14 best receiver with ir remotes

Product description

Note:

The installation of electronic modules requires basic knowledge and requires a certain electronic professional foundation and hands-on ability. Please purchase carefully!

Manual measurement, with small error. Please check size in detail before purchase.

Real colors may slightly differ from the pictures, as it depends on specific monitor settings and light brightness.



We highly appreciate all customers opinions to improve the selling, also if anything you unsatisfied, please contact us for probable best solution.



Package Includes: 2Sets

1 set of lists：

1 X NEC IR Remote Control(not contain battery) .

1 X HX1838 remote module.

1 X 1838 Universal Receiving Head.

• Sensor uses HX1838, high sensitivity.
• Operating voltage 5V.
• Output form: Digital output.
• VCC: 3.3V-5V external voltage (can be directly connected to the 5v microcontroller and 3.3v microcontroller).GND: external GND.IN: external microcontroller I/O port, I/O port has been designed 10K pull-up resistor.
• Kit theory test distance of about 5-8 meters, but the practical application depends on the ambient factors you use, as well as the middle barrier (such as diaphragm, glass, obstructions or other material blocking), receiving head with HX1838 with power work instructions lights, receive 38K frequency any remote coding data.

Product description

The BAFX Products Extra IR Receivers are designed to be used with the BAFX Products SINGLE ZONE IR Repeater & Remote Control Extender Kits. You can use these IR sensors to expand your kit to cover more rooms in your home allowing you to control all of our IR devices from multiple locations. Kids have the television turned up too loud at night? Install an extra IR receiver in your bedroom so you can turn it down without getting out of bed!

Just like our remote control extend kit, our IR receiver will work with all makes/models of IR remote controls & devices from Charter, Cisco, Harmon Kardon, LG, Logitech Harmony, Pioneer, Roku, Samsung, Scientific Atlanta, Spectrum, Time Warner, Uverse, Yamaha & more!

Have a Problem using this with any device? No worries! BAFX Products has helpful, friendly, USA based support staff ready and waiting to assist you. They are well versed in getting things up and running as quickly as possible so you can relax and enjoy your favorite TV shows!

Specs

Overall length: 5 Feet

Cable length: 4’

Dual band compatible

Plasma resistant

25’ Maximum sensing distance

Up 45° Remote control angle

NO HASSLE 1 Year manufacturer warranty against manufacturing defects!

• EXPAND – Increase & Expand the reach of your current Single Zone BAFX Products IR Remote Control Extender kit! Add more receivers to more rooms to control your cable box, receiver, media player and more from more locations in your home, office or business.
• FUNCTIONALITY – Our IR sensors can receive signals from 25’ away and up to a 45° angle from the remote control. Can be used with any IR remote controls. Cable is 5’ long from tip to tip with actual cable length of 4’ 10”. Works with any Make model of remote controls as long as they use Infrared technology.
• COMPATABILITY – Compatible with the BAFX Products Single Zone IR Repeater / Remote Control Extender Kit ONLY! May not work with other brands of Infrared Repeater Kits! Does NOT work with BAFX Products Triple Zone or Wireless Kits!
• IMPORTANT – This IR Receiver is not designed to be plugged directly into a devices IR port. Doing so will not work and may cause undesirable operation of your device.
• WARRANTY – 1 Year warranty against manufacturing defects provided by BAFX Products. Don’t worry if something goes wrong, BAFX Products is ready to help with friendly USA based support!

User questions & answers

Question:	Will this work with the bafx bafx
Answer:	this item comes with an 8 inch extension rod, and additional ones are available for purchase its part number 1234
Question:	How well will this work in sunlight
Answer:	We don't have an ex5260 to test but from look at an image of the bottom of the projector, it looks like it will work with our mounting hardware. If it doesn't you can return for a refund. Cheers - Michael
Question:	Will this work if installed behind an acoustically transparent projector screen
Answer:	The ALZO suspended Drop Ceiling projector mount allows for positioning the projector left/right and front/back to balance the weight so that the assembly will hang straight down from the ceiling.
Question:	What is the outer diameter of the body of the peephole IR receiver
Answer:	No. The drop bar is a fixed length pipe. The projector is always fixed at the same height.

Product description

Is your living room cluttered with random A/V devices everywhere because they must be within the line of sight of the remote control in order for you to use them?

