10 best inateck powered usb hubs

• PCIe USB 3.0 Card: SuperSpeed USB 3. 0 supports transfer rates of up to 5Gbps - The actual transmission speed is limited by the setting of the device connected
• One Step Update your Computer to 5 ports USB3. 0 Easily with PCI Express to USB3. 0 Controller Adapter Card; 1 USB 3. 0 20-pin Connector ( expand another two USB 3. 0 ports )
• Backwards compatible with USB 2. 0 and 1. 1 devices; Operating System Compatibility: Windows XP/Vista/7/8/10,Mac OS 10. 8 or above.
• With easy installation, this USB 3. 0 PCI express I/O Card offers a simple solution for your standard desktop PC
• Windows XP and Vista Users Please Note: Due to OS limitations, the real transfer speed after installation of the respective drivers will be located between the level of USB 2. 0 and 3. 0

User questions & answers

Question:	What is the practical difference between the "5 Ports Rear & 20PIN Internal" versus the "5 Ports Rear & 2-Port Internal
Answer:	The 5-Port, 20-Pin has a USB 3.0 header internally so that you can connect cables (that probable came with your case) to external USB ports. Frequently, these are on the front or the top of your case. The 2-Port internal actually has two standard USB connections so that you can connect standard USB cables within the case. There may be instances where a case's external USB ports need that but I think most need the 20-Pin header.
Question:	Does this card work on linux distros? if it's worked for you, which distro and kernel
Answer:	The card works at USB 2.0 speeds on Linux. It does not work at USB 3.0 speeds on my computer. The manual says: "USB 3.0 Drivers are not supported on Mac or Linux OS." I am using it on a HP Z800 workstation running Linux Mint Cinnamon 19.1. It took over 6 hours to transmit 1 TB of data from an external drive that has USB 3.0. The data speed started out at 75 Mb/sec then quickly slowed to 54 to 55 Mb/sec.
Question:	how many controllers does this have
Answer:	It has one 4 channel Frisco Logic controller and one Via VL8120Q7 hub controller for sharing those ports. It is not completely clear which of the 7 possible ports are shared.
Question:	Has anyone used this with Windows
Answer:	On 11 June 2016 I installed KTU3FR-5O2I the 5-port USB 3.0 interface board into an Acer Aspire AT3-710-UR57 Desktop. The purpose was to connect multiple Seagate USB 3.0 hard drives to it. The hardware installation was straight-forward. My system required the Molex-to-ESATA power adapter (which was one of the two cables sent with the board). I made sure the loose end of that cable was tied down with a Tie Wrap so that it wouldn't possibly intrude into the CPU cooling fan (which on my system was a bit close to it). When it booted up there were no software problems/issues. I went to the Inateck Web site, downloaded the right device driver (get the newest version for the board, the driver is described as the device driver for Windows 7 "Driver For Windows Ver3.5.106.0"), double-clicked on it to extract the zipped files into "My Documents" and ran the set up program. After that completed, I rebooted and all hard drive functions worked A-OK. No software problems/issues with Windows 10 Professional 64-bit and the KTU3FR-5O2I. I used the Inateck device driver because I wanted to ensure any KTU3FR-5O2I-specific functionality was included, but as noted in several comments Window 10 includes native support for the KTU3FR-5O2I chipset so I would agree the KTU3FR-5O2I should work in Windows 10 systems without installing the Inateck driver, but also in my case at least, it worked perfectly in Windows 10 Professional 64-bit when using their driver. Apparently their driver installation program did make changes because Windows 10 advised a reboot is required, but it's also possible no actual changes were made because the latest chipset is already supported. Regardless, the KTU3FR-5O2I worked A-OK in Windows 10 Professional 64-bit.

Product features

Operating System Compatibility:

Compatible with Windows XP/ Vista/ 7/ 8/ 10. Windows 10 and Mac 10.8.2 and more latest systems are built with a driver inherently. Windows systems earlier than Windows 10 and Mac OS earlier than Mac 10.8.2 require installing a driver in CD

Cable Connected Attention:

Please make sure the power cable strand colours match each other when connecting to the power augmentation, as to avoid faulty currents.

Package List:

1x USB3.0 PCI-E expansion card, 1x CD Driver, 1x mounting screw, 1x User Manual, 1x 4pin to 2x15pin cable (If no 15pin SATA power connector in your PC, please use the 4pin Molex to SATA converter）, 1x 15pin to 2x 15pin SATA Y-cable

Step 1:

Shut down the PC and unplug the power supply. Then open the PC case to find the corresponding PCI-E interface on the motherboard.

