13 best auto jacks

Product description

Fit Under Low Ground Clearance Vehicle

Pro-Lift F-767 Grey Low Profile Floor Jack is a 2 Ton floor jack that give you better access to low ground clearance vehicle. And,give you the lifting range from 3-1/2 inches to 14 inches.

The Jack can be fit under a clearance of 3-1/2 inches and maneuvered easily into position.

Pro Lift F-767 floor jack also features the heavy duty steel construction that provides the long lasting durability.

Pro Lift unique patented bypass device protects against over pumping. Its built-in safety valve provides overload protection.

- Extra Low Profile

- Lifting Range from 3-1/2 inches to 14 inches

- Patented bypass device protect over pumping

- Built-In Safty Valve Provides overload protection

Pro Lift F-767 floor jack is backed with SFA 90 Days Warranty from the Date of Purchase.

Take one now to access to the areas you never access before.

• Extra low profile
• Lifting range of 3-1/2 inches to 14 inches
• Patented bypass device protects against over pumping for safe operations
• Built-in safety valve provides overload protection. Rust Resistant
• Heavy duty steel construction provides long term durability

User questions & answers

Question:	Does it come with a portable case
Answer:	No, but the box it comes in is pretty sturdy. If you remove the cardboard packing the jack easily slides back into the box. The inside bottom of the box is reinforced. Not sure how long it will hold up, but it’s better than nothing.
Question:	Will this raise a 2011 cadillac cts enough to get jack stands underneath it? i want to change transmission oil ... thanks
Answer:	A Cadillac CTS is roughly 4,300 pounds. Which is a little over the capacity of this jack. As long as you're placing it on jack stands and you don't leave the jack holding it too long, it should be okay. Although all the armchair experts on this site will implore you to buy a 3 or 4 ton jack. Just remember to always put the car on jack stands and do your work on a flat, level surface.
Question:	Can anyone tell me the outside diameter of the lifting cup? Thanks
Answer:	The cup itself is 2 1/4 inches, with the inner portion (The part that spins freely, with the 4 tabs) 1 7/8ths, and the tabs extend about 1/4 inch up from the cup. Hope this helps.
Question:	What kind of oil does this take? The screw was loose when it was shipped to me and some oil had poured out into the box. I just want to top it off
Answer:	hydraulic jack oil. The screw IS loose upon arrival. If you read the SHORT instructions....this (grey) screw is HOW TO LOWER the jack when you are done lifting and have supported the weight/vehicle with jack stands. Turning just a bit using the handle you used to pump up the vehicle - you will notice it lower ever so gently. ONCE it is fully lowered - it is best to immediately turn the screw clockwise until it stops - this prepares the jack for its next use. Do this so you will not forget it is closed. IMO - some people with oil spewing - did not 'get it' how important it is to assure the valve is closed BEFORE raising the vehicle.

Product features

Pro-Lift F-767 Grey Low Profile Floor Jack - 2 Ton Capacity

About Us:

Our ProLift hydraulic automotive jacks, lifts and garage equipment range will cater to many 'do it yourself' enthusiast. The product line includes bottle jacks, floor jacks, garage jacks, aluminum jacks. scissor jack, lawn mower lifts, utility lifts, chokes, dirt bike lift, creepers, mechanic seats and more! Explore our range on the products page.

ProLift has become a global presence in the go to automotive garage maintenance equipment with locations in the United States, The Netherlands, Taiwan and Australia. We create dependable and reliable performance hydraulic equipment.

Product description

Pro lift T-6903D is a 3-ton double locking jack stands. It features a high quality cast ductile Iron Ratchet bar and sturdy stamped steel base provide durability and longevity which makes ideal for home, professional and farm use. Always used in pairs, counter weighted pawls serve as a safe secure locking device to prevent the load from accidental disengagement. An attached pin lock provides support, locking the ratchet bar in place for an additional carrying point. One piece, multi position ductile ratchet bar provides strength and durability as well as a quick adjustment mechanism that securely locks into the desired position.

• Sturdy stamped Steel Construction with 3 ton capacity
• High quality cast ductile iron ratchet bar
• Double locks mechanism with both handle locks and mobility pin
• Height adjustment mechanism allows smooth upward movement while release handle locks and mobility pin
• Meets or exceeds ANSI/PALD standards. Ideal for home, Auto, truck service, farm, and shop use
• Fit type: Universal Fit

User questions & answers

Question:	Where can I buy just the locking pin
Answer:	Max 16 1/2 min 11 inches
Question:	what is the extended maximum height
Answer:	It mounts to the Smittybilt Pivot hinge, so it will clear most aftermarket bumpers as long as they don’t have an integrated tire carrier.
Question:	Does it come with 2 or just one jack
Answer:	No
Question:	What are the max and min lift dimensions
Answer:	I use an insulator for the handle but the mount is very secure and makes little to no noise compared to my old one.