Are you tired of having to leave the doors on your TV cabinet open every time you find yourself watching television?

Do you want to move your devices into another room, a closet or the basement but still be able to control them with your remote control?

Remote Control Solution



The Supxing Infrared Extender Cable is the perfect solution for controlling a Blu-ray player, CATV box or another video source from your HDTV. Install where a soundbar that is blocking access to the HDTV IR sensor. Connect to home theater components that are concealed in a cabinet or nearby closet.



Important Notes

- Test the cable before attaching with the adhesive backing

- Check that the USB TV port provides 5V USB power or use a wall adapter

- Not compatible with set-top boxes using (RF) radio frequency signals

- Plasma TVs or CFL light bulbs can cause interference



IR Receiver for Hand-Held Remote

- Place in a convenient location near the display

- Transmits IR signal up to 15 feet from the handheld remote

- 180 degree operating range for receiving the signal

- LED flashes when a signal is received

Supxing usb ir repeater features:

*Power with a 1A USB wall charger

*20-60 KHz receiving frequency

* Flexible wire is easy to secure

• {IR REMOTE CONTROL} cable extends the signal to a video source like a Blu-ray player so it can be controlled from your HDTV; Red LED in IR Receiver bulb verifies the signal transmission(Operating range:20-60HZ)
• {HOME THEATER ACCESSORY} repeats the IR signal to a DVD player, STB box, Receiver or other A/V source with an infrared sensor; Route the cable out of sight with a wall mounted HDTV; Install the IR Transmitter end in a concealed equipment closet to hide a CATV box and control it remotely
• {SIMPLE INSTALLATION} of this lightweight IR cable; Locate the IR Blaster near the source sensor to repeat the signal to the source; Place the IR Receiver in a convenient location with line of sight of your hand-held remote; IR Tx and Rx cables have adhesive circles on the back for mounting
• {USB POWERED IR }extension cable has an integrated 6 foot Y-cable to receive 5V USB power; Connect to an HDTV USB port or to a USB wall charger(Tip: Devices that need remote control must be placed in a place where your remote control cannot be directly remotely controlled. Otherwise, the signal from the remote control and the remote control signal after forwarding will be sent to the set-top box at the same time. The signals are not synchronized and will interfere with each other and cause them
• {UNIVERSAL COMPATIBILITY} with most A/V equipment with infrared sensors (not RF); 180 degree IR Receiver angle provides plenty of leeway to get the right angle with your remote.Remote control signal receiving real-time response to fast forward without delay

User questions & answers

Question:	My Tvs IR receiver is blocked by sound bar will this work to move it is a better place to read remote
Answer:	Yes. It works very well. I use mine to control a set of speakers behind where I normally sit. Just used this to place the RF sensor in front of and it worked perfectly.
Question:	How do you configure the placement of the smaller end of the repeater near the cable box? Where should the adhesive be placed? This doesnt work
Answer:	Typically you are able to see where the IR sensor of the cable box is by shining a flashlight around the front panel of the box. The sensor window should appear different in color. Also it should round abouthe size of a dime or smaller. Stick the small end on that window, flat side down. Make sure the USB port that you are connected to is always powered. Or use a USB power supply. You aim your remote to the large end. That should work. If does not try using it on another device like a DVD player. If that doesn't work then you have a defective extender. Return it to Amazon and ask for another one. Hope this helps. I had no trouble.
Question:	Does everyone else have a green light showing it has power
Answer:	We have no green light. Only red light on larger receiver module which is on all the time. Works great!
Question:	Will this work with a TV cable box
Answer:	Yes! I have a Comcast Xfinity X1 DVR connected to it and for my Apple TV in the same area, they both work perfect.

Product description

IR RECEIVER CABLE.(PRODUCT DESCRIPTION)

Do you need an IR receiver that works perfectly, and will help put your Comcast Cable Box or other STP boxes out of view? If yes then you need our IR extender cable!.

Our 38-56kHz IR receiver will help you hide your entertainment systems in a less obtrusive view byextending the infrared signal received from the remote control and relaying via the wire back to the set top box or cable box. You may now hide it from view in a closet, cabinet, behind a closed door, in another room and still able to control it with your IR remote control.

WHY TRUST US?

Check out the features of our IR Receiver Cable.