Step 2:

Plug in the expansion card and tighten the screws.

Step 3:

Connect the power supply cable in the correct direction.

Step 4:

Close the PC case cover.

Step 5:

If the computer does not pop up the driver automatically, please install the driver from the CD included in the package.

Friendly Service :

We provide friendly after service.

• SuperSpeed USB 3.0 supports transfer rates of up to 5Gbps - The actual transmission speed is limited by the setting of the device connected
• 4 USB 3.0 downstream ports for standard desktop PCs; Supports USB Hot Plug, Plug & Play; Support LPM, Low Energy Consumption; 15 pin SATA Power Connector to power USB devices from your PC power supply
• Backwards compatible with USB 2.0 and 1.1 devices; Operating System Compatibility: Windows XP/Vista/7/8
• With quick and easy installation. All USB 3.0 PCI-E Cards require an external connection to the power supply of the PC in order to supply voltage to the USB buss

User questions & answers

Question:	Is it better to use the mini PCIe slot or the larger one
Answer:	If you mean the short versus the longer slots (X1 or X 16) it doesn't matter.It is only going to draw the power that it needs because the connectors are only going to connect in a X1 (short slot) mode. The main issue is that you connect the card to an internal power supply, either the Molex connector or the SATA style connector; whichever one will fit. My suggestion is to install it in one of the X1 (short) slots and save the longer slots for something like a video card. Windows 7 will find drivers for it but it's a good idea to use the driver disk that came with it. You're not going to get super blazing speed unless you have some super blazing adapter or protocol installed which most USB 3.0 devices do not have. However, I have been very happy with this device even though I know I'm not going to get the full throughput that is commonly advertised for USB 3.0. You have to read the advertisements carefully because they say UP TO 400+ megabits per second.
Question:	If I plug in four 3.0 usb flash drives into this, will all four of the usb ports operate at 3.0 usb speed
Answer:	This card, like most, has one Host Controller (the main chip on the board). This single controller has a 5Gbps max, and all four ports share it. You can do a search for 'dedicated channel' cards and find ones built with multiple chips-- but they are expensive!
Question:	Whats the chip set
Answer:	Fresco FL1100
Question:	How to install the PCI-E card
Answer:	1. Turn off the power to your computer.2. Unplug the power cord and remove your computers cover/side panel.3. Remove the slot bracket from an available PCIe slot.4. To install the card, carefully align the card's bus connector (golden portion) with the selected PCIe slot on the motherboard. Push the card down firmly.5. Use the included screw (or the screw from the slot bracket) to secure the card to the case.6. Replace the computer cover/side panel and reconnect the power cord. Then install the driver. (No additional driver is needed for Mac Pro/ Win8)Here is a video about how to install PCI-E card on Inateck officail website：http://www.inateck.com/inateck-ktu3fr-5o2u-usb-3-0-pci-express-card/

Product features

5 Gbps in total:

5 Gbps is shared by 4 downstream ports. This speed can be reached while only one downstream port is in use.

UASP supported:

It excellently show you the speed of USB 3.0 5 Gbps.

Hot swap supported:

The 4 downstream ports support hot swap function, plug and play.

Installation and Driver:

Please visit the official site of inateck, where installation video and free driver are available.

• PCI-E to USB3.1: Expand your computer with two more ports, one USB-A and one USB-C. USB-A is downwards compatible with USB3.0/USB2.0. USB-C port brings convenience to your Type-C devices.
• USB3.1 Gen 2: The PCI-E card is equipped with 10Gbps bandwidth, which ensures fast data transmission, real speed of USB3.1 for individual port.
• Good Compatibility: Compatible with Windows 7/8/8.1/10/Linux Kernel,Mac OS 10. 8 or above and more operating system. Comes with extra drive disk. Supports motherboard equipped with PCI-E x4 slot and versions above.
• Stable Power Supply: Equipped with power management chip, plus 15-Pin SATA power cable.
• User Friendly: Both USB-A and USB-C ports on the PCI-E card support hot swap, as well as plug and play.

