9 best ton aluminums

Ton aluminum is not a specific term or product related to floor jacks, jacks, vehicle lifts, hoists, garage shop tools, equipment, or automotive applications. However, it seems like you might be referring to aluminum construction in these types of tools and equipment.

Aluminum is a lightweight and corrosion-resistant metal that is commonly used in various automotive tools and equipment due to its durability and weight-saving properties.Floor jacks, jacks, and vehicle lifts may use aluminum components or alloys to reduce overall weight while maintaining strength and performance. This can make these tools easier to maneuver and transport.

Aluminum is also commonly used in the construction of hoists and other lifting equipment, as it provides a good balance between strength and weight. Garage shop tools and equipment, including automotive tools, may incorporate aluminum in their design to enhance portability and durability.

In summary, while "ton aluminum" isn't a specific term or product, aluminum is often used in the construction of various tools and equipment related to automotive and garage shop applications to provide strength, durability, and reduced weight.

Below you can find our editor's choice of the best ton aluminums on the market
  

Arcan 3-Ton Quick Rise Aluminum Floor Jack with Dual Pump Pistons & Reinforced Lifting Arm (ALJ3T / A20018)

Arcan

Based on 1 reviews Check latest price

Product description

The Arcan ALJS3 3-Ton Steel Jack Stands has an overall 3-Ton lifting capacity and a working range of 11-5/8 in. to 17.5 in. A counterweighted pawl locks in place securely to prevent slipping, while allowing easy adjustments. A large contoured saddle with locating lugs helps support and position vehicle frame. The wide stance base delivers superior stability and includes base pads that prevents the jack from sinking into asphalt and provide stable footing for the jack stands. The welded construction and alloyed steel offer years of support. Arcan puts all of our lifting equipment through voluntary and rigorous third party safety testing, as outlined by the ASME PASE-2014 Safety Standard for Portable Automotive Service Equipment, to ensure that our products are among the safest on the market.

  • COLORS MAY VARY: ALJ3T (silver) or A20018 (green)
  • LIGHTWEIGHT AIRCRAFT-GRADE ALUMINUM: Allows for easy maneuverability.
  • DUAL PUMP PISTONS: Quickly raises the floor jack saddle to load.
  • REINFORCED LIFT ARM: Increases strength, chassis torsion control, and durability.
  • VEHICLE PROTECTION: Designed with a rubber saddle and a foam handle bumper.
  • SIDE-MOUNT HANDLE: Allows for convenient jack positioning.
  • 2 PIECE HANDLE: Allows for easy storage.

User questions & answers

Question: how smoothly and slow can a vehicle be lowered
Answer: This fuel pressure reghulator is set at 43 PSI - identical to the OEM regulator. -Sean 818-574-FUEL
Question: What is the height range
Answer: Yes, this will fit the 2013-2018 Can-Am Maverick / Maverick Max 1000 . -Sean 818-574-FUEL
Question: How big is the saddle and rubber pad on this jack
Answer: This will be a 100% direct fit for the 2009-2018 Outlander 650. -Sean 818-574-FUEL
Question: where is arcan made
Answer: Yes, this will be a 100% direct fit for the 2013-2015 Can-Am Maverick 1000. -Sean 818-574-FUEL

Arcan 3 Ton Hybrid Heavy Duty Aluminum and Steel Low Profile Floor Jack (HJ3000A/A20001)

Arcan

Based on 163 reviews Check latest price

Product description

The Arcan HJ3000A/A20001 3 Ton Hybrid Jack has a 3 ton lifting capacity with an aluminum construction and steel frame that provide the benefit of strength within a light weight chassis weighing a total of only 58lbs The dual pump pistons quickly raises the floor jack saddle to the load and is designed with a rubber saddle and a foam handle bumper to protect the vehicle The side handle allows you to easily carry this jack around the garage We put all of our lifting equipment through voluntary and rigorous third party safety testing as outlined by the ASME PASE-2014 Safety Standard for Portable Automotive Service Equipment to ensure that our products are among the safest on the market