1.EASY TO SETUP AND USE:

Plug the cable into the IR input jack located at the back of the STP box, then place the IR sensor receiver within a direct line of sight from your remote control.

2.CLEAN LOOK:

IR Extender Cable helps you to establish a clean,uncluttered look with no wires or cables in sight.

3.WIDE COMPACTIBILITY:

works with a wide range of Infrared remote control devices with a range of 38-56kHz.

Package Content:

2 x IR Receiver Cable

• ★ PLUG AND PLAY–Our IR extender cable is easy to install and use. Just plug the 3.5mm jack into an IR input port of the device.
• ★ UNIVERSAL COMPATIBILITY – Suitable for a broad range of 38-56kHzinfrared devices with an IR input port and remote control such as AV equipment and cable STB boxes.
• ★ 10FT CABLE – 10 feet(3m) LongCable with 3.5mm plug allows you to extend the signal receiver to a suitable position.
• ★ CLEAN LOOK:Our IR Repeater system is ideal for those who want to conceal their A/V component equipment inside a closet or cabinet for a clean, stylish look.
• ★ FLEXIBLE+ RISK-FREE PURCHASE–You can now control your home theater, cable boxes, etc. from behind thecabinet, closet or even the other room. If for any reason, you are not 100% satisfied with the product, you can send it back to us, and we will refund your money! DON’T CHECK THE NEXT LISTING! JUST ORDER NOW!!!

User questions & answers

Question:	Can this be used with a Xantech Connecting Block
Answer:	I dont believe so

Product description

Compatible with Dish Network 20.1 TV1 #1 Satellite Receiver: VIP 622, 722, 222, 522, 625, 942, 201, 211, 301, 311, 322, 351, 1000, 2200, 2700, 2800, 2900, 3000, 3200, 3700, 3800, 3900, 4000, 4100, 9200, 5200, 6000, 6100, 6131, 6400, 9242 HD PVR etc.

IR Signals Only and Just Compatible for TV 1

This Dish Network remote control can only use IR signals. And it needs a clear line of sight between the remote and the receiver. Please make sure there is no obstacle when using the Dish Network replacement remote.



This is a Dish Network 20.1 TV1 #1 Satellite Receiver Remote Control and it does not surpport the UHF PRO function and not work for TV2. Please do not buy a wrong remote that not work for your device.

Package Content:

2x Remote Control ( Batteries are NOT included )



Kindly Note: This Dish Network 20.1 TV1 #1 Satellite Receiver IR Remote Control compatible with most Dish Network and Bell Satellite Receivers. But it may not be able to control your other devices, such as LED TVs and speakers.

• The Dish Network 20.1 TV1 #1 Satellite Receiver Remote Control is very lightweight and ergonomic, and does not require a lot of space and comfortable to hold by your hands.
• No programming or paring needed. Just install new 2 AA batteries and you're good to go
• Compatible with Dish Network 20.1 TV1 #1 Satellite Receiver: VIP 622, 722, 222, 522, 625, 942, 201, 211, 301, 311, 322, 351, 1000, 2200, 2700, 2800, 2900, 3000, 3200, 3700, 3800, 3900, 4000, 4100, 9200, 5200, 6000, 6100, 6131, 6400, 9242 HD PVR etc.
• The Dish Network 20.1 TV1 #1 Satellite Receiver IR Remote Control is a replacement IR remote control and it does not surpport the UHF PRO function and not work for TV2.
• Kindly Note: Dish Network 20.1 TV1 #1 Satellite Receiver IR Remote Control compatible with most Dish Network and Bell Satellite Receivers. But it may not be able to control your other devices, such as LED TVs and speakers.

Product description

2.4GHz AV Sender Audio Video Wireless Transmitter Receiver IR Remoter

with IR Remote Receiver

The product consists of a transmitter and a receiver. It adopts an advanced 2.4GHz wireless transmission scheme and has the advantages of a long transmission range, strong anti-interference and high mobility.

It can transmit AV signals of DVD, DVR, CCD camera, IPTV, satellite set-top box, digital TV set-top box and other similar devices, by means of radio waves and receive them at distant end and input them to a TV set to be displayed.

Moreover, the IR remote controller can be used at the receiving end to realize the function of wireless control of devices from another place. It enables you to easily realize wireless sharing of HD AV data and enjoy untrammelled hi-fi audio and visual effects.