User questions & answers

Question:	I have a usb-c hub with 2 hdmi monitors, keyboard and mouse. Will this usb-c connected to the hub enable my computer to see these devices
Answer:	No, you will need to use a USB on the motherboard.
Question:	will this work on a hackintosh high sierra coffee lake without installing kexts (plug and play
Answer:	Technically, the card could only fit standard ATX computer case. If your device meets the condition, the card would work for you.
Question:	Inateck pci-e to usb 3.1 pci express card kt2001, does this card working perfectly with the oculus rift s
Answer:	Works fine with my Rift S. Needed Inateck’s driver (downloaded from Inateck support page, will not work with the Win 10 native) and an internal power cable.
Question:	Can I install this card in a first generation pci-e 4x slot? How fast would it be
Answer:	This card is designed for PCI-E slot with PCI-E agreement 2.0 and above. If you install it in a first generation PCI-E 4x slot, I'm afraid that the speed will be very slow. Perhaps, it will be below 250MB/S.

• No additional power supply for normal recognition and operation needed anymore; one step update your Windows computer to USB3. 0 Easily with PCI Express to USB3. 0 controller adapter card; Supports USB hot Plug, plug & play; low energy consumption
• Operating System compatibility: Windows XP, 7, 8 (32/64-bit), 10; backwards compatible with USB 2. 0 and 1. 1 devices; Super speed USB 3. 0 supports transfer rates of up to 5 Gaps, The actual transmission speed is limited by The setting of the device connected
• With quick and Easy installation, enjoy Copying videos, music, photos, data files between USB devices and the computer at blazing fast speeds
• Windows XP and Vista users Please note: due to OS limitations, The real transfer speed after installation of the respective drivers will be located between the level of USB 2. 0 and 3. 0
• Package: 1x USB3. 0 PCI-E expansion card; 1x CD driver; 1x User's manual

User questions & answers

Question:	Does this card work with Windows Vista Home Premium (64)? No mention in the description
Answer:	On Youtube search for "installing pcie usb 3.0 card' and see if it looks like you want to try it. This is what I remember doing, but all situations are different: power down computer, disconnect power cable, then open case, find empty PCI-E slot, and remove its cover at back of computer case. Then insert PCI-E card firmly into slot, secure with screw if necessary. Disconnect power cable from hard drive, insert proper Y cable to card, hard drive and power supply. Close case, reconnect power cable, restart computer. If you have Windows 10, it will install drivers, if not, should be on supplied CD. My interface has been fine so far.
Question:	How do I get an adapter to connect this card to the front USB ports on the computer
Answer:	No, This is only used for usb type a and one usb type c expansion. What you would be looking for to run video would be a thunderbolt expansion card, Thunderbolt and type c look the same but are not. Only the Thunderbolt card will support video output.
Question:	How come This does not have a power connector ? All usb 3 needs power
Answer:	I believe the 20 pin adapter is used for a computer which has a 20-pin connector on the motherboard for direct connection for usb 3.0. Most older computers will use the molex 4 pin male to 15 pin sata connector. My older computer did not have the usb 3.0 20 pin connector on the motherboard. If you search "UCEC USB 3.0 Motherboard 20 Pin Male to Female Extension Cable 50cm" in amazon you will see what it looks like.
Question:	I only have Pcie 1x slot. Which card will work with Pcie 1x, 2 Ports Rear & 20 Pin Internal or 4 port USB 3.0/ New Release version
Answer:	Today I tested mine and doesn’t work at all, and didn’t find any driver. I will do more research to see if I can get it to work! I will keep you posted!

• Plug and play, hot swappable, high speed USB 3.0 Specification and backward compatible with USB 2.0
• Support windows 2000/ XP/ 7/ 8/ 10/ Mac OSX 10.X or higher
• Connect to the SATA device using USB interface
• Support 2.5 inch and 3.5 inch SATA HDD/SSD, Blu-ray DVD, CD-ROM, DVD-ROM, CD-RW, DVD-RW, DVD+RW combo devices
• High-speed encryption and decryption processing provides throughput without impairing the speed performance of standard HDD

• 【External hard Drive Reader】: support 2.5/3.5 SATA HDD and SSD, 2.5 /3.5 IDE HDD, SATA DVD-ROM, CD-RW, DVD-RW, DVD+RW Optical Drive, dual-head IDE connector Plus one SATA II connector.
• 【Widely Compatibility】: This USB 3.0 to IDE and SATA adapter allow to operate 3 HDDs simultaneously, It is compatible with 2. 5"/3. 5" Ide/SATA hard drives and 5. 25" Sata CD/DVD drives.
• 【High speed transfer】: data transfer up to 5Gbps.Backward compatible with USB 2.0/1.1.
• 【Support system】: Windows XP/Vista/7/8/10(32bit and 64bit); Mac OS 10. X (OTB mode isn't applicable for W8 and Mac)
• 【Additional function】: plug and play; hot swap; on/off switch for HDD protection. Led light shows power and activity status.
• 【Packing content】: 1 x USB 3.0 to IDE/ SATA adapter, 1 x USB 3.0 cable - 1 x 4pin power cable - 1 x Power adapter - 1 x OTB Softwar CD, 1x User Manual