Product features

Pro-Lift Double Pin Jack Stands - 3 Ton

Features:

• Sturdy stamped steel construction
• High quality cast ductile iron ratchet bar
• Height adjustment mechanism allows smooth upward movement while release handle locks into position
• Ideal for auto, truck service, farm and shop use

• ✅ SPECIFICATION - Maximum lifting weight: 1.5 Ton (3,300 lbs). Lift operating distance from 4.13 inches to 15.15 inches. Net weight 5.34 lbs (2.42 kg).
• ✅ SMART MECHANISM - 90% less effort required to lift your vehicle with the innovative ratchet system.
• ✅ FLAT TIRE REPAIR - For any emergency, this Scissor Jack will help you change your tire fast and easy.
• ✅ UNIVERSAL - Designed to fit any vehicle: sedan, coupe, SUV, MPV, hatchback, crossover, wagon and more.
• ✅ GUARANTEED PURCHASE - We know you have options here, and we know that our quality is superior, so we want to make the best choice the easiest one. That's why we will refund you 100% if you have a single concern about ANYTHING. Just send it back our way for a replacement or full refund! The choice is yours.

User questions & answers

Question:	will this work on a 98 acura integra
Answer:	I returned this jack because it was sub par .. scissor jacks work on any vehicle with the proper jacking points.
Question:	Can the alignment head be removed or replaced so that heavy items other than a car can be lifted
Answer:	The alignment head is held by a large rivet.
Question:	This will works with Dodge Dart 2014? Thanks
Answer:	Yes. It works perfectly for that car model.
Question:	Will this fit in the jack compartment of a 2010 jeep wrangler jk
Answer:	What is the width and length, and height? Measure your jeep and check the measurements of the jack.

Product features

Scissor Jack for Car

Package Include:

• 1 x Scissor Jack 1.5 Ton
• 1 x Ratchet
• 1 x Product Manual
• 2 x Car Air Fresheners

How to use?:

1. Insert the jack handle into the hole of the handle socket.
2. Make sure that the saddle is correctly positioned. To prevent damage to the jack, do not move the jack while the handle is intact in the socket.
3. To raise load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle clockwise.
4. The ratchet does not rotate until there is pressure on the jack head (at the beginning you can turn it with your hand).
5. To lower load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle counterclockwise slowly.

Product description

The Arcan ALJS3 3-Ton Steel Jack Stands has an overall 3-Ton lifting capacity and a working range of 11-5/8 in. to 17.5 in. A counterweighted pawl locks in place securely to prevent slipping, while allowing easy adjustments. A large contoured saddle with locating lugs helps support and position vehicle frame. The wide stance base delivers superior stability and includes base pads that prevents the jack from sinking into asphalt and provide stable footing for the jack stands. The welded construction and alloyed steel offer years of support. Arcan puts all of our lifting equipment through voluntary and rigorous third party safety testing, as outlined by the ASME PASE-2014 Safety Standard for Portable Automotive Service Equipment, to ensure that our products are among the safest on the market.

• COLORS MAY VARY: ALJ3T (silver) or A20018 (green)
• LIGHTWEIGHT AIRCRAFT-GRADE ALUMINUM: Allows for easy maneuverability.
• DUAL PUMP PISTONS: Quickly raises the floor jack saddle to load.
• REINFORCED LIFT ARM: Increases strength, chassis torsion control, and durability.
• VEHICLE PROTECTION: Designed with a rubber saddle and a foam handle bumper.
• SIDE-MOUNT HANDLE: Allows for convenient jack positioning.
• 2 PIECE HANDLE: Allows for easy storage.