Use 2.4GHz ISM frequency band.

150 m transmission range without any holdback.

8 groups of selectable channels, it can effectively avoid the interference from router and other wireless device.

Support 1 group of AV signal input/ output.

Keep Transmitter and receiver setting at the same channel, it can support 1 transmitter and more receivers at the same time.

Support DVD, DVR, IPTV, CCTV Camera, Satellite receiver, Digital STB and other AV output devices.

Support superheterodyne 433MHz infrared remote signal transmission, while Compatible for 38KHz infrared carrier control signal.

Transmitter have built-in infrared signal emission or infrared transmission extension cable, so that you can do remote control the signal from DVD, DVR, STB, IPTV, and other device.

Supports video transmission of PAL/ NTSC system and stereo audio transmission, Pictures received are clear, flamboyant and stable.

Full hardware design without installing any software, plug and play, simple and convenient.

Output resolution: 720 x 480P

Specifications:

Tr

• 150 m transmission range without any holdback.
• Keep Transmitter and receiver setting at the same channel, it can support 1 transmitter and more receivers at the same time.
• Support superheterodyne 433MHz infrared remote signal transmission, while Compatible for 38KHz infrared carrier control signal.
• Transmitter have built-in infrared signal emission or infrared transmission extension cable, so that you can do remote control the signal from DVD, DVR, STB, IPTV, and other device.
• Full hardware design without installing any software, plug and play, simple and convenient.

Product description

The BlastIR Wireless Pro supports up to 10 zones with independent sending/receiving frequencies. (kind of like different channels on a walkie-talkie). You can change the zone by using a very small rotating switch located at the bottom of the receiver and emitter pucks. The Receivers will only communicate with the Emitters that are set to the same zone.

• Note: This listing is for the "Transceiver" unit only. It is a single unit that both receives and emits an IR signal. It is recommended that this be used to exapand an already existing setup or to purchase two units so that it may work over a long distance.
• Control all of your home theater video sources (Blu-Ray player, Cable box, TiVo, and anything else that uses a standard IR remote control) from behind walls or closets by extending the IR signal with this kit.
• It can be combined with other BlastIR Wireless Kits to be used as an "All-to-All" setup, or to create "zones" and only control specific devices.
• Wireless Distance: 200m (650ft), distance may vary due to obstacles, IR Receiver Distance: 7m (30ft)
• IR Frequency: 20-60Khz // RF Frequency: 915Mhz

User questions & answers

Question:	need to extend IR capability of my Denon remote to the receiver, which is located in the lower level of the home. Is this the right product
Answer:	No, it will not. Different size mounting plate and the 1450 is too heavy for the ball joint mount model. Here's a link to our mounts compatible with the 1450: https://www.amazon.com/s?k=powerlite+1450&me=A2OJEQZWEHARE7&ref=bnav_search_go Regards, Bryan PCMD, LLC.

Product description

• NEW Replacement for Dish Network 20.1 IR Satellite Receiver Remote Control
• The remote control is not a universal. You can check whether each button or model of your original remote control is the same before you buy it.

• NEW Replacement for Dish Network 20.1 IR Satellite Receiver Remote Control
• Use:Universal IR Remote Control for Dish 20.1 Network Dish-Network IR Satellite Receiver Device Code W/SAT TV DVD models VIP 622 722 222 522 625 942 201 211 301 311 322 351 1000 2200 2700 2800 2900 3000 3200 3700 3800 3900 4000 4100 9200 5200 6000 6100
• conpatible with:DISH 20.1 It is NOT original remote
• Package contain: 1 remote Only, batteries and instruction are Not included
• Standard shipping, almost 7- 25 days to arrive ( if not received over 25 please kindly contact us)

Product description

The IR sensor cable could be plugged into an IR repeater/extender or A/V extender and serves as the external IR sensor for receiving the command signal emitted from an remote controller.



It could also be plugged into a video equipment that can support IR plug-in such as cable box, satellite receiver, home theater system and serves as an extended IR probe for receiving the input of IR remote control signal.

[Note]: Not all audio/video equipments or extender kits offer such IR plug-in. Please check your video equipment first before purchase.



Its paired IR blaster/emitter wire is designed for blasting the IR remote command toward the A/V equipment to be controlled so the audio/video source equipment at distance can perform the commanded tasks such as play, pause, power on/off, volume up/down, channel +-, record and so on.



