10 best orion car amplifiers

Product description

ORION Cobalt 4 Channel Amplifier 2500 Watts for Car Audio Speakers Subwoofers

• Features – The 4 channel bass boost amplifier has features like - Frequency Response: 10HZ-30KHZ, Remote Bass Knob, 2-way protection, hi/low pass crossovers, hi/low level inputs, MOSFET Power Supply, Thermal Protection, Gain Control, 2 Ohm Stable
• Class A/B – This multichannel subwoofer amplifier exhibits a Class A/B topology. In the presence of no audio signal, Class A Amplifier has a high amount of current flowing in its output while Class b amplifier has no current flowing.
• Quality - This Class A/B 4 channel amplifier exhibits quality frequency response rates and crossover network which places this amp at a prominent place. Durable design and highly efficient performance makes this subwoofer amp for car speakers stand out amongst the others.
• Power – This Class A/B 2500 watt Amplifier has a power rating distribution as followed 625 X 4 MAX @ 2 OHMS. The 4 channel amplifier for car speakers also provides a 2-way protection circuitry as a part of its design.
• Low/High Level Inputs – The multichannel amplifier for car speakers come with low/high level inputs. A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers

Product description

ORION COBALT CBT-4500.1D, CLASS D AMPLIFIER 4500 WATTS MAX MUSIC POWER 1 OHM

• By Orion High Performance Car Audio
• CLASS D AMPLIFIER 4000 WATTS MAX MUSIC POWER 1 OHM

User questions & answers

Question:	What is the Rms watts running @ 2 ohms
Answer:	Maybe 600
Question:	Will this amplifier run at 2 ohms
Answer:	Yes can run at 1 ohm and 2 ohm but won’t get all the power out of the amp at 2 ohms,
Question:	What is the Rms watts at 2 ohms
Answer:	Maybe 600 watts

• RMS Watts @ 4 Ohm Stereo 12.6V:   1050 Watts X 1 Channel / RMS Watts @ 2 Ohm Stereo 12.6V: 1600 Watts X 1 Channel / RMS Watts @ 1 Ohm Stereo 12.6V: 2500 Watts X 1 Channel
• Nominal power output 1ohm(watts): 5000 Watts, Max music power: 10000 Watts
• Frequency Response   20Hz~250KHz
• Signal Noise Ratio: 65dB
• Hi Pass Freq. 30Hz-250Hz / Low Pass Freq.

User questions & answers

Question:	Is this a good amp to push 2 p3 15’s wired at 4 ohms
Answer:	I would wire them to 2 ohm each then bridge them for a 1 ohm load... that will slap hard...
Question:	This Mp can push two rockville destroyer 12d
Answer:	May need to get the Xtreme 4K for the destroyers
Question:	What if birth sheet comes in under rated
Answer:	My birthsheet for my xtr 2500.1dz was rated [email protected] volts at 1ohm... plenty power just make sure you have good electrical in your vehicle
Question:	What's the maximum current draw for this amplifier
Answer:	It has a maximum current draw of 250 amps
Question:	anyonw knows what the 3 fuses on this are for
Answer:	They will pop before it blows your amp. Just like a breaker in your house.
Question:	would this amp be enough to push 2 rockford p3 dual 4ohm wire to 1ohm
Answer:	The amp is 1 ohm stable. I own the exact one. And it is great. The lowest resistance u are gonna get outta the subs is gonna be around 2 ohm being that they are 4ohm docs and not 2ohm dvcs
Question:	Will this push a 12” cobalt
Answer:	Yes it will push two 12", but you have to bridge it.
Question:	Would this run 2 mtx 10” 400 watt rms 4ohm subs if im not constantly at full power
Answer:	It should be fine I have a kicker comp r 800w rms it pushes it till I cracks and still has a lot of power left

• RMS Watts @ 4 Ohm Stereo 12. 6V:   600 Watts X 1 Channel / RMS Watts @ 2 Ohm Stereo 12. 6V: 975 Watts X 1 Channel / RMS Watts @ 1 Ohm Stereo 12. 6V: 1500 Watts X 1 Channel
• RMS Power Watts:       6000 Watts
• Frequency Response   20Hz~300KHz
• Signal Noise Ratio:       90dB
• Hi Pass Freq.    30Hz-250Hz / Low Pass Freq. 30Hz-250Hz