User questions & answers

Question:	how smoothly and slow can a vehicle be lowered
Answer:	This fuel pressure reghulator is set at 43 PSI - identical to the OEM regulator. -Sean 818-574-FUEL
Question:	What is the height range
Answer:	Yes, this will fit the 2013-2018 Can-Am Maverick / Maverick Max 1000 . -Sean 818-574-FUEL
Question:	How big is the saddle and rubber pad on this jack
Answer:	This will be a 100% direct fit for the 2009-2018 Outlander 650. -Sean 818-574-FUEL
Question:	where is arcan made
Answer:	Yes, this will be a 100% direct fit for the 2013-2015 Can-Am Maverick 1000. -Sean 818-574-FUEL

• Dimensions: 9.75"L x 9.75"W x 12.25"H. Patented design combines jack stand and bottle jack in one unit
• Safety bar locks unit at desired height. This jack is for trucks and off road type vehicles
• Portable jack designed to safely Lift and hold both Regular and unibody cars and trucks
• Highly durable. Wide steel base for stability under load. Height range is 11 inch to 21 inch, but its default lift range is 11 to 17.25 inch, it can be raised to 21 inch if adjusted manually
• Strong safety bar keeps jack from lowering once it has been raised to maximum height

User questions & answers

Question:	I lost the jack arm, how can i get a replacement
Answer:	I purchased the jack to jack up my utility trailer. Tractor Supply used to carry this jack, they no longer carry it., so I went on line & Found that Powerbuilt is the manufacturer.... Google them, & send them a note, about needing the jack arm.
Question:	How do you release the safety latch? Help
Answer:	Raise the jack, lift the latch while lowering the jack.
Question:	What is the exact measurement of this jack? For storage purpose
Answer:	I measured it in half light so do not bet the farm on the answer but it should be close. The base is 9"X9" and it is nearly 13" tall. That will get you close.
Question:	I see a lot of bad reviews on quality, does anyone know if they are better built now? Has there been a quality control or design improvement
Answer:	You must be working for a company that does not make or represent the Powerbuilt name. By your question about quality, you are going off of rumors and gossip.I have been in the very dangerous employment of glazing, sandblasting, industrial coating, waterproofing, painting, industrial and commercial building repair, and skyscraper window washing. Safety and quality of tools for myself and my crew is my first concern. I actually was a consultant for Landa Pressure Washers,and many Industrial Chemical Companies like Shermiin Williams and Miller Paint. Many things can go wrong when you'r 80 feet up on a crane at the shipyards,or sandblasting, testing , and coating a Bridge in Portland Oregon, or just fixing your truck or car. Powerbuilt tools, and especially this #640912 keeps me verysafe, better than a car jack alone or a jack stand alone. Look up what the Fire Departments and first responders use at your local Safety Equipment Supplier.Look up the Fisk Descender, a safety device made by my previous employer and inventor, Brian Fisk. We used this safety device to descend from buildings andCranes, and Holding Tanks at the Refineries. I pressure washed 8 to 10 story buildings hanging to prep them for coating or waterproofing or caulking. When I needthe safest support product I know to crawl under and work on a heavy machine or vehicle or industrial motor at Frito Lay or a support beam at Robinson Dairy, you'llsee this Powerbuilt 640912 keeping me safe. Now that I am retired from the Industrial world, I will continue to stand by and consult and train people with manyother Powerbuilt products.

Product features

Powerbuilt 3 Ton All-in-One Jackstand/Bottle Jack

The Powerbuilt 3 Ton All-in-One UniJack is designed to safely lift and hold both regular and unibody cars and trucks.

All Unibody vehicles have factory-approved lifting points to prevent damage when jacking up the vehicle. But with a conventional jack, it’s challenging to properly lift and hold a unibody vehicle, because once the vehicle is raised with a jack, there’s no space left to add a jackstand.

The Powerbuilt 3 Ton All-in-One solves this problem with an ingenious design that both safely lifts and securely holds a Unibody vehicle using a single lift point. The Unijack offers both concave and flat lifting surfaces to accommodate a wide variety of lift points.

What’s more, it eliminates the cost and hassle of a floor jack, it’s easier to lift, move and store and costs a lot less too.

The 6000 pound All-in-One offers lift range from 11 to 21 inches, which makes it perfect for trucks, SUVs and vans.

Product description

Pro lift F-2315PE hydraulic trolley jack has the 3000 lbs. capacity. It gives you the ability to lift from 5.25" to 12". it is built with All welded steel frame construction and rust-resistant. Large steel casters and swivel casters provide easy maneuverability.