  • MODEL NUMBER MAY VARY: HJ3000A = A20001
  • HYBRID CONSTRUCTION The aluminum and steel frame provide the benefit of strength within a light weight chassis
  • DUAL PUMP PISTONS Quickly raises the floor jack saddle to load
  • VEHICLE PROTECTION Designed with a rubber saddle and a foam handle bumper
  • SIDE HANDLE For easier carrying
  • LIGHTWEIGHT Aluminum construction provides a total weight of only 58lbs
  • COMPLIES WITH ASME PASE-2019 SAFETY STANDARD We put all our lifting equipment through voluntary and rigorous third party safety testing to ensure our products are among the safest in the market
  • LIFTING RANGE: 4" to 18. 5"

User questions & answers

Question: Does this ship to APO
Answer: yes
Question: Does the saddle swivel
Answer: Yes, the saddle does swivel. I might add that I have been around this type of jack for many years. I consider this one to be very good.
Question: Can you attach 4000 lb cap crossbeam to the saddle
Answer: It's hard to say the saddle pin is threaded not a slip on
Question: Jack just arrived. A black plastic lock on top of the socket handle prevents it from pumping up/down. How do I go about it
Answer: Not too sure what you are talking about, but the handle slides into the receiver and knurl knob is turned to lock it in.
Question: How does this differer from the arcan alj3t? they're both 3-ton, same maker and both weigh almost the same, yet the other is about $100.00 more
Answer: On this jack, what you see painted in red, the frame, is aluminum. The silver parts, like the lifting arm is steel. I don't know for sure about alj3t, but I think the lifting arm is aluminum as well as the frame. That would explain the weight difference, which looks like it is about 2lbs.
Question: Is this a low profile jack and does it have the 3 pump rapid lift feature
Answer: this has rapid 2 pump design, says it in the product description. hope that helps and others interested should know.
Question: Does this jack have a 1 yr warranty? To anyone that has had this for some time how is it holding up? Will this lift a 3/4 ton truck? Thanks
Answer: Can't answer the warranty question, but it works great on my one ton F350 dually. Great jack so far and used it alot. I throw it in the back when camping out in the mountains.
Question: How much does this floor jack weigh
Answer: 58.3 lbs. I bought mine from Costco Wholesale for $99.99. its supposed to be lighter than others but its still a beast. Then again its supposed to lift 3tons. Better that its solid and heavy than cheap and flimsy. Don't forget to get jack stands.

JEGS Professional Low-Profile 3-Ton Aluminum Floor Jack | 3 ½ Inch Minimum Saddle Height | Lightweight Construction | 360 Degree Rotating Saddle

Based on 262 reviews Check latest price

Product description

Professional Low-Profile Aluminum Floor Jack

  • 3 Ton
  • Low-Profile - 3 1/2 in.
  • Weight: 58 lbs
  • Lifting Capacity: 6,000 lbs.
  • 4 9/16 in. Dia. Lifting Pad
  • Meets ASME PALD 2014 standards

    Features:

  • Aluminum construction
  • Lightweight
  • Saddle rotates 360 degree
  • Minimum Saddle Height: 3 1/2 in. (good for low-clearance vehicles)
  • Maximum Saddle Height: 19 1/4 in.
  • 50 in. two-piece handle with sleeve (protects vehicle during use)
  • Knurled grip reduces slippage
  • Dual side handles simplify maneuvering/positioning
  • Hydraulic Lift: 15 3/4 in.
  • Rubber lift pad prevents marring
  • Chassis Length: 26 1/2 in.
  • Chassis Width: 13 in.
  • Seals protect hydraulic system from contaminants
  • Overload & bypass valves prevent jack from being used beyond its rated capacity
    • LIGHTWEIGHT ALUMINUM CONSTRUCTION allows you to roll jack around with ease
    • LOW PROFILE DESIGN lifts from 3 ½ to 19 ¼ inches
    • 360 DEGREE ROTATING SADDLE allows for easier movement
    • RUBBER LIFT PAD prevents marring of surfaces
    • OPTIONAL JACK SKID available separately to use safely on dirt, gravel, and grass