Each standard package includes 1 of IR remote sensor wire and 1 of IR remote blaster/emitter wires. Each wire has the same length of 6.5 feet.



Easy Wire Extension

Both the IR blaster/emitter wires and the IR sensor wire all use the standard 3.5mm headphone plug. If you wish to extend these wires for longer cable length in the setup, you can simply use longer 3.5mm or 2.5mm audio extension cables to join with these IR input/output wires for cable extension if needed.



IR Remote Sensor Wire

The IR remote sensor wire is used for receiving the control commands emitted from IR remote controller. It could be plugged into a video source device that can support IR plug-in or video/audio extender and serves as the IR sensor probe for receiving the input of IR remote control signal.



IR Remote Blaster/Emitter Wire

The IR blaster/emitter wire is used for blasting the IR remote control signal toward the A/V equipment to be controlled to perform the desired tasks.

• Both the IR blaster/emitter wires and the IR sensor wire all use the standard 3.5mm headphone plug.
• The IR remote sensor wire is used for receiving the control commands emitted from IR remote controller. It could be plugged into a video source device that can support IR plug-in or video/audio extender and serves as the IR sensor probe for receiving the input of IR remote control signal.
• The IR blaster/emitter wire is used for blasting the IR remote control signal toward the A/V equipment to be controlled to perform the desired tasks.
• Both IR remote sensor and blaster/emitter wire length at 6ft.

• IR remote control cable extends the signal to a video source like a Blu-ray player so it can be controlled from your TV; Blue LED in IR Receiver bulb verifies the signal transmission
• Home theater accessory repeats the IR signal to a DVD player, STB box, Receiver or other A/V source with an IR sensor; Route the infrared remote control extender cable out of sight with a wall mounted TV; Install the IR Transmitter end in a concealed equipment closet to hide a CATV box and control it remotely
• Simple installation of this lightweight IR cable; Locate the IR Blaster near the source sensor to repeat the signal to the source; Place the IR Receiver in a convenient location with line of sight of your hand-held remote; IR Tx and Rx cables have adhesive circles on the back for mounting
• USB powered IR extension cable has an integrated 6 foot Y-cable to receive 5V USB power; USB cable on the IR remote extender cable connects to a TV USB power port or to a USB wall charger
• Universal compatibility of IR extender cable with most A/V equipment with infrared sensors (not RF); 30 degree IR Receiver angle provides plenty of leeway to get the right angle with your remote

User questions & answers

Question:	Will this work with newest Spectrum Arris device
Answer:	It works with my new Arris DCX3510M HD DVR box. However the IR reception range is only 7-8 ft max. And you will need a separate USB power supply because the Arris USB ports only work when the box is on.
Question:	How close does the IR emitter need to be to the device receiving the signal
Answer:	The smallest one needs to be right on point to work. You will need a second person to help while you adjust and they try the remote.
Question:	Does it have to be Synced to the remote
Answer:	No. This is a simple device that simply passes on the infrared signal. Whatever the remote shoots into this device's receiver will be transmitted to the other end. It took only minutes to set this up. We put cable box behind the TV screen. Attached the receiver end to the underside of the TV, near current remote sensor just so it is the same target area you are used to, the other end of the extender gets aimed at the cable box on the other side. The cable box has USB so that was used for the power. Amazing product
Question:	What does 10feet mean
Answer:	Means 10 feet long from starting to end.

Product features

Remote Control Solution

The Cable Matters Infrared Extender Cable is the perfect solution for controlling a Blu-ray player, CATV box or another video source from your TV. Use your TV remote even when a soundbar is blocking access to the IR sensor. Connect to home theater components that are concealed in a cabinet or nearby closet.