• Min. Height: 5.25", Max. Height: 12"
• All welded Steel frame Construction with rust resistant
• Large Steel casters and swivel casters for easy maneuverability
• Sturdy carrying handle
• Blow mold case for easy storage

User questions & answers

Question:	Is it good for a 2016 lexus is 200t fsport
Answer:	This is a small jack that is good for something the size of a Camry. I did use it once on a Toyota Prado Land Cruiser with blocks of wood and it struggled. It is not commercial quality. and
Question:	Is this good for a 2012 chrysler
Answer:	good for any car with the clearance. always check your manufacturer owners manual for auto jack lift points. many cars use unibody construction and serious damage can occur if jack placed incorrectly.
Question:	Is it good for changing tire on riding lawnmower
Answer:	Don’t buy it... i did and it works only two times 👎
Question:	Is it good to use on a 2003 subaru outback wagon
Answer:	It’s garbage. Don’t waste your money. Spend a little more and get something that you can trust. Mine failed the first time trying to lift a compact car.

Product features

Pro-LifT

Our lifting equipment products have consistently led the industry in quality and innovation. Designed after professional grade equipment standards, Pro-Lift equipment is kept under close quality control standards from factory to your home. Our products provide a unique twist to your garage maintenance needs.

Product description

The Torin BIG RED T10152 steel scissor lift jack car kit is a collapsible, compact jack can be used as a rugged replacement jack or as an extra utility jack that can be stored in the trunk of your car. Engineered using a drop forged alloyed steel construction for quality and durability and features a lifting range of 4-1/8" to 15-1/8" with a 1.5 ton (3,000 lb) capacity. It's equipped with an extra-wide base which adds stability and strength. The 1 piece handle delivers on-the-spot quick response and speed to get the job done quickly and safely. This unit is 100% factory tested for reliability and safety to meet and comply with ANSI/ASME PASE safety standards. Includes a limited 1 year manufacturer warranty.

• Collapsible, steel scissor lift jack has a compact design that can be used as a rugged replacement jack or as an extra utility jack that can be stored in the trunk of your car
• Features a lifting range of 4-1/8" to 15-1/8" with a 1.5 ton (3,000 lb) capacity
• Engineered using a drop forged alloyed steel construction for quality and durability
• Equipped with an extra-wide base which adds stability and strength; 1 piece handle delivers on-the-spot quick response and speed
• Meets ANSI/ASME PASE safety standards and includes a limited 1 year manufacturer warranty

User questions & answers

Question:	Can you tell me the width of the base on this jack? Thanks. RMW
Answer:	The base is 6&1/2" wide, is 4&1/2" deep at the ends, but narrower at the middle. Realize that made-in-China items can quickly change depending on their latest vendor, i.e., low-bidder. I'm happy with mine, although the picture for mine showed it had a flat top, and mine has two small bumps that protrude--although only a very little bit. These might provide stability in some situations, don't pose a problem in most, but I'd have peferred that the top be flat.
Question:	what is the fully collapsed height -- will it fit within a gap of 3-3/4 inches
Answer:	Yes. It will clear that distance. Its collapsed height is 3 1/2 inches.
Question:	Can you tell me about the length of the jack when it closed , I want to see if it match it's place in my car ( Toyota Camry
Answer:	When completely closed, as flat as can be, this item measures 5" high, 5" wide and 18" long.
Question:	Will this jack for toyota corolla le 2009 model
Answer:	I'm sure it will work for the 2009 Toyota Corolla. The limit on the Jack is 3,000 pounds. This jack should easily lift the weight from one side or one corner. Be sure the jack is firmly under a frame member. I would recommend a Jack stand or blocks to place under the frame in the event of a mishap.

Product features

Torin BIG RED Steel Scissor Lift Jack Car Kit, 1.5 Ton (3,000 lb) Capacity

Product description

The Torin BIG RED T83006 hydraulic trolley floor jack is constructed with heavy duty steel, providing long term durability with an industrial luster. This floor jack has a 3 ton (6,000 lb) capacity and features a minimum lifting height of 5-7/8" and a maximum height of 20-7/8", which is ideal for most cars, trucks, vans, and SUVs. The single piston quick lift pump allows you to easily raise the jack to the desired height. A safety bypass system prevents over-loading and ensures safe operation. Equipped with large steel casters and 360-degree swivel casters for smooth maneuverability. The extra long saddle neck saves time when lifting higher vehicles. A built-in carrying handle allows for the floor jack to be lifted and moved quickly. Includes a limited 1 year manufacturer warranty.