User questions & answers

Question:	Will this amp power 3 12 orion
Answer:	Asus Rampage III Gene motherboard based on Intel 1st generation Core i7 processors and X58 chipset supported low density DDR3 memory up to 24GB in 6 slots. It does not work with high density DDR3 HyperX FURY memory. Please upgrade Rampage III Gene with Kingston ValueRAM low density DDR3 1333MHz 4GB DIMM, part number KVR1333D3N9/4G. Install two (2) 4GB modules for a total of 8GB upgrade. Unfortunately low density HyperX products compatible with the board are out of production. Thank you.
Question:	I see one review mentioned overheating, has anyone else experienced any overheating issues
Answer:	You should be okay, I have been using them for awhile. these memories are volatile(ram), so doesn't affect when overclocking for gaming. What affects overclocking is a low speed CPU and of course you have to have some memory but the one compatible with your motherboard.
Question:	Enough for 2 Kicker 12” L7’s at 1 ohm
Answer:	The one can be cheaper than the two. I bought the one so later on down the road I could purchase another one.
Question:	How many channels
Answer:	Hello Tuhin,Although we have not tested this configuration it looks as if it should work based on your PC specifications. Keep in mind your system may default to the maximum of memory speed of 1600Mhz as you may need to adjust the speeds in your BIOS. You can also check out the following: KVR16E11/8HB. or further questions feel free to contact us at the following number: 800-435-0640 M-F 6AM-6PM PST Reference case: SR287781.Thank you for considering Hyper-X,Felinni M. @ Kingston Technology
Question:	when you turn up your volume does the amp distort your speakers
Answer:	Hello SUNIL, HyperX Impact HX424S14IBK2/32 meets MSI GS73VR 6VR Stealth system specifications and works well with the laptop. GS73VR clocks the Impact modules to system supported memory speed. Install the Impact kit to reach maximum 32GB RAM. Thank you!-Kai @ HyperX TS
Question:	How much true rms watts does this amp push out if i put 4 mids on it
Answer:	Hi Carlos, HyperX Impact DDR4 32GB laptop memory kit, HX424S14IBK2/32, meets Asus ROG GL502VS system specifications and works in the laptop just fine. Install the Impact kit to reach system maximum 32GB RAM. Thank you.
Question:	Do it have out put on it
Answer:	I just fnished answering a similar question on the GL502VS and during that research, I found this product continually pooping up as being compatible.This will work fine and run at 2400MHz,The total you can put in is 64GB
Question:	what are the dimemsion of this unit orion has some rare information
Answer:	This RAM is compatible with new iMac 2017, but it is not compatible well with Apple original RAM, if you want to upgrade RAM to 40GB by add 2 x 16GB RAM, it will make all RAM speed down to 2133MHz. If you intend to only use this RAM alone, not mix with Apple original RAM, you can buy this RAM and it is compatible with the new iMac 5K 2017. Also, my Apple original RAMs were in DIMM0 slots, system couldn't boot when I simply install Kingston RAMs to DIMM1 slots, so I swap Apple original RAMs to DIMM1 slots and Kingston RAMs to DIMM0 position, it now can boot successfully. Hope this answer helps.

Product description

Orion Cobalt 2 Channel Amplifier 750W RMS 1500W Max

• Features – The 2 channel bass boost amplifier has features like - Frequency Response: 10HZ-30KHZ, Bass Boost, Remote Bass Knob, Gain Control, 2-way protection, hi/low level inputs, Thermal Protection, MOSFET Power Supply, LED Power and Protection Indicator and 2 Ohm Stable
• Class A/B – This Orion Cobalt multichannel subwoofer amplifier exhibits a Class A/B topology. In the presence of no audio signal, Class A Amplifier has a high amount of current flowing in its output while Class b amplifier has no current flowing.
• Quality - This Class A/B 2 channel amplifier exhibits quality frequency response rates and crossover network which places this amp at a prominent place. Durable design and highly efficient performance makes this subwoofer amp for car speakers stand out amongst the others
• Power – This Class A/B 1500 Watt Amplifier has a power rating distribution as followed 750 X 2 MAX @ 2 OHMS, 375 X 2 MAX @ 4 OHMS. The multichannel amplifier for car speakers also provides a 2-way protection circuitry as a part of its design.
• Low/High Level Inputs – The multichannel subwoofer amplifier for car stereo speakers come with low/high level inputs. A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers

Product description

ORION COBALT CBT-3500.4, 4 CHANNEL AMPLIFIER 3500 WATTS MAX MUSIC POWER

• By Orion High Performance Car Audio
• 4 CHANNEL AMPLIFIER 3500 WATTS MAX MUSIC POWER

User questions & answers

Question:	anyonw knows what the 3 fuses on this are for
Answer:	They will pop before it blows your amp. Just like a breaker in your house.
Question:	would this amp be enough to push 2 rockford p3 dual 4ohm wire to 1ohm
Answer:	The amp is 1 ohm stable. I own the exact one. And it is great. The lowest resistance u are gonna get outta the subs is gonna be around 2 ohm being that they are 4ohm docs and not 2ohm dvcs
Question:	Will this push a 12” cobalt
Answer:	Yes it will push two 12", but you have to bridge it.
Question:	Would this run 2 mtx 10” 400 watt rms 4ohm subs if im not constantly at full power
Answer:	It should be fine I have a kicker comp r 800w rms it pushes it till I cracks and still has a lot of power left

Product description

Orion CB2700. 2 Cobalt Series 5400 Watts 2 Channel Amp Car Audio Stereo Amplifier

• RMS Watts @ 4 Ohm Stereo 14. 4V:   450 Watts X 2 Channel / RMS Watts @ 2 Ohm Stereo 14. 4V: 675 Watts X 2 Channel / RMS Watts @ 4 Ohm Bridge 14. 4V: 1350 Watts
• RMS Power Watts:       2700 Watts / Max Power Watts: 5400 Watts
• Frequency Response   10Hz~36KHz(-3dB)
• Signal Noise Ratio:       90dB
• Hi Pass Freq.    50Hz-4KHz / Low Pass Freq. 40Hz-500Hz

User questions & answers

Question:	I have 2 2ohm dvc punch subs. Would this amp for them 2 12s and give me that bass that would be nuts
Answer:	I used this for midrange and highs. It’s heats up too fast. Installed 3 12v fans under it. Base amp zapco if u can afford it.
Question:	is this a 1 ohm stable amp
Answer:	Hi, It is not a 1 ohm stable amp! It is a 2-Channel amplifier and can be run both 4 ohm or 2 ohm stereo mode! Thanks, Eclectic Mart

Product description

Lanzar Model : HTG888. 55000 Watt 8-Channel Mosfet Amplifier 8 X 250W RMS @ 4 Ohms8 X 350W RMS @ 2 Ohms4 X 1, 000W MAX @ 4 Ohms Bridged8 X 500W MAX @ 4 OhmsBass Boost CircuitBridgeable at 4ohms2 Ohm Stereo StableChrome RCA InputsStereo Line Outputs for Left and Right ChannelLow Pass Filter ControlsLPF Freq. Response: 40Hz-250HzHigh Pass Filter ControlsHPF Freq. Response: 40Hz-250HzBand Pass Filter ControlsBPF Freq. Response: 40Hz-3KHzPower and Protection LED IndicatorsSoft Turn-on/Turn-offTHD: S/N Ratio: 90dBChannel Separation: 65dBFreq. Response: 10Hz-45KHzFuse: 100ADimensions: 22. 83''(L) X 2. 24''(H) X 8. 81''(W)

• AUDIO EVOLUTION: This car speakers amp features regulated MOSFET Pulse Width Modulated that maintain rated power over a wide range of battery voltage. Excellent frequency response rates place these amps in a class of their own.
• INTELLIGENT DESIGN: The car audio amplifier 8 channel safety features include power and protection LED indicators; soft turn-on/off; and thermal, overload, and speaker-short protection.
• SOUND SPECIALIZATION: This high-powered Power Amplifier is cutting edge technology at its finest. Chrome RCA connectors and speaker screw-down terminals ensure a secure connection between amplifier and speakers that allow distortion-free sound.
• RCA JACKS: The Line-Out jacks allow you to build multiple amplifier systems without having to use splitter cords to distribute the signal. This makes it easier to bring one set into the first amp, then use the line out jack as the feed to the next amp.