    User questions & answers

    Question: Where is it made
    Answer: This jack is made in China, but considering, is excellent quality. It’s a Sunex Tools product with a nice JEGS paint job.
    Question: where is this product manufactured
    Answer: I think I saw Taiwan on mine, but VERY good quality. I have a MATCO aluminum jack and it looks identical to it, and it was made in Taiwan. I have a Snap-On that was made in China, but it's been a good jack also. My MATCO jack is over 13 years old and still works great.
    Question: What material are the wheels made of
    Answer: Steel wheels. This is a big Jack, and heavy.
    Question: How many pumps until it's fully extended
    Answer: I haven’t paid attention to it but this is not a quick one, It will take several pumps until fully extended, if I had to throw a number out there I’d say..15🤔? But if you don’t have enough clearance to reach full pumps, it will take several more.

    1.5 Ton Compact Aluminum Racing Jack with Rapid Pump

    PITTSBURGH At The Neighborhood Corner Store

    Based on 459 reviews Check latest price

    Product description

    This compact racing jack is constructed with durable, aircraft aluminum billet. A knurled aluminum handle ensures a steady grip while you quickly lift your load in just 3-1/2 pumps! The racing jack also features a universal joint release mechanism for smooth, precision lowering and a compact design for easy storage and transport.* Color: Blue * Handle type: Knurled Aluminum * Lifting range (in.): 3-3/8 in. - 14-3/4 in. * Material: Aluminum * Handle Length (in.): 37-3/8 in. * Maximum Lift Height (in.): 14-3/4 in. * Minimum height (in.): 3-3/8 in. * Product Length: 22-1/3 in. * Product Weight: 26.8 lbs. * Product Width: 9-7/16 in.

    User questions & answers

    Question: Does the handle fold over to fit in a trunk or does it come off easily
    Answer: Look at the 1st question above, the handle comes off too easily, several people have lost them and cannot replace them.
    Question: Will it hold my 98 bmw 328i
    Answer: It will LIFT your car, and MAY hold it. Whatever you do, don't trust this jack to get under the car without using jack stands. YES I KNOW THAT SHOULD BE SAID ABOUT ALL JACKS but a lot of people ignore that common sense advice. I bought one of these jacks at a HB outlet becaue I was on the road and needed to do some emergency repair on my car. The jack has a tendency to let the car down when its set to hold it. Not all the time, and not always the same speed, but it does it enough to make it dangerous!!
    Question: How do I order parts for this jack
    Answer: You have run into the same problem I did. These are really inexpensive jacks so I think the only way to get parts is to buy another jack. Sorry.
    Question: Am very dissappointed in the price!!! Harbor Freight has it for 59.99! I hope you can give me that price or I'll have to return it? please help
    Answer: Its “ I am “ not “Am”. Irritating reading folks type like this.

    NOS NSJ0301 3-Ton Aluminum Service Jack

    Sunex Tools

    Based on 207 reviews Check latest price

    Product description

    NOS NSJ0301 Aluminum service Jack - 3 ton Capacity

    • Lift capacity: 3 Tons (6,000-Pound)
    • Height range: 3.75 in to 18.125 in
    • Ultra lightweight aluminum construction at just 58-Pound. Thick frame side plates and reinforced lift arm for added strength, chassis torsion control and durability
    • Safety valve prevents overloading
    • 2 Piece handle with bumper pad

    User questions & answers

    Question: Will this fit under a 1991 corvette
    Answer: From the floor to the jack pad is 3 3 /4 inches high and goes under vehicle about 6 inches before hitting Hope this helps!!
    Question: Can I Extend my warranty
    Answer: We do not offer extended warranties.
    Question: how many pounds is it 27 pounds or is it 60 poounds
    Answer: Mine is about 54 pounds. I'm not sure what part of it would only be 27 pounds. It's easy to maneuver so weight is not an issue for me. This is a nice jack. I only have 2 cars, so I have only used it 3 times since I bought it and I have no complaints.
    Question: I want to order the 3 ton jack but only if it has the metal wheels
    Answer: Yes the 3 ton looks like some sort of metal i own 1