Important Notes

• Test the cable before attaching with the adhesive backing
• Check that the USB TV port provides 5V USB power or use a USB wall charger
• Not compatible with a set-top box using (RF) radio frequency signals
• Bright sunlight or CFL light bulbs can cause interference

USB Power Boost

• Power with a 1-amp USB wall charger
• USB Y-cable length = 6 Feet

IR Compatibility

• 30-60 KHz receiving frequency
• CFL bulbs or bright light can cause interference

Lightweight Extender Cable

• Flexible wire is easy to secure
• Coil any excess wire with a cable tie

• [High sensitivity]:Remote control signal receiving real-time response to fast forward without delay. Bullet Point
• [Wide frequency design]:Receive wide frequency, which allows users no longer because of remote control receiving frequency mismatch caused by remote control is not sensitive or can not control.
• [Wide compatibility]:Apply to almost of the wide-electrical set-top boxes, telecommunications set-top boxes, other network set-top boxes satellite pan set-top boxes. Bullet Point
• [USB port]:Support LCD TV, set-top box and mobile phone USB charger to obtain the power.
• [Easy to use]:Attach the transmitter to the remote control receiver, the receiving end is affixed to a position where the remote control signal can be easily received, then plug in the power supply to use.

User questions & answers

Question:	Can you use it to decode Infrared codes
Answer:	Just messured mine for you, it's 1 1/2 inch by 4 3/4
Question:	will this work to control fire tv
Answer:	Hi, Yes. If your projector model is listed in the title of the item, then the mount you will receive is guaranteed to fit those projector models. Regards, Bryan Projector Ceiling Mounts Direct, LLC.
Question:	will this work to control fire tv
Answer:	Yes. This mount is also compatible with the Home Cinema 1040. Regards, Bryan Projector Ceiling Mounts Direct, LLC.
Question:	Does it work with mac mini? my mac mini IR receiver not working
Answer:	No. Visit this link for mounts compatible with the PowerLite 96W - https://www.amazon.com/s?k=powerlite+96w&me=A2OJEQZWEHARE7&ref=nb_sb_noss Regards, Bryan Projector Ceiling Mounts Direct, LLC.

Product features

Why Do You Choose US?

We've been working in electronics for years and accumulated rich experience, and now we want to share our products'preferences and ingenuity for you to bring you a more fashionable and artistic life experience.

BUY WITH CONFIDENCE - There are plenty of standard similar products on the market to choose from. Why buy from us? Simple: Peace of mind at your special event. We're obsessive about making sure that each one of our product is produced to the highest standard that we ourselves would expect. From the quality, size, color, Appearance, practicability and application of each product, we take pride in considering from the customer's point of view. So relax, we got you covered!

As a reliable seller, we always try our best to provide good quality products as well as excellent service to our customers, your trust and business is that important to us. If you are not 100% satisfied with the quality of the product, pls feel free to let us know about the issue, you will be assisted ASAP.

Product description

Multizone: Protect from Interference Most IR extenders are programmed to pass any signal that is sent through the receiver. Sometimes this may disrupt your setup as a few devices in your closet run on a similar IR frequency and cause interference with one another. The Multizone feature protects your devices from interference from other devices. This gives you the ability to have certain devices controlled only from specific areas in your setup. This has been a requested feature from many of our customers as they have extended IR signals but unintentionally were controlling two devices located in the same space. Cable boxes have especially been a pain since multiple cable boxes are easier to have based in the same area. Now with the BlastIR Wireless Multizone you are able to ensure you will only control the box that is attached to one of your TVs and not the other. The Channel IR System The Multizone feature works on a 10-channel system, this system gives you the ability to interact with your devices without needing to worry about your Wireless Extenders interfereing with one another. The system also gives you the option of using any number of transmitters or receivers on any given channel. This gives you complete freedom of choice for where your displays and devices can be placed without having to complicate your setup. The BlastIR Wireless Multizone Receivers will only communicate with the BlastIR Wireless Multizone Emitters that are set to the same channel. If you happen to own the classic BlastIR Wireless, this product will also work with it. Channel 0 on this product will allow IR signals to be sent between the two diffferent versions.

• NOTE Some devices us RF instead of IR for remote control. The Blast IR Wireless Pro only works with IR devices.
• 10-channel system that gives you the ability to interact with your devices without needing to worry about your Wireless Extenders interfering with one another
• Included USB and AC power cables, extra IR cables, mounting adhesive, and rubber feet
• Known compatibility issues with: Yamaha HTR 6140 and Arris DCX 3520E-M
• Control any IR device from a distance. Blu-Ray Players, Cable and DVR Boxes, AV Receivers, Logitech Harmony Devices, Anything else that uses an IR signal!