• Hydraulic trolley floor jack is constructed with heavy duty steel, providing long term durability with an industrial luster
• Features a 3 ton (6,000 lb) capacity with a minimum lifting height of 5-7/8" and a maximum height of 20-7/8"; Ideal for most cars, trucks, vans, and SUVs
• Equipped with large steel casters and 360-degree swivel casters for smooth maneuverability; Extra long saddle neck saves time when lifting higher vehicles.Handle Length:24.5 inch
• Single piston quick lift pump allows you to easily raise the jack to the desired height; Safety bypass system prevents over-loading and ensures safe operation.Rubber-tipped tongs
• Built-in carrying handle allows for the floor jack to be lifted and moved quickly; Includes a limited 1 year manufacturer warranty

User questions & answers

Question:	i actually have 2 questions. Can this lift a ford explorer and can the long neck be removed
Answer:	The height is 9 1/4"+ a fraction. If you want to say 9 3/8" to be on the safe side you should be good.
Question:	Is there a longer neck I can buy for it
Answer:	Home Depot's website says 10-1/8 to 16-3/8 in.
Question:	Made in USA
Answer:	Home Depot's website says 10-1/8 to 16-3/8 in.
Question:	With long neck attached, and jack all the way down, what is the height
Answer:	Walmart's website says the non-double pin version is made in China so I assume this version is too.

Product features

Torin BIG RED Hydraulic Trolley Service/Floor Jack with Extra Saddle (Fits: SUVs and Extended Height Trucks): 3 Ton (6,000 lb) Capacity, Red

Product description

Great Addition to any Garage and Home

Pro-Lift B-004D Grey Hydraulic Bottle Jack is a 4-ton bottle jack that is ideal for auto, truck service, farm and shop use. With the heat treated critical stress areas, it ensures long life performance. In addition, the carrying handle makes it so easy to carry around wherever need it.

It features the steel lifting saddle that is engineered to hold load securely.

With the extension screw, it allows Pro Lift B-004D Bottle Jack to be adjusted to accommodate desired work height.

Pro Lift B-004D Bottle Jack also features Built-In bypass system to protect against ram over-travel.

- Steel Lifting Saddle Engineered to Hold Load Securely 

- Extension Screw Adjusts to Accommodate Desired Work Height 

- Built-In Bypass System to Protect against Ram Over-Travel 

- Heat Treated Critical Stress Areas 

- Designed to Meet the Latest ANSI/PALD Standards

Specifications

- Capacity: 4 Ton 

- Lifting Range: 8 x 15-3/8 inch 

- Carrying Handle: No 

- Item Weight: 9 Lbs

Pro Lift B-004D Bottle Jack is backed with SFA 90 Days Warranty from the Date of Purchase.

Grab one now to add to your home tool set

• The product is 4Ton bottle jack
• Easy and simple use kit
• The product is manufactured in china
• Steel lifting saddle engineered to hold load securely
• Extension screw adjusts to accommodate desired work height
• Built-in bypass system protects against ram over travel
• Heat treated critical stress areas ensure long life performance
• Designed to meet ANSI/PALD standards

User questions & answers

Question:	What is the diameter of the jack pad on the top of the pad
Answer:	Without going to the garage, I would guess 1 1/4"
Question:	How tall is it closed
Answer:	In the product description it states this - Lifting Range: 8 x 15-3/8 inch So I would think that it is 8" closed and lift up to 15-3/8 inches Plush the top screws up & down some?
Question:	is there anything we can fix the bottom to make sure it doesnt fall to side
Answer:	It shouldn't fall. But if your still concerned you could drill holes on the base and mount it to a piece of wood.
Question:	Do i need to buy the oil seperate
Answer:	no

Product features

Pro-Lift Grey Hydraulic Bottle Jack

Our lifting equipment products have consistently led the industry in quality and innovation. Designed after professional grade equipment standards, Pro-Lift equipment passes current standards and is kept under close quality control from factory to your home. Our products provide a unique twist to your garage maintenance needs.

• Steel lifting saddle cleared for load gripping power
• Extension screw adjusts to accommodate work height
• Heat treated critical stress areas ensure long life performance

Product description

Fast Lift to the Jacking Point

Blackhawk B6350 Service Jack is a 3-1/2 ton (7,000 lbs) capacity service jack that features the unique design of fast list technology to fast lift to the jacking point with no load.

It features the swivel saddle that provides you with the easy jack positioning and user safety. Its heavy duty steel construction also provides you the safe use and long term durability.

Blackhawk B6350 Service Jack also features the bypass device that preventing the damage from over pumping.

Blackhawk B6350 Service Jack also features the built-in internal safety valve and vent plug to ensures the safe operation.