User questions & answers

Question:	This Amp seems like a good deal, but the reviews are saying it craps out just after the warranty. How would I protect myself from getting scammed
Answer:	Who knows what the heck the true rating of this amp is. I did previously have a hifonics 5000 watt 5 channel amp and power does seem comparable.
Question:	this model has bluetooth
Answer:	Hi, our sincere apologies. There is no Line Output port for this model because that is supposedly for our HTG258BT model. You may check other details of the unit by visiting our website pyleaudio.com. Type the model number on the search box HTG888 for more details. Thank you.
Question:	How can this be a 5000 watt amp with a 100 amp fuse and 4 gauge wiring . Does'nt make since
Answer:	Look at the fuses.. example two 60a fuses 1200 including voltage, may see 1300 total power RMS in good soild electrical.
Question:	Where is Line out it advertised
Answer:	yes without any problem

Product features

Lanzar Amplifier Car Audio

• 8 X 250W RMS 4 Ohms
• 8 X 350W RMS 2 Ohms
• 4 X 1,000W MAX 4 Ohms Bridged
• 8 X 500W MAX 4 Ohms
• Bass Boost Circuit, Bridgeable at 4ohms
• 2 Ohm Stereo Stable, Chrome RCA Inputs
• Stereo Line Outputs for Left and Right Channel
• Low Pass Filter Controls, LPF Freq. Response: 40Hz-250Hz
• High Pass Filter Controls, HPF Freq. Response: 40Hz-250Hz

Features:

• Band Pass Filter Controls
• BPF Freq. Response: 40Hz-3KHz
• Power and Protection LED Indicators
• Soft Turn-on/Turn-off
• THD: <0.01%
• S/N Ratio: >90dB
• Channel Separation: >65dB
• Freq. Response: 10Hz-45KHz
• Fuse: 100A
• Dimensions: 22.83''(L) X 2.24''(H) X 8.81''(W)

Product description

6000W class D amp 1/2/4 ohm stable with Remote sub control

• 6000W Max Class D @ 1 Ohm, Stable at 2 Ohm and 4 Ohm with Bass Knob Included
• S/N Ratio > 70 dB with Frequency Response at 8 Hz ~ 180 Hz and THD < 0.2%
• Bass Boost Level 0 ~ 12 dB with LPF 40 Hz ~ 180 Hz and Subsonic Filter 0 ~ 50 Hz
• High and Low Level Inputs, Variable Low Pass Crossover, Variable Bass Boost
• Dimension ( L×W×H ): 431.5 mm (16.9 in) × 211 mm (8.3 in) × 64.5 mm (2.5 in)

User questions & answers

Question:	Will this push 2 12" pioneer bass with 2 ds1810" at the back and 8" in the doors
Answer:	it will fry them.
Question:	Which size speaker wire it'll take
Answer:	12 gauge wire
Question:	Will this amp push 4 15 planet audio speakers
Answer:	All depends on the ihms if you're dubs and wire configuration..wired right yes it should push them if it pushes anywhere bear its rated power.
Question:	What guage wire should be used to install
Answer:	Zero gage wire works best
Question:	Can ypu strap 2 of these together with ease
Answer:	yes, will strap together bought to buy another
Question:	You expect an amp to make that kind of power with 4 gauge wire
Answer:	I used adapters from o guage to 4 with decent electric and played daily cranked up for over two years! I totally stand behind this amp! I had two on 4 12” and loved it!
Question:	Will it push my sub?.. i have a 21" db. Rated 2500 rms
Answer:	Yes it will
Question:	Does this specific item come with 2 channels
Answer:	No, Mono Block 1 channel