User questions & answers

Question:	I can't figure out where the connections (V+/G/ST/IR) go from the wall receiver to the main unit (+12VDC/GND/Status/Signal) - help pls
Answer:	They connect from from the receiver to the main unit via standard telephone cable (CAT3) not supplied. V+ is +12VDC, G is GND(or the minus side of the power supply), ST is the status LED and IR is the signal.
Question:	Does this work with FIOS 7xxx HD DVRs
Answer:	It works perfect with va comcast DVR. So I magazine other DVRs will work. You'll have to find the right spots to place the 2 sensors for best performance. The only device that the infrared device doesn't work well with is an older Sony reciever I have hooked up. I only get volume control with this.
Question:	What is the maximun length of cable that the BlastIR can support? Will it reach over 150ft Cat5e cable to send it's repeated signal
Answer:	Yes.
Question:	can I operate 2 televisions off of 1 cable box
Answer:	I have a TV and cable box in my man cave and HDMI ran overhead to a TV in adjoining exercise room. I have an HDMI splitter in the man cave. I want to simply be able to use the cable remote from the man cave TV to change channels from the exercise room, going through one wall. I'll just take the remote to whichever room I'm in. Do I need anything else other than this item. I couldn't ask all this in the questions, maybe someone will see this answer, sounds similar. I'm already operating 2 TVs off a single cable box with a splitter but want to use the remote in both rooms.

Product features

Multi-Zone Control

The BlastIR Wireless Pro supports up to 10 zones with independent sending/receiving frequencies. (kind of like different channels on a walkie-talkie). You can change the zone by using a very small rotating switch located at the bottom of the receiver and emitter pucks. The Receivers will only communicate with the Emitters that are set to the same zone. You can also purchase extra Emitters, or Receivers individually if you do not need an extra full pair.

All-to-All

The BlastIR Wireless Pro can be set to send the signal from All Receivers To All emitters by setting all the units to the same "Channel" or "Zone"

Zone-To-Zone

The BlastIR Wireless Pro can be set to only send the Signal from one Receiver to specific emitters.

Troubleshooting and Support

Troubleshooting: If you're having trouble setting up your BlastIR PRO, it is very easy to troubleshoot. The videos on Sewelldirect will show you how easy it is to set up and troubleshot your BlastIR.

Please Note : This product is NOT Compatible with the Yamaha HTR 6140, Arris DCX 3520E-M, or the OSD ATM-7 Speaker Selector.

Product description

The Irdroid Wireless IR Extender is very useful in situations where your STB, Music receiver or any other IR controlled equipment is hidden behind the TV or somewhere behind walls, in other rooms or in a cupboard, or when a bigger distance need to be covered (up to 200 meters). The Irdroid Wireless IR Extender has IR receiver and IR transmitter. When a signal is received via the IR receiver it directly goes to the ir transmitter via radio signal link and it is immediatly emmited.

Features:

– DC 5V power input

– Supports 38 and 56 KHz IR signals (selectable via switch)

– Small form factor

– up to 200 meters range between the transmitter and the receiver

– Easy installation

Sample usage:

– Extend Tv, STB, etc. IR range

– Extend IR range for digital signage solutions

- Extend range for Irdroid IR products

• Long Control Distance: Reliable(stably without delay) and up tp 650ft long-range wireless infrared IR reception and transmission.
• Wide Compatibility : Compatible with most of IR controlled devices, eg, DVD、DVR、IPTV, satellite set-top boxes, digital TV set-top boxes, PC and so on. Let your life be simple with Pakite transmitter and receiver kit.
• Dual Band: Carrier frequency 38KHz/56KHz(manual switch on the Receiver end) Frequency 433.92MHz ±500kHz Superheterodyne.
• Compact and Double Modes: A smaller footprint than many other kits on the market to help save space, two Power Supply Modes (USB or Battery power supply) for your choice. Note: We suggest to use USB power supply for the receiver because of the big power consumption.
• Warranty & Support: We promise you a 30-Day Money Back Guarantee and 90-Day Limited Product Warranty. 24hours online customer service.