    NOS NSJ0201 2-Ton Aluminum Service Jack

    NOS

    Based on 24 reviews Check latest price

    Product description

    NOS NSJ0201 Aluminum service Jack - 2 ton Capacity

    • Lift capacity: 2 Tons (4,000-Pound)
    • Height range: 3.5 in to 19.5 in
    • Ultra lightweight aluminum construction at just 47-Pound
    • Safety valve prevents overloading
    • 2 Piece handle with bumper pad

    User questions & answers

    Question: What is the weight of the 2 ton nos nsj0201 model? it says 27 lbs in some places and 56 in other places
    Answer: Made in Communist China
    Question: Jack is new out of the box and wont even lift my lawn mower, does this jack come pre filled with hydraulic oil
    Answer: I did not count, but over 10 strokes.
    Question: How tall is tallest point on this jack? Need floor jack with highest point no more then 5 5/8 inch
    Answer: The details page mentioned it originated in China and has a 1 year warranty. I bought this for my husband and he loves it. Heavy duty - jacked up a 1967 Buick GS easily :)
    Question: Where is this made
    Answer: The wheels are made of a hard plastic which has held up well. I hope this helps.

    BIG RED T84025B Torin Hydraulic Low Profile Aluminum and Steel Racing Floor Jack with Dual Piston Quick Lift Pump, 2.5 Ton (5,000 lb) Capacity, Black

    BIG RED

    Based on 81 reviews Check latest price

    Product description

    Torin Jack Aluminum and Steel Racing Jack - 2.5 Ton Quick-lift design to reach a maximum height. Saddle can be removed. 2-1/2 ton Lift Capacity. Minimum Lift Height: 4-1/8inch, Maximum Lift Height: 18-1/4inch. Aluminum and Steel metal frame. It only takes 7 strokes to reach the maximum lift. Base: 26-3/8inch x 12-1/2inch.

    • Quick lift design
    • Removable saddle
    • Minimum Lift Height: 4-1/8inch
    • Maximum Lift Height: 18-1/4inch
    • 7 strokes to maximum height

    User questions & answers

    Question: What size is the lifting plate
    Answer: The lifting plate is round 4 3/8 in Awesome Jack love it
    Question: is this heavy
    Answer: It is a bit heavy. Reported stats in the item description. It weighs 60 lbs.
    Question: Does it come with the lever arm
    Answer: Of course :)
    Question: In what country is this jack made
    Answer: This item is made in China, this same product is sold as several other brands but it's from the same manufacturer from China.

    Product features

    Torin BIG RED Aluminum/Steel Racing Floor Jack: Dual Piston Pump, 2.5 Ton (5,000 lb) Capacity

    • Racing floor jack can be used for general or specialty use and features a 2.5 ton (5,000 lb) capacity
    • Lift range between 3-15/16" to 18-5/16" allows you can gain easy access under low-profile vehicles, making the placement on the undercarriage of any vehicle is easy
    • Constructed of durable, high-strength aluminum and steel
    • Equipped with dual side handles, which makes moving and carrying the jack quick and simple
    • Foam bumper on the handle helps prevent against vehicle damage while in use

    JEGS Professional Low-Profile 2-Ton Aluminum Floor Jack | 3 ½ Inch Minimum Saddle Height | Lightweight Construction | 360 Degree Rotating Saddle

    Based on 129 reviews Check latest price

    Product description

    Professional Low-Profile Aluminum Floor Jack

  • 2-Ton
  • Low-Profile - 3-1/2"
  • Weight: 49lbs
  • Lifting Capacity: 4,000 lbs.
  • 4-9/16" Dia. Lifting Pad
  • Meets ASME PALD 2014 standards Features:
  • Aluminum construction
  • Lightweight
  • Saddle rotates 360°
  • Minimum Saddle Height: 3-1/2" (good for low-clearance vehicles)
  • Maximum Saddle Height: 19-1/4"
  • 50" two-piece handle with sleeve (protects vehicle during use)
  • Knurled grip reduces slippage
  • Dual side handles simplify maneuvering/positioning
  • Hydraulic Lift: 15-3/4"
  • Rubber lift pad prevents marring
  • Chassis Length: 26-1/2"
  • Chassis Width: 13"