Product description

Get more out of your car audio and take it to the next level of audio perfection with the unparalleled performance of the Rockford Fosgate 500 Watt Mono D Amplifier with Remote. This Rockford Fosgate is a quality made Mono D car amplifier rated at 500 Watt x 1 Channel @ 2 Ohms RMS. The amplifier features a MOSFET power supply, cast aluminum heatsink, muted turn on, short circuit protection, over current protection, RCA pass thru outputs, high level inputs, real time output and power supply thermal sensing, and phase switch. The amplifier is CEA 2006 compliant and comes with a remote bass control. Great audio starts with a great amp, so be sure to choose quality with the Rockford Fosgate 500 Watt Mono D Amplifier with Remote.

• 300 Watts x 1 @ 4-Ohms, 500 Watts x 1 @ 2-Ohms, Frequency 20Hz to 250Hz +/-1dB
• Onboard 12dB/octave LP/HP/AP crossover & Infrasonic filter. Power Wire Gauge- 4 AWG. Power Input Connector-Screw Terminal. Suggested Alternator-75 A
• On-board Punch EQ with +18dB boost at 45Hz. Input Sensitivity: 150 mV to 4 V
• Cast Aluminum Heatsink with Stealth top mounted control panel
• Includes wired remote (Punch Level Control). High efficiency amplifier design that reduces current consumption from the charging system

User questions & answers

Question:	Does the R500x1D come with the remote or is it sold separately
Answer:	It comes with the remote. I thought it didn't so I bought one for it and it already comes with it so I have two now
Question:	Does this amp provides High (Speaker) Level Inputs so it could be connected to a factory head unit
Answer:	I know this is late, but it may help others. Yes it does and you can tie into signal at rear speaker wires. The built in crossover will allow use of a sub woofer. Only drawback to this set up is that if you turn down head unit bass for doors ect. it also affects sub amp. HU built in crossover would be better for a balanced and more adjustable sound. This requires the HU to be upgraded however. A line output converter is a good option too even if you have low input ability. Makes for a neater install IMO. Bottom line is that it is dooable. Good amp too. Birthsheet is 648 watt @ 2 ohm 14.4 v on mine. In vehicle at idle in real life I average 629 using amp draw and voltage formula, I also own the P300-1 which pushes about 415 @ 2 ohm real life wattage. Birth sheet of 426. Banging for years in wife's ride on that one no issues. The new one rocks good so far in my ride. Love these amps. So much power for the size. Also as a D class amp they are efficient and take less away from the vehicle power system causing less strain. Bang some high power AB amps for a few years and your whooping on that alternator and battery shortening their lives. Less light dimming too.
Question:	Does this amp have an auto turn on feature so I dont have to wire up a remote turn on
Answer:	Another option in which I chose since it does need turn on signal is to use an added retained accessory power relay or just a simple relay. Your going to remove side panels to run RCA anyway so tap easily into a 12v power source when vehicle acc is on which can be found closest to amp position that is passing to rear of vehicle already. I used this one from Radio Shack. Model: 275-233 Catalog #: 2750233 0.5-AMP SPST REED RELAY AT 12VDC. This set up should be used to turn on multiple amps and relieve the head unit circuit. No tiny wire to run either. Although if this wire is just attached to RCA prior to install for a 1 amp install then this is the easiest way. If you use the relay then remember to fuse it to protect the head unit circuit.
Question:	is this amp 4 or 8 awg power and ground
Answer:	It has 4 awg connections for both power and ground. I am using mine with 8 awg wire and it runs perfect. I am not running it at max gain though. Only using it to run one 10" L7!

Product features

Prime 500 Watt Class-D Mono Amplifier

The Rockford Fosgate R500X1D is a quality made Mono D car amplifier that is rated at 500 Watt x 1 Channel @ 2 Ohms RMS. The amplifier features a MOSFET power supply, cast aluminum heatsink, muted turn on, short circuit protection, over current protection, RCA pass thru outputs, high level inputs, real time output and power supply thermal sensing, phase switch, the amplifier is CEA-2006 compliant and comes with a remote bass control. The dimensions are 8.50 L x 6.80 W x 2.00 H inches.