Product description

Expansion of USB 3.0 ports and charging

This atolla USB 3.0 hub can expand 1 USB 3.0 port to 7 external USB 3.0 data ports for more USB devices, sync data at blazing speeds up to 5Gbps in no time.



In addition, a USB 3.0 charging port can help charge your iPhone, iPad or any other USB 3.0 devices while connecting to the 5V/4A adapter.



Individual Switches

On and off switches with led indicators for each port are designed to turn on or off the individual USB port without unplugging the equipment, and blue LED lights show the working status easily.



With these individual switches you can save trouble of inserting and unplugging your devices and help place them more rationally when you don't use them.



Easy Setup

No driver required; support Plug & Play and Hot Swap



18-Month Warranty

We provide an 18-month warranty and friendly, easy-to-reach support, including replacement and refund.

Because we believe a good product is inseparable from our customer's support and feedback.



Supported Systems

Windows: 10, 8.1, 8, 7, Vista, XP

Mac: OS, X, 10.x(and above)

Linux



Notes

1.In order to achieve the fastest transfer speed 5 Gbps, we suggest connect to USB 3.0 version devices, including USB 3.0 ports, USB 3.0 cables and more.

2.For a stable connection, the devices connected to this USB 3.0 Hub with power adapter must not exceed a combined current of 4A.

• 【Instant expansion and SuperSpeed Syncing】-This 7-port USB 3.0 data hub can instantly expand 1 USB 3.0 port to 7 external USB 3.0 data ports for keyboard, mouse, printer, hard drivers and more USB devices, syncing data at blazing speeds up to 5Gbps in no time.
• 【Smart Charging Port】- Besides 7 SuperSpeed USB 3.0 ports, this USB 3.0 splitter offers a charging dedicated port, which is able to charge your iPhone, iPad faster and safer. With the 5V/4A power adapter, it can provide charging power up to 2.4A .
• 【Simple Switch to Control】- Equipped with individual on-off switches to control each USB port, atolla USB 3.0 hub saves the trouble of unplugging devices and help place them more rationally when you don't use them.
• 【Maximum Compatibility and Performance】- Compatible with Windows 10, 8.1, 8, 7, Vista, XP, Mac OS X (10.x or above), Linux. Fully plug and play, no drivers required and supports hot swapping
• 【In the Box】- atolla 7-port USB 3.0 hub (100cm of the USB hub cord), 5V/4A Power Adapter(120cm of the electrical cord), Quick Setup Guide. Guaranteed by bauihr 18-Month Warranty

User questions & answers

Question:	Why is my Daughter complaining that her phone stops charging overnight
Answer:	This is an external powered USB hub with individual port power control. If you're hooked up to a computer and you power off the system at night then the USB hub is not getting an "on" signal. This is not a wall plug phone charger, it requires an input source to be active, not just external power.
Question:	Does it work if the power adapter is not plugged into the wall
Answer:	I just tested mine and it works without the AC adapter connected. I'm not sure it would handle powering 7 devices along with the charging port though.
Question:	Can it be used only with the pc usb? or always need to be connected to the electrical outlet
Answer:	It depends on what type of USB port your laptop has (this dictates the maximum power transmission capacity) and how much demand you're placing on the device. If it's a bunch of small things like BT dongles and small flash USB/SD drives, it may power them all. If you use an external HDD or SSD (some are built to be that from the start, the rest can be converted to one via a USB enclosure), especially the 3.5 inch varieties which standard desktop towers use, you are far more likely to have power shortages. For example, my SSD/HDDs will beep when attached to a hub and cannot be loaded by the PC, if I use two at a time and I don't attach some sort of external power source (or I don't use one high enough). Also, bear in mind each USB port in a hub has a maximum power transmission rate. Thus, if you use a device that consumes far less power than the listed combined max rate/power jack intake for the hub, but consumes more than what an individual port of that hub can provide, it will not work properly. This shouldn't be a concern unless you use a very high-power or high-end device. For reference, an external 2.5-inch USB external hard drive uses 0.5 amperes (also listed as 500 mAh). The standard 2.0 USB A-type ports supply at least 0.5 A.
Question:	Can all ports be used for charging and transfer data
Answer:	All upper ports can be used for data and charging. The port at the front of the hub is charging only. I run my USB desk light from the front port, and works fine. The 7 upper ports I use for things like my wireless keyboard/mouse, cell phone charging/connection to laptop. It runs my external DVD drive, and works with all ports in use at once. Works with USB 3/2 with no data loss. I will purchase a new one to replace an existing hub behind my desk. Lastly, I have gone through multiple devices like this one, and they fell apart, or failed within a year. This device has exceed my expectations.

