors in the basement, damp brick walls or pathways, kitchen cabinets, bathroom tiles and other areas where mold and mildew tend to grow at a rapid pace.

• TACKLES TOUGH MOLD STAINS INSTANTLY: RMR-86 PRO is our most powerful mold stain remover that utilizes special deep penetrating surfactants with a unique hybrid of pure sodium hypochlorite to remove stubborn stains in just seconds
• CONTRACTOR GRADE: Our extra strength stain removal solution is specifically created for professional use and is 5x stronger than other stain removal products on the market
• READY TO USE: Our ultra strength formula is ready to use and instantly dissolves difficult mold and mildew stains without scrubbing or sanding to get the job done quickly and efficiently, saving you both time and money
• FAST-ACTING FORMULA: Our easy to use liquid stain remover instantly targets deeply seated stains that linger in damp or dark places
• SAFE TO USE ON MULTIPLE SURFACES: RMR-86 PRO removes tough stains quickly from attics, crawlspaces, wood, concrete floors, brick walls, plywood, drywall, decks and other areas where mold and mildew tend to grow

User questions & answers

Question:	Can I use this in my attic on rafters and underside of roof sheathing? Is it okay for the roofing nails that penetrate the plywood
Answer:	Some work areas like outdoors are already well ventilated, so skin and eye protection are mainly needed. Especially indoors, we still always recommend wearing full PPE when applying RMR-86. This includes a hooded tyvek or a chemical poly coated suit, full face respirator with P100 organic vapor and acid gas cartridge filter and latex gloves.Please let us know if you have any further questions. Thank you.
Question:	Can RMR-86 pro be used on acrylic bathtub
Answer:	Good Morning, you should not use RMR-86 in a commercial fogger and it should be sprayed directly on the surface. If you have any further questions, you can reach us at 866-822-8744 or emailing us at [email protected]. Thank you and have a great day.
Question:	Do I need special protective gear to use this
Answer:	Mold, whether in a colony or individual spore has the same cellular structure. This product is disruptive to that cellular structure. So once it is applied to mold, it cannot survive.
Question:	Can this be used in a commercial fogger
Answer:	Yes, this product cleans mold on all soft surfaces without damaging the fabrics or leather. However, it is not a bleach and will not remove dark stains.
Question:	Does it just kill mold, or does it also kill mold spores
Answer:	Add 4 oz. to a quart bottle, then fill with water. A 16 oz. bottle will make 4 quarts. We have found it to be more cost effective this way and we use a lot of it!
Question:	I have mold on the leather inside my car, is this the correct product for removal and prevention
Answer:	If you want to treat your pots, pans, and dinnerware, you can fill her sink up with water and add one ounce of EC3 Mold Solution Concentrate and just dip them into the solution and allow them to air dry. Once Dry rinse them off with water and allow them to dry.
Question:	how much of this concentrated cleaner do you add to spray bottle? Trying to decide if this is more cost effective than the bottle of spray
Answer:	I had a real stubborn block in my kitchen sink and I used two bottles of this product with no result. I then bought SCOTCH CORPORATION 1969 Hair & Grease Drain Opener A Non-Acid Formulation, 1 L, let it sit over night and my drain is flowing like brand new. Hope this helps. You can but this product on Amazon.
Question:	As apposed to wiping my kitchen ware like dishes and pans individually with Ec3, Can I soak a few of them together in a solution of this somehow
Answer:	It says it’s safe for all pipes and septic systems, if you have a problem and it destroys your pipes or toilet, chances are your pipes were close to being bad anyways but I would still contact the company and make them pay for damages assuming you can prove with a plumbing inspection that this caused your problem

Product features

DIRECTIONS FOR BEST RESULTS

EC3 Mold Solution Concentrate comes in a 16 oz. bottle and makes one gallon of the total solution and can be used after diluting per bottle instructions for use in a spray bottle, mister, or fogger to treat larger areas.

EC3 Mold Solution Concentrate works on contact. This product will darken over time, but this will not impact efficacy.

Ingredients: Distilled water, a proprietary blend of Citrus Seed Extracts, and Vegetable Glycerin.

BOTANICALLY BASED

Spraying, misting or fogging with EC3 Mold Solution Concentrate are ways to clean and deodorize the air and all surfaces (hard and soft surfaces like countertops, furniture, floors, drapes, and carpets).

PROPRIETARY BLEND

This proprietary blend of citrus seed extracts is designed for effective cleaning without introducing harmful chemicals into your home.

EASY TO USE

Dilute in a spray bottle, mister or fogger. Spray or mist on floors, walls, ceilings, clothes, shoes, etc. and let air dry, wipe, or vacuum.