- 3½Ton (7,000 Lbs.) Lift Capacity

- Fast Lifting Technology

- Heavy Duty Steel Construction & Swivel Saddle

- Built-In Safty Valve and Bypass Device

Blackhawk B6350 Service Jack is backed by the full one year warranty from the date of the purchase.

Click the buy button now to get your long lasting professional sevice jack

• Built-in internal safety valve and vent plug ensures safe operation
• Swivel saddle provides easy jack positioning and user safety.Saddle Diameter: 4 inch
• 3.5-ton/7,000 lb. lift capacity
• Jack Size: 28 1/2" L x 13 3/4" W x 6 1/2" H
• Rugged universal joint for precise load control
• Great for working in the garage and other outdoor activities such as picnics or ball games
• Note: The hydraulic jack is designed to lift, not to support the object. Immediately after lifting, loads must be supported by a pair of appropriately rated jack stands

User questions & answers

Question:	Hi, Wondering if it will fit my new XtremepowerUS 1/2 Ton Transmission Hydraulic Floor Jack Adapter it has a 1 1/4 inch hole
Answer:	I would say no. The hole in this jack only measures 1 1/8". It would seem your adapter needs an 1 1/4" hole for the "peg" to drop into .
Question:	How high does it lift
Answer:	The lifting range on the jack is 5.5" to 22" H.
Question:	Will this fit under a low profile car like a 350Z
Answer:	It's unlikely. I have a 2006 Mustang GT. If I'm not mistaken, a Mustang has about the same ground clearance as a 350Z. The jack will not fit under my Mustang. It's about an inch or two too tall. It is a great jack in spite of this. I use it on my other vehicle.
Question:	Anyone know of any jack that has this weight capacity, but is made in the USA
Answer:	My Blackhawk B6350 I bought 3 months ago has a made in the USA sticker. For whatever that means. Maybe to sticker was made here!

Product features

Lifting Range: 5.5 inches - 22 inches

• Note: Before it uses, it needs to make sure the release valve needs to be turned clockwise until the firm resistance is felt.
• Note: Since the hydraulic jack is designed to lift, not to support the object. Immediately after lifting, loads must be supported by a pair of appropriately rated jack stands

Product description

The Torin BIG RED T90603B hydraulic bottle jack is designed for residential and commercial use. It is industrial welded and engineered using a drop forged alloyed steel construction that is ideal for quality and durability. The inner/outer welded structure and steel construction will keep your bottle jack leak-free and give it an overall stronger build. The fully welded structure is designed for hard-hitting commercial use, making large loads easy to lift. A wide, rugged base adds stability and strength. The lifting range is 8-1/2" to 16-1/4" with a 6 ton (12,000 lb) capacity. It features a high-quality glide-action pressure pump designed to lift with minimal muscle and effort and has an integrated built-in oil-bypass and overload valve that protects the hydraulic system from extending beyond its travel limits. Hydraulics are powered with a high-quality oil, which offers better corrosion resistance and high/low temperature flexibility, allowing the unit to operate at temperatures between 40 degrees Fahrenheit and 105 degrees Fahrenheit. Piston ram utilizes a Y-style polyurethane sealing ring with backup ring, preventing the load from falling slowly. This powerful bottle jack is ideal for lifting cars, trucks, SUVs, farm vehicles, heavy-duty machinery and industrial equipment. It can also be used for military applications, agricultural and industrial environments where the equipment receives heavier abuse. This unit is 100% factory tested for reliability and safety to meet and comply with ASME PASE safety standards. Includes a limited 1 year manufacturer warranty.

• Hydraulic bottle jack designed for residential and commercial use; Serrated, heat treated saddle provides generous lifting area and secure grip
• Features a lifting range of 8-1/2" to 16-1/4" with a 6 ton (12,000 lb) capacity; Adjustable screw top extension adds versatility
• Engineered using a drop forged alloyed steel construction for quality and durability; Inner/outer welded structure delivers leak-free performance
• Glide-action pressure pump is designed to lift with minimal effort; Integrated built-in oil-bypass and overload valve that protects the hydraulic system from extending beyond limits
• Meets ASME PASE safety standards and includes a limited 1 year manufacturer warranty