Product features

Expansion of USB 3.0 Port and Charging

• 7 USB 3.0 data ports, support data transfer speed up to 5Gbps
• Backward compatible with USB 2.0
• The maximum output current of each USB 3.0 data port is 1.5A
• 1 smart USB charging port, can provide current up to 2.4A (maximum output of any USB 3.0 charging port)for charging your mobile phone, camera, and any more USB devices.
• Provide a 5V/4A power adapter that helps transfer data more stable.

Individual On/Off Switches

• Easily to turn on or off the individual USB port without unplugging the equipment
• Saving trouble and protecting each USB port from frequently inserting and unplugging your devices
• Blue LED lights show the working status, the light would go 'off' when the port is 'off'
• Help place your USB devices rationally when you don't use them
• Turn on: tap the button
• Turn off: press and hold for 2s

Best Adapter, Long Cable

1. USB 3.0 hub cable length: 100cm
2. 5V/4A power adapter ：

• Electrical cable length: 120cm
• Input: 100-240 V AC 50/60 Hz
• Output: 5V, 4.0A (4000 mA)
• Plug Spec: ID: 1.35mm; OD: 3.5 mm; Length: 10 mm
• Certifications: FCC, UL

18-month after-sale service

We provide an 18-month after-sale service and friendly, easy-to-reach support, including replacement and refund.

Easy to carry and setup

• Length : 16cm
• Width : 4.5cm
• Height : 2.3cm
• No driver required
• Support Plug & Play and Hot Swap
• compact and easy to carry out

Widely compatibility

• Windows: 10, 8.1, 8, 7, Vista, XP
• Mac: OS, X, 10.x(and above)
• Linux

Product description

10-Port USB Hub

The Massive High-Speed Charging Data Hub



From ANKER, the Choice of 50 Million+ Happy Users

• Industry-Leading Technology

• 18-Month Warranty

• 99% Positive Feedback



Quick Sync

Transmit data via USB at up to 5Gbps, fast enough to transfer a high-definition movie in seconds—no more wait times when sending and receiving important files.



Charge Faster

3 PowerIQ ports detect your device's charging protocols to deliver the optimum charge at speeds up to 2.1 amps per port or 10 amps overall.



Compact Power

Only about the size of a pen case, this compact yet powerful data and charging hub won't clutter your workspace. A 12V / 5A AC power adapter ensures ports are fully operational at all times.



18-Month Warranty

At Anker, we believe in our products. That's why we back them all with an 18-month warranty and provide friendly, easy-to-reach support.



Supported Systems:

Windows 10, 8, 7, Vista, XP

Max OSx 10.6-10.12 or later

Linux 2.6.14 or Later



Compatibility:

2.4 GHz wireless devices, MIDI devices and some USB 3.0 devices may not be supported. Try using the host port or a USB 2.0 connection.

The non-charging ports are intended for data transfer only. They provide insufficient power output for charging.

Ensure that the adapter is connected before using this hub.

Use official or certified third-party cables only. Do not use cables that have frayed, broken, or have exposed wiring. Data Port Output Current:5Gbps|Charging Port Output Current:2.1A

• The Anker Advantage: Join the 50 million+ powered by our leading technology.
• Ultra Fast: 7 ports offer high-speed data transfer of up to 5Gbps. Get synced up in no time.
• Advanced Charging Technology: 3 ports equipped with Anker-exclusive PowerIQ deliver the fastest possible charge of up to 2.1 amps per port.
• Compact Power: 60W packed into a device the size of a pen case. Simultaneously charge multiple devices while conserving space.
• What You Get: Anker 60W 10-Port USB 3.0 Data Hub, 12V / 5A AC power adapter, 2.6ft. USB 3.0 cable, welcome guide, our worry-free 18-month warranty and friendly customer service.