    • LIGHTWEIGHT ALUMINUM CONSTRUCTION allows you to roll jack around with ease
    • LOW PROFILE DESIGN lifts from 3 ½ to 19 ¼ inches
    • 360 DEGREE ROTATING SADDLE allows for easier movement
    • RUBBER LIFT PAD prevents marring of surfaces
    • OPTIONAL JACK SKID available separately to use safely on dirt, gravel, and grass
  • User questions & answers

    Question: Will mostly be used on trucks. curious if anyone has used this jack for their 4x4 pickups does this jack go high enough for this application? Thanks
    Answer: I have a stock Ford F150 Platinum 4x4 pick-up truck (year 2011), and my Jeggs 2 ton floor jack will lift any corner of the truck with no problem. If you just want to raise your truck high enough to get the wheels off the ground, then the lifting height is fine. If you need more height than that, then maybe others can give you the answer. I've only used it once to do a 4 wheel tire rotation.
    Question: is this JACK MADE IN THE ole grand USA , USA USA USA
    Answer: No it's made in China but is well made the only thing don't like about it , raise too slow , other than that is a good jack.
    Question: How low is low? When jack is down at its lowest position how many inches from ground to jack plate
    Answer: the height is 3.5 inches which is low enough to fit under my wife's mini cooper and lifts high enough to lift my 4wd Nissan titan. so far I love this jack.
    Question: is rated at 4000 lbs or 2 tons
    Answer: LOL and 1 ton = 2000 pounds. I had eggs for breakfast LOL

    Sunex 6603ASJ 3 Ton Aluminum Lift

    Sunex Tools

    Based on 39 reviews Check latest price

    Product description

    The Sunex Rapid Rise Technology reaches max height of 19.3 inches in 7.5 pumps. Side mounted handles for easy jack positioning. Wide track wheels for easy maneuverability. Rubber saddle pad and foam bumper pad protect vehicle. Thick frame side plates and reinforced lift arm for added strength, chassis torsion control and durability. Wiper seals protect hydraulic system from contaminants. Overload and bypass safety valves prevent the jack from being used beyond its rated capacity and ram over extension. Ball bearing mounted rear swivel coaster wheels and wide track front wheels for easy maneuverability. Two piece handle for storage; quick lock feature for engagement and disengagement of handle halves.

    • Rapid rise technology reaches max height of 19.3 inches in 7.5 pumps
    • Side mounted handles for easy jack positioning
    • Wide track wheels for easy maneuverability
    • Rubber saddle pad and foam bumper pad protect vehicle
    • Thick frame side plates and reinforced lift arm for added strength, chassis torsion control and durability

    User questions & answers

    Question: what is the height of the jack in the back. Want to see if low enough to reach jack points under a Mercedes E350 behind engine
    Answer: I just measured it at 6-1/2". I hope this helps.
    Question: Is it possible to fully lower handle without raising jack? My vehicle has a deep jack point and need to have handle fully down without the jack rising
    Answer: My jack CAME WITH A BROKEN CASTER WHEEL. They would not replace the wheel, so i RETURNED the jack :(.
    Question: What is the size of the saddle
    Answer: The saddle is 4.5" diameter, the rubber pad insert on the saddle is 4" diameter.
    Question: How long is the warranty
    Answer: one year, see the Sunex site; https://sunextools.com/products/6603asj-3-ton-aluminum-service-jack/

    Product features

    Vehicle Protection

    Designed with a rubber saddle and a foam handle bumper.

    Easy Jack Storage

    Handle can be seperated into two pieces for easier storage.

    Rapid Rise Technology

    Dual pump pistons quickly raise the floor jack saddle to load.

    Latest Reviews

    View all