User questions & answers

Question:	Jack won't come down
Answer:	same problem here. 20 ton. returned one, and new replacement does the same thing. over 100lbs of pressure and still no lower. must stand on... which is effing hard when in a crawlspace.. hard to remove from area jacked up also, because wont lower.
Question:	How tall is this jack when all the way down? I need to get it under 9" high car frame
Answer:	The jack is less then a foot high but it probably at least nine inches. I keep it in the back of my jeep and haven't measured it. If I get a chance I'll do it later and respond again.
Question:	Is there a way to immediately let the whole thing reset (go down to its non pumped height
Answer:	Neighbor ... sounds like you are a newbie. We were all that, once. The handle fits over the operating valve and piston action depends on whether it is open or not. Twist clockwise to close and pump .... the piston goes up. Twist counterclockwise to open and the piston retracts .... if, there is sufficient weight on it or it has a spring to retract the piston. The large screw in the top is manually adjusted out or in. Please remember that this unit isn't reliable enough for you to get under the car after you have lifted it. Jack stands are needed and you must be certain that the car cannot move. That means emergency brake set and wheel chocks are needed. Sorry if I got too specific or described things you already knew. Just tryin' to be a good neighbor .... ron :-)
Question:	What is the diameter of the ram
Answer:	The top of the ram IS 1.084", (NOT 1 and 1/8 inches). The cylinder raising that top IS 1.1 inches (NOT slightly wider at 1.25 inches). The base of the unit is roughly IS 3.7" x 3.85 " (NOT 3.5" x 4.5") and IS approximately 7" (NOT 9") tall before raising ram.

Product features

Torin BIG RED Hydraulic Welded Bottle Jack, 6 Ton (12,000 lb) Capacity

Handle Tool

Includes pump handle with plastic sheaths

Steel Construction

Engineered using a drop forged alloyed steel construction for quality and durability. Inner/outer welded structure delivers leak-free performance

Glide-Action Pump

Features a high-quality, glide-action pressure pump designed to lift with minimal effort

Serrated Saddle

Serrated, heat treated steel saddle provides a generous lifting area and a secure grip

Product description

What happens when a vehicle without an axle beam rolls into your garage? You pull out your OEMTOOLS 24833 Floor Jack Crossbeam. Compatible with any floor jack that has a 1-1/8 inch diameter saddle stud, the service jack cross beam comes pre-assembled. The steel floor jack cross beam takes mere minutes to attach to the jack with a mounting peg. Depending on the size of the car, the saddle on the cross beam jack adapter extends from 23 inches to 32 inches from the center. The threaded pad design on the floor jack attachment gives you an extra 2 inches for exact adjustments. On each end of the garage floor jack crossbeam, there are two rubber lift pads that provide extra security so you don’t have to worry about slipping. You can use the automotive floor jack crossbeam to lift cars at rocker panels for simultaneous wheel service, brake inspections, steering inspections, suspension repairs, oil filter changes, and more. The low profile of the garage car jack crossbeam allows you to easily slide beneath parked vehicles. The garage jack crossbeam greatly reduces the chance of undercarriage metal damage and provides stability for the entire front, rear, or side of a lifted vehicle. This powerful tool can hold up to 3000 lb. at the minimum width and up to 4000 lb. at the maximum width.

From the Manufacturer

A sturdy welded steel cabinet. It is a self- contained unit operating on 115V alternating current and connects to your present air supply. The unit is equipped with an internal blasting gun that controls the air flow. Years of blasting experience are molded into the Bench-Top to offer a cabinet that is durable, highly efficient and inexpensive. We are convinced that this machine is the practical answer to automobile rebuilders, diyr's, pros, and many industrial applications where quality finishing and cleaning is needed at a fraction of the conventional time required

• COMPATIBLE: The low profile jack crossbeam is compatible with any 1-1/8 inch floor jack; No need to search for special parts or attachments; Low profile car jack crossbeam features 1.5 to 2 ton rated capacity
• AIDS IN REPAIRS: The 1.5 to 2 ton floor jack crossbeam helps lift vehicles without axle beams to help aid in repairs like tire changes, brake inspections, oil drain plug replacements, oil filter changes, steering and suspension repairs, and more
• EXPANDABLE REACH: Easily slide out the bars to extend the reach from 23 inches to 32 inches; Threaded pad design on 1.5 to 2 ton jack crossbeam provides an additional 2 inch adjustment; Adjusts to fit most vehicles
• SECURE AND STABLE: The rubber lift pads on the low profile floor jack crossbeam offer slip-free security to keep vehicles stable; Reduces risk of undercarriage metal damage; Offers maximum durability due to the heavy steel construction
• EASY SET UP: The cross beam adapter for floor jacks comes pre-assembled and ready to use out of the box; Takes minutes to attach crossbeam to any standard jack