User questions & answers

Question:	I want a hub to give 5v to my blue yeti mic., as well as to power a wd 3tb portable drive. i need powered and data ports. 3.0 is future proofing
Answer:	The IQ ports just provide power. They don't provide a data connection. So you'd need a data connection that delivered 1.3 amps. Some drives provide a "Y" cable that allows you to connection to two ports. One of them is the data connection, the other is providing just additional power. The data ports on this provide .9 amps each so you could use two of those or figure out which connection on the "Y" cable is data and which is just power and connect the one that is just power up to the IQ port. If you just have one USB connection on your cable you might need to find another hub that provides 1.3 Amps (i.e. 1300 mA) or more.
Question:	Some of the usb ports (data sync) have stopped working.Is this a common issue
Answer:	The light on my HyperX Cloud 2 stays on. And my Laptop Cooling Pad (fan) stays running. So I would say the power stays on.
Question:	Will this hub work with a usb 2.0 bdr drive operating at 1.3 amps? can it be plugged in iq ports
Answer:	This PowerPort Strip 3 supports 100-240V, it can be used in Europe.
Question:	Does the hub stay powered after the computer is off? ie if i turn off my laptop will my keyboard lights turn off as well if i'm using external power
Answer:	It's 300J.

Product features

10-Port 60W USB 3.0 Hub

Boasting 7 USB 3.0 Ports and 3 PowerIQ Ports, the 10-Port 60W USB 3.0 Hub is built for serious duty. 3 PowerIQ ports detect your device to deliver one of its fastest possible charge (up to 2.1A per port), while the remaining 7 ports seamlessly handle all your data transfer needs.

PowerIQ Technology

By intelligently identifying any connected device, PowerIQ delivers the optimum, high-speed charge to all devices. Includes Apple and Android phones and tablets as well as cameras, consoles and more.

Ultra Fast

With data transfer rates of up to 5Gbps, get synced up and on your way faster than ever. 3 PowerIQ ports detect your device to deliver its fastest possible charge speed - up to 2.1 amps per port.

Safety First

Guaranteed Reliability: Our products are made with superior materials and technology to enhance both performance and safety. Built-in surge protection provides additional defence for the Hub, and your devices.

Product description

Add up to 4 devices quickly and easily with the Sabrent 4-Port USB 3.0 Hub. The thin, lightweight design makes this hub a great travel companion to expand one USB 3.0 port into four. Especially great for notebooks which come with only a few ports in an era when you need to attach many USB devices at once, such as a printer, card reader, cell phone, iPod, thumb drive, mouse, keyboard, or an external hard drive. Fully backwards compatible with the USB 2.0/1.1 products. Plus, each port has its own separate power switch so you can control each port independently.





Expand your high speed USB 3.0 ports

Technology seems to advance at ever increasing speeds. With the recent release of Super-Speed USB 3.0, you can now transfer data at up to 10 times the speeds of the older USB 2.0 standards! Speeds of 5Gbps are a vast improvement over USB 2.0 that only supports up to 480Mbps. The Sabrent USB 3.0 Hub is a great tool to expand a single USB 3.0 port into 4 ports, so now you can connect all of your USB devices at one time. Plus, its small and elegant design has been configured to be as thin as possible so as to not take up precious space as you travel. Yet, it is still backward compatible with your older devices, so you can still use it in conjunction with USB 2.0 devices.



System Requirements:



* Windows 2000/XP/Vista/7/8/8.1/10

* Mac OS X



Please Note:

2.4Ghz wireless devices, such as wireless keyboard and mouse adapters, may not work in close proximity to USB 3.0 devices or hubs. Connecting to a USB 2.0 port is recommended.



For a stable connection, the devices connected to the 4-Port USB 3.0 Hub must not exceed a combined current of 5 volts 900 mAh.

This 4-Port USB 3.0 Hub will not charge an iPad (it will only sync).