User questions & answers

Question:	Unit doesn’t work. Out of 30 day Amazon window. Anyone know who to contact and how
Answer:	They came with very little instructions. I just wrote them off as a loss.
Question:	Unit works great on my tv. how do i keep it from controlling someone elses unit approx. 300 ft away and vice versa? i can control his tv
Answer:	Hello,thanks for your question,within the effective range, the same people use 435, and the controlled equipment is the same. If it is the same device, it couldn't do that current!
Question:	I am concerned about the Infrared emitter transmission range (I need to use this for a theatre play). Will the emitter transmit at least
Answer:	Yes, sure IR range is at least 10 meters and the distance between transmitter and receiver can be 200 meters
Question:	Dose the usb plug into a charger that plugs into a wall 110 v
Answer:	Yes plug into a usb charging system. If the units stop working after a few days the problem is not the batteries Using the usb power will not make the units work

Product features

PAKITE IR Remote Extender

The PAKITE feature protects your devices from interference from other devices, this system gives you the ability to interact with your devices without needing to worry about your Wireless Extenders interfereing with one another. They are more convenient to use than cable boxes, and can save your space, making your home neater. It is worth of you bringing them into your home!

Used for all kinds of remote control

Compatible with most of IR controlled devices, eg, DVD、DVR、IPTV, satellite set-top boxes, digital TV set-top boxes, PC, air conditioning and so on. Let your life be simple with Pakite transmitter and receiver kit.

Super Long Control Distance, Small size, Two modes of power supply

Reliable(stably without delay) and up tp 656ft long-range wireless infrared IR reception and transmission. This wireless remote control transmitter and receiver system kit allows you to go from room to room and control devices through walls, doors, ceilings, floors, etc.

A smaller footprint than many other kits on the market to help save space

Two Power Supply Modes (USB or Battery power supply) for your choice.

270° wide-angle infrared emission and dual band makes the signal more stable. Carrier frequency 38KHz/56KHz(manual switch on the Receiver end)

Package Include:

1*IR Transmitter (TX)

1* IR Receiver(RX)

2*USB cable

1*User Manual

1*IR Extender Cable

Put the transmitter bulging "set-top box" 1-2cm.

Transmitter

1. Transmitter Frequency：433.92MHz ±500kHz Superheterodyne

2. Carrier frequency：38KHz/56KHz

3. IR signal Transmitting：≤10m, 33ft

4. Power Input: 5V 100mA, or two batteries of AA LR6 1.5V

5. Size: 12×8×7cm (4.7x 3 x 2.8 inches)

Use the external IR Extension cable to place the transmitter, Align line top with the front of the device

Receiver

1. Transmitter Frequency：433.92MHz ±200kHz Superheterodyne

2. Carrier frequency：38KHz/56KHz(manual switch)

3. IR signal Transmitting：≤5m, 16ft

4. Power Input: 5V 100mA, or two batteries of AA LR6 1.5V

5. Horizontal barrier-free transmission distance：≤200m (656ft)

6. Size: 12×8×7cm (4.7x 3 x 2.8 inches)

Product description

Color: Black With 1 receiver which picks up the signal from the remote controller, the receiver is with a convenient IR confirmation . With 1 emitters which is used to send the signals to the A/V components. 5V USB AC Power Supply. 34-60kHz operating range. This IR Repeater System Kit allows you to control home theater devices/components which are kept behind closet doors or in a closed cabinet. Or do you want to control an IR signal devices between two rooms such as adjusting the volume of the amplifier from somewhere? This item allows you to use an existing infrared remote controller to operate an audio/video (A/V) component. For example: amplifier, cable box, stereo receiver, satellite TV receiver, CD player, DVD player, Blu-ray player or any other components which is controlled by IR signal.

• Package Content:1 x IR Receiver 1 x IR Emitter,USB Adaptor
• Infrared Remote Control Receiver
• Emitter
• USB Adaptor
• Easy Installation: 1. Stick the Receiver in a convenient location that you want with the included double sided tape. 2. Stick the IR emitters (the smaller one) on devices that you want to control.

User questions & answers

Question:	will this work with directv
Answer:	It's about 4 x 6 inches.
Question:	Will this work on ARRES DCX3200-M and /or DCX3600-M ? any info appreciated
Answer:	It depends on the size of the mini projector. The ability to adjust the support beams is not very flexible, but I used this for a standard-sized projector. My guess is that this product would not work for a mini projector, but I can't say for sure without knowing its dimensions.
Question:	Will this work with Scientific Atlanta settop box
Answer:	Nothing fits.
Question:	Does this come with the 5v USB power adapter to plug in for power? Doesn't show in the picture or content, but clearly needs one
Answer:	Projectors vary but there sould be a couple of screw sizes included.