User questions & answers

Question:	My question is this a 2 ton cross bean and will it fit over my 3 ton low profile pittsburgh floor jack
Answer:	It you can take the saddle out of Jack . The measure of the pin is 1.143 inch
Question:	Hi..What is the max distance from center of pad to center of pad
Answer:	They ended up no sending to me after ordering and waited about 6 weeks.
Question:	What is the exact mounting pin diameter? The 1?1/8" in the description really makes me wonder. Thank you
Answer:	it measures 1.145 inches
Question:	will this work as a motocycle jack
Answer:	No it will not for a motocycle jack

Product features

OEMTOOLS 24833 Floor Jack Crossbeam

Your repairs are about to get a lot easier. The OEMTOOLS 24833 Floor Jack Crossbeam works with any 1-1/18 inch floor jack and has a 1.5 to 2 ton rated capacity. It takes mere minutes to attach to the jack. Lift vehicles to help with repairs like brake inspections, tire changes, oil drain plug replacement, steering repairs, oil filter changes, and more. The saddle extends from 23 inches to 32 inches to give you more length to work with depending on the size of the vehicle.

Lift Vehicles without Axle Beams

Have a car without an axle beam? The OEMTOOLS 24833 Floor Jack Crossbeam slides easily under parked vehicles and works with any standard garage jack. There's no need for any special parts or tools. The crossbeam comes ready to use out of the package so you can get right to work.

Huge Weight Capacity

This powerful tool can hold up to 3000 lb. at the minimum width and up to 4000 lb. at the maximum width.

Extra Adjustments

In case you need more height, the threaded pad design provides an additional 2 inch adjustment to fit your needs.

Better Stability

The floor jack crossbeam is outfitted with rubber lift pads to make sure you have a slip-free experience.

Easy to Attach

It's simple to attach the floor jack crossbeam to any floor jack that has a 1‐1/8 inch diameter saddle stud.

Product description

With this scissor jack you can easily and safely move your vehicle to the desired height.

The handy, included ratchet wrench and built-in, easy-to-use spindle, make the wheel change a breeze. In addition, the heavy base plate provides a secure stand.

You get new goods in the best quality.

Characterized by safe carrying capacity,withstands high pressure,corrosion-resistant,should not be missing in any vehicle,Strong metal construction made of steel.

Product Features:

Product type: Scissor Jack with Ratchet Wrench

Maximum load capacity: 2.0T (2000kg/4,409 lbs) 

Minimum lifting height: approx. 250 mm/9.8"

Maximum lifting height: approx. 385 mm/15"

Product dimensions: 480 x96 x 98 mm(18.9x3.8x3.8" )

Product weight net: 3330 kg/ 7.3lbs

Product weight gross: 3.55 kg/ 7.4lbs

OPERATION MANUAL:

1. Insert the handle into the hole of the grip sleeve.

2. Make sure the saddle is correctly positioned. To avoid damaging the socket, do not move the socket while the handle in the socket is intact.

3. To increase the load, use one hand to hold the front part of the handle and turn the other hand clockwise at the back of the handle.

4. To lower the load, use one hand to hold the front part of the handle and slowly turn it counterclockwise with the other hand at the back of the handle.

Package included:

- 1x 2T Jack

- 1x Ratchet Wrench

• ★ Maximum load: 2.0T (2000kg/4,409 lbs); Recommoned Lifting height: 9.8"~15"(250m - 385mm); Net weight: 7.3lbs /3.30kg
• ★ With the scissor jack you can easily and quickly adjust the height of your vehicles. Thanks to the handy hand crank and the smooth-running spindle, changing tires is child's play from now on
• ★ Product features: The solid base plate also ensures a secure footing, corrosion-resistant, Strong metal construction made of steel, withstands high pressure
• ★ Suitable for: Station Wagon, Van, SUV, Large Van, Mini Bus
• ★Including: 1x 2T jack ;1x Ratchet wrench

User questions & answers

Question:	The purpose of the blue towel in one of the pictures
Answer:	Hi, dear, thanks for your asking. The blue towel prevent scratches on the paint surface, but in our package include not this part.
Question:	i can used in ford explorer
Answer:	Oh yes you can!
Question:	What's the size of the hex head on the jack that the included ratchet wrench attaches too
Answer:	3/4inches(19mm)
Question:	Will this work with Tesla Model Y the close position should be
Answer:	Do not use this jack for anything. It is unsafe and dangerous. Bad design