Package contents

Sabrent 4-Port USB 3.0

5V/2.5A power adapter

• Instantly Add Four USB 3.0 Ports to Any Compatible Device
• Individual Power Switches with LED Indicators
• Supports Transfer Speeds up to  5Gbps (USB 3.0), 480Mbps (USB 2.0), 12Mbps (USB 1.1)
• 2.5 Amp Power Adapter Included to Power up Your Devices
• Easy Setup: Plug & Play, Hot Swappable

User questions & answers

Question:	Can you use the power supply one, without the power supply if you wanted to
Answer:	Yes the USB hub will work fine without the AC power adapter. You will need the AC adapter if you want to charge more power-intensive accessories like iPads, etc. that require higher current or if you want to charge 4 devices at one time.
Question:	How long is USB3 cable
Answer:	measured mine at about 1 meter. I really like this thing. The two red high-power only ports are oriented 180 degrees from the USB 3.0 ports so you physically can't mix them up either.
Question:	How many ports can I have active at one time, without overloading the single port of the computer
Answer:	You can use all 4. However, If you need to utilize the speed of 3.0 x4 you will need that kind of throughput on the port you attach it to and this device as well (not sure of max throughput). Most USB devices don't need that kind of speed (such as web cam, keyboards, mice) For instance, if you hook up 3 external SSD drives and VR headset, you will potentially bottleneck on speed. The devices will still function, just not at 100% speed.
Question:	what's the different between the one with the external power adapter and the one without
Answer:	With my USB 3 Ports on my Acer TC-780 front panel ports, I can power all four ports with thumb drives. When I tried the same with a Dell U473D Slim Multimedia Keyboard with 2 USB Port I had to use the pawer supply that came with the HB-UMP3 4-port Powered USB hub. I would advise getting the powered hub because you don't know if your USB port will support enough devices without the power supply unit.

Product features

Product Description

Quickly add up to four devices with the Sabrent 4-Port USB 3.0 Hub. The thin, lightweight design makes this hub a great travel companion. Especially great for notebooks that come with a limited number of ports. Add multiple peripherals such as a printer, card reader, cell phone, iPod, thumb drive, mouse, keyboard, or an external hard drive. Fully backward compatible with the USB 2.0/1.1 products. Every port has its own power switch, allowing you to control each port independently.

Please Note: 2.4Ghz wireless devices, such as wireless keyboard and mouse adapters, may not work near USB 3.0 devices or hubs. Connecting to a USB 2.0 port is recommended.

For a stable connection, the devices connected to the 4-Port USB 3.0 Hub must not exceed a combined current of 5 volts 900 mAh.

This 4-Port USB 3.0 Hub does not charge your devices (it can only sync).

Individual Power Buttons

Add 4 Devices with the Sabrent 4-Port USB 3.0 Hub.

Seamless Data Transferring

Supports USB 3.0 transfer rates up to 5Gbps. Backward compatible with all USB 2.0/1.1 devices and hosts.

Power Adapter

2.5 Amp Power adapter included to power up high powered devices.

Compatible With Most Operating Systems

Compatible with: - Windows2000/XP/Vista/7/8/8.1/10.

- Mac OS 9.1 & Higher.

- Linux 2.4 or Above.

Product description

THE PERFECT USB 3.0 HUB YOU EVER NEED！

SuperSpeed Sync and Dynamic FastCharging: Extend 4 more USB 3.0 Ports + 1 Smart Charger Port (up to 2.4 Amps).

Unplugging-Free: Individual on/off switch turns off port whenever you don’t need it.

Vertical USB Port provides additional space for “fat” USB devices and plugs.

Nice Design, Solid Built with a strong cable of 26″ length. Provide one 5V DC port for an additional power adapter.



Superspeed - 4 USB 3.0 Data Ports

Expand USB connectivity to 4 external USB 3.0 ports, with SuperSpeed transfer rates up to 5Gbps (10x USB 2.0)

Backward compatible with all USB 2.0/1.1 devices and hosts



Smart Charging Port (Up to 2.4A)

Additional Charging Port recognizes and optimizes the charging power of your electronic devices for fast and efficient charging. With AC power adapter applied, it provides up to 2.4Amps, ideal for iPads, iPhones, and other devices.



5V/3A Power Adapter

Allows you to use more devices to make the hub output faster and more consistently.

It is recommended that USB hub be connected to a power adapter for use.



UNPLUGGING-FREE, SIMPLE SWITCH TO CONTROL

Equipped with four illuminated individual on-off switches to control each USB port, atolla USB 3.0 splitter hub saves the trouble of unplugging devices whenever you don’t need it.

Turn on: tap the button

Turn off: press and hold for 2s



Compatible System

Microsoft Windows 10 (32 / 64bit), Windows 8.1 (32 / 64bit), Windows 8 (32 / 64bit), Microsoft Windows 7 (32 / 64bit), Windows Vista (32 / 64bit), Windows XP (32 / 64bit), Windows 2000, Linux, MacOS 10.x, Linux.



Product Information

Hub dimensions: approx. 108x43x23mm

Length of connecting cable: approx. 630mm

Weight: approx. 194g (6.84oz)

Material: ABS with piano lacquer

Cable length: 60cm

• 【SuperSpeed Syncing and Smart Charging】- atolla USB 3.0 hub can expand 1 USB 3.0 port to 4 extra USB 3.0 data ports for hard drives, flash drives among other USB devices, syncing data at blazing speeds up to 5Gbps. A charging port can provide up to 2.4Amps to charge your iPad, iPhone, etc.
• 【Simple Switch to Control】- Equipped with four illuminated individual on-off switches to control each USB port, atolla USB splitter hub saves the trouble of unplugging devices whenever you don't need it
• 【Elegant Design and Sturdy Case】- Solidly built, atolla USB hub features a compact case with sleek glossy UV finish and a 60 cm (23.62") strong thick cord
• 【Maximum Compatibility and Performance】- This 4-port multi extension port USB hub compatibles with Windows 10, 8.1, 8, 7, Vista, XP, Mac OS X (10.x or above), Linux. Fully plug and play, no drivers required and supports hot swapping
• 【In the Box】- atolla USB 3.0 Hub, 5V/3A AC Power Adapter, Quick Setup Guide. Guaranteed by atolla 18-Month Warranty

User questions & answers

Question:	Will this work on my older laptop that may not have a usb 3 port. i want to connect my printer scanner and a usb stick drive at the same time
Answer:	Hi， The USB 3.0 data port on the hub is backward compatible with USB 2.0 devices. So it can be supported.
Question:	What are the input specs of the power adapter? Does it handle 110-240V
Answer:	The label on the adapter says input is 100v-240v 50/60 Hz.
Question:	if connected to my pc, can i use it to run all 4 ports at once? i.e joystick, mouse, headset, pedals
Answer:	Hi， It is recommended to connect the power adapter to provide sufficient power for multiple devices.
Question:	Are the data ports powered from the usb or the power supply? the amp draw of what i need to plug in is too great for my computer's usb port
Answer:	Powered from the power supply. That is why I needed to get this.

Product features

THE PERFECT USB 3.0 HUB YOU EVER NEED！

• SuperSpeed Sync and Dynamic FastCharging: Extend 4 more USB 3.0 Ports + 1 Smart Charger Port (up to 2.4 Amps).
• Unplugging-Free: Individual on/off switch turns off port whenever you don’t need it.
• Vertical USB Port provides additional space for “fat” USB devices and plugs.
• Nice Design, Solid Built with a strong cable of 26″ length. Provide one 5V DC port for an additional power adapter.

Superspeed - 4 USB 3.0 Data Ports

• Expand USB connectivity to 4 external USB 3.0 ports, with SuperSpeed transfer rates up to 5Gbps (10x USB 2.0)
• Backward compatible with all USB 2.0/1.1 devices and hosts

Smart Charging Port (Up to 2.4A)

• Additional Charging Port recognizes and optimizes the charging power of your electronic devices for fast and efficient charging
• With AC power adapter applied, it provides up to 2.4Amps, ideal for iPads, iPhones, and other devices

5V/3A Power Adapter

• The 5V/3A power adapter allows you to use more devices to make the hub output faster and more consistently
• It is recommended that USB hub be connected to a power adapter for use

UNPLUGGING-FREE, SIMPLE SWITCH TO CONTROL

• Equipped with four illuminated individual on-off switches to control each USB port, atolla USB 3.0 splitter hub saves the trouble of unplugging devices whenever you don’t need it.
• Turn on: tap the button
• Turn off: press and hold for 2s

Compatible System

Microsoft Windows 10 (32 / 64bit), Windows 8.1 (32 / 64bit), Windows 8 (32 / 64bit), Microsoft Windows 7 (32 / 64bit), Windows Vista (32 / 64bit), Windows XP (32 / 64bit), Windows 2000, Linux, MacOS 10.x, Linux.

Product Information

Hub dimensions: approx. 108x43x23mm

Weight: approx. 194g (6.84oz)

Material: ABS with piano lacquer

Cable length: 60cm

Power Adapter: 5V / 3A

Cable length of power adapter: approx. 120cm